Samsung R21 Specifications

SAMSUNG Home Appliance Service
For the latest parts information,
please access to our service web site
(http://www.e4buyer.com/refrigerator)
SIDE-BY-SIDE REFRIGERATOR
Model:
RS21**
RS23**
WARNING
IMPORTANT SAFETY NOTICE
The service guide is for service men with adequate backgrounds of
electrical, electronic, and mechanical experience. Any attempt to repair
a major appliance may result in personal injury and property damage.
The manufacturer or dealer cannot be responsible for the interpretation
of this information.
SAMSUNG ELECTRONICS
Technical Service Guide
Copyright ⓒ2002
All rights reserved. This service guide may not be reproduced in whole or in
part in any form without written permission from the SAMSUNG ELECTRONICS
Company.
3
Contents
1. SAFETY WARNINGS ·······································5
2. INSTRUCTION ···········································8
3. INSTALLATION ···········································9
4. NOMENCLATURE
········································10
5. SPECIFICATIONS·········································11
6. INTERIOR VIEWS AND DIMENSIONS ···························14
7. FREEZING CYCLE AND COOL AIR CIRCULATION ROUTE·············19
8. MECHANICAL DISASSEMBLY
································21
9. FUNCTIONS AND OPERATION
10. CIRCUIT DESCRIPTION
·······························29
···································43
11. DIAGNOSIS AND TROUBLESHOOTING ·························52
●
APPENDIX Ⅰ (REFERENCE FOR CIRCUIT DIAGNOSTICS)
●
APPENDIX Ⅱ (CIRCUIT DIAGRAM) ···························67
12. ILLUSTRATED PARTS CATALOGUE
··········64
···························73
13. MACHINE ROOM ASSEMBLY SPECIFICATION
4
···················96
1. SAFETY WARNINGS
● Pull the power plug out already for the change or repair of electric
parts.
→ Be careful the electric shock.
● When exchanging the parts, use the correct parts.
→ Check the model name, rating voltage, rating current, running
temperature symbols.
● When troubleshooting, connect firmly the types of harness.
→ Make not to be separated when some power is imposed.
● Check the traces of water infiltration at the electric parts.
→ If there is a trace of water infiltration, exchange or tape the parts.
● Check the assemble status of parts after troubleshooting.
→ It should be done indiscriminately as before the repair.
● Check the use circumstance of refrigerator.
→ If the refrigerator is installed at the place that is damp or wet, or
status of installation is unstable, change the installation place.
● Do earth in case of need.
→ Particularly, Be sure to earth when there is a risk of an electric
leakage by humidity or wetness.
● Do not use multi plugs in a plug socket at the same time.
Check the power cord and socket is damaged, pressed, squeezed, or
fired.
→ If the plug or plug socket is damaged, repair or exchange that
immediately.
● Do not store the foods unstable or bottles in the freezing room.
● Do not repair the refrigerator by user himself.
● Do not store another materials except the foods.
→ Drugs or scientific materials : difficult to keep a precise temperature.
→ The inflammables(alcohol, benzene, ether, LP gas, butane gas etc.):
have a risk of explosion.
5
1. SAFETY WARNINGS
Read all instructions before repairing the product and keep to the instructions
in order to prevent danger or property damage.
CAUTION/WARNING SYMBOLS DISPLAYED
Warning
Caution
SYMBOLS
means “Prohibition”.
Indicates that a
danger of death
or serious injury
exists.
means “Do not disassemble”.
means “No contact”.
means ”The things to
be followed”.
means “Power cord should be
unplugged from the consent”
Indicates that a risk
of personal injury
or material damage
exists.
means “Earth to prevent Electric
shock”.
Warning & Caution
Pull the power plug out to
exchange the interior lamp
of the refrigerator.
● It may cause electric shock.
Use the rated components
on the replacement.
●Check the correct model, rated
voltage, rated current, operating
temperature and so on.
On repair, make sure that the
wires such as harness are
bundled tightly.
●Bundle tightly wires in order not to be
detached by the external force and then not
to be wetted.
comRated
pone
nts
Unplug
On repair, remove completely dust
or other things of housing parts,
harness parts, and check parts.
●Cleaning may prevent the possible fire by
tracking or short.
After repair, check the
assembled state of components.
●It must be in the same assembled state
when compared with the state before
disassembly.
Earth
6
Check if there is any trace
indicating the permeation
of water.
●If there is that kind of trace, change
the related components or do the
necessary treatment
such as taping
using the
insulating tape.
1. SAFETY WARNINGS
❈ Please ler users know following warnings & cautions in detail.
Warning & Caution
Do not allow users to put bottles or
kinds of glass in the freezer.
Do not allow users to store narrow
and lengthy bottles or foods in a
small multi-purpose room.
Do not allow users to store
pharmaceutical products, scientific
materials, etc., in the refrigerator.
●Freezing of the contents may inflict a wound.
●It may hurt you when refrigerator door is
opened and closed resulting in falling stuff
down.
●The products which temperature control
should not be stored in the refrigerator.
Prohibition
Do not allow users to insert the
power plugs for many products
at the same time.
●May cause abnormal generation of
heat or fire.
Prohibition
Do not allow users to store
articles on the product.
●Opening or closing the door may cause
things to fall down, with may inflict a
wound.
Prohibition
Prohibition
Do not allow users to
disassemble, repair or alter.
Do not allow users to bend the
power cord with excessive force
or do not have the power cord
pressed by heavy article.
●It may cause fire or abnormal
operation which leads to injury.
●May cause fire.
Do not
disassemble
Do not allow users to install the
refrigerator in the wet place or
the place which water splashes.
●Deterioration of insulation of electric
parts may cause electric shock or fire.
Make sure of the earth.
●If earthing is not done, it will cause
breakdown and electric shock.
Prohibition
Earth
7
2. INSTRUCTION
●
SAMSUNG side by side refrigerator has the following characteristics.
Twin Cooling System
• The refrigerator and the freezer have two
evapora
tors. Given this independent system, the freezer
and the refrigerator are cooled individually as
required and are, therefore, more efficient. Food
odor from the refrigerator does not affect food in
the freezer due to separate of air flow circulation.
Multi-Flow System
• Cool air circulates through multiple vents on
every
shelf level. This provides even distribution of
cooling inside cabinets to keep your food fresh
longer.
Beverage Station (optional)
• You do not have to open the main door to access
frequently used food in the extra
refrigerating compartment. This saves time
and money.
Deodorizer (optional)
• Reusable deodorizer keeps the refrigerator air
fresh and odor free.
CoolSelect ZoneTMDrawer (optional)
• User can select Quick Cool, Thaw and Select
buttons for quickly chill, thaw and cools items.
Select Soft Freeze, Cool or Chill to control the
temperature of drawer.
Door Alarm
• A beeper reminds you if the door is left open.
High humidity for fresher food
• You can keep food, fruit and vegetables fresh for
longer because your refrigerator supplies highly
humidified cold air. This can be up to four or five
times more effective than a normal refrigerator.
Energy-saving fridge/freezer
• Power consumption is kept to a minimum by
distributing cool air separately to the refrigerator
and freezer.
Faster cooling times
• The power freeze function allow you to freeze food
more quickly.
Abundant supply of ice and cold water
• The ice and water dispenser provides ice and cold
water at any time.
NOTE
This operation instruction covers various models.
The characteristics of your appliance may differ slightly from those described in this
manual.
8
3. INSTALLATION
1) To protect refrigerator in movement
Use padded hand truck as shown. If entrance width is
less than 30〃, remove doors prior to installation and
reattach doors according to procedure below.
2) Remove all protective tape and pad in refrigerators.
Please adjust the clearance between the doors.
3) Set the temperature control to the temperature and
wait for an hour.
The refrigerator should get slightly chilled and the motor
runs smoothly.
4) Once the refrigerator temperature is sufficiently cool
You can store food in the refrigerator. After starting the
refrigerator, it takes a few hours to reach the appropriate
temperature.
●
Disassemble the refrigerator
1)
2)
1) With the door closed, disassemble screw(①) by
using (+) screw driver and then disassemble the
upper hinge cover(②).
2) Disassemble bolts (③) and screws (④) to the
counter-clockwise by using a tool, and take off the
upper hinge (⑤) along the arrow (⑥). Take care
when you disassemble the door to ensure that it does
not fall on you.
3)
●
1)
Assemble the refrigerator
2)
1) Insert the lower hinge (①) in the bracket lower
hinge (②).
2) Assemble the door (④) in the lower hinge (③).
3)
4)
4)
3) Disassemble the door from the lower hinge (⑦) by
lifting the door (⑧).
4) Disassemble the lower hinge (⑨) from the bracket
lower hinge (⑩) by lifting the lower hinge (⑨) in the
direction of the arrow.
3) Insert the upper hinge shaft (⑤) into the hole (⑥). After
leveling between the upper hinge hole (⑦) and the
hole of the refrigerator (⑧), assemble bolts (⑨)
and screws (⑩) to the clockwise by using a tool.
4) Put the front part of the upper hinge cover (⑪) on the
front part of the upper hinge (⑫) and assemble,
starting with the front part of the upper hinge
cover. Assemble the screw to the clock wise by
using a tool.
9
4. NOMENCLATURE
R S 21 F C
SW
COLOR
NOMAL SW- SNOW WHITE(EMBO) MS- SILVER MIST (THAI)
SV- SNOW WHITE (VCM)
DB- DAISY BEIGE
RS- REAL STAINLESS
NS- NOBLE STAINLESS
TRIM KIT : SG- SILVER GLASS
LB- ILLUMANATE BLUE
MR- MIRROR
TR- TROPICAL RED
AL- ALUMINUM
NK- NATURE KHAKI
NC- NATURAL CHERRY
DW- DARK WALNUT
BG- BLACK GLASS
HANDLE TYPE
C : SKI BAR TYPE
D : CLASSIC BAR
S : CLASSIC(Handle Assembled) K : SKI BAR(Handle Assembled)
L : LONG BAR -TRIM KIT
G : LONG BAR -REAL STAINLESS
Function K : DISPENSER & HOME BAR with CoolSelect zoneTM
J : DISPENSER with CoolSelect zone
F : DISPENSER & HOME BAR
D : DISPENSER
N : BASIC MODEL
VOLUME CAPACITY: 21,23 (cu.ft)
CATEGORY
S : SBS REFRIGERATOR
BRAND : R-SAMSUNG REFRIGERATOR
Label Location
10
5. SPECIFICATIONS
5-1. Model Specification
Item
Specification
Model(RS21)
Net Capacity
Dispenser with Dispenser & H/B
Basic & H/B Dispenser Dispenser & H/B CoolSelectZone
TM
CoolSelectZoneTM
Basic
Total
557l
532l
520l
Refrigerator
346l
346l
334l
Freezer
211l
186l
186l
Net dimension(W×D×H)
908mm ✕ 719mm ✕ 1760mm
Rated Frequency and Frequency
230 ~ 240V/50Hz
155W
Motor Rated Consumption Power
Electric Heater Rated Consumption Power
401W
160W
411W
413W
423W
413W
Kind of Refrigerator
Indirect Cooling Method Refrigerator
Refrigerant
R600a
Refrigerant Input Amount
88g
(4-STAR)
Freezer Performance
Product Weight
111Kg
111Kg
Item
117Kg
117Kg
120Kg
120Kg
Specification
Model(RS23)
Net Capacity
423W
Dispenser with Dispenser & H/B
Basic & H/B Dispenser Dispenser & H/B CoolSelectZone
TM
CoolSelectZoneTM
Basic
Total
594l
565l
553l
Refrigerator
369l
369l
357l
Freezer
225l
196l
196l
Net dimension(W×D×H)
908mm ✕ 754mm ✕ 1760mm
Rated Frequency and Frequency
230 ~ 240V/50Hz
Motor Rated Consumption Power
Electric Heater Rated Consumption Power
160W
155W
401W
411W
413W
423W
413W
Kind of Refrigerator
Indirect Cooling Method Refrigerator
Refrigerant
R600a
Refrigerant Input Amount
88g
(4-STAR)
Freezer Performance
Product Weight
423W
121Kg
121Kg
11
127Kg
127Kg
130Kg
130Kg
5-2. Electric Parts Specification
Items
Specification
Models
Freezing Capacity
(4 STAR)
Compressor
Freezer
Evaporator
Defrost Sensor Defrost Cycle Refrigerator
Defrost Related Components
Room Temperature Sensor Components
Components for Freezer
Model
MK4A5Q-RIU
Starting type
R.S.C.R
Oil Charge
FREOL α- 15 (ESTER)
Freezer
SPLIT FIN TYPE
Refrigerator
SPLIT FIN TYPE
Condenser
Forced and natural convection type
Dryer
Molecular sieve XH-9
Capillary tube
0.82×3000, 5.5 Kg/cm2
Refrigerant
R600a
Model
Temperature Selection
ON(℃)
OFF(℃)
THERMISTOR
(F-SENSOR)
502AT
-25℃
-24.0
-26.0
-20℃
-19.0
-21.0
-14℃
-13.0
-15.0
Model
Temperature Selection
ON(℃)
OFF(℃)
1℃
2.0
-1.0
3℃
4.0
2.0
7℃
8.0
6.0
THERMISTOR
(R-SENSOR)
502AT
First Defrost Cycle (Concurrent defrost of F and R)
4 hr ± 10 min
Defrost Cycle(FRE)
12 ~ 24 hr (vary according to the conditions used)
Defrost Cycle(REF)
6 ~ 12 hr (vary according to the conditions used)
Pause time
10 ± 2 min
F DefrostSensor
R DefrostSensor
Thermal-Fuse
Model
THERMISTOR (502AT)
SPEC
5.0㏀ at 25℃
Model
THERMISTOR (502AT)
SPEC
Rated
5.0㏀ at 25℃
AC 250V 10A
Operating temperature
77 (+0℃/-5℃)
12
Specifications
Items
Model
Basic
Dispenser
Defrost-Heater(FRE)
Conducting at F Defrosting
215 W
Defrost-Heater(REF)
Conducting at R Defrosting
110 W
DRAIN Heater(FRE)
Conducting at F Defrosting
41 W
DRAIN Heater(REF)
Conducting at R Defrosting
35 W
DISPENSER Heater
Interlock with F-FAN
-
5W
5W
HOME-BAR Heater
Interlock with COMP
-
-
10W
-
7W
-
WATER PIPE Heater
-
Thermal-Fuse for preventing
overheating of Freezer Defrost-Heater
AC 250V 10A 77 (+0℃/-5℃)
Thermal-Fuse for preventing
overheating of Refrigerator Defrost-Heater
Electric Components
Home Bar
Condenser for
COMP
(Package type)
Running
350VAC-5μF
Starting
-
Model
J531Q35E330M385-2
Operation
33Ω±20%
Model
4TM265RFBYY-53
Temp. ON
130 ±5℃
Temp. OFF
61 ±9℃
Starting-Relay
Over-load Relay
Rated Voltage
230V/50,60Hz
MOTOR-BLDC(FRE)
DC12V/DREP302ØCA
MOTOR-BLDC(REF)
DC12V/DREP302ØCA
MOTOR-BLDC (Circuit)
DC12V/DRCP302ØLA
Lamp(FRE)
AC240V/30W
Lamp(REF)
AC240V/30W×2
Door Switch
AC250V 0.5A×2
Door Switch (HOME-BAR)
AC250V 0.5A
Power cord
AC250V 12A
Earth Screw
BSBN (BRASS SCREW)
13
6. INTERIOR VIEWS AND DIMENSIONS
6-1. The Name of Each Part(Basic)
FREEZER
REFRIGERATOR
LAMP-INCANDESCENT
COVER-GUARD
SHELF
LAMP-INCANDESCENT
GUARD
SHELF
TRAY-ICE & CASE ICE
TRAY-CHILLED ROOM
CASE-BASKET
TRAY-EGG
COVER-LEG, FRONT
GUARD
CASE-VEGETABLE
14
6-2. Part Name (HOME BAR)
FREEZER
REFRIGERATOR
LAMP-INCANDESCENT
COVER-GUARD
SHELF
LAMP-INCANDESCENT
GUARD
SHELF
TRAY-ICE & CASE ICE
TRAY-CHILLED ROOM
CASE-BASKET
TRAY-EGG
COVER-LEG, FRONT
GUARD
CASE-VEGETABLE
HOME-BAR
15
6-3. Part Name (DISPENSER)
FREEZER
REFRIGERATOR
ICE-MAKER
COVER-GUARD
ICE-CHUTE
LAMP-INCANDESCENT
LAMP-INCANDESCENT
TRAY-CHILLED ROOM
SHELF
SHELF
GUARD
TRAY-EGG
CASE-BASKET
GUARD
COVER-LEG, FRONT
CASE-VEGETABLE
16
6-4. Part Name (DISPENSER / HOME BAR / CoolSelect ZoneTM)
FREEZER
REFRIGERATOR
ICE-MAKER
COVER-GUARD
ICE-CHUTE
SHELF
LAMP
SHELF-WINE
SHELF
LAMP
GUARD
HOME BAR
CASE-BASKET
SHELF
COVER-LEG, FRONT
CoolSelect ZoneTM
TRAY EGG
CASE-VEGETABLE
GUARD
17
6-5. Dimensions of Unit
MODEL
“A”
“B”
RS21
714(719)
50
RS23
754(759)
85
18
7. FREEZING CYCLE AND COOL AIR CIRCULATION ROUTE
7-1. Freezing Cycle
Compressor → Sub-condenser → Side Cluster Pipe(FRE) → Side Cluster Pipe(REF) → Hot Pipe
→ Dryer → Capillary Tube → Refrigerator Evaporator → Freezer Evaporator→ Suction Pipe →
Compressor
Refrigerator Evaporator
SIDE CLUSTER PIPE
ACCUMULATOR
Freezer Evaporator
Dryer
SUCTION PIPE
SUB-CONDENSER
Capillary Tube
Muffler
Compressor
Hot Pipe
19
Hot Pipe
7-2. Cooling Air Circulation
Refrigerator
Freezer
20
8. MECHANICAL DISASSEMBLY
8-1. Freezer Disassembly
Control Panel
Light SWITCHES
1. Insert a flat-blade screwdriver on the slot
as shown and unlock the tabs.
2. Disconnect the wire connector in the back of
control panel
The unit have two light switches on the side
wall of freezer & refrigerator.
1.Use a small flat-blade screw driver to unlock
the hook and pull the switch out until the wire
connector is exposed.
Lights (Dispenser MODEL)
The light of freezer is located at lower side
of Auger motor case.
1.Remove ice bucket.
2.Remove the lamp cover by releasing the screw.
3.Change the bulb(rated component)
Door Gasket
The door gasket is set into groove on door liner
1.Open the door.
2.Grasp the gasket and pull it out from
the door liner.
1
3
21
2
Lights (Basic MODEL)
Drawers in FREEZER
Refer to Refrigerator Disassembly
Disassemble/assemble method is
same as the light in refrigerator
The drawers are located at bottom side of
freezer.
1.Pull the drawer out as far as it goes.
