Whirlpool GY399LXUB02 Product specifications

MC-1
TECHNICAL EDUCATION
FAILURE CODES AND
WIRING DIAGRAMS
for
MAYTAG HERITAGE
GAS & ELECTRIC RANGES
JOB AID 8178713
FORWARD
This Maytag Heritage Job Aid, “Failure Codes And Wiring Diagrams For Gas & Electric Ranges,”
(Part No. 8178713), provides the technician with information on Diagnosing and Troubleshooting Maytag Heritage Gas & Electric Ranges. It is to be used as a training Job Aid. For specific
information on the model being serviced, refer to the “Use and Care Guide,” or “Tech Sheet”
provided with the unit.
The Wiring Diagrams used in this Job Aid are typical and should be used for training purposes
only. Always use the Wiring Diagram supplied with the product when servicing the unit.
GOALS AND OBJECTIVES
The goal of this Job Aid is to provide detailed information that will enable the In-Home Service
Professionals to properly diagnose malfunctions and repair Maytag Heritage Ranges.
The objectives of this Job Aid are to:
• Successfully troubleshoot and diagnose malfunctions.
• Offer Electronic Oven Control information.
WHIRLPOOL CORPORATION assumes no responsibility for any repairs made
on our products by anyone other than In-Home Service Professionals.
Copyright © 2008, Whirlpool Corporation, Benton Harbor, MI 49022
- ii -
TABLE OF CONTENTS
Page
GENERAL ............................................................................................................................... 1-1
Gas & Electric Range Safety.............................................................................................. 1-1
Cooking Nomenclature....................................................................................................... 1-2
Model & Serial Number Label And Wiring Diagram Locations............................................ 1-3
Description of Error Codes.................................................................................................... 2-1
NSC (Non-Self Cleaning) Controls........................................................................................ 3-1
H1 Controls............................................................................................................................. 4-1
H2 Controls............................................................................................................................. 5-1
H2.5 Controls.......................................................................................................................... 6-1
H3 Controls............................................................................................................................. 7-1
M1/M2 Controls....................................................................................................................... 8-1
EOC III Controls...................................................................................................................... 9-1
UH Controls........................................................................................................................... 10-1
- iii -
Family
Control Part #
Model #
Application
Tech Sheet
Page #
H2.5
8507P328-60
629.600
6-2
H2.5
8507P328-60
629.600
6-2
H2.5
8507P328-60
629.600
6-2
H2.5
8507P328-60
629.600
6-2
NSC
8507P347-60
AER4311AAW
Electric F/S Range
16026465
3-4
NSC
8507P348-60
AER4311ACW
Electric F/S Range
16026465
3-4
M1
8507P304-60
AER5511AAW
Electric F/S Range
16023530
8-4
M1
8507P304-60
AER5511ACW
Electric F/S Range
16023539
8-4
M1
8507P304-60
AER5511BAW
Electric F/S Range
16026686
8-4
M1
8507P304-60
AER5512AAW
Electric F/S Range
16023530
8-4
M1
8507P252-60
AER5515QAW
Electric F/S Range
16025645
8-7
M1
8507P252-60
AER5515QCW
Electric F/S Range
16026853
8-14
M1
8507P252-60
AER5515RCW
Electric F/S Range
16027236
8-17
M1
8507P304-60
AER5710BAH
Electric F/S Range
16026813
8-4
M1
8507P304-60
AER5712AAW
Electric F/S Range
16023531
8-4
M1
8507P304-60
AER5712ACW
Electric F/S Range
16023542
8-4
M1
8507P304-60
AER5712BAW
Electric F/S Range
16026688
8-4
M1
8507P252-60
AER5715QAW
Electric F/S Range
16025646
8-7
M1
8507P252-60
AER5715QCW
Electric F/S Range
16023319
8-3
M1
8507P252-60
AER5715RCW
Electric F/S Range
16027231
8-17
M1
8507P304-60
AER5722BAW
Electric F/S Range
16026691
8-4
M1
8507P304-60
AER5722CAS
Electric F/S Range
16027074
8-4
M1
8507P252-60
AER5725QAW
Electric F/S Range
16027227
8-17
M2
8507P253-60
AER5735QAW
Electric F/S Range
16025648
8-7
H1
8507P293-60
AER5815RCW
Electric F/S Range
16027233
4-22
H1
8507P356-60
AER5845QAB
Electric F/S Range
16022492
4-15
H1
8507P356-60
AER5845RAW
Electric F/S Range
16027232
4-21
M1
8507P239-60
AES1350BAW
Electric Slide-In Range
16026294
8-10
M2
8507P260-60
AES3760BAW
Electric F/S Range
16026295
8-11
H1
8507P260-60
AES3760BCW
Electric F/S Range
16026298
4-16
H1
8507P305-60
AES5730BAB
Electric Slide-In Range
16026296
4-16
H1
8507P286-60
AEW3530DDW
Electric Wall Oven
16022507
4-9
H2.5
8507P325-60
AEW3630DDW
Electric Wall Oven
16022511
5-5
H1
8507P287-60
AEW4530DDW
Electric Wall Oven
16022507
4-9
H2.5
8507P326-60
AEW4630DDW
Electric Wall Oven
16022511
5-5
NSC
8507P348-60
AGR4412ADW
Gas F/S Range
16026763
3-7
M1
8507P250-60
AGR5712ADW
Gas F/S Range
16023524
8-6
M1
8507P250-60
AGR5712BDW
Gas F/S Range
16026684
8-6
- iv -
Family
Control Part #
Model #
Application
Tech Sheet
Page #
M1
8507P254-60
AGR5715QDW
Gas F/S Range
16027222
8-16
M2
8507P255-60
AGR5725QDW
Gas F/S Range
16022500
8-5
M1
8507P254-60
AGR5725RDW
Gas F/S Range
16026797
8-13
M1
8507P254-60
AGR5725SDS
Gas F/S Range
16027246
8-16
M2
8507P255-60
AGR5735QDW
Gas F/S Range
16022500
8-5
H1
8507P292-60
AGR5825RDW
Gas F/S Range
16026851
4-18
H1
8507P292-60
AGR5835QDW
Gas F/S Range
16022501
4-8
M1
8507P259-60
AGS1740BDW
Gas Slide-In Range
16026289
8-8
M2
8507P261-60
AGS3760BDW
Gas Slide-In Range
16026290
8-9
H1
8507P306-60
AGS5730BDW
Gas Slide-In Range
16026291
4-11
M1
8507P254-60
ALR5715QDW
Gas F/S Range LP
16027225
8-18
NSC
8507P347-60
CE35400AAV
Electric F/S Range
16026465
3-4
NSC
8507P347-60
CE35400ACV
Electric F/S Range
16023535
3-4
M1
8507P304-60
CE38600AAW
Electric F/S Range
16023530
8-4
M1
8507P304-60
CE38600ACV
Electric F/S Range
16023539
8-4
M1
8507P304-60
CE38800AAW
Electric F/S Range
16023534
8-4
M1
8507P304-60
CE38800ACS
Electric F/S Range
16023481
8-4
M1
8507P304-60
CE38800BAS
Electric F/S Range
16026978
8-4
NSC
8507P347-60
CER1125AAW
Electric F/S Range
16026465
3-4
NSC
8507P347-60
CER1125ACW
Electric F/S Range
16023535
3-5
M1
8507P304-60
CER3525AAW
Electric F/S Range
16023530
8-4
M1
8507P304-60
CER3525ACW
Electric F/S Range
16023539
8-4
M1
8507P304-60
CER3725AAW
Electric F/S Range
16023531
8-4
M1
8507P304-60
CER3725ACW
Electric F/S Range
16023542
8-4
NSC
8507P349-60
CER3725AGW
Electric F/S Range
16026838
3-8
NSC
8507P349-60
CER4351AGW
Electric F/S Range
16026300
3-6
M1
8507P240-60
CES3759BCW
Electric Slide-In Range
16027221
8-15
NSC
8507P348-60
CG31600ADV
Gas F/S Range
16026763
3-7
M1
8507P250-60
CG34800ADW
Gas F/S Range
16023524
8-6
M1
8507P250-60
CG34800BDS
Gas F/S Range
16026791
8-12
NSC
8507P348-60
CGR1425ADW
Gas F/S Range
16026763
3-7
M1
8507P250-60
CGR3725ADW
Gas F/S Range
16023524
8-6
M1
8507P250-60
CGR3726ADW
Gas F/S Range
16026551
8-6
NSC
8507P348-60
CP31600ADV
Gas F/S Range
16026763
3-7
H1
8507P389-60
GW397LXUB
Gas Slide-In Range
H1
8507P391-60
GW399LXUB
Gas Slide-In Range
16026291
4-15
H1
8507P390-60
GY397LXUB
Electric Slide-In Range
H1
8507P392-60
GY399LXUB
Electric Slide-In Range
16026296
4-16
-v-
Family
Control Part #
Model #
Application
Tech Sheet
Page #
H2.5
8507P302-60
JDR8895AAW
Double Oven Dual Fuel
16023460
6-8
H2.5
8507P302-60
JDR8895ACW
Double Oven Dual Fuel
16023460
6-8
EOCIII
8507P333-60
JDR8895RDW
Double Oven Dual Fuel
16023506
EOCIII
8507P230-60
JDS8850BDW
Dual Fuel Slide-In
16026930
9-15
EOCIII
8507P231-60
JDS9860BDW
Dual Fuel Slide-In
16026930
9-15
EOCIII
8507P380-60
JDS9860AAW
Dual Fuel Slide-In
16026780
9-15
EOCIII
8507P232-60
JDS9865BDP
Dual Fuel Slide-In
16026930
9-15
EOCIII
8507P278-60
JER8785QAB
Electric F/S Range
16027223
4-19
EOCIII
8507P331-60
JER8785RAB
Electric F/S Range
16027306
9-17
H1
8507P279-60
JER8885QAB
Electric F/S Range
16027226
9-19
H1
8507P279-60
JER8885QCB
Electric F/S Range
16027224
4-14
U3
8507P386-60
JER8885RAB
Electric F/S Range
16027307
9-18
EOCIII
8507P331-60
JER8885RCW
Electric F/S Range
16027308
9-14
EOCIII
8507P225-60
JES8750BAW
Electric Slide-In
16026927
9-14
EOCIII
8507P226-60
JES8850BAB
Electric Slide-In
16026927
9-15
EOCIII
8507P226-60
JES8850BCW
Electric Slide-In
16027013
9-15
EOCIII
8507P233-60
JES9750BAW
Electric Slide-In
16026928
9-15
EOCIII
8507P234-60
JES9800BAB
Electric D/D Slide-In
16027004
9-15
EOCIII
8507P234-60
JES9860BAW
Electric Slide-In
16026928
9-15
EOCIII
8507P234-60
JES9900BAB
Electric D/D Slide-In
16027004
9-15
EOCIII
8507P234-60
JES9900BCW
Electric Slide-In
16027013
9-15
H1
8507P289-60
JGR8775QDW
Gas F/S Range
16022502
4-8
EOCIII
8507P351-60
JGR8775RDW
Gas Freestanding Range
16027309
9-19
H1
8507P290-60
JGR8875QDW
Gas F/S Range
16022503
4-10
EOCIII
8507P351-60
JGR8875RDW
Gas Freestanding Range
16027310
9-20
EOCIII
8507P351-60
JGR8885RDP
Gas Freestanding Range
16027248
9-16
EOCIII
8507P227-60
JGS8750BDW
Gas Slide-In
16026924
9-13
EOCIII
8507P228-60
JGS8850BDW
Gas Slide-In
16026924
9-13
EOCIII
8507P229-60
JGS8860BDP
Gas Slide-In
16026924
9-13
EOCIII
8507P236-60
JGS9900BDB
Gas Slide-In
16026925
9-13
H1
8507P085-60
JGW8130DDW
Gas Wall Oven
16022515
4-13
H1
8507P090-60
JJW7530DDW
Electric Wall Oven
16022508
4-12
H1
8507P285-60
JJW8130DDW
Electric Wall Oven
16022507
4-9
H2.5
8507P324-60
JJW8230DDW
Electric Wall Oven
16022511
5-5
M1
8507P345-60
JJW8527DDW
Electric Wall Oven
16026101
8-6
M1
8507P263-60
JJW8530DDW
Electric Wall Oven
16026101
8-6
UH
8507P364-60
JJW8627DDW
Electric Wall Oven
16022512
10-4
UH
8507P364-60
JJW8630DDW
Electric Wall Oven
16022512
10-4
H1
8507P291-60
JJW9130DDW
Electric Wall Oven
16026545
4-9
H2.5
8507P327-60
JJW9230DDW
Electric Wall Oven
16026546
5-5
- vi -
Family
Control Part #
Model #
Application
Tech Sheet
Page #
H1
8507P291-60
JJW9330DDB
Electric Wall Oven
16026545
4-9
H2.5
8507P360-60
JJW9430DDB
Electric Wall Oven
16026546
5-5
UH
8507P264-60
JJW9527DDW
Electric Wall Oven
16026101
10-5
UH
8507P338-60
JJW9530DDP
Electric Wall Oven
16026100
10-8
UH
8507P264-60
JJW9530DDW
Electric Wall Oven
16026101
10-5
UH
8507P363-60
JJW9627DDW
Electric Wall Oven
16022512
10-4
UH
8507P363-60
JJW9630DDW
Electric Wall Oven
16022512
10-4
UH
8507P361-60
JJW9827DDP
Electric Wall Oven
16026100
10-8
UH
8507P342-60
