advertisement
www.strong.tv
Digital Terrestrial HD Receiver PRIMA VII user manual bedienungsanleitung manuel d’utilisation manuale d'uso manual del usuario manual do utilizador felhasználói kézikönyv návod k obsluzei používateľská príručka
Instrukcja obsługi
Ръководство на потребителя
HOTLINE
AT
0820 400 150 [email protected]
€ 0,12/Min. österr. Festnetz
BG
CEE
+359 32 634451 [email protected]
+36 1 445 26 10 [email protected]
FR
0826 029 928 [email protected]
€ 0,15 par mn poste fixe en France
IT
199 404 032 [email protected]
Da rete fissa 24,8 cent. al min.
12,5 cent. scatto alla risposta
Da rete mobile max 49 cent. al min.
15,6 cent. scatto alla risposta
DE
0180 501 49 91 [email protected]
€ 0,14/Min. deutsches Festnetz
€ 0,42/Min. max. Mobilfunknetze
PL
UA
801 702 017 [email protected]
+380(44)228 24 73 [email protected]
www.strong.tv
Supplied by STRONG & Co, Japan
Represented by
STRONG Ges.m.b.H.
Franz-Josefs-Kai 1
1010 Vienna
Austria
Email: [email protected]
10 Sep 2014 11:43
Table of ConTenT
1.5 Usage of external USB devices
3.1 Connecting to a Terrestrial Antenna
3.2 Connecting to TV with HDMI cable
3.3 Connecting to TV with SCART cable
3.4 Connecting to a Digital Audio Amplifier with S / PDIF
3.5 Connecting to a Digital Audio Amplifier and TV using HDMI
3.6 Connecting to an analogue Audio Amplifier
3.7 Connecting a USB storage device
4.0 STarTIng up for The fIrST TIme
5.0 QuICk guIde To uSIng Your reCeIver
6.3 Selection of audio language
6.7 EPG (Electronic Programme Guide)
STrong declares that this item complies with the basic requirements and other relevant regulations of directives 2004/108/eC and 73/23/eC,
rohS 2002/95/eC
Subject to alterations. In consequence of continuous research and development technical specifications, design and appearance of products may change. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are registered trademarks of Dolby
Laboratories. All other product names are trademarks or registered trademarks of their respective owners. © STRONG 2014. All rights reserved.
1
2
1.0 InTroduCTIon
1.1 Safety Instructions
do noT InSTall Your reCeIver:
In a closed or poorly ventilated cabinet; directly on top of or under any other equipment; on a surface which might obstruct the ventilation slots.
do noT eXpoSe The reCeIver or ITS aCCeSSorIeS:
To direct sunlight or any other equipment that generates heat; to rain or intense moisture; to intense vibration and to any shock which may cause permanent damage to your receiver or to any magnetic objects, such as loudspeakers, transformers, etc.
Do not use a damaged power cord. It may cause a fire or an electric shock. Do not touch a power cord with wet hands. It may cause an electric shock.
When the receiver is not used for a long period of time, you should unplug the power
cord from the wall socket.
Do not use alcohol or ammonia based liquids to clean the receiver. If you wish, you may clean your receiver with a soft lint-free cloth slightly made damp with a mild soap solution, and only after disconnecting from the mains voltage supply. Make sure no foreign objects fall through the ventilation slots because this could cause fire or an
electric shock.
Do not place any objects on top of the receiver because this might prevent proper cooling of the components inside.
Safety precautions
Never try to open the receiver. It is dangerous to touch the inside of the receiver due to high voltages and possible electrical hazards. Opening the receiver will void the warranty of the product. Refer all maintenance or servicing to suitably qualified personnel.
When you are connecting cables, be sure that the receiver is disconnected from the mains supply voltage. Wait a few seconds after switching off the receiver before you move the receiver or disconnect any equipment.
It is a necessity that you only use an approved extension and compatible wiring that is suitable for the electrical power consumption of the installed equipment. Please ensure that the electrical power supply corresponds with the voltage on the electrical identification plate at the back of the receiver.
If the receiver does not operate normally even after strictly following the instructions in this user manual, it is recommended to consult your dealer.
1.2 Storage
Your receiver and its accessories are stored and delivered in a packaging designed to protect against electric shocks and moisture. When unpacking it, make sure that all the parts are included and keep the packaging away from children. When transporting the receiver from one place to another or if you are returning it under warranty conditions, make sure to repack the receiver in its original
packaging with its accessories. Failing to comply with such packaging procedures could damage the product and void your warranty.
1.3 equipment Set-up
We recommend you consult a professional installer to set up your equipment. Otherwise, please follow the instructions below:
Refer to the user manual of your TV and antenna.
Make sure that the HDMI cable and outdoor components are in a good condition.
Connect one end of a good quality HDMI cable to the HDMI output on your receiver and the other end to the HDMI input of your TV.
If you use TV SCART connection, use then well shielded SCART cable.
This manual provides complete instructions for installing and using this receiver. The following symbols will serve as follow.
Warning Indicates warning information.
Tips
menu
Indicates any other additional important or helpful information.
Represents a button on the remote control or the receiver. (bold Character)
Move to Represents a menu item within a window. (Italic Character)
1.4 accessories
1 Quick Installation Guide
1 remote control unit
2x batteries (AAA type)
WarnIng: The batteries should not be recharged, disassembled, electrically shortcircuited, be mixed or used with other types of batteries. If rechargeable accumulators instead of batteries are going to be used (e.g. NiMH), we recommend using types with low self-discharge to ensure long time operation of your remote control.