2.Lift it up slightly and pull it out from the unit.
Door Guard in FREEZER
Lift the guard up and pull it out from door liner
Ice Bucket
The ice Bucket is located in the upper portion of
the freezer. this assembly stores ice made by the
ice maker and dispenses ice cubes.
1.Lift the ice bucket up
2.Slide it out from the unit.
Shelves
1.Pull the shelf out as far as it goes.
2.Lift it up and pull it out from the unit.
22
Ice Maker
Cover Multi Freezer Assembly
1.Pull the shelf out as far as it goes.
2.Lift it up and pull it out from the unit.
1. Remove ice bucket and the Ice maker.
2. Remove the covers(①) and sensor covers(②)
3. Remove the screws(3pcs) that secured the
assembly.
4. Disconnect the wire connector(③) and the
connecter for Sensor (it can be possible
to disconnect this connector after removing
the sensor cover)
①
③
②
Cover Evaporator Assembly
1. Remove the assembly of cover multi freezer
2. Pull the assembly out toward front by holding
upper side of the assembly up to see the
connector.
3. Disconnect
the wire
connector
and take the
assembly out.
Auger Motor & case
1.Remove ice bucket.
2.Remove the screws(4) that secured the case
3.Slide it out from the unit. then, you can
disassemble the auger motor from the
back of the case.
1
2
23
Evaporator Fan motor
Ambient Thermistor
Evaporator Fan Motor is located in the back side
of the cover evaporator assembly.
1. Remove the screws(4pcs) that secured the
Fan motor assembly on the 4 corner.
2. Remove the motor case by removing another
screw and take out the motor.
The thermistor is located at inside the upper
hinge cover it sends temperature signal to the
micro-processor.
Ambient
Thermistor
Evaporator
Ice Maker Thermistor
Evaporator is located in the bottom of freezer
to produce cold air driven across evaporator
coils.
1. Remove ice bucket and the Ice maker.
2. Remove the cover multi freezer assembly.
3. Remove the cover evaporator assembly.
4. Disconnect the wire connectors.
5. Desolder the inlet and outlet tubes.
6. Take the steps in opposite to seal the
system as mentioned above.
Ice Maker Thermistor is located bottom of ice
tray. it sends temperature signal to the
micro processor.
Thermistor(Ice-Maker)
24
8-2. Refrigerator Disassembly
Beverage Station
Drawers in Refrigerator
The beverage station allows access to the
refrigerator with out opening the refrigerator
door.
1. Open the door beverage station.
2. With a small flat-blade screwdriver, take out
the rubber cap, then put it into the small hole
and push the button inside.
3. Take off the door.
The drawers are located at bottom side of
refrigerator.
1. Pull the drawer out as far as it goes.
2. Lift it up slightly and pull it out from the unit.
Lights
Door Gasket
The door gasket is set into groove on door liner
1. Open the door.
2. Grasp the gasket and pull it out from
the door liner.
The light of refrigerator are located
inside of cover multi ref. assembly.
1.Remove the lamp cover by releasing the screw.
2.Change the bulb(rated component)
1
25
2
Door Guard in REFRIGERATOR
CoolSelect zoneTM(Optional)
Lift the guard up and pull it out from door liner
1. Remove all shelves.
2. Remove two screws that secured.
Shelves
1. Pull the shelf out as far as it goes.
2. Lift it up and pull it out from the unit.
3. Disconnect the wire connector.
4. Remove the screw for disassembling the
PBA board for controlling CoolSelect zoneTM
Water filter
The water filter is
located in the upper
left hand corner of the
refrigerator. this filter
filters water for ice
maker & water
dispenser.
1. Turn the water
filter 1/2 turn
counterclockwise
and pull it down.
2. To install the filter
align the indication
mark(unlock
position) and push it up while turning
1/2 turn clockwise up to the lock position is
aligned. Do not over tighten.
26
5.Disassemble the PBA board.
2. Remove the screw and disconnect the
wire connector, then pull it out.
Cover Multi REF.
1. Remove the screw and cover lamp.
then, remove the sensor cover.
1
2
27
8-3. Machine compartment
Condenser Fan
Machine Compartment & Electric Box
The condenser fan is located in the middle of
machine compartment it cools down the subcondenser and compressor.
1) Disconnect the wire connector of Fan.
2) Remove the screws (1 EA) on the drain water
tray.
3)Take out the condenser fan assembly.
1) Disconnect the compressor cover by releasing
the screws(6EA).
2) Remove the screws which are securing the
electric box. and press the tap in electric box
coverto take outbyusing a flat-blade screw
driver.
Sub-condenser
The sub-condenser is located in the machine
compartment.
1) Desolder the compressor discharge & the
outlet of sub-condensor.
2) Take out the sub condenser.
(+)driver
(-)driver
Desoldering Point
PCB-MAIN ASSY
28
9. Operation Function
9-1) Digital Panel
······································
30
9-2) Temperature Control Function ···························· 30
9-3) Power Freeze and Power Cool Functions
·····················
31
9-4) Child Lock Function ·································· 31
9-5) Ice & Water Dispenser Function
··························
9-6) C-Fan Motor Delay Function of the Machine Compartment
9-7) CoolSelect ZoneTM Function
32
···········32
·····························
32
9-8) Water Filter Indicator Function ···························· 33
9-9) Ice-Maker Function
··································
33
9-10) Defrost Function ··································· 35
9-11) Forced Operation Function (Pull-down/R-Defrost/R,F-Defrost/Cancellation) · 36
9-12) Sound Function
···································
9-13) Exhibition Function
·································
37
37
9-14) Self-Diagnostics Function ······························ 37
9-15) Load Operation Check Function ·························· 37
9-16) Restoration Function for Power Outage ······················ 37
9-17) Set Point Shift Function ······························· 39
9-18) Table of Set Point Shift Function ·························· 40
29
9. Operation Function
9-1) Digital Panel
for Dispense Model
for Cool Select
ZoneTM
9-2) Temperature Control Function
When the system power is initally engaged, the default set temperature are -20℃ for the freezer and 3℃ for the set
refrigerator, respectively. The numbers shown on the digital display panel stand for the actual compartments
temperatures. When the compartment temperatures go down, so do the numbers on the display panel, and finally they
reach the set temperatures. Once the system is stabilized, the display temperatures are the set temperature.
1) Freezer Temperature Control.
To select a set temperature, press the Freezer Temp. button. The display shows the set temperature from -14℃ to
-25℃ in sequence.
2) Refrigerator Temperature Control.
To select a set temperature, press the Fridge Temp. button. The display shown the set temperature from 1℃ to
7℃ in sequence.
note) Because of the temperature sensor sensivity, the refrigerator can be under and/or over cooled when
the air flow is blocked by stored foods. (Temperature range of the sensor : -9℃∼30℃)
In the event of a power failure, if the freezer temperature is maintained lower than 5℃, the last
selected set temperature and functions memorized in EEPROM will be restored when the power is on.
30
Operation Function
9-3) Power Freeze and Power Cool Functions
Select the Power Freeze or Power Cool buttons separately.
These buttons are toggled ON and OFF and the indicators as well.
Although you select Power Freeze or Power Cool, the set temperatures in the freezer and refrigerator are not
changed.
● The set temperatures for the compartments can be changed while these functions are in use.
●
●
●
1) Power Freeze function
1-1) When you press the Power Freeze button, the LED indicator lights right away, but there is 10 seconds lag time
to an actual operation. When this button is pressed again, the Power Freeze function stops and the indicator is off
immediately .
1-2) If you select Power Freeze, both the compressor and the freezer fan run for 10 hours continuously.
note) When the Power Freeze is selected, it enables maximum ice maker output. The ice making interval is
reduced from 90 mins to 55 mins (55 mins after the water delivery, if the ice temperature is maintained
lower than -7℃, the ice tray will be twisted). When the ice bucket is full before 10 hours of operation,
Power Freeze is automatically terminated.
1-3) During Power Freeze, the freezer retains the current settings.
1-4) When Power Freeze expires, the indicator goes off and the freezer set temperature will be restored.
2) Power Cool function
2-1) Power Cool operation and the indicator work exactly same as the Power Freeze function.
2-2) When Power Cool is selected, COMP and R-FAN operate continuosly until the refrigerator reaches -4℃. This
function will be terminated after 2 ½ hr running.
3) When you select Power Freeze and Power Cool together
Each function works at the same time. The COMP and F-FAN run continuously and the R-FAN runs until -4℃
in the refrigerator.
4) Initial Power-On
4-1) The freezer and the refrigerator temperatures are higher than -10℃and 10℃ espectively if, respectively. If Power
Freeze is selected, the R-FAN will be off. If Power Cool is selected, the F-FAN will be off.
4-2) When both functions are selected, there is no benefit of fast cooling for each compartment.
9-4) Child Lock Function
●
When the child lock button is pressed for 3 seconds, the child lock indicator is on with an audible tone. when it is
locked, all keys can not be modified except the Ice type button. This function will prevent accidental setting that may
be caused by children or pets. To unlock the setting functions, press this button for 3 seconds again. Also, this button
has another function. When this button is pressed for 3 seconds (lock indication lamp turn on), the heater for sweat
control is off at a same time. If sweat is appeared around the cover dispenser or beverage station, press this button
for 3 seconds again. then, the light will turn off and the sweat control function will be performed. and all keys will be
unlocked at a same time.
31
Operation Function
9-5) Ice & Water Dispenser Function
●
Among several ice-maker functions, the ice extraction function is performed by mechanical system. Only the relay
control for a cubed-ice dispensing and the SSR control for the ice chute door are performed electronically.
1) Select Cubed/Crushed/Ice-off function
1-1) The Ice Type button selects Cubed/Crushed/Ice-off options in sequence.
1-2) A default setting is Cubed option.
1-3) If Cubed ice is selected, the Crushed ice bypass solenoid and the geared motor will allow Cubed ice to by pass
the ice Crusher.
1-4) If Ice-off is selected, the ice maker will stop working. This option will be terminated when Cubed and Crushed
options are selected.
Note) When the Ice-off indicator is on and the remained ice is in tray, only Cubed ice will be dispensed from
the ice bucket.
1-5) The ice chute door must be open for 5 seconds after dispensing ceases. After this 5 seconds delay, SSR will be
controlled to shut the ice chute door.
Note) Do not force to close the ice chute door. Try to dispense some more ice again to work it automatically.
2) Water Dispenser function
2-1) To dispense water, depress the water dispenser lever located in the dispenser recess.
2-2) When the lever is depressed, the water solenoid valve located in the machine compartment is open to flow water.
2-3) There is no electronic control function for this option.
9-6) C-Fan Motor Delay Function of the Machine Compartment
●
According to the ambient temperature, the condenser fan located in the machine compartment is operated with
different modes.
C-FAN
Delay function
Operation
Ranges of ambient temp.
C-FAN is ON as soon as the compressor is on.
Above 19℃
C-FAN is ON with 5 minutes delay from the compressor on.
16℃ ~ 18℃
C-FAN is OFF regardless of the compressor operation.
Below 15℃
9-7) CoolSelect ZoneTM Function (RS21K/J, RS23K/J)
To select this function, open the refrigerator door and press the button on the control panel of CoolSelect Zone TM
drawer.
● When the CoolSelect ZoneTM function is selected, the damper inside fan ductwork is open. So the refrigerator cooling
is performed first, then the damper is closed to control the CoolSelect ZoneTM temperature.
●
32
Operation Function
1) Select function
1-1) Using Select button, Cool, Chill(-1℃), and Soft Freeze(-5℃) options can be selected in sequence. Cool option
maintains a set temperature of the refrigerator.
2) Quick Cool function
2-1) If the Quick Cool is selected, LEDs will flash 60 and Min. The count will be decreased in every minute.
2-2) To cancel this function, press Quick Cool button again or Thaw button or Select button. Otherwise, it will be
terminated 60 minutes later automatically.
2-3) After this function ends, this drawer will come back to Cool option.
2-4) A defrost cycle will be postponed until Quick Cool option is finished.
3) Thaw function
3-1)When the thaw button is pressed, LEDs will flash 4, 6, 10, and 12 in sequence and Hr.
3-2) The count will be decreased in every hour.
3-3) A cancellation of this function is same as Quick Cool function.
3-4) After this function ends, this drawer will be maintained with -1℃.
3-5) While the compressor is on, this drawer retains a certain temperature and while the compressor is off, the defrost
heater is activated and R-FAN is on with a closed position of the damper.
9-8) Water Filter Indicator Function
1) Filter Indicator
1-1)This indicator initally lights in green. The light color will be changed to orange after 5 month operation then to red
at the 6th month. The EEPROM in the control board counts a period of time regardless of a power failure.
1-2)To reset the counter and the light color, press Ice Type button and Child lock button for 3 seconds simultaneously.
1-3)If these two buttons are pressed simultaneously for 5 seconds, this function will cease.
1-4)To restore this function, press these buttons again for 3 seconds.
9-9) Ice-Maker Function
●
The Ice-maker is referred to the device with an automatic ice production, storage in the ice bucket and dispensing
through the ice chute.
1) Ice-maker parts
ICE-WAKER, KIT
EJECT-MOTOR
SUPT-RUBBER
EJECT-SENSOR
LEVELING-SWITCH
ICE Full-SWITCH
TEST-SWITCH
TRAY-ICE
SCREW
FIXER-SENSOR
KNOB-TOUCH
GUIDE-ICE(Lever to check ice full)
33
COVER-SENSOR
Operation Function
2) Preparation of Ice-maker
2-1) Connect the water line to the water supply valve of refrigerator to supply water. (See how to connect a water
supply line in the owner’s manual.)
2-2) Push the bucket back fully so that the guide-ice of ice maker should not touch the back of bucket. (If the back of
bucket touches the guide-ice of ice maker, the ice maker will not make ice any more because of a ice full signal.)
2-3) It takes 6 hours to have a first ice, and throw away 2-3 times of these ice to make sure the supplied water clean.
Push the bucket back fully so that the
lever should not be pushed up.
1) Initial Operation function
1-1) Whenever the power is on, the control board checks the ice tray leveling with the leveling switch within 2 seconds.
1-2) If the leveling switch is not off position, the geared motor will turn to the initial position to make the ice tray leveled.
1-3) When the ice tray is leveled, it will remain this position for 2 hours (1 cycle time for ice production).
1-4) After 2 hours, the sensor located under the ice tray will measure the tray temperature. If the temperature is
maintained lower than -7 ℃ for 5 minutes, and the ice full switch is off position, the ice tray twisting process will
begin.
<Reference table>
Leveling S/W
ON(“LOW”)
ON(“LOW”)
OFF(“HIGH”)
Ice full S/W
ON(“LOW”)
OFF(“HIGH”)
ON(“LOW”)
Judgement
Not ready
Not ready
Not ready(Ice bucket with full of ice )
OFF(“HIGH”)
OFF(“HIGH”)
Ready
34
Remark
·MICOM Port
PIN #51: Leveling
PIN #51: Ice full
·Port level
OFF : 4.5V ↑
ON : 0.5V ↓
Operation Function
2) Water Supply function
2-1) When the ice tray is leveled again after ejecting ice, the water solenoid value will be controlled to supply water by
time check basis. (See the “Time to supply water” Table)
3) Ice production
3-1) After 90 minutes pass from the water supply, the control board will check the temperature.
3-2) If the sensor reads the temperature lower than -7℃ for more than 5 minutes, than the ice production process is
completed.
4) Test function
● In order to operate a test function, press the knob (Test Switch) for 1.5 second.
● This function can be used to check a proper working, to clean the ice tray, and to adjust the water level in the ice tray.
4-1) This function only works when the ice tray is leveled and the ice full signal is cleared.
4-2) When the water line is connected, each process such as a water supply, ejection, and leveling, can be investigated
by this button.
5) Ice off function
5-1) When the Ice off option is selected by Ice Type button, the ice making process will cease.
5-2) When the ice making process ceases, the final state will be the ice tray with the supplied water.
5-3) When Cubed or Crushed option is selected again, the control board will check an accummlated time period. After
making it 90 minutes and when the ice tray temperature is acceptable, ice ejection process will begin.
6) Functions when the freezer door is open
● When the freeze door is open, all ice maker related processes will cease in order to minimize noise and to prevent ice
from dispensing.
6-1) The ice tray stops moving regardless of the position.
6-2) The water supply process remains working as usual.
6-3) If the ice tray is in the middle of ice ejecting process, close the freezer for 30 seconds and check if the tray is
leveled. If it is not leveled, it must be out of order.
9-10) Defrost Function
1) A defrost is determined based on the accumulated compressor on-time.
2) When the power is engaged for the first time, the defrost cycle for the freezer and the refrigerator will begin after 4
hours of the accumulated compressor on-time.
3) A defrost interval depends on the ambient temperature, the number of door openings, and the door open time.
4) A minimum interval is 6 hours and a maximum is 8 hours for the refrigerator, and 12 hours and 16 hours for the
freezer, respectively.
5) The defrost heater on-time is determined by the defrost sensors as follow :
Refrigerator
Freezer
Heater ON
Below 10℃
-
Heater OFF
17℃
10℃
35
Operation Function
9-11) Forced Operation Function (Pull-down / R-Defrost / R.F-Defrost / Cancellation)
This function enables a pull-down mode, a defrost mode for the refrigerator only, a defrost mode for the freezer and
the refrigerator at the same time, and a cancellation of this function.
● Press Power Freeze and Fridge Temp. buttons for 8 seconds simultameously to get in the ready mode for a forced
operation.
● The display panel will return to normal after 20 seconds in the ready mode.
● At the ready mode, press any button(except Ice Type and Child Lock) once to start a pull-down operation, twice for a
defrost cycle for the refrigerator, three times for a defrost cycle for the freezer and the refrigerator, and finally four times
for cancellation of this function.
● Another way to cancel this function is to simply plug out and in the power cord.
●
1) Pull-down Operation
1-1) At the ready mode, press any button once then the buzzer will beep (ON for 1/2 second and OFF for 1/2 second)
until this mode is cancelled.
1-2) At this pull-down mode, the compressor will start immediately (No 5 minute delay) and if the system is in the
defrost cycle, it will be cancelled right away.
Note) If this pull-down mode begins right after the compressor was off, the compressor may not start to run due to an
overload condition.
1-3) At this mode, the compressor and freezer fan will operate continuously for 24 hours and the refrigerator fan will be
on and off according to the set temperature(-20 ℃)
1-4) After 24 hour operation, the system will be cycled at -25℃ for the freezer and 1℃ for the refrigerator.
1-5) In order to cancel this mode at any time, select the next mode on the ready mode or power off the system.
2) Defrost operation
2-1) At the pull-down mode, press any button again on the ready mode to begin the defrost cycle for the refrigerator.
2-2) The beep sound continues for 3 second at the beginning, then ON for 3/4 seconds and OFF for 1/4 second until
this mode cease.
2-3) After this operation, the system will come back to normal operation.
2-4) At this mode, press any button again on the ready mode to operate the defrost cycles for both compartments.