JJW9827DDW
Electric Wall Oven
16022512
10-4
UH
8507P361-60
JJW9830DDP
Electric Wall Oven
16026100
10-8
UH
8507P362-60
JJW9830DDW
Electric Wall Oven
16022512
10-4
H1
8507P285-60
JMW8130DAW
Electric Wall Oven w/MW
16026568
4-17
H1
8507P285-60
JMW8330DAW
Electric Wall Oven w/MW
16026568
4-17
UH
8507P263-60
JMW8527DAW
Electric Wall Oven w/MW
16022823
10-5
UH
8507P263-60
JMW8530DAW
Electric Wall Oven w/MW
16022823
10-5
UH
8507P345-60
JMW8530DAW
Elec. Wall Oven w/MW
16022823
10-5
H1
8507P291-60
JMW9130DAW
Electric Wall Oven w/MW
16026569
4-17
H1
8507P291-60
JMW9330DAW
Electric Wall Oven w/MW
16026569
4-17
UH
8507P264-60
JMW9527DAW
Electric Wall Oven w/MW
16022823
10-5
UH
8507P346-60
JMW9527DAW
Elec. Wall Oven w/MW
16022823
10-5
UH
8507P264-60
JMW9530DAW
Electric Wall Oven w/MW
16022823
10-5
UH
8507P346-60
JMW9530DAW
Elec. Wall Oven w/MW
16022823
10-5
M1
8507P304-60
LER3330AAW
Electric F/S Range
16026105
8-4
M1
8507P250-60
LGR3330ADW
Gas F/S Range
16026106
8-12
NSC
8507P350-60
LLR4451AJW
Gas F/S Range
16026765
3-7
H1
8507P299-60
MEP5775BAB
Electric Slide-In Range
16026297
4-16
NSC
8507P347-60
MER4351AAW
Electric F/S Range
16026465
3-4
NSC
8507P347-60
MER4351ACW
Electric F/S Range
16026465
3-4
NSC
8507P349-60
MER4351AGW
Electric F/S Range
16026535
3-5
M1
8507P304-60
MER5520AAW
Electric F/S Range
16026686
8-4
M1
8507P304-60
MER5551AAW
Electric F/S Range
16023530
8-4
M1
8507P304-60
MER5551BAW
Electric F/S Range
16026686
8-4
M1
8507P304-60
MER5552AAW
Electric F/S Range
16023530
8-4
M1
8507P249-60
MER5552ACW
Electric F/S Range
16023530
8-4
M1
8507P304-60
MER5552BAW
Electric F/S Range
16026686
8-4
M1
8507P252-60
MER5555QAW
Electric F/S Range
16025645
8-7
M1
8507P252-60
MER5555QCW
Electric F/S Range
16023318
8-3
M1
8507P252-60
MER5555RCW
Electric F/S Range
16027237
8-17
M1
8507P304-60
MER5751AAW
Electric F/S Range
16023531
8-4
M1
8507P304-60
MER5751ACW
Electric F/S Range
16026543
8-4
- vii -
Family
Control Part #
Model #
Application
Tech Sheet
Page #
M1
8507P304-60
MER5751BAB
Electric F/S Range
16026688
8-4
M1
8507P304-60
MER5752AAW
Electric F/S Range
16023531
8-4
M1
8507P304-60
MER5752ACW
Electric F/S Range
16023542
8-4
M1
8507P304-60
MER5752BAW
Electric F/S Range
16026688
8-4
M1
8507P252-60
MER5754QAW
Electric F/S Range
16025646
8-7
M1
8507P252-60
MER5755QAW
Electric F/S Range
16025646
8-7
M1
8507P252-60
MER5755QCW
Electric F/S Range
16023319
8-3
M1
8507P252-60
MER5765QAW
Electric F/S Range
16025649
8-7
M1
8507P252-60
MER5765RAW
Electric F/S Range
16027247
8-17
M1
8507P252-60
MER5765RCW
Electric F/S Range
16027231
8-17
M2
8507P253-60
MER5775QAW
Electric F/S Range
16025648
8-7
M2
8507P253-60
MER5775QCW
Electric F/S Range
16023320
8-3
M2
8507P253-60
MER5775RAW
Electric F/S Range
16027230
8-17
M2
8507P253-60
MER5775RCB
Electric F/S Range
16027245
8-17
H1
8507P277-60
MER5875QAB
Electric F/S Range
16022496
4-19
H1
8507P069-60
MER5875QCW
Electric F/S Range
16023321
4-14
H1
8507P355-60
MER5875RAB
Electric F/S Range
16027229
4-20
H1
8507P355-60
MER5875RCW
Electric F/S Range
16027233
4-22
M1
8507P307-60
MER6541BAW
Double Oven Electric Range
16027255
8-19
H3
8507P272-60
MER6555AAW
Double Oven Electric Range
16023459
7-9
H3
8507P272-60
MER6555ACW
Double Oven Electric Range
16023459
7-9
M1
8507P307-60
MER6741BAW
Double Oven Electric Range
16027255
8-19
H3
8507P272-60
MER6751AAW
Double Oven Electric Range
16023459
7-9
M1
8507P307-60
MER6752BAW
Double Oven Electric Range
16027255
8-19
H3
8507P272-60
MER6755AAW
Double Oven Electric Range
16023459
7-9
H3
8507P272-60
MER6755ACW
Double Oven Electric Range
16023459
7-9
H3
8507P272-60
MER6765BAW
Double Oven Electric Range
16027359
7-9
H3
8507P272-60
MER6775AAW
Double Oven Electric Range
16023459
7-9
H3
8507P272-60
MER6775ACB
Double Oven Electric Range
16026151
7-9
H3
8507P272-60
MER6775BAB
Double Oven Electric Range
16027360
7-9
H3
8507P272-60
MER6775BCW
Double Oven Electric Range
16027360
7-9
H2.5
8507P203-60
MER6875AAW
Double Oven Electric Range
16026150
6-9
H2.5
8507P301-60
MER6875AAW
Double Oven Electric Range
16026150
6-9
H2.5
8507P203-60
MER6875ACW
Double Oven Electric Range
16026150
6-9
H2.5
8507P301-60
MER6875ACW
Double Oven Electric Range
16026150
6-9
M1
8507P304-60
MERB750BAW
M1
8507P304-60
MERH752BAW
Electric F/S Range
16026688
8-4
M1
8507P304-60
MERH752CAS
Electric F/S Range
16027144
8-4
H1
8507P357-60
MERH865RAW
M1
8507P304-60
MERL752BAW
Electric F/S Range
16026689
8-4
M1
8507P304-60
MERL753BAS
M1
8507P304-60
MERM752BAW
Electric F/S Range
16026688
8-4
- viii -
Family
Control Part #
Model #
Application
Tech Sheet
Page #
M1
8507P304-60
MERS751BAW
Electric F/S Range
16027075
8-4
M1
8507P252-60
MERS755RAW
Electric F/S Range
16027247
8-17
H1
8507P237-60
MES5775BAB
Electric Slide-In Range
16026297
4-16
H1
8507P237-60
MES5775BCW
Electric Slide-In Range
16026298
4-16
H1
8507P276-60
MES5875BAB
Electric Slide-In Range
16026297
4-16
H1
8507P276-60
MES5875BCB
Electric Slide-In Range
16026298
4-16
H1
8507P280-60
MEW5527DDW
Electric Wall Oven
16022507
4-9
H1
8507P281-60
MEW5530DDW
Electric Wall Oven
16022507
4-9
H2.5
8507P320-60
MEW5627DDW
Electric Wall Oven
16022511
4-9
H1
8507P086-60
MEW5627DDW
Electric Wall Oven
16022511
5-5
H2.5
8507P321-60
MEW5630DDW
Electric Wall Oven
16022511
5-5
H1
8507P087-60
MEW5630DDW
Electric Wall Oven
16022511
5-5
H1
8507P282-60
MEW6527DDW
Electric Wall Oven
16022507
4-9
H1
8507P283-60
MEW6530DDW
Electric Wall Oven
16022507
4-9
H2.5
8507P088-60
MEW6627DDW
Electric Wall Oven
16022511
5-5
H2.5
8507P089-60
MEW6630DDW
Electric Wall Oven
16022511
5-5
NSC
8507P348-60
MGR4451ADW
Gas F/S Range
16026763
3-7
NSC
8507P250-60
MGR4451BDS
Gas F/S Range
16026685
3-7
NSC
8507P348-60
MGR4451BDW
Gas F/S Range
16026685
3-7
NSC
8507P348-60
MGR4452ADW
Gas F/S Range
16026763
3-7
NSC
8507P348-60
MGR4452BDW
Gas F/S Range
16026685
3-7
M1
8507P250-60
MGR5751ADW
Gas F/S Range
16023524
8-6
M1
8507P250-60
MGR5751BDW
Gas F/S Range
16026683
8-6
M1
8507P250-60
MGR5752ADW
Gas F/S Range
16023524
8-6
M1
8507P250-60
MGR5752BDW
Gas F/S Range
16023524
8-6
M1
8507P254-60
MGR5754QDW
Gas F/S Range
16027222
8-16
M1
8507P254-60
MGR5755QDW
Gas F/S Range
16027222
8-16
M1
8507P254-60
MGR5765QDW
Gas F/S Range
16027222
8-16
M2
8507P255-60
MGR5775QDW
Gas F/S Range
16022504
8-5
H1
8507P288-60
MGR5875QDW
Gas Freestanding Range
16022505
4-11
H3
8507P262-60
MGR6751BDW
Double Oven Gas Range
16027362
7-8
H3
8507P262-60
MGR6775ADW
Double Oven Gas Range
16023458
7-8
H3
8507P262-60
MGR6775BDW
Double Oven Gas Range
16027363
7-10
H2.5
8507P204-60
MGR6875ADW
Double Oven Gas Range
16027364
6-10
H2.5
8507P300-60
MGR6875ADW
Double Oven Gas Range
16027364
6-10
M1
8507P250-60
MGRH752BDW
Gas F/S Range
16026684
8-6
H1
8507P358-60
MGRH865QDW
Gas F/S Range
M1
8507P250-60
MGRL752BDW
Gas F/S Range
16026684
8-6
M1
8507P250-60
MGRL753BDS
Gas F/S Range
16026684
8-6
M1
8507P250-60
MGRM752BDW
Gas F/S Range
16026683
8-6
M1
8507P250-60
MGRS752BDW
Gas F/S Range
16026683
8-6
- ix -
Family
Control Part #
Model #
Application
Tech Sheet
Page #
M1
8507P258-60
MGS5752BDW
Gas F/S Range
16026290
8-9
H1
8507P256-60
MGS5775BDW
Gas Slide-In Range
16026292
4-15
H1
8507P275-60
MGS5875BDW
Gas Slide-In Range
16026292
4-15
NSC
8507P350-60
MLR4451AJQ
Gas F/S Range
16026765
3-7
NSC
8507P350-60
MLR4451AJS
Gas F/S Range
16026765
3-7
NSC
8507P350-60
MLR4451AJW
Gas F/S Range
16026765
3-7
M1
8507P254-60
MLR5755QDW
Gas F/S Range
16027225
8-18
H1
8507P281-60
MMW5530DAW
Electric Wall Oven w/MW
16026275
4-17
NSC
8507P347-60
PER1125ACW
Electric F/S Range
16026486
3-5
M1
8507P304-60
PER3524ACW
Electric F/S Range
16026485
8-4
M1
8507P304-60
PER3525ACW
Electric F/S Range
16026485
8-4
M1
8507P304-60
PER3724ACW
Electric F/S Range
16026484
8-4
M1
8507P304-60
PER3725ACW
Electric F/S Range
16026484
8-4
NSC
8507P347-60
PER4311ACW
Electric F/S Range
16023535
3-5
M1
8507P304-60
PER5720ACW
Electric F/S Range
16023481
8-4
M1
8507P304-60
PER5720LAW
Electric F/S Range
16023534
8-4
M1
8507P252-60
PER5750QAW
Electric F/S Range
16025650
8-7
M1
8507P252-60
PER5750QCW
Electric F/S Range
16023323
8-3
M1
8507P304-60
PERL252AAW
M1
8507P304-60
PERL451AAB
M1
8507P304-60
PERL451ACW
Electric F/S Range
16026687
M1
8507P258-60
PGS3759BDW
Gas Slide-In Range
16026792
8-12
NSC
8507P348-60
PGR4420LDW
Gas F/S Range
16026763
3-7
M1
8507P250-60
PGR5720LDW
Gas F/S Range
16023524
8-6
M1
8507P254-60
PGR5750LDW
Gas F/S Range
16023524
8-6
NSC
8507P247-60
PGRL251ADW
M1
8507P250-60
PGRL451ADB
M1
8507P304-60
RESF3330DW
M1
8507P304-60
RESF5330DT
M1
8507P250-60
RGSF3330DW
M1
8507P250-60
RGSF5330DT
UH
8507P211-60
RJDO2702A
Electric Wall Oven
16025885
10-7
UH
8507P210-60
RJDO2703A
Electric Wall Oven
16025885
10-7
UH
8507P211-60
RJDO3002A
Electric Wall Oven
16025885
10-7
UH
8507P210-60
RJDO3003A
Electric Wall Oven
16025885
10-7
UH
8507P209-60
RJSO2701A
Electric Wall Oven
16025884
10-6
UH
8507P209-60
RJSO3001A
Electric Wall Oven
16025884
10-6
M1
8507P240-60
RS160LXTB
Electric Slide-In Range
16026294
8-10
M1
8507P240-60
RY160LXTB
Electric Slide-In Range
16026294
8-10
-x-
GENERAL
GAS & ELECTRIC RANGE SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on the appliance.
Always read and obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These words mean:
DANGER
You can be killed or seriously injured if you don’t
immediately follow instructions.
WARNING
You can be killed or seriously injured if you don’t
follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance
of injury, and tell you what can happen if the instructions are not followed.
1-1
Cooking Nomenclature
M
R
H
1
6
7
Amana
Magic Chef
Graffer &
Sattler
Hardwick
Jenn-Air
Maytag
Norge
Universal
Crosley
H
J
M
N
U
Y
B
D
E/J
G
L
M
P
X
W
B
D
A
B
C
H
L
P
Q
S
T
W
F
N
Brand
A
C
G
A
C
D
E
G
L
M
P
Q
R
S
T
V
W
Y
Z
E
Fuel
Color
Almond on Almond
Black
Brushed Chrome
Traditional White
Traditional Almond
Prostyle
Monochromatic Bisque
Stainless
Traditional Bisque
White on White
Frost White (True Color White)
Natural Bisque (True Color Bisque)
A
C
D
G
M
P
Butane
Dual Fuel
Electric
Gas, Natural
Liquid Propane
Microwave
Standing Pilot
No Fuel
Warming Drawer
W
X
Listing
UL/AGA
CSA/CGA/CUL
Dual Listed
220-240 V / 50-60 Hz
Military Model
PSB Approved
(Singapore)
Export 120 V / 60 Hz
Production Code
Product Type
Accessory/Cartridge
Cooktop Updraft/Countertop
Downdraft Cooktop or Warming Drawer
Eyelevel Range
Grill
Range (20")
Range (36")
Drop In (24")
National Accounts
Wall Oven (27")
Range, Free-Standing (30")
B = Best Buy
Slide-In (30")
H = Home Depot
Range Hood
S = Sears
OTR
Wall Oven
RV Range
RV Top
1-2
This identifies the
production version.
Feature Content
1000-3999
4000-6999
7000-9999
Brands
Maytag/Amana
Jenn Air
Serial Number Identification
There are three parts which Identifies the Serial Number.
• Series/Run Number – Indicates a specific product design.
− These two digits can be either alpha or numeric characters.
• Serial Identity – Identifies the number assigned to a product.
• Date Code – Indicates the month and year in which the product was built.
SERIAL NUMBER IDENTIFICATION
Series/Run
Number
XX
MODEL NO.
C236B
Serial
Identity
XXXXXX
SERIAL NO.
XXXXXXXXXX
XX
RATING
8.03
KW
120/240VAC
DO NOT CLEAN THIS LABEL
NOTE:
Date
Code
6.02
KW
120/208VAC
(60HZ 3 WIRE A.C. ONLY)
Some Amana Products are still identified by using a Manufacturing Number
(PXXXXXXXM).
All serial numbers consist of eight digits, followed by two letters.
The first letter indicates the year
in which the product was produced.
Year
2000
2001
2002
2003
2004
2005
2006
2007
2008
2009
2010
2011
2012
2013
The second letter indicates the month in
which the product was produced.
Code
Y
Z
A
C
E
G
J
L
N
P
R
T
V
X
Years Span
2002 − 2013
2002 − 2013
2002 − 2013
2002 − 2013
2002 − 2013
2002 − 2013
2002 − 2013
2002 − 2013
2002 − 2013
2002 − 2013
2002 − 2013
2002 − 2013
1-3
Month
January
February
March
April
May
June
July
August
September
October
November
December
Code
A
C
E
G
J
L
N
P
R
T
V
X
MODEL & SERIAL NUMBER LABEL
AND WIRING DIAGRAM LOCATIONS
The Model/Serial Number label and Wiring Diagram locations are shown below.
Wiring Diagram Location
(On Back Side Of Storage Drawer)
1-4
Model & Serial Number
Label Location
DESCRIPTION OF ERROR CODES
ERROR CODES
Description of Error Codes
Error diagnostic codes can only be viewed by entering the Diagnostic Code Display Mode.
Each error code is four digits long and is created based on the following table.
Digit
st
1
nd
2
rd
3
th
4
Description
1 – Local to the control circuit board
3 – Sensor or meat probe
4 – Control input
9 – Door lock
Measurable:
d – Diagnostic failure: measurable parameter
c – Control related error, replace control
Primary failure mechanism
Oven Cavity:
1 – Upper oven (or single cavity oven)
2 – Lower oven
c – Control specific
Primary System:
Diagnostic Code Checking
Code
Description
When Checked
Detection
1c1c
1c2c
1c31
1c32
1c4c
1c6c
1c7c
1c81
1c82
1d11
1d12
1d21
1d22
3d11
3d12
3d21
3d22
3d41
3d51
4d11
4d12
4d21
4d22
4d31
Always
Always
Always
Always
Always
W hen accessing EEPROM
Always
Cook or clean programmed
Cook or clean programmed
Latch unlocked
Latch unlocked
Latch locked
Latch locked
Cook or Clean active
Cook or Clean active
Cook or Clean active
Cook or Clean active
Probe cook programmed
Always
Clean or Keyboard Lockout active
Clean or Keyboard Lockout active
Cook or Clean programmed
Cook or Clean programmed
When supposed to be off
1 minute
1 minute
20 sec
20 sec
20 sec
3 tries
3 tries
3 tries
3 tries
1 minute
1 minute
1 minute
1 minute
20 sec
20 sec
20 sec
20 sec
20 sec
3 sec
1 minute
1 minute
1 minute
1 minute
1 minute
When supposed to be off
1 minute
4d41
4d42
4d51
Shorted key
Keyboard tail disconnected
Cancel key circuit problem
Cancel key circuit problem
Power micro communication failure
EEPROM error
Control not calibrated
Cook profile corrupted in EEPROM
Cook profile corrupted in EEPROM
Runaway temperature (650°F), door unlocked
Runaway temperature (650°F), door unlocked
Runaway temperature (950°F), door locked
Runaway temperature (950°F), door locked
Temperature sensor failure (open)
Temperature sensor failure (open)
Temperature sensor failure (short)
Temperature sensor failure (short)
Meat probe shorted
Meat probe not calibrated
Door switch position failure
Door switch position failure
No Reverse Airflow Fan rotation (no/low RPM)
No Reverse Airflow Fan rotation (no/low RPM)
Reverse Airflow Fan state error (on when supposed
to be off)
Reverse Airflow Fan state error (on when supposed
to be off)
High Reverse Airflow Fan rotation, high RPM
High Reverse Airflow Fan rotation, high RPM
Door switch circuit failure
1 minute
1 minute
1 minute
4d52
Door switch circuit failure
9d11
9d12
9d21
9d22
9d31
9d32
Latch will not lock 6
Latch will not lock 6
Latch will not unlock 6
Latch will not unlock 6
Latch both locked and unlocked 6
Latch both locked and unlocked 6
Cook or Clean programmed
Cook or Clean programmed
Convect, Clean, or Keyboard Lockout
programmed
Convect, Clean, or Keyboard Lockout
programmed
Latch should be locked
Latch should be locked
Latch should be unlocked
Latch should be unlocked
Latch should be locked or when lock attempted
Latch should be locked or when lock attempted
4d32
2-1
1 minute
See note 6
See note 6
See note 6
See note 6
See note 6
See note 6
Code
1c1c
Keypress
1c2c
Keyboard loop improper value
1c31
1c32
1c4c
1c6c
1c7c
1c81
1c82
1d11
1d12
1d21
1d22
3d11
3d12
3d21
3d22
3d41
3d51
4d11
4d51
Cancel key improper value
Cancel key improper value
CRC invalid
No response from EEPROM
Calibration value out of range
CRC invalid
CRC invalid
Sensor resistance >2237 Ω
Sensor resistance >2237 Ω
Sensor resistance >2787 Ω
Sensor resistance >2787 Ω
Sensor resistance > Infinite Ω
Sensor resistance > Infinite Ω
Sensor resistance < 0 Ω
Sensor resistance < 0 Ω
Probe resistance < 0 Ω
Calibration value out of range
Door switch not closed when
door is locked
Door switch not closed when
door is locked
Reverse Airflow Fan rotation
(no/low RPM)
Reverse Airflow Fan rotation
(no/low RPM)
Reverse Airflow Fan rotation
(on when should be off)
Reverse Airflow Fan rotation
(on when should be off)
Reverse Airflow Fan rotation
(high RPM)
Reverse Airflow Fan rotation
(high RPM)
Door switch not open or closed
4d52
Door switch not open or closed
mssg 1 (active) / mssg 2 (data)
9d11
9d12
9d21
9d22
9d31
9d32
Lock switch not closed
Lock switch not closed
Unlock switch not closed
Unlock switch not closed
Lock and unlock switches both closed
Lock and unlock switches both closed
mssg 1 (active) / mssg 2 (data)
mssg 1 (active) / mssg 2 (data)
mssg 1 (active) / mssg 2 (data)
mssg 1 (active) / mssg 2 (data)
mssg 1 (active) / mssg 2 (data)
mssg 1 (active) / mssg 2 (data)
4d12
4d21
4d22
4d31
4d32
4d41
4d42
Measured
Display
mssg 1 (active) / mssg 2 (data)
mssg 1 (active) / mssg 2 (data)
mssg 1 (active) / mssg 2 (data)
mssg 1 (active) / mssg 2 (data)
mssg 1 (active) / mssg 2 (data)
mssg 1 (active) / mssg 2 (data)
mssg 1 (active) / mssg 2 (data)
mssg 1 (active) / mssg 3 (data)
mssg 1 (active) / mssg 3 (data)
mssg 1 (active) / mssg 3 (data)
mssg 1 (active) / mssg 3 (data)
mssg 1 (active) / mssg 2 (data)
mssg 1 (active) / mssg 2 (data)
mssg 1 (active) / mssg 2 (data)
mssg 1 (active) / mssg 2 (data)
mssg 1 (active) / mssg 2 (data)
mssg 2
mssg 1
mssg 1
Action Taken
Disable audible for affected key depression,
Disable all outputs 1, 2
Disable lights and timers
Disable audible for key depression,
Disable all outputs 1
Disable lights and timers
Disable all outputs for cavity 1
Disable all outputs for cavity 1
Disable all outputs 1
Disable all outputs 1
Completely disable oven 4
Disable affected oven function 1
Disable affected oven function 1
Disable all cooking functions for cavity
Disable all cooking functions for cavity
Disable all cooking functions for cavity
Disable all cooking functions for cavity
Disable all cooking functions for cavity
Disable all cooking functions for cavity
Disable all cooking functions for cavity
Disable all cooking functions for cavity
Disable all probe functions
Disable all probe functions
Disable Clean and lockout functions 5
Disable Clean and lockout functions 5
mssg 1 (active) / mssg 2 (data)
Disable all cooking functions for cavity
mssg 1 (active) / mssg 2 (data)
Disable all cooking functions for cavity
No change
No action
No change
No action
mssg 1 (active) / mssg 2 (data)
Disable all cooking functions for cavity
mssg 1 (active) / mssg 2 (data)
Disable all cooking functions for cavity
mssg 1 (active) / mssg 2 (data)
Disable Convect, Clean, and lockout functions 4, 5
Turn off light and disable light from door switch
Disable Convect, Clean, and lockout functions 4, 5
Turn off light and disable light from door switch
Disable Clean and lockout functions 4
Disable Clean and lockout functions 4
Disable Clean and lockout functions 4
Disable Clean and lockout functions 4
Disable Clean and lockout functions 4
Disable Clean and lockout functions 4
Message 1:
FAULT DETECTED
PRESS ENTER
TO TRY AGAIN
Message 2:
FEATURE NOT
AVAILABLE
PRESS HELP
2-2
Message 3:
FAULT DETECTED
DISABLE POWER
TO CLEAR
NOTES:
1
“Action Taken” applies as long as the condition exists. If the condition goes away, the control recovers.
2
If there is a cook function or timer active, the function continues. The user cannot edit the function, and [Cancel] will canc el the cook
mode.
3
Flash rate: 0.2 seconds on, 0.1 second off. Pressing any key will clear the display until the fault clears and is re-triggered.
4
“Action Taken” applies until there is a POR (Power On Reset [“hard reset”]).
5
If the control believes the door is locked, it will attempt to unlock it when the function cancels and the cavity temperature cools.
6
Special conditions for latch faults (9dxx):
•
A known good unlock position is defined as when the unlock switch reads closed and lock switch reads open.
•
A known good lock position is defined as when the unlock switch reads open and lock switch reads closed.
•
A faulted switch means the switch input is reading an invalid state, neither open nor closed.
•
Once a latch fault occurs, latch movement is disabled until there is a POR. An error tone w ill sound if a function requiring a
faulted latch is attempted.
•
If at POR, the latch is not at a known good unlock position:
•
If the latch is at a good lock position, it will attempt to unlock when the RTD (Resistance Temperature Device)
temperature is below 400°F.
•
If the latch is not at a good lock position, the control will fault.
•
If a latch fault occurs while the RTD is above the lock temperat ure, the latch will not try to move, but the fault is still logged
to EEPROM after the first stage of detection.
•
The Display column for latch faults applies 1) If the latch was moving when the fault occurred; 2) If the latch is already in a
known locked state when the fault occurs.
•
LOCK flashes after a fault is detected and until the unlocked position is achieved. The unlock position may be
identified by a successful unlock switch closure, or as the result of timing when the unlock switch is not
functioning properly.
•
If the last known good position was unlock (e.g. baking, or idle) and a latch fault occurs, the motor is never moved. The
fault is logged to EEPROM and is not seen by the user.
•
The detection for latch faults is in two stages. The first stage is to let the control recover without moving the latch. Afte r
this:
•
If the latch was previously at a known good unlock position, the latch will not move and the control will fault.
•
If the control was previously in a known good lock position:
•
•
If the RTD is below 400°F, the latch will attempt to recover to it’s proper position (up to three
revolutions). If it cannot, the control will fault and the latch will move to a calculated unlock position.
•
If the RTD is at or above 400°F, the control will fault. W hen the RTD cools to below 400°F, the control
will attempt to recover to a good unlock position (up to three revolution). If it cannot, the control will fault
and the latch will move to a calculated unlock position.
•
Note: If the unlock position cannot be found, this may result in a second fault, the first fault occurring
when the latch request was locked, and the second when the latch request is unlocked.
If the latch is moving when the fault occurs, the control will bypass the first stage of detection and immediately try
to find it’s proper position. If it cannot, the control will fault and the latch will move to a calculated unlock position.
•
Affected DLBs (Double Line Breaks) and loads are disabled during detection.
•
If the control is in a known good unlock position and the lock switch becomes faulted:
•
•
The control will not fault.
•
If a function requiring latch movement is attempted while the lock switch is faulted, the control will sound an error
tone and the function will be disabled.
If the control is in a known good lock position and the unlock switch becomes faulted:
•
The control will not fault.
•
After the function is canceled and unlock is attempted, the control will attempt to unlock the latch according to
the procedures in these notes.
2-3
Step-down transformer
Measure voltage:
Primary terminals ............................ 220 to 240 volts
Secondary terminals ....................... 110 to 120 volts
Oven Sensor and Meat Probe Resistances
OVEN SENSOR
Sensor Type: RTD 1000 W platinum
Calibration:
1654 Ω (350° F/177° C)
Temperature F (C) Resistance (Ohms)
100 (38)
1143
200 (94)
1350
300 (149)
1553
350 (177)
1654
400 (204)
1753
500 (260)
1949
600 (316)
2142
700 (371)
2331
800 (427)
2516
900 (483)
2697
1000 (538)
2874
MEAT PROBE
Type:
NTC Thermistor
Calibration:
9938 Ω (150° F/65.5° C)
Temperature F (C)
Resistance (Ohms)
32 (0)
163300
68 (20)
62450
95 (35)
32660
122 (50)
18020
158 (70)
8760
185 (85)
5360
212 (100)
3400
2-4
NSC ( NON-SELF CLEANING) CONTROLS
Pin Out Locations
3-1
Hidden Functions
Illustration
NSC Controlled
Component
Oven temperature
adjustment
NSC Controlled
Keypad Lockout
NSC Controlled
Temperature display
NSC Controlled
Sabbath Mode
Test Procedure
Press Bake pad.
Enter 550 on the digit-pad.
Immediately press and hold Bake pad
for 3 to 5 seconds.
Oven can be adjusted from -35 to +35
degrees in 5-degree increments by
pressing More + or Less - pads. To
avoid over adjusting the oven, move
temperature 5 degrees each time.
Wait 4 seconds for the data entry
timer to expire to accept the change.
Temperature adjustment will be
retained even through a power failure.
Press and hold Cancel and Timer
pads for 3 to 5 seconds. Press
More + or Less - pads to change.
Press and hold Cancel and Bake
pads for 3 to 5 seconds. Press
More + or Less - pads to change.
Hold Clock pad for 3 to 5 seconds to
activate Sabbath mode.
Hold Clock pad for 3 to 5 seconds to
disable Sabbath mode.
Desired bake function must be
initiated before entering Sabbath
mode.
NSC Controlled
Twelve Hour Off
NSC Controlled
Diagnostic Code
Display
Control will automatically cancel any
cooking operation and remove all relay
drives 12 hours after the last pad
touch.
Press and hold More + pad for 3 to 5
seconds when powering up the unit.
Cycle through the codes using the
More + or Less - pads.
NSC Controlled
One–Watt Standby
Mode
Press and hold Cancel and Less pads for 3 to 5 seconds.
3-2
Results
While increasing or decreasing oven
temperature, this does not affect selfcleaning temperature.
This mode disables keypad input to deter
against accidental keypad entries.
This mode enables the user to indicate
°F or °C on the display.
"SAb" will be displayed and flash for 5
seconds then remain on until timed-out
or cancelled.
The status "SAB" is NOT fault code 5A6.
All pad inputs are disabled except for
CANCEL and CLOCK pads.
This mode disables the normal 12 hour
shutoff to allow operation of the bake
mode for a maximum of 72 hours.
The oven light is not disabled.
See Sabbath mode to disable.
The last 5 diagnostic codes will be stored
in the non-volatile memory.
See "Description of Error Codes"
page 2-1 for explanation.
After 15 minutes in idle, the control will
automatically enter this mode. The LED
display remains active during this mode.
"Quick Test" Mode for Non–Self Clean Control
Follow procedure below to use the quick test mode. Entries must be made within 32 seconds of each other or the
control will exit the quick test mode.
1. Press and hold Cancel and Broil pads for 3 to 5 seconds within 5 minutes of power-up.
2. Once the control has entered the "Quick Test" mode, release both pads.
3. Press each of the following pads indicated in the table below.
NOTE:
First time one of the following pads are pressed it will activate the response.
The second time the pad is pressed it will deactivate the response.
NOTE:
This mode must be entered within the first 5 minutes after power up.
NOTE:
If the temperature sensor is greater than 400° F or if the temperature sensor reaches 400° F while under
test, the Quick Test mode will be disabled.
Display will indicate the following:
Key
[Bake]
[Broil]
[Timer]
[Clock]
[More +]
[Less –]
[Cancel]
Operation
Bake relay activated
Broil relay activated
DLB relay activated
Alternate between ODD LED SEGMENTS and
EVEN LED SEGMENTS on each keypress
EEPROM version number
Code version number
End Factory Test Mode
Enter Diagnostic Code Display Mode by pressing More + for 3 to 5 seconds within 60 seconds of powering
up the control.
The control will store the last 5 error codes.
3-3
Wiring Diagram and Schematic 16023529
!
WARNING
16026465
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
3-4
Wiring Diagram and Schematic
!
16023535 16026468
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
3-5
Wiring Diagram and Schematic
!
16026300
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to range before servicing, unless
testing requires power.
L1
L2
O VEN CONTROL CIRCUIT
AUTO
TRANSFORME R
OVEN
LAMP
OVEN LIGHT
SWITCH
4
2
1
NSC ELEC
3
W HITE
B AK E AN D BR OIL
L2 FO R B AK E A ND BR O IL
4
RED
BROIL
ELEMENT
2
L1
3
RTD
RTD
NEU TR AL
B AK E
BR OIL
1
W HITE
4
3
2
BAKE
ELEMENT
1
OVEN
SENSOR
3-6
Wiring Diagram and Schematic
!
16026685 16026763 16026765
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power and gas to range before servicing,
unless testing requires power and/or gas.
3-7
Wiring Diagram and Schematic
!
16026838
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to range before servicing, unless
testing requires power.
3-8
H1 CONTROLS
TACH SIGNAL
TACH +24V DC
Pin Out Locations
4-1
4-2
Hidden Functions
Illustration
H1 Controlled
Component
Oven temperature
adjustment
H1 Controlled
Temperature display
H1 Controlled
Clock Display
H1 Controlled
24 Hour Clock
H1 Controlled
Factory Default
H1 Controlled
Twelve hour off
H1 Controlled
Sabbath Mode
Test Procedure
Press BAKE pad.
Enter 550 on the digit-pad.
Immediately press and hold BAKE
pad for 3 seconds.
Oven can be adjusted from -35 to +35
degrees in 5-degree increments by
pressing AUTOSET pad. To avoid
over adjusting the oven, move
temperature 5 degrees each time.
Wait 4 seconds for the data entry
timer to expire to accept the change.
Temperature adjustment will be
retained even through a power failure.
Press and hold Cancel and Bake
pads for 3 seconds.
Press and hold Cancel and Clock
pads for 3 seconds.
Press and hold Cancel and Favorite
pads for 3 seconds.
Press and hold Cancel and Keep
Warm pads for 3 seconds.
Control will automatically cancel any
cooking operation and remove all relay
drives 12 hours after the last pad
touch.
Hold CLOCK pad for 3 seconds to
activate Sabbath mode.
Hold CLOCK pad for 3 seconds to
disable Sabbath mode.
H1 Controlled
H1 Controlled
Child lock out
Diagnostic Code
Display
Press and hold Cancel and Cook &
Hold pads for 3 seconds. “OFF” will
display where the temperature
normally appears. “LOCK” will display
flashing while door is locking.
To reactivate the control, press and
hold Cancel and Cook & Hold pads
for 3 seconds.
See “Quick Test Mode”.
Cycle through the codes using the
number pads 1 through 5.
Results
While increasing or decreasing oven
temperature, this does not affect selfcleaning temperature.
This mode enables the user to indicate
°F or °C on the display.
Allows clock to be toggled On or OFF.
Allows the time on the clock to be
toggled from 12 hour or 24 hour display.
Allows the clock to be reset to factory
settings.
See Sabbath mode to disable.
“SAb” will be displayed and flash for
5 seconds.
Display will go back to time of day.
All pad inputs are disabled except for
CANCEL and CLOCK pads.
This mode disables the normal 12 hour
shutoff to allow operation of the bake
mode for a maximum of 72 hours.
This is a safety feature that can be used
to prevent children from accidentally
programming the oven. It disables the
electronic oven control.
Child lockout features must be reset after
a power failure.
The last 5 diagnostic codes will be stored
in the non-volatile memory.
See “Description of Error Codes”
page 2-1 for explanation.
4-3
Testing the User Interface
Amana Matrix
Control Panel Assembly
Continuity is indicated as follows:
1000 – 6600 Ω for Cancel pad
1000 – 15000 Ω for All other pads
16
9
8
1
Jenn-Air Matrix
Control Panel Assembly
Continuity is indicated as follows:
1000 – 6600 Ω for Cancel pad
1000 – 15000 Ω for All other pads
16
9
8
1
Maytag Matrix
Control Panel Assembly
Continuity is indicated as follows:
1000 – 6600 Ω for Cancel pad
1000 – 15000 Ω for All other pads
Delay
CANCEL
Convect
Bake
Bake
Broil
Convect
Roast
Keep
warm
Oven
Light
Clean
Timer
Clock
Cook &
Hold
Favorite
Autoset
16
9
8
1
4-4
Pad
1
2
3
4
5
6
7
8
9
0
Cancel
Clock
Cook & Hold
Broil
Bake
Convect
Clean
Keep Warm
Favorite
Timer
Oven Light
Convect Roast
Trace
5 & 10
4 & 11
4 & 12
4 & 13
5 & 15
4 & 10
11 & 12
12 & 13
13 & 15
4 & 15
1&3
5 & 13
10 & 11
5 & 12
5&7
5 & 11
7 & 13
4&5
7 &15
4&7
7 &12
7 & 11
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Pad
1
2
3
4
5
6
7
8
9
0
Cancel
Clock
Cook & Hold
Broil
Bake
Clean
Keep Warm
Favorite
Timer
Oven Light
Trace
13 & 15
12 & 15
10 & 15
7 & 13
12 & 13
10 & 12
4 & 13
4 & 12
5 & 10
5 & 12
1 & 2/3
4 & 14
5 & 14
13 & 14
7 & 15
5&7
14 & 15
5 & 13
4&5
4 & 10
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Pad
1
2
3
4
5
6
7
8
9
0
Cancel
Clock
Cook & Hold
Broil
Bake
Convect Bake
Convect Roast
Clean
Keep Warm
Favorite
Timer
Oven Light
Trace
13 & 15
12 & 13
12 & 15
4 & 11
4 & 12
4 & 10
5 & 11
5 & 13
5 & 10
5 & 12
1&3
7 & 13
11 & 13
11 & 12
10 & 11
11 & 15
5&7
4 & 13
7 & 11
4&5
4&7
10 & 12
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Testing the User Interface
Matrix
Control Panel Assembly
Continuity is indicated as follows:
1000 – 6600 Ω for Cancel pad
1000 – 15000 Ω for All other pads
16
9
8
1
4-5
Pad
1
2
3
4
5
6
7
8
9
0
Cancel
Clock
Cook & Hold
Broil
Bake
CV Bake
CV Roast
Clean
Keep Warm
Favorites
Timer
Light
Trace
13 & 15
12 & 13
12 & 15
4 & 11
4 & 12
4 & 10
5 & 13
5 & 12
5 & 10
10 & 12
1&2
4&5
4&7
5&7
10 & 11
4 & 13
7 & 11
7 & 15
11 & 12
13 & 14
5 & 11
7 & 13
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Quick Test (Convection Model)
“Quick Test” Mode for Electronic Range Control (Convection Model)
Follow procedure below to use the quick test mode. Entries must be made within 32 seconds of each other or the
control will exit the quick test mode.
1. Press and hold CANCEL and BROIL pads for 3 seconds.
2. Once the control has entered the “Quick Test” mode, release both pads.
3. Press each of the following pads indicated in the table below.
NOTE:
First time one of following pads are pressed it will activate the response.
The second time the pad is pressed it will deactivate the response.
Display will indicate the following:
Pad
Response
BAKE ................................... Bake DLB and Bake relay activated
BROIL.................................. Broil DLB and Broil relay activated
KEEP WARM ...................... Bake DLB and Broil DLB activated
CONVECT BAKE ................ Convection Fan on high speed
CONVECT ROAST ............. Cooling Fan activated
CLEAN................................. MDL relay activated
COOK & HOLD ................... Displays last diagnostic code
FAVORITE .......................... Displays EEPROM version number
TIMER ................................. Displays main code version number
CLOCK ................................ All display segments illuminated
OVEN LIGHT....................... Oven light activated
CANCEL .............................. Exit Quick Test mode
1........................................... Even segments on
2........................................... Odd segments on
3........................................... Convection Ring activated; Convection Ring DLB activated
4........................................... Bake relay activated
5........................................... Broil relay activated
6........................................... Convection relay activated
7........................................... N/A
8........................................... N/A
9........................................... N/A
AUTOSET ........................... Steps through last 5 diagnostic codes
Diagnostic Code Display Mode can be activated by pressing and holding the AUTOSET pad for 3 seconds at
power-up. Diagnostic Code Display Mode can only be started while powering up the control.
4-6
Quick Test
“Quick Test” Mode for Electronic Range Control
Follow procedure below to use the quick test mode. The control will automatically exit quick test mode 10 seconds
after it exits the last test function selected.
1. Press and hold CANCEL and TOAST pads for 3 seconds.
2. Once the control has entered the “Quick Test” mode, release both pads.
3. Press each of the following pads indicated in the table below.
NOTE:
First time one of following pads are pressed it will activate the response. The second time the pad is
pressed it will deactivate the response. The chosen function will be active for 3 seconds.
Display will indicate the following:
Pad
Response
BAKE ................................... Bake, Bake DLB and Broil DLB relays activated
BROIL.................................. Broil, Bake DLB and Broil DLB relays activated
KEEP WARM ...................... Bake DLB and Broil DLB relays activated
CLEAN................................. MDL relay activated
COOK & HOLD ................... Displays last diagnostic code
FAVORITE .......................... Displays EEPROM version number
TIMER ................................. Displays main code version number
CLOCK ................................ All display segments illuminated
OVEN LIGHT....................... Oven light activated
CANCEL .............................. Exit Quick Test mode
DELAY................................. Display last diagnostic code
AUTOSET ........................... Steps through last 5 diagnostic codes
0........................................... N/A
1........................................... Even segments on
2........................................... Odd segments on
3........................................... Bake DLB and Broil DLB relays activated
4........................................... N/A
5........................................... N/A
6........................................... Cooling Fan relay activated
7........................................... N/A
8........................................... N/A
9........................................... N/A
Diagnostic Code Display Mode can be activated by pressing and holding the AUTOSET pad for 3 seconds at
power-up. Diagnostic Code Display Mode can only be started while powering up the control.
4-7
Wiring Diagram and Schematic
!
16022501 16022502
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
4-8
Wiring Diagram and Schematic
!
16026545 16022507
WARNING
To avoid risk of electrical shock, personal injury or death: disconnect power to oven before servicing, unless
testing requires power.
4-9
Wiring Diagram and Schematic
!
16022503
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
4-10
Wiring Diagram and Schematic
!
16022505
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
4-11
Wiring Diagram and Schematic
!
16022508
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires it.
4-12
Wiring Diagram and Schematic
!
16022515
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
4-13
Wiring Diagram and Schematic
!
16027224
16023321
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to range before servicing, unless
testing requires power.
Schematic JER8885QCS Series 14 and later, JER8885QCB Series 15 and later
4-14
Wiring Diagram and Schematic
!