1.5 usage of external uSb devices
It is recommended to use USB 2.0 storage devices or higher. If your device is not compatible to USB 2.0 specifications, recording, playback and other multimedia functions of the receiver might not work properly.
To ensure best performance of your USB storage device please format it via your receiver (through the menu “Media”) to FAT32 system. Other file systems are not
supported by the receiver. However, it is possible to use already NTFS formatted disks.
STRONG cannot guarantee compatibility with all types of USB storage devices.
If you are going to use external USB HDDs (Hard Disk Drives), please consider that power specifications may exceed the supported output of your receiver (max.5 V/800 mA). If so, please connect your USB HDD to an according external power adapter.
It is advised not to store important information on USB storage devices used with the receiver. Always make backups of data on your USB storage device before using it with this receiver. STRONG will not take responsibility for any loss of information or circumstances caused by loss of information.
3
2.0 Your reCeIver
2.1 defaulT pIn: 1234
2.2 front panel
Fig. 1
1. Ir sensor Point your remote control towards this sensor.
2. mode indicator RED indicates that the receiver is in STANDBY mode.
GREEN indicates that the receiver is in OPERATING mode.
3. uSb Connector for USB storage devices.
2.3 rear panel
1. anT In
2. anT ouT
Fig. 2
To connect to your antenna for reception of broadcasted signals.
To connect the terrestrial antenna signal to your TV set. This connection will allow you to watch digital terrestrial programmes depending on the tuner of your TV and local broadcast conditions*
3. S / pdIf Coaxial: To connect your receiver to a digital home theatre, AV receiver or
4. hdmI
5. Tv SCarT
6. audio r/l out
7. power Cord digital audio amplifier.
To connect your receiver with your TV set using an HDMI cable.
To connect your receiver with your TV set using a SCART cable.
To connect your receiver to an analogue audio amplifier.
Your receiver requires a supply voltage of 220~240V AC
(Auto-selectable), 50/60Hz ±5%. Please ensure the local power specification meets these requirements before connecting your receiver to the wall outlet.
4
2.4 remote Control
1. q
2. !
3. pg+/pg-
4. dTv/vCr
5. Info
6. vol+/vol-
7. menu
8. eXIT
9. pq
10. tu
11. ok
Fig. 3
Switches the receiver On/Standby
Mutes all audio outputs of the receiver
Page up/down in all list modes
No function
Opens the current channel information; 2x opens the current event information and 3x the signal information
Increases/decreases the volume level
Opens the main menu, in a menu you will get one step back
Exits from the menu or sub-menu
Menu Off: Change channel to previous/next.
Menu On: Moves the cursor up/down.
Menu Off: Increases/decreases the volume level.
Menu On: Change settings for specific menus
Menu Off: Displays the current channel list
Menu On: Activates the highlighted menu item.
12. reCord
13. TImeShIfT
14. 0~9
15. epg
16. reCall
17. audIo
18. Tv/radIo
19. fav
Records the TV programme to the connected USB storage device
Activates the Timeshift function (Off/On)
Enters a channel number in viewing mode or a value inside the respective menu
Opens the EPG (Electronic Programme Guide) in TV mode
Back to previously watched channel
Opens the audio language selection
Toggles between TV or RADIO mode
Opens the favourite group selection
20. fIle
21. TTX
22. SubTITle
Opens the Media Player list
Displays Teletext on the OSD (On Screen Display)
Shows a list of subtitle languages
23. 5 6 Fast rewind/fast forward
24. Coloured buttons For Multimedia and Teletext functions
3.0 ConneCTIon
3.1 Connecting to a Terrestrial antenna
Fig. 4
To receive broadcasted signals, your terrestrial indoor or outdoor antenna must be connected to the
ANT IN connector on the back of the receiver. Use a properly shielded antenna cable and suitable connectors.
The ANT OUT connector allows you to loop the antenna signal to a second receiver or TV set.
Please consider that the looped signal might be too weak if you use an active antenna.
noTe: If the signals at your location are too weak to receive proper signals with an indoor antenna, we recommend using an outdoor antenna which can be pointed towards the transmission tower. Ask your local dealer for more information.
3.2 Connecting to Tv with hdmI cable
The TV set shall be connected with the receiver using a good quality HDMI or higher cable. This connection gives the highest possible quality.
Fig. 4
3.3 Connecting to Tv with SCarT cable
Fig. 4
Your receiver is also equipped with a SCART connector; alternatively, the TV set can be connected to the receiver using a good quality SCART cable.
5
6
3.4 Connecting to a digital audio amplifier with S / pdIf
Fig. 4
By connecting your receiver to a digital amplifier or home theatre system, you can enjoy the best possible sound quality and multi-channel audio (depending on broadcast). Connect your Digital
Audio Amplifier or home theatre system with a suitable cinch cable to the S / PDIF connector on the back of the receiver.
3.5 Connecting to a digital audio amplifier and Tv using hdmI
Fig. 5
By connecting your receiver to the latest digital amplifiers or Home Cinema systems, you will enjoy the best possible sound quality and multi-channel audio (depending on broadcast). Connect the
HDMI output of the receiver to an input of your amplifier, and then connect the HDMI output of the amplifier to your TV set. Select the correct input on your amplifier to watch and listen to programmes.
3.6 Connecting to an analogue audio amplifier
Fig. 5
Use the 3.5 mm jack to connect your receiver to the analogue input of your Hi-Fi or audio amplifier with a 3.5 mm jack to RCA cable for achieving best possible analogue audio quality.
3.7 Connecting a uSb storage device
Fig. 6 noTe: It is recommended to use USB 2.0 storage devices or higher for recording and play back of TV programmes or HD movies.
noTe: Timeshift/recording and playback only works properly when a fast
USB storage device such as a USB2.0 HDD is connected to the receiver.
Timeshift/recording and playback of HD content requires a sufficient continuous read/write speed of the used USB storage device.
4.0 STarTIng up for The fIrST TIme
When you use your receiver for the first time, the Welcome “Easy install” menu appears. Use pq to move the highlight to the setting you wish to alter and use tu to change values. Start by selecting your language using tu. Once you have selected your language, press q to move the highlight to the next item and use tu to change.
Language
Region:
Subtitle:
Here you can choose your language.
Select your region where this receiver is used.
Select Normal to display subtitles per default, Select Hard of Hearing to show
HoH subtitles per default. Select Off to hide subtitles per default.*
Aspect Mode:
Scan mode:
Connection:
Use this option to select the aspect ratio of your TV and the preferred conversion method. Options are: Auto (automatic detection of aspect ratio),
4:3 Panscan (Displays 16:9 widescreen broadcasts full screen on your 4:3 TV),
4:3 letterbox (black bars on top and under the picture on a 4:3 TV) and 16:9
(use this setting for 16:9 TV sets).
Select All to store scrambled and free to air channels or select Free to store only free to air channels. Note: Scrambled channels cannot be viewed with this receiver.
Use this option to adjust the established connection to your TV set. Select
HDMI or TV SCART.
*Availability of DVB/HoH subtitles depends on the broadcast. If such subtitles are not supported, then most likely subtitles can be activated via Teletext if available.
When all settings have been made, move the highlight to OK and press ok to continue.
noTe: Wrong region selection can lead to missing channels or channels being stored at wrong positions in the channel list.
The receiver will now advance to the Aerial Adjustment screen.
This part of the wizard is of great help when setting up your antenna system.
Use pq to move the highlight to the setting you wish to alter and use tu to change values. The following settings are available:
Antenna Power: Set to On if you use an active antenna. When set to On, 5V will be present at
Beeper:
Channel No.: the ANT IN connector of the receiver. Select Off for passive antennas.
Select On for an audible indication of signal reception. Off turns the beeper off.
Select a channel that is known to carry a broadcast in your region. The Signal
Strength and Signal Quality bars give a visual indication of the reception.
Adjust your antenna to obtain maximum signal strength and quality.
When all settings have been made, press ok to start scanning.
The receiver will search for all available channels now. Once scanning is finished, the receiver switches to viewing mode.
TIp: If the Welcome menu does not appear after switching on the receiver the first time, reset the receiver to factory settings by pressing the menu button and selecting Load Factory Setting in the submenu Tools. (defaulT pIn: 1234)
5.0 QuICk guIde To uSIng Your reCeIver
We at STRONG understand that you can’t wait to enjoy your new high definition digital terrestrial receiver. The following quick guide will make you familiar with the basic operation of this device. We do, however, advice you to read the full manual to get the best performance from your receiver.
To turn your receiver ON or to Standby, use the q button on the remote control.
Choose the desired channel with the pq buttons. Alternatively, you can digit the channel number with the 0~9 buttons on the remote control or press ok in viewing mode to display the channel list.
The volume can be adjusted with the tu buttons.
7
8
6.0 operaTIon
Your new receiver is equipped with several features to make watching TV a true pleasure. This paragraph describes these features. Please also read chapter 7.0 to get familiar with the menu of your receiver.
6.1 Changing channels
Following ways are possible for changing channels with your new receiver:
Via direct access using the 0~9 buttons.
Via the channel list through ok and the pg+/pg- buttons.
Via the pq buttons.
6.1.1 direct access via 0~9 buttons
To gain direct access to a certain channel, simply input its number with the 0~9 buttons on the remote control. Channel numbers can be up to four digits long. Entering a number with less than four digits is possible. Just wait a few seconds and your receiver will switch to the selected channel or press ok immediately after selecting the channel number.
6.1.2 Channel list
Press ok in viewing mode to display the Channel List. Use pq in the channel list to highlight your channel of choice and press ok once to select the highlighted channel. Press ok again to leave the channel list mode. Inside the channel list it is possible to use the pg+/pg- buttons as well in order to scroll page-wise through the list.
TIp: Use tu to toggle between the All Channel list and favourite list(s) or press
fav in viewing mode for a list of available favourite lists.
6.1.3 using the pq
buttons p switches to the next channel.
q switches to the previous channel.
6.2 Info banner
While watching TV you can press the Info button at any time to access current information about the channel and event*. Press Info twice for extended EPG details about the current channel. Press
Info three times for technical details about the current channel.
*Event information is displayed when available. Availability depends on broadcast.
6.3 Selection of audio language
Some channels support a choice of audio formats and/or languages. To select another audio stream, press audIo in viewing mode. A list with available audio streams will now be displayed. Use pq to select the desired stream and confirm with ok. The audio channel as stereo, mono, left and right can be selected with the tu buttons.
