Zanussi ZC 85 L Specifications

REFRIGERATOR
ZC 85 L
INSTRUCTION BOOKLET
2222 063-24
IMPORTANT SAFETY INFORMATION
It is most important that this instruction book should be retained with the appliance for future
reference. Should the appliance be sold or transferred to another owner, or should you move house and
leave the appliance, always ensure that the book is left with the appliance in order that the new owner
can get to know the functioning of the appliance and the relevant safety information.
This information has been provided in the interest of safety. You MUST read it carefully before installing
or using the appliance.
Installation
¥
¥
¥
¥
¥
¥
This appliance is heavy. Care should be taken
when moving it.
It is dangerous to alter the specifications or
attempt to modify this product in any way.
Care must be taken to ensure that the appliance
does not stand on the electrical supply cable. If
the supply cord is damaged, it must be replaced
by a special cable available from your local
Service Force Centre.
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
Parts which heat up should not be exposed.
Whenever possible, the back of the appliance
should be close to a wall but leaving the required
distance for ventilation as stated in the installation
instructions.
The appliance should be left for 2 hours after
installation before it is turned on, in order to allow
the refrigerant to settle.
¥
Maintenance and Cleaning
¥
Do not allow children to tamper with the controls
or play with the product.
¥
Keep all packaging well away from children.
During Use
¥
This appliance is designed for domestic use only,
specifically for the storage of edible foodstuffs
only.
¥
Frozen food must NOT be re-frozen once it has
thawed out.
¥
Do not place carbonated or fizzy drinks in the
freezer.
¥
Do not remove items from the freezer if your
hands are damp/wet, as this could cause skin
abrasions or frost/freezer burns.
¥
Ice lollies can cause Ôfrost/freezer burnsÕ if
consumed straight from the freezer.
¥
ManufacturersÕ storage recommendations should
be strictly adhered to. Refer to relevant
instructions.
2
Switch off and unplug the appliance before
carrying out any cleaning or maintenance work.
Servicing
¥
This product should be serviced by an authorised
engineer and only genuine spare parts should be
used.
¥
Under no circumstances should you attempt to
repair the machine yourself. Repairs carried out
by inexperienced persons may cause injury or
serious malfunctioning. Refer to your local
Zanussi Service Force Centre and always insist
on genuine spare parts.
Child Safety
¥
The cooling plate or refrigerated freezer shelves
in this appliance contain channels through which
the refrigerant passes. If these are punctured this
will cause substantial damage to the appliance
and result in food loss. DO NOT USE SHARP
INSTRUMENTS to scrape off frost or ice. Under
NO circumstances should solid ice be forced off
the lining or shelves. Solid ice should be allowed
to thaw, when defrosting the appliance. See
Defrost Instructions.
At the end of the Appliance
Life
¥
When disposing of your appliance, use an
authorised disposal site.
¥
Remove the plug and ensure that any locks or
catches are removed, to prevent young children
being trapped inside.
CONTENTS
Instructions for the user
Important Safety Information
2
Instructions for the
installer
Description of the appliance
4
Technical specification
13
Operation
5
Installation
14
Before use
5
Positioning
14
Setting the temperature
5
Rear Spacers
14
Fresh food refrigeration
5
Electrical Connection
15
Normal operating sounds
5
Door Reversal
16
Dual purpose meat box
5
Movable shelves
6
Positioning the door shelves
6
CRISPÕN FRESH
6
Cool Check Guide
7
Hints and Tips
8
Maintenance and Cleaning
8
Internal cleaning
8
External cleaning
8
When the appliance is not in use
8
Changing the light bulb
9
Cleaning the filter
9
Defrosting
9
Something not working
10
Service and Spare Parts
11
Customer Care
11
Guarantee Conditions
12
2222 063-24
3
DESCRIPTION OF THE APPLIANCE
J
A
B
I
C
H
G
F
E
A- Dairy compartment
B- Can storage shelf
C- Can storage shelf
D- Bottle storage shelf
E- Salad crispers (to keep fruit and vegetables fresh)
F- Glass shelf
G- CrispÕn fresh filter
H- Cool Check Temperature Guide
I- Storage shelves
J- Thermostat control
4
D
OPERATION
Before using
Fresh food refrigeration
Remove all securing tapes. Wash inside the
appliance with lukewarm water and bicarbonate of
soda (5 ml to 0.5 litre of water).
