WebGate C1080BL-IR48-AF User manual

1. Check Frame rate setting based on power frequency
- Set Frame rate to 25Hz if your region is using 50Hz(PAL) power frequency, or set to
30Hz for 60Hz(NTSC) region. (OSD : System  Frame rate).
2. Focus setup
To aviod losing focus at night time, please adjust camera focus as follows.
1) Move Tele, Wide to adjust Zoom and Near, Far to adjust Focus.
2) Press joystick shortly to activate Auto focusing.
3) If no further action during 5sec, adjust focusing mode will be closed automatically.
※ To get fine focusing, video will be zoomed twice in Adjust Focusing mode.
3. Shutter mode setup based on installation environment
Choose shutter mode based on installation environment as follows to minimize motion
blur of a moving object.
- Auto : This mode can maximize sensitivity under low light condition, but if the target
object is moving fast, motion blur could appear. You can use DSS, WDR
functions at this mode.
- Indoor : This mode can provide more clear moving image such as person in indoor
environment.
- Outdoor : This mode can provide more clear moving image such as vehicle in
outdoor environment.
* Under Indoor/Outdoor mode, DSS, WDR functions cannot be used and low-light
performance will be decreased. If you do not consider the environmental condition of
the installation site, malfunction of exposure might appear.
4. DC12V or AC24V(500mA over) power adapter must be used.
5. Please contact to qualified service personnel in case of product damage. Do not
attempt to repair product by yourself.
6. Please avoid external shock and vibration on the product.
7. Do not install product under excessive heat or cold environment. (recommended
operation temperature is 0°C~50°C)
8. Do not target lens to the sun. Image sensor might be damaged
9. Do not open the product under any circumstances, it could void the warranty. Natural
disaster like lightning, flood will need charge for repair.
1
English
Caution for installation and usage
Feature
HD-SDI video digital signal
HD-SDI(High Definition Serial Digital Interface) is non-compressed digital signal for
broadcasting, and there is no quality loss of high definition images.
2MP, Full HD high resolution picture quality
Full HD(1920x1080) provides 6 times higher resolution than SD level camera, and more
clear video image can be achieved through 1/3”, 2Megapixel progressive CMOS.
High performance under low light environment
High performance quality can be achieved under low light environment by optimizing the
image handling technology on CMOS sensor.
(B/W : 0.0005 Lux / Color : 0.2Lux@50IRE, F.1.4, 3100K, DSS OFF)
Indoor/Outdoor function
Indoor mode provides clear image by minimizing Motion Blur from slow moving person
indoors, and outdoor mode provides clear images for fast moving vehicles outdoors by
optimizing video signal handling according to each environment.
3D-DNR
3D-DNR function efficiently removes video noise in dark environment, and shows clear
image as a result.
True Day & Night function
Camera senses the surrounding brightness automatically, and insert/remove the IR-CUT
filter to get the best sensitivity performance.
WDR/BLC/ACE/HLC
Under backlight condition, you can select the most suitable function among WDR, BLC,
ACE and HLC.
Auto Focusing function
provides simple one-click auto focus function for easy installation.
Privacy support
Camera can support up to 28 privacy masking areas.
OSD control and F/W upgrade
OSD control and Firmware upgrade of camera can be achieved from PC or Webgate DVR
through RS485 communication.
2
Supplied accessories
Please check if all the supplied accessories are included.
Camera
Installation / User Manual
Monitoring Cable(IR18)
Hood Screw
Iron Screw
L Wrench
C1080BL-IR48-AF Hood
C1080BL-IR18-AF Hood
Product description
No
Name
1
Camera
2
Camera Hood
3
RS485 Port
4
Power input connector
5
Video output BNC connector
Camera installation
Auto Iris connector wiring
We recommend to use ‘Adjust Focusing’ mode for camera focusing.
1) Move Tele, Wide to adjust Zoom and Near, Far to adjust Focus.
2) Press joystick shortly to activate Auto focusing.
