Makita BFT081F Instruction manual

ENGLISH (Original instructions)
INSTRUCTION MANUAL
Cordless Screwdriver
BFT020F
BFT021F
BFT040F
BFT042F
BFT080F
BFT081F
BFT122F
BFT123F
004242
IMPORTANT: Read Before Using.
1
ENGLISH (Original instructions)
SPECIFICATIONS
Model
Fastening
torque
BFT020F
BFT021F
BFT040F
BFT080F
BFT122F
BFT042F
BFT081F
Hard joint
0.5 - 2 N·m
0.5 - 2 N·m
1 - 4 N·m
3 - 8 N·m
5 - 12 N·m
1 - 4 N·m
3 - 8 N·m
5 - 12 N·m
Soft joint
0.5 - 2 N·m
0.5 - 2 N·m
1 - 3.5 N·m
3 - 6.5 N·m
5 - 10 N·m
1 - 3.5 N·m
3 - 7.5 N·m
5 - 12 N·m
540
320
950
540
320
1,200
700
390
No load speed (min-1)
Dimensions
BFT123F
200 x 65 x 251mm
(with Battery Cartridge BH9020/BH9020A)
200 x 71 x 242 mm
(with Battery Cartridge BH1220C)
200 x 65 x 274 mm
(with Battery Cartridge BH9033/BH9033A)
200 x 71 x 251 mm
(with Battery Cartridge BH1233C)
Net weight
1.4 kg
1.5 kg
Rated voltage
D.C.9.6V
D.C.12V
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003
END004-4
Model BFT123F
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
Read instruction manual.
Cd
Ni-MH
Li-ion
Sound pressure level (LpA) : 71 dB(A)
Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 80 dB (A).
Wear ear protection
Only for EU countries
Do not dispose of electric equipment or
battery pack together with household
waste material!
In observance of European Directive
2002/96/EC on waste electric and
electronic equipment, 2006/66/EC on
batteries and accumulators and waste
batteries and accumulators and their
implementation in accordance with
national laws, electric equipment and
battery pack that have reached the end
of their life must be collected separately
and returned to an environmentally
compatible recycling facility.
ENG900-1
Vibration
The vibration total value (tri-axial
determined according to EN60745:
ENG901-1
•
•
Intended use
The tool is intended for screw driving in wood, metal
and plastic.
•
ENG905-1
noise
level
sum)
Work mode: screwdriving without impact
Vibration emission (ah) : 2.5 m/s2 or less
Uncertainty (K) : 1.5 m/s2
ENE033-1
Noise
The typical A-weighted
according to EN60745:
vector
determined
•
Model BFT020F, BFT021F, BFT040F, BFT042F,
BFT080F, BFT081F, BFT122F
Sound pressure level (LpA) : 70 dB(A) or less
Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 80 dB(A)
2
The declared vibration emission value has been
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
The vibration emission during actual use of the
power tool can differ from the declared emission
value depending on the ways in which the tool is
used.
Be sure to identify safety measures to protect the
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
ENH101-16
3.
Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical safety
4.
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
5.
Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
6.
Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
7.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
8.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use
of a cord suitable for outdoor use reduces the risk
of electric shock.
9.
If operating a power tool in a damp location is
unavoidable, use a ground fault circuit
interrupter (GFCI) protected supply. Use of an
GFCI reduces the risk of electric shock.
Personal safety
10. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
11. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
12. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energising power
tools that have the switch on invites accidents.
13. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.
14. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
For European countries only
EC Declaration of Conformity
We Makita Corporation as the responsible
manufacturer declare that the following Makita
machine(s):
Designation of Machine:
Cordless Screwdriver
Model No./ Type: BFT020F, BFT021F, BFT040F,
BFT042F, BFT080F, BFT081F, BFT122F, BFT123F
are of series production and
Conforms to the following European Directives:
2006/42/EC
And are manufactured in accordance with the following
standards or standardised documents:
EN60745
The technical documentation is kept by:
Makita International Europe Ltd.
Technical Department,
Michigan Drive, Tongwell,
Milton Keynes, Bucks MK15 8JD, England
30.1.2009
000230
Tomoyasu Kato
Director
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, 446-8502, JAPAN
GEA006-2
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1.
Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2.
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
3
objects, that can make a connection from one
terminal to another. Shorting the battery
terminals together may cause burns or a fire.
27. Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water.
If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery
may cause irritation or burns.
Service
28. Have your power tool serviced by a qualified
repair
person
using
only
identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
29. Follow instruction for lubricating and
changing accessories.
30. Keep handles dry, clean and free from oil and
grease.
15.
Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes, jewellery
or long hair can be caught in moving parts.