2-5) The beep sound continues for 3 seconds at that time, then ON for 1/4 second and OFF for 3/4 seconds until the
defrost operation cease.
3) Cancellation
3-1) At the R,F-Defrost mode, press any button again on the ready mode to return to a normal operation.
3-2) Simply unplug the power cord, then plug it again to return to a normal operation.
36
Operation Function
9-12) Sound Function
1) Sound function
1-1) To make sure a command input, whenever a button is pressed, a “ding-dong” sounds.
1-2) When two or more buttons are pressed simultaneously or if a wrong button is pressed, there is no sound.
2) Door Open Alarm
2-1) When the doors remain open for 2 minutes, there are 10 times beeps.
2-2) If the doors continue to remain open more than 2 minutes, the additional 10 beeps interval will change to 1 minute.
2-3) The beeps will cease immediately when the doors are closed.
9-13) Exhibition Function
●
This function is for a display purpose on the floor of show room or store.
1) Mode ON/OFF
1-1) For the exhibition mode, press Power Freeze and Freezer Temp. buttons simultaneously for 8 seconds until a
“ding-dong” sounds.
1-2) Press the same time buttons again for 8 seconds to cancel this mode put with a “ding-dong” sound.
2) Operation
2-1) Most of the system function except the compressor operation are working properly.
2-2) There is no defrost cycle in this mode.
9-14) Self-Diagnostics Function
1) Self-Diagnostics in the initial Power ON
1-1)The control board performs a self diagnostics test within 1 second and check out the temperature sensors abilities.
1-2) If a sensor failure occurs, a corresponding LED segment will blink with a beep.
1-3) When a LED segment blinks, only the cancellation function (Press Power Freeze and Power Cool buttons
simultaneously for 8 seconds) is acceptable.
1-4) After a replacement of bad sensor or a cancellation of this function, this self diagnostics will end.
2) Self-Diagnostics in the normal operation
2-1) To select this function, press Power Freeze and Power Cool buttons simultaneously for 8 seconds with an audible
tone.
2-2) In the self diagnostic mode, only corresponding LED segments will be illuminated (see the check list on the next
page)
2-3) After a 30 second illumination of error signal, the system will return to the normal operation.
37
Operation Function
Self-diagnostics check list
NO
①
②
③
④
⑤
⑥
⑦
⑧
⑨
⑩
⑪
⑫
⑬
Error
ICE-MAKER SENSOR
R-SENSOR
R-DEF-SENSOR
R-FAN ERROR
I/M function error
CoolSelect ZoneTM SENSOR
R-DEFROST ERROR
EXIT-SENSOR
F-SENSOR
F-DEF ERROR
F-FAN ERROR
C-FAN ERROR
F-DEFROST ERROR
If any LEDs blink, the corresponding sensors and
components must be checked for an error.
Error items of self-diagnostics
NO
Error items
LED Display
Details
Remarks
01 I/M-SENSOR
Indicate Error when the temperature sensed
I/M sensor connector missing; contact
failure, electric wire cut, short-circuit; I/M- by I/M-sensor is higher than 65℃ or lower than
sensor failure; and so on
-50℃.
02 R-SENSOR
REF sensor connector missing; contact
failure, electric wire cut, short- circuit; Rsensor itself failure; and so on
03
REF DEFROST
SENSOR
04 R-FAN ERROR
Indicate Error when the temperature sensed
by R-sensor is higher than 65℃ or lower than
-50℃.
REF evaporator internal defrosting sensor Indicate Error when the temperature sensed by R
connector missing; contact failure, electric defrosting sensor is higher than 65℃ or lower
wire cut, short-circuit; sensor itself failure;
than -50℃.
and so on
R-Fan motor operation failure; feedback
Indicate Error if the F and G signals generated by the
signal line contact failed, electric wire cut,
FAN-motor operation are not input.
short- circuit; and so on
05
I/M function
ERROR
Ice-ejector and level failed three times
or more
06
CoolSelect
ZoneTM sensor
CoolSelect ZoneTM sensor connector
missing; contact failed, electric wire cut,
short-circuit; CoolSelect ZoneTM sensor itself
failed; and so on.
07
R-DEFROST
ERROR
In the refrigerator room, if frost removal
mode is finished due to limited time of
80 minutes. Error is displayed.
-
08
Ambient Air
SENSOR
Air sensor connector missing; contact
failure, electric wire cut, short-circuit;
open air sensor itself failure; and so on
Indicate Error when the temperature sensed by
the open air sensor is higher than 65℃ or lower
than -50℃.
09 F-SENSOR
Defrost
10 FRE
SENSOR
Indicate Error when the temperature sensed by
CoolSelect ZoneTM sensor is higher than 65℃ or
lower than -50℃.
FRE sensor connector missing; contact Indicate Error when the temperature sensed
failed, electric wire cut, short-circuit; F- by F-sensor is higher than 65℃ or lower than
Room sensor itself failure.
-50℃.
FRE evaporator defrosting sensor
Indicate Error when the temperature sensed by
connector missing; contact failed,
F-defrosting sensor is higher than 65℃ or
electric wire cut, short-circuit; sensor
lower than -50℃.
itself failure; and so on
F-Fan motor operation failure; feedback
signal line contact failure, motor’s electric
wire missing; and so on.
Indicate Error if the F and G signals generated by
the FAN-motor operation are not input.
12 (COMP-FAN)
C-FAN ERROR
C-Fan motor operation failure; feedback
signal line contact failure, motor’s electric
wire missing; and so on.
Indicate Error if the F and G signals generated by the
FAN-motor operation are not input
F-DEFROST
ERROR
In the freezer room, if frost removal mode
is finished due to limited time of 80
minutes. Error is displayed
-
11 F-FAN ERROR
13
38
Operation Function
9-15) Load Operation Check Function
1) In the normal operation, press Power Freeze and Power Cool buttons simultaneously for 6 second, then the display
panel will blink for 2 seconds.
2) Press Fridge Temp. button ⓐ to get into this check mode with an audible tone.
3) Each illuminating LED segment stands for the component which has an ouput signal from the control board.
4) This mode will terminate automatically after 30 seconds.
Table of Load Mode Check List
NO
Contents
① R-FAN High or AC motor operation
②
③
④
⑤
⑥
⑦
⑧
⑨
⑩
⑪
⑫
⑬
⑭
⑮
-
R-FAN Low
R-DEF heater
Start mode
Overload mode
Low-temperature mode
Exhibition mode
COMP
F-FAN High
F-FAN Low
F-DEF-Heater
C-FAN High
C-FAN Low
Dispenser-Heater
Damper
Normal condition
※ For the R-FAN, only one rpm is applied for the current models, so that ① and ② show R-FAN operation only.
※ The F-FAN and C-FAN are operated to High/Low rpm automatically according to the operational condition.
※ ④⑤ and ⑥ only explain the system operation status according to the ambient condition
9-16) Restoration Function for Power Outage
1) When the freezer temperature is lower than 5℃, all functions on the display panel will be restored.
2) When the freezer temperature is higher than 5℃, all functions will be initialized.
(-20℃ for the freezer, 2℃ for the refrigerator, and Cubed for the Ice Type)
9-17) Set Point Shift Function
●
●
Press Freezer Temp. and Power Cool buttons simultaneously for 12 seconds to get into this mode.
In this mode, only the display LEDs for temperature will be ON.
39
Operation Function
1) Initially, all products set the code, “0” and press Power Cool or Fridge Temp. to increase or decrease # of Reference.
2) To increase or decrease #of Code,press the Power Freeze or Freezer Temp. so that it can be adjusted such as the
temperatures of freezer,refrigerator,Ice maker,and CoolSelect ZoneTM,and the quantity of water supply.
3) After 20 seconds from adjustment, a new setting will be stored in EEPROM and return to the normal display.
9-18) Table of Set Point Shift Function
1) Shift the freezer temperature sensor
Reference Value
Code
0
1
2
3
4
5
6
7
0
Temp. shift
Code
0
-0.5℃
-1.0℃
-1.5℃
-2.0℃
-2.5℃
-3.0℃
-3.5℃
8
9
10
11
12
13
14
15
40
Temp. shift
0.5℃
1.0℃
1.5℃
2.0℃
2.5℃
3.0℃
3.5℃
4.0℃
Operation Function
Example) If you are lowering the current temperature of the freezer by -3.0℃
2) Shift the refrigerator temperature sensor
Reference Value
Code
0
1
2
3
4
5
6
7
1
Temp. shift
Code
0
-0.5℃
-1.0℃
-1.5℃
-2.0℃
-2.5℃
-3.0℃
-3.5℃
8
9
10
11
12
13
14
15
Example) If you are raising the current temperature of the refrigerator by +1.5℃
41
Temp. shift
0.5℃
1.0℃
1.5℃
2.0℃
2.5℃
3.0℃
3.5℃
4.0℃
Operation Function
■The following options is limited to a model with the Ice Maker.
5) Shift the CoolSelect ZoneTM temperature sensor.
3) Adjust the time to supply water for the ice
maker
Reference Value
Reference Value
3
Code
0
5 sec
0
0
1
4 sec
1
-0.5℃
2
3 sec
2
-1.0℃
3
6 sec
3
-1.5℃
4
7 sec
4
0.5℃
5
8 sec
5
1.0℃
6
9 sec
6
1.5℃
7
10 sec
7
2.0℃
8
12 sec
9
13 sec
10
15 sec
11
17 sec
12
19 sec
13
21 sec
14
23 sec
15
25 sec
4) Shift the Ice maker temperature sensor
Reference Value
Code
1
2
3
4
5
6
7
CoolSelect ZoneTM
temperature sensor
Time to supply water
Code
0
20
4
Ice maker
temperature sensor
-7℃
-6℃
-8℃
-9℃
-10℃
-11℃
-12℃
-13℃
42
10. Circuit Descriptions
10-1) Source Power Circuit
································
44
···································
44
·····································
44
10-2) Oscillator Circuit
10-3) Reset Circuit
10-4) Door S/W Sensing Circuit ······························ 45
10-5) Temperature Sensing Circuit ···························· 45
10-6) Key Scan and Display Circuit ···························· 46
10-7) CoolSelect ZoneTM Panel Circuit
··························
48
10-8) Fan Motor(BLDC) Drive Circuit ··························· 49
10-9) EEPROM Circuit ··································· 50
10-10) Option Circuit ···································· 50
10-11) Load Drive Circuit·································· 50
43
Circuit Descriptions
10-1) Source Power Circuit
This circuit shows SMPS(Switch Mode Power Supply) which converts AC input voltage (230V, 50Hz) to a high DC
voltage (about 320V). The input AC source power is converted to DC through a wave rectifier (BD1) and the converted
DC power will generate a constant waveform on the switching transformer using a high speed (100KHz) switching motion
of TOP223Y. The D104 will rectify the generated voltage and transform into a steady 12V DC source power used for the
digital display panel and relays. The regulator (KA7805) finally transforms into 5V DC source power for the control board
and sensor’s circuits.
Caution) Be careful to handle this circuit due to high voltages (AC115V, DC170V)
10-2) Oscillator Circuit
Terminal
Oscillation Frequency
Xin(#30)
4MHz
Xout(#31)
4MHz
This is oscillator circuit to generate synchronous clocks used to calculate the time for the microprocessor operation.
Note) If the specification of a resonator changes, micro-processor can not work properly.
10-3) Reset Circuit
Terminal
Voltage
Vcc
DC 5V
RESET
DC 5V
The reset circuit is to initialize the values RAM & other sectors of micro-processor. When the power is engaged initially,
the reset voltage becomes “Low,” and it keeps “High” in the normal operation.
44
Circuit Descriptions
10-4) Door S/W Sensing Circuit
Terminal
CN30
SMW250-13 WHT
F-DOOR S/W
4
1
3
C708
104
10K
F
C404
104
R407
W/B
5
C709
104
2
HOME BAR S/W
10K
R
C403
104
44 P43
Vcc
ORG
9
S/BLU
10
Operation
Volt(state)
43 P42
1
2
R-DOOR S/W
4
1
3
R408
W/R
11
Freezer DOOR OPEN
(MICOM43PORT) DOOR CLOSE
0V (LOW)
DOOR OPEN
Ref.
(MICOM44PORT) DOOR CLOSE
0V (LOW)
5V (HIGH)
5V (HIGH)
1 ) F-Room door open is picked up based on the state (5V/0V) of the MICOM No.43 Port.
When the F-Room door opens, it becomes short between the Door S/W 1 &2.And,5V is supplied in the following
order. CN30 No.⑨ → F-Door S/W → CN30 No.① → R408(1 0K)→MICOM 43 PORT
When the state of MICOM 43 PORT is 0V, the door is picked up as closed. When it is 5V, the door is considered to be
open.
2) R-Room door open is picked up based on the state (5V/0V) of the MICOM No.44 Port.
When the R-Room door opens, it becomes short between the Door S/W 1 &2.And,5Vis supplied in the following order.
CN30 No.⑩ → R-Door S/W → CN30 No.⑤ → R407(1 0K)→MICOM 44 PORT
When the state of MICOM 44 PORT is 0V, the door is picked up as closed. When it is 5V, the door is considered to be
open.
3) When door open is detected, the MICOM have the relevant Fan Motor stop and the relevant Room Lamp light up.
Depending on the state of Door Open/Close, there are following operations; Lamp On/Off, Fan Motor On/Off and Door
open alarm. So, check relevant items upon A/S.
10-5) Temperature Sensing Circuit
# of terminal in MICOM
Remark
PIN #56 (F-SENSOR)
PIN #57 (F-DEF-SENSOR)
PIN #59 (R-SENSOR)
PIN #60 (R-DEF-SENSOR)
Micom
terminal
voltage may
change
according to
temp.
PIN #63 (EXT-SENSOR)
1) A thermistor with a negative temperature coefficient (NTC) is used for a temperature sensor.
2) Resistors, R 306 ∼ R310 and capacitors, C 301 ∼ C 305 are used for a noise protection purpose.
3) For the F-sensor, the input voltage into the micro processor (MICOM), VF is calculated by (Rth x Vcc)/(R303+ Rth),
where Rth is a corresponding resistance to the thermistor’s output (See Ref. 6 in Appendix).
4) The F-Def sensor is connected with a bimetal and a temperature sensor is in parallel. In a normal operation of the
system, the bimetal is on and 0V is input into the micro-processor. During a defrost cycle, the bimetal will be off from
54℉, and a divided voltage with R304 enter to the micro-processor to keep sensing the set temperature.
45
Circuit Descriptions
10-6) Key Scan and Display Circuit
Power Freeze
Freezer Temp.
Ice Type
Power Cool
Fridge Temp.
Child Lock
1) Key Scan and display operation.
The model uses a decorder IC which 4 inputs and 9 outputs.
If the IC 9 decorder (TC4028BP) receivesd signals from
MICOM pins (3∼6), an output signal per 2 miliseconds
comes out from Q3, Q41, Q8, Q6, Q9, Q7, Q0, Q2, and Q4
pin in sequence. This signal enters to a driver IC input
terminal of the CoolSelect ZoneTM PCB and IC5 (TD
62783AP), then approximate 11V peaks will generate from an
output terminal as shown on the next page.
46
Circuit Descriptions
The step signals of DC 11∼ 12V will be generated periodically. If a sink signal outputs from IC4, DC 11-12V will be
applied to the LED input terminal and sink the LED output terminal to 0V. Therefore, LED will be ON for 2 miliseconds.
2) Key Scan
The 6 step signals, Q6∼Q4 are applied to scan the 6 keys (buttons). When SW6 is pressed, the step signal from Q6
will be reduced to 5V and entered to the MICOM, then MICOM will match a corresponding function for SW6 key.
47
Circuit Descriptions
10-7) CoolSelect ZoneTM Panel Circuit
1) CoolSelect ZoneTM display panel and temperature sensor
1-1) CoolSelect ZoneTM is referred to as a storage drawer to implement features of Quick cool, Thaw, and Select (Soft
Freeze, Chill, and Cool).
1-2) CoolSelect ZoneTM has an additional display panel. Panel LED are off while the doors are closed. When a door is
open, micro-processor senses its signal and LEDs will be on.
1-3) The basic operational principle is the same as the key scan process.
1-4) The additional sensor can measure the temperature of CoolSelect ZoneTM. This sensor enables to control the
features of CoolSelect ZoneTM.
2) Damper drive circuit
48
Circuit Descriptions
2-1) CoolSelect ZoneTM Drawer is controlled by a damper to supply or block cold air. For Quick Cool, the damper will be
close. So cold air is supplied only to CoolSelect ZoneTM Drawer. For Thaw, the evaporator heater of refrigerator is
ON and the damper is controlled by the refrigerator temperature.
2-2) The stepping motor controlled by a Driver IC TA7774P(IC7) operates the damper. The stepping motor uses 4
combined signals to open and close the damper.
Note) To prevent the malfunction from a high humidity, a DC 12V, 1 watt heater is mounted and activated continuously.
10-8) Fan Motor (BLDC) Drive Circuit
1) Motor drive circuit
1-1) This refrigerator adopts a BLDC motor froeduce energy consumption, Motors of the freezer, refrigerator and the
machine compartment are composed of the BLDC. For RS2533, R-fan is operated by AC 115V Motor.
1-2) Voltages between high-speed and low-speed
Voltage of motor
Remark
Measure b (F-FAN) Measure C (R-FAN) Measure d(C-FAN)
High
11.1V
10V
10V
Low
10V
10V
8.3V
In the normal operation, MICOM No. 40, 41 and 42 applies a constant frequency; and
MICOM defects the signal to check the failure of motor.
(frequency(Hz)×12 = motor rpm)
Note) Under the conditions, the fans will be operated in 2 options, such as High and Low mode. Generally, it is
operated in the High mode during a day time and in the Low mode at night.
49
Circuit Descriptions
1-3) When the motor rpm is in 600∼700, it will stop automatically and it tries to resume after 10 seconds. If the motor is
not working properly after 5 time trials, it will rest for 10 minutes, then try to resume again. This process will be
done continuously.
Note) If there is an abnormal situation for the motor, the self-diagnostics will show the corresponding LED segment.
10-9) EEPROM Circuit
EEPROM is semiconductor memory not to be
erased. It can be used in the area of unstable
electric power.
10-10) Option Circuit
There are a variety of models that have a
different function. A different model can set up to
use option circuit as shown.
OPTION
D602
X CoolSelect Zone TM
O No CoolSelect Zone TM
10-11) Load Drive Circuit
1) The control of load in the system is accomplished by the main PCB.
2) Most of relays or SSRs can control the compressor, refrigerator/freezer defrost heater, and several option functions.
3) For the compressor, #18 pin of micro processor signals High (5V). This signal enters #5 pin of IC3 and #14 of output
terminal which have base and collector functions of IC3 turns on and connects the GND. Relay 73 will be grounded
through #14 of IC. Magnetic field will generate so that the second side of RY73 is activated and 115V is supplied to
the compressor. On the other hands, if #18 of micro processor turns Low(0V), #5 of IC3, the current of RY 73 relay,
and magnetic field will shut down in sequence. A contact point in secondary side of Relay 73 is off. Finally compressor
will stop.