3) If no further action during 5sec, Adjust Focusing mode will be closed automatically.
3
※ To get fine focusing, video will be zoomed twice in Adjust Focusing mode.
Notice for Auto Focus operation
Following conditions might make failure of auto focusing .
1. When there are changes of the scene while Auto Focus is working(sudden movement,
appearance or disappearance).
2. When there are sudden change of the brightness.
3. When shooting low contrast image.
4. When there is strong light in the scene.
5. When there is foreign substance on the lens.
6. If auto focusing is failed, please try to adjust focus manually or try auto focus again
with the scene which have strong contrast.
Monitor connection
1. Use coaxial cable to connect camera with monitor.
2. Monitor needs to support SDI.
3. If monitor does not have SDI input connector, you may use additional SDI to HDMI
converter.
Cautions when you connect BNC cable
The impedance of BNC connector should be 75Ω.
If 50Ω connector is used, the transmission distance will be reduced approx. 10m.
Caution in cable selection
The maximum transmission distance of HD-SDI will vary depending on cable manufacturer
and installation environment. Please refer to the below table to select suitable coaxial cable.
Cable type
Transmission distance
Purpose
2V
about 100M
For analog signal
4C-FB(T), 4C-HFB(T), RG59
about 150M
High-foamed, double or triple
shielded cable is recommended
5C-FB(T), 5C-HFB(T), L-6CHD,
RG6
about 200M
Dedicated cable for HD-SDI
Power connection
Adapter should be DC12V or AC24V. But in case use DC power,
Please be careful in the polarity when connect power.
OSD control and Firmware upgrade using RS485 communication
1. Connect Webgate’s HD-SDI DVR with camera through RS485.
4
2. Configure PTZ settings such as Protocol(C1080), Baudrate, Address in DVR.
3. Run HD Camera Upgrade program then enter IP address of DVR which is connected to
camera and enter channel number of camera.
- PC for Firmware upgrade and DVR need to be connected with network.
- HD Camera Upgrade program and firmware can be downloaded from Webgate’s
website.
4. Select a Firmware and click Load button. Then firmware upgrade will proceed and the
camera will reboot automatically after completion.
- Image will stop until boot completes.
- If image stops over 1min, select Aux1 of selected channel to reboot camera again.
5. After firmware upgrade, DVR or CMS(Control Center) can change camera configuration
by controlling camera’s OSD menu remotely.
How to use OSD menu
OSD menu function
If pressing MENU button over 1 sec continuously, OSD menu will be shown.
- If OSD menu is not closed, it will be closed automatically in 1 minute. (Changed
configuration value will not be saved)
- Bold font with underline means factory default.
OSD MENU
ADJUST
FOCUSING
LENS
Function
If pressing Menu button less than 1 sec, Adjust Focusing mode will be
activated.
- After Focus Adjustment, if you press the MENU button again, Adjust
Focusing mode will be closed.
- If you do not exit the menu, it will be closed automatically in 1 minute.
DC(AF Model)
This is DC Iris Auto Focus lens which can make a focus
either by automatically and manually.
- Autofocus : Autofocusing by joystick one-click.
- Zoom(AF) : Autofocusing after Tele, Wide action.
- Manual : Move joystick to up(Tele), down(Wide),
left(Near),right(Far) to adjust angle and
focus manually.
5
- D&N AF : Autofocusing after Day&Night chages
DAY
Color
Maintains Color(Day) mode regardless brightness.
&
NIGHT
B&W
Maintains B&W(Night) mode regardless brightness.
Auto
In accordance with brightness, camera switches Color
mode and B&W mode automatically.
- LUX LEVEL(LOW, MIDDLE, HIGH) : This value is the
standard for Day & Night switching. If high is
selected, camera will turn to Night(B/W) mode at
higher LUX level than MIDDLE or LOW.
- ANTI HUNT(LOW, MIDDLE, HIGH) : This value is the
standard for threshold of Day & Night switching.
