User s Manual

Thank you for purchasing our product.
Please read this User s Manual before
using the product.
STAND-ALONE DVMR
4 Channel Digital Video Multiplex Recorder
STAND-ALONE DVMR
ALL ABOUT IMAGE RECOGNITION & PROCESSING
DIGITAL VIDEO
DIGITAL VIDEO RECORDER
RECORDER
User s Manual VER 1.3
The most stable and reliable real stand-alone Digital Video Multiplex Recorder
ALL ABOUT IMAGE RECOGNITION & PROCESSING
ALL ABOUT IMAGE RECOGNITION & PROCESSING
SAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC
SHOCK. DO NOT OPEN!
CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN COVERS.
NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
This label may appear on the bottom of the unit due to space limitations.
The lightning flash with an arrowhead symbol within an equilateral triangle is intended
to alert the user to the presence of uninsulated “ dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to
presence of important operating and maintenance (Servicing) instructions in the
literature accompanying the appliance.
WARNING : TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE UNITS NOT
SPECIFICALLY DESIGNED FOR OUTDOOR USE TO RAIN OR MOISTURE.
Attention: installation should be performed by qualified service Personnel only in
accordance with the National Electrical Code or applicable local codes.
Power Disconnect. Units with or without ON-OFF switches have power supplied to
the unit whenever the power cord is inserted into the power source ; however, the unit
is operational only when the ON-OFF switch is in the ON position. The power cord is
the main power disconnect for all unites.
ALL ABOUT IMAGE RECOGNITION & PROCESSING
ALL ABOUT IMAGE RECOGNITION & PROCESSING
ALL ABOUT IMAGE RECOGNITION & PROCESSING
FCC INFORMATION
4. Arrangement RS-232C pin
RS-232C
A CLASS A computing device subject to certification by the Commission shall be identified pursuant to
par.2.925 et Seq of the chapter. In addition, the label shall include the following statement:
Pin No.
Definition
1
NC
2
RxD
3
TxD
4
NC
C o m m
P o rt
1
5
GND
6
NC
7
NC
8
NC
9
NC
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received,
including interference that may cause undesired operation.
5
6
9
RS-232C
Where a device is constructed in two or more sections connected by wires and marketed together, the
statement specified in this Section is required to be affixed only to the main control unit.
The users manual or instruction manual for the EUT shall contain the following statement or eqivalent.
DVMR unit
Other device (PC)
Caution : Changes or Modifications not expressly approved by the party responsible for compliance could
void the users authority to operate the equipment.
D-SUB 9 cable (twisted RS-232C cable)
#2
RxD
RxD
#2
#3
TxD
TxD
#3
#5
GND
GND
#5
If the EUT requires accessories such as special shielded cables and/or connectors to enable compliance
with emission limits, the instruction manual for the EUT shall include appropriate instructions on the first
page of the text concerned with the installation of the device that these special accessories must be used
with the device. It is the responsibility of the user to use the needed special accessories supplied with the
equipment.
For a CLASS A digital device or peripheral, the instructions furnished the user shall include the following or
similar statement placed in a prominent location in the text of the manual.
Note : This equipment has been tested and found to comply with the limits for a CLASS a digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of the this
equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at his own expense.
31
ALL ABOUT IMAGE RECOGNITION & PROCESSING
ALL ABOUT IMAGE RECOGNITION & PROCESSING
6. Specification and
Configuration
2. Configuration
Table of Contents
1.About this document
2
2. Before reading this document
2
3. Unit Description
3
1) Front Panel
2) Rear Panel
3
4
4. Installation
5
5. Operation
9
1) Log-in
2) Record
3) Play
4) Setting
1 Basic Operation
2 DISPLAY SETUP
3 CAMERA SETUP
4 TIME/DATE SETUP
5 ALARM/MOTION SETUP
6 RECORD SETUP
7 TCP/IP SETUP
8 MISCELLANEOUS SETUP
9
10
13
15
15
16
17
19
20
23
24
25
3. RS-232C Hex-codes table
Following ASCII-codes are for programmers who want to control the DVMR via RS-232C port.
RS-232C specification (baud rate/parity/data length/stop bit) : 19200, N, 8, 1
1 Byte ASCII-code.
MENU
‘M’
PIP/
MARK
‘I’
CH1
‘1’
UP
‘U’
PLAY
‘P’
FRZ
‘F’
CH2
‘2’
DN
‘J’
MODE
‘D’
SEQ/
SPEED
‘Q’
CH3
‘3'
LEFT
‘H’
PANTILT
‘T’
ZOOM
‘Z’
CH4
‘4’
RIGHT
‘K’
29
6. Specification & Configuration
1) SPECIFICATIONS
2) Stand alone DVMR
3) RS-232C Hex-codes table
4) Arrangement RS-232C pin
29
30
30
31
DEFAULT KEY ‘0’ (Default setup: Displays and records on Quad mode)
30
1
ALL ABOUT IMAGE RECOGNITION & PROCESSING
ALL ABOUT IMAGE RECOGNITION & PROCESSING
6. Specification and
configuration
1. SPECIFICATIONS
Before installing stand alone DVMR, be sure to thoroughly review and follow the instructions in this
MODEL NO
Stand alone DVMR
INPUT
OUTPUT
VIDEO I/F
HORIZONTAL RESOLUTION
S/N RATIO
COLOR
MONITORING
METHOD
480TV LINES
Also, when connecting with external application, first turn the power OFF and follow manual
instruction for appropriate installation.
16.7 MILLION
LIVE & PB AVAILABLE
PIP
AVAILABLE
SEQUENCE
AVAILABLE
FULL : 720(H)X480(V) ACTIVE PIXELS
1/4 SCREEN : 360(H)X240(V) ACTIVE PIXELS
2. Before reading this document
1. This document is intended for both the administrator and users of stand alone DVMR Model.
0.1~30 FRAME/SEC (EACH CHANNEL)
MATERIAL
HDD
COMPRESSED PICTURE
JPEG
PICTURE RECORDING
METHOD
User’s Manual. Pay particular attention to the parts that are marked NOTICE.
MORE THAN 4dB
FULL, QUAD DISPLAY
2. This manual contains information for configuring, managing and using stand alone DVMR Model.
QUAD SCREEN RECORDING
FIELD SWITCHER METHOD FULL SCREEN RECORDING
3. To prevent fire or electrical shock, do not expose the product to heat or moisture
REC, MODE
REAL-TIME/ TIME-LAPSE / EVENT
4. Be sure to read this manual before using stand alone DVMR Model.
TRACK PLAY
SEARCH, STILL
WEB INTERFACE
POST ALARM FUNCTION
TCP/IP with client software
5. For questions and technical assistance of this product, contact your local dealer.
1~59SEC, CONTINUOUS TIMING ESTABLISHMENT POSSIBILITY
BACK-UP
CONVENTIONAL VCR, TIME LAPS VCR (VCR OUTPUT PROVIDED)
REMOTE BACK-UP USING TCP/IP
INTERNAL BACK-UP(MARK IMAGE)
OTHERS
RS232C, RS485, MAX 4 ALARM INPUT
Strong recommendation on installation of the DVMR unit
PAN/TILT/ZOOM AND FOCUS
REMOTE CONTROL : EXTERNAL EQUIPMENT, WIPER,PUMP,FAN AND
HEATER
1. Check electricity at the place you want to install the DVMR unit is stable and meets our
electricity requirements.