50
Circuit Descriptions
4) The principles of other loads is the same as 3) item described.
Note) SSR(Solid State Relay) is a kind of Relay.
*COMP. equivalence circuit of drive section
51
11. Diagnostics
11-1) If power is not ON
Caution!
To check the main PCB, please apply
descriptions of operation and
references in the manual.
At the power of main PCB, the 115V power and a high-voltage over DC
170V occur. Please take care of yourself on repair and measurement.
Start
Is 230V AC fuse down?
Is power 230V
both terminals of CN10?
Is fuse on main PCB down?
Is DC 320V impressed to both
terminals of BD1?
YES
NO
Check the exchange of fuse and
disconnection cause.
YES
Check the assembly and connection of
electric wires.
NO
Exchange fuse
250V/ 2A?
Check the PCB pattern and replace BD1.
Top S/W 233Y
Is the voltage impressed DC 5.8V
between C and S ?
NO
Is 12V impressed to both
terminals of C102?
NO
Replace PCB assembly.
Is the load such as relay normal?
- Check the connections of main PCB.
- Check the connections between upper
hinge and CABI-door.
- Check the connections between door and
panel PCB.
NO
1) Replace D104 (D5S6M).
2) Replace PCB assembly.
Replace REG1(KA7805)
Is normal the load, such as
relay?
Is there any PCB soldering, short or broken?
NO
NO
1) Check the assembly of electric wires and troubleshoot.
2) Replace the panel PCB.
1) Replace the corresponding relay.
2) Check lead wire for contact.
Normal
52
Diagnostics
11-2) If the compressor and cooling fan motor don’t work normally
Start
NO
Did 5 min pass after COMP. OFF?
YES
YES
Does compressor work
with forced operation?
Did buzzer sound on forced operation?
(Check certainly after forced start.)
NO
Apply Ref.4
Is MICOM No.18 High?(5V)
Exchange MICOM and PCB.
NO
NO
Check after a lapse of 5 min.
Is freezer sensor normal?
YES
YES
Is the temp. sense
of main PCB Normal?
Is the voltage of IC03 pin No. 14 between 0-1V?
YES
Exchange and repair IC03.
(ULN2803)
Open and troubleshoot the
connection.
YES
NO
Apply Ref. 2
Is COMP relay normal?
Exchange or troubleshoot
COMP relay.
YES
NO
Is the contact of connector CN70 normal?
YES
Insert connector completely?
NO
Is COMP assembly normal?
Exchange and repair COMP.
assembly.
YES
Normal
53
NO
Open and repair the
connection.
NO
Troubleshoot the
sensor and Exchange
PCB.
Diagnostics
11-3) If defrost function
Start
Is F, R defrosting sensor by
self-diagnosis normal?
NO
Exchange and troubleshoot the
corresponding sensor.
YES
NO
Is F, R Room defrosting heater normal?
YES
See Ref. 3: ‘Check load’ in the manual.
Is temp. of the defrosting
sensor below 23℉?
Make decision on the basis of ref. 4 and
6 in the manual.
NO
Check temp. fuse,
breaking of heater wire, contact of
wire and so on.
Run forced operation for a
specified period.
YES
Perform forced defrosting for F and
R room at a time.
See test function in the manual.
Is power applied to the
respective defrosting heaters?
NO
YES
NO
Does the system
return to cooling operation after heating
for a specified period of time?
Recheck the corresponding sensor for
an error if it fails in return.
YES
Normal
Reference
If temp. of F, R defrosting sensor by the
working of heater are over 10℃, 17℃
Recheck the connection
terminal in Main PCB
YES
Check temp. fuse, breaking of heater wire,
contact of wire, and so on.
See ‘Load Drive Circuit section’ and
Ref. 2: How to check failure of relay.
Exchange or troubleshoot the failure relay or
exchange PCB ass’y.
54
NO
Repair the connection terminal.
Diagnostics
11-4) If there is a trouble with self-diagnosis
- Error of sensor can be seen on the front display of refrigerator. If power is impressed to refrigerator first, an failure of sensor is found. The refrigerator
will stop working and display(blink) the region of trouble-occurred sensor repetitively.
- Even if sensor has failure during the operation, the refrigerator will not stop working but can run the normal cooling operation because of being operated
in the Emergency Operation mode. Therefore you’ re requested to use how to check self-diagnosis in the manual.
1) If the ambient sensor has trouble
Start
Was the Main
– PCB connector(CN31) inserted
correctly?
NO
YES
See Ref. 4 (descriptions of
circuit operation, and how
to check temperature
sensor in the manual.)
A bad contact or connector missing?
Is the ambient temperature
sensor normal?
NO
YES
Exchange the temperature sensor.
Is the input of voltage to
MICOM pin No. 63 normal?
NO
YES
Check the iced solder and
short of main-PCB.
No trouble with PCB and temperature sensor.
Recheck the contact failure of connector.
2) If the temperature sensor of F and R room has trouble
Start
See Ref.4 (descriptions of
circuit operation, and how
to check temperature
sensor in the manual.)
Is the unit of
Fridge’s temperature
sensor normal?
NO
YES
Exchange the temperature sensor.
Was the Main – PCB
connector(CN30) inserted
correctly?
NO
YES
Is the sequence of
insertion of connector(CN30) wire identical to
the circuit diagram?
NO
YES
For sensor resistance per
temperature, make use of
the resistance values from
Ref. 4 and 5.
Is the input voltage to
MICOM pin No. 59 normal?
YES
No trouble with PCB and temperature sensor.
Recheck the connector for an error of contact.
55
NO
Troubleshoot a bad contact or missing of
connector.
Modify the wrong configuration of connector
wire -in case of being not inserted or
incorrectly inserted - to be coincided with the
circuit diagram.
Check if the iced solder of main PCB is
short.
Diagnostics
11-5) If alarm sound
1) If “Ding-Dong” sounds continuously
Start
Yes
Isn’t the door opened minutely?
No
Isn’t water penetrated
into the door S/W?
NO
Remove causes after
comprehending the conditions of
interference by door gasket, food etc.
YES
Freezer door MICOM No. 43,
Fridge door MICOM No. 44
– Regular voltage are 5V to Open :
0V to Close.
Is the input voltage of
main No. 43 and 44 changed at door-open,
door-close?
Exchange the door S/W.
NO
Troubleshoot the breaking of wire and
bad door S/W.
YES
Is the state of inserted connector
(CN30)being normal?
NO
Connector not inserted. Troubleshoot
poor contact.
YES
Separate the door S/W and
check if the measured value of
unit is changed from 0 to∞Ω
according to S/W ON/OFF.
NO
Is the door S/W self-unit normal?
YES
Exchange the door S/W.
Main PCB and door S/W are normal.
2) If “Beep” sounds continuously
Start
Didn’t you
select forced operation and forced
defrosting?
Selected
YES
Do buzzer
still sound after power-on
again?
YES
Check if there is any short parts due to
foreign matters and the test
jumper part in the main-PCB.
56
NO
Release the forced operation and
forced defrosting functions, or turn ON
again after power OFF.
Main-PCB is normal
Diagnostics
3) Without sound of buzzer operation
Start
Does it sound
‘Ding-Dong’if you press a button
on front panel?
YES
NO
Does it make a sound of ‘door-open’ alarm
when you are opening the door of freezer or fridge
more than 2 min?
Main PCB is normal; buzzer normal.
YES
NO
Is the bent or go-out of the buzzer
in the main PCB?
YES
NO
Refer the description of
Test function in the manual
for the Forced operation.
Are signals coming
out of MICOM No. 21 in a 1-sec cycle
after the Forced operation?
Buzzer is broken – replace it.
NO
Replace the main PCB.
(failure of MICOM)
YES
Is signal of Q801
Base ouputted with 1 sec. intervals
in the condition above?
NO
YES
Did lead of a
component fall on the vibration plate
of buzzer?
NO
The main PCB and buzzer are normal
57
Check the panel PCB with the
reference of ‘how to check panel
display’.
YES
Check the state of pattern connection
between MICOM No.21 and Q801.
(Check Open/Short)
Poor buzzer is broken down or
replace the buzzer.
Diagnostics
11-6) If the panel PCB is not working normally:
1) Where lighting of the panel PCB is disabled, or only some lamps are disabled.
Start
See Ref. 1: ‘View of the
connection cabinet-door
for the wire assembly’ in
the manual.
Is the connector
of upper hinge cover inserted
normally?
YES
NO
Is the main PCB
connector(CN50) inserted
normally?
NO
Reinsert the connector. Troubleshoot
a poor contact.
Reinsert the connector in the main
PCB.
YES
Is the connector of
door panel PCB connector inserted
normally?
NO
YES
Is lighting operated
normally when the exchange of panel
PCB?
YES
NO
1. Check the door wire of freezer – the disconnection of wire, short between wires.
2. Check the CABI wire of freezer – the disconnection of wire, short between wires.
3. Check the panel lighting circuit section within the main PCB for short open.
Reinsert the connector. Troubleshoot
a poor contact.
Panel PCB itself has trouble.
2) Where the Panel PCB key isn’t selected:
- The basic check way : If you is troubleshooting in the basic check method, then
YES
Is the locking lamp lit on?
NO
NO
Aren’t a key or more buttons
pressed continuously?
YES
Operated by
separation
Isn’t the PCB system
still operated by seperating of the
mechanism?
Refer to the description of
circuit operation in the
manual 10-6) Key scan
and display Circuit
selection’s, and measure
the wave pattern.(page 40)
YES
Is lighting
operated normally in the exchange
of panel-PCB?
YES
NO
Is a periodic
wave form outputted from the main
PCB IC9?
YES
Reassemble the PCB ass’y/Enforce
the cancellation of pressed keys.
Reassemble the PCB ass’y/Enforce
the cancellation of pressed keys.
Panel PCB has trouble for itself.
NO
1. Check the door wire of freezer – check the breaking of wire, short between wires.
2. Check the CABI wire of freezer – check the breaking of wire, short between wires.
3. Check for Short/Open of the Panel Lighting Circuit section in the main PCB.
58
Recheck after the release of locking
function.
1. Replace the main PCB.
2. Check the short wires of CoolSelect
ZoneTM panel.
Diagnostics
11-7) If fan doesn’t work:
Reference
The refrigerator has been applied with the BLDC fan motor. For RS2533, R room Fan is AC motor used. The BLDC
motor is driven by DC 8-12V.
Under the normal condition of COMP ON, it is operated together with F-FAN motor. With operation of the CoolSelect
ZoneTM function, the F-Fan motor may do not work. If the door is opened and closed once at a high ambient
temperature, the BLDC motor would be operated after a 1-minute or longer delay. Therefore, you’ re advised not to
take it for an error.
When the refrigerator is open, the freezer fan motor will also stop working simultaneously with the fan motor. (for the
purpose of performance improvement).
Start
YES
COMP OFF?
For C-FAN
For R-FAN
Is the voltage between GND
of the main-PCB and pin No. 4 of CN72
around DC 8-10V?
For F-Fan
Is the voltage DC10V between
GND of the main-PCB and pin No. 4
of CN72 ?
NO
Is the voltage DC 9-11V between
GND of the main-PCB section and
CN72 pin No. 6?
Is the voltage DC 0V between
CN30 No. 1 and No. 2
in the main-PCB?
YES
YES
Apply power around 5 minutes
after the power OFF. (Prevent
overload of compressor.)
Measure with the door closed.
- door open: DC 5V
- door close : 0V
For R-RAN
Does DC 8-10V alternate
with below DC 2V between GND of the main-PCB
section and CN72 pin No. 4?
YES
YES
NO
NO
Is the voltage DC 0V between
CN30 No. 5 and No. 6 in the main-PCB
section?
For C-FAN
Execute Forced
operation. (See page
34 in the manual)
NO
Fan works normally.
NO
Troubleshoot the
connections of door S/W.
In the first power application, the
freezer / fridge / compressor fans
work for 5 minutes regardless of the
condition.
For F-FAN
Does DC 10V alternate
with below DC 2V between GND of the main-PCB section and
CN72 pin No. 5?
YES
NO
Does DC 9-11V alternate
with below DC 2V between GND of the main-PCB section
and CN72 pin No. 6?
YES
Exchange or troubleshoot the
main PCB.
Reference
CN72 No. 3(F), 2(R),1(C) will be generated pulse signals when the motor rotates. These signals will be
inputted into MICOM. Unless signals are not inputted in the restart of motor, it will be ON 10 seconds after
the fan OFF. But if signals are not still entered, the above operation will restart four times more. Without
signals entered continuously, the motor will get restarted after 10 minutes. This function is effective where
the normal operation of motor would be restrained due to foreign matters such as ice.
59
Expected causes :
1. Check if the fan motor has failure itself.
2. Check if the wire connections have a trouble of contact.
3. Check the input of the fan motor rotation pulse in the operation motor
fan. (See the details of Fan Motor Drive Circuit section.)
Diagnostics
11-8) If CoolSelect ZoneTM isn’t operated normally
1) If the lamp of CoolSelect ZoneTM is not lit.
Start
Is the connector of
CoolSelect ZoneTM inserted correctly
in the refrigerator?
NO
YES
Is the connector of main
PCB (CN51) inserted correctly?
NO
YES
Is the connector of
CoolSelect ZoneTM panel PCB
inserted ?
If the Panel key isn’ t selected:
NO
YES
Is lighting operated
normally in the exchange of CoolSelect ZoneTM
panel PCB?
YES
NO
1.Check the wires of CoolSelect ZoneTM– check the disconnection of wire, short between wires.
2. Check the Lighting Circuit of CoolSelect ZoneTM panel in the main PCB for Short/Open.
3. Check the main PCB of CoolSelect ZoneTM assembly for Short; the wire assembly state between
the panel and main PCB.
Reinsert the connector; troubleshoot
a bad contact.
Reinsert the connector in the main
PCB.
Reinsert the connector; troubleshoot
a bad contact.
Panel PCB has trouble for itself.
2) If the Panel PCB key isn’t selected:
- The basic method is applied to check – if you fail in troubleshooting after above the execution, then
Aren’t a key or more pressed
continuously?
NO
Reassemble the PCB ass’y/Enforce
the cancellation of pressed keys
YES
Isn’t the PCB system
still operated by separation?
NO
YES
Is lighting operated
normally after the exchange of
panel-PCB?
YES
NO
Refer to 8-7) CoolSelect Zone ,
Panel Circuit and measure the
wave form.
TM
Is a periodical wave
form outputted from the main
PCB IC9?
YES
Panel PCB has trouble for itself.
NO
1. Check the wires of CoolSelect ZoneTM – check the disconnection of wire, short between wires.
2. Check Short/Open the Lighting Circuit section of CoolSelect ZoneTM panel in the main PCB.
3. Check the short of main PCB in CoolSelect ZoneTM . Check the wire assembly
60
Reassemble the PCB asswmbly and
Enforce the cancellation of pressed keys
1. Replace the main PCB.
2. Check the wire shorts of CoolSelect
ZoneTM panel.
Diagnostics
11-9) If the lamps of freezer / refrigerator does not light.
Caution!
1. When you are exchanging the lamp of freezer, please exchange or troubleshoot it with the power OFF to
avoid an electric shock.
2. Please keep in mind you do not get burnt by the excessive heating of an incandescent light bulb.
Start
YES
Is the inside lamp filament cut?
How to check :
Separate the door S/W and measure its
resistance with a measure. As the result,
every Open/Close of the door S/W should turn 0/
∞, respectively.
1) Where 0 alone comes out : Door S/W has Short
trouble.
2) Where ∞ alone comes out : Door S/W has
Open trouble.
Exchange or troubleshoot the
inside lamp.
NO
Does the F-door S/W
have a normal contact?
YES
NO
Exchange or troubleshoot the
door S/W
Check the connections of F and R-door S/W;
check and troubleshoot the inside lamp socket.
Reference
If the door is opened, then the contact of door S/W is opened and MICOM gets applied 5V to finally sense Open. If 5V has been sensed over two
minutes afterwards, then an Door-Open alarm will sound ‘Ding-Dong’ for 10 seconds in a one-minute cycle. For that reason, if the door S/W has failure, the
refrigerator can make a “Ding-Dong” sound per a one-minute cycle. Please note step for its service!
61
Diagnostics
11-10) If the solenoid in the ice-chute cover doesn’t work :
Preliminary check
1) Check if the solenoid is unconditionally operated for 0.3 sec, independent of the Open/Close condition of cover ice-route, after
a lapse of about 5 seconds from power ON. (Before installation, the cancellation of cover ice-route open is enabled.)
2) Check if the connector in upper hinge section is hook-up correctly.
Start
YES
Is the S/N(solenoid) for
0.3 sec operated after 5 seconds
from power ON?
The S/N control PCB assembly and
wire system have no trouble.
NO
Is MICOM No. 27 on
PCB maintaining High for 0.3 sec at the first
power ON?
NO
Press Ice lever and keep it open.
NO
YES
All the control system of cover iceroute has no trouble.
MICOM control port is normal.
Exchange the main PCB assembly.
YES
Is the cover closed of
S/N after about
7∼10 seconds?
YES
NO
NO
Does C-E(between C and E)
of TR Q701 turn ON for 0.3 sec?
After replace TR Q701 and check SSR71 then
exchange the failed components or replace the
PCB assembly.
YES
TR701 and SSR71 are normal
Check the stop lever and support
time-delay.
With the ice S/W ON
and ICE S/W on, ice-movement motor in F room?
YES
Subject to the ice
S/W ON, do CN31 No. 2 and MICOM No. 45
get impressed 0V?
NO
Check the ICE S/W, and troubleshoot
the wire connection system.
YES
- Main PCB and the sensing section of
ice-S/W are normal.
- Check the operation of SSR71 and
Q701.
62
Diagnostics
11-11) If Crushed Ice/Cubed Ice doesn’t work properly:
The close condition on operation
is subject to the freezer door.
Start
NO
Is ice ejected?
YES
Does ice in the ice tray exist ?
NO
YES
1) Check the ice-ejector S/W.
2) Check the door S/W.
3) Check the ice moving motor.
4) Check the cut of wire in the Ice
moving Motor section.
Do you see Ice Stop on the digital panel?
YES
1) Check the water hose for folding or
fastening.
2) Check the ice-water-way and
solenoid value
3) Check the wires of ice-maker.
Cancel Ice Stop, select
the Cubed/Crushed ice.
Crushed ice
What’s your selection
between crushed and cubed?
Cubed ice
YES
Is the Crushed Ice extracted
sufficiently?
Is the cube ice ejected sufficiently?
Measure both contact
terminals of RY77 after the
separation of CN70, CN71
connectors.
YES
Failure of Main PCB and exchange it.
NO
Does the voltage
of IC3 No. 18 turn 0V even in the ice
S/W OFF?
Failure of Main PCB. –Exchange it.
NO
Does IC3 No. 18 turn 0V if
pressing Ice S/W?
YES
Does MICOM No. 25 turn 5V if
pressing Ice S/W?