Higher setting value will reduce the flickering by
IR-CUT filter switching caused from misjudgment.
- DELAY TIME(3~30sec) : Judgment period for Day &
Night switching
EXPOSURE
BRIGHTNESS
(8, 0~20)
Adjust the brightness of image.
The more High value it has, the more bright image it
shows
SHUTTER
AUTO : In accordance with the brightness, shutter
speed is automatically changed
MANUAL : User can change the shutter speed
manually between 1/30 and 1/60000.
INDOOR : Optimized to indoor environment.
OUTDOOR : Optimized to outdoor environment like
fast moving object like car running.
ANTI-FLICKER : Removes Flicker problem due to the
discordance of light frequency.
COLOR
DSS
(OFF, x2~x10)
At night time or very dark condition, it accumulates
the amount of light into the image pixels and provides
more clear video image. But the higher setting value
may make more severe motion blur accordingly.
AGC
(7, 1~10)
It will amplify video gain according to the light
condition, but it will also increase noise level.
AWB
- AUTO : This mode automatically adjusts color white
balance between 1,700°K ~ 11,000°K.
- PRESET : Shoot a white paper in front of camera and
press MENU button then white balance working will
stop suitable for the condition. You must do this
process again if light condition is changed.
- MANUAL : User can select color temperature among
3300°K, 4300°K, 7600°K and adjust the details by
6
KELVIN, R-GAIN and B-GAIN value.
CHROMA
Adjust Chroma level.
(10, 0~20)
IMAGE
SHARPNESS
(5, 0~10)
Adjust sharpness. The higher value will show more
clear video image
H-MIRROR
Mirror image. Left and right will be reversed
V-MIRROR
Flip image. Up and down will be reversed.
Digital ZOOM
Zoom image by 16 steps. (1~16)
PRIVACY
This is for privacy zone masking
- ZONE NO : Supports total 28 areas (0~27)
-
ZONE OP : Whether to use or not of selected area
X, Y-POS : Set the X,Y start position of an area
X, Y-SIZE : Set the width and height of an area
COLOR(WHT,YEL,CYN,GRN,MAG,RED,BLU,BLK) : Select
color for masking.
- TRANS(0~4) : Set transparency of masking.
WDR
BLC
SHADING
DET
Before execute the SHADING function, shoot a white
paper in front of the camera, and do SHADING DET. If
not, abnormal video might be output.
SHADING
It compensates the difference of light caused by lens.
To use this function, you should run Shading DET
function first at System menu.
This 3D backlight compensation function allows bright and dark area to
be seen clearly together.
- WDR WGT(0~4) : Select image mix ratio. The higher value, the bright
part of the image appear more clearly
Back light compensation function.
- BLC LEVEL(LOW, MIDDLE, HIGH) : Set BLC level.
- BLC OSD : Displays BLC area on the screen.
- BLC POS-X, Y : Set X, Y start position.
- BLC SIZ-X,Y : Set Width and Height size.
- MASK : If there is very bright portion inside BLC area, this portion can
be removed from the calculation of BLC compensation. This brightness
level for masking can be decided by below MASK LEVEL.
- MASK LEVEL(0~10) : Set brightness level for Masking.
HLC
High Light Compensation. If there is very bright portion inside a scene,
camera can mask the portion, and the portion is removed from the
calculation for exposure control.
- LEVEL(5, 0~10) : Set the brightness level for masking.
- Color : Set masking color
ACE
Adaptive Contrast Enhancement. Enhances image quality by raising the
7
(ON, OFF)
brightness of dark areas.
DNR
Reduce image noise under low light condition
(LOW, MIDDLE, HIGH)
FRAMERATE
(25Hz, 30Hz)
SYSTEM
Power frequency 60Hz(NTSC) : 30Hz(fps) video output
Power frequency 50Hz(PAL) : 25Hz(fps) video output
MODEL
Displays model name
CAM ID
Max. 8 digits for camera name.