To obtain the best performance, do not store warm
food or evaporating liquids in the refrigerator; do
cover or wrap the food, particularly if it has a strong
flavour.
Do not use soap or detergent as the smell may
linger. Dry thoroughly.
Setting the temperature
The temperature inside the refrigerator is regulated
by a thermostat with 6 temperature positions and an
ÒOFFÓ (O) position.
Position 1 = minimum coldness
Position 6 = maximum coldness
Do not cover the shelves with any protective
material, such as paper, cardboard or plastic, which
may obstruct the air circulation through them.
To help you use your refrigerator correctly, here are
some more useful hints:
Raw meat (beef, pork, lamb & wild fowl): wrap in
polythene bags and place on the glass shelf above
the salad crispers.
Turn the thermostat dial to the required position.
Meat can only be stored safely in this way for
one or two days at the most.
The intermediate position is usually the most
suitable (3-4).
Fruit & vegetables: these should be thoroughly
cleaned and placed in the bottom salad crispers.
The thermostat setting can vary as the temperature
inside the refrigeration compartment depends on the
following factors:
Butter & cheese: these should be placed in special
airtight containers or wrapped in aluminium foil or
polythene bags to exclude as much air as possible.
Ð room temperature
Milk bottles: these should have a cap and should be
stored in the bottle rack on the door.
Ð how often the door is opened
Ð how much food is stored
Ð position of the appliance
Normal Operating Sounds
Important
If the fridge is not defrosting correctly, it is possible
that because a very low temperature has been
selected, the motor is working continuously, which
prevents the defrost cycle from operating.
To ensure correct defrosting, a lower number should
be selected on the thermostat and you should notice
that the motor cuts out from time to time, which is
correct.
If you wish to return to a lower temperature, turn the
thermostat to a higher number, however you should
turn the setting lower occasionally to allow automatic
defrosting.
¥
You may hear faint gurgling or bubbling sounds
when the refrigerant is pumped through the coils
or tubing at the rear, to the cooling
plate/evaporator.
¥
When the compressor is on, the refrigerant is
being pumped round, and you will hear a whirring
sound or pulsating noise from the compressor.
¥
A thermostat controls the compressor, and you
will hear a faint ÕclickÕ when the thermostat cuts in
and out.
Dual purpose meat box
The meat box can also be used as a salad crisper.
5
Movable shelves
The walls of the refrigerator have runners so that
shelves can be positioned as desired.
D040
Positioning the door shelves
To permit storage of food packages of various sizes,
the door shelves can be adjusted in height.
To do this proceed as shown in the diagram.
PR260
PR262
Use and features of the CRISPÕN
AND FRESH filter
ÒCrispÕn freshÓ is the glass shelf on top of the salad
crispers which is fitted with special removable green
filters.
These filters allow cool air from the fridge to circulate
through the drawers but help prevent moisture loss.
By retaining moisture in foods such as fresh fruit,
vegetables and salad they are kept fresher for
longer.
6
D749
Cool Check Guide
The guide consists of a temperature sensitive strip
sealed in a shelf trim.
When the fridge is operating at the safe temperature
to store food the guide will appear black. If the
temperature rises above this level the guide will
show the words TOO WARM.
TOO WARM
Positioning of the Cool Check
The shelf with the cool check temperature guide
must be placed in the fridge according to the
instructions located on the fridge wall and always
ensure the guide is at the front.
If the Cool Check shows TOO WARM
In certain conditions the temperature guide may
show TOO WARM if:
¥
The fridge is switched off
¥
The door has been recently opened
¥
A quantity of warmer food has been introduced to
the fridge
¥
The fridge temperature is above the
recommended maximum for the safer storage of
food.
ZA
NU
SS
I
CCOO2
The cool check will change to show ÒTOO WARMÒ
very quickly after the door has been opened. It will
however take a number of hours to return to black,
indicating that the temperature is correct.
The appliance should be left overnight and the cool
check examined in the morning. If the cool check
shows TOO WARM, turn the appliance to a colder
setting leave overnight and examine again the
following morning.
Hints and Tips
¥
The guide is only suitable for use in the model
supplied.
¥
The guide will not operate in the freezer
compartment.
¥
When cleaning the shelf take care not to immerse
in water, and wipe away any spills.
7
HINTS AND TIPS
Food Storage
¥
To obtain the best results from the appliance
neither hot foods nor liquids which may
evaporate, should be placed in the larder
compartment.