NO
Does MICOM No. 25 turn
5V if pressing Ice S/W?
Normal operation
NO
Normal operation
NO
YES
Cubed ice extracted
Measure both terminals of RY77
contact after the separation of CN70,
CN71 connectors.
Does the contact
shelf of RY77 relay turn 0Ω even in the
power OFF?
YES
YES
Failure of Main PCB(IC3) and
exchange it.
NO
Failure of Main PCB(IC3) –
exchange it.
Does the
contact shelf of RY77 relay turn 0Ωif
pressing ICE S/W?
NO
NO
NO
Exchange of Main PCB(RY77
relay).
Main PCB is normal.
- - - Check other sections.
1) Check the wire between the
AUGER motor and main
PCB.
Main PCB is normal.
- - - Necessary to check other sections.
1) Check the wire between terminals of the AUGER motor
and main PCB.
2) Failure of cube solenoid itself, or bad contact of the
connector.
63
YES
Failure of Main PCB – exchange.
(The contact terminal of RY77
relay short failure.)
Appendix Ⅰ (Reference for circuit diagnostics)
Ref. 1) Check sensors
Disconnect the connector from the Main PCB,
than measure the resistance of the following
sensors.
1. Check the resistance the Freezer sensor cn30 between the no. 2 and 3.
2. Check the resistance the Fridge Room sensor cn30 between the no. 6 and 7.
3. Check the resistance the F Defrosting sensor cn30 between the no. 2 and 4.
4. Check the resistance the R Defrosting sensor cn30 between the no. 6 and 8.
5. Check the resistance between the no. ① and ④ the ambient Air sensor cn31.
6. Check the resistance between the no. ③ and ④of the Ice-Maker sensor cn90.
7. Check the resistance between the no. ⑬ and ⑭ of the CoolSelect Zone TM
sensor cn51.
8. Decide the sensor by comparing above resistances to the temperature of
each sensor with the conversion table of sensor resistance and voltage from
the reference temperature of Ref. 6 on this manual.
※When the resistance is ∞Ωor 0Ω,check the connection of electric wire and
sensorconnector.
Ref. 2) Check Door S/W
Main PCB
Ass'y
F-DOOR S/W
(If Door Close : 1<->2 OPEN)
4
1
3
2
F-SENSOR
1
2
Check with power applied.
The Door S/W is a two-contact switch. One
detects Door Open/Close with DC 5V at the
PCB and the other one turns on/off the room
light.
Measuring Terminals
(1<->9)
3
F-DEF-SENSOR
4
4
3
R-DOOR S/W
(If Door Close : 1<->2 OPEN)
1
5
2
Measuring Terminals
(5<->10)
6
7
HOME BAR S/W
R-SENSOR
8
R-DEF-SENSOR
9
10
11
(R-Room Light)
1 . Check if the light comes on by opening the R-Door. If it lights up, check if the light goes off by pressing down
the Door S/W with the door open.
If there is any problem, check the R-Door S/W.
(R-Door Open Sensing Part of MAIN PCB)
1 . Place the positive(+) terminal on CN30 No.⑤ and the negative(-) on No.⑩.And,check the voltage.
2. When the voltage is DC 5V with the door open, it is normal.
3. When the voltage is DC 0V with the door closed, it is normal. If there is any problem, check the Door S/W and
the wire connections.
(F-Room Light)
1 . Check if the light comes on by opening the F-Door. If it lights up, check if the light goes off by pressing down
the Door S/W with the door open.
If there is any problem, check the F-Door S/W.
(F-Door Open Sensing Part of MAIN PCB)
1 . Place the positive(+) terminal on CN30 No.① and the negative(-) on No.⑨. And,checkthe voltage.
2. When the voltage is DC 5V with the door open, it is normal.
3. When the voltage is DC 0V with the door closed, it is normal. If there is any problem, check the Door S/W and
the wire connections.
64
Appendix Ⅰ (Reference for circuit diagnostics)
Ref. 3) Table of temperature sensor according to resistance and voltage conversion.
The input voltage to the MICOM PORT could be different by a hardware. This is a table based on the
voltage using the 10kohm-F.
MICOM PORT voltage when the sensor is open: about DC 5V(Vcc LEVEL)
MICOM PORT voltage when the sensor is shorted: about DC 0V(Ground LEVEL)
Temp.(℉) Resistance(㏀)
-43.6
-41.8
-40.0
-38.2
-36.4
-34.6
-32.8
-31
-29.2
-27.4
-25.6
-23.8
-22.0
-20.2
-18.4
16.6
-14.8
-13.0
-11.2
-9.4
-7.6
-5.8
-4.0
-2.2
-0.4
1.4
3.2
5.0
6.8
8.6
10.4
98.870
93.700
88.850
84.150
79.800
75.670
71.800
68.150
64.710
61.480
58.430
55.550
52.840
50.230
47.770
45.450
43.260
41.190
39.240
37.390
35.650
33.990
32.430
30.920
29.500
28.140
26.870
25.650
24.510
23.420
22.390
Voltage(V)
4.541
4.518
4.494
4.469
4.443
4.416
4.389
4.360
4.331
4.301
4.269
4.237
4.204
4.170
4.134
4.098
4.061
4.023
3.985
3.945
3.905
3.863
3.822
3.778
3.734
3.689
3.644
3.597
3.551
3.504
3.456
Temp.(℉) Resistance(㏀)
12.2
14.0
15.8
17.6
19.4
21.2
23.0
24.8
26.6
28.4
30.2
32.0
33.8
35.6
37.4
39.2
41.0
42.8
44.6
46.4
48.2
50.0
51.8
53.6
55.4
57.2
59.0
60.8
62.6
64.4
66.2
21.410
20.480
19.580
18.730
17.920
17.160
16.430
15.740
15.080
14.450
13.860
13.290
12.740
12.220
11.720
11.250
10.800
10.370
9.959
9.569
9.195
8.839
8.494
8.166
7.852
7.552
7.266
6.992
6.731
6.481
6.242
Voltage(V)
3.408
3.360
3.310
3.260
3.209
3.159
3.108
3.057
3.006
2.955
2.904
2.853
2.801
2.750
2.698
2.647
2.596
2.545
2.495
2.445
2.395
2.346
2.296
2.248
2.199
2.151
2.104
2.057
2.012
1.966
1.922
Temp.(℉) Resistance(㏀)
68.0
69.8
71.6
73.4
75.2
77.0
78.8
80.6
82.4
84.2
86.0
87.8
89.6
91.4
93.2
95.0
96.8
98.6
100.4
102.2
104.0
105.8
107.6
109.4
111.2
113.0
114.8
116.6
118.4
120.2
6.013
5.792
5.581
5.379
5.185
5.000
4.821
4.650
4.487
4.329
4.179
4.033
3.894
3.760
3.631
3.508
3.390
3.276
3.167
3.062
2.962
2.864
2.770
2.680
2.593
2.510
2.429
2.352
2.278
2.206
Voltage(V)
1.878
1.834
1.791
1.749
1.707
1.667
1.626
1.587
1.549
1.511
1.474
1.437
1.401
1.366
1.332
1.298
1.266
1.234
1.203
1.172
1.143
1.113
1.085
1.057
1.030
1.003
0.977
0.952
0.928
0.904
Appendix Ⅰ (Reference for circuit diagnostics)
Ref. 4) Service part lists of each circuit board.
NO
CODE-NO
PART NAME
SPECIFCATION
1
2
3
DA41-00195A
DA41-00195B
DA41-00185A
MAIN PCB ASS’Y
MAIN PCB ASS’Y
MAIN PCB ASS’Y
①Basic ②Basic with H/B
①Basic with CoolSelectZoneTM
①Dispenser ②Dispenser with H/B
1
1
1
4
DA41-00185B
MAIN PCB ASS’Y
①Dispenser with CoolSelectZoneTM
②Dispenser with H/B & CoolSelectZoneTM
1
5
6
7
DA41-00103T
DA41-00103U
DA41-00173A
MAIN PCB ASS’Y
MAIN PCB ASS’Y
MAIN PCB ASS’Y
①Basic ②Basic with H/B
①Basic with CoolSelectZoneTM
①Dispenser ②Dispenser with H/B
1
1
1
8
DA41-00173B
PANEL PCB ASS’Y
①Dispenser with CoolSelectZoneTM
②Dispenser with H/B & CoolSelectZoneTM
1
①Basic with CoolSelectZoneTM
②Dispenser with CoolSelectZoneTM
③Dispenser with H/B & CoolSelectZoneTM
1
9
DA41-00108A
CoolSelectZoneTM PCB ASS’Y
10
11
12
DA32-00006B
DA32-00006A
DA32-10109V
13
DA32-00105U
14
15
DA32-10109W
DA32-10109X
16
3301-000016
17
DA27-00002A
R-DEFROST Sensor
F-DEFROST Sensor
Ambient Temp.Sensor
R-Temp.Sensor
F-Temp.Sensor
F-Temp.Sensor
CoolSelectZoneTM PCB ASS’Y
FERRIETE CORE
(LOCK TYPE)
NOISE FILTER
Q’TY
PX-41C
PX-41C
PX-41C
PX-41C
PX-41C (Use Only Basic Models)
1
1
1
PX-41C (Use Only Dispenser Models)
PX-41C
1
-
0
1
1
USE ALL MODEL
※ The last no. of the code number such as DA41-xxxxx? for the Main PCB-ASS’Y could be changed by
MICOM and option.
66
67
CIRCUIT DIAGRAM
For Basic Models
PANEL PCB
BLK
BRN
RED
ORG
YEL
PNK
BLU
PRP
GRY
WHT
S/BLU
W/BLK
W/RED
W/BLU
MAIN PCB
N
BLK
BLK
BRN
RED
RED
CN10(WHT)
DEFROST HEATER,F
ORG
13
RED
YEL
BLKTHERMO FUSE,F
PNK
RED
14-PIN
F-DRAIN HEATER
BLU
DEFROST HEATER,R
PRP
RED
BLK THERMO FUSE,R
GRY
YEL
WHT
DRAIN HEATER
S/BLU
GRN/YEL
S/BLU
W/BLK
M
C
W/RED
W/BLU
PNK
S COMPRESSOR OVERLOAD
CN50(WHT)
PROTECTOR
RUNNING CAPACITOR PTC RELAY
BLK
14
13
12
12
13
14
CN70(WHT)
W/BLK
F-ROOM LAMP
W/BLK
R-ROOM LAMP
W/BLK
CN71(WHT)
7
6
5
4
3
2
1
GND
Vcc
Vcc
Vcc
FG
FG
FG
F-FAN MOTOR
(BLDC)
R-FAN MOTOR
(BLDC)
COOLING-FAN
MOTOR (BLDC)
CN72(WHT)
F-ROOM DOOR S/W
4
3
1
2
R-ROOM DOOR-S/W
4
1
2
3
F-ROOM SENSOR
DEFROST SENSOR,F
R-ROOM SENSOR
DEFROST SENSOR,R
1
2
3
4
5
6
7
8
WHT 1
AMBIENT SENSOR
2
3
WHT 4
CN31(WHT)
CN30(WHT)
Reference
RED-RED
BLU-BLUE
ORG-ORANGE
P/BLU-PINK/BLUE
BRN-BROWN
PNK-PINK
GRY-GRAY
W/BLU-WHITE/BLUE
WHT-WHITE
YEL-YELLOW
BLK-BLACK
PRP-PURPLE
W/BLK-WHITE/BLACK
S/BLU-SKY/BLUE
E-EARTH
W/RED-WHITE/RED
68
RED
L
GRN/YEL
BLK
NOISE
FILTER
RED
RED
BLK
RED
BLK
RED
RED
CIRCUIT DIAGRAM
For Dispenser Models
PANEL PCB
BLK
BRN
RED
ORG
YEL
PNK
BLU
PRP
GRY
WHT
S/BLU
W/BLK
W/RED
W/BLU
MAIN PCB
N
12
13
14
W/BLK
4
CN71(WHT)
10
9
7
6
4
3
2
1
EJECT MOTOR
ICE SENSOR
TEST S/W
HORIZONTAL S/W
ICE CHECK S/W
F-ROOM DOOR S/W
1
2
R-ROOM DOOR-S/W
4
1
2
3
F-ROOM SENSOR
DEFROST SENSOR,F
R-ROOM SENSOR
DEFROST SENSOR,R
RED
BLK
WHT
WHT
GRY
BLU
PRP
S/BLU
CN90(RED)
1
2
3
4
5
6
7
8
7
6
5
4
3
2
1
ICE CUBE SOLENOID
GND
Vcc
Vcc
Vcc
FG
FG
FG
GRN/YEL
R-FAN MOTOR
(BLDC)
COOLING-FAN
MOTOR (BLDC)
CN72(WHT)
WHT 1
ORG 2
ORG 3
WHT 4
CN31(WHT)
AMBIENT SENSOR
5
6
ICE S/W
12
13
CN30(WHT)
Reference
RED-RED
BLU-BLUE
ORG-ORANGE
P/BLU-PINK/BLUE
BRN-BROWN
PNK-PINK
GRY-GRAY
W/BLU-WHITE/BLUE
WHT-WHITE
YEL-YELLOW
BLK-BLACK
PRP-PURPLE
W/BLK-WHITE/BLACK
S/BLU-SKY/BLUE
E-EARTH
W/RED-WHITE/RED
69
RED
AUGER MOTOR
WATER-SOLENOID VALVE
F-FAN MOTOR
(BLDC)
1
2
3
4
5
6
7
8
RED
RED
ICE ROUTE SOLENOID
ICE MAKER-SOLENOID VALVE
FILTER
4
3
L
BLK
BLK
RED
BLK
BRN
RED
GRN/YEL
RED
NOISE
CN10(WHT)
DEFROST HEATER,F
FILTER
ORG
13
RED
YEL
BLKTHERMO FUSE,F
BLK
PNK
14-PIN
RED
F-DRAIN HEATER RED
BLU
RED
DEFROST HEATER,R
PRP
RED DRAIN HEATER
THERMO FUSE,R
GRY
RED BLK
BLK
YEL
WHT
ICE
MAKER
PIPE
HEATER
S/BLU
GRN/YEL
S/BLU
W/BLK
M
C
W/RED
RED
W/BLU
PNK
S COMPRESSOR OVERLOAD
CN50(WHT)
PROTECTOR
RUNNING CAPACITOR PTC RELAY
BLK
BLK
DISPENSER HEATER
1
RED
CN70(WHT)
W/BLK
F-ROOM LAMP
RED
R-ROOM LAMP
W/BLK
RED
14
13
12
BLK
2
RED BLK FILTER
3
WATER S/W
GRY
BLK
CIRCUIT DIAGRAM
For Dispenser & CoolSelect ZoneTM Models
PANEL PCB
BLK
BRN
RED
ORG
YEL
PNK
BLU
PRP
GRY
WHT
S/BLU
W/BLK
W/RED
W/BLU
COOLSELECT
ZONE PCB
COOLSELECT ZONE
SENSER
WHT
WHT
BLK
BRN
RED
ORG
YEL
PNK
BLU
PRP
GRY
WHT
S/BLU
W/BLK
W/RED
W/BLU
EJECT MOTOR
ICE SENSOR
TEST S/W
HORIZONTAL S/W
ICE CHECK S/W
F-ROOM DOOR S/W
4
3
1
2
R-ROOM DOOR-S/W
4
1
2
3
MAIN PCB
N
12
13
14
12
13
14
L
BLK
BLK
RED
BRN
RED
GRN/YEL
RED
NOISE
CN10(WHT)
DEFROST HEATER,F
FILTER
ORG
13
RED
YEL
BLKTHERMO FUSE,F
PNK
14-PIN
RED
F-DRAIN HEATER RED
BLU
RED
DEFROST HEATER,R
PRP
RED DRAIN HEATER
THERMO FUSE,R
GRY
RED BLK
BLK
YEL
WHT
ICE MAKER PIPE HEATER
S/BLU
GRN/YEL
S/BLU
W/BLK
M
C
W/RED
RED
W/BLU
PNK
S COMPRESSOR OVERLOAD
CN50(WHT)
PROTECTOR
RUNNING CAPACITOR PTC RELAY
BLK
BLK
DISPENSER HEATER
BRN
1
RED
RED
CN70(WHT)
ORG
W/BLK
F-ROOM LAMP
YEL
RED
(16-PIN)
USE
R-ROOM LAMP
W/BLK
PNK
RED
14-PIN
BLU
PRP
W/BLK
4
RED
GRY
ICE ROUTE SOLENOID
WHT
RED
ICE
MAKER-SOLENOID
VALVE
FILTER
S/BLU
RED
12 W/BLK
AUGER MOTOR
GRN/YEL
13 W/RED
ICE CUBE SOLENOID
14 W/BLU CN71(WHT)
15 16
CN51(RED)
GND
7
WATER-SOLENOID VALVE
10
1 RED
Vcc
F-FAN MOTOR
6
BLK
9
2 BLK
2
(BLDC)
R-FAN MOTOR
Vcc
5
(BLDC)
3 WHT
7
RED BLK FILTER GRY
Vcc
3
4
6
4 WHT
FG
WATER S/W
COOLING-FAN
3
5 GRY
4
FG
MOTOR
(BLDC)
2
3
6 BLU
FG
1
2
7 PRP
8 S/BLU CN72(WHT)
1
DAMPER HEATER
CN90(RED)
3
BLK 1