6.4 Teletext
Your receiver includes a fully featured Teletext. To access Teletext, press the TTX button in viewing mode and use the 0~9 buttons to input the number of the page you wish to see. The coloured buttons of the remote control allow you to jump to selected pages directly, as indicated on the bottom of the Teletext screen. Use the pq buttons to select one page up or down, use tu buttons to select subpages. Press eXIT or TTX to get back to viewing mode.
6.5 Subtitles
Some channels support a choice of subtitle languages. Press SubTITle in viewing mode to display a list of available subtitle languages. Select your subtitle of choice with pq and press ok to confirm.
Press eXIT to leave without making changes.*
* Availability of DVB/HoH subtitles depends on the broadcast. If such subtitles are not supported, then most likely subtitles can be activated via Teletext if available.
6.6 Timeshift
Timeshift allows you to pause live broadcasts and resume playback later. To activate this function set the Timeshift mode in the DVR Setting menu to on by selecting Pause. For details, see 7.6.3. Press
pauSe in viewing mode to activate Timeshift. The progress information banner appears on screen.
Live TV keeps playing for moment and will then pause. Press u to resume Timeshifted playback. Press
STop to return to live TV.
noTe: Timeshift and its playback only work properly when a fast USB storage device such as a USB2.0 HDD is connected to the receiver. Timeshift and playback of HD content requires sufficient read/write speed of the used
USB storage device.
6.7 epg (electronic programme guide)
The Electronic Programme Guide is a very useful function that allows you to view event schedules and programme information and to mark events/movies for recording. To access the EPG, press the
epg button in viewing mode. Use pq to select a channel and tu to select an event. Press ok to display detailed information of the selected event. Use eXIT to quit the detailed information screen.
Press red to access further step functions. Use tu to select the desired step and ok to execute it.
Press eXIT to quit the step function. Press green to set a timer for a selected event. Refer to section
7.3.4 for details of the timer function.
noTe: Availability of EPG data depends on broadcast.
6.8 Instant recording
Your new receiver allows you to make an instant recording of the programme you are watching.
Simply press reCord to start the recording. To enter the duration for the recording, press reCord again. Use the 0~9 buttons to enter the recording time and press ok to confirm.
9
At the beginning of the recording a recording sign will be shown for a short while on the upper left corner of your TV screen. To stop the recording, press STop. Select Yes and press ok again to stop the recording. It is possible to make 2 recordings at the same time if they are broadcasted on same frequency.
You can access the Record Manager via the fIle button, and select Record by pressing the button 1.
See chapter 7.6.1 for details.
*Please connect a USB storage device with sufficient free space before you start a recording.
7.0 maIn menu
The main menu gives you access to settings, multimedia functions and games. To access the main menu, press menu in viewing mode. The main menu consists of the following sub menus: Edit
Channel, Installation, System Setup, Tools, Games and Media.
Throughout the main menu, menu or eXIT can be used to get back to the previous screen.
7.1 edit Channel
Use pq to select Edit Channel and press ok or u to enter.
Use pq to highlight the submenu of choice and press ok to select.
Press eXIT or t to get back to the main menu.
7.1.1 Tv Channel list
In Edit Channel menu select TV Channel List with pq and press ok to enter.
Use tu to change the channel group (assumed you have already set up favourite groups).
Select the channel of choice with pq. Press ok to view the selected channel in the preview box.
7.1.1.1 adding channels to favourite lists
Channels from the TV Channel List can be added to up to 8 different favourite groups. Press fav in TV
Channel List to access this function. The FAV sign on the top of the screen will move up to indicate that the favourite function is selected. Use pq to select a channel you wish to add to a favourite group.
When the highlight is on the channel of your choice, press ok. A list with all available favourite lists will now pop up. Use pq to select the favourite list you wish to add the channel to and press ok, press eXIT to finalize the process. Favourite channels will be marked with a heart symbol. When all changes have been made, press eXIT twice. A confirmation banner will pop up. Select Yes to save the changes or No to discard.
7.1.1.2 locking channels
Locked channels can only be watched after entering the PIN code. (defaulT pIn: 1234)
To lock or unlock a channel, press red while in TV Channel List. Press pq to select a channel and press ok to lock or unlock it. You are asked to input the PIN code. (defaulT pIn: 1234 Locked channels will be marked with the loCk symbol. Locking/unlocking multiple channels in one session is possible. When all changes have been made, press eXIT twice. A confirmation banner will pop up.
Select Yes to save the changes or No to discard.
10
7.1.1.3 Skipping channels
Channels marked with Skip will be skipped when zapping channels with the pq buttons. The channels will still be available from the channel list.
To mark channels for skipping, press green while in TV Channel List. Use pq to select a channel and press ok to mark or unmark it for skipping. Channels set for skipping will be marked with the
symbol. When all changes have been made, press eXIT twice. A confirmation banner will pop up.
Select Yes to save the changes or No to discard.
7.1.1.4 moving channels
To enable the Move function, press YelloW while in TV Channel List. Use pq to select a channel and press ok to select it. Now you can move the selected channel up or down inside the channel list by using pq. When the channel is on the position of your choice, press ok again. The channel is now fixed on its new position. When all changes have been made, press eXIT twice. A confirmation banner will pop up. Select Yes to save the changes or No to discard.
7.1.1.5 editing channels
The Edit function allows you to Sort, Rename or Delete channels. To enter the Edit menu, press blue while in TV Channel List. The Edit Channel menu will appear.