Unstable electricity will cause malfunction of the unit or give critical damage to the unit.
CAMERA CONTROL
CONFIGURATION
4 HDD
OPERATION TEMPERATURE
OPERATION HUMIDITY
MECHANICAL
3 OUTPUT VBS : 1.0VP~P.75 OHM UNBALANCED (BNC TYPE)
ZOOM
SPEED
OTHER
FUNCTION
4 CH INPUT 1.0 VP-P, 75 OHM UNBALANCED (BNC TYPE)
SPLIT SCREEN
SCREEN QUALITY
RECORDING
/PLAY
FUNCTION
1. About this document
IR REMOTE CONTROLLER
DIMENSION
WEIGHT
POWER SUPPLY
PLUG&PLAY
INTERNAL 1 OR 2 HDD
OPTIONAL HDD BAY SUPPORT
4HDD /1UNIT, MAX. 5 UNITS
ACCEPT MIXED USAGE OF HDD FROM DIFFERENT MANUFACTURERS
41F~ 104F (5C~ +40C)
LESS THAN 90%
BUILT-IN
2. Several chips on the main board of the DVMR unit and hard disk drive inside the unit generate
heat, and it must be properly discharged.
Do not put any objects just beside exhaust port(fan) on the left side of the unit and do not close
up an opening (fresh air in-take) on the right side of the unit..
3. Put the DVMR unit at well-ventilated place and do not put heat-generating objects on the unit.
When it is installed inside 19 inch mounting rack together with other devices, please check builtin ventilation fan of the rack is properly running.
19" RACK SIZE 1U , 44X434X360 mm
APPROX. 5KG (HDD 1EA)
DC ADAPTER (12V DC 4.5A)
29
2
ALL ABOUT IMAGE RECOGNITION & PROCESSING
ALL ABOUT IMAGE RECOGNITION & PROCESSING
3. Unit Description
5. Operation
6
MARK IMAGE SETUP (Internal backup)
1. Front Panel
1
POWER
Indicates the start and end
location of stored images.
6
13
MARK IMAGE SETUP
Indicates the number of stored
images.
TOTAL SAVE FRAME
START MARK TIME
----/--/-- --/--/-EMD MARK TIME
----/--/-- --/--/-DELETE MARK IMAGE
PLAY MARK IMAGE
SYSTEM SETUP
OVERWRITE
1
2
3
4
PIP
FRZ
SEQ
ZOOM
DISPLAY SETUP
CAMERA TITLE
TIME/DATE SETUP
ALARM/MOTION
SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
RECORD
PLAY
MENU
SETUP
PLAY
MODE
P/T
ENTER
2
3
SPEED
MARK
4
5
7
8
9
10
11
12
1. POWER SWITCH WITH LED : DC power switch with LED
Before you turn off DC power switch off, we strongly recommend you to press
[MENU] button first to make HDD not in writing process.
Generally speaking, cutting power to system may cause trouble in DVMR
system or damage to HDD if HDD is in writing process, and we ask you to
press [MENU] button first to protect HDD from being damaged or system
failure before you press DC power switch off in practical operation.
BUZZER SETUP
ID/PW SETUP
SCHEDULE REC
SETUP
PANTILT CMD SETUP
HDD INFORMATION
MARK IMAGE SETUP
PRODUCT ID
0
Deletes or replay marked images.
SELECT
, PRESS ENTER
MARK IMAGE is very useful function, because it protects marked images from being overwritten.
During playback, you can mark images to store them on HDD separately from normal pictures. Those
marked pictures are not deleted even though you clear data on HDD or even after HDD starts to overwrite.
1) While replaying, press
PIP
button to select images.
MARK
2. MENU : Used when changing the menu of SYSTEM SETUP. If you press [MENU] button, recording stopped.
3. PLAY/ENTER : Starts playback, and in some functions, it is used as the SELECT key.
4. MODE : Changes to quarterly split screen or Full display screen.
Then“PAUSE”, “SPEED” and “MARK” are displayed on top of the screen.
2) At paused mode, press [LEFT]/[RIGHT] button to select frames you want to mark as many as wanted.
3) Press
PIP
button once more to complete MARK IMAGE SETUP for images you selected.
MARK
5. P/T : Manages PAN/TILT CONTROLLER.
4) Therefore all images in between
PIP
button remain not deleted unless you delete marked image on purpose.
MARK
6. 1,2,3,4 : Chooses each indicated camera.
5) When you want to mark large amount of images, cancel PAUSE by pressing
FRZ
button.
7. PIP/MARK : Assigns PIP (Picture in picture) or MARK IMAGE to protect selected image from being overwritten.
That is, press
FRZ
button, and search images replayed in actual speed.
8. FRZ : : Display screen is paused.
Then press
PIP
again to complete MARK IMAGE SETUP.
MARK
9. SEQ/SPEED : The display screen automatically rotates, and assigns playback speed and direction.
6) If the MARK IMAGE space given in the HDD gets to be full, “FULL” message appears and
10. ZOOM : Enlarges the display screen by 200%
PIP
button does not work any more.
MARK
11. Remote Controller Sensor Input Window
(HDD space for MARK IMAGE : stores about 10 minutes in normal picture taking-condition.)
12. Direction button
7) To replay marked image, select PLAY MARK IMAGE, and to delete select DELETE MARK IMAGE.
13. LED Lamps : Represent status of operation
NOTICE : Marked images stored on specific part of HDD, allocated for MARK IMAGE, is not deleted
when “HDD CLEAR” is activated. It can be erased only by DELETE MARK IMAGE.
NOTICE : If the Input window (IR receiver) is covered, the remote controller may not work.
NOTICE : If several buttons are simultaneously or incorrectly pressed, the system may not function properly.
3
7
PRODUCT ID
Serial number of products. Necessary for manufacturer to know manufacturing date, program version
number, and others.
28
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1
01:00-03:00 ON
04:00-05:00 ON
ALL ABOUT IMAGE RECOGNITION & PROCESSING
3.Unit Description
5. Operation
Just record from 1 to 3 and from 4 to 5, and does not record for the rest hours.
2
01:00-03:00 OFF
04:00-05:00 OFF
2. Rear Panel
Not record from 1 to 3 and from 4 to 5, and records for the rest hours.
3
01:00-03:00 ON
04:00-05:00 OFF
2
3
4
7
5
9
Just record from 1 to 3 (When both ON and OFF are set, priority is on ON.)
4 PANTILT COMMAND SETUP : When PTZ camera whose protocol is already incorporated into this DVMR
system (Default PTZ camera) is connected to this DVMR, just select model of
PTZ camera in PANTILT COMMAND SETUP. If user want to connect PTZ
camera which is not one of Default PTZ camera, users must input protocols of
PTZ camera or speed dome camera by themselves in USER DEFINE SETUP.
For detail procedure, refer to manual for incorporating protocol of PTZ camera
into DVMR system.
