U s e r r M a n u a l l / / I I n s t t a l l l l a t t i i o n G u i i d e

1 5 " L C D T o u c h M o n i i t t o r r

Warning!

It will cause malfunction if the monitor is operating with unspecified power supply unit or incorrect power voltage. Do not exposure this unit in the rain or moisture environment to reduce the risk of fire or electric shock.

Content:

I.

FCC Warning Statement.............................................................................. 1

II.

Introduction ................................................................................................. 2

　 Features......................................................................................................................................2

　 Unpacking the monitor ..............................................................................................................2

III.

Installation.................................................................................................... 4

　 Touch Driver installation ...........................................................................................................5

　 Structure of OSD settings ..........................................................................................................9

IV.

For your safety .......................................................................................... 10

V.

Support timing chart ................................................................................. 10

VI.

Mechanical Dimension: ............................................................................ 10

VII.

Product General Specification ................................................................. 11

WARNING

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

Notice:

(1) A Unshielded-type power cord is required in order to meet FCC emission limits and also to prevent interference to the nearby radio and television reception. It is essential that only the supplied power cord by used.

(2) Use only shielded cables to connect I/O devices to this equipment.

(3) Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Version. 1.0 1

II. Introduction

The 15" LCD Touch Monitor is color TFT LCD monitor, integrate with resistive touch. Optional

MSR and 2 nd

display, please contact our regional distributor for further information.

 Features

- Optimal display resolution 1024 * 768

- VESA 75 * 75 mm wall mount standard

- Durable and sturdy base design

- Optional 3 tracks Magnetic Strip Reader (MSR)

- Optional variety of 2 nd

display (7”/8.4”)

- Adjustable viewing angel freely up to 90 degrees horizontally

- Low power consumption only 20W with CCFL backlight

 Unpacking the monitor

- Put the monitor on a clean surface, make sure the box in upright position.

- Remove packing materials from inside of box.

Version. 1.0 2

Check accessory

Please make sure all the accessory are included:

Standard Items a. b. c. d. e. f. a. LCD Monitor c. Touch driver / User Manual CD e. Power adaptor b. VGA cable d. Touch cable (USB or RS232) f. Power cable

Optional Items

a. b. a. MSR b. 2 nd

display ( 7” or 8.4” )

Version. 1.0 3

III. Installation

 I/O placement

 To PC

1 DC JACK

3 VGA

5 Dual USB A Type

7 RJ45(RS232)

2 DVI

4 USB B Type

6 RS232

1. Connect VGA cable from monitor to PC

2. Connect USB touch cable to PC

3. Connect DC plug to monitor and the other side to wall outlet

Version. 1.0 4

 Touch Driver installation

1. Double click “setup.exe” from driver menu 2. Click “next” from welcome window

3. Click “next” from choose destination location window 4. Click “next” from ready to install the program

5. Click “next” from setup type 6. Click “finish” when setup completed

Calibration procedures:

1. Double click “POS Touch+” icon to run calibration function

2. Follow 9 points linearity calibration procedures and save the data

3. Follow free draw calibration

4. Exit calibration menu

5. Reboot PC

Version. 1.0 5

 MSR installation (optional)

Components of MSR Kit:

1. Slide the MSR into the right position of the System.

2. Fasten the screws (x2).

 Second Display installation (optional)：

To install the Second Display, please open the VFD cover first.

Components of Second Display Kit with power adapter:

Version. 1.0

1. Fix the parts of Second Display modules as steps ❶  ❷  ❸ as above left picture shows. (detail steps as below)

❶ Put the second display upside down.

❷ Place the metal bracket onto the rear side of the second display and fasten the screws (x4) to fix metal bracket with the system.

6

❸ Align the plastic bracket into the right position of metal bracket.

(a) Align the plastic bracket onto the metal bracket.

(b) Push to left until the click sound appears.

2. Fasten the screw (x1) to fix the platic bracket and Second Display module with metal bracket.

3. Slide the Second Display Module into the slot.

Version. 1.0

4. Fasten the scrws (x2) to fix the Second Display moudle with the System.

5. Connect the VGA cable to the Second Display Module and the System.

6. Connect the DC piug to the Second Display Module and the other side to wall outlet.

7. Finish

7

 Control Buttons

Power

Auto Adjusting

Up

Down

Menu

Use the power switch to turn the power ON or OFF. We recommend to turn your system power on first, then the LCD monitor. a.) Pressing to execute AUTO-Adjusting function. This function will set the monitor display area to the optimal position. b.) Sometimes this function can't achieve the optimal effects. Please follow the manual adjusting procedure. a.) When OSD mode is activated (When “MENU” key is pressed). The two keys are used to select the adjustment items. b.) When adjustment item is selected, the two keys are defined to decrease or increase the value of each selected item.

When the light bar move other item, the key are used to select it, and read to adjust. Press the MENU key to activate the On Screen Display (OSD). Press twice to turn off the OSD. After 30 sec idle time, the OSD screen will automatically turn off.

Version. 1.0 8



Main

Menu

Structure of OSD settings

First Level Second Level

Auto Adjust

Luminance

Geometry

Brightness

Contrast

Exit

H. Position

V. Position

Clock

Phase

Exit

Third

Level

Operating Procedure

Press “UP” or “DOWN” to adjust H-phase &

H-position & V-position clock automatically.

Press “UP” key to increase brightness, “DOWN” key to decrease brightness.

Press “UP” key to increase contrast, “DOWN” key to decrease contrast.

Press “UP” key to shift screen right, “DOWN” key to shift screen left.

Press “UP” key to shift picture upward, “DOWN” key to shift picture downward.

Adjust sampling clock of analog to digital converter until clock is equal to pixel frequency of video input.

By varying this “UP” “DOWN” control the exact sampling time within the pixel can be adjusted.

9300K

6500K

5800K

Color

OSD

User Preset

Exit

H. Position

V. Position

OSD Timeout

Exit

Red

Green

Blue

Exit

Press “UP” or “DOWN” to choose three types of color temperature 9300°k, 6500°k and user define.

Adjust OSD frame horizontal location, press “UP” key to shift frame right, “DOWN” key to shift frame left , timeout and preset OSD.

Adjust OSD frame vertical location, press “UP” key to shift frame upward, “UP” key to shift frame downward , timeout and preset OSD.

Language

English

French

German

Italian

Spanish

Japanese

T. Chinese

S. Chinese

Recall

Color Recall

Recall All

Exit

Sharpness

Miscellaneous

Display

Information

Exit

Exit

Press “UP” or “DOWN” to choose any one of the following language, English, French, Germany,

Italy, Spain , Japanese, Traditional Chinese and

Simplified Chinese.

Recall the default value.

Press “UP” key to increase sharpness, “DOWN” key to decrease sharpness.

Version. 1.0 9

IV. For your safety

1. When move the monitor, always switch off power and disconnect all cables to avoid any danger.

2. Please use the power and signal cables correctly when install or bend it.

3. In case of notice any abnormal smell or noise, please stop operation and call the nearest dealer or service center.

V. Support timing chart

Timing

Mode

Mode 1

Mode 2

Mode 3

Mode 4

Reference

Standard

Resolution

Pixel

MHz

H

FH KHz FV Hz Interlace

Polarity

V

Polarity

VESA 1024×768 65.000

48.363

60.004

NO - -

VESA 1024×768 75.000

56.476

70.069

NO - -

VESA 1024×768 75.011

57.524

72.000

NO + +

VESA 1024×768 78.750

60.023

75.029

NO + +

210

397,17

365,2

Version. 1.0 10

VII. Product General Specification

Model 1 5 " " L C D T o u c h M o n i i t t o r r

COLOR BLACK

Display size

Display Area

Optimal Resolution

PANNEL Brightness

Contrast Ratio

Response Time

Viewing Angle(L/R/U/D)

Input Video signal connector

Power consumption

Input Frequency

Power supply

Temperature

Weight (Net)

Physical Dimension

Approvals

Touch Technology

Wall Mount type

Optional items

Wall Mount

15"

304.1 * 228 mm

1024 * 768

250 cd/m²s (typ)

600:1(typ)

8 ms (typ)

80 / 80 / 80 / 80 (typ)

D-Sub 15 pins+DVI-D

20W

H: 31.5-60.2 kHz ; V: 56.3-75Hz

DC 12V +/- 10%

Operating : 0℃~40℃ ; Storage : -10℃~50℃

4.67kgs

365.2 (W) * 338.6 (H) * 200 (D) mm

CE, FCC, BSMI, CCC

5W Resistive touch

VESA 75 * 75 mm

Bracket

2nd Display

Customer Display

7”/8.4”

VFD

Version. 1.0 11