If you made changes in the previous menu, but haven’t saved them yet, you will be asked to do so now.
Sort
Press red to enter the Sort menu.
Use pq to select sorting method and press ok to confirm.
Possible methods are:
Name (A-Z):
Name (Z-A):
Free/Scramble:
Lock:
Default:
Sorting in alphabetical order from A to Z.
Sorting in alphabetical order from Z to A.
First in the list will be Free-To-Air channels.
All unlocked channels will placed first in the list.
Sorting by searched Order (from lowest to highest frequency or by LCN numbering).
rename
Press green in Edit Channel to enable the Rename function. The Rename sign will move up to indicate that Rename is selected. Use pq to highlight a channel and press ok to select it. A text field will now pop up at the right of the screen. Use tu pq to select characters and enter them with
ok. When you have finished editing, press blue to enter the changes. When all changes have been made, press eXIT twice. Select Yes to save the changes or No to discard.
delete
Press blue in Edit Channel to enable the Delete function. The Delete sign will move up to indicate that Delete is selected. Use pq to highlight a channel and press ok to mark it for deletion. When you have marked all channels you wish to delete, press eXIT twice. A confirmation banner will be displayed. Select Yes to delete the marked channels or No to cancel.
11
7.1.2 radio Channel list
Basically, the operation of the Radio Channel List is the same as in the TV Channel List. The only difference is that in Radio Channel List there is no video information, so it will always display the radio background on the preview screen.
7.1.3 delete all
Use this menu to delete all stored channels. Select Delete All with pq and press ok. The receiver asks you to enter the pin code. (defaulT pIn: 1234). Inside the confirmation window select Yes with tu and press ok to delete or select No to cancel.
favourite lists from your receiver, and you are not able to leave the menu until you search for channels again.
7.1.4 rename favourite list
This menu allows you to personalize the names of the 8 available favourite lists.
Use pq to select Rename Favourite List from the Edit Channel Menu and press ok to proceed. The names of all groups are now displayed. Select a favourite group with pq and press ok to edit its name. A text field will now pop up at the right of the screen. Use tu pq to select characters and enter them with ok. When you have finished editing, press blue to save the changes. When all changes have been made, press eXIT twice to leave this menu.
7.2 Installation
7.2.1 auto Scan
Use pq to select Installation and press ok or u to advance.
Select Auto Scan with pq and press ok to enter.
Use tu to toggle between Yes or No. When FTA Only is set to Yes, scrambled channels won’t be stored in the channel list. Use pq to highlight Search. Now press ok to start auto scan.
The receiver will store all found channels in the channel list.
7.2.2 Channel Scan
Use pq to select Installation, press ok or u to advance.
Use pq to select Channel Scan and press ok to enter.
Use tu to toggle between available scan modes: By Channel and By Frequency.
If By Channel is selected, use the cursor buttons to select Scan Band and Channel No. If By Frequency is selected, use the cursor buttons to select Frequency and Bandwidth. Highlight Search and press ok to start scanning. Newly found channels will be added to the channel list.
7.2.3 antenna power
Use pq to select Installation, press ok or u to advance.
Use pq to select Antenna Power and press ok to enter.
Set to On if you use an active antenna.
12
Select Off for passive antennas.
When set to On, 5V will be present on the ANT IN connector of the receiver.
Press eXIT to leave the Antenna Power menu.
Tip When a passive antenna is used, set the Antenna power to Off.
7.2.4 lCn (logical Channel numbering)
If LCN (Logical Channel Numbering) is activated and an LCN signal is provided by the operator, channels will be stored in an operator defined order. Set LCN to On to activate operator defined channel numbering or Off to store channels in found order. This function only applies when a new channel search is performed.
7.3 System Setup
This menu allows you to manage the system settings of your receiver. It consists of the following sub-menus: Language, TV System, Local Time Setting, Timer Setting, Parental Lock, OSD Setting and Auto
Standby.
Press pq to highlight the menu of choice and press ok advance to the next screen. Use pq to move the highlight to the setting of choice. Values can be changed with tu. Press eXIT to leave.
7.3.1 language
This menu allows you to set up your language preferences.
Language: Use tu to select the language for the On Screen Display.
First Audio:
Second Audio:
Teletext:
Subtitle:
Use tu to select Audio language.
Use tu to select a language that will be played when the language selected at First Audio isn’t available.
Subtitle Language: Use tu to select the preferred subtitle language.
2nd Subtitle Language: If the first subtitle language is not available, this language will be used next.
Use tu to select the preferred Teletext language (when available).
Use tu to select the preferred subtitle type to be displayed automatically.
Select Normal, Hard of Hearing or Off*
* Availability of DVB/HoH subtitles depends on the broadcast. If such subtitles are not supported, then most likely subtitles can be activated via Teletext if available.
7.3.2 Tv System
Use this menu to match your receiver to your TV set. The following settings are available:
Video Resolution:
Aspect Mode:
Use this option to select the video resolution of your TV screen. Options are:
By Source (automatic detection of video resolution offered to the receiver),
By Native TV (automatic detection of maximal resolution of TV screen), and manual selections 480i, 576i up to 1080p Please use a setting that matches your TV’s specifications. After a selection is made, you will be asked to confirm. Selection above 576i is only applicable on HDMI output.