PANTILT COMMAND SETUP
SYSTEM SETUP
DISPLAY SETUP
CAMERA TITLE
TIME/DATE SETUP
ALARM/MOTION SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
1. DRX-502A[DEFAULT]
2.AECD-2000
3.USER DEFINE
RS-232C
ALARM
D D C N N G D D D D
-- + O C O N 4 3 2 1 ETHERNET
D
M
CH1
CH2
CH3
CH4
VCR
V
G
A
DC 12V
MONITOR
LOOP
1
6
8
10
11
1. RS-232C Port Connection
2. PAN/TILT Controller
3. Sensor Input/Output
DRX-502A [DEFAULT]
USER DEFINE SETUP
BUZZER SETUP
ID/PW SETUP
SCHEDULE REC
SETUP
PANTILT CMD SETUP
HDD INFORMATION
MARK IMAGE SETUP
PRODUCT ID
RS485 RELAY
Comm Port
3. NOTE for scheduled recording :
When scheduled recording is set, DVMR unit does not record before the set time. It only starts recording at
START time and ends at END time.
4. LAN (TCP/IP)
5. Camera Connection
SELECT
, PRESS ENTER
6. LOOP Output
7. VCR Connection
Procedure to control PTZ camera while you see live picture
Display of PANTILT COMMAND
1. Default PTZ camera : First select PTZ camera model connected to DVMR unit in the PANTILT COMMAND
SETUP menu. In live view mode, press [P/T] button and set CAM (Starts from 000) at camera ID which
is set on PTZ camera (DIP switch on PTZ camera) before you connect it to DVMR unit. Then select
command you want to execute using [LEFT] and [RIGHT] buttons. While you press [PLAY] button,
command you selected is executed.
2. USER DEFINE : In case you input protocols of PTZ camera which is not one of Default cameras, select
USER DEFINE in PANTILT COMMAND SETUP. Then press [P/T] button and set CAM (Ranges from
001 to 004) at any one from 001 to 004. CAM number must be the same as CH number which you set
when you input protocol of PTZ camera in USER DEFINE. Using [LEFT] and [RIGHT] button, select
command you want to execute and press [PLAY] button to execute selected command. While you press
[PLAY] button, command you selected is executed.
8. MONITOR Connection
9. VGA Connection
10. S-VHS Connection
11. D/C Power Connection
NOTICE : When connecting with other applications, be sure to turn off the system.
5 HDD INFORMATION
1
HDD DATA LIST : Shows general information of HDD.
2
HDD AUTO DETECT : Allows to detect HDD just in case first HDD search after purchase failed.
27
4
ALL ABOUT IMAGE RECOGNITION & PROCESSING
4. Installation
ALL ABOUT IMAGE RECOGNITION & PROCESSING
3
5. Operation
SCHEDULE REC SETUP :
▶ Procedure
SCHEDULE REC SETUP
1) Camera Connection
YY-MM-DD
02-07-06
SAT
02-07-07
SUN
02-07-08
MON
02-07-09
TUE
SYSTEM SETUP
DATE : Set by day
WEEK : Set by a day
of the week
DISPLAY SETUP
CAMERA TITLE
TIME/DATE SETUP
ALARM/MOTION
SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
Connect the camera to the CAMERA INPUT on the Rear Panel of the system.
BUZZER SETUP
ID/PW SETUP
SCHEDULE REC SETUP
PANTILT CMD SETUP
HDD INFORMATION
MARK IMAGE SETUP
PRODUCT ID
START
00:00
00:00
00:00
00:00
00:00
00:00
00:00
00:00
MODE : DATE
SELECT
-
,
END
24:00
24:00
24:00
24:00
24:00
24:00
24:00
24:00
ON/OFF
ON
ON
ON
ON
ON
ON
ON
ON
RESET : NONE
ENTER OR MODE
NONE : No reset
DATE : Reset selcted
date only
All : Reset all.
DC
LEVEL
V.P
VIDEO
CH2
CH3
CH4
VCR
CommPort
CH1
DC
V
G
A
Display of SCHEDULE REC SETUP
VIDEO
LENS
AC24V/DC12
MONITOR
LOOP
Rear part of CAMERA
Notice : This DVMR system automatically detects video system of camera you connected
to the unit when you boot DVMR system first. It is not necessary to set video
system separately, and DVMR system set at NTSC or PAL system automatically
when you boot the system.
Records according to schedule by day or a day of the week. Two recording time spans can be set for a
day and a day of the week respectively. In total, 4 recording time spans can be set in a day.
DVMR system records just as you set if you set SCHEDULE REC SETUP, and DVMR system records 24
hours a day if you do not set SCHEDULE REC SETUP.
1. Scheduled Recording for a day:
1) Press ENTER button to enter into SCHEDULE REC SETUP menu. In the sub-menu, you are requested
to select MODE or RESET. To first set up, select DATE or WEEK by pressing PLAY button.
2) Press
2) Monitor Connection (Composite Connection Method)
ENTER
MODE
button to be ready for editing. Then move to the location for change using direction button.
3) Set recording time for START and END with
Connect the monitor to the MONITOR OUT on the Rear Panel of the system
PLAY
button. Recording time increases by 30 minutes
ENTER
whenever
PLAY
button is pressed.
ENTER
4) After set START and END time for a day and set ON/OFF using
PLAY
button.
ENTER
5) After set all data, press
MODE
button once more to memorize settings you set in the system.
6) RESET is used to delete previously set recording schedule.
CH2
CH3
LOOP
CH4
VCR
CommPort
CH1
V
G
A
Select DATE, and move to the date by pressing
MODE
button, and press
PLAY
to delete.
ENTER
ALL deletes all recording schedule.
MONITOR
VIDEO A
VIDEO B
VIDEO C
IN
IN
IN
OUT
OUT
OUT
(NONE : Does not reset
DATE : deletes only selected date
7) When all input is ended, press
MENU
ALL : deletes all)
button to come back to SCHEDULE REC SETUP.
NOTICE : To move the cursor in SCHEDULE RECORD SETUP menu , RESET should be set at NONE.
2. Scheduled recording by a day of the week :
Notice : Connect camera or monitor to DVMR unit while DC power switch on the front panel
is off.
Recording is activated on a day of the week at the time set in advance. To set schedule for a day of the week,
first select WEEK in MODE of SCHEDULE REC SETUP by pressing
PLAY
button.
ENTER
5
Set recording time for each day of the week as the procedure for Scheduled Recording for a day.
26
ALL ABOUT IMAGE RECOGNITION & PROCESSING
5. Operation
8. MISCELLANEOUS SETUP
MISCELLANEOUS SETUP
1
BUZZER SETUP
ID/PW SETUP
SCHEDULE REC SETUP
PANTILT CMD SETUP
HDD INFORMATION
MARK IMAGE SETUP
PRODUCT ID
SELECT
ALL ABOUT IMAGE RECOGNITION & PROCESSING
2
3
4
5
6
7
BUZZER SETUP is available for each group as follows.
SYSTEM BUZZER
BUTTON BUZZER
ALARM BUZZER
MOTION BUZZER
LOSS BUZZER
You can set each group of BUZZER independently and
BUZZER is activated just in case you set at ON in
corresponding group of BUZZER SETUP.
, PRESS
4. Installation
3) Monitor (S-VHS) Connection
Connect S-VIDEO Monitor to MONITOR OUT(S-VHS) on the Rear Panel of the system.
Display of MISCELLANEOUS SETUP
1
BUZZER SETUP : Sets different kinds of BUZZER ON/OFF.
2
ID/PW SETUP : Sets User ID and PASSWORD.
CH2
CH3
CH4
VCR
DISPLAY SETUP
CAMERA TITLE
TIME/DATE SETUP
ALARM/MOTION SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
ID
CURRENT
NEW
CONFIRM
1,2,3,4
MARK
BUZZER SETUP
ID/PW SETUP
SCHEDULE REC SETUP
PANTILT CMD SETUP
HDD INFORMATION
MARK IMAGE SETUP
PRODUCT ID
<
<
<
<
PW
PW
PW
USER
VIDEO
A
IN
OUT
VIDEO
B
IN
OUT
, PRESS ENTER
4) VCR & VIDEO PRINTER Connection
Connect VCR or VIDEO PRINTER to VCR OUT on the Rear Panel of the system.
Display of ID/PW SETUP
1) With [UP]/[DOWN] button, select item to be changed, and press
PLAY
VCR
button to edit.
ENTER
CH1
CH2
CH3
LOOP
PLAY
CH4
VCR
CommPort
2) With [LEFT]/[RIGHT] button, move to wanted location and use [UP]/[DOWN] button to
make Selection.
3) Press
V
G
A
MONITOR
button after every SETUP and to be ready for next SETUP item.
ENTER
VIDEO PRINTER
4) After entering current password, enter new password and enter new password once more to verify.
Notice : In the very first setup stage, the ADMIN PASSWORD is “1”, and USER PASSWORD is “2”.
Change PASSWORD as soon as this product is purchased.
25
VIDEO
C
IN
>
>
>
>
: INPUT PASSWORD
: ERASE PASSWORD
SELECT
V
G
A
MONITOR
LOOP
SYSTEM SETUP
CommPort
CH1
ID/PW SETUP
6
OUT
ALL ABOUT IMAGE RECOGNITION & PROCESSING
ALL ABOUT IMAGE RECOGNITION & PROCESSING
5. Operation
4. Installation
7. TCP/IP SETUP
5) Sensor Connection
TCP/IP option of this DVMR system enables user to see live pictures and recorded pictures via internet
line, far apart from DVMR unit. To see live pictures or recorded pictures of DVMR, users must input IP
address, Gateway, and Subnet mask in TCP/IP SETUP in DVMR first, and then input IP, PORT number
and PASSWOR(ADMIN password in DVMR unit) in Remote Viewer Program installed on client PC.
For detail procedure for installing Remote Viewer Program and setting up, refer to manual for Remote
Viewer program included in the package.
Connect the Sensor to the SENSOR INPUT/OUTPUT on the Rear Panel of the system
Terminal block
RELAY
ALARM
D D C N N G D D D D
-- + O C O N 4 3 2 1
D
M
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
Alarm1
Alarm2
Alarm3
Alarm4
GND
NO( Normal Open )
NC( Normal Close)
COM
COM NC NO GND D4 D3 D2 D1
1
IP ADDRESS : Enter numbers using direction buttons and
press [MENU] button.
SYSTEM SETUP
3 SUBNET MASK : Enter numbers using
direction buttons and press [MENU] button.
Relay output : COM+NC, COM+NO OR COM+NC+NO
Alarm input : Short-circuit between Alarm1, Alarm2, Alarm3 or Alarm4 and GND is recognized as alarm.
NOTICE : Sensor input is RECOGNIZED as LOW when alarm signal is on a level with GND,
and it is recognized as HIGH when alarm signal is FLOATING or 5V. Following is internal circuit.
5
V
D1
Internal Circuit
4 MAC ADDRESS : It is unique ID number
provided by the manufacturer, and the user
should not change under any condition.
RS 485 : Connect to PTZ camera
RJ-45 (ETHERNET) : Connect to LAN, WAN or Internet
PTZ
CAMERA
RS-232C
Client program
(remote viewer)
DVMR unit
LAN, WAN, or Internet
DHCP server
RS-232C : Connect to PC to operate DVMR
D D C N N G D D D D
-- + O C O N 4 3 2 1 ETHERNET
D
M
For more details, refer to arrangements RS-232c pins in page 32.
7
5
, PRESS ENTER
PC
LAN
PC
Client program
(remote viewer)
Internet
Internet
DHCP SETUP
DVMR unit
Automatic
Leased line
Leased line w/ static IP
Cable modem w/ dynamic IP
Cable TV
(A)DSL
PTZ
Camera
TCP/IP setup
Router/Gateway
IP Sharer
b) Accessing to DVMR unit via Internet line
PC
Client program
(remote viewer)
ALARM
SELECT
2
3
4
1) Concept of accessing to DVMR unit via IP network
2) DHCP SETUP according to condition of IP network
a) Accessing to DVMR unit in the same Intranet(LAN)
6) Network Connection
RS485 RELAY
DISPLAY SETUP
CAMERA TITLE
TIME/DATE SETUP
ALARM/MOTION SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
1
IP ADDRESS
GATEWAY
SUBNET MASK
MAC ADDRESS
DHCP SETUP
5 DHCP SETUP : In case you connect DVMR
unit to LAN network under router/Gateway/IP
sharer which has DHCP server function, set
DHCP SETUP at DHCP, and DVMR unit automatically gets
TCP/IP SETUP
IP data automatically during the process of booting.
In case you connect DVMR unit to leased line with static IP or Router/Gateway connected (A)DSL line
(with static IP or dynamic IP), you are requested to set DHCP at MANUAL and input IP data manually.
For details, refer to Remote Viewer manual.
PC
Thus, there is a danger of damage, when the sensor input goes to a Negative level or
voltage higher than 5V.
TCP/IP SETUP
2 GATEWAY : Enter numbers using direction
buttons and press [MENU] button.
(A)DSL
modem
w/
dynamic
IP
24
or
static IP
Router
or
Gateway
DHCP SETUP
DVMR unit
Leased line : Manual
Cable modem : Automatic
DHCP SETUP
DVMR unit
Manual
Other devices
Port Forwarding
PPPoE
(IP Forwarding)
protocol
For details of TCP/IP SETUP in DVMR unit and PC, refer to “Remote Viewer manual” included in the package.
24
ALL ABOUT IMAGE RECOGNITION & PROCESSING
6. RECORD SETUP
5. Operation
ALL ABOUT IMAGE RECOGNITION & PROCESSING
4. Installation
7) HDD connection
RECORD SETUP
DISPLAY SETUP
CAMERA TITLE
TIME/DATE SETUP
ALARM/MOTION
SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
:
:
:
:
:
:
HDD CLEAR
HDD FULL
RECORD MODE
RECORD TYPE
RECORD SPEED
PRIORITY MODE
SYSTEM SETUP
HDD CLEAR
HDD FULL
RECORD MODE
RECORD TYPE
RECORD SPEED
PRIORITY MODE
SELECT
NO
OVERWRITE
TIMER
FIELD
60FPS
NONE
1
2
3
4
5
6
MAIN BOARD
, PRESS
HDD
(MASTER)
HDD
(SLAVE)
Connect main board and HDD using IDE HDD cable and power cable
included in the package.If you install just a unit of HDD, jumper setting
of HDD must be on Mater, as specified by HDD manufacturer, and
you can install it at any location of HDD1 or HDD2.
In case you install 2 HDDs, HDD1 must be master and HDD2 is slave,
and jumper setting must be done properly as specified by HDD manufacturer.
Fix HDD on the bottom of DVMR case using screws included in the package.
Screws must be inserted from outside of the bottom.
Display of RECORD SETUP
HDD CLEAR : If YES is selected, it deletes content of the HDD.
1
Notice : All contents of the HDD is deleted and cannot be restored.
As times go by, HDDs in a DVMR unit will have bad sectors one after the other.
Pictures to be recorded in bad sectors shall be damaged, and you will see incomplete pictures
whenever you replay. However, our DVMR unit operates normally even though there is some bad
sectors in hard disk drives.
2
HDD FULL : Select OVERWRITE or STOP RECORD. If OVERWRITE is selected, it delete previous contents
on HDD to overwrite when HDD is full.
3
RECORD MODE
1
2
3
4
4
Notice : Formatting before installation is not required, because DVMR system automatically detects HDD and formats.
In the first operation after installation of HDD, first clear all data on HDD and set at FACTORY DEFAULT in
SETUP menu of DVMR system.
8) Power Connection
Connect the power to the POWER CONNECTION on the Rear Panel of the system,
and turn on the switch.
TIMER : Records by time.
TIMER+ALARM : Records by time or when the ALARM comes in. (POST-ALARM Functionality)
MOTION : Records only when MOTION is detected.
MOTION+ALARM : Records by MOTION or when the ALARM comes in.
DC 12V
RECORD TYPE
1
2
FIELD : Records images from each camera in rotation
60 fields/sec at 720X240 resolution
Selected for higher resolution recording.
QUAD :Records 4 images of 360X120 resolution from each camera simultanuously at 720X240 resolution
In total 60 fields/sec.
Select for moving picture level recording.
5
RECORD SPEED : Adjusts recording frame rate : 0.1 indicates 1 field per 10 seconds.
(60/30/15/10/5/2/1/0.5/0.2/0.1 FPS)
6
PRIORITY MODE : Assigns recording priority of a specific channel.
1
NONE : Each of 1,2,3,4 does not have priority.
2
1
3
1,2 :
:
Notice : To turn off DC power switch on the front panel of DVMR case, be sure to press [MENU] button first.
If you press [MENU] button, DVMR system stops recording, and you can cut power to DVMR unit
while HDD head is not in writing mode. It is necessary to press [MENU] button first and turn DC power
switch off to protect HDD head from being damaged and eliminate possibility of mal-function of DVMR unit.
9) Turn on the POWER and Log-in to the system
Follow direction in the Log-in part of this manual to input the PASSWORD and start the system.
Factory default password for account manager is “1”, for user “2”
Gives priority to #1 camera, and records in the sequence of 1-2-1-3-1-4-1-2….
Gives priority to #1 and #2 cameras, and records in the sequence of 1-2-3-1-2-4-1-2-3.
23
10) Detail setup in SYSTEM SETUP
For detail setup, refer to the instruction of SYSTEM SETUP.
8
ALL ABOUT IMAGE RECOGNITION & PROCESSING
ALL ABOUT IMAGE RECOGNITION & PROCESSING
5. Operation
5. Operation
1. Log-in
4
1
Enter the password
default P/W : 1
LOGIN DVR SYSTEM
1) Press
MOTION MASK SETUP : Set detection area.
button to enter the
MENU
EDIT MODE : SELECT EACH CELL
P/T
: CHANGE EDIT MODE
MODE
: CHANGE CHANNEL
ENTER
: MASK ON/OFF
: CURSOR MOVE
system menu after starting the system.
PASSWORD
(
)
2) LOGIN DVR SYSTEM window appears as
1,2,3,4 :
MARK :
With the direction button,
choose MASK area.
SYSTEM SETUP
INPUT PASSWORD
ERASE PASSWORD
2
DISPLAY SETUP
CAMERA TITLE
TIME/DATE SETUP
ALARM/MOTION SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
shown on the left.
Input or modify
3) Use
1
2
3
button to enter
4
ALARM SETUP
ALARM LIST SETUP
MOTION SETUP
MOTION MASK SETUP
password that has 1 to 8 numbers.
Display of Login DVR SYSTEM
4) Use
PIP
Display of MOTION MASK SETUP
button to change.
MARK
1. Press
5) After entering the password, press
MENU
P/T
button to choose desired EDIT mode.
button to go back to the system menu.
2. Use [LEFT]/[RIGHT] button to assign BLOCK, and press
button to set.
PLAY
If password entered matches previously set number, “ADMIN GRADE LOGIN OK” message appears.
ENTER
3. MASK area in green color is detection area, and the rest is no detection area.
If password entered does not match previously set number “CURENT PW INPUT ERROR” message
4. Detected area is indicated in Green, and not detected area is indicated as colorless.
appears.
5. With
Factory default password set by manufaturer is as below.
USER (User) : “2”
NOTICE : To protect hard drive from damaged, turn off the power switch of DVMR unit after you first
press [MENU] button. If you press [MENU] button, DVMR unit stops recording, and HDD
head is not in the process of writing.
NOTICE : We recommend you to enter your own password as per procedure in 5-4)-
button, select channel (1,2,3,4,quad) to set for each camera.
Setup is possible only on the Full screen.
The system is equipped with two passwords.
ADMIN (Administrator) : “1”
MODE
8
-
2
SELECT VER LINE
: Select all in a vertical line.
CLEAR VER LINE
: Clear all in a vertical line.
SELECT HOR LINE
: Select all in a horizontal line.
CLEAR HOR LINE
: Clear all in a horizontal line.
SELECT BLOCK
: Select by BLOCK.
When
(page.25)
CLEAR BLOCK
: Clear the BLOCK.
to change the password.
button is pressed, [START] is displayed.
SELECT ALL CELLS
: Select all.
CLEAR ALL CELLS
: Clear all.
Then select blocks using direction button.
And press
PLAY
ENTER
NOTICE : Be sure to memorize the changed password.
NOTICE : When logged into USER MODE, only DISPLAY SETUP and TIME/DATE TYPE SETUP is possible.
9
PLAY
ENTER
22
button to set.
ALL ABOUT IMAGE RECOGNITION & PROCESSING
ALL ABOUT IMAGE RECOGNITION & PROCESSING
5. Operation
2) PAGE : Deletes current PAGE.
3) ALL : Deletes ALL.
5. Operation
2. RECORD
Move to alarm number in the list using [UP]/[DOWN] button, and press
MODE
button to mark “*”.
4. GOTO : Starts playback from the marked item in the list.
Move to an item in the list using [UP]/[DOWN] button, and press
Indicates recording speed
60FPS : 60 Fields/sec
MOTION : records when motion
is detected
1. PLAY
MODE
button to mark.
