advertisement
Z-1520 RGB
Fog Machine User Manual
文管中心
2014.02.21
正式發行章
English
© 2014 Antari Lighting and Effects Ltd.
1
User Manual - English
Safety Information
Please read the following safety information carefully before operating the machine. Information includes important safety information about installation, usage, and maintenance. Pay attention to all warning labels and instructions in this manual and printed on the machine.
If you have questions about how to operate the machine safely, please contact your local
Antari dealer for help.
․
․
․
․
․
․
․
․
․
․
․
․
Keep this device dry.
Always connect to a grounded circuit to avoid risk of electrocution.
Before connecting machine to power, always check voltage indicate on machine match to your local AC voltage. Do not use the machine if AC power voltage does not match.
Disconnect the machine from AC power before servicing and when not in use.
This product is for indoor use only! Do not expose to rain or moisture. If fluid is spilled, disconnect AC power and clean with a damp cloth. If fluid is spilled onto electronic parts, immediately unplug the machine and contact your local Antari dealer for advice.
No user serviceable and modifiable parts inside. Never try to repair this product, unauthorized technician may lead machine to damage or malfunction.
For adult use only. Never leave the machine running unattended.
Installed in well ventilated area. Provide at least 50 cm space around the machine.
Never add flammable liquid of any kind to the machine.
Make sure there are no flammable materials close to the machine while operating.
Only use Antari fluid. Other fluid may lead to heater clog and malfunction.
If the machine fails to work, unplug the machine and stop operation immediately.
Contact your local Antari dealer for advise.
2
․
․
Before transporting the machine, make sure the fluid tank is completely drained.
Smoke fluid may present health risks if swallowed. Do not drink smoke fluid. Store it securely. In case of eye contact or if fluid is swallowed immediately look for medical advice.
Unpacking and Inspection
Immediately upon receiving the machine, carefully unpack the carton, check all content to ensure that all parts are present and have been received in good condition. If any parts appear damaged or mishandled from shipping, notify the shipper immediately and retrain the packing material for inspection.
What is included:
1 x Z-1520 RGB Fogger
1 x W-2 Wireless Remote
1 x Power Cord
1 x User Manual
Product Dimension
295 mm
3
210 mm
418 mm
Product Overview
Tank Capacity : 2.5 liter
22 x 3W LED
(8R, 7G, 7B)
XLR 5-Pin DMX Connector
XLR 3-Pin DMX Connector
PowerCon
Breaker
Wireless Receiver
LCD Control Panel
Setting Up
Step 1: Place the machine on a flat surface and in a suitable large area with at least 50 cm open space around the machine.
Step 2: Fill the fluid tank with Antari approved fluid.
Step 3: Connect the machine to suitable rated power supply. To determine the power requirement for the machine refer to the label on the back of the machine.
Always connect the machine to a protected circuit and ensure it is properly grounded to avoid risk of electrocution.
Step 4: Turn on the machine and allow it to heat up. Heat up takes approximatly 5 mintues.
Once the machine has reached operating temperature, the LCD display will show “Ready To
4
Fog”. Now the machine is ready for operation.
Step 5: To start making fog, locate the Volume button on the control panel, and press the button to start making fog.
Step 6: To turn off the machine, press STOP button and turn Powercon to the OFF position.
Operation
Control Panel Operation
The machine can be operated with onboard digital control interface
ANTARI Z-1520 RGB
Ready to Fog
Button Function
[MENU]
▲
[UP]/[TIMER]
Scroll through setting menu
Up/Activate Timer function
▼
[DOWN]/[VOLUME] Down/Activate Volume function
[STOP] Deactivate Timer/Volume function
Control Menu
DMX512
Address: 1
Set DMX address from 1 to 504
Stand Alone
Set Master
Set machine as Master of Slave unit
5
Color Mode
On
Turn LED On or Off
Color Mode
Marco:01
Set LED output color from macro 1 to 10
Color Mode
Chase:01
Set LED chase from 1 to 15
Timer
Interval 15 Sec
Set interval from 15 to 360 seconds
Timer
Duration 5 Sec
Set duration from 1 to 5 seconds
Wireless Setting
On
Turn On or Off wireless control
Wireless Setting
Button A:M01
Set wireless remote button function macro color 1 to 10 or chase 1 to 15 and off.
Wireless Setting
Button B:M01
Set wireless remote button function macro color 1 to 10 or chase 1 to 15 and off.
Wireless Setting
Button C:M01
Set wireless remote button function macro color 1 to 10 or chase 1 to 15 and off.