COOLSELECT ZONE
DAMPER ASS'Y
4
BLK 2
A
1
1
WHT 3
14
13
12
F-ROOM SENSOR
DEFROST SENSOR,F
R-ROOM SENSOR
DEFROST SENSOR,R
2
3
4
5
6
7
8
BLU 4
YEL 5
RED 6
CN73(WHT)
WHT 1
ORG 2
ORG 3
WHT 4
CN31(WHT)
6
2
5
A B
AMBIENT SENSOR
5
6
ICE S/W
12
13
CN30(WHT)
Reference
RED-RED
BLU-BLUE
ORG-ORANGE
P/BLU-PINK/BLUE
BRN-BROWN
PNK-PINK
GRY-GRAY
W/BLU-WHITE/BLUE
WHT-WHITE
YEL-YELLOW
BLK-BLACK
PRP-PURPLE
W/BLK-WHITE/BLACK
S/BLU-SKY/BLUE
E-EARTH
W/RED-WHITE/RED
70
B
BLK
BLK
BLK
BLK
CIRCUIT DIAGRAM
For Dispenser & Home Bar Models
PANEL PCB
BLK
BRN
RED
ORG
YEL
PNK
BLU
PRP
GRY
WHT
S/BLU
W/BLK
W/RED
W/BLU
MAIN PCB
N
BLK
BLK
BRN
RED
RED
CN10(WHT)
DEFROST HEATER,F
ORG
13
RED
YEL
BLKTHERMO FUSE,F
PNK
14-PIN
F-DRAIN HEATER RED
BLU
DEFROST HEATER,R
PRP
RED DRAIN HEATER
THERMO FUSE,R
GRY
RED BLK
BLK
YEL
WHT
ICE
MAKER
PIPE
HEATER
S/BLU
GRN/YEL
S/BLU
W/BLK
M
C
W/RED
W/BLU
PNK
S COMPRESSOR OVERLOAD
CN50(WHT)
PROTECTOR
RUNNING CAPACITOR PTC RELAY
BLK
14
13
12
12
13
14
CN70(WHT)
CN71(WHT)
10
9
7
6
4
3
2
1
EJECT MOTOR
ICE SENSOR
TEST S/W
HORIZONTAL S/W
ICE CHECK S/W
F-ROOM DOOR S/W
4
3
1
2
F-ROOM SENSOR
R-ROOM DOOR-S/W DEFROST SENSOR,F
4
1
WHT
2
3
R-ROOM SENSOR
HOME-BAR
S/W
DEFROST SENSOR,R
RED
BLK
WHT
WHT
GRY
BLU
PRP
S/BLU
CN90(RED)
1
2
3
4
5
6
7
8
7
6
5
4
3
2
1
GND
Vcc
Vcc
Vcc
FG
FG
FG
12
13
COOLING-FAN
MOTOR (BLDC)
AMBIENT SENSOR
ICE S/W
Reference
WHT-WHITE
YEL-YELLOW
BLK-BLACK
PRP-PURPLE
W/BLK-WHITE/BLACK
S/BLU-SKY/BLUE
E-EARTH
W/RED-WHITE/RED
71
RED
RED
AUGER MOTOR
WATER-SOLENOID VALVE
R-FAN MOTOR
(BLDC)
CN30(WHT)
RED-RED
BLU-BLUE
ORG-ORANGE
P/BLU-PINK/BLUE
BRN-BROWN
PNK-PINK
GRY-GRAY
W/BLU-WHITE/BLUE
RED
RED
RED
ICE ROUTE SOLENOID
ICE MAKER-SOLENOID VALVE
F-FAN MOTOR
(BLDC)
5
6
BLK
W/BLK
CN72(WHT)
WHT 1
ORG 2
ORG 3
WHT 4
CN31(WHT)
BLK
RED
R-ROOM LAMP
1
2
3
4
5
6
7
8
BLK
RED
F-ROOM LAMP
GRN/YEL
GRN/YEL
RED
RED
W/BLK
ICE CUBE SOLENOID
L
NOISE
FILTER
HOME-BAR HEATER
1
DISPENSER HEATER
W/BLK
4
FILTER
RED
BLK
2
RED BLK FILTER
3
WATER S/W
GRY
BLK
CIRCUIT DIAGRAM
For Dispenser & Home Bar & CoolSelect ZoneTM Models
PANEL PCB
BLK
BRN
RED
ORG
YEL
PNK
BLU
PRP
GRY
WHT
S/BLU
W/BLK
W/RED
W/BLU
COOLSELECT
ZONE PCB
COOLSELECT ZONE
SENSER
WHT
WHT
12
13
14
BLK
BRN
RED
ORG
YEL
PNK
BLU
PRP
GRY
WHT
S/BLU
W/BLK
W/RED
W/BLU
12
13
14
EJECT MOTOR
ICE SENSOR
TEST S/W
HORIZONTAL S/W
ICE CHECK S/W
F-ROOM DOOR S/W
4
3
1
2
MAIN PCB
N
L
BLK
BLK
RED
BRN
RED
GRN/YEL
RED
NOISE
CN10(WHT)
DEFROST
HEATER,F
FILTER
ORG
13
THERMO
FUSE,F
RED
YEL
BLK
PNK
14-PIN
RED
F-DRAIN HEATER RED
BLU
RED
DEFROST HEATER,R
PRP
RED DRAIN HEATER
THERMO FUSE,R
GRY
RED BLK
BLK
YEL
WHT
ICE
MAKER
PIPE
HEATER
S/BLU
GRN/YEL
S/BLU
W/BLK
M
C
W/RED
RED
W/BLU
PNK
S COMPRESSOR OVERLOAD
CN50(WHT)
PROTECTOR
RUNNING CAPACITOR PTC RELAY
BLK
BLK
BRN
RED
HOME-BAR HEATER
RED
1
CN70(WHT)
ORG
DISPENSER HEATER
W/BLK
F-ROOM LAMP
YEL
RED
(16-PIN)
USE
R-ROOM LAMP
W/BLK
PNK
RED
14-PIN
BLU
PRP
W/BLK
4
RED
GRY
ICE ROUTE SOLENOID
WHT
RED
FILTER ICE MAKER-SOLENOID VALVE
S/BLU
RED
12 W/BLK
AUGER MOTOR
GRN/YEL
13 W/RED
ICE CUBE SOLENOID
14 W/BLU CN71(WHT)
15 16
CN51(RED)
GND
7
WATER-SOLENOID VALVE
10
1 RED
Vcc
F-FAN MOTOR
6
BLK
9
2 BLK
2
(BLDC)
R-FAN MOTOR
Vcc
5
(BLDC)
3 WHT
7
RED BLK FILTER GRY
Vcc
3
4
6
4 WHT
FG
WATER S/W
COOLING-FAN
3
5 GRY
4
FG
MOTOR (BLDC)
2
3
6 BLU
FG
1
2
7 PRP
8 S/BLU CN72(WHT)
1
DAMPER HEATER
CN90(RED)
3
BLK 1
COOLSELECT ZONE
DAMPER ASS'Y
4
BLK 2
A
1
1
WHT 3
14
13
12
F-ROOM SENSOR
R-ROOM DOOR-S/W DEFROST SENSOR,F
4
1
WHT
2
3
HOME-BAR R-ROOM SENSOR
S/W
DEFROST SENSOR,R
2
3
4
5
6
7
8
12
13
BLU 4
YEL 5
RED 6
CN73(WHT)
WHT 1
ORG 2
ORG 3
WHT 4
CN31(WHT)
6
2
5
A B
AMBIENT SENSOR
5
6
ICE S/W
CN30(WHT)
Reference
RED-RED
BLU-BLUE
ORG-ORANGE
P/BLU-PINK/BLUE
BRN-BROWN
PNK-PINK
GRY-GRAY
W/BLU-WHITE/BLUE
WHT-WHITE
YEL-YELLOW
BLK-BLACK
PRP-PURPLE
W/BLK-WHITE/BLACK
S/BLU-SKY/BLUE
E-EARTH
W/RED-WHITE/RED
72
B
BLK
BLK
BLK
BLK
12 . Illustrated Parts Catalog.
12-1) Freezer Room Exploded View
1
1
1-2
1-3
1-2
1-3
1-1
1-1
12
13
13-2
13-3
13-4
13-1
2-2
13-7
16
2-3
2
13-6
2-1
13-8
17
13-5
13-6
4
4-2
4-1
3-2
3-4
6
6
14
15
3-1
3
5
3-3
18-5
18-3
5-2
18-9
18-10
5-1
18-12
6
7
8
8-1
18-8
8-2
18-12
18-11
18-4
18-6
7-1
6
18-2
7-2
18
9
9-2
7
9-1
6
10
10-1
18-1
10-2
10-3
19
19-2
19-1
11
11-1
20
11-2
19-3
11-3
73
Illustrated Parts Catalog.
■ Parts List of Freezer
NO
CODE-NO
PART NAME
1
1-1
1-2
1-3
2
2-1
2-2
2-3
3
3-1
3-2
3-3
3-4
4
4-1
4-2
5
5-1
5-2
6
7
7-1
7-2
8
8-1
8-2
9
9-1
9-2
10
10-1
10-2
10-3
11
11-1
11-2
11-3
12
13
13-1
13-2
13-3
13-4
13-5
13-6
13-7
14
15
16
DA67-00180A
DA67-00175A
DA67-00177B
DA64-00090A
DA67-00181A
DA67-00146A
DA67-00177C
DA64-00090A
DA66-00047A
DA71-00059A
DA66-00032A
DA64-00084A
DA61-20136A
DA97-01292A
DA61-00044B
DA63-00202A
DA97-01291A
DA61-00045B
DA63-00202A
6002-000215
DA67-00186A
DA67-00155A
DA63-00179A
DA97-01247A
DA61-60179A
DA63-40256B
DA97-01248A
DA61-60180A
DA63-40256B
DA67-00182C
DA67-00150A
DA63-00174C
DA63-00170A
DA67-00183C
DA67-00151A
DA63-00174C
DA63-00170A
DA34-10121A
DA97-00101J
DA63-00363A
DA72-00245A
DA72-00158F
DA72-00159E
DA62-00219A
DA70-00215B
DA32-10105H
DA63-00178A
DA63-00162B
4713-001132
SHELF-FRE ASSY
SHELF-FRE
SHELF GLASS
TRIM-SHELF
SHELF-FRE ASSY
SHELF-FRE
SHELF GLASS
TRIM-SHELF
TRAY-ICE ASSY
FIXER-TRAY ICE
TRAY-ICE
KNOB-TRAY ICE
SPRING ETC-ICE MAKER
ASSY RAIL-BASKET,L
RAIL-BASKET,L
GROMMET-RAIL
ASSY RAIL-BASKET,R
RAIL-BASKET,R
GROMMET-RAIL
SCREW-TAPPING
CASE-ICE CUBE ASSY
CASE-TRAY ICE
COVER-TRAY
ASSY RAIL LOW,L
RAIL-LOW
GROMMET-RAIL
ASSY RAIL LOW,R
RAIL-LOW
GROMMET-RAIL
CASE-BASKET UPP ASSY
CASE-BASKET
COVER-FRONT FRE,B
COVER-FRONT
CASE-BASKET LOW ASSY
CASE-BASKET
COVER-FRONT FRE,B
COVER-FRONT
SWITCH-DOOR
ASSY COVER-MULTI FRE
COVER EVAP-FRE,FRONT UPP
INSULATION DUCT-FRE,UPP
SEAL EVAP-FRONT FRE,L
SEAL EVAP-FRONT,FRE R
SEAL-AIR FRE,UPP
PLATE-INS,DUCT
SENSOR-ASSY
COVER-SENSOR
COVER SENSOR-B
LAMP-INCANDESCENT
Spec
GLASS-SHELF
HIPS
GLASS
PVC
GLASS-SHELF
HIPS
GLASS
PVC
HIPS
HIPS
HIPS
STS304 , PI10
HIPS
HIPS
NY-6
HIPS
HIPS
NY-6
TH,+,1,M4.0,L16,ZPC(YEL)
HIPS
GPPS
HIPS
HIPS
GPPS
NY-6
HIPS
HIPS
NY-6
PP
GPPS
HIPS
PP
GPPS
HIPS
PA6
UPP PP
FOAM-PS
T2.0
T2.0
OJC-3000 , T7
RD-PVC , T1.2
502AT, -10~35 , 5V
GPPS
ABS , PNC2
240V , 30W
74
Quantity
1
1
1
2
1
1
1
2
1
1
2
2
2
2
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
2
3
Remark
Illustrated Parts Catalog.
■ Parts List of Freezer
NO
CODE-NO
PART NAME
17
18
18-1
18-2
18-2
18-4
18-5
18-6
18-7
18-8
18-9
18-10
18-11
19
19-1
19-2
19-3
20
20-1
20-1
DA63-00364A
DA97-00360P
DA63-00153B
DA62-00186A
DA72-00227A
DA61-00417A
DA63-00713A
DA31-00038A
DA31-00020E
DA39-00060B
DA63-01146A
6002-000471
DA61-20128A
DA96-00090B
DA32-00006B
DA47-10148J
DA61-00603A
DA97-00339B
DA47-00092B
DA70-00404A
COVER LAMP-FRE,A
ASSY COVER EVAP-FRE
COVER EVAP-FRE(FRONT LOW)
INSULATION DUCT-FRE
SEAL-AIR FRE LOW
CASE MOTOR
COVER-MOTOR
FAN-CIRCUIT
MOTOR DC-BLDC,SENSOR
WIRE HARNESS-MOTOR
GROMMET-MOTOR
SCREW-TAPPING
SPRING ETC-FAN
ASSY EVAP-FRE
SENSOR ASSY
THERMO FUSE-ASSY
FIXER-SENSOR
ASSY-PLATE DRAIN,FRE
HEATER DRAIN-FRE
PLATE-DRAIN FRE
Spec
PP
BLDC
PP
FOAM-PS
OJC-3000 , T5
ABS SCRAP
PP
ABS
DREP3020LA
NBR
TH,+,1,M4,L12,STS304
STS27 , PI7.8 , ID1.0
230V
PX-41C RD SEN,A TOP,-10°C
SW-102T , 250V
PP
230V , 41W
230V , 41W
GALVALUME , T0.5
75
Quantity
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
Remark
12 . Illustrated Parts Catalog.
12-2) Refrigerator Room Exploded View (RS21N, RS21H, RS21D, RS21F, RS23N, RS23H, RS23D, RS23F)
14-3
23
14-4
14-2
1
14
12
14-1
12
9
1
14-5
13
10
4
4-1
11
3
18
4-2
17
14-7
12
12
18-2
18-1
15
5
18-3
5-1
16
5-2
12
19
16-3
1
16-1
16
16-2
22
22-1
27
20
22-7
22-6
2
22-2
27-6
22-3
27-5
27-8
22-4
22-5
27-4
27-7
6-1
21
6
27-2
6-3
27-3
6-2
27-11
6-4
25-2
25
25-1
7
26
8
8-1
26-2
26-1
12
27-10
12
8-3
8-2
24
8-4
76
27-12
27-9
27-11
Illustrated Parts Catalog.
■ Parts List of Refrigerator
NO
CODE-NO
PART NAME
1
2
3
4
4-1
4-2
5
5-1
5-2
6
6-1
6-2
6-3
6-4
7
8
8-1
8-2
8-3
8-4
9
10
11
12
13
14
14-1
14-2
14-3
14-4
14-5
14-6
14-7
15
16
16
16-1
17
18
18-1
18-2
18-3
19
19-1
19-2
20
21
22
23
DA67-00149A
DA67-00148B
DA66-00038A
DA97-01247A
DA61-60179A
DA63-40256B
DA97-01248A
DA61-60180A
DA63-40256B
DA67-00184C
DA63-00175A
DA63-00177C
DA67-00152A
DA64-00085A
DA63-10942B
DA67-00185C
DA63-00175A
DA63-00177C
DA67-00153A
DA64-00085A
DA63-01638A
DA63-00178A
DA63-00162B
6002-000215
4713-001132
DA97-01420A
DA63-00158A
DA72-00144A
DA62-00566A
DA62-00566B
DA62-00587A
DA47-00025H
DA32-10105H
DA67-40250E
DA67-00711A
DA67-00145A
DA71-20252A
DA34-10110B
DA96-00013H
DA32-00006B
DA47-10148J
DA61-00453A
DA47-00039B
DA47-00038B
DA70-00231A
DA97-00724A
DA29-00003A
DA97-00725C
DA63-00586A
SHELF-REF UPP
SHELF REF-LOW
TRAY-CHIL ROOM
ASSY RAIL LOW,L
RAIL-LOW
GROMMET-RAIL
ASSY RAIL LOW,R
RAIL-LOW
GROMMET-RAIL
CASE-VEG UPP ASSY
COVER-FRONT
COVER-FRONT REF,B
CASE-VEG
KNOB-MOIS CONT
COVER-VEG,LOW
CASE-VEG LOW ASSY
COVER-FRONT
COVER-FRONT REF,B
CASE-VEG
KNOB-MOIS CONT
COVER-LAMP REF
COVER-SENSOR
COVER SENSOR-B
SCREW-TAPPING
LAMP-INCANDESCENT
ASSY COVER-MULTI REF
COVER-MULTI
INSULATION
SEAL-MULTI REAR,L
SEAL-MULTI REAR,R
SEAL-MULTI AL,UPP
LAMP HOLDER
SENSOR-ASSY
TRAY-UTILITY
SHELF WIRE-WINE,RACK
SHELF-WINE
FIXER-GROMMET DOOR
SWITCH-DOOR
ASSY EVAP-REF
SENSOR ASSY
THERMO FUSE-ASSY
FIXER-SENSOR
HEATER-DRAIN ASSY,REF
HEATER-DRAIN,REF
PLATE-DRAIN,REF
ASSY-COVER FILTER
FILTER-WATER ASS'Y
ASSY CASE-FILTER
COVER-TUBE FILTER
Spec
GLASS
GLASS
GPPS
HIPS
HIPS
NY-6
HIPS
HIPS
NY-6
HIPS
HIPS
GPPS
PP
ABS
HIPS
HIPS
HIPS
GPPS
PP
ABS
PP
GPPS
ABS , PNC2
TH,+,1,M4.0,L16,ZPC(YEL)
240V , 30W
PP
FOAM-PS
T2.0
T2.0
FOAM-PE + AL50um
E 14,250V,1A,370,NTR,PBT 5VA
502AT,K-PJT,-10~35,5V,5KOHM
GPPS
MSWR10
HIPS
ABS
125/1.5A
230V , 110W
PX-41C RD SEN,A TOP,-10°C
SW-102T,250V
PP
240V
240V
SBHG1 , T0.6
ABS
A-TOP,EXP,INSERT-FILTER
PP
77
Quantity
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
2
2
15
3
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
Remark
Illustrated Parts Catalog.
■ Parts List of Refrigerator
NO
CODE-NO
PART NAME
24
25
25-1
25-2
26
26-1
26-2
27
27-1
27-2
27-3
27-4
27-5
27-6
27-7
27-8
27-9
27-10
27-11
27-12
DA74-00056F
DA63-00365C
DA63-00163A
DA02-90106K
DA63-00366C
DA63-01643A
DA02-90106K
DA63-00217L
DA63-00159B
DA72-00142A
DA72-00229A
DA72-00143A
DA67-00158A
DA63-00184A
DA31-00016A
DA31-00020E
DA39-00060H
DA63-00457A
6002-000471
DA61-20128A
TANK WATER-ASSY
ASSY-COVER PURIFIER,L
COVER-PURIFIER L
CATALYST-LTC
ASSY-COVER PURIFIER,R
COVER-PURIFIER R
CATALYST-LTC
COVER EVAP-REF ASSY
COVER EVAP-REF
INSULATION-DUCT
SEAL-AIR,REF UPP
INSULATION-DUCT
CASE-MOTOR
COVER-MOTOR
FAN-CIRCUIT
MOTOR DC-BLDC
WIRE HARNESS-MOTOR
GROMMET-MOTOR
SCREW-TAPPING
SPRING ETC-FAN
Spec
HD-PE
Quantity
1
1
ABS
SS400-10-3
1
ABS
SS400-10-3
PP
FOAM-PS
OJC-3000 , T5
FOAM-PS
PP
PP
-,ET-PJT,-,-,-,12,Ø95,Ø63.
DREP3020LA,ET,0.245
ET-PJT,-,-,-,L450,-,NBR
TH,+,1,M4,L12,PASS,STS304
STS27 , PI7.8 , ID1.0
78
1
1
1
1
1
1
1
1
1
1
2
1
1
Remark
12 . Illustrated Parts Catalog.
12-3) Refrigerator Room Exploded View (RS21J, RS21K, RS23J, RS23K)
13-3
22
13-4
13-2
1
13
11
13-1
11
2
8
27
3
13-5
28
12
9
10
17
4
4-1
16
13-7
11
17-2
14
17-1
4-3
4-6 4-5
4-2
4-9
17-3
15
18
4-8
21
26
4-7
15
15-1
21-1
19
5
26-11
21-7
21-6
5-1
26-7
26-3
21-2
26-15
26-8
21-3
26-12
26-13
26-16
26-14
21-4
5-2
26-9
26-9
21-5
5-3
26-10
26-4
20
5-4
26-1
24
24-2
24-1
6
26-9
7
25
25-2
7-1
25-1
7-2
11
7-3
7-4
23
79
26-5
26-6
Illustrated Parts Catalog.
■ Parts List of Refrigerator
NO
CODE-NO
PART NAME
1
2
3
4
4-1
4-2
4-3
4-4
4-5
4-6
4-7
4-8
4-9
5
5-1
5-2
5-2
5-4
6
7
7-1
7-2
7-3
7-4
8
9
10
11
12
13
13-1
13-2
13-3
13-4
13-5
13-6
13-7
14
15
15
15-1
16
17
17-1
17-2
17-3
18
18-1
18-2
DA67-00149A
DA97-00199L
DA97-01454A
DA97-01413A
DA97-01412A
DA97-01411A
DA63-01783A
DA61-01207A
DA41-00108A
6002-000462
DA39-00215A
DA32-10109X
6009-001293
DA67-00184C
DA63-00175A
DA63-00177C
DA67-00152A
DA64-00085A
DA63-10942B
DA67-00185C
DA63-00175A
DA63-00177C
DA67-00153A
DA64-00085A
DA63-01638A
DA63-00178A
DA63-00162B
6002-000215
4713-001132
DA97-01420A
DA63-00158A
DA72-00144A
DA62-00566A
DA62-00566B
DA62-00587A
DA47-00025H
DA32-10105H
DA67-40250E
DA67-00711A
DA67-00145A
DA71-20252A
DA34-10110B
DA96-00013H
DA32-00006B
DA47-10148J
DA61-00453A
DA47-00039B
DA47-00038B
DA70-00231A
SHELF-REF UPP
ASSY SHELF-FOLD
ASSY SHELF REF-LOW
ASSY CASE-CONVERTIBLE
ASSY CASECONVERTIBLE,
ASSY TRAY-CONVERTIBLE
GASKET-CONVERTIBLE
CASE-CONTROL CONV
PBA SUB
SCREW-TAPPING
WIRE HARNESS
SENSOR ASSY
SCREW-SPECIAL
CASE-VEG UPP ASSY
COVER-FRONT
COVER-FRONT REF,B
CASE-VEG
KNOB-MOIS CONT
COVER-VEG,LOW
CASE-VEG LOW ASSY
COVER-FRONT
COVER-FRONT REF,B
CASE-VEG
KNOB-MOIS CONT
COVER-LAMP REF
COVER-SENSOR
COVER SENSOR-B
SCREW-TAPPING
LAMP-INCANDESCENT
ASSY COVER-MULTI REF
COVER-MULTI
INSULATION
SEAL-MULTI REAR,L
SEAL-MULTI REAR,R
SEAL-MULTI AL,UPP
LAMP HOLDER
SENSOR-ASSY
TRAY-UTILITY
SHELF WIRE-WINE,RACK
SHELF-WINE
FIXER-GROMMET DOOR
SWITCH-DOOR
ASSY EVAP-REF
SENSOR ASSY
THERMO FUSE-ASSY
FIXER-SENSOR
HEATER-DRAIN ASSY,REF
HEATER-DRAIN,REF
Spec
GLASS
GLASS
HIPS
CONVERTIBLE
SUB CONVERTIBLE
CONVERTIBLE
SF-PVC
ABS-SCRAP
CONVERTIBLE
PH,+,2,M3.0,L10,ZPC(YEL),M
5V , CONVERTIBLE
STS304,-,PWH,+,M4,L15.5
HIPS
GPPS
PP
ABS
HIPS
GPPS
PP
ABS
PP
ABS
PP
GPPS
ABS , PNC2
TH,+,1,M4.0,L16,ZPC(YEL)
240V , 30W
PP
FOAM-PE
T2.0
T2.0
POAM-PE
E 14,250V,1A,370,NTR,PBT 5VA
502AT,K-PJT,-10~35,5V,5KOHM
GPPS
MSWR10
HIPS
ABS
-,125/1.5A.25,-,-,-,WHT,-,230V , 110W
PX-41C RD SEN , -10°C ~
SW-102T,250V
PP
240V
240V
SBHG1 , T0.6
80
Quantity
1
1
1
1
1
1
1
1
1
5
1
1
2
1
1
1
1
1
2
1
1
1
1
1
1
2
2
15
3
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
Remark
Illustrated Parts Catalog.
■ Parts List of Refrigerator
NO
CODE-NO
PART NAME
19
20
21
22
23
24
24-1
24-2
25
25-1
25-2
26
26-1
26-2
26-3
26-4
26-5
26-6
26-7
26-8
26-9
26-10
26-11
26-12
26-13
26-14
26-15
26-16
27
28
DA97-00724A
DA29-00003A
DA97-00725C
DA63-00586A
DA74-00056F
DA63-00365C
DA63-00163A
DA02-90106K
DA63-00366C
DA63-01643A
DA02-90106K
DA97-01419A
DA63-01636A
DA62-00505A
DA62-00506A
DA31-00043A
DA61-00413A
DA62-00567A
DA62-00568A
DA62-00614A
6002-000215
DA61-00417A
DA63-00713A
DA31-00016A
DA31-00020J
DA39-00060B
DA61-20128A
DA63-00423A
DA61-01205A
DA61-01206A
ASSY-COVER FILTER
FILTER-WATER ASS'Y
ASSY CASE-FILTER
COVER-TUBE FILTER
TANK WATER-ASSY
ASSY-COVER PURIFIER,L
COVER-PURIFIER L
CATALYST-LTC
ASSY-COVER PURIFIER,R
COVER-PURIFIER R
CATALYST-LTC
ASSY COVER-EVAP REF
COVER-EVAP REF
INSULATION DUCT-REF,A
INSULATION DUCT-REF,B
MOTOR-DAMPER
FIXER-AIR GUIDE
SEAL-COVER EVAP
SEAL-AIR REF,UPP
SEAL CUTT FOAM,LEX
SCREW-TAPPING
CASE MOTOR
COVER-MOTOR
FAN-CIRCUIT
MOTOR DC-BLDC(SENSOR)
WIRE HARNESS-MOTOR
SPRING ETC-FAN
GROMMET-MOTOR,BLDC
SUPPORT-SHELF REF,L
SUPPORT-SHELF REF,R
Spec
PP
HD-PE
Quantity
1
1
1
1
1
1
ABS
SS400-10-3
1
ABS
SS400-10-3
PP
FOAM-PS
FOAM-PS
NSBA001TA1,AT-PJT,MAX 60MA
PP
FOAM-PE + AL(30um)
OJC-3000 , T5
SPONGE , T5
TH,+,1,M4.0,L16,ZPC(YEL),M
ABS-SCRAP
PP
DREP3020LB,AT(F,R)
STS27 , PI7.8 ,ID1.0
NBR
HIPS
HIPS
81
1
1
1
1
1
1
1
1
1
4
1
1
1
1
1
1
2
1
1
Remark
12 . Illustrated Parts Catalog.
12-4) Unit Exploded View (RS21N, RS21H, RS21D, RS21F, RS23N, RS23H, RS23D, RS23F)
1
45
46
43
47
44
42
41
40
1
39
38
32
33
2
31
1
34
6
4-1
7
30
3
4
36
1
35
1
27
4-2
5-1
28
28-2
5
5-2
29
28-1
19
15
26
15-4
15-6
15-3
20
15-7
8
21
15-2
22
23 24
18-1
25
18
15-5
18-2
9
17-3
17-4
10
17-5
13
11
13-2
17
13-1
17-2
13-3
12
17-1
13
6
13-2
13-1
14
16
13-3
12
7
1
6
16-1
37
16-3
1
82
16-2
Illustrated Parts Catalog.
■ Parts List of Unit Exploded View
NO
CODE-NO
PART NAME
1
2
3
4
4-1
4-2
5
5-1
5-2
6
7
8
8-1
8-2
8-3
8-4
8-5
8-6
9
9-1
9-2
9-3
9-4
9-5
9-6
10
11
12
13
13-1
13-2
13-3
14
15
15-1
15-2
15-3
15-4
15-5
15-6
15-7
16
16-1
16-2
16-3
17
17-1
17-2
17-3
6002-000213
DA63-01379B
DA63-01380B
DA97-00585B
DA61-00051E
DA97-01497A
DA97-00586B
DA61-00052G
DA97-01497A
DA60-10124A
6002-000215
DA97-00165G
6003-001435
6011-001442
6021-001125
DA61-00096J
DA66-90113B
DA97-01494A
DA97-00166E
6003-001435
6011-001442
6021-001125
DA61-00095G
DA66-90113B
DA97-01494A
DA61-00317A
6009-001255
DA61-30102C
DA61-00056A
DA60-90124A
DA61-40115A
DA71-00064A
DA63-00189B
DA97-01283A
DA61-00415A
DA31-00020H
DA63-01146A
DA63-00713A
DA96-00042A
6501-000122
6002-000480
DA97-00555B
DA71-00058A
DA61-40126B
DA60-90146A
DA97-01285A
DA66-00034A
6009-001252
DA97-00259E
SCREW-TAPPING
COVER HINGE-UPP,L
COVER HINGE-UPP,R
ASSY HINGE-UPP,L
HINGE-UPP,L
ASSY-SHIM HINGE UPP
ASSY HINGE-UPP,R
HINGE-UPP,R
ASSY-SHIM HINGE UPP
SCREW-TAP TITE
SCREW-TAPPING
ASSY HINGE-LOW,L
SCREW-TAPTITE
BOLT-SOCKET
NUT-HEXAGON
HINGE-LOW,L
CAM HINGE-RISER,UPP
ASSY-SHIM HINGE LOW
ASSY HINGE-LOW,R
SCREW-TAPTITE
BOLT-SOCKET
NUT-HEXAGON
HINGE-LOW, R
CAM HINGE-RISER,UPP
ASSY-SHIM HINGE LOW
BRACKET-HINGE,LOW
SCREW-HEX
FOOT-FRONT
CASTER-FRONT ASSY
RIVET
CASTER-FRONT
REINF-CASTER-FRONT
COVER-LEG-FRONT
ASSY SUPPORT-CIRCUIT MOTOR
SUPPORT-CIRCUITE MOTOR
MOTOR DC-BLDC
GROMMET-MOTOR
COVER-MOTOR
ASSY-HARNESS COMP
CABLE TIE
SCREW-TAPPING
ASSY CHASSIS-COMP
CHASSIS-COMP
CASTER-REAR
PIN-CASTER
ASSY TRAY-DRAIN WATER
TRAY-DRAIN WATER
SCREW-SPECIAL
ASSY PIPE-SPIRAL COND
Spec
TH,+,1,M4,L12,ZPC(YEL)
ABS
ABS
SHP1 , T3.0
RD-PVC
SHP1 , T3.0
RD-PVC
M6 ,L16,HH,ZPC2
TH,+,1,M4.0,L16,ZPC(YEL)
T4.5 , SHP1
M5,L12.7,ZPC(YEL)
M8,L15,ZPC(BLK),SCM435
3,M8, P1.25,ZPC(BLK),SWRCH10
SHP1 , SM45
NY-66(2110R)
T1.5 , RD-PVC
T4.5 , SHP1
M5,L12.7,ZPC(YEL)
M8,L15,ZPC(BLK),SCM435
3,M8, P1.25,ZPC(BLK),SWRCH10
SHP1 , SM45
NY-66(2110R)
T1.5 , RD-PVC
SHP1
SWRCH18A,-,HEX-PLANGE,HEX,
PP
SCP1
MSWR10,OD6.0,L56,ZPC3
NY-66
SCP1 , T2.6
HIPP
MOTOR
ABS SCRAP
DRCP3030LA , 0.259A
NBR
PP
350mm
DACT-100,-,W2.5,L101.6,NTR
M4,L10,ZPC(YEL)
SBHG1 , T1.4
PP
MSWR10,OD6.0,L40,ZPC2
SWRCH18A,-,PH,+,M4.0,L20
SPIRAL
83
Quantity
12
1
1
1
1
1
1
1
1
6
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
M6,L 8
2
2
1
1
1
1
1
1
1
2
1
1
1
1
1
1
2
2
1
1
4
1
Remark
Illustrated Parts Catalog.
■ Parts List of Unit Exploded View
NO
CODE-NO
PART NAME
17-4 DA63-40128A GROMMET-SUB COND
17-5 DA62-00440A SEAL-SUB COND
18 DA31-00010C FAN-ASS'Y
18-1 DA31-00015B FAN-TURBO
18-2 DA61-20128A SPRING ETC-FAN
19 MK4A5QR1U/EØ1 COMPRESSOR
20 DA73-30102B DRYER-ASSY
21 DA63-40004A GROMMET-COMP
22 DA34-10003V RELAY PROTECTOR O/L
23 DA35-10013B RELAY-PTC
24 DA63-10352A COVER-RELAY
25 DA39-00084B WIRE HARNESS COMP
26 DA60-20008A BOLT-HEX
27 DA97-00918A ASSY PIPE CONNECT
28 DA97-00359A ASSY TUBE-DRAIN
28-1 DA62-20001R TUBE PVC
28-2 DA63-00951C GROMMET-DRAIN HOSE
29 DA62-20001P TUBE PVC
30 DA63-00278E COVER COMP-ASSY
31 DA61-00261A CASE PCB-PANEL
32 DA63-00783A COVER PCB-PANEL
33 DA41-00185B PBA MAIN
33 DA41-00185A PBA MAIN
33 DA41-00195A PBA MAIN
34 DA27-00002A COIL
2501-001186 C-OIL
35
36 DA71-00155B FIXER-MAIN PCB
37 DA74-00038C DUCT-CABI,C
38 DA74-40149C VALVE WATER-ASSY
40 DA73-00070V PIPE-WATER LINE
41 DA60-30104A NUT-WATER LINE
42 DA71-20208A FIXER-VALVE WATER
43 DA73-00134A PIPE-WATER FRE,ASSY(SUB)
44 DA72-00228C SEAL-WATER PIPE
45 DA97-00979A ASSY COVER-PIPE WATER
46 DA63-01701A GROMMET-TUBE WATER,FILL
47 DA47-00035A HEATER--WATER,PIPE
Spec
NBR
FOAM-PE , T5.0
_150
ABS
STS27 , PI7.8, ID1.0
15.31cc,220/240V~50Hz,RSCR
CU,OD18.85,ID2,L102,10.0G
NBR
4TM265RHBYY-53,
J531Q35E330M385-2,385V.6A
PP
-,-,EXP,-,-,-,COMP,NOTHING,
SM30C
SOFT-PVC , T1.0 , L21
SOFT-PVC , T1.0 , L21
NBR
SOFT-PVC , T1.0 , L21
SBHG1 , T0.35
ABS
ABS
ET-R600a,-,FR-4,1.6T*163*197,D
ET-R600a,-,FR-4,1.6T*163*197,D
ET-R600a,-,FR-4,1.6T*163*197,D
4,+50%,-30%,38*50
5UF,350V,BK,43X55MM,15
RD-PVC , T1.5
ABS SCRAP
RIV-12A-4
PB(4137) , Ø6.35
NY-6
NY-6
SUB)AL , Ø1.0
FOAM-PE , T10 , L80
240V , 7W
IN SILICON
240V , 7W
84
Quantity
2
1
1
1
1
1
1
4
1
1
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Remark
12 . Illustrated Parts Catalog.
12-5) Freezer Room Exploded View (RS21D, RS21F, RS21J, RS21K, RS23D, RS23F, RS23J, RS23K)
13
5-27
5-12
5-11
15
14
5-26
5-24
5-25
16
5-13
17
5-18
5-23 5-17
5
5-8
5-7
5-2
5-1
5-9 5-21
5-22
18
5-6
5-20
5-3
5-4
5-14
19-3
19-2
5-19
19-4
19
19-1
6-10
6-8
19-7
6-1
6
6-7
19-5
19-6
20
21
6-9
6-4
15
6-6
6-3
23
6-2
15
27
22
24-5
24-3
1
24-9
24-7
1-2
24-10
24-2
24-1
1-3
1-1
24-8
24-10
24-11
24-6
24
2
2-2
2-3
2-1
2
2-2
25
2-3
2-1
25-2
25-1
4
4-1
26
4-2
3-1
3-2
3
4-3
25-3
3-3
85
Illustrated Parts Catalog.
■ Part List of Freezer Room
NO
CODE-NO
PART NNAME
1
1-1
1-2
1-3
2
2-1
2-2
2-3
3
3-1
3-2
3-3
4
4-1
4-2
4-3
5
5-4
5-2
5-3
5-5
5-1
6
6-1
6-2
6-3
6-4
6-5
6-6
6-7
6-8
6-9
6-10
6-11
13
14
15
16
17
17
18
19
19-1
19-2
19-3
19-4
19-5
19-6
19-7
20
DA67-00180A
DA67-00175A
DA67-00177B
DA64-00090A
DA67-00181A
DA67-00146A
DA67-00177C
DA64-00090A
DA67-00182C
DA67-00150A
DA63-00174C
DA63-00170A
DA67-00183C
DA67-00151A
DA63-00174C
DA63-00170A
DA59-00136E
DA60-40116A
DA63-00180A
DA63-00181B
DA63-10016A
DA66-00033A
DA61-00143C
DA67-00144B
DA61-20140A
DA71-00163A
DA70-20017A
DA65-20107A
DA47-40112V
6001-000033
DA31-10141D
DA39-00083A
DA74-40151F
DA63-90008A
DA71-20252A
DA59-30103J
6002-000215
6002-000471
DA67-40308A
DA67-40334A
DA34-10121A
DA97-00101J
DA63-00363A
DA72-00245A
DA72-00158F
DA72-00159E
DA62-00219A
DA70-00215B
DA32-10105H
DA63-00178A
SHELF-FRE ASSY
SHELF-FRE
SHELF GLASS
TRIM-SHELF
SHELF-FRE ASSY
SHELF-FRE
SHELF GLASS
TRIM-SHELF
CASE-BASKET UPP ASSY
CASE-BASKET
COVER-FRONT FRE,B
COVER-FRONT
CASE-BASKET LOW ASSY
CASE-BASKET
COVER-FRONT FRE,B
COVER-FRONT
CRUSHER ICE ASSY
WASHER-PLAIN
COVER-ICE BUCKET
COVER-ICE BUCKET,B
COVER-CRUSHER DISP
TRAY-ICE
CASE-AUGER MOTOR,ASSY
CASE-AUGUR MOTOR
SPRING ETC-SOLENOID
FIXER-NUT
PLATE-D/AUGER DISP
SADDLE-SOLENOID
LAMP HOLDER
SCREW-MACHINE
MOTOR GEARD
WIRE HARNESS-SUB
VALVE-SOLENOID
BUSH-SOLENOID
FIXER-GROMMET DOOR
ICE MAKER
SCREW-TAPPING
SCREW-TAPPING
TRAY-ICE
TRAY-ICE
SWITCH-DOOR
ASSY COVER-MULTI FRE
COVER EVAP-FRE,FRONT UPP
INSULATION DUCT-FRE,UPP
SEAL EVAP-FRONT FRE,L
SEAL EVAP-FRONT,FRE R
SEAL-AIR FRE,UPP
PLATE-INS,DUCT
SENSOR-ASSY
COVER-SENSOR
Spec
GLASS-SHELF
HIPS
GLASS
PVC
GLASS-SHELF
HIPS
GLASS
PVC
HIPS
HIPS
HIPS
HIPS
HIPS
HIPS
STS4
PP
GPPS
PC
ABS SCRAP
STS304
STS420-J2 , T1 , CLIP
STS304 , L127XD14.4
NY-6
PBT 5VA , E14
TH,+,M4,L10,-,STS304
ISG-3250SSD,SR-S6586,1.8A,50
POM
ABS
DC12V
TH,+,1,M4.0,L16,ZPC(YEL)
TH,+,1,M4,L12,PASS,STS304
PP , T1.0
PP , T1.0
PA6
PP
FOAM-PS
T2.0
T2.0
OJC-3000 , T7.0
RD-PVC , T1.2
502AT,K-PJT,-10~35,5V,5KOHM
GPPS
Quantity
1
1
1
2
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
2
1
15
2
1
1
1
1
1
1
1
1
1
2
1
2
Remark
Illustrated Parts Catalog.