Changes to Playback Mode from Recording.
Indicates recording mode
REC : represents recording in
Field Switch Mode
Nothing displayed in Quad Mode
Indicates recording conditions
ALARM : records when alarm
condition is detected
Refer to Playback part(PAGE.13)of this
3
MOTION SETUP :
manual.
Camera selected
Adjust to Left/Right
2002 / APR / 01
60FPS REC
2. MODE
CAM1
When
MOTION SETUP
PM 01:00:00
CAM2
button is pressed, the full screen
MODE
Indicates
camera channel
of each channel and quarterly split screen is played
SYSTEM SETUP
DISPLAY SETUP
CAMERA TITLE
TIME/DATE SETUP
ALARM/MOTION SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
ALARM SETUP
ALARM LIST SETUP
MOTION SETUP
MOTION MASK SETUP
CHANNEL NUM
: 1
SENSITIVITY GRADE
LOW [-----------------------] HIGH
DETECT WINDOW NUM
: 01
AUTO FREEZE TIME
: OFF
MOTION REC DURATION
: 1 SEC
Size of object in motion.
If you set the Detect Window
Number at high like 10 or 15,
motion of small objects are not
deteted.
CAM3
by turns.
With
1
2
3
4
button, select
Display of Recording Mode
full screen of each camera.
SELECT
, PRESS
CAM4
When motion detected,
pause screen for set time
1. Indicates address of camera
001~255
3. Set ON/OFF
for selected
command
3. P/T
CHANNEL NUM : Selected camera number
SENSITIVITY : Adjusts motion Detection Sensitivity. (Not Sensitive
Sensitive)
DETECT WINDOW NUM : Detects moving objects bigger than DETECT WINDOW NUM.
1. Press
P/T
2002 / APR / 01
60FPS REC
button.
2.Use [UP]/[DOWN] button to choose the ADDRESS
P/T
CH1
FOCUS FAR
EXIT : PRESS [P/T]
CAM1
Can choose from 1 to 20. If DETECT WINDOW NUM value is 5, motion detections
PM 01:00:00
CAM2
of the P/T camera.
is activated only in case 5 cells are simultaneously detected.
3. Use [LEFT]/[RIGHT] button to select the command
AUTO FREEZE TIME : When MOTION is detected, the screen freezes for set time automatically.
Not to use this functionality, set at OFF.
Setup Time : 1,2,3,5,10 SEC
CAM3
CAM4
for P/T camera you want to transmit.
4. With
PLAY
button, select ON/OFF.
ENTER
MOTION REC DURATION : Sets duration of recording when a motion is detected.
In most of cases, while you press PLAY button, it is
ON, and OFF while not pressed. ENTER
Set value from 1 sec to 3 minutes according to frequency of motion,
and FACTORY DEFAULT value is 1 sec.
21
5. Press
screen
P/T
button to come back to recording
10
Display of PAN/TILT Control
(Ex: DRX-502A model)
2. Select
Command
FOCUS FAR
FOCUS NEAR
FOCUS AUTO
PAN RIGHT
PAN LEFT
TILT UP
TILT DOWN
ZOOM IN
ZOOM OUT
AUTO PAN
LIGHT CMD
WIPER CMD
PUMP CMD
POWER CMD
FUNTION 1
FUNTION 2
FUNTION3
ALL ABOUT IMAGE RECOGNITION & PROCESSING
ALL ABOUT IMAGE RECOGNITION & PROCESSING
5. Operation
5. Operation
5. ALARM/MOTION SETUP
4. PICTURE IN PICTURE (PIP)
1. Use
1
3
2
Indicates if “SEQ” button
selection.
button to select a camera
4
ALARM/MOTION SETUP
Indicates “FRZ” key
selection.
NOTICE : PIP is not available in quarterly split screen.
PIP
2. Press
button.
SELECT
1
3
2
4
, PRESS
SELECT
CAM1
Display of ALARM/MOTION SETUP
1
button select the channel of smaller screen.
SEQ
, ENTER OR MODE
Move to play screen of relate
appropriate time.
button, select the
camera channel in full screen, and with [LEFT]/[RIGHT]
4. Press
DATE
TIME
TYPE
CALM
………………………………………………………
001
02/04/01
21 : 14 : 11
3_H_
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
SORT : TIME DELETE
GOTO
2
3
4
2002/APR/1
PM 09:22:06
60FPS
REC
PIP
FL
PIP WINDOWS MOVE : OFF
MOVE ON/OFF : PRESS PRZ
MARK
3. With [UP]/[DOWN] or
NO
1
ALARM SETUP
ALARM LIST SETUP
MOTION SETUP
MOTION MASK SETUP
and set a full screen.
C: CAMERA
A : ALARM
L : LOSS
M :MOTION
ALARM LIST SETUP
3
Sort
method
SORT
CH
TIME
TYPE
DELETE
MARK
PAGE
ALL
1 ALARM SETUP : Sets type of alarm sensors connected to DVMR unit.
button to make the image in smaller
SPEED
Display of PICTURE IN PICTURE
OFF : No alarm sensor is connected.
NC : Normal Closed alarm sensor. When an event happens, Contact is opened.
NO : Normal Open alarm sensor. When an event happens, Contact is closed.
screen rotate.
To change the location of smaller screen, press
2
FRZ
button and use direction button to move to desired
ALARM DURATION : Duration of recording, when an ALARM is activated.
location.
5. FRZ
SELECT LIST TYPE : Select type of event to be enlisted in the event list. “A” indicates Alarm, “L”
indicates Loss, and “M” indicates Motion. You can select NONE if you do not
want to have event list, and ALM if you want all of Alarm, Loss and Motion are
enlisted in event list, by pressing [LEFT] and [RIGHT] button.
ALARM POP-UP : When an alarm is activated, display screen is switch to full screen of image from
relevant channel, and a color of camera number is changed to red.
If an alarm is activated from 2 channels, display screen is changed to quarterly split
screen (Quad screen), and a color of camera number of relevant channel is change to red.
Indicates if “FRZ”
button selection.
FRZ
1. Live full screen pauses when
button is pressed.
When #1 camera is
paused in QUAD screen
2. To pause quarterly split screen,
press
FRZ
button, and with
1
2
3
4
button
2002 / APR / 01
60FPS REC
PM 01:00:00
FRZ
2
select channel. On the right of the camera name, “FRZ”
CAM1 FRZ
CAM2
message appears and the LIVE screen of that channel
ALARM LIST SETUP : Shows list of alarms up to 400. If total alarm exceeds 400, it overwrites from the beginning.
Alarm list is very helpful to manage DVMR system.
1. With [LEFT]/[RIGHT] button, select SORT, DELETE or GO TO.
2. SORT
will pause. When pressed once more, it will come back to
CAM3
CAM4
PLAY
Press
button to select submenu of SORT ,that are CH ,TIME and TYPE.
ENTER
1) CH : Sort by CHANNEL
LIVE screen.
2) TIME : Sort by TIME
3) TYPE : Sort by TYPE
3. DELETE
NOTICE : When
FRZ
selected,
Pause Screen
1
2
3
4
button or
MODE
button do not work.