16. If devices are provided for the connection of
dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce dustrelated hazards.
Power tool use and care
17. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
18. Do not use the power tool if the switch does
not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous
and must be repaired.
19. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
20. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
21. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
22. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
23. Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
Battery tool use and care
24. Recharge only with the charger specified by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of fire
when used with another battery pack.
25. Use power tools only with specifically
designated battery packs. Use of any other
battery packs may create a risk of injury and fire.
26. When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
GEB050-2
CORDLESS SCREWDRIVER
SAFETY WARNINGS
1.
2.
3.
4.
5.
Hold power tool by insulated gripping
surfaces, when performing an operation
where the fastener may contact hidden wiring.
Fasteners contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
Always be sure you have a firm footing.
Be sure no one is below when using the tool
in high locations.
Hold the tool firmly.
Keep hands away from rotating parts.
Do not touch the bit or the workpiece
immediately after operation; they may be
extremely hot and could burn your skin.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this
instruction manual may cause serious personal
injury.
ENC005-2
IMPORTANT SAFETY
INSTRUCTIONS
FOR BATTERY CARTRIDGE
1.
4
Before using battery cartridge, read all
instructions and cautionary markings on (1)
2.
3.
4.
5.
6.
7.
8.
9.
battery charger, (2) battery, and (3) product
using battery.
Do not disassemble battery cartridge.
If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
If electrolyte gets into your eyes, rinse them
out with clear water and seek medical
attention right away. It may result in loss of
your eyesight.
Do not short the battery cartridge:
(1) Do not touch the terminals with any
conductive material.
(2) Avoid storing battery cartridge in a
container with other metal objects such
as nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current
flow, overheating, possible burns and
even a breakdown.
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 C (122 F).
Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.
Be careful not to drop or strike battery.
Do not use dropped or struck battery.
FUNCTIONAL DESCRIPTION
•
CAUTION:
Always be sure that the tool is switched off and the
battery cartridge is removed before adjusting or
checking function on the tool.
Installing or removing battery cartridge
Always switch off the tool before insertion or
removal of the battery cartridge.
For Models BFT020F, BFT021F, BFT040F, BFT080F,
BFT122F
•
1. Battery cartridge
2. Button
2
1
004243
To remove the battery cartridge, withdraw it from
the tool while pressing the buttons on both sides of
the cartridge.
•
To insert the battery cartridge, align the tongue on
the battery cartridge with the groove in the housing
and slip it into place. Always insert it all the way
until it locks in place with a little click. If not, it may
accidentally fall out of the tool, causing injury to
you or someone around you.
For Model BFT042F, BFT081F, BFT123F
•
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1.
2.
3.
4.
Charge
the
battery
cartridge
before
completely discharged.
Always stop tool operation and charge the
battery cartridge when you notice less tool
power.
Never recharge a fully charged battery
cartridge.
Overcharging shortens the battery service life.
Charge the battery cartridge with room
temperature at 10 C - 40 C (50 F - 104 F).
Let a hot battery cartridge cool down before
charging it.
Charge the Nickel Metal Hydride battery
cartridge when you do not use it for more
than six months.
1. Red part
2. Button
3. Battery cartridge
1
2
3
004244
•
•
5
To remove the battery cartridge, withdraw it from
the tool while sliding the button on the front of the
cartridge.
To insert the battery cartridge, align the tongue on
the battery cartridge with the groove in the housing
and slip it into place. Always insert it all the way
until it locks in place with a little click. If you can
see the red part on the upper side of the button, it
is not locked completely. Insert it fully until the red
part cannot be seen. If not, it may accidentally fall
out of the tool, causing injury to you or someone
around you.
At this time, recharge it for about five seconds
before use.
Do not use force when inserting the battery
cartridge. If the cartridge does not slide in easily, it
is not being inserted correctly.
•
NOTE:
•
Please contact Makita Authorized Service Center if
the warning lamp of the battery cartridge does not
light up when using or charging.
Refresh charging
Refreshing battery adapter (optional accessory) can
refresh an inactive battery cartridge.
•
Refresh charging should be done once a week.
•
When you charge a new battery cartridge or a
battery cartridge that has not been used for a long
time, it may not accept a full charge. In this case,
refresh charging must be done. The battery
cartridge may decrease the tool performance,
because the chemical substance of the battery
cartridge is inactive.
Switch action
1. Switch trigger
1
Checking the remaining battery capacity
004245
Indicating lamp
(C)
E
orange
CAUTION:
Before inserting the battery cartridge into the tool,
always check to see that the switch trigger
actuates properly and returns to the "OFF"
position when released.
To start the tool, simply pull the switch trigger. Release
the switch trigger to stop.
