advertisement
USB Serial Converter
User’s Manual
Copyright Statement
No part of this publication may be reproduced in any form by any means without the prior written permission. Other trademarks or brand names mentioned herein are trademarks or registered trademarks of their respective companies.
Disclaimer
Information in this document is subject to change without notice. The manufacturer does not make any representations or warranties (implied or otherwise) regarding the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any commercial damage, including but not limited to special, incidental, consequential, or other damage.
March 2007, Rev 5.0 i
Safety Instructions
Always read the safety instructions carefully
Keep this User’s Manual for future reference
Keep this equipment away from humidity
If any of the following situation arises, get the equipment checked by a service technician:
• The equipment has been exposed to moisture.
• The equipment has been dropped and damaged.
• The equipment has obvious sign of breakage.
• The equipment has not been working well or you cannot get it work according to User’s Manual. ii
Table of Contents
iii
1. Introduction
1. Introduction
How to find a lightest way to contact your PDA to the USB port on your PC? USB
Serial Converter operates as a bridge between one USB port and standard RS-232
Serial port. You just easily hook the cable into PC or Hub’s port, and it can connect any RS-232 devices, such as PDA, scanner, printer…etc.
Features
Compliant with the USB 1.1 version specification
Supports RS-232 serial Interface
Supports 500 kbps data transfer rate
USB suspend condition
Plug & Play compatible
USB host device drivers available
Draws its power from USB connection – no extra power adapter required
Supports Windows 98SE, ME, 2000, XP, Vista 32/64-bit and Mac10.x
Package Contents
Before installation, please check the items of the package.
USB Serial Converter x1
Driver x1
Quick Installation Guide x1
System Requirements
IBM compatible computer or Mac
Windows 98SE, ME, 2000, XP, Vista 32/64-bit, Mac 10.x
Available USB port
64 MB RAM or more.
Pentium 233 MHz or higher
1
USB Serial Converter User’s Manual
2. Installation
On Windows Vista
1. Connect the USB Serial Converter to the USB port on your computer.
software (recommended).
3. Insert the provided CD into your CD-ROM drive and click Next. (Sometimes the installer will automatically proceed to next step.)
2
4. When the installation is done, click Close.
2. Installation
5. A pop-up message will appear in the notification area indicating the installation is complete. Restart your computer if prompted to do so.
3
USB Serial Converter User’s Manual
On Windows 98SE/ME/2000/XP
Note: DO NOT connect the USB Serial Converter to your computer before completing the driver installation.
1. Insert the provided CD into your CD-ROM drive. Run the Setup file under
x:\Driver\Win98_XP where x: is your CD-ROM drive letter. When the welcome screen appears, click Next.
2. When the following screen appears, click Finish.
Once the installation is done, connect the converter to a free USB port on your computer.
4
2. Installation
Verify the Driver Installation on Windows
To verify your converter installation, please launch Device Manager by the steps below:
On Windows 98SE/ME/2000/XP: Right-click the My Computer icon on the desktop and select Properties > System > (Hardware) > Device Manager.
On Windows Vista: Right-click the Computer icon on the desktop and select
Properties > Device Manager.
In the Ports (COM & LPT) group, a string similar to USB to Serial Port or Prolific
USB to Serial Comm Port should be displayed.
If there is a question or exclamation mark next to that item, then the driver is not properly installed. Please delete the item and repeat the installation steps.
Windows 98SE/ME
Windows 2000/XP/Vista
5
USB Serial Converter User’s Manual
On Mac OS X
The provided Mac X driver supports:
Mac OS 10.1 and above for PowerPC based Mac
Mac OS 10.4 and above for Intel based Mac
To install the drivers:
1. Insert the provided driver CD into your CD-ROM drive. Double-click the CD icon on the desktop and navigate to the directory of \Driver\MacX. Copy and then paste the PL2303_1.2.1r2.dmg file to the desktop.
2. Double-click the dmg file on the desktop to extract the file. Then double-click the PL2303_1.2.1 file that is extracted.
3. When the welcome screen appears, click Continue.
6
4. Select a destination disk to install the driver and click Continue.
2. Installation field and click OK.
7
USB Serial Converter User’s Manual
9. Connect the converter to a free USB port on your Mac.
10. To verify the installation: Go to Apple System Profiler > Extensions and you should find ProlificUsbSerial among the list. This means the installation is successfully done.
Connecting Serial Device
Now you can connect your RS-232 device to the converter. If prompted to install the driver for your serial device, follow the manual that comes with your serial device to complete the installation.
8
3. Specifications
3. Specifications
Data Transfer Rate
Function
Ports
Power
500 kbps
USB1.1 Serial Converter operates as a bridge between one USB port and standard RS-232 serial port
USB 1.1, USB Type A male
Bus-powered
Operating System Support Windows 98SE, ME, 2000, XP, Vista 32/64-bit
Mac 10.x
Accessories Driver CD, Quick Installation Guide
* Specification is subject to change without further notice.
9
USB Serial Converter User’s Manual
4. Regulatory Compliance
FCC Conditions
This equipment has been tested and found to comply with Part 15 of the FCC
Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received. Including interference that may cause undesired operation.
CE
This equipment is in compliance with the requirements of the following regulations:
EN 55 022: CLASS B
10
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project