Supports alphanumeric and some special characters
RS485 ID
Set ID for RS485
VERSION
Displays firmware version
RESOLUTION
Set output resolution (1080p/720p).
DIGITAL OUT
/
IR-LED
Provides control signal output for sub light which is
synchronized with image process.
- DURATION(0~20) : Set the one cycle duration of TTL
signal output (unit : msec)
- POLARITY : Set the output level of TTL signal.
(0 : 0V , 1 : 3.3V)
* Output cycle is decided by 30Hz/25Hz.
EXIT
BAUDRATE
(9600, 57000)
Set RS485 communication speed.
RESET
Makes all setting values to factory default condition
SAVE&EXIT
Save configuration and exit menu.
EXIT
Without saving configuration, exit menu.
If there is no further action in menu, after 1 minute,
OSD menu will exit without saving changes.
Product Specification
Model
C1080BL-IR48-AF / C1080BL-IR18-AF
Video
Sensor Type
1/3” 2.1Megapixel CMOS
Total Pixels
1920(H) x 1080(V) = 2.1M pixels
Scanning System
Progressive Scan
Min
B/W
0.0005Lux@50IRE, F1.2, 3100K, DSS(OFF), AGC(10)
Illumination
Color
0.2Lux@50IRE, F1.2, 3100K, DSS(OFF), AGC(10)
Lens
DC 3 ~ 10mm F1.3
type
DC Auto Iris
Output
1(BNC 1.0 Vp-p, 75Ω)
Resolution
1080p 30fps / 25fps
HD-SDI
SMPTE 292M compatible
Lens
Video Output
8
Video
Control
Distance
approx. 200m of RG6, 150m of RG59
Control Method
OSD(Internal Joystic), DVR, CMS(Control Center)
Filter
True Day & Night
AGC
1 ~ 10 steps
Mirror
Horizontal / Vertical
WDR
OFF, 0 ~ 4 setup
BLC
OFF, LOW, MIDDLE, HIGH
ACE
OFF, ON
DNR
OFF, LOW, MIDDLE, HIGH
DSS
OFF, x2 ~ x10
White Balance
AUTO, PRESET, MANUAL
Electric Shutter
AUTO, MANUAL(12 steps), INDOOR, OUTDOOR
ANTI-FLICKER
Digital Zoom
0 ~ 16 steps
Lens Shading
OFF, ON
HLC
0 ~ 10 steps
Privacy
OFF/ON (28 Zones )
Control Interface
RS485
Upgrade Firmware / OSD Control
Strobe for external light
TTL level(3.3v)
Electricity
Power
Consumption
C1080BL-IR18-AF
DC 12V ± 10%, 4W / AC 24V ± 10%, 6W
C1080BL-IR48-AF
DC 12V ± 10%, 5W / AC 24V ± 10%, 8W
C1080BL-IR18-AF
88(W) x 118(H) x 198(D) mm
C1080BL-IR48-AF
120(W) x 140(H) x 254(D) mm
C1080BL-IR18-AF
720g
C1080BL-IR48-AF
1600g
Mechanical
Dimension
Weight
Environments
Operation Temp. / Humidity
0 ºC ~ 50 ºC / 0%RH ~ 80%RH
Certifications
Certifications
KC, FCC, CE, RoHS
9
Dimension
(unit : mm)
C1080BL-IR18-AF
C1080BL-IR-48-AF
10
How to upgrade C1080 Series Camera through DVR
1. Check F/W version of DVR and Camera.
- Camera : Over v1.2.x (System
 Version info. v1.0.x doesn’t support remote upgrade)
- DVR : Over v3.9.30
- Control Center : Over v2.26.x
2. Connect Com2/Com3(RS-485) port of DVR with RS-485 of C1080 camera.
- GND need to be connected as well as + , - when connect RS-485.
- Use twist pair cable in case the distance between DVR and Camera is far(over 5m).
- Set (Termination) On , in case the distance between DVR and Camera is far (over 5m).