F Capacity
•
80% - 100%
60% - 80%
40% - 60%
10% - 40%
0% - 10%
Reversing switch action
Indicating lamp
F Capacity
E
orange
1. Reversing
switch lever
80% - 100%
60% - 80%
40% - 60%
10% - 40%
0% - 10%
A
1
B
001254
For BH9020A, BH9033A
When charging
When the charging begins, the first (far left) indicating
lamp begins to flicker. Then, as charging proceeds, the
other lamps light, one after the other, to indicate the
battery capacity.
When using
When the tool is switched on, the lamps will light after 2
seconds to indicate the remaining battery capacity.
When the tool is switched off, the light goes out. If the
battery has not been used for a long time, or is needed
refresh charging, the orange lamp begins to flicker. Use
Makita refreshing adapter to refresh the battery.
•
004246
CAUTION:
Always check the direction of rotation before
operation.
•
Use the reversing switch only after the tool comes
to a complete stop. Changing the direction of
rotation before the tool stops may damage the tool.
•
When not operating the tool, always set the
reversing switch lever to the neutral position.
This tool has a reversing switch to change the direction
of rotation. Depress the reversing switch lever from the
A side for clockwise rotation or from the B side for
counterclockwise rotation.
When the reversing switch lever is in the neutral
position, the switch trigger cannot be pulled.
•
CAUTION:
A battery cartridge extracted from the charger that
has been unplugged with the battery cartridge
inserted does not indicate the battery capacity due
to its protective function even if the tool is switched
on after the battery insertion into the tool.
6
Lighting up the lamps
1. Front lamp
1
004247
CAUTION:
Do not look in the light or see the source of light
directly.
Pull the switch trigger to light up the lamp. The lamp
keeps on lighting while the switch trigger is being pulled.
The light automatically goes out 10 seconds after the
switch trigger is released.
•
NOTE:
•
Use a dry cloth to wipe the dirt off the lens of lamp.
Be careful not to scratch the lens of lamp, or it
may lower the illumination.
LED indicator
1. LED indicator
1
004338
The lamp on the tool shows the following functions.
7
Status of the LED indicator/beeper
Function
Status
Action to be taken
LED indicator
Auto-stop fastening
Delayed re-start
This function works when the tool has reached
the preset fastening torque and normal
tightening has been completed. This helps
overtightening to be avoided.
Lights up in green for
approximately one
second.
For approximately one second after auto-stop
fastening, the tool does not start even if the
switch trigger is pulled.
Insufficient fastening has been performed
Warning against
when the switch trigger has released before
insufficient fastening
reaching the preset fastening torque.
Beeper
-
Lights up in red.
A long beep
-
Retighten the
screw
Warning for battery
cartridge capacity
This indicates the appropriate time to replace
the battery cartridge when the battery power
becomes low.
Flickers in red slowly.
Replace the battery
A series of long
with fully charged
beeps
one
Checking the
remaining battery
capacity, Autostop
This function works when the battery power
is almost used up. At this time, tool stops
immediately.
Lights up in red.
A long beep
Check the LED
indicator, light and
beeper operation
This function works to check the proper
operation of the LED indicator, light and
beeper when a battery cartridge has been
inserted into the tool.
Lights up first in green,
next red.
A series of very
short beeps
(And then the light
comes on.)
Anti-reset of
controller
This function works when an abnormal drop
of the battery voltage occurs for some reason,
and the tool stops.
Flickers in red and
green alternatively.
Replace the battery
A series of short
with fully charged
beeps
one
Overheat
This function works when the temperature
of the controller goes up very highly,
and the tool stops.
Flickers in red quickly.
Remove the battery
A series of short cartridge immediately
beeps
and cool the tool
down.
Operation error of
the switch trigger
This function works to avoid the tool's
immediate start upon insertion of battery
cartridge into the tool with the switch trigger
being pulled.
Flickers in red and
green alternatively.
A series of short Release the switch
trigger.
beeps
006388
8
Replace the battery
with fully charged
one
-
Adjusting the fastening torque
ASSEMBLY
1. Adjusting ring
2. Ring
1
•
2
CAUTION:
Always be sure that the tool is switched off and the
battery cartridge is removed before carrying out
any work on the tool.
Installing or removing driver bit or socket bit
004248
When you wish to drive machine screws, wood screws,
hex bolts, etc. with the predetermined torque, adjusting
the fastening torque as follows.
1.
First remove the battery cartridge from the tool.
2.
Loosen and remove the screw that secures ring.
3.
Rotate the ring in the front of the tool by hand so
that a hole can be seen below the ring.
4.
Place the battery cartridge in place and pull the
switch trigger. Release it so that the adjusting ring
rotates and becomes visible in the hole. And then
remove the battery cartridge.