Press
PLAY
button when DELETE is highlighted, and select MARK, PAGE or ALL using [LEFT]/
ENTER
[RIGHT] button and press
PLAY
button.
ENTER
To move to full screen of each camera, press
FRZ
button once more to end Freeze mode.
11
1) MARK : Deletes marked item in the list.
20
ALL ABOUT IMAGE RECOGNITION & PROCESSING
5. Operation
ALL ABOUT IMAGE RECOGNITION & PROCESSING
5. Operation
6. SEQ
1.In LIVE full screen, press
4. TIME/DATE SETUP
SEQ
button to make picture from each channel rotate.
SPEED
2. It does not operate in quarterly split screen.
3. During automatic rotation, press
SEQ
button to stop automatic rotation.
SPEED
TIME/DATE SETUP
SET TIME/DATE
SET TIME/DATE TYPE
SET TIME/DATE
YEAR
MONTH
DAY
HOUR
MINUTE
SECOND
1
2
4.During automatic rotation, press
2002/APR/15
PM 09:23:17
SELECT
, PRESS
2 - 7
(PAGE.16). It is possible to select between 1 second to 99 seconds.
, PRESS
2002 / APR / 01
60FPS REC
Display of TIME/DATE SETUP
1
SET TIME/DATE : Can set year/month/time/minute/second.
PM 01:00:00
A
B
CAM1
CAM2
C
D
CAM3
CAM4
Use [UP]/[DOWN] button to assign Year/Month/Time/Minute/Second and use [LEFT]/[RIGHT]
button to change the value.
2
button to stop automatic rotation and move to quarterly split screen.
To change the time interval of the automatic rotation, change the value of SEQUENCE INTERVAL as per procedure
in 5-4)-
SELECT
MODE
2002 / APR / 01
60FPS REC
AB
Full screen
automatically rotates
by the value of
SEQUENCE
INTERVAL in A/B/C/
D/A/B/C..
Display of 4-split (Quad) screen
SET the notation of TIME/DATE :
PM 01:00:00
SEQ
CD
Automatic rotation of the Full Screen
7. Sensor Recording
1. HOUR DISPLAY :
TIME/DATE TYPE SETUP
Changes to AM/PM or 24hour time indication
2. DATE DISPLAY :
HOUR DISPLAY
: AM/PM
DATE DISPLAY
: ASIAN
MONTH DISPLAY
: ENGLISH
Converts into Asian type/American type/European type
SELECT
, PRESS
1) When there is sensor input, the recording starts.
2) It records for preset period of time
For detail setup, refer to RECORD SETUP : REC MODE SETUP in 5-4)- 6 - 3 (PAGE.23) for TIME+ALARM
and MOTION+ALARM and ALARM SETUP: ALARM DURATION in 5-4)- 5 - 1 (PAGE.20) for Time setup.
8. Scheduled Recording
Records by date and by day of the week.
Refer to MISCELLANEOUS SETUP ; SCHEDULE REC SETUP in 5-4)- 8 - 3 (PAGE.26) for detail setup.
3. MONTH DISPLAY :
9. Recording by MOTION DETECTION
Refer to ALARM/MOTION SETUP in 5-4)- 5
Month indication is changed to English or Number
Display of Time/Date TYPE
19
(PAGE.20~22).
10. NOTICE
1) Recording is stopped during SYSTEM SETUP.
2) Recording is stopped during playback, or search in playback mode.
3) Recording is not possible if no camera is connected.
12
ALL ABOUT IMAGE RECOGNITION & PROCESSING
ALL ABOUT IMAGE RECOGNITION & PROCESSING
5. Operation
5. Operation
3. Play
1. Playback setup
1
1) Press
CAMERA ACTIVE SETUP
:
Time recording
started.
button to begin playback.
PLAY
ENTER
2) Display screen as shown on the right will appear
PLAY
3) Press
button again to start playback from
CHs
STATUS
LIVE
REC
CH1
CH2
CH3
CH4
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ON
ON
ON
ON
ON
ON
ON
ON
ENTER
:
SCREEN POSITION
ADJUSTMENT
DEFAULT POSITION
CAM1
CAM2
CAM3
CAM4
2
ENTER
START picture.
START
END
:
:
2002/APR/12
2002/APR/20
AM 07:40:38
PM 02:11:56
GOTO
:
2002/APR/15
AM 00:00:00
Time recording
ended.
SELECT
, PRESS ENTER
(To start from a specific time, first set the
GO TO time before press PLAY button.)
3
ENTER
4) To come back to recording mode.
press
PLAY
button.
Display of Search(GOTO) mode
Indicate time to be
played.
Display of Screen Position Adjustment
Display of CAMERA ACTIVE Setup
3
ACTIVE CH SETUP :
2. GOTO time setting
With direction button, move to item to be changed, and press
1) At
3
PLAY
button to select ON/OFF.
ENTER
, use [LEFT]/[RIGHT] button to choose the date or time of GO TO.
1. STATUS : In normal cable condition it is indicated as ACTIVE, and when the cable is disconnected or
2) Use [UP]/[DOWN] button, set desired time.
has problem, it is indicated as LOSS.
3) Press
PLAY
button to replay from the GO TO time.
ENTER
2. LIVE : Decides whether to show LIVE screen image or not.
NOTICE : During playback or setting GO TO time, recording is stopped
3. REC : Decides whether to record relevant channel or not.
NOTICE : When value that is out of the range of start and end is entered, it starts from START time
4
SCREEN POSITION SETUP
NOTICE : When value is in the range of START and END, but there is no recorded pictures at the set time,
Use direction button to move the full screen according to the user’s needs.
it moves to the closest time of the recorded pictures.
5
COLOR BAR TEST : COLOR BAR CHART is generated.
3. Pausing and single frame advanced
Used for adjusting the monitor
1) During playback, press
2) After pressing
or left.
FRZ
FRZ
, press
button to pause. (Will replay when pressed once more)
SEQ
button and use [LEFT]/[RIGHT] button to advance single frame to the right
SPEED
13
18
ALL ABOUT IMAGE RECOGNITION & PROCESSING
ALL ABOUT IMAGE RECOGNITION & PROCESSING
5. Operation
5. Operation
4. Playback Speed Setup
3. CAMERA SETUP
1) During playback , press
SEQ
button.
SPEED
Playback speed
2) Display screen will appear as on the right.
3) Use [LEFT]/[RIGHT] button to move forward (FF) or
CAMERA SETUP
CAMERA COLOR SETUP
SELECT
backward (REW).
1
COLOR SETUP
TITLE SETUP
ACTIVE CH SETUP
SCREEN POSITION SETUP
COLOR BAR TEST
2
3
4
CH NUMBER
BRIGHTNESS
CONTRAST
SATURATION
HUE
GAIN
5
1
+2
-2
-8
+0
+0
Chosen
Chosen
1X PLAY SPEED
2X PLAY SPEED
4X PLAY SPEED
8X PLAY SPEED
16X PLAY SPEED
32X PLAY SPEED
60X PLAY SPEED
1X PLAY SPEED
1/2 PLAYSPEED
1/4 PLAYSPEED
1/8 PLAYSPEED
1/16 PLAYSPEED
1/32 PLAYSPEED
1/60 PLAYSPEED
4) Use [UP]/[DOWN] button to select the speed rate.
2002/APR/12
1X PLAY
(High speed up to x60 and slow speed up to 1field/60sec is possible.)
We recommend you to install 7200rpm EIDE hard disk drive.
, PRESS
SELECT
AM 07:40:38
SPEED
CAM1
CAM2
CAM3
CAM4
, PRESS
5400rpm EIDE hard disk drive is not good enough to retrieve
recorded data in high speed and slow speed playback mode.
Display of Camera Setup
Display of CAMERA COLOR SETUP
1
COLOR SETUP : Adjust Camera Image
CH NUMBER
BRIGHTNESS
CONTRAST
SATURATION
HUE
GAIN
: Select camera
: Adjust screen brightness
: Adjust color contrast
: Adjust color saturation
: Adjust color hue
: Adjust image signal level
(-31~ +32)
(-31~ +32)
(-20~ +32)
(-31~ +32)
(-31~ +32)
During playback at 60x speed, blue screen comes into view
instantaneously once in a while and you could not see some
pictures at that moment even though all they were recorded
correctly, due to limitation in speed of reading data on a hard
drive, and it is not a critical error in operation of DVMR unit.
Display of PLAYBACK SPEED SETUP
To see pictures you could not see, just go back for some seconds and
replay at a little lower speed than before.
5. Display Enlargement.
1) Choose camera by pressing
1
Right adjustment of each element in COLOR setup will increase picture quarterly displayed.
2) Press
We recommend you to adjust each element of COLOR SETUP for cameras and monitor to be connected
3) The display will enlarge by 200%
ZOOM
2
3
4
button.
button, during Playback or PAUSE mode.
to the DVMR unit, for better appearance.
ZOOM
4) Use direction button to move the area enlarged.
Press(X2 Enlargement)
CAMERA TITLE SETUP
0123456789. ,<>()-=
ABCD
▲
5) Press
ZOOM
to go back to Playback or FRZ mode.
EFGHIJKLMNOPQRSTUVW XYZa b
2
TITLE SETUP : Input TITLE of each camera
1) Use [LEFT]/[RIGHT] button to select CHANNEL and press
PLAY
ENTER
▶ CH1
CH2
CH3
CH4
(CAM
(CAM
(CAM
(CAM
1
2
3
4
)
)
)
)
button
NOTICE : Execute in FULL SCREEN of each channel.
When
SEQ
button is pressed, ZOOM does not work.
SPEED
2) Go into CHANNEL content and use [LEFT]/[RIGHT] button
SELECT
, PRESS ENTER
6. MARK IMAGE (Internal backup) SETUP
to move to item to be changed and use [UP]/[DOWN] button
During Playback, press
to change the letters.
Display of CAMERA TITLE SETUP
When modification is finished, press
Press
cdefghIjklmnopqrstuvwxyz
MENU
button to come back to the MAIN MENU.
17
PIP
button and choose pictures using [LEFT]/[RIGHT] button to protect selected
MARK
pictures from being overwritten when hard disk is full
Refer to MISCELLANEOUS SETUP : MARK IMAGE SETUP in 5-4)- 8 - 6
14
(PAGE.28) for details.
ALL ABOUT IMAGE RECOGNITION & PROCESSING
ALL ABOUT IMAGE RECOGNITION & PROCESSING
5. Operation
4. System Setup
5. Operation
2. DISPLAY SETUP
1. Basic Operation
This is about the contents displayed on the display screen.
DISPLAY SETUP
CAMERA TITLE
TIME/DATE SETUP
ALARM/MOTION SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
TIME/DATE
CAMERA TITLE
PB TIME/DATE
PB CAMERA TITLE
DVR STATUS
BORDER SET
SEQUENCE INTERVAL
DISPLAY TYPE
SELECT
1
2
3
4
button and press
MENU
button
to enter SETUP MENU.
2) Use [UP]/[DOWN] button to select setup item.
PLAY
button to enter sub-menu of selected SETUP.
ENTER
4) Press sub-menu item with [UP]/[DOWN] button, and change the value with [LEFT]/[RIGHT] button.
5) Press
PLAY
button to forward
:
:
:
:
:
:
:
:
ON
ON
ON
ON
ON
WHITE
01
COMPO
AM 07:40:38
1
2
3
4
5
6
7
8
B
CAM1
, PRESS
CAM3
CAM2
CAM4
D
F
Display of SYSTEM SETUP
button.
2) Log into the system by entering the password with
3) Press
2002/ARP12
60FPS REC
DISPLAY SETUP
SELECT UP/DOWN , ENTER
MENU
C
E
SYSTEM SETUP
1) Press
A
MENU
button to go backward.
Display of DISPLAY SETUP
1
TIME/DATE : A Date and time is indicated on LIVE screen.
2
CAMERA TITLE : Camera TITLE B is indicated on LIVE screen.
3
PB TIME/DATE : On Playback screen, C Date and Time is indicated.
4
PB CAMERA TITLE : Camera TITLE D is indicated on the Replay SCREEN.
5
DVR STATUS : E indicates status of operation, such as REC/REPLAY.
6
BORDER SET : Changes the color of the border F
ENTER
PLAY
button enables to enter and
MENU
button to go back.
ENTER
6) To go back to the very first SETUP condition recommended by manufacturer, set at FACTORY DEFAULT.
You can set at FACTORY DEFAULT all in one (as a whole) or group by group. When cursor is at
ALL SETUP, you can set at ON or OFF by pressing [ENTER] button. If you set ALL SETUP at ON, all
groups of settings are SET as per FACTORY DEFAULT recommended by manufacturer. If you set
ALL SETUP at OFF, then you are requested to set each group of settings separately one by one, ON or
OFF, and groups of settings set at ON shall be reset whenever you set at FACTORY DEFAULT.
To reset, you have to select ALL SET or each group of settings (ON or OFF), and then move to
RESET NOW and press [ENTER].
- WHITE/ BLACK
7
SEQUENCE INTERVAL : Sets rotating time interval of pictures . In full screen in live mode or
playback mode, pictures are rotating in a certain time interval
when you press
SEQ
button, and SEQUENCE INTERVAL is for it.
SPEED
Items remain unchanged when FACTORY DEFAULT is selected.
1. value of TIME/DATE SETUP
2. Date stored on HDD
3. Marked image (Internal backup)
4. ADMIN password
5. ALARM LIST SETUP
We recommend users to set at FACTORY DEFAULT in the first operation, and when you replaced
EPROM for updating DVMR program or replaced HDD.
15
( Time interval from 1 second to 99 seconds)
8
DISPLAY TYPE : Set at COMPO if you connected Composite monitor to DVMR unit, and set
at VGA if you connected VGA monitor (CRT type PC monitor) to DVMR unit, by
pressing [LEFT] and [RIGHT] buttons. VGA option of DVMR unit enables
users to connect CRT type PC monitor to DVMR unit, and it looks better in picture
quality and also we can save cost for monitor. PC monitor must support 800 x 600
resolution and multi-sink type. Our VGA option supports just part of TCT LCD monitor.
16