¥
Keep the time between buying chilled food and
placing it in your refrigerator as short as possible.
¥
Do not push food together too much, try to allow
air to circulate around each item.
¥
Do not store food uncovered.
¥
Remove suspect food from your refrigerator and
clean, refer to Maintenance and Cleaning.
Energy Saving Advice
¥
Do not install the appliance close to sources of
heat, such as a boiler or radiator.
¥
Locate the appliance in a cool well ventilated
room and make sure that the air openings of the
appliance are not obstructed.
¥
Always leave warm food to cool down to room
temperature before placing in the fridge.
¥
Try to avoid keeping the door open for long
periods or opening the door too frequently as
warm air will enter the cabinet and cause the
compressor to switch on unnecessarily often.
¥
Ensure there are no obstructions preventing the
door from closing properly.
¥
It is advisable to peridocally clean the
refrigeration system at the back of the appliance
with a duster or vacuum cleaner.
MAINTENANCE AND CLEANING
Before any maintenance or cleaning work is carried
out, DISCONNECT the appliance from the
ELECTRICITY supply.
Once or twice a year dust the condenser (black grill)
and the compressor at the back of the appliance,
with a brush or vacuum cleaner, see figure.
Internal cleaning
Clean the inside and accessories with warm water
and bicarbonate of soda (5ml to 0.5 litre of water).
Rinse and dry thoroughly.
NEVER USE DETERGENTS, ABRASIVE
POWDERS, HIGHLY PERFUMED CLEANING
PRODUCTS OR WAX POLISHES, TO CLEAN THE
INTERIOR AS THESE WILL DAMAGE THE
SURFACE AND LEAVE A STRONG ODOUR.
CONDENSER
DEFROST
TRAY
COMPRESSOR
D273
External cleaning
When the appliance is not in use
Wash the outer cabinet with warm soapy water. Do
NOT use abrasive products.
When the appliance is not in use for long periods,
disconnect from the electricity supply, empty all
foods and clean the appliance, leaving the doors ajar
to prevent unpleasant smells.
An accumulation of dust will affect the performance
of the appliance and cause excessive electricity
consumption.
8
Changing the light bulb
Unscrew the light cover and then pull it outward
toward the middle of the cabinet. Unscrew the bulb
and replace it with a new 15 watt bulb (available
from your nearest Service Force Centre).
Replace the light cover by sliding it into its original
position and replacing the screw.
D411
Cleaning the filter
The filter is held by two small support frames which
press into position and are therefore easily removed
for cleaning. To do this, turn the glass shelf upside
down and release the frames as shown in figure.
The filters and the glass cover can be washed gently
in warm soapy water, they should not be put in the
dishwasher.
Replacement filters can be purchased as a spare
part from your local Zanussi Service Centre.
D711
Defrosting
The refrigerator automatically defrosts every time the
compressor stops. The water is discharged, via the
pipe, into a tray located at the back of the appliance
above the compressor, where it evaporates.
Important
To avoid defrost water overflowing into the fridge,
periodically clean the water discharge hole in the
centre of the V shaped drip collector at the back of
the refrigerator compartment behind the salad
crispers. Use the defrost cleaner provided which you
will find already inserted into the discharge hole.
D037
Remember to wash the defrost cleaner in hot soapy
water at regular intervals. Dry throughly before
replacing.
9
SOMETHING NOT WORKING
If the appliance is not working correctly, please carry out the following checks before contacting your local
Zanussi Service Force Centre
Symptom
Solution
No power to the appliance
Check there is power at the socket.
Check there is not a power cut by checking the
household lights.
Check the fuse has not blown.
The light does not come on
Ensure that the bulb is correctly fitted.
Replace the bulb if it has blown.
Check the door light switch is not jammed.
The temperature in the fridge
Check the temperature in the fridge is turned to the
correct setting relative to ambient conditions.
Check the ambient temperature is within the
applianceÕs operating limits of 10¡C to 32¡C.
Relocate the appliance if necessary.
The compressor runs continously
Adjust the thermostat to give correct temperature
control. See ÒSetting the temperatureÓ.
Check that the door is closed.
Large quantities of food have recently been placed in
the cabinet/and or door is frequently opened.
Check that air ventilation is not obstructed.
Noise
Refer to normal operating sounds.
Water under the salad bin
Check the drain hole is not blocked. (see
Maintenance and Cleaning).
If after the above checks your appliance still does
not operate correctly, contact your local Zanussi
Service Force Centre.
Please note that it will be necessary to provide proof
of purchase for any in-guarantee service calls.
10
In-guarantee customers should ensure that the
above checks have been made, as the engineer
will make a charge if the fault is not a mechanical
or electrical breakdown.
SERVICE AND SPARE PARTS
In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your
local Zanussi Service Force Centre by telephoning:-
0870 5 929929
Your telephone call will be automatically routed to the Service Force Centre covering your post code area.
For further details please see the accompanying Customer Care Booklet.
Before calling out an engineer, please ensure you have read the details under the heading ÔSomething Not
Working?
When you contact the Service Force Centre you will need to give the following details:
1.
Your name, address and post code
2.
Your telephone number
3.
Clear and concise details of the fault
4.
The model and serial number of the appliance (found on the rating plate)
5.
The purchase date
CUSTOMER CARE DEPARTMENT
For general enquiries concerning your Zanussi appliance or for further information on Zanussi products, please
contact our Customer Care Department by letter or telephone as follows:Customer Care Department
Zanussi
55-77 High Street
Slough
Berkshire
SL1 1DZ
Tel: 08705 727 727
11
GUARANTEE CONDITIONS
Standard guarantee conditions
We, Zanussi, undertake that if within 12 months of the date of the purchase this Zanussi appliance or any part
thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair
or replace the same FREE OF CHARGE for labour, materials or carriage on condition that:
The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.
The appliance has been used for normal domestic purposes only, and in accordance with the manufacturerÕs
instructions.
The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not
authorised by us.
All service work under this guarantee must be undertaken by a Zanussi Service Force Centre. Any appliance or
defective part replaced shall become the CompanyÕs property.
This guarantee is in addition to your statutory and other legal rights.
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these
hours in which case a premium will be charged.
Exclusions
This guarantee does not cover:
Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or
removable parts of glass or plastic.
Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the
European Community (EC) or European Free Trade Area.
Appliances found to be in use within a commercial environment, plus those which are subject to rental
agreements.
Products of Zanussi manufacture which are not marketed by Zanussi.
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new home
subject to the following qualifications:
The guarantee starts from the date you first purchased your product.
The guarantee is for the same period and to the same extent for labour and parts as exists in the new country
of use for this brand or range of products.
This guarantee relates to you and cannot be transferred to another user.
Your new home is within the European Community (EC) or European Free Trade Area.
The product is installed and used in accordance with our instructions and is only used domestically, i.e. a
normal household.
The product is installed taking into account regulations in your new country.
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your
new home. They will then ensure that the local Service Organisation is aware of your move and able to look
after you and your appliances.
France
Senlis
+33 (0)3 44 62 29 99
Germany
NŸrnberg
+49 (0)911 323 2600
Italy
Pordenone
+39 (0)1678 47053
Sweden
Stockholm
+46 (0)8 738 79 50
UK
Slough
+44 (0)1753 219 897
12
TECHNICAL SPECIFICATIONS
DIMENSIONS
Height
124
cm
Width
54
cm
Depth
57
cm
POWER SUPPLY VOLTAGE AND FREQUENCY
220-240 V / 50 Hz
TOTAL POWER ABSORBED
120 W
AVERAGE DAILY UNITS ELECTRICITY *
0.70 kWh
GROSS CAPACITY
230 l
NET CAPACITY
228 l
* This figure is based on standard test results in accordance with European Standard EN 153.
Actual consumption will depend on how the appliance is used and where it is located.
13
INSTALLATION
Important
IF YOU ARE DISCARDING AN OLD APPLIANCE
THAT HAS A LOCK OR CATCH ON THE DOOR,
YOU MUST ENSURE THAT IT IS MADE
UNUSABLE TO PREVENT YOUNG CHILDREN
BEING TRAPPED INSIDE.
Depending upon the position which you choose for
your appliance, you may wish to reverse the way in
which the door opens. To do this, refer to instructions
on ÒDoor reversalÓ.
Please ensure that when the appliance is
installed it is easily accessible for the engineer in
the event of a breakdown.
B
10 mm
You should also ensure that air can circulate freely
around the back and the top of the cabinet. There
must also be at least 100 mm (4Ó) distance between
the top of the cabinet and any overhanging kitchen
furniture (A). Ideally, the appliance should not be
positioned beneath overhanging furniture (B).
A
10 mm
This appliance is designed to operate in ambient
temperatures between 10¡C (50¡F) and 32¡C (90¡F).
It should be located in a dry atmosphere, out of
direct sunlight and away from extreme temperature
e.g. not next to a boiler or radiator, or in a very cold
room e.g. an outhouse, where the temperatures may
fall below 10¡C (50¡F). If these temperatures are
exceeded i.e. colder or warmer, then the appliance
may not operate correctly.
100 mm
Positioning
NP007
There should also be a gap of 25 mm either side of
the appliance. Do not obstruct the space
underneath. The back of the cabinet may be placed
close to the wall but must not touch it. DO NOT
install in places with restricted ventilation.
Adjust the level of the appliance by screwing out the
adjustable foot, or feet, at the bottom of the cabinet
using your fingers.
D200
Rear spacers
The plastic bag containing all relevant
documentation also contains two spacers to be fitted
into special holes in the back of the appliance.
Fit the spacers into the holes, taking care to ensure
that the arrow (A) is positioned as shown in the
Figure. Then turn them through 45¡ (arrow (A)
vertical) until they lock into place.
14
A
45°
PR60
Electrical connections
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
WARNING: THIS APPLIANCE MUST BE
EARTHED.
The manufacturer declines any liability should
this safety measure not be observed.
If the plug that is fitted to your appliance is not
suitable for your socket outlet, it must be cut off and
the appropriate plug fitted.
For replacement, use a 13amp BSI362 fuse. Only
ASTA or BSI approved fuses should be used.
The plug must not be used if the fuse cover/carrier is
lost. The cover/carrier is indicated by the coloured
insert at the base of the plug.
A replacement cover/carrier must be obtained from
your local Zanussi Service Force Centre whose
address is listed in the Customer Care Booklet which
accompanies your instruction manual.
This appliance complies with the E.E.C. Directive
No. 87/308 of 2.6.87 relative to radio interference
suppression.
This appliance complies with the following
E.E.C. Directives:
Remove the fuse from the cut off plug.
The cut off plug should then be disposed of to
prevent the hazard of shocks in case it should be
plugged into a 13amp socket in another part of your
home.
-
73/23 EEC of 19.2.73 (Low Voltage Directive)
and subsequent modifications;
-
89/336 EEC of 3.5.89 (Electromagnetic
Compatibility Directive) and subsequent
modifications.
Important
The wires in the mains lead are coloured in
accordance with the following code:
Green and Yellow
- Earth
Blue
- Neutral
Brown
- Live
If you fit your own plug, the colours of the wires in
the mains lead of your appliance may not
correspond with the markings identifying the
terminals in your plug, proceed as follows:
13 AMP. FUSE
13 AMP
GREEN & YELLOW
BROWN
BLUE
D207
CORD CLAMP
Connect the Green and Yellow (earth) wire to the
terminal in the plug which is marked with the letter
ÇEÈ or the earth symbol
yellow.
or coloured green and
Connect the blue (neutral) wire to the terminal in the
plug which is marked with the letter ÇNÈ or coloured
black.
Connect the brown (live) wire to the terminal in the
plug which is marked with the letter ÇLÈ or coloured
red.
The plug moulded onto the lead incorporates a fuse.
15
Door reversal directions
1. Disconnect from the electricity supply.
1
3
2. Gently lay the fridge on its back with the top held
away from the floor by 5-8 cm (2-3 inches) of
packing;
2
0°
18
3. Remove the bottom hinge (3), pin (1) and screw
(2);
2
4. Slide out the fridge door from pin (D), unscrew the
latter and then refit it on the opposite side;
5. Unscrew the foot on the left side and refit it on the
opposite side;
D299
6. Remove the two screws which mask the holes for
fixing the hinge from the left hand side;
7. Refit the door and the lower hinge (turning it
180¡), the pin (1) and the screw (2) as shown in
the Figure;
D
8. Remove plugs, unscrew the handle and refit it on
the opposite side.
Important
After completion of the door reversing operation,
check that the door gasket adheres to the cabinet. If
the ambient temperature is cold (i.e. in Winter), the
gasket may not fit perfectly to the cabinet. In that
case, wait for the natural fitting of the gasket or
accelerate this process by heating up the part
involved with a normal hairdryer on a low setting.
D590
D336
Printed on recycled paper
17
18