3. If the F/W of DVR is lower than v3.9.30, please update DVR F/W.
4. After upgrade DVR, Please set up Com2 or Com3 port and PTZ as follow.
Com 2 / Com 3
PTZ
Device
PTZ
Enable
Check(√)
Connection
Interface : RS-485
Port Dependency : COM2/COM3 RS485
Baudrate : 9600 / 57600
Address : 1~255
Data Bits : 8bits
Stop Bits : 1bits
Parity : None
PTZ
Device : C1080
<Note>
1) In case multi cameras in same Serial port will be upgrade, please assign different ID per each camera.
EX) C1080B x 3ea in same port
 RS485 ID is No.1 camera : 1 , No.2 camera : 2 , No.3 camrea : 3.
2) In case multi cameras are updated in same serial port, upgrade will halt when power of camera in same serial line
reboot.
5. Please run “HD_Camera_Upgrader” and follow below steps.
1)
Run the HD_Cam_Upgrade then select camera F/W to upgrade.
2)
Enter IP address of DVR where to-be upgrade camera is connected then select channel and select upgrade file and click ‘Load’
button.
<Note>
1) User doesn’t need to enter port number even though connected DVR has specific port. Just enter IP address of DVR.
2) Select correct F/W per model. Otherwise camera might not show correct display.
- C1080B : C1080B_v1.xx.x.bin
- C1080BM : C1080BM_v1.xx.x.bin
- C1080D Series(D,VD,D-IR,VD-IR) : C1080VD_v1.xx.x.bin
- C1080AF Series(D-AF,D-IR-AF,VD-AF,VD-IR-AF,BL-IR18-AF,BL-IR48-AF) : C1080AF_v1.xx.x.bin
3) The upgrade time via Network will be various based on environment and Baudrate.
- Baudrate 9600 : About 2min 20sec
- Baudrate 57600 : About 1min 30sec
3)
Once upgrade is done after click ‘Load’ button, it takes about 1min 20sec ~ 2min for upgrade.
In this case, camera display looks white as if it is over exposed but please be noted that this is not a bug.
But in case the display keeps halted after 2 min, please click on Load button in HD_Camera_Upgrader one more time to
proceed with upgrade.
6. Once camera upgrade is done and image looks normal after finishing step 5, then select upgraded
channel in single channel mode in Control Center Monitor.
Then click on right button of mouse to enter popup menu and go to “Camera Setup”.
7. Camera OSD menu is activated when click Camera Setup menu and there will be control window at the
right bottom side of the screen.
<Note>
1) The possible delay could be occurred during menu control based on network situation.
2) Make single channel in DVR then click PTZ button of DVR then it will be same as control in
C.C (Control Center).
3) ESC button is not used.
8. Please pay attention while F/W upgrade into the latest version and F/W upgrade with wrong F/W will
make camera work abnormally. Please refer to below classified table to check F/W version.
1) Directions for upgrade of camera
+ If the camera is upgraded with wrong F/W, camera will not be working normally.
+ C1080B/BM model can be upgraded with the latest F/W regardless of mechanical part and lens.
+ Please upgrade B type after checking lens.
+ Please be noted not to disconnect power and RS485 connection during upgrade
+ The image of camera will remain stop while it is being upgraded and it takes maximum 3 minutes
to complete upgrade.
+ Please try upgrade one more time once the camera is not working normally after 9 minutes from
the beginning of upgrade.
+ A type model without RS485(green, white) line in cable will not be supporting upgrade.
2) Upgrade classified table
+ By mechanical part = A type : OLD mechanical part, B type : NEW / by lens = a type : OLD, b type :
NEW
Classification
A type
By
mechanical
part
F/W
Non AF Series : C1080BM_v1.13.0
AF Series : C1080AF_v1.13.0b
B type
Classification
By
mechanical
part
F/W
Classification
Non AF Series : C1080VD_v1.14.0
a type
b type
By lens
F/W
AF Series
C1080AF_v1.13.0a
Upgrade not required