16026291 16026292
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power and gas to range before servicing,
unless testing requires power and/or gas.
4-15
Wiring Diagram and Schematic
!
16026296 16026297 16026298
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to range before servicing, unless
testing requires power.
4-16
Wall Oven Wiring Diagram and Schematic
!
WARNING
16026275 16026568 16026569
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
4-17
Wiring Diagram and Schematic
!
16026851
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power and gas to range before servicing,
unless testing requires power and/or gas.
4-18
Wiring Diagram and Schematic
!
1 6 0 2 7 2 2 6 16022496
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to range before servicing, unless
testing requires power.
Schematic Diagram (Control Circuits), JER8885QAS Series 15 and later
4-19
Wiring Diagram and Schematic
!
16027229
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to range before servicing, unless
testing requires power.
Schematic (Control Circuits) MER5875RAS Series 13, MER5875RAF/B Series 14, MER5875RAN Series 15
4-20
Wiring Diagram and Schematic
!
16027232
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to range before servicing, unless
testing requires power.
Schematic, AER5845RAS Series 13, AER5845RAB/W Series 14
4-21
Wiring Diagram and Schematic
!
16027233
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to range before servicing, unless
testing requires power.
Schematic, MER5875RCQ/S Series 15; MER5875RCB Series 16
4-22
H2 CONTROLS
Pin Out Locations
5-1
Hidden Functions
Controller
H2
Component
Oven temperature
adjustment
H2
Temperature display
H2
Clock display
H2
24-hour clock
H2
Factory default
H2
12-hour off
H2
Sabbath mode
Test Procedure
Press BAKE pad.
Enter 550 on the digit-pad.
Immediately press and hold BAKE
pad for 3 to 5 seconds.
Oven can be adjusted from -35 to +35
degrees in 5-degree increments by
pressing AUTOSET pad. To avoid
over adjusting the oven, move
temperature 5 degrees each time.
Wait 4 seconds for the data entry
timer to expire to accept the change.
Temperature adjustment will be
retained even through a power failure.
Press and hold Cancel and Bake
pads for 3 to 5 seconds.
Press and hold Cancel and Clock
pads for 3 to 5 seconds.
Press and hold Cancel and Favorite
pads for 3 to 5 seconds.
Press and hold Cancel and Keep
Warm pads for 3 to 5 seconds.
Control automatically cancels cooking
operations and removes relay drives
12 hours after the last pad touch.
Hold CLOCK pad for 3 to 5 seconds to
activate Sabbath mode.
Hold CLOCK pad for 3 to 5 seconds to
disable Sabbath mode.
H2
H2
Child lockout
Diagnostic code
display
Press and hold Cancel and Cook &
Hold pads for 3 to 5 seconds. "OFF"
displays where the temperature
normally appears. "LOCK" flashes
while door is locking.
To reactivate the control, press and
hold Cancel and Cook & Hold pads
for 3 to 5 seconds.
See "Quick Test Mode."
Cycle through the codes using the
number pads 1 through 5.
5-2
Results
While increasing or decreasing oven
temperature, this does not affect selfcleaning temperature.
This mode enables the user to indicate
°F or °C on the display.
Allows clock to be toggled on or off.
Allows the time on the clock to be
toggled from 12-hour or 24 -hour display.
Allows the clock to be reset to factory
settings.
See Sabbath mode to disable.
"SAb" flashes for 5 seconds.
Display returns to time of day.
All pad inputs are disabled except for
CANCEL and CLOCK pads.
This mode disables the normal 12 -hour
shutoff to allow operation of the bake
mode for a maximum of 72 hours.
This is a safety feature that can be used
to prevent children from accidentally
programming the oven. It disables the
electronic oven control.
Child lockout features must be reset after
a power failure.
The last 5 diagnostic codes will be stored
in the non-volatile memory.
See "Description of Error Codes"
page 2-1 for explanation.
Testing the User Interface
Control Panel Assembly
(Model JJW8430DD*)
Continuity is indicated as follows:
1000 – 6600 Ω for Cancel pad
1000 – 15000 Ω for all other
pads
18
11
Pad
1
2
3
4
5
6
7
8
9
0
Lower Cancel
Lower Broil
Lower Bake
Delay
Clock
Favorite
Lower Clean
Upper Clean
Upper Cancel
10
1
Lower Light
Upper Keep Warm
Upper Light
Autoset
Lower Keep Warm
Upper Bake
Timer 2
Cook & Hold
Upper Broil
Timer 1
Control Panel Assembly
(Models JJW9130DD*, JJW9330DD*)
Continuity is indicated as follows:
1000 – 6600 Ω for Cancel pad
1000 – 15000 Ω for all other
pads
18
11
Pad
1
2
3
4
5
6
7
8
9
0
Lower Cancel
Lower Broil
Lower Bake
Delay
Clock
Favorite
Lower Clean
Upper Clean
Upper Cancel
10
1
Lower Light
Upper Keep Warm
Upper Light
Autoset
Lower Keep Warm
Upper Bake
Timer 2
Cook & Hold
Upper Broil
Timer 1
Convect Roast
Convect Bake
5-3
Trace
15 & 16
14 & 16
16 & 17
6 & 16
6&7
7 & 17
5&6
5 & 14
6 & 14
14 & 15
1 & 2 or
1&3
8 & 15
7 & 15
5&7
7 & 16
4 & 16
4 & 15
4 & 14
11 & 12 or
11 & 13
14 & 17
4&5
8 & 17
7 & 14
4&8
5 & 15
7&8
5 & 16
8 & 14
8 & 16
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Trace
15 & 16
14 & 16
16 & 17
6 & 16
6&7
7 & 17
5&6
5 & 14
6 & 14
14 & 15
1 & 2 or
1&3
8 & 15
7 & 15
5&7
7 & 16
4 & 16
4 & 15
4 & 14
11 & 12 or
11 & 13
14 & 17
4&5
8 & 17
7 & 14
4&8
5 & 15
7&8
5 & 16
8 & 14
8 & 16
6 & 15
4&7
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Quick Test
"Quick Test" Mode for Electronic Range Control
Follow procedure below to use the quick test mode. Entries must be made within 32 seconds of each other or the
control will exit the quick test mode.
1. Press and hold CANCEL and BROIL pads for 3 to 5 seconds.
2. Once the control has entered the "Quick Test" mode, release both pads.
3. Press each of the following pads indicated in the table below.
NOTE:
First time one of the following pads is pressed it will activate the response.
The second time the pad is pressed it will deactivate the response.
Display will indicate the following:
Pad
Response
BAKE ................................... Bake DLB and Bake relay activated
BROIL.................................. Broil DLB and Broil relay activated
KEEP WARM ...................... Bake DLB and Broil DLB activated
CONVECT BAKE ................ Convection Fan on high speed
CONVECT ROAST ............. Cooling Fan activated
CLEAN................................. MDL relay activated
COOK & HOLD ................... Displays last diagnostic code
FAVORITE .......................... Displays EEPROM version number
TIMER ................................. Displays main code version number
CLOCK ................................ All display segments illuminated
OVEN LIGHT....................... Oven light activated
CANCEL .............................. Exit Quick Test mode
1........................................... Even segments on
2........................................... Odd segments on
3........................................... Convection Ring activated; Convection Ring DLB activated
4........................................... Bake relay activated
5........................................... Broil relay activated
6........................................... Convection relay activated
7........................................... N/A
8........................................... N/A
9........................................... N/A
AUTOSET ........................... Steps through last 5 diagnostic codes
Diagnostic Code Display Mode can be activated by pressing and holding the AUTOSET pad for 3 to 5 seconds at
power-up. Diagnostic Code Display Mode can only be started while powering up the control.
5-4
Wiring Diagram and Schematic
!
16022511 16026546
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires it.
5-5
— NOTES —
5-6
H2.5 CONTROLS
Pin Out Locations
6-1
Pin Out Locations
6-2
Hidden Functions
Illustration
H2.5 Controlled
Component
Oven temperature
adjustment
(Upper Oven)
H2.5 Controlled
Oven temperature
adjustment
(Lower Oven)
H2.5 Controlled
Temperature display
H2.5 Controlled
Clock Display
H2.5 Controlled
24 Hour Clock
H2.5 Controlled
Factory Default
H2.5 Controlled
Twelve hour off
H2.5 Controlled
Sabbath Mode
Test Procedure
Press Upper Bake pad.
Enter 550 on the digit-pad.
Immediately press and hold Upper
Bake pad for 3 seconds.
Oven can be adjusted from -35 to +35
degrees in 5-degree increments by
pressing Autoset pad. To avoid over
adjusting the oven, move temperature
5 degrees each time. Wait 4 seconds
for the data entry timer to expire to
accept the change. Temperature
adjustment will be retained even
through a power failure.
Press Lower Bake pad.
Enter 550 on the digit-pad.
Immediately press and hold Lower
Bake pad for 3 seconds.
Oven can be adjusted from -35 to +35
degrees in 5-degree increments by
pressing Autoset pad. To avoid over
adjusting the oven, move temperature
5 degrees each time. Wait 4 seconds
for the data entry timer to expire to
accept the change. Temperature
adjustment will be retained even
through a power failure.
Press and hold Upper Cancel and
Upper Bake pads for 3 seconds.
Press and hold Upper Cancel and
Clock pads for 3 seconds.
Press and hold Upper Cancel and
Favorite pads for 3 seconds.
Press and hold Upper Cancel and
Upper Keep Warm pads for 3
seconds.
Control automatically cancels/removes
any cooking operations/relay drives 12
hours after the last pad touch.
Hold Clock pad for 3 to 5 seconds to
activate Sabbath mode.
Hold Clock pad for 3 to 5 seconds to
disable Sabbath mode.
H2.5 Controlled
Beeper Volume
H2.5 Controlled
Child lock out
H2.5 Controlled
Diagnostic Code
Display
Hold Upper Cancel and Delay pads
for 3 seconds to adjust beeper
loudness level.
Press and hold Upper Cancel and
Cook & Hold pads for 3 seconds.
“OFF” will display where the
temperature normally appears.
“LOCK” will display flashing while door
is locking.To reactivate the control,
press and hold Cancel and Cook &
Hold pads for 3 seconds.
Press and hold Upper Cancel and
Autoset pads for 3 seconds.
See “Quick Test Mode.”
Cycle through the codes using the
number pads 1 through 5.
6-3
Results
While increasing or decreasing oven
temperature, this does not affect selfcleaning temperature.
While increasing or decreasing oven
temperature, this does not affect selfcleaning temperature.
This mode enables the user to indicate
°F or °C on the display.
Allows clock to be toggled On or OFF.
Allows the time on the clock to be
toggled from 12 hour or 24 hour display.
Allows the clock to be reset to factory
settings.
See Sabbath mode to disable.
“SAbbAth” will display for 5 seconds,
then change to “SAb” (displayed in Temp
area).
All pad inputs are disabled except for
CANCEL and CLOCK pads.
This mode disables the normal 12 hour
shutoff to allow operation of the bake
mode for a maximum of 72 hours.
Volume settings are Low, Medium and
High.
This is a safety feature that can be used
to prevent children from accidentally
programming the oven. It disables the
electronic oven control.
Child lockout features must be reset after
a power failure.
The last 5 diagnostic codes will be stored
in the non-volatile memory.
See “Description of Error Codes”
page 2-1 for explanation.
Testing the User Interface
Component
Control Panel Assembly
Test Procedure
Continuity is indicated as follows:
1000 – 6600 Ω for Cancel pad
1000 – 10000 Ω for All other pads
18
11
10
1
6-4
Pad
1
2
3
4
5
6
7
8
9
0
Lower Cancel
Lower Cancel
Lower Cancel
Upper Cancel
Upper Cancel
Upper Cancel
Conv Bake
Delay
Clock
Favorite
Lower Clean
Upper Clean
Lower Bake
Lower Light
Upper Keep Warm
Upper Light
Autoset
Lower Keep Warm
Conv Roast
Lower Broil
Upper Bake
Timer 2
Cook & Hold
Upper Broil
Timer 1
Drying
Proof
Toast
Results
Trace
14 & 16
16 & 17
6&8
6&7
8 & 17
7 & 14
6 & 15
5 & 14
6 & 14
8 & 14
1&2
2&3
1&3
11 & 12
12 & 13
11 & 13
8 & 16
6 & 16
5 & 16
5&7
4 & 14
14 & 15
5 & 15
15 & 16
6 & 17
7 & 15
14 & 17
4 & 15
8 & 15
4 & 17
7&8
4&7
5&6
7 & 17
4 & 16
4&5
4&8
7 & 16
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Testing the User Interface
Illustration/Component
Control Panel Assembly
Test Procedure
Continuity is indicated as follows:
1000 – 6600 Ω for Cancel and
Warming Zone pads
1000 – 10000 Ω for All other pads
18
11
10
1
6-5
Pad
1
2
3
4
5
6
7
8
9
0
Lower Cancel
Upper Cancel
Convect Bake
Delay
Clock
Favorite
Lower Clean
Upper Clean
Lower Bake
Lower Light
Upper Keep
Warm
Upper Light
Autoset
Lower Keep
Warm
Conv Roast
Lower Broil
Upper Bake
Timer 2
Cook & Hold
Upper Broil
Timer 1
Toast
Warm Zone
Results
Trace
14 & 16
16 & 17
6&8
6&7
8 & 17
7 & 14
6 & 15
5 & 14
6 & 14
8 & 14
1 & 2 or 3
11 & 12 or 13
4 & 15
6 & 16
5 & 16
5&7
5 & 15
7 & 16
8 & 15
7 & 15
7 & 17
15 & 16
14 & 17
8 & 16
4&8
4&5
4 & 14
4&7
5&6
14 & 15
4 & 16
7&8
4 & 6 or 17
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Testing the User Interface
Control Panel Assembly
Continuity is indicated as follows:
Cancel and Warming Zone pads:
1000 – 6600 Ω.
All other pads:
1000 – 10000 Ω.
NOTE: Pins 6 & 9 are jumped
together in control.
NOTE: Pins 1 & 10 and 11 & 18 are
loops in circuit.