Use this option to select the aspect ratio of your TV and the preferred conversion method. The options are: Auto (automatic detection of aspect ratio), 4:3 Panscan (Displays 16:9 widescreen broadcasts full screen on your
13
Connection:
4:3 TV), 4:3 letterbox (black bars on top and under the picture on a 4:3 TV) and
16:9 (use this setting for 16:9 TV sets).
Use this option to select the connection to your TV set. Select HDMI or TV
SCART. If connection type HDMI is selected, then only the CVBS signal is available on the TV SCART.
Digital Audio Output: Toggles between PCM and Bitstream output. When PCM is selected, all digital audio will be converted to stereo audio. Bitstream enables you to listen or transfer Dolby® Digital/ Dolby® Digital Plus* audio to the TV via HDMI or to a
Home entertainment system (for example) through coaxial S / PDIF.
*Dolby and the double-D symbol are registered trademarks of Dolby Laboratories
7.3.3 local Time Setting
Here you can set up your region and time zone.
Region:
GMT Usage:
Use tu to select the region you live in.
Set to By Region for broadcaster defined time, User Define to select manual a
GMT zone or to Off to input time and date manually.
Allows you to adjust the time zone you live in. This option is only available GMT Offset: when GMT Usage is set to User Define.The GMT Offset range is “-11:30 ~
+12:00”, increasing by half hours progressively. The cities matching the set
Daylight Saving:
GMT Offset are displayed at the bottom of the screen.
Select Off or On to add one hour extra for summer time during the summer.
Date and Time settings are available only when GMT Usage is set to Off. Use the 0~9 buttons to enter the date. Press eXIT to proceed.
Time Display the 0~9 buttons to enter the time. Press eXIT to proceed.
Select On to display time on screen, Off to remove.
7.3.4 Timer Setting
This menu allows you to set up to 8 timed events for recording or waking up the receiver.
Use pq to select Timer Setting from the System Setup menu and press ok to enter.
The receiver will display a list with 8 timers, followed by their respective status. Select the timer you wish to set or change with pq and press ok to proceed.
The timer setup menu will now be displayed.
The following settings are available:
Timer Mode: Choose between Off (Timer inactive), Once, Daily (Timer will be executed every day, same time) or Weekly (Timer will be executed every week, same day, same time) and Monthly (Timer will be executed every month, same day, same time).
Choose between Channel (Timer will wake up the receiver) or Record (Timer Timer Service:
Wakeup Channel:
Wakeup Date: will start to record the scheduled event).
Use tu to select the channel the timer will wake up with.
Use the 0~9 buttons to input the date for the timed event.
Wakeup Time:
Duration:
Use the 0~9 buttons to input the start time.
Use the 0~9 buttons to input the timer duration.
When all settings are according to your wishes, use pq to move the highlight to Save and press ok to confirm. To quit the timer without saving your settings, move the highlight to Cancel.
14
7.3.5 parental lock
This menu allows you to protect the installation menu and/or channels with a PIN code. You can also enter a new PIN code in the Parental Lock menu.
Use pq to select Parental Lock from the System Setup menu and press ok to proceed. You will be asked to enter your PIN code. (defaulT pIn: 1234)
Menu Lock:
Parental Rating:
Locks the installation menu. You can set Menu Lock to On or Off.
Choose between: Off, 4 years and up to 18 years. Channels with a parental rating above the chosen age will be protected with a PIN code (if available in
New Password:
Confirm Password: your local broadcast.)
Enter your new PIN code (4 digits) here.
Re-enter your PIN code here to confirm.
7.3.6 oSd Setting
This menu allows you to change settings for: OSD Timeout and OSD Transparency.
OSD Timeout: Sets the time after which on screen banners and messages disappear. The range is 1~10 seconds or Always On.
OSD Transparency: To set the OSD transparency from Off ~ 40% with 10% steps.
Load Default OSD Setting:
Press ok to clear all OSD settings and reset to default values.
7.3.7 auto Standby
Auto Standby is a new feature that helps you reducing power consumption. When set to 30Min/1
Hour/2 Hours or 3 Hours, the receiver will switch to standby if it doesn’t receive any commands during this time. Set Auto Standby to Off to deactivate the automatic standby function.
7.4 Tools
Press menu in viewing mode to enter the Main Menu.
Select the Tools submenu with pq and press ok or u to enter.
Use pq to highlight the submenu of choice and press ok proceed.
Press eXIT to leave.
7.4.1 Information
This submenu shows receiver specific information such as hardware version and software version.
Please have the Information screen on hand when you call our hotline. The person who answers your call might ask for the information given in this screen.
7.4.2 load factory Settings
This option allows you to reset the receiver to factory settings, which clears all stored channels.
channels will be permanently deleted. Please use this option with care.
Use pq to select Load Factory Settings in the Tools menu and press ok. You are asked to input your
PIN code.
15
Input the correct PIN code using the 0~9 (defaulT pIn: 1234). A confirmation window is displayed.
Select Yes to return to factory settings. Select No to cancel.
Press eXIT to leave.
7.4.3 S/W upgrade by oTa
This receiver is equipped with an Over The Air software upgrade function. An Over The Air update might not be available in your region. Please visit our website www . strong . tv or contact your local service hotline for more information about this option.
7.4.4 upgrade by uSb
This feature allows you to upgrade receiver software via the USB port. When new software is available for your receiver, it can be downloaded from our website www . strong . tv.
Place the software file (unzipped) in the root directory of your USB storage device (HDD, memory stick etc.) and connect the device to the USB port of the receiver.
Select Upgrade by USB from the Tools menu and press ok to proceed.
The upgrade menu will now be displayed.
Use pq to select Upgrade Mode and choose option Allcode.
Use pq to select Upgrade File and choose the file containing the latest and correct software.
Once all settings are made, move the highlight to Start and press ok to start the upgrade process.
After a few seconds, the receiver asks: “Are you sure to burn flash?”. Select Yes to finalize the upgrade or No to quit without upgrading.
way, please perform a factory reset as well. See chapter 7.4.2.
process NEVER disconnect the receiver from the mains or switch off the power! Doing so might damage your receiver and will void warranty!
7.5 games
Your receiver is equipped with two games which can be played on your TV screen using the receiver remote control.
Use pq to select Games from the main menu and press ok or u to proceed.
Select one of the available games (Othello or Sudoku) using pq and press ok to start the game.
Follow the directions on screen. Press eXIT to quit a game.
7.6 media
The Media menu consists of the following submenus: Media Player, HDD Information, DVR Setting and
Remove USB device safely.
Use pq to highlight the menu of choice and press ok to enter. Press eXIT to quit.
16
5:
6:
7:
7.6.1 media player
This function allows playback of different kind of files from the connected USB storage device. In the
Media menu, select Media Player and press ok to enter this menu.
When entering the media player, the highlight is on the USB storage device. Press q and ok to open the directory respectively its folders/subfolders.
First select which files you like to play back. Use the button 1 to switch between Video/Record/
Music or Image. Press pq to select a file or folder and then press ok to open the folder/subfolder (if applicable) or start playback of the file. Press the eXIT button to exit.
Use the buttons like described below in order to choose functions during the different playback modes (like described in the help banner below): video:
Info:
1:
2:
7:
Press the Info button to set repeat mode. The options are repeat folder
folder icon/repeat once 1 or no repetition (no icon shown).
During the playback of a movie with external subtitles, press 1 to enter the subtitle menu. In this menu you can select size and colours of your preference.
Press the button 2 to open the Sort menu. You can sort by Name/Time or Size.
Press the button 7 to open the Edit menu. This menu allows accessing the following functions by entering the number: rename 4, copy 5, delete 6, create folder 7.
One step back or leave the folder and quit the function.
eXIT: record:
2:
3:
4:
Press 2 to enter a new name for the selected recording.
Highlight the recording that you want to lock. After pressing 3 you will be asked to input your PIN code. defaulT pIn: "1234”. After entering your PIN code, the recording is locked. If you want to unlock the recording again, press
3 again.
Press 4 to mark the recording you want to delete. By selecting the same recording and pressing 4 again you can remove the delete marker again.
Press eXIT to delete.
One step back or leave the folder and quit the function.
eXIT: music:
4: Press 4 to open a previously created play list. Then you can select the music file that you want to add your play list by pressing 5 (a single file will be added to the play list) or 6 (all files of this directory/folder will be added to the play list).
Press 5 to add a file to the playlist. A favourite icon will be shown next to the file.
Press 6 to add all files of this directory/folder to the play list. Press 6 again to delete all files from the play list.
Press 7 to open the Edit menu. This menu allows accessing the following functions by entering the number: rename 4, copy 5, delete 6, create folder 7.
17
2:
Info:
eXIT:
Image:
4:
Press button 2 to open the sort window. You can sort by Name/Time/Size and
Favourite.
Press the Info button to set repeat mode. The option is Repeat Folder/
Random Folder/Repeat One.
One step back or leave the folder and quit the function.
5:
6:
7:
2:
Info:
3:
eXIT:
Press 4 to open a previously created play list. Then you can select the image file that you want to add your play list by pressing 5 (a single file will be added to the play list) or 6 (all files of this directory/folder will be added to the play list).
Press 5 to add a file to the play list. A favourite icon will be shown next to the file.
Press 6 to add all files of this directory/folder to the play list. Press 6 again to delete all files from the play list.
Press 7 to open the Edit menu. This menu allows you to accessing the following functions by entering the desired number: rename 4, copy 5, delete
6, create folder 7.
Press button 2 to open the sort window. You can sort by Name/Time/Size and
Favourite.
Press Info to access slideshow settings. You can change the slide time and slideshow repetition.
Press 3 to show the files in a preview of 3x3 pictures.
One step back or leave the folder and quit the function.
7.6.2 hdd Information
This option shows relevant information about the connected USB device. In this menu you can also format your USB storage device and setup the recording type.
Select HDD Information in the Media menu and press ok to enter.
Now you will see all details as Free and used Recording Sizes and used file system.
Press the YelloW button Format to format the connected USB device.
Please, enter your PIN code to access this menu and press ok to start formatting.
Warning: device. Please make a backup copy of all data you wish to keep before entering the HDD Format menu. STRONG cannot be held responsible for loss of data from USB devices used with this receiver.
Press ok to proceed, select FAT or Cancel, or press eXIT to leave without formatting.
noTe: It is possible to use USB storage devices already formatted in NTFS.
Press eXIT to leave this menu.
18
7.6.3 dvr Setting
This menu allows you to configure settings for Timeshift, recording and playback.
Select DVR Setting in the Media menu and press ok to enter.
Use pq to move the highlight and tu to change settings.
Timeshift: Select between Auto, Pause or Off. When Timeshift is set to Auto it will automatically start every time after tuning to a channel. When Timeshift is set to Pause it will start only after pressing the YelloW/pauSe button. Select Off to deactivate Timeshift.
during playback of recorded files. This will only work when the info banner is displayed on screen. If it is not, press Info.
Time Shift to Record: If set to On the timeshifted part will be included in your recording when you start to record the current programme.
PS Record: Select between On or Off. When Off is selected, recordings will also include subtitles and Teletext (when available). Record to PS mode On allows recordings without these extras which will need less space on your USB device.
Press eXIT to leave this menu.
7.6.4 remove uSb device safely
Select Remove USB device safely from the tools menu and press ok. The receiver will display a message indicating that you can safely remove your storage device from the receiver.
noTe: After performing this function, the USB device is no longer accessible from your receiver. To gain access to your storage device again, re-insert it or switch the receiver to standby and on again.
8.0 TroubleShooTIng
There may be various reasons for abnormal operation of the receiver. Check the receiver according to the procedures shown below. If the receiver does not work properly after checking it, please contact your dealer or the local Service Hotline. Do NOT try to open or disassemble the receiver. It may cause a dangerous situation and warranty will be void.
problem
LED indicator not lit
No signal found possible cause
Mains lead unplugged
Aerial is disconnected
Aerial is damaged/misaligned
Out of digital signal area
Active antenna requires to switch ON antenna power/ external power
What to do
Check mains plug
Check aerial lead
Check aerial
Check with dealer
Switch receiver’s Antenna
Power ON/connect external power
19
problem
No picture or sound on TV or amplifier possible cause
HDMI or SCART is not selected on your TV or amplifier or the unit is set to higher resolution as the TV supports.
TV/amplifier is not switched on
What to do
Switch to correct TV/amplifier input
Select lower resolution on receiver
Switch TV/amplifier on.
Check if S / PDIF connection is used.
Select alternative channel Scrambled channel
Message
Channel is scrambled
No response to remote control Receiver off
Remote not aimed correctly
Front panel obstructed
Remote batteries exhausted
Forgotten PIN code
Forgotten channel lock code
After moving the receiver to another room/area you are no longer able to receive digital reception
Antenna signals are too weak
The signal strength/quality might be less than before, if using an indoor antenna.
The receiver switches off automatically.
Playback of video (or Timeshift) is causing picture freeze/macro blocks or similar distortion, especially on HD content.
Auto Standby function enabled.
Read/write speed of your USB device could be too low.
9.0 TeChnICal SpeCIfICaTIonS
demodulator
Demodulator:
Transmission mode:
COFDM; 16 QAM/64 QAM, QPSK
2 K - 8 K
Plug in and turn on plug
Aim remote at front panel
Check for obstructions
Replace remote batteries
Default PIN is 1234
Contact local Service Hotline or send email to our Support via www . strong . tv
Press the INFO button on remote 3x to call up signal bars and adjust antenna for
(maximum) reception or rescan channels
When using an active antenna, check antenna power.
Try to use an outdoor antenna.
Disable auto standby. See section 7.3.7 for details.
Make sure to use a USB storage device with sufficient speed and space. Pen drives (‘USB sticks’) may not support sufficient speed.
video decoder
Profile level:
Video resolutions:
20
MPEG-2 MP@ML, AVC/[email protected], MPEG4 ASP supported
480i / 480p / 576i / 576p / 720p / 1080i / 1080p / By Native TV /By source
Decoding & Video out:
Aspect ratio:
PAL
4:3 Letterbox, 4:3 Pan & Scan, 16:9, Auto audio decoder
Audio support:
MPEG MusiCam Layer II
Sampling rate:
Audio mode:
HE-AAC/Dolby Digital /Dolby Digital Plus*/AC3/PCM
32, 44.1, 48 KHz
Stereo, Mono
*Dolby and the double-D symbol are registered trademarks of Dolby Laboratories
Tuner
Front End:
Input frequency range:
DVB-T, UHF & VHF Tuner
174 – 230 MHz (VHF) and 470 - 862 MHz (UHF)
Loop through frequency range: 47 - 862 MHz
Input signal level: -20 ~ -84 dBm memory and System
Flash memory:
SDRAM:
4 Mbytes
64 Mbytes multimedia
Video playback:
Audio playback:
Picture view:
MPEG-1 and MPEG-2 encoded (mpg), VOB, AVI, MKV, TS, M2T,
M2TS, MPEG-4 and MOV*
MP3 and OGG*
BMP and JPEG*
*STRONG cannot guarantee the playback of files although extensions are listed, as it depends on codec used, data bit rate and resolution (all MPEG codec formats are supported).
Connectors
ANT IN - IEC Female
ANT OUT - IEC Male
TV SCART (RGB, CVBS, Audio L&R)
HDMI
S / PDIF (coax.)
3.5 mm stereo audio jack (audio left/right)
USB 2.0 port: 5 V/800 mA (max.) supported general data
Supply Voltage: 220 - 240 V AC (SMPS), 50/60 Hz
Power Consumption: 3.06 W (typ.), 12.00 W (max)
Power consumption in Standby: 0.40 W
Operating Temperature:
Storage Temperature:
0 ~ +40° C
-30 ~ +80° C
.
Operating Humidity Range:
Size (WxDxH) in mm:
Net-weight:
10~85%, RH, Non-condensing
147 x 122 x 35
0.24 kg
21
22
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project