■ Part List of Freezer Room
NO
CODE-NO
PART NAME
21
22
23
24
24-1
24-2
24-3
24-4
24-5
24-6
24-7
24-8
24-9
24-10
24-11
25
25-1
25-2
25-3
26
26-1
26-2
27
DA63-00162B
4713-001132
DA63-00364A
DA97-00360P
DA63-00153B
DA62-00186A
DA72-00227A
DA61-00417A
DA63-00713A
DA31-00038A
DA31-00020E
DA39-00060B
DA63-01146A
6002-000471
DA61-20128A
DA96-00090B
DA32-00006B
DA47-10148J
DA61-00603A
DA97-00339B
DA47-00092B
DA70-00404A
DA63-00157A
COVER SENSOR-B
LAMP-INCANDESCENT
COVER LAMP-FRE,A
ASSY COVER EVAP-FRE LOW)
COVER EVAP-FRE(FRONT LOW)
INSULATION DUCT-FRE
SEAL-AIR FRE LOW
CASE MOTOR
COVER-MOTOR
FAN-CIRCUIT
MOTOR DC-BLDC,SENSOR
WIRE HARNESS-MOTOR
GROMMET-MOTOR
SCREW-TAPPING
SPRING ETC-FAN
ASSY EVAP-FRE
SENSOR ASSY
THERMO FUSE-ASSY
FIXER-SENSOR
ASSY-PLATE DRAIN,FRE
HEATER DRAIN-FRE
PLATE-DRAIN FRE
COVER-LAMP
Spec
Quantity
PP
FOAM-PS
OJC-3000 , T5
ABS SCRAP
PP
ABS
DREP3020LA,ET,0.245
F-FAN
NBR , ID6.5 , OD42
TH,+,1,M4,L12,PASS,STS304
STS27 , PI7.8 , ID1.0
230V
PX-41C RD SEN,A TOP,-10°C~
SW-102T , 250V
PP
230V , 41W
230V , 41W
GALVALUME , T0.5
GPPS
2
3
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
ABS , PNC-2
240V , 30W
PP
87
Remark
12 . Illustrated Parts Catalog.
12-6) Freezer Room Door Exploded View
9
9-1
9-2
9-3 9-4
9-6
9-5
9-7
14
9-8
1
13
12-2
2
8
6
10
12
16
12-1
18
15
17
11-1
7
11-2
11
3
4
88
5
Illustrated Parts Catalog.
■ Part List of Freezer Room Door Exploded View
NO
CODE-NO
1
2
3
4
5
6
7
8
9
9-1
9-2
9-3
9-4
9-6
9-7
9-8
10
11
11-1
11-2
12
12-1
12-2
13
14
15
16
17
18
DA63-30231K
DA61-00776A
DA66-90112C
6002-000468
DA63-00213C
DA63-01311A
6002-000468
DA97-00191S
DA63-00971D
DA63-01168C
DA64-00740B
DA61-00875A
DA41-00174A
DA63-00970A
6002-000466
DA64-00096B
DA64-00111B
DA64-00095B
DA71-00078A
DA64-00209A
DA64-00098B
DA64-00196A
DA64-00097B
DA64-00100E
DA64-00099B
DA71-00077A
6002-000213
6002-000470
PART NAME
ASSY DOOR FOAM FRE
GASKET DOOR-FRE ASSY
STOPPER DOOR
CAM HINGE-RISER,LOW
SCREW-TAPPING
GUARD-FRE,UPP
GUARD BOTTLE-FRE LOW
SCREW-TAPPING
ASSY-COVER-CONTROL
COVER-CONTROL FRONT
COVER-CONTROL BASIC
KNOB-TOUCH,B
SUPT-KNOB TOUCH,BASIC
PBA PANEL
COVER-PCB REAR
SCREW-TAPPING
HANDLE BASE-MID
HANDLE-LOW-ASSY
HANDLE BASE-LOW
REINF-HANDLE LOW
HANDLE TRIM-ASSY,MID
HANDLE TRIM-MID
TRIM-HANDLE CONNECT,MID
HANDLE BASE-UPP
HANDLE-TRIM UPP
HANDLE TRIM-LOW
REINF-HANDLE-MID
SCREW-TAPPING
SCREW-TAPPING
Spec
SF-PVC
SHP1 , T3.0
NY-66
PH,+,2S,M5.0,L18,ZPC(YEL)
PP
PP
PH,+,2S,M5.0,L18,ZPC(YEL)
ABS , SNOW-WHITE
GPPS
ABS , SNOW-WHITE
SILICONE
1.6*190*70
ABS , SNOW-WHITE SCRAP
PH,+,2S,M3.O,L8,ZPC(YEL)
HIPP , SNOW-WHITE
ABS , SNOW-WHITE
HIPP , SNOW-WHITE
ABS , SNOW-WHITE
ABS , SNOW-WHITE
ABS , SNOW-WHITE
SILVER COLOR
HIPP , SNOW-WHITE
ABS , SNOW-WHITE
ABS , SNOW-WHITE
SBHG1 , T1.4
TH,+,1,M4,L12,ZPC(YEL),SWR
TH,+,1,M4,L10,ZPC,SCRCH18A
89
Quantity
1
1
1
1
4
1
5
4
1
1
1
4
2
1
1
4
1
1
1
1
1
1
2
1
1
1
1
3
3
Remark
12 . Illustrated Parts Catalog.
12-7) Freezer Room Door Exploded View (RS21D, RS21F, RS21J, RS21K, RS23D, RS23F, RS23J, RS23K)
10-1
10-2
10-5
10
10-3
11
17
14
14-1
14-2
10-4
10-6
11-1
16
11-2
13-2
17
15-1
12
13
18
13-1
23
15
1
22
7
21-2
28
6
2
19
21
25
21-1
8
27
24
26
20-1
20-2
20
9
3
4
5
90
Illustrated Parts Catalog.
■ Part List of Freezer Room Door Exploded View
NO
CODE-NO
PART NAME
1
ASSY DOOR FOAM FRE
2
DA63-30231K GASKET DOOR-FRE ASSY
3
DA61-00776A STOPPER DOOR
4
DA66-90112C CAM HINGE-RISER,LOW
5
6002-000468 SCREW-TAPPING
6
DA67-00163B CAP-CHUTE,ICE
7
DA72-00262A CUSHION-GUIDE ICE CHUTE
8
DA63-00213C GUARD-FRE,UPP
9
DA63-01311A GUARD BOTTLE-FRE LOW
10 DA97-01345A ASSY COVER-DISPENSER
10-1 DA63-01608A COVER DISPENSER
10-2 DA64-00740B KNOB-TOUCH
10-3 DA61-00874A SUPPORT-KNOB TOUCH,DISP
10-4 DA63-01169H COVER-CONTROL DISP
10-5 DA41-00173B PBA PANEL
10-6 6002-000466 SCREW-TAPPING
11 DA97-01346A ASSY COVER-PCB,PANEL REAR
11-1 DA63-01609A COVER-PCB PANEL,REAR
11-2 DA34-00011A SWITCH-MICRO
12 DA66-00037G TRAY DISPENSER
13 DA97-01350A ASSY LEVER-DISPENSER,ICE
13-1 DA66-00236A LEVER-DISPENSER,ICE
13-2 DA61-00088A SPRING ETC-DISPENSER ICE-LEVER
14 DA97-01352A ASSY LEVER-DISPENSER,WATER
14-1 DA66-00237A LEVER-DISPENSER WATER
14-2 DA61-00338A SPRING ETC-WATER LEVER,DISP
15 DA97-00283A ASSY COVER-ICE ROUTE
15-1 DA71-00073A STOPPER-LEVER DISPENSER
16 DA61-70234A SUPPORT-TIME DELAY
17
6002-000471 SCREW-TAPPING
18 DA74-40154C VALVE SOLENOID
19 DA64-00096B HANDLE BASE-MID
20 DA64-00111B HANDLE-LOW,ASSY
20-1 DA64-00095B HANDLE BASE-LOW
20-2 DA71-00078A REINF-HANDLE,LOW
21 DA64-00209A HANDLE TRIM-ASSY,MID
21-1 DA64-00098B HANDLE TRIM-MID
21-2 DA64-00196A TRIM-HANDLE CONNECT,MID
22 DA64-00097B HANDLE-BASE,UPP
23 DA64-00100E HANDLE-TRIM,UPP
24 DA64-00099B HANDLE-TRIM,LOW
25 DA71-00077A REINF-HANDLE,MID
26
6002-000213 SCREW-TAPPING
27
6002-000470 SCREW-TAPPING
28
6002-000468 SCREW-TAPPING
Spec
SNOW WHITE
SF-PVC
SHP1,T3.0
NY-66(2110R)
PH,+,2S,M5.0,L18,ZPC(YEL),
ABS , SNOW-WHITE
SILICON
HI-PP
HI-PP
SNOW-WHIT
ABS , SNOW-WHITE
ABS , SILVER COLOR
SILICON
ABS , SNOW-WHITE
10mm
PH,2S,M3.O,L8,ZPC(YEL)
REAR ,SNOW
PP,SNOW WHITE
VP533A-OF-5,MICRO,250V,15A,
HIPS,SNOW-WHITE
SNOW-WHITE
ABS , SNOW-WHITE
STS304,
SNOW-WHITE
ABS , SNOW-WHITE
STS304
SNOW-WHITE
POM
HIPS
TH,+,1,M4,L12,STS304,
USD-DPS4
HIPP , SNOW-WHITE
SNOW-WHITE
HIPP , SNOW-WHITE
SBHG1,T1.4
ABS , SNOW-WHITE
ABS , SNOW-WHITE
SILVER COLOR
HIPP , SNOW-WHITE
ABS , SNOW-WHITE
ABS , SNOW-WHITE
SBHG1,T1.4
TH,+,1,M4,L12,ZPC(YEL),SWR
TH,+,1,M4,L10,ZPC,SCRCH18A
PH,+,2S,M5.0,L18,ZPC(YEL),
91
Quantity
1
1
1
1
4
1
1
1
3
1
1
6
2
1
1
4
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
3
3
4
Remark
12 . Illustrated Parts Catalog.
12-8) Refrigerator Room Door Exploded View
1
14
6
13
6-2
6-1
12-2
2
19
12-1
16
12
10
8
7
17
11-2
11
11-1
7
3
4
5
92
15
Illustrated Parts Catalog.
■ Part List of Refrigerator Room Door Exploded View
NO
CODE-NO
1
2
3
4
5
6
6-1
6-2
7
8
9
10
11
11-1
11-2
12
12-1
12-2
13
14
15
16
17
18
19
DA63-30232K
DA61-00776A
DA66-90112C
6002-000468
DA97-00904A
DA63-00199B
DA73-00216A
DA63-00635A
DA71-00090A
DA63-00590A
6002-000470
DA64-00111B
DA64-00095B
DA71-00078A
DA64-00209A
DA64-00098B
DA64-00196A
DA64-00097B
DA64-00100E
DA64-00099B
DA71-00077A
6002-000213
6002-000468
DA64-00096B
PART NAME
ASSY DOOR FOAM REF
GASKET DOOR-REF ASSY
STOPPER DOOR
CAM HINGE-RISER,LOW
SCREW-TAPPING
ASSY COVER-GUARD
COVER-GUARD
RUBBER-COVER GUARD
GUARD BOTTLE-REF,UPP
GUIDE-BOTTLE REF
GUARD REF-LOW
SCREW-TAPPING
HANDLE-LOW-ASSY
HANDLE BASE-LOW
REINF-HANDLE LOW
HANDLE TRIM-ASSY,MID
HANDLE TRIM-MID
TRIM-HANDLE CONNECT,MID
HANDLE BASE-UPP
HANDLE-TRIM UPP
HANDLE TRIM-LOW
REINF-HANDLE-MID
SCREW-TAPPING
SCREW-TAPPING
HANDLE BASE-MID
Spec
SF-PVC
SHP1 , T3.0
NY-66
PH,+,2S,M5.0,L18,ZPC(YEL)
GPPS
SILICONE
HIPP
PP
HIPP
TH,+,1,M4,L10
SNOW-WHITE
HIPP , SNOW-WHITE
SBHG1 , T1.4
ABS , SNOW-WHITE
ABS , SNOW-WHITE
SILVER COLOR
HIPP , SNOW-WHITE
ABS , SNOW-WHITE
ABS , SNOW-WHITE
SBHG1 , T1.4
TH,+,1,M4,L12,ZPC(YEL)
PH,+,2S,M5.0,L18,ZPC(YEL)
HIPP , SNOW-WHITE
93
Quantity
1
1
1
1
4
1
1
2
2
1
2
3
1
1
1
1
1
2
1
1
1
1
3
4
1
Remark
12 . Illustrated Parts Catalog.
12-9) Refrigerator Room Door Exploded View (RS21H, RS21F, RS21K, RS23H, RS23F, RS23K)
10
14
13
12
12-1
12-2
12-3
18
1
18
6
2
17-2
18
6-2
6-1
15
17
21
23
8
17-1
20
11
21
7
16-1
16-2
16
3
4
9
5
94
Illustrated Parts Catalog.
■ Part List of Refrigerator Room Door Exploded View
NO
CODE-NO
1
2
3
4
5
6
6-1
6-2
7
8
9
10
11
12
12-1
12-2
12-3
13
14
15
16
16-1
16-2
17
17-1
17-2
18
19
20
21
22
23
24
DA63-30232K
DA61-00776A
DA66-90112C
6002-000468
DA97-00904A
DA63-00199B
DA73-00216A
DA63-00635A
DA71-00090A
DA63-00590A
DA97-01347A
DA63-00224A
DA63-00877A
DA63-00222A
DA63-00223A
DA63-40167A
DA63-01607A
DA63-00225A
DA64-00096B
DA64-00111B
DA64-00095B
DA71-00078A
DA64-00209A
DA64-00098B
DA64-00196A
DA64-00097B
DA64-00100E
DA64-00099B
DA71-00077A
6002-000213
6002-000468
6002-000470
PART NAME
ASSY DOOR FOAM REF
GASKET DOOR-REF ASSY
STOPPER DOOR
CAM HINGE-RISER,LOW
SCREW-TAPPING
ASSY COVER-GUARD
COVER-GUARD
RUBBER-COVER GUARD
GUARD BOTTLE-REF,UPP
GUIDE-BOTTLE REF
GUARD REF-LOW
ASSY HOME BAR
GASKET-HOME BAR IN
COVER DOOR-RECESS,ASSY
COVER-DOOR RECESS-OUT
COVER-DOOR RECESS-IN
GROMMET-COVER CHIL
COVER-BRACKET FRAME
GASKET-HOME BAR-OUT
HANDLE BASE-MID
HANDLE-LOW-ASSY
HANDLE BASE-LOW
REINF-HANDLE LOW
HANDLE TRIM-ASSY,MID
HANDLE TRIM-MID
TRIM-HANDLE CONNECT,MID
HANDLE BASE-UPP
HANDLE-TRIM UPP
HANDLE TRIM-LOW
REINF-HANDLE-MID
SCREW-TAPPING
SCREW-TAPPING
SCREW-TAPPING
Spec
SF-PVC
SHP1 , T3.0
NY-66
PH,+,2S,M5.0,L18,ZPC(YEL)
GPPS
SILICONE
HIPP
PP
HIPP , SNOW-WHITE
SNOW-WHITE
SF-PVC
GPPS
GPPS
GPPS
T3.0 , SILICON
SNOW-WHITE
SF-PVC
HIPP , SNOW-WHITE
ABS , SNOW-WHITE
HIPP , SNOW-WHITE
SBHG1 , T1.4
ABS , SNOW-WHITE
ABS , SNOW-WHITE
SILVER COLOR
HIPP , SNOW-WHITE
ABS , SNOW-WHITE
ABS , SNOW-WHITE
SBHG1 , T1.4
TH,+,1,M4,L12,ZPC(YEL)
PH,+,2S,M5.0,L18,ZPC(YEL)
TH,+,1,M4,L10,ZPC,SCRCH18A
95
Quantity
1
1
1
1
4
1
1
2
2
1
2
1
1
1
1
1
2
1
1
1
1
1
1
1
1
2
1
1
1
1
3
4
3
Remark
13. Machine Room Assembly Specification
13-1) Please remove fixed screw of cover of machine room of Refrigerator rear low part.
13-2) Machine Room Assembly Specification
Electric Field Box
Condensing Unit
Cooling Fan
Compressor
Dryer
96
14. Disassembly & Assembly Method of Internal Part of Electric Field Box
14-1) Please cut-off the power supply of refrigerator.
14-2) Please deviate cover of electric field box using driver.
(+) driver
(-) driver
14-3) Assembly Specification of Electric Field Box
C-OIL
PCB-MAIN ASSY
97
ELECTRONICS
272, Oseon-Dong, Kwangsan-Gu,
Kwangju-City, Korea, 506-723
TEL : 82-62-950-6896,6193
FAX : 82-62-950-6829
- This Service Manual is a property of Samsung Electronics Co., Ltd.
Any unauthorized use of Manual can be punished under applicable
International and/or domestic law. -
© Samsung Electronics Co., Ltd.
Refrigerator Division 2003. 5
Printed in Korea
Code : DA82-00001C