18
11
10
1
6-6
Pad
1
2
3
4
5
6
7
8
9
0
Lower Cancel
Lower Cancel
Upper Cancel
Upper Cancel
Conv Bake
Delay
Clock
Favorite
Lower Clean
Upper Clean
Lower Bake
Lower Light
Upper Keep Warm
Upper Light
Autoset
Lower Keep Warm
Conv Roast
Upper Bake
Timer 2
Cook & Hold
Upper Broil
Timer 1
Warm Zone
Warm Zone
Warm Zone
Trace
14 & 16
17 & 16
6&8
7&6
8 & 17
7 & 14
6 & 15
5 & 14
6 & 14
8 & 14
1&2
1&3
11 & 12
11 & 13
4 & 15
16 & 6
5 & 16
5&7
5 & 15
7 & 16
8 & 15
7 & 15
7 & 17
15 & 16
14 & 17
8 & 16
5&4
4 & 14
4&7
6&5
14 & 15
4 & 16
6&4
17 & 4
17 & 6
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Quick Test
“Quick Test” Mode for Electronic Range Control
Follow the procedure below to perform the Electronic Range Control (ERC) quick test. Instructions must be entered
within 32 seconds of each other (via the touch pad) or the ERC will exit the quick test.
1. Press and hold CANCEL and BROIL pads for 3 seconds.
2. Once the control has entered the “Quick Test” mode, release both pads.
3. Press each of the following pads indicated in the table below.
NOTE: Press the applicable pad once to activate the associated response.
Press the applicable pad a second time to deactivate the associated response.
Display will indicate the following:
Pad
Response
BAKE ................................... Bake DLB and Bake relay activated
BROIL.................................. Broil DLB and Broil relay activated
KEEP WARM ...................... Bake DLB and Broil DLB activated
CONVECT BAKE ................ Convection Fan on low speed
CONVECT ROAST ............. Convection Fan on high speed
CLEAN................................. MDL relay activated
COOK & HOLD ................... Displays last diagnostic code
FAVORITE .......................... Displays EEPROM version number
TIMER1 ............................... Displays main code version number
CLOCK ................................ All display segments illuminated
OVEN LIGHT....................... Oven light activated
CANCEL .............................. Exit Quick Test mode
1........................................... Even segments on
2........................................... Odd segments on
3........................................... Convection Ring activated; Convection Ring DLB activated
4........................................... N/A
5........................................... N/A
6........................................... N/A
7........................................... N/A
8........................................... N/A
9........................................... N/A
AUTOSET ........................... Steps through last 5 diagnostic codes
Diagnostic Code Display Mode may be activated at power-up by pressing and holding the AUTOSET pad for 3
seconds. Diagnostic Code Display Mode may be activated only when applying power to the control.
6-7
Wiring Diagram and Schematic
!
16023460 16023506
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
6-8
Wiring Diagram and Schematic
!
16026150
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
6-9
Wiring Diagram and Schematic
!
16027364
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power and gas to range before servicing,
unless testing requires power and/or gas.
6-10
H3 CONTROLS
Pin Out Locations
7-1
Pin Out Locations
7-2
Hidden Functions
Control
H3
Feature
Temperature display
H3
Factory Default
H3
Clock Display
H3
24 Hour Clock
H3
Demo
H3
Twelve hour off
H3
Sabbath Mode
H3
Beeper Volume
H3
Child lock out
H3
Diagnostic Code
Display
Procedure
Press and hold Upper Cancel and
Upper Bake pads for 3 to 5 seconds.
Press and hold Upper Cancel and
Warm pads for 3 to 5 seconds.
Press and hold Upper Cancel and
Clock pads for 3 to 5 seconds.
Press and hold Upper Cancel and
Delay pads for 3 to 5 seconds.
Press and hold Upper Cancel and
Less - pads for 3 to 5 seconds.
Control w ill automatically cancel any
cooking operation and remove all relay
drives 12 hours after the last pad
touch.
Hold Clock pad for 3 to 5 seconds to
activate Sabbath mode.
Hold Clock pad for 3 to 5 seconds to
disable Sabbath mode.
Oven must be in BAKE mode before
enabling SABBATH.
Hold Upper Cancel and More+ pads
for 3 to 5 seconds to adjust beeper
loudness level.
Press and hold Upper Cancel and
Cook & Hold pads for 3 to 5 seconds.
“OFF” will display where the
temperature normally appears.
“LOCK” will display flashing while door
is locking.
To reactivate the control, press and
hold Cancel and Cook & Hold pads
for 3 to 5 seconds.
Press and hold Upper Cancel and
Timer for 3 to 5 seconds within 5
minutes of power up.
See “Quick Test Mode.”
Cycle through the codes.
7-3
Results
Indicates °F or °C on the display.
Resets control to factory settings.
Turns clock display on or off.
Displays either 12-hour or 24-hour time
format.
Enters a demonstrative sales mode.
See Sabbath mode to disable.
"SAb" displays and flashes for 5 seconds.
All pad inputs are disabled except for
CANCEL and CLOCK pads.
This mode disables the normal 12 hour
shutoff to allow operation of the bake mode
for a maximum of 72 hours.
Volume settings are Low, Medium and
High.
This disables the electronic oven control
and prevents children from accidentally
programming the oven.
Child lockout features must be reset after a
power failure.
The last 5 diagnostic codes w ill be stored in
the non-volatile memory.
See “Description of Error Codes”
page 2-1 for explanation.
Hidden Functions
H3 Controlled
Oven temperature
adjustment
(Upper Oven)
H3 Controlled
Oven temperature
adjustment
(Lower Oven)
Press Upper Bake pad.
Enter 550 on the digit-pad.
Immediately press and hold Upper
Bake pad for 3 seconds.
Oven can be adjusted from -35 to +35
degrees in 5-degree increments by
pressing More+ or Less-pads. To
avoid over adjusting the oven, move
temperature 5 degrees each time.
Wait 4 seconds for the data entry
timer to expire to accept the change.
Temperature adjustment will be
retained even through a power failure.
Press Lower Bake pad.
Enter 550 on the digit-pad.
Immediately press and hold Lower
Bake pad for 3 seconds.
Oven can be adjusted from -35 to +35
degrees in 5-degree increments by
pressing More+ or Less- pads. To
avoid over adjusting the oven, move
temperature 5 degrees each time.
Wait 4 seconds for the data entry
timer to expire to accept the change.
Temperature adjustment will be
retained even through a power failure.
7-4
While increasing or decreasing oven
temperature, this does not affect selfcleaning temperature.
While increasing or decreasing oven
temperature, this does not affect selfcleaning temperature.
Testing the User Interface
Control Panel Assembly
MER6875AC*
Continuity is indicated as follows:
1000 – 6600 Ω for Cancel and
Warming Zone pads
1000 – 10000 Ω for All other pads
18
11
10
1
7-5
Pad
1
2
3
4
5
6
7
8
9
0
Lower Cancel
Upper Cancel
Convect Bake
Delay
Clock
Favorite
Lower Clean
Upper Clean
Lower Bake
Lower Light
Upper Keep Warm
Upper Light
Autoset
Lower Keep Warm
Conv Roast
Lower Broil
Upper Bake
Timer 2
Cook & Hold
Upper Broil
Timer 1
Toast
Warm Zone
Trace
14 & 16
16 & 17
6&8
6&7
8 & 17
7 & 14
6 & 15
5 & 14
6 & 14
8 & 14
1 & 2 or 3
11 & 12 or 13
4 & 15
6 & 16
5 & 16
5&7
5 & 15
7 & 16
8 & 15
7 & 15
7 & 17
15 & 16
14 & 17
8 & 16
4&8
4&5
4 & 14
4&7
5&6
14 & 15
4 & 16
7&8
4 & 6 or 17
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Testing the User Interface
7-6
Quick Test
“Quick Test” Mode for Electronic Range Control
Follow the procedure below to perform the Electronic Range Control (ERC) quick test. Instructions must be entered
within 32 seconds of each other (via the touch pad) or the ERC will exit the quick test.
1. Press and hold UPPER CANCEL and BROIL pads for 3 seconds.
2. Once the control has entered the “Quick Test” mode, release both pads.
3. Press each of the following pads indicated in the table below.
NOTE: Press the applicable pad once to activate the associated response.
Press the applicable pad a second time to deactivate the associated response.
Display will indicate the following:
Pad
Response
UPPER BAKE...................... Upper Bake DLB and Upper Bake relay activated
LOWER BAKE..................... Lower Bake DLB and Lower Bake relay activated
TOAST................................. DLB relays activated
UPPER BROIL .................... Upper Broil DLB and Upper Broil relay activated
LOWER BROIL ................... Lower Broil DLB and Lower Broil relay activated
UPPER KEEP WARM ......... Motorized Door Lock - Upper
LOWER KEEP WARM ........ Motorized Door Lock - Lower
OVEN LIGHT....................... Oven lights activated
COOK & HOLD.................... Displays last diagnostic code
LESS (-)............................... Displays EEPROM version number
MORE (+) ............................ Displays main code version number
CLOCK ................................ All display segments illuminated
Diagnostic Code Display Mode is accessed via the Quick Test Mode. To view the last 5 error codes, enter the Quick
Test Mode by pressing and holding the UPPER CANCEL and UPPER BROIL pads for 3 seconds within 5 minutes
of power-up. Diagnostic Code Display Mode may be activated only when applying power to the control.
7-7
Wiring Diagram and Schematic
!
1 6 0 2 7 3 6 2 16023458
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power and gas to range before servicing,
unless testing requires power and/or gas.
7-8
Wiring Diagram and Schematic
!
16026151 16023459 16027360 16027359
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
If Equipped
7-9
Wiring Diagram and Schematic
!
16027363
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power and gas to range before servicing,
unless testing requires power and/or gas.
7-10
M1 / M2 CONTROLS
Pin Out Locations
8-1
Quick Test
"Quick Test" Mode for Electronic Range Control
Follow procedure below to use the quick test mode. Entries must be made within 32 seconds of each other or the
control will exit the quick test mode.
1. Press and hold CANCEL and BROIL pads for 3 seconds.
2. Once the control has entered the "Quick Test" mode, release both pads.
3. Press each of the following pads indicated in the table below.
NOTE:
First time one of following pads are pressed it will activate the response.
The second time the pad is pressed it will deactivate the response.
NOTE:
This mode can only be entered within the first 5 minutes after power up.
NOTE:
If the temperature sensor is greater than 400° F and the Quick Test mode will be disabled if the
temperature sensor reaches 400° F while under test.
Display will indicate the following:
Key
[Bake]
[Broil]
[Keep Warm]
[Cook&Hold]
[Clean]
[Delay] (M1)
[Timer]
[Clock]
[More +]
[Less –]
[Cancel]
Operation
Bake relay activated
Broil relay activated
DLB relay activated
Last Diagnostic Code displayed
Beep sounds
EEPROM Version Number displayed
Main Code Version Number displayed
All Segments On
Even Segments On
Odd Segments On
End Factory Test Mode
Diagnostic Code Display Mode can only be started within 30 seconds when powering up the control.
8-2
Wiring Diagram and Schematic
!
16023318 16023319 16023320 16023323
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to range before servicing, unless
testing requires power.
8-3
Wiring Diagram and Schematic
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
If Equipped
16023542 16026105 16026484 16026485 16026543 16026686 16026688 16026689 16026691 16026813
16026978 16027074 16027075 16027144 16023530 16023531 16023534 16023539 16023481
8-4
Wiring Diagram and Schematic
!
16022504 16022500
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to oven before servicing, unless
testing requires it.
8-5
Wiring Diagram and Schematic
!
16026684 16023524 16026551 16026683
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power and gas to range before servicing,
unless testing requires power and/or gas.
8-6
Wiring Diagram and Schematic
!
16025648 16025645 16025646 16025649 16025650
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
8-7
Wiring Diagram and Schematic
!
16026289
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power and gas to range before servicing,
unless testing requires power and/or gas.
8-8
Wiring Diagram and Schematic
!
16026290
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power and gas to range before servicing,
unless testing requires power and/or gas.
8-9
Wiring Diagram and Schematic
!
16026294
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to range before servicing, unless
testing requires power.
8-10
Wiring Diagram and Schematic
!
16026295
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to range before servicing, unless
testing requires power.
8-11
Wiring Diagram and Schematic
!
16026791 16026106 16026792
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power and gas to range before servicing,
unless testing requires power and/or gas.
8-12
Wiring Diagram and Schematic
!
16026797
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power and gas to range before servicing,
unless testing requires power and/or gas.
8-13
Wiring Diagram and Schematic
!
16026853
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to range before servicing, unless
testing requires power.
8-14
Wiring Diagram and Schematic
!
To avoid risk of electrical shock, personal injury
testing requires power.
16027221
WARNING
or death; disconnect power to range before servicing, unless
8-15
Wiring Diagram and Schematic
!
1 6 0 2 7 2 2 2 16027246
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power and gas to range before servicing,
unless testing requires power and/or gas.
8-16
Wiring Diagram and Schematic
!
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to range before servicing, unless
testing requires power.
If Equipped
16027227 16027230 16027231 16027236 16027237 16027245 16027247
8-17
Wiring Diagram and Schematic
!
16027225
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power and gas to range before servicing,
unless testing requires power and/or gas.
8-18
Wiring Diagram and Schematic
!
16027255
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to range before servicing, unless
testing requires power.
8-19
— NOTES —
8-20
Pin Out Locations
EOC III CONTROLS
9-1
Pin Out Locations
9-2
Hidden Functions
Control Component
Switch membrane assembly
NOTE: To avoid equipment
damage, use caution when
checking electronic control
circuitry.
JGS9900BD*
Test Procedure
Closed circuitry resistance
(defined as continuity): 2000 Max Ω
Pins 1 & 10 are shorted together for control
configuration purposes
Latch
Trace # 1
See Detail B
Detail B
Pad
1
2
3
4
5
6
7
8
9
0
Cancel
Bake
Broil
Convect
Clean
Favorites
Rapid Preheat
Vent Fan
More Options
Setup
ATM 1
ATM 2
Back
Enter
Timer 1
Timer 2
Oven Light
Results
Trace
2&7
2&8
2&9
2 & 10
2 & 11
2 & 12
3&6
3&7
3&8
2&6
4&9
4 & 10
4 & 11
5&9
5&7
4 & 12
5 & 10
5 & 11
5&8
5&6
4&6
4&7
3&9
3 & 10
3 & 11
3 & 12
4&8
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Electronic Oven Control (EOC) III Testing Procedures
Warm
Drawer
ATM PADS
ELECTRONIC OVEN CONTROL (EOC) III TESTING/PROGRAMMING PROCEDURES
Feature
Access Procedure
Modification Procedure
Control Reset
Press the Setup pad, then press the right
Press and hold the Back and Enter pads for 5
Resets control to factory default
seconds to enter SERVICE menu options.
ATM pad until SERVICE displays. Press the
values.
Press the right ATM pad to scroll to CONTROL
left ATM pad to select SERVICE menu
options.
RESET. Press the left
ATM pad to select
CONTROL RESET, then press the left
ATM pad
again to reset the control logic. Press
Setup to
exit.
Enter the offset temperature setting desired
Oven Temperature Adjustment
Press the Setup pad, then press the right
Determines oven cavity offset
using the digits pads. Press the right ATM pad
ATM pad until TEMP ADJUST displays.
temperature (range from -35° F to
for + temperature adjustment, or the left ATM
Press the left ATM pad to select oven TEMP
+35° F, or -21° C to +21° C).
pad for – temperature adjustment. Press 0 to
ADJUSTMENT settings.
reset control back to no temperature
adjustment. Wait 3 seconds for the control to
accept the request. Press Setup to exit.
Sabbath Mode
Press the Setup pad, then press the right
Press the left ATM pad to select Manual
Based on the Jewish guidelines for
ATM pad until SABBATH displays. Press the
Sabbath mode, or the right ATM pad to select
Sabbath/Holiday requirements.
left ATM pad to select SABBATH settings.
Auto Sabbath mode. Press the left ATM pad to
turn on Sabbath mode, or the right ATM pad to
turn off Sabbath mode. Press Setup to exit.
9-3
Hidden Functions
Feature
Time Options
Determines control time, day of
week, 12/24 hour clock.
Time Set
Determines time of day to display
on control.
Access Procedure
Press the Setup pad, then the left ATM pad
to select TIME OPTIONS.
Modification Procedure
Press the right ATM pad to scroll to the
desired function to modify.
Press the Setup pad, then the left ATM pad,
then the left ATM pad again to set the time of
day clock.
Day of Week
Determines day of week (Monday
thru Sunday) to display on control
Press the Setup pad, then the left ATM pad,
then press the right ATM pad until DAY
displays. Press the left ATM pad to set the
day of the week.
Press the Setup pad, then the left ATM pad,
then press the right ATM pad until 12/24HR
displays. Press the left ATM pad to select
12/24 HR clock.
Press the Setup pad, then press the right
ATM pad until DISABLE displays. Press the
left ATM pad to select DISABLE settings.
Enter the correct time using the digits pads
and press Enter. Press the left ATM pad to
select AM or the right ATM pad to select PM.
Press Setup to exit.
Press the right ATM pad until the correct day
displays, then press the left ATM pad to select.
Press Setup to exit.
12/24-Hour Clock Display
Determines 12-hour or 24-hour
clock display on control.
Clock & Day Display Disable
Determines if time of day and day of
week will display on control.
Language Display
Determines language display on
control (English, French, Spanish).
C/F (Celsius/Fahrenheit) Display
Determines temperature display on
control (C or F).
Auto Convection
When enabled, reduces the
Convection Bake and Pastry
temperatures by 25° F (-3.9° C).
Tone Options
Determines cook tones, timer tones
and volume settings.
12-Hour Shutoff
Disables 12-hour shuto ff, allowing
the oven to operate indefinitely.
208/240 V Setting
Determines range operating voltage
(208 or 240 VAC).
Cook Tones
Determines the number and duration
of cook time reminder chimes.
Press the Setup pad, then press the right
ATM pad until LANGUAGE displays. Press
the left ATM pad to set LANGUAGE settings.
Press the Setup pad, then press the right
ATM pad until C/F displays. Press the left
ATM pad to select C/F settings.
Press the Setup pad, then press the right
ATM pad until AUTO CONVECT displays.
Press the left ATM pad to select AUTO
CONVECT settings.
Press the Setup pad, then press the right
ATM pad until TONES displays. Press the
left ATM pad to select TONES options.
Press the Setup pad, then press the right
ATM pad until 12HR Shutoff displays. Press
the left ATM pad to select 12-HOUR
SHUTOFF settings.
Press the Setup pad, then press the right
ATM pad until 208/240 displays. Press the
left ATM pad to select 208/240 V settings.
Press the Setup pad, then press the right
ATM pad until TONES displays. Press the
left ATM pad. Press the left ATM pad again
to select COOK TONES settings.
Timers Tones
Determines the number and
duration of timer reminder chimes.
Press the Setup pad, then press the right
ATM pad until TONES displays. Press the
left ATM pad. Press the right ATM pad to
scroll to TIMERS TONES. Press the left
ATM pad to select TIMERS TONES settings.
Volume
Determines volumes of cook and
timer tones.
Press the Setup pad, then press the right
ATM pad until TONES displays. Press the
left ATM pad to select VOLUME settings.
9-4
Press the left ATM pad to select 12-hour clock,
or the right ATM pad to select 24-hour clock.
Press Setup to exit.
Press the left ATM pad to select TIME, or the
right ATM pad to scroll to DAY, then press the
left ATM pad. Press the left ATM pad to turn
display on or the right ATM pad to turn display
off. Press Setup to exit.
Press the right ATM pad until the desired
language displays (English, French, Spanish).
Press the left ATM pad. Press Setup to exit.
Press the left ATM pad to select Celsius or the
right ATM pad to select Fahrenheit. Press
Setup to exit.
Press the left ATM pad to turn on auto
convect, or the right ATM pad to turn off auto
convect. Press Setup to exit.
Press the right ATM pad to scroll to the
desired tone to modify. Press Setup to exit.
Press the left ATM pad to turn on 12-hour
shutoff, or the right ATM pad to turn off 12hour shuto ff. Press Setup to exit.
Press the left ATM pad to select 208 VAC, or
the right ATM pad to select 240 VAC. Press
Setup to exit.
Press the left ATM pad to select 1 – 30 (1
chime every 30 seconds after the initial 4
chimes), or press the right ATM pad to scroll to
1 – 60 (1 chime every 60 seconds after the
initial 4 chimes) or 1 BEEP (no additional
chimes after the initial 4 chimes). Press the
left ATM pad to select the desired setting.
Press Setup to exit.
Press the left ATM pad to select 2 – 30, or 2
chimes every 30 seconds for up to 5 minutes
(after the initial chime), or press the right ATM
pad to scroll to 2 – 60, or 2 chimes every 60
seconds for up to 30 minutes (after the initial
chime), or 1 BEEP (no additional chimes after
the initial chime). Press the left ATM pad to
select the desired setting. Press
Setup to exit.
Press the right ATM pad until VOLUME
displays. Press the left ATM pad. Press the
left ATM pad to select HIGH, or the right ATM
pad to scroll to MEDIUM or LOW. Press the
left ATM pad to select. Press Setup to exit.
Hidden Functions
Feature
Energy Saver Mode
Enables a 1 watt standby
feature. If no pad is pressed
within 5 minutes, the control
enters into a sleep mode.
Demo Mode
Enables a 1 watt standby
feature. If no pad is pressed
within 5 minutes, the control
enters into a sleep mode.
Service Mode
Enables access to service
menus.
Test Access
Enables access to service
menus.
Access Procedure
Press the Setup pad, then press the right ATM
pad until ENERGY SAVER displays. Press the
left ATM pad to select ENERGY SAVER mode
settings.
Modification Procedure
Press the left ATM pad to enter the energy saver
mode or the right ATM pad to exit the energy
saver mode.
Press the Setup pad, then press the right ATM
pad until DEMO displays. Press the left
ATM
pad to select DEMO mode settings.
Press the left ATM pad to enable the DEMO
mode or the right ATM pad to exit the DEMO
mode. Once the DEMO mode begins, press any
key to exit. Press Setup to exit, also.
Press the Setup pad, then press the right ATM
pad until SERVICE displays. Press the left
ATM
pad to select SERVICE menu options.
Press the Setup pad, then press the right ATM
pad until SERVICE displays. Press the left
ATM
pad to select SERVICE menu options.
Faults Access
Displays the 10 most recent
faults produced by the
controller.
Press the Setup pad, then press the right ATM
pad until SERVICE displays. Press the left
ATM
pad to select SERVICE menu options.
Software Versions Access
Displays the software and
EEPROM revision levels.
Press the Setup pad, then press the right ATM
pad until SERVICE displays. Press the left
ATM
pad to select SERVICE menu options.
Display Test
Illuminates all lamps on the
control.
Press the Setup pad, then press the right ATM
pad until SERVICE displays. Press the left
ATM
pad to select SERVICE menu options.
Control Lockout
Disables the touch keypad
control and lo cks the oven
cavity door.
Press the Back and Setup pads simultaneously
for 5 seconds to lock.
Press and hold the Back and Enter pads for 5
seconds to enter SERVICE menu options. Press
Setup to exit.
Press and hold the Back and Enter pads for 5
seconds to enter SERVICE menu options. Press
the right ATM pad to scroll to TEST menu. Press
the left ATM pad to select TEST options. Press
Setup to exit.
Press and hold the Back and Enter pads for 5
seconds to enter SERVICE menu options. Press
the right ATM pad to scroll to the FAULTS menu.
Press the left ATM pad to select FAULTS
options. Press Setup to exit.
Press and hold the Back and Enter pads for 5
seconds to enter SERVICE menu options. Press
the right ATM pad to scroll to the VERSIONS
menu. Press the left ATM pad to view. Press
Setup to exit.
Press and hold the Back and Enter pads for 5
seconds to enter SERVICE menu options. Press
the right ATM pad to scroll to DISPLAY TEST.
Press the left ATM pad. Press Setup to exit.
Press the Back and Setup pads simultaneously
for 5 seconds to unlock.
MODE
Bake
Broil
Clean
COOLING FAN TEMPERATURES
FAN ON TEMP F (C)
FAN OFF TEMP F (C)
350 (177)
300 (149)
Six (6) minute delay
225 (107)
after cycle started
Six (6) minute delay
225 (107)
after cycle started
9-5
Testing the User Interface
Control Component
Switch membrane assembly
JES8850BC*
Test Procedure
Closed circuitry resistance
(defined as continuity): 2000 Max Ω
Pins 1 & 9 are shorted together for control
configuration purposes
Latch
Trace # 1
See Detail B
Detail B
Switch membrane assembly
JES9900BC*
JES9860BC*
Closed circuitry resistance
(defined as continuity): 2000 Max Ω
Pins 1 & 10 are shorted together for control
configuration purposes
Latch
Trace # 1
See Detail B
Detail B
9-6
Pad
1
2
3
4
5
6
7
8
9
0
Cancel
Bake
Broil
Convect
Clean
Favorites
Rapid Preheat
Warm Zone
More Options
Setup
ATM 1
ATM 2
Back
Enter
Timer 1
Timer 2
Oven Light
Pad
1
2
3
4
5
6
7
8
9
0
Cancel
Bake
Broil
Convect
Clean
Favorites
Rapid Preheat
Vent Fan
More Options
Setup
ATM 1
ATM 2
Back
Enter
Timer 1
Timer 2
Oven Light
Results
Trace
2&7
2&8
2&9
2 & 10
2 & 11
2 & 12
3&6
3&7
3&8
2&6
4&9
4 & 10
4 & 11
5&9
5&7
4 & 12
5 & 10
5 & 12
5&8
5&6
4&6
4&7
3&9
3 & 10
3 & 11
3 & 12
4&8
Trace
2&7
2&8
2&9
2 & 10
2 & 11
2 & 12
3&6
3&7
3&8
2&6
4&9
4 & 10
4 & 11
5&9
5&7
4 & 12
5 & 10
5 & 11
5&8
5&6
4&6
4&7
3&9
3 & 10
3 & 11
3 & 12
4&8
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Testing the User Interface
Control Testing Procedures
Control Component
Switch membrane assembly
Test Procedure
Closed circuitry resistance
(defined as continuity): 2000 Max Ω
Pins 1 & 10 are shorted together for control
configuration purposes
Latch
Trace # 1
See Detail B
Detail B
Pad
1
2
3
4
5
6
7
8
9
0
Cancel
Bake
Broil
Clean
Convect
Favorites
Rapid Preheat
Vent Fan
More Options
Setup
ATM 1
ATM 2
Back
Enter
Timer 1
Timer 2
Oven Light
Cooling Fan Temperatures
MODE
Bake
Broil
Clean
COOLING FAN TEMPERATURES
FAN ON TEMP F (C)
FAN OFF TEMP F (C)
300° (148.9°)
275° (135°)
Immediately
275° (135°)
Immediately
275° (135°)
9-7
Results
Trace
2&7
2&8
2&9
2 & 10
2 & 11
2 & 12
3&6
3&7
3&8
2&6
4&9
4 & 10
4 & 11
5&7
5&9
4 & 12
5 & 10
5 & 11
5&8
5&6
4&6
4&7
3&9
3 & 10
3 & 11
3 & 12
4&8
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Testing the User Interface
Control Component
Switch membrane assembly
JDS9865BD*
Test Procedure
Closed circuitry resistance
(defined as continuity): 2000 Max Ω
Pins 1 & 7 are shorted together for control
configuration purposes
Latch
Trace # 1
See Detail B
Detail B
Control Component
Switch membrane assembly
JES8750BA*
Test Procedure
Closed circuitry resistance
(defined as continuity): 2000 Max Ω
Pins 1 & 6 are shorted together for control
configuration purposes
Latch
Trace # 1
See Detail B
Detail B
9-8
Pad
1
2
3
4
5
6
7
8
9
0
Cancel
Bake
Broil
Convect
Clean
Favorites
Rapid Preheat
Vent Fan
More Options
Setup
ATM 1
ATM 2
Back
Enter
Timer 1
Timer 2
Oven Light
Pad
1
2
3
4
5
6
7
8
9
0
Cancel
Bake
Broil
Clean
Favorites
More Options
Warm Zone
Setup
ATM 1
ATM 2
Back
Enter
Timer 1
Timer 2
Oven Light
Results
Trace
2&7
2&8
2&9
2 & 10
2 & 11
2 & 12
3&6
3&7
3&8
2&6
4&9
4 & 10
4 & 11
5&9
5&7
4 & 12
5 & 10
5 & 11
5&8
5&6
4&6
4&7
3&9
3 & 10
3 & 11
3 & 12
4&8
Results
Trace
2&7
2&8
2&9
2 & 10
2 & 11
2 & 12
3&6
3&7
3&8
2&6
4&9
4 & 10
4 & 11
5&7
4 & 12
5&8
5 & 12
5&6
4&6
4&7
3&9
3 & 10
3 & 11
3 & 12
4&8
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Testing the User Interface
Control Component
Switch membrane assembly
JDS8850BD*
Test Procedure
Closed circuitry resistance
(defined as continuity): 2000 Max Ω
Pins 1 & 7 are shorted together for control
configuration purposes
Latch
Trace # 1
See Detail B
Detail B
Switch membrane assembly
JDS9860BD*
Closed circuitry resistance
(defined as continuity): 2000 Max Ω
Pins 1 & 7 are shorted together for control
configuration purposes
Latch
Trace # 1
See Detail B
Detail B
9-9
Pad
1
2
3
4
5
6
7
8
9
0
Cancel
Bake
Broil
Convect
Clean
Favorites
Rapid Preheat
Warming Drawer
More Options
Setup
ATM 1
ATM 2
Back
Enter
Timer 1
Timer 2
Oven Light
Pad
1
2
3
4
5
6
7
8
9
0
Cancel
Bake
Broil
Convect
Clean
Favorites
Rapid Preheat
Vent Fan
More Options
Setup
ATM 1
ATM 2
Back
Enter
Timer 1
Timer 2
Oven Light
Results
Trace
2&7
2&8
2&9
2 & 10
2 & 11
2 & 12
3&6
3&7
3&8
2&6
4&9
4 & 10
4 & 11
5&9
5&7
4 & 12
5 & 10
5 & 11
5&8
5&6
4&6
4&7
3&9
3 & 10
3 & 11
3 & 12
4&8
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Trace
2&7
2&8
2&9
2 & 10
2 & 11
2 & 12
3&6
3&7
3&8
2&6
4&9
4 & 10
4 & 11
5&9
5&7
4 & 12
5 & 10
5 & 11
5&8
5&6
4&6
4&7
3&9
3 & 10
3 & 11
3 & 12
4&8
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Testing the User Interface
Control Component
Switch membrane assembly
JES9750BA*
Test Procedure
Closed circuitry resistance
(defined as continuity): 2000 Max Ω
Pins 1 & 11 are shorted together for control
configuration purposes
Latch
Trace # 1
See Detail B
Detail B
Switch membrane assembly
JES9860BA*
Closed circuitry resistance
(defined as continuity): 2000 Max Ω
Pins 1 & 10 are shorted together for control
configuration purposes
Latch
Trace # 1
See Detail B
Detail B
9-10
Pad
1
2
3
4
5
6
7
8
9
0
Cancel
Bake
Broil
Clean
Favorites
Vent Fan
More Options
Setup
ATM 1
ATM 2
Back
Enter
Timer 1
Timer 2
Oven Light
Pad
1
2
3
4
5
6
7
8
9
0
Cancel
Bake
Broil
Convect
Clean
Favorites
Rapid Preheat
Vent Fan
More Options
Setup
ATM 1
ATM 2
Back
Enter
Timer 1
Timer 2
Oven Light
Results
Trace
2&7
2&8
2&9
2 & 10
2 & 11
2 & 12
3&6
3&7
3&8
2&6
4&9
4 & 10
4 & 11
5&7
4 & 12
5 & 11
5&8
5&6
4&6
4&7
3&9
3 & 10
3 & 11
3 & 12
4&8
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Trace
2&7
2&8
2&9
2 & 10
2 & 11
2 & 12
3&6
3&7
3&8
2&6
4&9
4 & 10
4 & 11
5&9
5&7
4 & 12
5 & 10
5 & 11
5&8
5&6
4&6
4&7
3&9
3 & 10
3 & 11
3 & 12
4&8
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Testing the User Interface
Control Component
Switch membrane assembly
JES8850BA*
Test Procedure
Closed circuitry resistance
(defined as continuity): 2000 Max Ω
Pins 1 & 9 are shorted together for control
configuration purposes
Latch
Trace # 1
See Detail B
Detail B
9-11
Pad
1
2
3
4
5
6
7
8
9
0
Cancel
Bake
Broil
Convect
Clean
Favorites
Rapid Preheat
Warm Drawer
Warm Zone
More Options
Setup
ATM 1
ATM 2
Back
Enter
Timer 1
Timer 2
Oven Light
Results
Trace
2&7
2&8
2&9
2 & 10
2 & 11
2 & 12
3&6
3&7
3&8
2&6
4&9
4 & 10
4 & 11
5&9
5&7
4 & 12
5 & 10
5 & 11
5 & 12
5&8
5&6
4&6
4&7
3&9
3 & 10
3 & 11
3 & 12
4&8
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Quick Test
"Quick Test" Mode for EOC III
Follow the procedure below to perform the EOC III quick test. Once the control is in the quick test mode, any relay
may be activated in any sequence. The test mode will be exited after 10 minutes of inactivity (no pads pressed
within 10 minutes).
1.
2.
3.
4.
5.
6.
7.
Press the Setup pad, then press the right ATM pad.
Press the left ATM pad, then press and hold Back and Enter pads for 5 seconds to enter SERVICE menu options.
Press the right ATM pad to scroll to the TEST menu.
Press the left ATM pad to select TEST options.
Press the left ATM pad again to enter the "Quick Test " mode.
Press each of the following pads indicated in the table below.
Press Cancel or Setup pads to exit.
NOTE:
Press and hold the applicable pad to activate the associated response.
Release the applicable pad to deactivate the associated response.
The control automatically enters the engineering mode so vi sual feedback of relay operations is available on the
control display. Any time a load is activated, the cooling
fan is activated. When the load is deactivated, the cooling
fan is also deactivated.
Display will indicate the following:
Pad
Response
BAKE....................................................Bake
relay activated.
BROIL ..................................................Broil relay activated.
CONVECT ...........................................Convection Bake and C
ooling Fan relays activated.
OVEN LIGHT .......................................Oven light relay activated.
RAPID PREHEAT ................................Convection Fan (HIGH/LOW) activated.
WARMING ZONE ................................Warming Zone relay activated.
VENT (DOWNDRAFT) FAN ................Vent Fan relay activated.
CLEAN .................................................Motorized Door Lock relay activated.
SETUP .................................................1 Second Beep.
FAN ......................................................Downdraft Fan (HIGH/LOW) relay activated.
WARMING DRAWER ..........................Warming Drawer (HIGH/LOW) relay activated.
9-12
Wiring Diagram and Schematic
!
1 6 0 2 6 9 2 5 16026924
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power and gas to range before servicing,
unless testing requires power and/or gas.
9-13
Wiring Diagram and Schematic
!
16026927
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to range before servicing, unless
testing requires power.
9-14
Wiring Diagram and Schematic
!
1 6 0 2 6 9 2 8 16026930 16027004 16027013
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to range before servicing, unless
testing requires power.
9-15
Wiring Diagram and Schematic
!
16027248
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power and gas to range before servicing,
unless testing requires power and/or gas.
9-16
Wiring Diagram and Schematic
!
16027306
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to range before servicing, unless
testing requires power.
9-17
Wiring Diagram and Schematic
!
1 6 0 2 7 3 0 7 16027308
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to range before servicing, unless
testing requires power.
9-18
Wiring Diagram and Schematic
!
16027309
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power and gas to range before servicing,
unless testing requires power and/or gas.
9-19
Wiring Diagram and Schematic
!
16027310
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power and gas to range before servicing,
unless testing requires power and/or gas.
9-20
Pin Out Locations
UH CONTROLS
10-1
Hidden Functions
Illustration
UH2 Controlled
Component
Oven temperature
adjustment
UH2 Controlled
Temperature display
UH2 Controlled
Clock Display
UH2 Controlled
12 Hour Shutoff
UH2 Controlled
Demo mode
UH2 Controlled
Energy Saver
UH2 Controlled
208/240 V mode
UH2 Controlled
Control Lockout
Test Procedure
Press SETUP pad.
Press DOWN ARROW to scroll down
to TEMP ADJUST.
Select oven and enter desired
temperature change. Press ENTER
pad to accept the change.
Oven can be adjusted from -35 to +35
degrees inputting 5 or 35 degrees by
pressing +/- pad. To avoid over
adjusting the oven, move temperature
5 degrees each time. Wait 4 seconds
for the data entry timer to expire to
accept the change. Temperature
adjustment will be retained even
through a power failure.
Press SETUP pad and use the arrow
pad to scroll to the next screen. Select
C/F, then select SET. Press SETUP
pad to exit.
Press SETUP pad. Press CLOCK
pad. Press TIME and enter numeric
from key pad. Select AM or PM.
Press SETUP to end. Press SETUP
pad. Press CLOCK pad. Press DAY
pad. Press back forward to select day
of week. Press SETUP to end. Press
SETUP pad. Press CLOCK pad.
Scroll down to 12/24 HR. Scroll down
to 12/24 HR format. Select SET to
activate. Press SETUP pad to exit.
Press DOWN ARROW pad to scroll
to CLOCK.
Press SETUP pad. Press DOWN
ARROW pad to scroll to 12 HOUR
SHUTOFF pad. Select ON or OFF.
Select SET pad to activate. Press
SETUP pad to exit.
Press SETUP pad. Press DOWN
ARROW pad to scroll to DEMO pad.
Select DEMO to activate. Press
SETUP pad to exit.
Press SETUP pad. Press DOWN
ARROW pad to scroll to ENERGY
SAVER pad. Select ON or OFF.
Select SET pad to activate. Press
SETUP pad to exit.
Press SETUP pad. Press DOWN
ARROW pad to scroll to 208/240 V
pad. Select 208 or 240. Select SET
pad to activate.
Press and hold BACK and ENTER
pads for 5 seconds.
To reactivate the control, press and
hold BACK and ENTER pads for 5
seconds.
10-2
Results
While increasing or decreasing oven
temperature, this does not affect broiling
or self-cleaning temperature.
The oven offset does not need to be
readjusted if there is a power failure.
This mode enables the user to indicate
°F or °C on the display.
Set clock, day of week, or 12/24 HR
clock.
Allows the time on the clock to be
toggled from 12 hour or 24 hour display.
Control will automatically cancel any
cooking operation and remove all relay
drives 12 hours after the last pad touch.
To save energy, the display will turn off
after five minutes of no use in time of day
mode only.
For improved results when using Radiant
Bake only, the oven can be set from 240
V to 208 V.
This is a safety feature that can be used
to prevent accidentally programming the
oven. It disables the electronic oven
control and locks the cavity door(s).
Control lockout features must be reset
after a power failure.
Test Mode
UH2 Controlled
Sabbath Mode
Press SETUP pad. Press DOWN
ARROW pad. Press SABBATH pad to
activate Sabbath mode.
Select AUTO or MANUAL pad. If
AUTO selected, press continue. If
MANUAL selected, press ON or OFF.
Select SET pad.
Auto-Sabbath mode will display a
reminder at 2:00 PM on Friday.
Manual-Sabbath mode will be instantly
programmed for 72 hours.
This mode disables the normal 12 hour
energy saving mode.
The time of day and day of week must
be set correctly for this feature to be
activated.
Test Mode
Follow procedure below to access the Test Mode.
1. Press SETUP pad.
2. Press DOWN ARROW pad three times until SERVICE is displayed.
3. Press SERVICE pad.
4. Press and hold BACK and ENTER pads for 5 seconds.
5. Press TEST pad.
NOTE: If the oven cavity temperature is greater then 400°F, the Test Mode cannot be activated or will abort the
mode if activated.
NOTE: Once the Test Mode is activated and a function is selected the control will activate the relay until the pad is
pressed again. Upon entering TEST Mode all relays are turned off except the DLB relays, which are turned
on. All relays are turned off when the TEST Mode is exited.
Pad Pressed
Relay or Action Activated
Beep
1 Second Beep
Version
Version of software
Last Fault
Display last error code and oven configuration (single, double, convection, nonconvection)
DISP Test
Display segments
UBAKE
Upper Bake Element
UBROIL
Upper Broil Element
UCONV
Upper Convection Element
UCOOL
Upper Cooling Fan
UCONV-H
Upper High Speed Convection Fan
UCONV-L
Upper Low Speed Convection Fan
UMDL
Upper Motorized Door Lock
ULITE
Upper Oven Light
LBAKE
Lower Bake Element
LBROIL
Lower Broil Element
LCONV
Lower Convection Element
LCOOL
Lower Cooling Fan
LCONV-H
Lower High Speed Convection Fan
LCONV-L
Lower Low Speed Convection Fan
LMDL
Lower Motorized Door Lock
LLITE
Lower Oven Light
10-3
Wiring Diagram and Schematic
!
16022512
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires it.
10-4
Wiring Diagram and Schematic
!
16026101 16022823
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
Control Circuits
10-5
Wiring Diagram and Schematic
!
16025884
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
10-6
Wiring Diagram and Schematic
!
16025885
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
10-7
Wiring Diagram and Schematic
!
16026100
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
10-8
PRODUCT SPECIFICATIONS
AND
WARRANTY INFORMATION SOURCES
IN THE UNITED STATES:
FOR PRODUCT SPECIFICATIONS AND WARANTY INFORMATION CALL:
FOR WHIRLPOOL PRODUCTS: 1-800-253-1301
FOR KITCHENAID PRODUCTS: 1-800-422-1230
FOR ROPER PRODUCTS: 1-800-447-6737
FOR TECHNICAL ASSISTANCE WHILE AT THE CUSTOMER’S HOME CALL:
THE TECHNICAL ASSISTANCE LINE: 1-800-832-7174
HAVE YOUR STORE NUMBER READY TO IDENTIFY YOU AS AN
AUTHORIZED IN-HOME SERVICE PROFESSIONAL
FOR LITERATURE ORDERS:
PHONE: 1-800-851-4605
FOR TECHNICAL INFORMATION AND SERVICE POINTERS:
www.servicematters.com
IN CANADA:
FOR PRODUCT SPECIFICATIONS AND WARRANTY INFORMATION CALL:
1-800-461-5681
FOR TECHNICAL ASSISTANCE WHILE AT THE CUSTOMER’S HOME CALL:
THE TECHNICAL ASSISTANCE LINE: 1-800-488-4791
HAVE YOUR STORE NUMBER READY TO IDENTIFY YOU AS AN
AUTHORIZED IN-HOME SERVICE PROFESSIONAL