advertisement
▼
Scroll to page 2
of 12
EN Instructions for use / assembly instructions DE Gebrauchsanleitung / Montageanleitung 2 3 Cento XXL 14811000 English Symbol description Safety Notes Gloves should be worn during installation to prevent crushing and cutting injuries. Do not use silicone containing acetic acid! The hot and cold supplies must be of equal pressures. Adjustment (see page 6) Installation Instructions • Prior to installation, inspect the product for transport damages. After it has been installed, no transport or surface damage will be honoured. To adjust the hot water limiter. Using a hot water limiter in combination with a continuous flow water heater is not recommended. Operation (see page 7) • The pipes and the fixture must be installed, flushed and tested as per the applicable standards. • Do not rotate the spout further than 360º or damage to the hose will result. • The plumbing codes applicable in the respective countries must be oberserved. • Hansgrohe recommends not to use as drinking water the first half liter of water drawn in the morning or after a prolonged period of non-use. Technical Data This mixer series-produced with EcoSmart® (flow limiter) Operating pressure: max. 1 MPa Recommended operating pressure: 0,1 - 0,5 MPa Test pressure: 1,6 MPa (1 MPa = 10 bar = 147 PSI) Hot water temperature: max. 70°C Recommended hot water temp.: 65°C Thermal disinfection: max. 70°C / 4 min The product is exclusively designed for drinking water! Dimensions (see page 8) Flow diagram (see page 8) Normal spray with EcoSmart® ® Normal spray without EcoSmart Regular with EcoSmart® ® Regular without EcoSmart Cleaning (see page 9) and enclosed brochure Maintenance (see page 9) The check valves must be checked regularly according to DIN EN 1717 in accordance with national or regional regulations (at least once a year). Spare parts (see page 10) 2 Assembly see page 4 Deutsch Symbolbeschreibung Sicherheitshinweise Bei der Montage müssen zur Vermeidung von Quetsch- und Schnittverletzungen Handschuhe getragen werden. Große Druckunterschiede zwischen den Kalt- und Warmwasseranschlüssen müssen ausgeglichen werden. Montagehinweise • Vor der Montage muss das Produkt auf Transportschäden untersucht werden. Nach dem Einbau werden keine Transport- oder Oberflächenschäden anerkannt. • Die Leitungen und die Armatur müssen nach den gültigen Normen montiert, gespült und geprüft werden. • Die in den Ländern jeweils gültigen Installationsrichtlinien sind einzuhalten. Technische Daten Kein essigsäurehaltiges Silikon verwenden! Justierung (siehe Seite 6) Einstellen der Warmwasserbegrenzung. In Verbindung mit Durchlauferhitzern ist eine Warmwassersperre nicht zu empfehlen. Bedienung (siehe Seite 7) • Auslauf nicht weiter drehen als 360º, da sonst der Schlauch beschädigt werden kann. • Hansgrohe empfiehlt, morgens oder nach längeren Stagnationszeiten den ersten halben Liter nicht als Trinkwasser zu verwenden. Armatur serienmäßig mit EcoSmart® (Durchflussbegrenzer) Betriebsdruck: max. 1 MPa Empfohlener Betriebsdruck: 0,1 - 0,5 MPa Prüfdruck: 1,6 MPa (1 MPa = 10 bar = 147 PSI) Heißwassertemperatur: max. 70°C Empfohlene Heißwassertemperatur: 65°C Thermische Desinfektion: max. 70°C / 4 min Maße (siehe Seite 8) Das Produkt ist ausschließlich für Trinkwasser konzipiert! Reinigung (siehe Seite 9) und beiliegende Broschüre Durchflussdiagramm (siehe Seite 8) Normalstrahl mit EcoSmart® ® Normalstrahl ohne EcoSmart Brausestrahl mit EcoSmart® ® Brausestrahl ohne EcoSmart Wartung (siehe Seite 9) Rückflussverhinderer müssen gemäß DIN EN 1717 regelmäßig in Übereinstimmung mit nationalen oder regionalen Bestimmungen (DIN 1988 einmal jährlich) auf ihre Funktion geprüft werden. Serviceteile (siehe Seite 10) Montage siehe Seite 4 3 1b 2 max. 70 max. 35 1a 3 3 Nm 4 5 1. SW 10 mm SW 24 mm 4 Nm 2. 4 6 7 8 9 > 2 min 10 1 Nm 5 Justierung 60 °C 10 °C 1 2 4 5 0,3 MPa 3 + 6 6 7 cli ck open / öffnen close / schließen hot / warm 1. 2. cold / kalt open / öffnen 7 314 600 360° 187 max. 70 202 Ø 29 14 7 101 830 Ø 50 117 Ø 34 270 G 1/2 1 2 3 4 8 Reinigung 1 2 Wartung 1 2 9 97475000 97662000 97735000 98387000 (17x2,5) 97558000 97350000 96338000 98193000 (32x2) 98231000 (18x1,5) 92602000 (20x2,5) 92204000 98459000 98205000 (21x2) 95498000 97209000 (M37x1,5) 98140000 SW 30 mm (20x1) 95140000 (M4x20) SW 4 mm 95008000 95730000 97489000 (900 mm) SW 24 mm 97523000 97548000 95049000 10 95910000 11 Prüfzeichen P-IX 12 SVGW ACS WRAS ETA X Hansgrohe · Auestraße 5 – 9 · D-77761 Schiltach · Telefon +49 (0) 78 36/51-1282 · Telefax +49 (0) 7836/511440 E-Mail: [email protected] · Internet: www.hansgrohe.com 02/2017 9.02795.03 14811000 DVGW
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement