Delta 28-682 Instruction manual

Add to my manuals
20 Pages

advertisement

Delta 28-682 Instruction manual | Manualzz

18" Band Saw

(Model 28-682)

PART NO. 911988 - 07-28-04

Copyright © 2004 Delta Machinery

To learn more about DELTA MACHINERY visit our website at: www.deltamachinery.com.

For Parts, Service, Warranty or other Assistance, please call

1-800-223-7278 (

In Canada call

1-800-463-3582).

TABLE OF CONTENTS

IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

SAFETY GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

ADDITIONAL SPECIFIC SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

CARTON CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

SERVICE CENTER LOCATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .back cover

IMPORTANT SAFETY INSTRUCTIONS

Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury.

Improper operation, maintenance or modification of tools or equipment could result in serious injury and property damage. There are certain applications for which tools and equipment are designed. Delta Machinery strongly recommends that this product NOT be modified and/or used for any application other than for which it was designed.

If you have any questions relative to its application DO NOT use the product until you have written Delta Machinery and we have advised you.

Online contact form at www.deltamachinery.com

Postal Mail: Technical Service Manager

Delta Machinery

4825 Highway 45 North

Jackson, TN 38305

Information regarding the safe and proper operation of this tool is available from the following sources:

Power Tool Institute

1300 Sumner Avenue, Cleveland, OH 44115-2851 www.powertoolinstitute.org

National Safety Council

1121 Spring Lake Drive, Itasca, IL 60143-3201

American National Standards Institute, 25 West 43rd Street, 4 floor, New York, NY 10036 www.ansi.org

ANSI 01.1Safety Requirements for Woodworking Machines, and the U.S. Department of Labor regulations www.osha.gov

SAVE THESE INSTRUCTIONS!

2

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual. The information it contains relates to protecting YOUR

SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information.

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may result in property damage.

CALIFORNIA PROPOSITION 65

SOME DUST CREATED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHER

CONSTRUCTION ACTIVITIES contains chemicals known to cause cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

· lead from lead-based paints,

· crystalline silica from bricks and cement and other masonry products, and

· arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, always wear MSHA/NIOSH approved, properly fitting face mask or respirator when using such tools.

3

GENERAL SAFETY RULES

READ AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFORE

USING THIS EQUIPMENT. Failure to follow all instructions listed below, may result in electric shock, fire, and/or serious personal injury or property damage.

IMPORTANT SAFETY INSTRUCTIONS

1.

FOR YOUR OWN SAFETY, READ THE INSTRUCTION

MANUAL BEFORE OPERATING THE MACHINE.

Learning the machine’s application, limitations, and specific hazards will greatly minimize the possibility of accidents and injury.

2.

WEAR EYE PROTECTION. ALWAYS USE SAFETY

GLASSES. Also use face or dust mask if cutting operation is dusty. Everyday eyeglasses are NOT safety glasses. USE CERTIFIED SAFETY EQUIPMENT. Eye protection equipment should comply with ANSI Z87.1

standards, hearing equipment should comply with

ANSI S3.19 standards, and dust mask protection should comply with MSHA/NIOSH certified respirator standards. Splinters, air-borne debris, and dust can cause irritation, injury, and/or illness.

3.

WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Non-slip footwear is recommended. Wear protective hair covering to contain long hair.

4.

DO NOT USE THE MACHINE IN A DANGEROUS

ENVIRONMENT. The use of power tools in damp or wet locations or in rain can cause shock or electrocution. Keep your work area well-lit to prevent tripping or placing arms, hands, and fingers in danger.

5.

MAINTAIN ALL TOOLS AND MACHINES IN PEAK

CONDITION. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. Poorly maintained tools and machines can further damage the tool or machine and/or cause injury.

6.

CHECK FOR DAMAGED PARTS. Before using the machine, check for any damaged parts. Check for alignment of moving parts, binding of moving parts, breakage of parts, and any other conditions that may affect its operation. A guard or any other part that is damaged should be properly repaired or replaced.

Damaged parts can cause further damage to the machine and/or injury.

7.

KEEP THE WORK AREA CLEAN. Cluttered areas and benches invite accidents.

8.

KEEP CHILDREN AND VISITORS AWAY. Your shop is a potentially dangerous environment. Children and visitors can be injured.

9.

REDUCE THE RISK OF UNINTENTIONAL STARTING.

Make sure that the switch is in the “OFF” position before plugging in the power cord. In the event of a power failure, move the switch to the “OFF” position.

An accidental start-up can cause injury.

10. USE THE GUARDS. Check to see that all guards are in place, secured, and working correctly to prevent injury.

11. REMOVE ADJUSTING KEYS AND WRENCHES

BEFORE STARTING THE MACHINE. Tools, scrap pieces, and other debris can be thrown at high speed, causing injury.

12. USE THE RIGHT MACHINE. Don’t force a machine or an attachment to do a job for which it was not designed. Damage to the machine and/or injury may result.

13. USE RECOMMENDED ACCESSORIES. The use of accessories and attachments not recommended by

Delta may cause damage to the machine or injury to the user.

14. USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. See the Extension Cord Chart for the correct size depending on the cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

15. SECURE THE WORKPIECE. Use clamps or a vise to hold the workpiece when practical. Loss of control of a workpiece can cause injury.

16. FEED THE WORKPIECE AGAINST THE DIRECTION OF

THE ROTATION OF THE BLADE, CUTTER, OR ABRASIVE

SURFACE. Feeding it from the other direction will cause the workpiece to be thrown out at high speed.

17. DON’T FORCE THE WORKPIECE ON THE MACHINE.

Damage to the machine and/or injury may result.

18. DON’T OVERREACH. Loss of balance can make you fall into a working machine, causing injury.

19. NEVER STAND ON THE MACHINE. Injury could occur if the tool tips, or if you accidentally contact the cutting tool.

20. NEVER LEAVE THE MACHINE RUNNING UNATTENDED.

TURN THE POWER OFF. Don’t leave the machine until it comes to a complete stop. A child or visitor could be injured.

21. TURN THE MACHINE “OFF”, AND DISCONNECT THE

MACHINE FROM THE POWER SOURCE before installing or removing accessories, before adjusting or changing set-ups, or when making repairs. An accidental start-up can cause injury.

22. MAKE YOUR WORKSHOP CHILDPROOF WITH

PADLOCKS, MASTER SWITCHES, OR BY

REMOVING STARTER KEYS. The accidental start-up of a machine by a child or visitor could cause injury.

23. STAY ALERT, WATCH WHAT YOU ARE DOING, AND

USE COMMON SENSE. DO NOT USE THE

MACHINE WHEN YOU ARE TIRED OR UNDER THE

INFLUENCE OF DRUGS, ALCOHOL, OR

MEDICATION. A moment of inattention while operating power tools may result in injury.

24. TAKE PRECAUTIONS AGAINST DUST INHALATION.

The dust generated by certain woods and wood products can be injurious to your health. Always operate machinery in well-ventilated areas, and provide for proper dust removal. Use wood dust collection systems whenever possible.

4

ADDITIONAL SAFETY RULES FOR BAND SAWS

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.

1.

DO NOT OPERATE THIS MACHINE UNTIL it is

2.

OBTAIN ADVICE from your supervisor,

3.

4.

5.

assembled and installed according to the instructions.

instructor, or another qualified person if you are not familiar with the operation of this tool.

FOLLOW ALL WIRING CODES and recommended electrical connections.

USE THE GUARDS WHENEVER POSSIBLE. Check to see that they are in place, properly adjusted, secured, and working correctly.

USE PROPER BLADE SIZE and type.

6.

ADJUST THE UPPER BLADE GUIDE so that it is about 1/8" above the workpiece.

7.

PROPERLY ADJUST the blade tension, tracking, blade guides, and blade support bearings.

8.

KEEP ARMS, HANDS, AND FINGERS away from the blade.

9.

AVOID AWKWARD OPERATIONS and hand positions where a sudden slip could cause a hand to move into the blade.

10. NEVER START THE MACHINE before clearing the table of all objects (tools, scrap pieces, etc.).

11. NEVER START THE MACHINE with the workpiece against the blade.

12. HOLD WORKPIECE FIRMLY against the table. DO

NOT attempt to saw a workpiece that does not have a flat surface against the table.

13. HOLD WORKPIECE FIRMLY and feed into blade at a moderate speed.

14. NEVER REACH UNDER THE TABLE while the machine is running.

15. TURN THE MACHINE “OFF” to back out of an uncompleted or jammed cut.

16. MAKE “RELIEF” CUTS prior to cutting long curves.

17. TURN THE MACHINE “OFF” and wait for the blade to stop prior to cleaning the blade area, removing debris near the blade, removing or securing workpiece, or changing the angle of the table. A coasting blade can be dangerous.

18. NEVER PERFORM LAYOUT, ASSEMBLY, or setup work on the table/work area when the machine is running.

19. TURN THE MACHINE “OFF” AND DISCONNECT

THE MACHINE from the power source before installing or removing accessories, before adjusting or changing set-ups, or when making repairs.

20. TURN THE MACHINE “OFF”, disconnect the machine from the power source, and clean the table/work area before leaving the machine. LOCK

THE SWITCH IN THE “OFF” POSITION to prevent unauthorized use.

21. ADDITIONAL INFORMATION regarding the safe and proper operation of power tools (i.e. a safety video) is available from the Power Tool Institute,

1300 Sumner Avenue, Cleveland, OH 44115-2851

(www.powertoolinstitute.com). Information is also available from the National Safety Council, 1121

Spring Lake Drive, Itasca, IL 60143-3201. Please refer to the American National Standards Institute

ANSI 01.1 Safety Requirements for Woodworking

Machines and the U.S. Department of Labor OSHA

1910.213 Regulations.

SAVE THESE INSTRUCTIONS.

Refer to them often and use them to instruct others.

5

POWER CONNECTIONS

A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the machine to the power line, make sure the switch (s) is in the “OFF” position and be sure that the electric current is of the same characteristics as indicated on the machine. All line connections should make good contact. Running on low voltage will damage the machine.

DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.

MOTOR SPECIFICATIONS

Your machine is wired for 230 volt, 60 HZ alternating current. Before connecting the machine to the power source, make sure the switch is in the “OFF” position.

GROUNDING INSTRUCTIONS

THIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM

ELECTRIC SHOCK.

1. All grounded, cord-connected machines:

In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This machine is equipped with an electric cord having an equipmentgrounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Do not modify the plug provided - if it will not fit the outlet, have the proper outlet installed by a qualified electrician.

Improper connection of the equipment-grounding conductor can result in risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipmentgrounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal.

Check with a qualified electrician or service personnel if t h e g r o u n d i n g i n s t r u c t i o n s a r e n o t c o m p l e t e l y understood, or if in doubt as to whether the machine is properly grounded.

Use only 3-wire extension cords that have 3-prong grounding type plugs and matching 3-conductor receptacles that accept the machine’s plug, as shown in

Fig. A.

Repair or replace damaged or worn cord immediately.

2. Grounded, cord-connected machines intended for use on a supply circuit having a nominal rating less than 150 volts:

If the machine is intended for use on a circuit that has an outlet that looks like the one illustrated in Fig. A, the machine will have a grounding plug that looks like the plug illustrated in Fig. A. A temporary adapter, which looks like the adapter illustrated in Fig. B, may be used to connect this plug to a matching 2-conductor receptacle as shown in Fig. B if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet can be installed by a qualified electrician.

The green-colored rigid ear, lug, and the like, extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. Whenever the adapter is used, it must be held in place with a metal screw.

NOTE: In Canada, the use of a temporary adapter is not permitted by the Canadian Electric Code.

IN ALL CASES, MAKE CERTAIN THE

R E C E P TA C L E I N Q U E S T I O N I S P R O P E R LY

G R O U N D E D . I F Y O U A R E N O T S U R E H AV E A

QUALIFIED ELECTRICIAN CHECK THE RECEPTACLE.

GROUNDED OUTLET BOX

CURRENT

CARRYING

PRONGS

GROUNDED OUTLET BOX

GROUNDING

MEANS

ADAPTER

GROUNDING BLADE

IS LONGEST OF THE 3 BLADES

Fig. A Fig. B

3. Grounded, cord-connected machines intended for use on a supply circuit having a nominal rating between 150 - 250 volts, inclusive:

If the machine is intended for use on a circuit that has an outlet that looks like the one illustrated in Fig. C, the machine will have a grounding plug that looks like the plug illustrated in Fig. C. Make sure the machine is connected to an outlet having the same configuration as the plug. No adapter is available or should be used with this machine. If the machine must be re-connected for use on a different type of electric circuit, the reconnection should be made by qualified service personnel; and after re-connection, the machine should comply with all local codes and ordinances.

GROUNDED OUTLET BOX

CURRENT

CARRYING

PRONGS

GROUNDING BLADE

IS LONGEST OF THE 3 BLADES

Fig. C

EXTENSION CORDS

Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord which has a 3-prong grounding type plug and matching receptacle which will accept the machine’s plug. When using an extension cord, be sure to use one heavy enough to carry the current of the machine. An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. Fig. D-1 or D-2, shows the correct gauge to use depending on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

MINIMUM GAUGE EXTENSION CORD

RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES

Ampere

Rating Volts

Total Length of Cord in Feet

Gauge of

Extension Cord

0-6

0-6

0-6

0-6

6-10

6-10

6-10

6-10

10-12

10-12

10-12

10-12

12-16

12-16

12-16

120

120

120

120

120

120

120

120

120

120

120

120

120

120

120 up to 25

25-50

50-100

100-150 up to 25

25-50

50-100

100-150

18 AWG

16 AWG

16 AWG

14 AWG

18 AWG

16 AWG

14 AWG

12 AWG up to 25

25-50

50-100

100-150

16 AWG

16 AWG

14 AWG

12 AWG up to 25

25-50

14 AWG

12 AWG

GREATER THAN 50 FEET NOT RECOMMENDED

Fig. D-1

MINIMUM GAUGE EXTENSION CORD

RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES

Ampere

Rating Volts

Total Length of Cord in Feet

Gauge of

Extension Cord

0-6

0-6

0-6

0-6

6-10

6-10

6-10

6-10

10-12

10-12

10-12

10-12

12-16

12-16

12-16

240

240

240

240

240

240

240

240

240

240

240

240

240

240

240 up to 50

50-100

100-200

200-300 up to 50

50-100

100-200

200-300

18 AWG

16 AWG

16 AWG

14 AWG

18 AWG

16 AWG

14 AWG

12 AWG up to 50

50-100

100-200

200-300

16 AWG

16 AWG

14 AWG

12 AWG up to 50

50-100

14 AWG

12 AWG

GREATER THAN 100 FEET NOT RECOMMENDED

Fig. D-2

7

FUNCTIONAL DESCRIPTION

FOREWORD

Delta Model 28-682 is an 18" Wood Cutting Band Saw. This machine has speeds of 2300 and 3250 SFPM (surface feet per minute). Its blade to frame capacity is 17 1 /

2

" and its height under guide capacity is 12". The band saw has a quick blade tensioning mechanism for ease of changing blades. The Delta Model 28-682 has a large 17 3 /

4

"x18" cast iron table that can be tilted 48 degrees to the right and 10 degrees to the left. The band saw also comes with a 4" O.D. dust port for connecting the band saw to a dust collector.

NOTICE: THE PHOTO ON THE MANUAL COVER ILLUSTRATES THE

CURRENT PRODUCTION MODEL. ALL OTHER ILLUSTRATIONS CONTAINED

IN THE MANUAL ARE REPRESENTATIVE ONLY AND MAY NOT DEPICT THE

ACTUAL COLOR, LABELING OR ACCESSORIES AND ARE INTENDED TO

ILLUSTRATE TECHNIQUE ONLY.

CARTON CONTENTS

2

1

3

5

4

6

12

7

15

10

8

9

11

16

1.

Band Saw

2.

Table

3.

3mm T-Handle Wrench

4.

6mm Hex Wrench

5.

5mm Hex Wrench

6.

3mm Hex Wrench

7.

Table Insert

8.

Trunnion Lock Knob

9.

Trunnion Lock Knob

13 14 17

Fig. 2

10. Table Extension Lock Knob (2)

11. Fence

12. Resaw Guide

13. Front Fence Rail

14. Rear Fence Rail

15. 1/4-20 x 1-1/2" Socket Head Screw (2)

16. 1/4-20 x 1" Socket Head Cap Screw (2)

17. Spacer (2)

8

UNPACKING AND CLEANING

Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating from all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene. (Do not use acetone, gasoline or lacquer thinner for this purpose.) After cleaning, cover the unpainted surfaces with a good quality household floor paste wax.

B

A

1.

Remove the four bolts (A) Fig. 1 (three of which are shown) that attach the saw (B) to the shipping skid.

A

2.

Save the four bolts to permanently mount the saw to a supporting surface.

Fig. 1

THIS MACHINE IS HEAVY AND CAN TILT EASILY. USE FOUR OR MORE PEOPLE TO SLIDE THE

MACHINE OFF OF THE SHIPPING SKID.

ASSEMBLY TOOLS REQUIRED

* 5mm Hex Wrench (supplied)

* Phillips head screwdriver (not supplied)

ASSEMBLY

ASSEMBLY TIME ESTIMATE - 2 to 4 hours

FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL

THE MACHINE IS COMPLETELY ASSEMBLED, AND YOU READ AND UNDERSTAND THE ENTIRE

INSTRUCTION MANUAL.

ON/OFF SWITCH

1.

Remove the two screws (A) Fig. 3 on the cover of the on/off switch, and remove the front cover.

2.

Align the two holes of the On/Off switch with the two holes (B) Fig. 4 on the front of the saw.

3.

Thread the two screws (located loose in the switch box) into the two holes in the front of the saw and tighten securely.

4.

Replace the front cover of the On/Off switch that was removed in STEP 1.

A

B

Fig. 3

A

9

Fig. 4

TABLE

1.

Remove the table pin (A) Fig. 5.

2.

Align the blade with the table slot (B) Fig. 5. Slide the table until the blade has reached the center cutout (C) Fig.

5, then rotate the table 90 degrees toward the front of the machine.

NOTE: Make sure that the table slot (B) Fig. 6 is facing toward the right of the machine.

3.

Align the two table studs (A) Fig. 6, in the bottom of the table, with the two holes in the trunnion assemblies.

4.

Thread the trunnion lock knob (D) Fig. 7 onto the table stud. Repeat this process for the other table stud.

5.

Pull out on the table extension (G) Fig. 8.

6.

Remove the two screws, flat washers, and lockwashers (H) Fig. 8, from the table using the 5mm hex wrench.

8.

Loosen the table lock knob (J) Fig. 8.

9.

Align the two holes (K) Fig. 8, on the table trunnion (L), with the two holes (H) on the table.

10. Replace the two screws, flat washers, and lockwashers (H) Fig. 8A, that were removed in STEP 6 to attach the trunnion to the table. Tighten using the 5mm hex wrench

12. Thread the two table extension lock knobs (N) Fig. 8A, into the bottom of the table.

11. Replace the table pin that was removed in STEP 1.

B

C

Fig. 5

A

B

L

A

Fig. 6

J

Fig. 8

H

K

A

G

10

N

D

Fig. 7

D

H

N

Fig. 8A

FENCE

1. Align the two holes (A) Fig. 9 in the front fence rail with the two holes (B) in the front of the table.

NOTE: Make sure that the scale on the front fence rail is facing upward.

2. Insert a 1/4-20 x 1-1/2" socket-head cap screw through one of the holes (A) Fig. 9 hole in the front fence rail. Place a spacer on the screw between the front fence rail and the table. Thread the screw into the front of the table. Repeat for the other hole (A) in the front fence rail. Tighten the two screws securely using the 5mm hex wrench.

3. Align the two holes (C) Fig. 9A in the rear fence rail with the two holes (D) in the rear of the table.

4. Insert a 1/4-20 x 1" socket head cap screw through one of the holes (C) in the rear fence rail. Thread the screw into the matching hole in the rear of the table. Repeat for the other hole in the rear fence guide and the table. Tighten the two screws securely using the 5mm hex wrench.

5. Loosen the fence lock knob (E) Fig. 10 and position the opening of the fence bracket over the front guide rail. Slide the fence on the fence guide rail (Fig. 11).

NOTE: The fence can be attached to either side of the blade.

6. Tighten fence lock knob (E) Fig. 11.

B D

C

A

Fig. 9 Fig. 9A

E

B

Fig. 10

A

E

Fig. 11

A

A

C

Fig. 12 Fig. 13

TABLE INSERT

Place the table insert (A) Fig. 12 in the table cutout. NOTE: A tab (B) is provided on the insert that engages with the notch (C) in the table opening.

FENCE EXTENSION

Loosen the two knobs (A) Fig. 13 to extend the table.

11

OPERATION

OPERATIONAL CONTROLS AND ADJUSTMENTS

STARTING AND STOPPING SAW

The power switch is located on the left side of the machine. To turn the machine “ON”, push the green start button (A)

Fig. 14. To turn the machine “OFF”, push the red stop button (B).

LOCKING SWITCH IN THE “OFF” POSITION

IMPORTANT: When the tool is not in use, the switch should be locked in the “OFF” position to prevent unauthorized use, using a padlock (C) Fig. 15 with a 3/16" diameter shackle.

A

B

C

Fig. 14

TILTING THE TABLE

Fig. 15

DISCONNECT MACHINE FROM POWER SOURCE.

The table can be tilted 47 degrees to the right and 5 degrees to the left. To tilt the table to the right, loosen the two clamp handles (one shown at (A) Fig. 16), and bevel lock handle (B) Fig. 16A. Move the stop tab (C) inset out of the way. Tilt the table to the desired angle on the scale (D) Figs. 16, and tighten the two locking handles (A) Fig. 16 and the bevel lock handle (B) Fig. 16A.

D

B

C

A

Fig. 16

ADJUSTING BLADE TENSION

To prevent weakening of the blade, the machine is shipped with the blade under slight tension.

To adjust:

1.

Locate the blade tension lever (A) Fig. 17 on top of the machine.

2.

Locate the Tension Scale (B) Fig.17 on the back side of the upper wheel guard.

3.

Open the upper and lower doors to see that the blade is situated correctly on both wheels.

12

Fig. 16A

A

B

Fig. 17

4.

Raise the blade tension lever to the “up” position and turn it clockwise to increase tension or counterclockwise to relieve the tension.

5.

After the first turn, lower the blade tension lever and check the tension scale. If the tension is still not correct, repeat the procedure.

The tension scale is correct for standard blades used on average work. Although you may rely on the feel or tone of the blade, Delta recommends that you use the tension scale to avoid blade breakage by applying too much or too little tension.

NOTE: When the machine is not in use, relax the tension on the blade by lifting the blade tension lever to the “UP” position. Remember to lower the blade tension lever before using the machine again.

Fig. 18

TRACKING THE BLADE

For accurate work and maximum blade life, center the blade on the upper wheel. With proper tracking adjustment, the blade will run steadily in the same line. Before adjusting the tracking, move the upper and lower blade guides and blade support bearings away from the sides and back of the blade (See “ADJUSTING UPPER BLADE GUIDES AND BLADE

SUPPORT BEARING” and “ADJUSTING LOWER BLADE GUIDES AND BLADE SUPPORT BEARING” in this manual. Also, tension the blade properly by following the instructions under “ADJUSTING BLADE TENSION”.

DISCONNECT MACHINE FROM POWER SOURCE.

B

A

Fig. 19 Fig. 20

To adjust:

1.

Rotate the upper wheel (A) Fig. 19 forward by hand and turn the tracking adjustment hand knobs (B) Fig. 20 until the blade travels in the center of the upper wheel’s tire. Be sure the knobs (B) Fig. 20 are always turned equal amounts.

NOTE: Before turning the hand knobs (B) Fig. 20, loosen the locknuts located under the knobs.

2.

Connect the machine to the power source and turn the switch “ON” and “OFF” to be certain that proper tracking is maintained.

To avoid possible injury and/or damage to the blade, do not make the initial tracking adjustment while the machine is under power. The blade may run off the wheel instantly at high speed.

Adjust the tracking knobs (B) Fig. 20 only a fraction of a turn at a time. Each blade has its own tendencies, especially after welding or brazing. Repeat the blade tracking adjustment each time a new or repaired blade is installed, regardless of prior adjustments.

3.

Make any necessary final adjustments at operating speed and tighten the locknuts located under the knobs (B)

Fig. 20.

13

CHANGING SPEEDS

DISCONNECT MACHINE FROM POWER SOURCE.

1.

Open the bottom access door (See D, Fig. 26).

2.

Locate and loosen motor release handle (C) Fig. 20A inset by turning it counter-clockwise.

3.

Lift up motor assembly and move belt (A) to desired groove on motor pulley (B). Move belt to outer groove

(D) for 2300 SFPM, or to inner groove (E) for 3250

SFPM.

4.

Push down on motor assembly and then turn motor release handle (C) clockwise to tighten belt.

5.

Close the bottom access door.

C

E

D

B

A

Fig. 20A

ADJUSTING UPPER BLADE GUIDE ASSEMBLY

Set the upper blade guide assembly (A) Fig. 21 as close as possible to the top surface of the workpiece by loosening the lock knob (D) and turning the handle (B) until the guide assembly is in the correct position. A scale (C) Fig. 21 in increments of 1/8" is located above the assembly.

B

C

D

G

C

E

B

A

D

F

Fig. 21 Fig. 22

ADJUSTING UPPER BLADE GUIDE AND BLADE SUPPORT BEARING

DISCONNECT MACHINE FROM POWER SOURCE.

Adjust the blade support bearing (B) Fig. 22 so that it is within 1/64” of, but not touching the back of the saw blade when the blade is at rest. To adjust, loosen the indexable locking lever (C) and slide the bracket in or out until the adjustment is correct.

Tighten the lever (C). Adjust the blade guide bearings (D) by loosening the screw (F) and rotating the bearing on the shaft (G) so that the bearings touch, but do not pinch the blade. Tighten the screw (F).Position the front edge of the guide bearings just behind the “gullets” of the saw teeth. To adjust, loosen indexable locking lever (E) and slide the bearing assembly in or out until the adjustment is correct. Tighten the lever.

ADJUSTING LOWER BLADE GUIDE AND BLADE SUPPORT BEARING

DISCONNECT MACHINE FROM POWER E

SOURCE.

F

G

C

D

The lower bearing adjustments are similar to the upper bearing adjustments. Adjust the blade support bearing (A) Fig 23 so that it is within 1/64” of, but not touching the back of the saw blade when the blade is at rest. To adjust, loosen hex screw (B) and slide the bracket in or out until the adjustment is correct. Tighten the screw. Adjust the blade guide bearings (C,G) by loosening the screw (E) and rotating the bearing on the shaft (F) so that the bearings touch, but do not pinch the blade. To gain access the back bearing (G), you will need to remove the table insert and tilt the table to the right. Return table to level position. The front edge

A

B

Fig. 23 of the guide bearings (C) should be just behind the “gullets” of the saw teeth. To adjust, loosen the hex screw (D) and slide the bearing assembly into place. Tighten the hex screw (D).

14

ADJUSTING THE TABLE POSITIVE STOP

DISCONNECT MACHINE FROM POWER

SOURCE.

This machine is equipped with a positive stop that allows the table to be rapidly positioned at 90 degrees to the blade after the table has been tilted.

To check and adjust:

1.

Place the table in the 90 degree position and lock it in place.

2.

Place a square (A) Fig. 24 on the table with one end against the blade to check for 90 degrees.

3.

If an adjustment is necessary, loosen the locknut (B)

Fig. 25 and tighten or loosen the adjusting screw (C) until the head of the screw (C) contacts the bottom of the table when the table is 90 degrees to the blade.

4.

Tighten the locknut (B).

C

B

CHANGING BLADES

NOTE: This machine uses blades that are 136" in length.

To change blades:

DISCONNECT MACHINE FROM POWER

SOURCE.

1.

Turn the knobs (A and B) Fig. 26 clockwise to open both the upper and lower doors.

2.

Move the Tension Lever (C) to the up position.

3.

Remove the table insert (A) Fig. 27 and the table pin

(B).

4.

Take the blade off both the upper and lower wheels.

5.

Turn the blade so that it slides out of the table through the table slot.

6.

Reverse the procedure to install a new blade.

7.

Adjust the blade tension, track the blade, and adjust both upper and lower blade guides and blade support bearings.

D

A

B

A

Fig. 24

Fig. 25

C

A

B

Fig. 27 Fig. 26

15

A

A

Fig. 28 Fig. 28A

ADJUSTING RESAW GAUGE

The resaw gauge (A) attaches to the fence (Fig. 28). Slide it along the fence slot until the edge is slightly in front of the blade teeth. Use this gauge for resawing operations and for cutting warped workpieces.

ADJUSTING BELT TENSION

If it becomes necessary to adjust the belt tension on the machine, turn the motor release handle (A) Fig. 28A counterclockwise. Lower or raise the motor, and when adjustment is complete, tighten the motor release handle (A).

DUST CHUTE

Two dust chutes (A) Fig. 29 are supplied with your machine and can easily be connected to a dust collection system. The O.D. of the dust chutes is 4" in diameter.

A

Fig. 29

MACHINE USE

Before starting the machine, insure that all adjustments are properly made and the guards are in place. Turn the upper wheel by hand to make sure that everything is correct BEFORE turning on the power.

Keep the top guide within 1/8" of the work piece at all times. Do not force the material against the blade. Light pressure on the work piece will produce a smoother cut, and prevent excess friction, and heating of the blade.

KEEP THE SAW BLADE SHARP. Very little forward pressure is required for normal cutting. Keep the workpiece moving at a slow and consistent rate against the blade to ensure a smooth and accurate cut.

Avoid twisting the blade, by trying not to turn sharp corners. Remember, you must saw around corners.

CUTTING CURVES

When cutting curves, turn the stock carefully so that the blade follows without twisting. If a curve is so abrupt that it is necessary to repeatedly back up and cut a new kerf, a narrower blade, a blade with more set, or additional relief cuts may be necessary to allow the blade to cut more efficiently. The more set a blade has, the easier it will allow the stock to be turned, but the cut is usually rougher.

When withdrawing the piece being cut, changing the cut, or for any other reason, be careful not to accidentally draw the blade off the wheels. In most cases, it is easier and safer to turn the stock and saw out through the waste material, rather than try to withdraw the stock from the blade.

16

BAND SAW BLADES

A band saw blade is a delicate piece of steel that is subjected to tremendous strain. You can obtain long use from a band saw blade if you use it properly. Be sure you use blades of the proper thickness, width and temper for the various types of material and cuts.

Always use the widest blade possible. Use narrow blades only for sawing small, abrupt curves and for fine, delicate widths of 5/8", 3/4", 1", and 1

1

/4" for 136” length blades.

Any one of a number of conditions may cause a band saw blade to break. Blade breakage is, in some cases, unavoidable, being the natural result of the peculiar stresses to which blades are subjected. Blades will break often due to avoidable causes, such as the lack of care to the blade or the blade not being properly adjusted to the band saw. The most common causes of blade breakage are:

(1) faulty alignments and adjustments of the guides.

(2)

(3) forcing or twisting a wide blade around a curve of short radius.

feeding the work piece too fast into the blade.

(4)

(5)

(6)

(7)

(8) dullness of the teeth, or absence of sufficient set.

improperly tensioned blade.

top guide set too high above the work piece being cut.

using a blade with a lumpy or improperly finished braze or weld.

continuous running of the saw blade when not cutting.

Use blades that are 136" in length on this machine.

Always use a sharp blade. Keep it free of gum and pitch. Clean frequently with a stiff fiber brush.

Narrow blades are best suited for cutting small circles or curves while the wider blades are best suited for straight cutting such as ripping.

A new blade, in most cases, will perform better and last longer than a re-sharpened blade.

Insure that the blade guides are adjusted properly.

Do not force or twist the blade around a curve or a very short radius.

Feed the workpiece through the blade at a consistent rate, allow the blade to do the cutting – do not feed the work piece too fast.

Do not apply excessive tension to the blade. The tension is only necessary to drive the blade without slipping on the wheels. Narrow blades require less tension than wider blades.

TROUBLESHOOTING

For assistance with your machine, visit our website at www.deltamachinery.com for a list of service centers or call the DELTA Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582). Some common problems are addressed below:

Trouble: SAW WILL NOT START.

Probable Cause

1. Saw not plugged in.

2. Fuse blown or circuit breaker tripped.

3. Cord damaged.

Remedy

1. Plug in saw.

2. Replace fuse or reset circuit breaker.

3. Have cord replaced.

Trouble: BREAKER KICKS OUT FREQUENTLY.

Probable Cause

1. Extension cord too light or too long.

2. Feeding stock too fast.

3. Blade in poor condition (dull, warped, gummed).

4. Low voltage supply.

Remedy

1. Replace with adequate size cord.

2. Feed stock more slowly.

3. Clean or replace blade.

4. Contact an electrician.

17

Trouble: BAND SAW VIBRATES EXCESSIVELY.

Probable Cause

1. Machine not mounted securely to stand.

2. Stand on uneven surface.

3. Worn belt.

4. Pulley not aligned.

5. Motor not fastened securely.

Trouble: BAND SAW DOES NOT COME UP TO SPEED.

Probable Cause

1. Low voltage due to improper extension cord size.

2. Low voltage.

Trouble: BLADES BREAK.

Probable Cause

1. Blade not tensioned properly.

2. Blade guides improperly adjusted.

3. Blade support bearing improperly adjusted.

4. Blade wheel tracking adjustment improperly set.

5. Bad weld on blade.

6. Worn tires.

7. Forcing wide blade around short radius.

8. Dull blade or insufficient set.

9. Upper blade guide set too high.

10. Continuous running of machine when not actually cutting.

Remedy

1. Tighten all mounting hardware.

2. Reposition on flat level surface.

3. Replace belt.

4. Adjust pulleys.

5. Tighten all mounting hardware.

Remedy

1. Replace with adequate size cord.

2. Contact an electrician.

Remedy

1. Adjust blade tension.

2. Check and adjust blade guides.

3. Adjust blade support bearing.

4. Check and adjust blade tracking.

5. Replace the blade.

6. Replace tires.

7. Change to a narrower blade.

8. Replace blade.

9. Set upper blade guide within 1/8" of workpiece.

10. Turn off machine when not performing cutting operation.

Trouble: BLADE WILL NOT TRACK.

Probable Cause

1. Blade too loose

2. Upper wheel not properly adjusted.

3. Improperly adjusted blade support bearing.

Remedy

1. Adjust tension

2. Adjust upper wheel.

3. Adjust blade support bearing.

Trouble: CUT DOES NOT AGREE WITH SETTING ON THE TILT SCALE.

Probable Cause Remedy

1. Pointer out of adjustment 1. Adjust pointer.

Trouble: BLADE WILL NOT STAY ON WHEEL.

Probable Cause

1. Blade not tensioned properly.

2. Blade guides improperly adjusted.

3. Blade support bearing improperly adjusted.

4. Blade wheel not tracking properly.

5. Bad weld on blade.

6. Worn tires.

Trouble: BAND SAW MAKES UNSATISFACTORY CUTS.

Probable Cause

1. Blade not tensioned properly.

2. Blade guides improperly adjusted.

3. Blade support bearing improperly set.

4. Blade wheel not tracking properly.

5. Bad weld on blade.

6. Worn tires.

7. Incorrect blade for work being done.

8. Dull blade or insufficient set.

9. Upper blade guide set too high.

Remedy

1. Adjust blade tension.

2. Check and adjust blade guides.

3. Adjust blade support bearing.

4. Check and adjust blade tracking.

5. Replace the blade.

6. Replace tires.

Remedy

1. Adjust blade tension.

2. Check and adjust blade guides.

3. Adjust blade support bearing.

4. Check and adjust blade tracking.

5. Replace the blade.

6. Replace tires.

7. Change the blade.

8. Replace blade.

9. Set upper blade guide within 1/8" of work piece.

18

MAINTENANCE

KEEP MACHINE CLEAN

Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material.

LUBRICATION

Apply household floor paste wax to the machine table and extension table or other work surface weekly.

PROTECTING CAST IRON FROM RUST

Wear ANSI Z87.1 safety glasses while using compressed air.

FAILURE TO START

Should your machine fail to start, check to make sure the prongs on the cord plug are making good contact in the outlet. Also, check for blown fuses or open circuit breakers in the line.

To clean and protect cast iron tables from rust, you will need the following materials: 1 pushblock from a jointer,

1 sheet of medium Scotch-Brite™ Blending Hand Pad, 1 can of WD-40 ® , 1 can of degreaser, 1 can of TopCote ®

Aerosol. Apply the WD-40 and polish the table surface with the Scotch-Brite pad using the pushblock as a holddown. Degrease the table, then apply the TopCote ® accordingly.

SERVICE

PARTS, SERVICE OR WARRANTY ASSISTANCE

All Delta Machines and accessories are manufactured to high quality standards and are serviced by a network of Porter-Cable

Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional information regarding your Delta quality product or to obtain parts, service, warranty assistance, or the location of the nearest service outlet, please call 1-800-223-7278 (In Canada call 1-800-463-3582).

ACCESSORIES

A complete line of accessories is available from your Delta Supplier, Porter-Cable

• Delta Factory Service Centers, and Delta Authorized Service Stations. Please visit our Web Site

www.deltamachinery.com

for a catalog or for the name of your nearest supplier.

Since accessories other than those offered by Delta have not been tested with this product, use of such accessories could be hazardous. For safest operation, only

Delta recommended accessories should be used with this product.

WARRANTY

Two Year Limited New Product Warranty

Delta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, provided that the customer returns the product prepaid to a Delta factory service center or authorized service station with proof of purchase of the product within two years and provides Delta with reasonable opportunity to verify the alleged defect by inspection. For all refurbished Delta product, the warranty period is 180 days. Delta may require that electric motors be returned prepaid to a motor manufacturer’s authorized station for inspection and repair or replacement. Delta will not be responsible for any asserted defect which has resulted from normal wear, misuse, abuse or repair or alteration made or specifically authorized by anyone other than an authorized Delta service facility or representative. Under no circumstances will Delta be liable for incidental or consequential damages resulting from defective products. This warranty is Delta’s sole warranty and sets forth the customer’s exclusive remedy, with respect to defective products; all other warranties, express or implied, whether of merchantability, fitness for purpose, or otherwise, are expressly disclaimed by Delta.

19

PORTER-CABLE

DELTA SERVICE CENTERS

(CENTROS DE SERVICIO DE PORTER-CABLE

DELTA)

Parts and Repair Service for Porter-Cable

Delta Machinery are Available at These Locations

(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable

Delta)

ARIZONA

Tempe 85282 (Phoenix)

2400 West Southern Avenue

Suite 105

Phone: (602) 437-1200

Fax: (602) 437-2200

CALIFORNIA

Ontario 91761 (Los Angeles)

3949A East Guasti Road

Phone: (909) 390-5555

Fax: (909) 390-5554

San Diego 92111

7638 Clairemnot Blvd.

Phone: (858) 277-9595

Fax: (858) 277-9696

Tampa 33609

4538 W. Kennedy Boulevard

Phone: (813) 877-9585

Fax: (813) 289-7948

GEORGIA

Forest Park 30297 (Atlanta)

5442 Frontage Road,

Suite 112

Phone: (404) 608-0006

Fax: (404) 608-1123

ILLINOIS

Addison 60101 (Chicago)

400 South Rohlwing Rd.

Phone: (630) 424-8805

Fax: (630) 424-8895

MICHIGAN

Madison Heights 48071 (Detroit)

30475 Stephenson Highway

Phone: (248) 597-5000

Fax: (248) 597-5004

MINNESOTA

Minneapolis 55429

5522 Lakeland Avenue North

Phone: (763) 561-9080

Fax: (763) 561-0653

MISSOURI

North Kansas City 64116

1141 Swift Avenue

Phone: (816) 221-2070

Fax: (816) 221-2897

Cleveland 44125

8001 Sweet Valley Drive

Unit #19

Phone: (216) 447-9030

Fax: (216) 447-3097

OREGON

Portland 97230

4916 NE 122 nd Ave.

Phone: (503) 252-0107

Fax: (503) 252-2123

PENNSYLVANIA

Willow Grove 19090

(Philadelphia)

520 North York Road

Phone: (215) 658-1430

Fax: (215) 658-1433

San Leandro 94577 (Oakland)

3039 Teagarden Street

Phone: (510) 357-9762

Fax: (510) 357-7939

COLORADO

Arvada 80003 (Denver)

8175 Sheridan Blvd., Unit S

Phone: (303) 487-1809

Fax: (303) 487-1868

FLORIDA

Davie 33314 (Miami)

4343 South State Rd. 7 (441)

Unit #107

Phone: (954) 321-6635

Fax: (954) 321-6638

Woodridge 60517 (Chicago)

2033 West 75th Street

Phone: (630) 910-9200

Fax: (630) 910-0360

MARYLAND

Elkridge 21075 (Baltimore)

7397-102 Washington Blvd.

Phone: (410) 799-9394

Fax: (410) 799-9398

MASSACHUSETTS

Franklin 02038 (Boston)

Franklin Industrial Park

101E Constitution Blvd.

Phone: (508) 520-8802

Fax: (508) 528-8089

St. Louis 63119

7574 Watson Road

Phone: (314) 968-8950

Fax: (314) 968-2790

NEW YORK

Flushing 11365-1595 (N.Y.C.)

175-25 Horace Harding Expwy.

Phone: (718) 225-2040

Fax: (718) 423-9619

NORTH CAROLINA

Charlotte 28270

9129 Monroe Road, Suite 115

Phone: (704) 841-1176

Fax: (704) 708-4625

OHIO

Columbus 43214

4560 Indianola Avenue

Phone: (614) 263-0929

Fax: (614) 263-1238

TEXAS

Carrollton 75006 (Dallas)

1300 Interstate 35 N, Suite 112

Phone: (972) 446-2996

Fax: (972) 446-8157

Houston 77043

4321 Sam Houston Parkway,

West

Suite 180

Phone: (713) 983-9910

Fax: (713) 983-6645

WASHINGTON

Auburn 98001(Seattle)

3320 West Valley HWY, North

Building D, Suite 111

Phone: (253) 333-8353

Fax: (253) 333-9613

Authorized Service Stations are located in many large cities. Telephone 800-438-2486 or 731-541-6042 for assistance locating one.

Parts and accessories for Porter-Cable

·

Delta products should be obtained by contacting any Porter-Cable

·

Delta Distributor, Authorized

Service Center, or Porter-Cable

·

Delta Factory Service Center. If you do not have access to any of these, call 800-223-7278 and you will be directed to the nearest Porter-Cable

·

Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas grandes ciudades. Llame al 800-438-2486 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios para los productos Porter-Cable

·

Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable

·

Delta, Centro de Servicio Autorizado o Centro de Servicio de Fábrica Porter-Cable

·

Delta. Si no tiene acceso a ninguna de estas opciones, llame al

800-223-7278 y le dirigirán al Centro de Servicio de Fábrica Porter-Cable

·

Delta más cercano.

CANADIAN PORTER-CABLE

DELTA SERVICE CENTERS

ALBERTA

Bay 6, 2520-23rd St. N.E.

Calgary, Alberta

T2E 8L2

Phone: (403) 735-6166

Fax: (403) 735-6144

MANITOBA

1699 Dublin Avenue

Winnipeg, Manitoba

R3H 0H2

Phone: (204) 633-9259

Fax: (204) 632-1976

QUÉBEC

1515 ave.

St-Jean Baptiste, Suite 160

Québec, Québec

G2E 5E2

Phone: (418) 877-7112

Fax: (418) 877-7123

BRITISH COLUMBIA

8520 Baxter Place

Burnaby, B.C.

V5A 4T8

Phone: (604) 420-0102

Fax: (604) 420-3522

ONTARIO

505 Southgate Drive

Guelph, Ontario

N1H 6M7

Phone: (519) 767-4132

Fax: (519) 767-4131

1447, Begin

St-Laurent, (Montréal),

Québec

H4R 1V8

Phone: (514) 336-8772

Fax: (514) 336-3505

The following are trademarks of PORTER-CABLE DELTA (Las siguientes son marcas registradas de PORTER-CABLE DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE DELTA): Auto-Set ® , BAMMER ® , B.O.S.S.

® , Builder’s Saw ® , Contractor’s Saw ® ,

Contractor’s Saw II™, Delta ® , DELTACRAFT ® , DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX ® , Flying Chips™, FRAME SAW ® ,

Grip Vac™, Homecraft ® , INNOVATION THAT WORKS ® , Jet-Lock ® , JETSTREAM ® , ‘kickstand ® , LASERLOC ® , MICRO-SET ® , Micro-Set ® , MIDI LATHE ® ,

MORTEN™, NETWORK™, OMNIJIG ® , POCKET CUTTER ® , PORTA-BAND ® , PORTA-PLANE ® , PORTER-CABLE ® &(design), PORTER-

CABLE ® PROFESSIONAL POWER TOOLS, PORTER-CABLE REDEFINING PERFORMANCE™, Posi-Matic ® , Q-3 ® &(design), QUICKSAND ® &(design),

QUICKSET™, QUICKSET II ® , QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II ® , SAFE-LOC ® , Sanding Center ® , SANDTRAP ® &(design), SAW

BOSS ® , Sawbuck™, Sidekick ® , SPEED-BLOC ® , SPEEDMATIC ® , SPEEDTRONIC ® , STAIR EASE ® , The American Woodshop ® &(design), The Lumber

Company ® &(design), THE PROFESSIONAL EDGE ® , THE PROFESSIONAL SELECT ® , THIN-LINE™, TIGER ® , TIGER CUB ® , TIGER SAW ® ,

TORQBUSTER ® , TORQ-BUSTER ® , TRU-MATCH™, TWIN-LITE ® , UNIGUARD ® , Unifence ® , UNIFEEDER™, Unihead ® , Uniplane™, Unirip ® , Unisaw ® ,

Univise ® , Versa-Feeder ® , VERSA-PLANE ® , WHISPER SERIES ® , WOODWORKER’S CHOICE™.

Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other countries. Las

Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden estar registradas en otros países.

PC-0704-149

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement