Panamax MD2-ZB BlueBOLT 2 OUTLET Surge Protector Installation instructions
Add to My manuals2 Pages
Panamax MD2-ZB is a surge protector with ZigBee connectivity that allows you to remotely control and monitor your plugged-in devices. It has two AC outlets with individual power control, allowing you to turn on or off each outlet independently. The MD2-ZB also features a network connection status indicator that lets you know if it's connected to a ZigBee network. Additionally, it has a wiring fault light that indicates any improper wiring in the outlet it's plugged into, ensuring safety.
advertisement
OPTIONS FOR MOUNTING & FRONT COVER FACEPLATE
Cover of MD2-ZB can easily be removed by pulling off cover at the two side indents ( 1).
Cover can be flipped around 180 degrees to hide LEDs from front straight-on view if desired.
2
1
Unit can be securely screwed into wall outlet faceplate using either hole ( 2) indicated (screw is included).
SPECIFICATIONS
Electrical Ratings
Line Voltage ______ 120 Vac, 60Hz
Current Rating _____ 12 A
Voltage Protection Rating (UL 1449 3rd Edition,
3,000A) _________ 400V L-N, 600V L-G,
Nominal Discharge Current
(UL1449 3rd Edition _ 3,000A
Electrical Measurements
RMS Voltage ______ 1% precision
RMS Current ______ 1% precision
Power___________ 2% precision
Cumulative Energy__ 2% precision
AGENCY APPROVALS
C CSA US Certified: UL1449 3rd Edition
(Type 3 SPD), CSA C22.2 No. 42
UL 1449 Voltage Protection Rating:
400V L-N, 600V L-G, 500V N-G
C US
Cover can be removed & painted to match color of wall. The cover only can be painted. Do not paint the sides, top or bottom of the unit or
Warranty will be voided.
RF / ZigBee ®
ZigBee®/802.15.4 Radio
2.405-2.475 GHz, unlicensed ISM band
3dBm transmitter output
-99dBm receiver sensitivity
General
Weight__________ 0.7lb
Dimensions_______ 3.25 in. W X 1.625 in.
D X 5.25 in. H
ZigBee is a registered trademark of ZigBee Alliance, Inc.
WARRANTY POLICIES
Product Warranty: Limited 3 Year Warranty
Connected Equipment Protection Policy:
Limited $100,000
Connected Equipment Policy www.panamax.com www.mybluebolt.com
INSTALLATION INSTRUCTIONS MD2-ZB
POWER STATUS INDICATOR LIGHTS
Outlet 1
Network
Connection
Status
OUTLET 1
Left side
Ground Pin Out
PUSH BUTTONS
For Outlet’s Power ON/OFF and Network Connection
INDICATOR
LIGHTS
Outlet 2
Wiring Fault
OUTLET 2
Right side.
Ground Pin
Down
REMOVABLE COVER
FACEPLATE
Finger Indent to
Pull Off Cover.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
( 1) This device may not cause harmful interference, and
( 2) This device must accept any interference received,
including interference that may cause undesired operation.
MD2-ZB
This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications of Part 15 of FCC rules. These specifications are designed to provide reasonable protection against such interference win a residential installation.
However, there is no guarantee that interference will not occur in a particular installation.
In accordance with FCC 15.21, changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
www.panamax.com www.mybluebolt.com
DIN-00019-B 11/12
INSTALLATION
1 .
Turn OFF the equipment that you are plugging into the MD2-ZB
3.
Plug your equipment into the AC outlets.
NETWORK DEMAND RESP.
OUTLET 1 OUTLET 2
2.
Plug MD2-ZB into the wall outlet. The red WIRING FAULT light indicates an improperly wired outlet that must be checked by a qualified electrician.
Blue B LT ®
NETWORK DEMAND RESP.
OUTLET 1 OUTLET 2
4.
Press the OUTLET 1 and/or OUTLET 2 buttons to switch power on the respective outlets.
MD2-ZB requires BB-ZB1 Gateway (sold separately).
NETWORK DEMAND RESP.
OUTLET 1 OUTLET 2
Blue B LT ®
5.
If the NETWORK / DEMAND
RESPONSE light is RED, the MD2-ZB is not connected to a ZigBee network.
Proceed to step 6, SETUP.
SETUP
6.
Verify that a BlueBOLT ® device (BB-ZB1 or another MD2-ZB) is powered on and within
100 ft. of that active BlueBOLT ® device.
7.
Through the BlueBOLT ® interface, enable JOINING. Refer to the user manual for BB-ZB1 for detailed instructions.
NETWORK DEMAND RESP.
OUTLET 1 OUTLET 2
8.
On MD2-ZB, press and hold the
OUTLET 1 and OUTLET 2 buttons simultaneously until the NETWORK / DEMAND
RESPONSE light blips / blinks / flashes, approximately 4 seconds. The NETWORK/
DEMAND / RESPONSE light will turn
GREEN once it has joined the network.
BB-ZB1
Blue B LT
®
Blue
B LT ®
100 ft. Maximum 100 ft. Max.
100 ft. Maximum
MD2-ZB
MD2-ZB
Multiple MD2-ZB units can be installed within 100 ft. from an active device (BB-ZB1 or another active MD2-ZB).
Blue
B LT ®
MD2-ZB www.panamax.com www.mybluebolt.com
advertisement
Related manuals
advertisement