Wireless Setting
Button D:M01
Set wireless remote button function macro color 1 to 10 or chase 1 to 15 and off.
6
LED Setting
Fog Only
Setting for LED to turn on with fog only or always on.
LED Fade Out
Delay: 0 Sec
Set LED delay time from 0 to 5 seconds.
Run Last Setting
On
Turn On/Off run last setting function
Wireless Operation
Wireless remote control system W-2 consist of a transmitter equipped with four buttons to activate four user configurable LED setting and fog; with an onboard receiver attach to the rear panel of Z-1520 RGB.
W-2 Wireless Transmitter
Wireless Receiver
Wireless settings are configurable through onboard control panel, refer to control menu
7
section to setup each buttons.
In a free open space the effective distance is 50 meters, actual usage depending on obstacle level the effective distance is 10-25 meters.
Registering transmitter
Transmitter can be pair or deleted from the receiver. Each receiver can pair up to 10 transmitters. Follow below steps to pair or delete transmitter from receiver.
Step 1: Power off Z-1520 RGB Fogger
Step 2: Press and hold [DOWN] button
Step 3: Turn power on and release [DOWN] button when LCD display blinks
Step 4: Follow the menu instruction to pair or delete transmitter
Transmitter battery replacement
If effective distance seems to be decreased, it is possible the battery level are low and require replacement. In order to replace the battery, undo the three screws on the back of transmitter to release the cover. Replace with same type and specification of battery which is
27A 12V
DMX Connector Pin Assignment
The machine provide 3 or 5 pin XLR connector for DMX connection. Diagram below indicate pin assignment information
8
Pin
1
2
3
DMX Channel Function
Channel 1
Fog
Channel 2
Red LED
Channel 3
Green LED
Channel 4
Blue LED
Channel 5
Chase
Channel 6
DMX Value Range
0 – 4
5 – 255
DMX Value Range
0-255
DMX Value Range
0-255
DMX Value Range
0-255
DMX Value Range
1-15
16-31
32-47
48-63
64-79
80-95
96-111
112-127
128-143
144-159
160-175
176-191
192-207
208-223
224-255
DMX Value Range
9
Function
Ground
Data-
Data+
Function
Fog Off
Fog On
Function
0-100%
Function
0-100%
Function
0-100%
Function
Chase 1
Chase 2
Chase 3
Chase 4
Chase 5
Chase 6
Chase 7
Chase 8
Chase 9
Chase 10
Chase 11
Chase 12
Chase 13
Chase 14
Chase 15
Function
Chase Speed
Channel 7
Master Dimmer
Channel 8
Strobe
Fluid
0-255
DMX Value Range
0-255
DMX Value Range
0-255
0-255 step per min
Function
0-100%
Function
1-20 Hz
Only use Antari FLC water-based liquid for the Z-1520 RGB Fogger. The machine is tested and calibrated with this liquid to get the best output performance. Warranty will be void if any other type of liquid is used, improper use of liquid may lead to machine failure and malfunction.
Service and Maintenance
․
․
․
․
․
․
Do not allow the machine to become contaminated.
Remove dust from air vents with air compressor, vacuum or a soft brush.
Only use a damp cloth to clean the casing.
Before storing run distilled water through the system to help avoid condensing the pump or heater.
It is recommended to run the machine on a monthly basis in order to achieve best performance and output condition.
Excessive dust, liquid and dirt built up will degrade performance and cause overheating.
Breaker Reset
Disconnect AC power before reset breaker. Only replace fuse with same type and rating.
10
Step 1: Disconnect AC power
Step 2: Flip breaker to ON position
Step 3: Turn on machine to test
Breaker
120V = 15A 250V
230V = 9A 250V
Technical Specifications
Input voltage
Breaker
Heater
Warm-up time
Coverage volume
Max. operating time
Fluid tank capacity
Fluid consumption
Compatible fluid
Control option
DMX channels
Power connection
DMX data connection
Dimension
Dry weight
120V 60Hz
230V 50Hz
120V = 15A 250V
230V = 9A 250V
1550W
5 min. (approx.)
Height 5 Meters, Width 1 Meter
8 seconds burst
2.4 L
25 ml/10 sec.
Antari FLC water-based fluid
DMX 512, Manual, Timer, Wireless remote
8 channels
Neutrik Powercon
3-pin and 5-pin XLR
L 418 x W 295 x H 210 mm
10.4 kg
11
C08Z15200
12
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project