4
1
2
3
5
6
3
7
004521
Use only bit or socket bit that has inserting portion
shown in the figure.
For tool with shallow bit hole: A=12mm, B=9mm
For tool with deep bit hole: A=17mm, B=14mm
Do not use any other driver bit or socket bit.
To install the bit, pull the sleeve in the direction of the
arrow and insert the bit into the sleeve as far as it will go.
Then release the sleeve to secure the bit.
1. Adjusting ring
2. Ring
3. Scale
4. Adjusting grip
5. Hole for
adjusting grip
6. Yellow line
7. Compression
spring
1. Bit
2. Sleeve
013091
5.
6.
7.
8.
Use an optional adjusting grip to adjust the
fastening torque. Insert the pin of the adjusting
grip into the hole in the front of the tool. And then,
turn the adjusting grip clockwise to set a greater
fastening torque, and counterclockwise to set a
smaller fastening torque.
Align the yellow line with your desired number on
the fastening torque scale.
Insert the battery cartridge and be sure that a
fastening torque has been set up by using a
fastening torque tester.
Rotate the ring in front of the tool and then tighten
the screw to secure the ring.
1
2
011406
To remove the bit, pull the sleeve in the direction of the
arrow and pull the bit out firmly.
NOTE:
•
If the bit is not inserted deep enough into the
sleeve, the sleeve will not return to its original
position and the bit will not be secured. In this
case, try re-inserting the bit according to the
instructions above.
NOTE:
•
Numbers on the fastening torque scale is a
guideline to set up your desired fastening torque.
9
OPERATION
BFT042F
Range of fastening capacity
Revolution angle ( )
Screwdriving operation
360
300
240
180
120
60
0
1
2
3
4
Torque
N.m
Revolution angle ( )
008232
004249
Place the point of the driver bit in the screw head and
apply pressure to the tool. Then switch the tool on.
When the clutch cuts in, the motor will stop
automatically. Then release the switch trigger.
NOTE:
•
Make sure that the driver bit is inserted straight in
the screw head, or the screw and/or bit may be
damaged.
Revolution angle ( )
BFT020F
BFT021F
0.5
1
1.5
2
Torque
N.m
006301
360
300
240
180
120
60
0
1
Range of fastening capacity
BFT040F
5
6
7
8
Torque
N.m
BFT081F
Range of fastening capacity
360
300
240
180
120
60
0
3
4
5
6
7
8 Torque
N.m
360
300
240
180
120
60
0
Range of fastening capacity
5
6
7
8
9
10
BFT122F
11
12
Torque
N.m
004253
2
3
Torque
4 N.m
Revolution angle ( )
Revolution angle ( )
4
006302
Revolution angle ( )
Revolution angle ( )
Use the tool within the limits of fastening capacity. If you
use the tool beyond the limits, the clutch does not work.
And the tool cannot deliver enough fastening torque.
Range of fastening capacity
3
004252
Limits of fastening capacity
360
300
240
180
120
60
0
BFT080F
Range of fastening capacity
360
300
240
180
120
60
0
004251
BFT123F
360
300
240
180
120
60
0
004254
10
Range of fastening capacity
5
6
7
8
9
10
11
12
Torque
N.m
NOTE:
•
The revolution angle means the angle which a
screw/bolt revolves when the tool attains to 100%
from 50% of desired torque.
•
Use of a low temperature conditioned battery
cartridge may sometimes give warning for battery
cartridge capacity by warning lamp and beeper
which makes the tool stop immediately. In this
case, the range of fastening capacity may be
inferior to those shown in the above even if a
charged battery cartridge is used.
OPTIONAL ACCESSORIES
CAUTION:
These
accessories
or
attachments
are
recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or
attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
•
Makita genuine battery and charger
•
Automatic refreshing adapter
•
Adjust grip
•
Protector
•
Grip Base Set
•
Grip 37
•
Anti kickback head
•
MAINTENANCE
•
•
CAUTION:
Always be sure that the tool is switched off and the
battery cartridge is removed before attempting to
perform inspection or maintenance.
Never use gasoline, benzine, thinner, alcohol or
the like. Discoloration, deformation or cracks may
result.
NOTE:
•
Some items in the list may be included in the tool
package as standard accessories. They may differ
from country to country.
Replacing carbon brushes
1. Limit mark
1
001145
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
Use a screwdriver to remove the brush holder caps.
Take out the worn carbon brushes, insert the new ones
and secure the brush holder caps.
1
1. Brush holder
cap
2. Screwdriver
2
004250
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers,
always using Makita replacement parts.
11
Makita Corporation
Anjo, Aichi, Japan
884500D222
12
www.makita.com