- Computers & electronics
- Computer components
- System components
- Audio cards
- AJA
- KONA LH/LHe
- User manual
advertisement
www.aja.com
Published: 5/4/11
Installation and Operation
Guide
B e c a u s e i t m a t t e r s .
ii
Trademarks
AJA ® , KONA ® , Ki Pro® and XENA ® are registered trademarks of AJA Video, Inc. Ki Pro™, Io HD ™ and Io ™ are trademarks of AJA Video, Inc.
Apple, the Apple logo, AppleShare, AppleTalk, FireWire and Macintosh are registered trademarks of Apple Computer, Inc. Final Cut Pro, QuickTime and the QuickTime Logo are trademarks of Apple Computer, Inc. TASCAM is a registered trademark of TEAC Corporation.
All other trademarks are the property of their respective holders.
Notice
FCC Emission Information
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Changes or modifications not expressly approved by
AJA Video can effect emission compliance and could void the user’s authority to operate this equipment.
Contacting Support
Copyright © 2011 AJA Video, Inc. All rights reserved. All information in this manual is subject to change without notice. No part of the document may be reproduced or transmitted in any form, or by any means, electronic or mechanical, including photocopying or recording, without the express written permission of AJA Inc.
To contact AJA Video for sales or support, use any of the following methods:
180 Litton Drive, Grass Valley, CA. 95945 USA
Telephone: 800.251.4224 or 530.274.2048
Fax: 530.274.9442
Web: http://www.aja.com
Support Email: [email protected]
Sales Email: [email protected]
When calling for support, first read the Chapter on Troubleshooting at the back of this manual. You can often save time and effort by looking there first for simple remedies and information on how to get support from AJA and Apple Computer Inc.
KONA LHe Installation and Operation Manual — Limited Warranty
iii
Limited Warranty
AJA Video warrants that this product will be free from defects in materials and workmanship for a period of three years from the date of purchase. If a product proves to be defective during this warranty period, AJA Video, at its option, will either repair the defective product without charge for parts and labor, or will provide a replacement in exchange for the defective product.
In order to obtain service under this warranty, you the Customer, must notify AJA Video of the defect before the expiration of the warranty period and make suitable arrangements for the performance of service. The Customer shall be responsible for packaging and shipping the defective product to a designated service center nominated by AJA Video, with shipping charges prepaid. AJA Video shall pay for the return of the product to the Customer if the shipment is to a location within the
1 for paying all shipping charges, insurance, duties, taxes, and any other charges for products returned to any other locations.
This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate maintenance and care. AJA Video shall not be obligated to furnish service under this warranty a) to repair damage resulting from attempts by personnel other than AJA Video representatives to install, repair or service the product, b) to repair damage resulting from improper use or connection to incompatible equipment, c) to repair any damage or malfunction caused by the use of non-AJA Video parts or supplies, or d) to service a product that has been modified or integrated with other products when the effect of such a modification or integration increases the time or difficulty of servicing the product.
THIS WARRANTY IS GIVEN BY AJA VIDEO IN LIEU OF ANY OTHER WARRANTIES, EXPRESS
OR IMPLIED. AJA VIDEO AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. AJA VIDEO’S
RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE WHOLE AND
EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR ANY INDIRECT, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER AJA VIDEO OR
THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.
iv
KONA LHe Installation and Operation Manual — Table of Contents
Table of Contents
Chapter 1: Introduction
Chapter 3: Installation
1
2
Chapter 4: Final Cut Pro and Other Application Software
Chapter 5: Troubleshooting
Appendix A: Specifications
Appendix B: Glossary
Chapter 1: Introduction
Edge Shot Photo Here
Overview
Features
Hardware
The AJA KONA LHe brings the highest quality HD, SD and analog video/audio to an Apple Mac
Pro or G5 Mac running Final Cut Pro software. KONA LHe digital and analog interfaces are very high quality. KONA LHe supports 8 and 10 bit uncompressed video, DV25 and DV50 using the
DVCPRO codec, and JPEG—all on an Apple Mac Pro or G5. DVCProHD, HDV, and Apple RT
Extreme are all supported—and even accelerated by onboard hardware. Using superb 12 bit video A/D and D/A converters, analog formats like BetaCam SP also look excellent. In addition to high quality video, KONA LHe also supports balanced analog, AES/EBU, and embedded audio I/O, all at 24 bits and 48Khz. For simplified system integration, KONA LHe includes hardware sample-rate conversion for AES inputs (eliminating annoying synchronization hassles)—and RS-422 machine control.
The KONA LHe card offers a large number of unique features for optimum quality, ease of use, and support for a wide variety of workflows and environments. KONA LHe provides flexible standard definition and high definition capture and playback, a hardware downconverter for working in mixed SD/HD environments—and it supports both analog and digital audio/video
I/O.
• 10-bit uncompressed SD/HD QuickTime capture card
• 12-bit HD Analog Component I/O
• 12-bit SD Analog Component/Composite/S-Video I/O
• 10-bit hardware HD-to-SD downconversion
• DVCProHD hardware acceleration
• HDV hardware acceleration
1
1 1
2
Software
• Dynamic RT Extreme hardware acceleration
• SDI or HD-SDI Input, 2 independent SDI/HD-SDI outputs
• 2-channel analog balanced XLR audio I/O
• 2-channel AES XLR audio I/O
• 8-channel SDI embedded audio I/O
• HD/SD genlock on analog video inputs
• RS-422 Machine Control
• Final Cut Pro, Motion, After Effects, Combustion, and more
• Cables standard
• Optional KL-box Breakout Box—provides rack mounting and flexible easy I/O (KL-box cabling is included with the KL-box). When ordering, specify a KL-box for the KONA LH since it uses a unique cable.
• 3-year warranty
KONA LHe Audio
KONA LHe supports 2-channel 24-bit 48kHz AES audio via XLR connections, and 8 channel embedded 24 bit 48kHz audio over the same single SDI connection as the video. If you are using a digital deck—you’ll have the proper connections to the deck.
For analog audio, KONA LHe provides two-channel balanced audio input and output. If you purchase the optional KL-Box breakout box, you also get two-channel unbalanced audio output (RCA jacks).
KONA LHe also features AES input sample rate conversion; this feature eliminates the requirement for audio source synchronization. Sample rate converters auto-lock to any AES input, 32-96KHz, and then convert it to 24 bit 48KHz audio, perfectly locked to internal
KONA LHe video. Sample rate conversion is done at very high quality (over 120db THD).e
• KONA LHe control panel for source selection and controlling KONA LHe within the overall MacOS environment (Macintosh Desktop, Input Pass through, and more).
• AJA QuickTime™ drivers for tightly integrated hardware/software operation.
• Supports all popular standard definition formats: 8/10 bit uncompressed, JPEG, DV25/
50, and 3:2 pulldown for 24Hz support.
• Support for Apple Final Cut Pro™ (application software not included).
• Support for After Effects, Combustion, Motion, and Other Applications
(application software not included).
AJA’s KONA LHe software and hardware were developed for use with Final Cut Pro for powerful integrated video/audio capture, editing, and video production. With an Apple
Mac Pro, FCP, and KONA LHe, you have an ideal high-quality cost-effective system for standard definition, high definition, and analog video production workflows. Software is supplied on CD, including the KONA LHe Control Panel, drivers for the card itself, and all files necessary for Final Cut Pro and other application support (Final Cut Pro software application not included).
What’s In The Box?
When you unpack your AJA KONA LHe, you’ll find the following components:
• AJA KONA LHe Software and Documentation CD-ROM—this CD contains the software installer to place KONA LHe drivers and the Control Panel on an Apple Power Mac.
Install the software as discussed in this manual in Chapter 3: Installation and
KONA LHe Installation and Operation Manual — What’s In The Box?
Configuration. The CD also contains a wide variety of useful information, including this manual you’re reading (PDF format).
• KONA LHe PCI Express card.
• Cable, KONA LHe Standard Breakout, with Analog video, audio, AES, Reference
Input, and RS-422 Machine Control. SD-SDI and HD-SDI In/Out connectors are on the LHe card itself.
• Read Me First Notice—Contains late-breaking news and/or errata related to KONA
LHe and the documentation.
• Registration Sheet—allows you to register your card by mail or online (details provided).
Please save all packaging for shipping the KONA LHe should you wish to do so when moving or sending it in for service.
1
3
AJA KONA LH or
LHe Card
(KONA LH shown)
Installation Software CD
Read Me First Notice and Registration Sheets
Installation and Operation Manual in electronic form on the CD (PDF)
Standard Cable
KONA LH Breakout Cable
KONA LHe Shipping Box Contents
4
System Requirements
AJA Video recommends that your system meet minimum hardware and software requirements to achieve a satisfactory level of performance when operating it. Here, we provide minimum and recommended requirements and then discuss disk storage issues that should be understood for proper system configuration.
Minimum and
Recommended
System and
Software
Requirements
Item
The following table outlines the system hardware and software needed.
Recommended
Recommended Kona Driver for
Mac OSX and Final Cut Pro:
Note: always consult the release notes for the AJA software version you are running (included with installer)
FCP 7.0.x - KONA driver version 9.0.1 (Snow Leopard and
Leopard OS compatible version)
FCP 7.0.x - KONA driver version 7.5.1 (Snow Leopard and
Leopard OS compatible version)
FCP 7.0.x - KONA driver version 7.1 (Snow Leopard and
Leopard OS compatible version)
FCP 7.0.x - KONA driver version 7.0 (Snow Leopard and
Leopard OS compatible version)
FCP 7.0.x - KONA driver version 6.5 (Leopard OS compatible version)
FCP 6.0.x - KONA driver version 6.0.3 (Leopard and Tiger OS compatible version)
For the latest appropriate match for your software and hardware, visit: http://www.aja.com/support/konaNEW/kona-lhe-lh.php
Macintosh Tower:
Internal Storage (SATA inside
Mac):
Recommended KONA LHe System: Apple Mac Pro with
Dual-Core Intel Xeon Processors (2 GHz or better) with a minimum of 2GB RAM for uncompressed SD or 4GB RAM for uncompressed HD. Use a Fibre Channel or SCSI external
RAID for uncompressed SD/HD storage.
Minimum KONA LHe System: Power Mac G5 (dual) PCI-
Express, 2GHz with 2GB RAM minimum for uncompressed SD or 4GB RAM for uncompressed HD. Ensure your Macintosh has a PCI-Express slot for compatibility. Use a Fibre Channel or SCSI external RAID for uncompressed SD/HD storage.
Slot Placement: Visit our website and view this regularly updated slot placement document: http://www.aja.com/support/kona/kona-systemconfiguration.php
Best suited for compressed SD/HD formats only
External Storage:
Note: see Storage Methods topic that follows later in this
Chapter
Ideally a RAID configuration with Fibre Channel or SCSI connection to the Mac via qualified host bus adapter
Understanding Disk
Storage Methods
KONA LHe Installation and Operation Manual — System Requirements
The KONA LHe card, an Apple Power Mac, and Final Cut Pro, together offer an unprecedented level of features and performance for all Video/Audio production applications. However, to ensure performance and quality, the disk storage system used with the Apple Power Mac must be able to meet the demands of storing realtime uncompressed media. At the very minimum, the disk storage system must be able to provide and maintain a consistent 50 MB/s transfer rate from the Power Mac to disk (read/write). There are a variety of system configurations and peripherals that can provide this level of performance. Possible system configurations are listed following:
Storage Method Features/Limitations Cost
Xserve RAID
External ATA/IDE or SCSI
RAID
Features up to 14 ATA/100 drive channels, dual independent RAID controllers, and a dual 2Gb Fibre Channel host interface. Xserve provides up to 5.6TB of storage with throughput of up to 400 megabytes per second.
Expensive, although
1 gigabyte is excellent when large storage is needed
Scalable. Performance almost as good as Xserve, although it can be more complex to set up and maintain. Many vendors offer solutions (too many to list here; check with your Apple dealer for SCSI Storage solutions for details). Although the connection to the external
RAID chassis is SCSI, the drives themselves may be
SCSI or ATA. A pure SCSI array will offer higher performance at a higher cost.
Moderately
Expensive
5
About RAIDs
Redundant Array of Independent Disks, or RAID, is a group of hard drives that appears to the host Power Mac as a single high-speed storage unit. RAID systems enable you to increase storage capacity and get the performance, reliability, and data protection needed for video production, but not possible from a single hard drive. RAID drives inside the array operate simultaneously, increasing overall throughput. RAID technology is comprised of these techniques (some or all):
• Striping data across multiple drives for storage performance (RAID 0).
• Mirroring for redundancy (RAID 1).
• Parity for data protection (RAID 5 [plus others]).
Most RAID configurations, or RAID levels, combine these to provide a balance of protection and performance.
Striping divides a logical drive into data blocks, or stripes, that are distributed across an array of physical drives. Striping a set of disks improves storage performance because each drive operates concurrently. However, striping alone, known as RAID level 0, offers no data protection.
Mirroring involves writing identical copies of all data to a pair of physical drives. This results in very high data reliability: If one drive fails, the data is still available on the remaining disk drive.
However, it also results in a storage efficiency of only 50 percent, because two physical drives are required to achieve a single drive’s capacity. Mirroring alone is known as RAID level 1.
Parity provides data protection without requiring complete duplication of the drive contents. In the event of a drive failure, parity information can be used with data on surviving drives to reconstruct the contents of a failed drive. Parity data can be stored on a dedicated drive, as in
6
RAID 3, or distributed across an array of drives, as in RAID 5. Parity provides much greater storage efficiency than mirroring—up to 85 percent for a set of seven drives.
Software For Striping
AJA recommends the Disk Utility software provided by Apple with OS X for creating and striping RAIDs, including 3rd-party, SCSI, and Xserve RAIDs. It is very easy to use and has been tested to work well. The utility can be found in Macintosh HD/Applications/Utilities, where
“Macintosh HD” is the name of the system drive.
Storage capacity
No matter which storage system you choose, pick one that can scale to meet your needs over time. Ideally, you should be able to increase storage capacity or switch to a RAID level offering increased data protection in the future. Balance current and future storage needs with your budget and choose accordingly.
FORMAT
10 bit Uncompressed
Standard Definition
8 bit Uncompressed
Standard Definition
DV50 Standard Definition
DV25 Standard Definition
Photo JPEG
Standard Definition
8-bit Uncompressed 1080i
@59.94/60Hz
10-bit Uncompressed
[email protected]/60Hz
124
166
8-bit Uncompressed 1080i @50Hz 104
10-bit Uncompressed
1080i@50Hz
138
21
6.3
3.1
2.5
Transfer Rate in
MB/sec
28
Storage
Requirement in
GB/Hour
101
76
23
11
9
448
597
373
498
Hours of Storage
Per Terabyte of
Disk
9.9
13.1
43.4
90.0
111
2.2
1.7
2.7
2.0
8-bit Uncompressed
[email protected]/24Hz
10-bit Uncompressed
[email protected]/24Hz
100
133
8-bit Uncompressed [email protected]/
60Hz
10-bit Uncompressed
[email protected]/60Hz
100
133
358
478
358
478
2.8
2.1
2.8
2.1
DVCPRO HD 12.5
45 22.2
MB = MegaBytes
GB = GigaBytes for uncompressed formats, PAL and NTSC transfer rates and storage requirements are about the same because PAL has a lower frame rate, but more lines.
KONA LHe Installation and Operation Manual — Cable Connections
Cable Connections
Using the Breakout
Cable and 3 BNCs
KONA LHe offers unsurpassed cable connectivity for a video/audio capture card. Connections are made via a supplied breakout cable and three BNCs on the KONA LHe Card endplate.
The breakout cable supports:
• Reference Input (BNC)
• Component/Composite/S Video Input (3x BNC)
• Component/Composite/S Video Output (3x BNC)
• AES In (2x XLR)
• AES Out (2x XLR)
• Balanced Audio In (2x XLR)
• Balanced Audio Out (2x XLR)
• RS-422 Machine Control (9 pin D)
The three BNCs on the KONA LH Card endplate additionally provide:
• Standard and High-definition SDI input (BNC)
• 2 SDI outputs (2x BNC, independent outputs)
60-pin connector
To KONA LH
1
7
Using KL-box
SD-SDI/HD-SDI
Video/Audio
SDI Input BNC
SDI Output 1 BNC
SDI Output 2 BNC
Reference Input BNC
Balanced Audio
Analog Audio
Channel 1 Input
Analog Audio
Channel 2 Input
Analog Audio
Channel 1 Output
Analog Audio
Channel 2 Output
AES Input
Channels 1 & 2
AES Output
Channels 1 & 2
KONA LHe Breakout Cable
Analog Video green blue red green blue red
Y/CVBS In BNC
Pb/Y In BNC
Pr/C In BNC
Y/G/CVBS Out BNC
Pb/B/Y Out BNC
Pr/R/C Out BNC
6 BNCs (Analog Connections):
Can be Configured for
Component,
Composite, or Y/C
RS422
Machine Control to VTR
(9-pin)
The KL-box attaches to the KONA LHe card via cables that attach to the back of the KL-box.
These cables are supplied with the KL-Box (one 60-pin to 60-pin, and one 3-BNC to 3-BNC).
When you purchase the optional KL-Box, you get two-channel unbalanced audio output (2 RCA
Jacks)—not available with the standard cable.
8
Balanced Audio In
Channels 1 & 2
Note: When ordering a KL-Box, ensure that you specify one configured for the KONA LHe.
The KL-Box is also available for the KONA LS and LSe, but uses a different cable set when ordered for the LS card. Separate AJA part numbers exist for each configuration, so ensure your dealer supplies you with the correct one.
Serial
Digital
In
AES/EBU Audio
In and Out
Composite/
Component
Video In
RS422
Machine
Control
About BNC
Connectors
Balanced Audio Out
Channels 1 & 2 Serial
Digital
Out
External
Reference
(loop)
Composite/
Component
Video Out
Analog Audio
Output
AJA KL-box Panel Connectors
Although most video professionals are used to BNC connectors, you may not have seen them if you’ve been using primarily desktop video equipment. BNC connectors ensure a positive connection by the act of locking the connectors together via pins in one connector that fit into slots in the corresponding connector.
To make a BNC connection, slide the cable connector over the panel connector and then when seated, rotate the barrel of the cable connector 90˚ clockwise until the connectors are locked together. When properly locked, the cable cannot accidentally be pulled out.
Pins (2) on BNC Connector
(connector on KL-box)
Align slots in cable connector barrel with connector pins, then slide it over the pins and rotate the barrel to lock the connectors together
Connector
Descriptions—
Cables and KL-box
Connectors on the standard cable set are labelled as to their function for easy installation and maintenance. Similarly, connectors on the optional KL-box are also labelled.
SDI Input and Outputs
BNC connectors are provided on the KONA LH card endplate for one SD-SDI or HD-SDI input and two SDI outputs (independent of the input). The SDI input and outputs support video and embedded 24-bit digital audio. Use SDI wherever possible for the best quality 10-bit uncompressed video input, capture and output. If peripheral equipment has a variety of
KONA LHe Installation and Operation Manual — Cable Connections
inputs/outputs, look to see if it has SDI I/O, and use it where possible. Most high-end professional broadcast equipment supports SDI (VTRs, cameras, media storage servers, etc.).
2 Channel Digital AES/EBU Audio Inputs And Outputs
One female XLR connector is provided for the channel 1 and 2 inputs, while a male XLR connector carries channel 1 and 2 outputs. AES/EBU signals are handled internally as 24-bit digital.The optional KL-box also provides XLR audio connections on the front panel.
Note: AES XLR connections are digital and cannot be used with analog equipment having XLR connectors.
Analog 2 Channel Balanced Audio
1
Male XLRs are provided for outputs and female XLRs are provided for inputs. Balanced audio
(differential) connections provide better analog audio quality over longer cable runs. Most professional quality VTRs and audio equipment have XLR style connectors for analog audio.
Analog audio signals are converted internally to 24-bit digital.
Analog 2 Channel Unbalanced Audio (KL-box only)
On the KL-box are two analog output connectors, one for each channel. These connectors are
RCA-style phono jacks.
9
RS422 Machine Control
A female DB9 connector on the breakout cable provides connection for VTRs, camcorders, disk media servers, and other devices using RS422 SMPTE (Sony) protocol. This connector is also present on the optional KL-box. (Connector pinout is listed in Appendix A: Specifications.)
Analog Monitor Out (Component/Composite HD/SD)
Both the standard I/O cable and the optional KL-Box feature two groups of 3 BNC connectors
(each) for input and output of component, composite and Y/C functions. The signals are labelled on both the cable and KL-Box connectors.
Component video signals are generally higher quality than composite, but not as high quality as serial digital (SDI).
A Note About RGB —Although RGB is used less in today’s video systems, KONA LHe supports it. However, because the KONA LHe (and SMPTE SDI) native format is YPbPr, AJA recommends the use of YPbPr whenever possible for analog monitoring. Although component video monitors often have RGB inputs, it’s better to use YPbPr when the monitor supports it. The YPbPr format provides “headroom” for “superwhite” and
“superblack”—and these video levels will be clipped when transcoding to RGB. Also, the
RGB/YPbPr transcoding involves a level translation that results in mathematical round-off error. RGB can be configured in the KONA LH Control Panel.
A Note About YPbPr —Component Video, or YPbPr, has been given several names over time.
YUV, Y/R-Y/B-Y, and YCbCr, are just some examples. Although these various formats have some differences in levels, they are all basically the same. KONA LHe uses the modern
YPbPr terminology exclusively. KONA LH supports three different types of YPbPr: SMPTE/
EBU N10, Betacam (NTSC), and Betacam (NTSC Japan). These three formats differ in level only and are configured in the KONA LHe Control Panel.
Reference Video
A single BNC on the standard KONA LHe cable—or two BNC connectors on KL-box (it loops through)—allow you to synchronize KONA LH outputs to your house analog reference video signal (or black burst). If you have a sync generator or central piece of video equipment to use for synchronizing other video equipment in your studio, then connect its analog composite output here. When KONA LHe outputs video it uses this reference signal to lock to. When connecting a reference video source, the locking signal should be the same format as the
10
In This Manual
Primary format selected in the KONA LHe Control Panel. It is possible in some circumstances to use an alternate format video signal as long as the basic frame rate is compatible.
Chapter 1 is the introduction you’re reading, listing features, box contents, and system requirements.
Chapter 2 gets you started with using KONA LHe in a typical Video environment. Typical workflows are discussed.
Chapter 3 provides complete instructions for installing and configuring the AJA KONA LHe card. The user is guided through unpacking, installing the card into a PowerMac, installing
KONA LHe Mac Software From CD, cabling the system and then getting it up and running.
Important configuration information is also provided on video settings and use of genlock/ external reference.
Chapter 4 discusses operational aspects of KONA LHe when used with Final Cut Pro.
Chapter 5 discusses troubleshooting problems with your system and what to do when there’s a problem you can’t solve.
Appendix A presents a list of technical specifications for the product.
The remainder of the manual consists of appendices listing specifications and an index section to help you rapidly find topics in the manual.
Chapter 2: Getting Started
KONA LHe And Your Workflow
There are a lot of ways to think about the video/audio workflow you follow. Your setup might be categorized as corporate video, professional broadcast, or desktop video. Or the workflow might be categorized by the type of equipment used rather than the nature of work produced—many systems these days are a mixture of equipment from high-end professional to desktop video. This chapter hopes to show how Final Cut Pro and KONA LHe can help fit into whatever workflow you currently have and make it more efficient.
A Workflow Scenarios diagram on the following page shows types of equipment, sorted by
VTR source, and the types of workflow attributes and KONA LHe applications supported. After the diagram, we also discuss some typical applications.
Source Deck Type(s)
Digital SD-SDI or HD-SDI
Examples: Digibeta, DV50, DVCPRO HD,
HD Varicam and DVcam
Analog
Examples: Beta, VHS, and U-matic
Digital capture via Firewire with Output via AJA
KONA LHe. The LHe has Analog HD component in,
which also allows you to bring in HD directly from
an HDV camera head.
Example: MiniDV, HDV
Without even using a deck; use the video monitor
as a second Mac monitor. The KONA LHe
desktop lets you drag graphics from
programs like Adobe Photoshop from
the computer display to the video monitor. You
paint full frame and live onto a broadcast monitor.
Output virtually anything to video—ideal for
animators and compositors.
Workflow Scenarios
Workflow Attributes
KONA LHe captures and outputs
SD-SDI/HD-SDI video with embedded audio. Use high-quality AES/EBU and/or embedded 8-channel audio output.
KONA LHe captures and outputs
Y/C, Component, and Composite
Video, with 2-channel audio.
Applications
Pro Broadcast
Corporate/Industrial
On-site Editing
Corporate/Industrial
Pro Broadcast
On-site Editing
Using standard desktop video techniques, video/audio is captured directly from a camcorder or deck.
KONA LHe is used for playing back captured media and editing/mastering to tape or DVD using Final Cut 5 HD and other tools such as After Effects,
Combustion, Apple Motion, etc.
HDV playback is aided by KONA LHe onboard hardware scalar.
Desktop Video
Corporate/Industrial
On-site Editing
Pro Broadcast
Using Final Cut Pro, work with a wide range of old and new SD and analog sources, and then also using desktop graphics and video software for creative power and flexibility.
Post-production
Animation
Compositing
2
1 1
12
Understanding Typical Workflows
KONA LHe and Final Cut Pro allow more workflow flexibility than ever before. Users can independently select different formats for capture and storage media, while also outputting to an array of analog and digital uncompressed formats—with all outputs active simultaneously. Capture can range from analog, DV, or SD and HD digital uncompressed.
Media can be stored on disk as:
• offline quality at low bit rates
• on-line quality at moderate bit rates
• or with the highest quality as 8 or 10 bit uncompressed SD and HD
As quality and codecs improve, the lines between offline and online are blurring. For example, with the Apple ProRes 422 codec, native HD editing in that codec is now possible, providing very high quality results (true HD editing) at very low data rates.
Following are summaries of the most common workflows, listing data rates and relative quality levels. Some workflows require a RAID array and some will work using the host Mac’s internal system drive—it’s noted where this is supported in the following discussions.
PhotoJPEG
Data rate: approximately 1-3 MB/second standard definition or high definition—supported by internal system drive
Quality: Very Good
The Apple PhotoJPEG codec offers an excellent compressed media choice for on-line quality at low data rates. PhotoJPEG can use the full-raster at 4:2:2 sampling. Final Cut Pro allows you to adjust quality using a PhotoJPEG control panel. KONA LHe allows for
PhotoJPEG monitoring and/or output in both SD and HD. KONA LHe can capture from almost any HD or SD input, directly to PhotoJPEG media.
DV (DV25)
Data rate: 3.13 MB/second (megabyte/second) standard definition only—supported by internal system drive
Quality: Good
In this workflow, DV is usually input to a Mac Pro running Final Cut Pro through its FireWire port. DV offers good quality, but it has lower Chroma resolution when compared to DV50,
JPEG, or uncompressed. You can use KONA LHe to convert DV projects to uncompressed— in real time—for monitoring and/or output. Alternatively, KONA LHe can capture uncompressed from any input, directly to DV media.
DV50
Data rate: 6.26 MB/second standard definition only—supported by internal system drive
Quality: Very Good
Like DV25, Final Cut Pro also supports the Panasonic DV50 standard definition codec. DV50 is a 4:2:2 compressed format and therefore has higher chroma resolution when compared to DV25. Also like DV25, you can use KONA LHe to convert DV50 projects to uncompressed—in real time—for monitoring and/or output. KONA LHe can capture uncompressed from any input, directly to DV50 media.
DVCPRO HD
Data rate: 12 MB/second high definition—supported by internal system drive
Quality: Excellent
Like DV50, Final Cut Pro also supports the Panasonic DVCPRO HD high definition codec. You can use KONA LHe to convert DVCPRO HD projects to uncompressed—in real time—for monitoring and/or output. KONA LHe can capture uncompressed from any input, directly to DVCPRO HD media. When playing the DVCPRO HD format back, the KONA LHe hardware handles the work of properly scaling the video for monitoring and output—which provides for more streams of RT effects, since the Mac processors are freed up to handle the RT.
HDV
KONA LHe Installation and Operation Manual — Understanding Typical
Data rate: 19 MB/second high definition720p, 25 MB/second high definition 1080i— supported by internal system drive
Quality: Excellent
KONA LHe supports and accelerates the Final Cut Pro HDV Codec. You can use KONA LHe to convert HDV projects to uncompressed—in real time—for monitoring and/or output.
KONA LHe can capture uncompressed from any input, directly to HDV media. The KONA
LHe advanced scaling engine takes the native frame (long GOP 1440 HD) and outputs it via hardware—in real time. Precision AJA circuitry re-sizes the video to proper 1920 x
1080, providing quick playback of HDV captured by Final Cut for monitoring and recording.
HDV captures HD images via MPEG2 compression and allows for recording the signal to a
MiniDV tape. This MPEG2 compression is similar to a DVD (although DVD is a program
1 variable bit rates). The issue for post production is that the HDV transport stream is based around a long-GOP structure (group of pictures) which produces images based on information over a section of time, via I, P and B frames; Intraframes, predicted frames and bi-directional frames. Formats that do not use this scheme treat frames as individual units, as in the progressive formats where a frame truly is a frame, or as interlaced frames where two fields create the image. Sometimes we refer to these formats in contrast to
MPEG formats, as I-frame formats where frames can be easily defined as individual.
Since the frames of HDV have the long GOP structure to define them, herein lies the problem for post-production; how can we work with the material if we must know what lies before, after and during? Luckily, the transport stream MPEG2 can be transmitted over IEEE1394 (aka FireWire). This means that the compressed HD material can be transferred into systems with the appropriate hardware and software (for example, a Mac
Pro with Final Cut Studio 2). While this seems like a simple solution for post-production, it means that the footage must be brought into the system as a rather heavily compressed format and that the computer must continue to work with the material as a
MPEG2 transport stream, which is incredibly processor intensive for the computer.
How does the AJA KONA LHe card connect to HDV and digitize material to uncompressed
HD files for editing—or at the very least, to a lightly compressed I-Frame HD format? The answer to this is provided in a feature common to many HDV devices: analog HD output via component video. The component connectors on JVC cameras and decks, along with
Sony cameras and decks, allows for the output of the long GOP MPEG2 data as a standard
HD video format such as 720P in the JVC products—or 1080i in the Sony products.
Since the KONA LHe has the ability to digitize analog HD signals, the analog component output of the HDV devices can simply be connected to the KONA inputs. Note that HD signal cannot be transported over composite or S-Video (Y/C) cables, so the HDV device must have an analog component HD output. The KONA LHe also has the ability to ingest analog audio, so the analog audio outputs of the HDV devices can be sent to the KONA card as well. (Also note that these analog audio outputs on the HDV devices are usually unbalanced RCA connections where the KONA card uses balanced XLR style connection so some sort of audio level correction device, such as a mixer or a stand alone active interface amplifier, should be used for accurately attenuated audio.)
Finally, you will want to control your device. Where all of the video, audio and timecode information moved over the FireWire cable, now you are dividing those tasks. Device control is the most difficult to configure for HDV devices because so few HDV devices have implemented any form of device control other than IEEE1394. The one notable exception is the JVC BR-HD50 HDV deck which has a remote serial port for RS422 protocol and device control. Check the KONA LHe support area on the AJA website for a whitepaper on HDV, which gives details on using KONA LHe with various HDV equipment.
Note: direct capture into HDV media on the LHe is not possible. Direct capture into the
LHe can only be done using uncompressed, DVCPRO HD, or Pro Res. Regarding
ProRes 422, capturing HD resolution ProRes 422 from an HD source requires a Mac
Pro with an Intel Xeon processor.
13
14
Apple ProRes 422 and Apple ProRes
422 HQ
(SD or HD)
Uncompressed
8-bit
Uncompressed
10-bit
Data rate: Approximately 18 MB/second ProRes 422, Approximately 31 MB/second ProRes
422 HQ— supported by internal system drive or attached storage
Quality: Excellent, broadcast quality
Captured media is virtually indistinguishable from pristine uncompressed sources. Better yet, ProRes maintains the quality during editing, surviving multiple encoding/decoding generations without degradation. It was designed by Apple for editing, rather than as a transmission/distribution codec as are most popular codecs. Some of the advantages include:
• Full-size 1920-by-1080 and 1280-by-720 HD resolutions.
• Full-size 720-by-486 and 720-by-576 SD resolutions.
• 4:2:2 chroma sampling. Provides precise compositing and blending at sharp saturatedcolor boundaries.
• 10-bit sample depth. Preserves subtle gradients of 10-bit sources (perfect for greenscreen compositing, graphics or color correction) with no visible banding artifacts.
• I frame-only encoding. Ensures consistent quality in every frame and no artifacts from complex motion.
• Variable bit-rate (VBR) encoding. “Smart” encoding analyzes the image and allocates more bits to complex frames.
• Low data rate requirements make for more storage options and require less drive space to store high quality video.
Data rate: 21 MB/second standard definition, or 100-124 MB/second high definition (see later “Storage Capacity” chart in Chapter 1 for the various transfer rates per format)— requires SCSI, Fibre Channel, or ATA drive array
Quality: Excellent
Uncompressed media is KONA LHe’s native storage format, offering the highest quality available. Capturing in uncompressed results in no compression artifacts, and video is sampled over the full raster at a 4:2:2 rate.
Using uncompressed maintains a higher quality in your project from capture all the way through effects rendering. Final Cut Pro supports RT with uncompressed media using RT
Extreme. KONA LHe supports capture of uncompressed through any of its inputs, and uncompressed projects are output to all of its outputs simultaneously.
Data rate: 28 MB/second standard definition, or 133-166 MB/second high definition— uncompressed 10-bit requires SCSI, Fibre Channel or SATA drive arrays.
Quality: Excellent, very high quality
Offering all the benefits noted previously for 8-bit uncompressed, 10-bit additionally offers the very highest quality available. With 10-bit media and Final Cut Pro’s 32 bit Floating Point
YUV Codec, video quality is second to none. For more information on this subject, please see the topic at the end of Chapter 4: Installation and Configuration, titled “Using 8-bit Versus
10-bit Video.”
KONA LHe Installation and Operation Manual — Mixing and Matching
Mixing and Matching Formats in Final Cut
In Final Cut Pro, it works best to use one format consistently. For example, if you capture DV 50 files and then capture 8-bit uncompressed files, you’ll have to rerender one or the other when using the two types on the same Final Cut sequence (the timeline where media is edited into a project). You could even capture 8-bit uncompressed and HDV, and then place them both on a
PhotoJPEG timeline and end up having to render them both. You can capture directly, in real time to any supported format, even if it doesn’t match the source formats at all (for example, DV and DV50 to 8 bit uncompressed).
Therefore, it makes sense to capture media into your system at the highest quality you’ll expect to use to eliminate rerendering and ensure best results. KONA LHe is ideal for this since it has the connections necessary to bring in a variety of media for capture into Final Cut.
1
15
16
Chapter 3: Installation & Configuration
Installation Overview
The installation and set up of a KONA LHe is very simple. All of the steps of installation and configuration are documented in this chapter, summarized as follows:
1. Unpack the shipping box
2. If not previously installed on your Mac Pro, ensure that Final Cut Pro is installed as detailed in its user documentation. Final Cut Pro must be installed and have been run at least once prior to installing AJA KONA LHe software.
3. For Mac Pro and LHe:
Visit: http://www.aja.com/support/kona/kona-system-configuration.php
Locate your Mac model and install in the recommended slot.
For Model LHe and a G5:
Lay the PCIe PowerMac G5 on it’s on it’s side (motherboard facing up). Install the KONA
LHe capture card into one of the PCI Express slots in the PowerMac. The RAID controller card (SCSI or Fibre Channel) can go in any other available slot.
4. Install AJA KONA LHe software on your Mac from the supplied AJA CD-ROM
5. Cable the system audio and video sources, VTR, audio monitor, and video monitor. If you purchased the optional KL-box, then install it into an equipment rack or place it on a desk and connect its two cables to the KONA LHe card. If you’re instead using the standard cable set, then use those to connect equipment.
Each of these steps are explained in greater detail in the remaining pages of this chapter.
Unpacking
Shipping Box
Contents
KONA LHe is shipped with a CD containing system software and an Installation and User manual (a PDF on the CD), and a cable. If you purchased the optional KL-box breakout box, it ships with its own set of cables and instructions for connection to the KONA LHe card.
3
1 1
18
AJA KONA LH or
LHe Card
(KONA LH shown)
Installation Software CD
Read Me First Notice and Registration Sheets
Installation and Operation Manual in electronic form on the CD (PDF)
Standard Cable
KONA LH Breakout Cable
Contents, KONA LHe Shipping Box
As you unpack the shipping box(es), carefully examine the contents. Ensure you received everything and that nothing was damaged during shipment. If you find any damage, immediately notify the shipping service and supply them with a complete description of the damage. AJA will repair or replace damaged items. If you find shipping damage, contact your AJA dealer or distributor for details on how to have your KONA LHe repaired or replaced.
Note: Save packing materials and the shipping box. If you ever require service or move your system—use the packaging materials and box for safe shipment.
KONA LHe Installation and Operation Manual — Installing the KONA LHe
19
Installing the KONA LHe Card in a Mac Pro
1. Place the Mac Pro in a well-lit convenient area, where you will have easy access to the chassis access door.
2. Using your hand, touch the outside of the Mac Pro to discharge any static electricity you have. Remove the power cable from the back of the Mac.
3. Remove the access door as described in your Apple User Manual. Lay the Mac on its side, motherboard facing up.
4. Remove the KONA LHe card from its protective anti-static bag; place the card on top of the bag.
5. Visually locate the PCIe slots inside the Mac chassis. The slots are numbered along the left side. Visit: 1
http://www.aja.com/support/kona/kona-system-configuration.php
....and determine which slot works best for your Mac Pro model. This page is updated regularly to account for Apple product line changes.
6. Remove the card edge locking plate on the right side of the card cage, using a
Phillips screwdriver (it is held in place by two captive phillips screws).
7. Carefully insert the KONA LHe card by rocking it slowly into the desired PCIe slot.
Ensure the card edge aligns properly with the Mac Pro’s rear panel opening (where the card edge locking plate was just removed) and that it is fully seated in the slot.
8. Replace the card edge locking plate removed earlier, securing the two phillips screws.
9. Replace the Mac Pro’s access door.
KONA LHe Card
20
Installing the KONA LHe Card in a G5
1. Place the PCI-Express G5 in a well-lit convenient area, where you will have easy access to the chassis access door.
2. Using your hand, touch the outside of the G5 to discharge any static electricity you have. Remove the power cable from the back of the PowerMac G5.
3. Remove the access door and clear inner panel as described in your Apple G5 User
Manual. Lay the G5 on its side, motherboard facing up.
4. Remove the KONA LHe card from its protective anti-static bag; place the card on top of the bag.
5. Visually locate the PCI-Express slots inside the G5 chassis. The KONA card only requires a 4-lane PCI-Express slot, so any of the available slots will work correctly.
6. Remove the card edge access cover from the desired slot where you will be inserting the KONA LHe card. The card edge cover is secured by a phillips screw; save this screw for use in installing KONA LHe.
7. Holding the KONA LHe card by the card edge plate and an outside edge, carefully insert the KONA LHe card by rocking it slowly into the slot. Ensure the card edge aligns properly with the G5’s opening (where the card edge cover was just removed) and that it is fully seated in the slot.
8. Secure the card in the slot using the screw removed earlier.
9. Replace the G5’s clear inner panel and outer access door.
Note: After you install the KONA LHe card, you may notice that in the MacOSX Network preferences there is a message stating “You have a new network port named KONA LHe
—be sure to check the settings...”. There is no need to take any action; this occurs because MacOSX detects the RS-422 serial port on the KONA LHe card that you will use for VTR machine control.
KONA LHe Installation and Operation Manual — Cabling the System
21
Cabling the System
System Video/
Audio Cable
Connections
When installing your system, you’ll make video and audio input/output connections. These connectors are explained individually in chapter 2. Here, system interconnection is shown and described.
System Cabling When Using The Breakout Cable
1
KONA LHe
Installs in
PCI-Express Slot in G5
KONA LH
Installs in
PCI-X slot in G5
Standard Breakout Cable
60-pin connector
To KONA LHe
Reference Input BNC
Balanced Audio
Analog Audio
Channel 1 Input
Analog Audio
Channel 2 Input
Analog Audio
Channel 1 Output
Analog Audio
Channel 2 Output
AES Input
Channels 1 & 2
AES Output
Channels 1 & 2
SD-SDI/HD-SDI
Video/Audio
SDI Input BNC
SDI Output 1 BNC
SDI Output 2 BNC
Analog Video green blue red green blue red
Y/CVBS In BNC
Pb/Y In BNC
Pr/C In BNC
Y/G/CVBS Out BNC
Pb/B/Y Out BNC
Pr/R/C Out BNC
6 BNCs (Analog Connections):
Can be Configured for
Component,
Composite, or Y/C
RS422
Machine Control to VTR
(9-pin)
KONA LHe System Using The Breakout Cable
22
Typical System
A figure on the following page shows typical system interconnections for a system with digital
A/V sources. Your system may differ depending on VTRs, audio monitoring, and video monitoring.
1. If desired, connect your house reference sync to the KONA LHe Ref Loop connector
(BNC). The second KONA LH Ref Loop connector on the KL-box (if used) can be connected to the VTR or terminated with a 75-ohm terminator.
2. Connect a Video Monitor to the KONA LHe Component Analog Video Out BNC connectors (preferred), or instead connect to a composite monitor.
3. Connect a 9-pin DB9 machine control cable between your VTR’s RS422 control port and the breakout cable’s RS-422 machine control connector.
4. Connect two SDI cables between KONA LHe (BNCs are on the card endplate) and your digital VTR (Digital Betacam etc.): one from KONA LH SDI In to the VTR SDI Out, and one from KONA LHe SDI Out (1 or 2) to the VTR SDI In. The KONA LHe SDI connections have embedded audio so the VTR must be configured accordingly.
5. If you have an AES/EBU-ready audio monitoring system, then connect the two channels of AES/EBU output from KONA LHe’s XLR connectors (channels 1 and 2) to the monitoring system AES/EBU inputs. If you instead have an analog audio monitoring system, you can use either the XLR balanced audio connectors or the two RCA-style unbalanced stereo output jacks on the Optional KL-box for output.
Digital VTR with SDI Inputs
Analog Audio
Inputs/Outputs
(Balanced)
Reference Monitors
SDI Video with Embedded
Audio In/Out
RS422
Machine
Control
Connect to
KL-Box Using
Cables and Instructions
Supplied With it
AJA KONA LHe Card
Installed
Inside Mac
External Reference
Optional
Genlock
Reference
Video Monitor
Component
Video
Computer Monitor
POWER
CMPTR
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Dual-port 2Gb Apple Fibre Channel PCIe card
Apple Mac Pro w/OSX
And
Final Cut
Pro
Typical System Connections—Shown with Optional KL-Box
KONA LHe Installation and Operation Manual — Installing KONA LHe
Installing KONA LHe Software
First ensure that Final Cut Pro is installed as detailed in its user documentation. Final Cut Pro must
be installed and have been run at least once prior to installing AJA KONA LHe software. Next, use the
CD-ROM supplied with the KONA LHe system to install necessary software drivers and KONA LHe control panel. You cannot use KONA LHe with Final Cut Pro until the AJA KONA LHe software has been installed on the host Power Mac.
System software updates may occasionally become available to AJA KONA LHe owners on our website (www.aja.com). We recommend checking occasionally for both software updates and additional product information.
Note: If your Mac has previously had another video capture or multimedia card installed, ensure you remove the card and uninstall any related software before installing KONA LHe. This will
1 also has an AJA Io installed, but not an Io HD.
23
Software
Installation
Procedure
Locate the AJA KONA LHe Software CD packaged with your system. Then follow the procedure below to put the required software on the host system to be used with KONA LH/LHe. The system must be an Apple Mac Pro or Power Mac G5 as described earlier in Chapter 1: System Requirements.
Note: Before installing KONA LHe software, turn off any virus protection and security software that you may have installed on your computer.
1. Insert the KONA LHe CD in the Mac
2. Locate the KONA LHe CD icon on the OS X desktop.
3. Move the mouse cursor to the icon and double click to see the CD contents, which will appear in its own window.
4. In the window, locate the package file; it has an icon that looks like a box and has a “.pkg” or
“.mpkg” suffix.
Note: Files ending in the “.pkg” and “.mpkg” suffix are OS X installer files. These launch the OS X installer and tell it where and what to install on your system.
5. Double-click the package to log on and begin software installation.
6. The system will respond by asking you to authenticate who you are as currently defined on your OS X user profile. Enter the proper name and password at the Authenticate prompt; if you have multiple users defined, ensure that you log on as a user with administrator-level authority.
Log On Authenticate Prompt
7. Click on the OK button after entering a valid user and password.
24
8. The installer will launch and you’ll see a series of installer screens.
Initial Installer Screen
9. Click Continue to begin installation.
10.The next screen lets you know that the installer will check your PowerMac to ensure it has the hardware and software resources required (see Minimum Requirements in
Chapter 1).
System Check Installer Screen
11.Read and agree to the Software License Agreement.
KONA LHe Installation and Operation Manual — Installing KONA LHe
25
1
KONA LH Software License Agreement Screen
12.The next screen shows all the available drives on the Power Mac. Click on the drive that contains your system files (Apple default is “Macintosh HD”). A green arrow will point to the drive you’ve selected. Click the Continue button to proceed with installation.
Select a Destination Drive For the KONA LH Software
13.At the next screen, click the Install button to place the software on the drive you previously selected.
26
Easy Install, Installer Screen
14.A system prompt will pop up with a reminder that OS X must be restarted after installation. Click the Continue Installation button to proceed.
Restart OS X Reminder Prompt
15.The installer will run and put all the necessary KONA LHe drivers, KONA LHe Control
Panel, presets and software on the desired hard drive. When it has completed installation, a final screen will be displayed announcing that “software was successfully installed.”
KONA LHe Installation and Operation Manual — Genlock and Your System
16.Click the Restart button to complete the installation procedure. The system will perform a software restart and be ready for use.
27
1
Final Installation Screen
Genlock and Your System
For video stability and proper system operation, it’s always best to genlock all equipment to house sync. Although genlock is not absolutely required for KONA LHe or your system, better quality and repeatable operation will be experienced by doing so. Usually, this means using a black burst generator output looped through the system. On the KONA LHe cables and optional
KL-box breakout box, house sync is connected to “Ref Loop”.
28
Chapter 4: Final Cut Pro and Other Software
Final Cut Pro
Final Cut Pro (not included with KONA LHe) ships with information already configured for most common system configurations. After you install the KONA LHe software on your Mac
Pro, all you need to do to begin using it is to become familiar with the KONA LHe Control
Panel and how Final Cut Pro works with KONA LHe.
With Final Cut Pro you’ll choose the proper setups from the canned ones provided by AJA.
These canned setups are called “Easy Setups” in Final Cut Pro and are available to use and edit under Audio/Video Settings in the “Final Cut Pro” menu (next to the apple menu).
You’ll also need to gain familiarity with the KONA LHe Control Panel, which will be used for source selection, configuring many KONA LHe features, and for creating your own preset configurations for different applications.
The manual you are reading does not provide operational information about Final Cut Pro.
Please read the Final Cut Pro user documentation provided with it for information on configuration and operation. The chapter you are reading addresses configuration and setup unique to use of KONA LHe with Final Cut Pro and other applications.
Using The KONA LHe Control Panel
The KONA LHe Control Panel is a software application that provides a simple visual way to see how the KONA LHe card is currently configured and then make changes as desired. Settings— both what you changed and didn’t—can be saved as a snapshot for recall at anytime. This lets you save settings associated with all your frequent tasks; then as you switch tasks you don’t have to spend extra time constantly resetting card configurations—just load the previously saved settings for each task.
One thing you’ll notice instantly about the Control Panel is that it represents a visual block diagram of how the card is set. The current status, input and output settings, up/down/crossconversion, and many other details can be viewed as a color-coded block diagram in the
Control Panel.
Control Panel Basics
Although the KONA LHe card auto-configures depending on the inputs present, and the
Control Panel intuitively shows at a glance much about what the card is doing, there is even more information presented that may not be obvious. To ensure you make the most of the software, run the KONA LHe application and look at its display. Then refer to the “Basics” described here to fully understand what you’re seeing and learn how to view and change the
KONA LHe system configuration.
4
1 1
30
Note: The KONA Control Panel also works with other KONA cards, Io HD and Io Express.
However, the actual features and screens displayed differ slightly since the board feature sets differ.
Before we go into too much detail, here are some basic definitions you should know (please refer to the figure that follows for reference). After studying the basics, read “Who is
Controlling KONA LHe?” later in this chapter for more advanced information on how applications interact with the KONA LHe board.
Tabbed Screens—the bottom area of the AJA Control Panel provides different information categorized by topic. Clicking on one of the “Tab” items from the left navigation column will result in an information screen corresponding to that tab’s topic. Each of these tabbed windows are described on the following pages.
Tabs screens available are:
Control: configures the default output (test pattern, pass through, desktop,
etc.) plus setting genlock and output timing.
Format: select the framebuffer primary video format, any secondary.
formats, and parameters of conversion for input/output.
Input Select: view and edit input selections and how they are mapped.
Proc Amp: enable/disable Proc Amp, and edit settings or set to unity
SDI Output: assign outputs to either Primary or Secondary formats.
Analog Output: configure the component/composite +Y/C analog output.
Video Setup: configures Video options such as composite black level.
Audio Setup: configures analog audio monitor level and delay.
Conversion: used to select codec options such as whether paused video
appears as a full frame or a single field (jitter shown or not shown) and 24
to 30 fps padding patterns.
DS Keyer: select downstream keyer mode, specify a graphic file or matte.
Timecode: monitor RP-188 timecode and configure timecode window burn
output (Note: SMPTE 12M-2 is the updated name and specification for
what was RP-188)
Timelapse: enables the capture of select frames over a specified time interval.
Info: displays status information about the KONA. This information is
generally intended for troubleshooting and support.
Block Diagram Screen—the top area of the AJA Control Panel shows a visual picture representing the processing (if any) that's currently occurring, including inputs/ outputs, any downconversion, reference source, and system status. Lines between inputs, the framebuffer, and outputs, show a video path. Where there are no lines, it shows there is no connection; this can be either because an input or output isn't selected or because no video is present at the selected input.
Icon objects on the block diagram screen (input/output icons, frame buffer, etc.-also called “widgets”-indicate their status by color (explained later) and when clicked will bring up the proper tabbed screen used to configure that item. For example, clicking on an SDI output icon will cause the “SDI Output” tab screen to be displayed below the block diagram. With the mouse on a block diagram element, you can also control click to reveal contextual drop down menus for certain functions.
Text Color—Colored text in the block diagram provides an indication of signal type and what the KONA LHe is doing. Text in blue shows the values automatically selected, while text in black shows values that have been manually selected. Text in red shows that the KONA is not detecting a signal or cannot negotiate with the attached device
(even if it can’t detect an output device, it still shows the signal it is outputting).
Currently
Selected
Tab Screen
KONA LHe Installation and Operation Manual — Using The KONA LHe
31
Framebuffer
Format
(“Primary Format”)
Outputs:
SDI and analog
1
Inputs
Tab Screen Choices—
Click One To Edit/View A Topic
AJA Control Panel, Block Diagram
Framebuffer—the framebuffer is the “engine” in the KONA LHe where active video operations take place using Final Cut Pro, other 3rd-party applications, or even the
KONA itself. The framebuffer has a format (called the “Primary Format” and color space that it follows, as defined in the Tabbed Windows or via external application software such as the “Easy Setups” in Final Cut).
It is important to realize that inside the Macintosh many applications can use the
KONA LHe (as you switch from window to window) and it may not always be obvious which is currently controlling it. The AJA Control Panel displays the name of the application controlling the card in red text on the Format and Control tabs of the interface. If an application does not properly “let go” of the KONA as another takes over-you'll be able to tell by looking at the Control Panel.
Primary (Framebuffer) Format—the video format currently assigned to KONA LHe. This is the format that the framebuffer will use and is shown in the Control Panel using the color blue. All icons in blue are the same as the Primary Format used by the framebuffer. Also any text descriptions in the block diagram that appear in blue also indicate that something is in the primary format. So, for example, if you see that the input and output icons are blue, then you know that the same format is used throughout the video path and that no format conversion is being performed. If a different color is displayed on the input or output, green for example, then you know that the KONA LHe is performing a format conversion in the video path.
Secondary Format—any format other than the currently selected Primary Format, is a secondary format. As described previously, this means that either the Inputs or
Outputs are somehow different from the framebuffer’s assigned format (i.e., the
“Primary Format”). This can be seen at a glance because the color will be different than blue.
32
Input/Output Icons—the input and output icons are triangles that together with their color show all the input and outputs and their status (selected, not selected, input present or not, format, etc.). A complete video path is shown when inputs and outputs are connected with lines going to/from the framebuffer.
Input/Output Icons
Conversion Icon—when an input or output is a different standard than the framebuffer then the KONA LHe may be downconverting the signal to the proper standard. This may be automatic, because it's detected an input signal that differs from the standard currently selected, or because you've explicitly told it to convert. In either case, the block diagram will show the conversion by displaying a conversion icon in between the input/output and the framebuffer.
Down Conversion Icon
If you click on a conversion icon, the Tab Screen will change to the Format scneen, allowing you to view/edit settings.
Color Meanings—all items in the AJA Control Panel block diagram are color-coded to show what is happening in realtime. This applies to both icons and text. These colors have the following corresponding meanings:
Blue: video is same format as the Primary Format (framebuffer)
Red: there is no video, the selected operation cannot be performed, or an invalid selection has been made
Yellow: reference video (black burst or other reference source)
Green: indicates that LHe is performing some kind of active change to the video, to make it different from the Primary Format (e.g., down convert).
Control Tab Screen
KONA LHe Installation and Operation Manual — Using The KONA LHe
33
The KONA LHe can be controlled by various software applications running on a host Mac as well as be used as a Macintosh Desktop extension. The Control Tab is where you select how the card directs video and is used by application software. This screen also provides control for configuring output timing with regard to external reference video and horizontal/vertical delay.
At the top of the Control screen it will show the current Default Output and the application currently controlling it (if there is one). For example, in the screen shown here, the default output is a Test Pattern.
1
AJA Control Panel, Control Tab
Control Tab Screen Settings
Default Video Output—this is where you select what the KONA LHe will output as a default when no application has control of it, such as when the Finder is active. Since it can be controlled by software applications as well as its own control panel, the output can change dynamically. Some video applications will grab control of the KONA LHe inputs/outputs. These settings determine what happens when an application is active that does not grab the KONA
LHe inputs/outputs.
AJA Control Panel, Control Tab, Default Output Pulldown Menu
Default Output Choices and their meanings:
Input Pass through: this selection directs KONA LHe to route video from its selected input through the card for processing and output. When this selection is in effect, all Primary/
Secondary Format selections are available for selection in controlling the output. This in effect makes the LHe a converter when used in conjunction with the AJA Control Panel application and a Mac.
34
No applications other than the AJA Control Panel need to be open to convert audio and video from one format to another. For example, if an SD source tape needs to be dubbed to an HD tape, the signal might be routed from the SD VTR to the LHe, configured for upconversion in the Control Panel and then passed through to the HD VTR for recording.
Test Pattern: this selection directs KONA LHe to output a choice of preset pattern when no other application is using the card. In addition to the provided test pattern choices, a
“Load File...” selection at the bottom of the menu allows you to load any standard Mac
RGB graphics file (.tif, .psd, etc.) into the frame buffer for display.
Note: The graphic file will not be scaled to fit. If it's smaller than the current frame buffer format, KONA LHe will center it in the frame. If it's larger than the current frame buffer format, it will be cropped on the right and bottom. Also some graphics formats and bit depths may not be supported. Once a graphic file is loaded into the frame buffer it will be retained until it is overwritten by another graphic or test pattern, or when power is turned off. Graphic file names are only “remembered” in the menu as long as the AJA Control
Panel application is running.
AJA Control Panel, Test Pattern Choices
Hold Last Application: this selection directs LHe to hold and output the last frame of video from the last application to control LHe. This can be helpful when operating in an environment where you're switching back and forth between multiple application windows.
Tip:
pressing and holding the Apple COMMAND key while clicking in the AJA Control
Panel—while in any software application (Final Cut, etc.)—causes control of the KONA to stay with that application, rather than shifting to the Control Panel. This works regardless of the setting of “Default Output.”
Genlock (Freerun, Ref In, Video In)—selects how KONA LHe will synchronize program video:
Freerun: In this mode, KONA LHe generates sync without an external reference source
Ref In: Directs KONA LHe to use the Ref Video source for sync (usually an analog black burst video signal)
Video In: Directs KONA LHe to use whichever video input source has been selected in the
Inputs tab window for sync.
Timing (Horiz and Vert)—these two pull-downs allow output timing adjustment with reference to the Ref Video source selected. The Horizontal reference can be adjusted by selecting a number of pixels (clocks) to offset. Vertical can be adjusted by specifying a number of lines to offset.
KONA LHe Installation and Operation Manual — Using The KONA LHe
Formats Tab Screen
The Formats screen shows the video format currently in use by the KONA LHe framebuffer
(called the Primary Format) and allows you to change it. All throughout the Control Panel, choices are always presented based on what KONA LHe can do with the signals available and the inputs/outputs selected. For example, on the Formats screen, if the output or inputs are a different format than the primary, then you’ll see an additional information pane that allows you to view and edit the secondary format—including control over whether down conversion is employed.
35
1
KONA LHe Control Panel, Formats Tab
KONA LHe Control Panel, Formats Tab, Showing Primary Formats Pulldown Menu
36
Format Screen Settings
Primary (Framebuffer) Format—this pull-down menu shows the currently selected format.
This pull-down appears in both the Primary Format area of the Formats screen as well as the Secondary Format area (if present). If you select an alternate value in the Primary
Format using the pull-down, it will change the format used by the KONA LHe framebuffer.
When a change is made via the Video Format pull-down or by clicking an icon (widget) and selecting a new format via a contextual menu, the block diagram will change to reflect the new format.
VANC—enables or disables VANC data capture and playback.
Secondary (Converted) Format—the formats available can vary based on what the Primary
Format is and the input signal (frame rates of input sources limits the to/from conversion choices). The “Secondary Video Format” pull-down menu lists all compatible formats in black (incompatible formats are shown in gray and cannot be selected). This allows you to see what you've chosen, and also see those formats that are compatible with the selected Primary format.
Note: The AJA Control Panel software uses the abbreviation “sf” instead of “Psf” when referring to “progressive segmented frame” formats. In the manual and in other literature you may see either of these acronyms used interchangeably. Visually it is easier to discern at a glance if you are working with progressively segmented frame formats (sf in the AJA
Control Panel) as compared to progressive frame formats which will show only “p.”
Down (Conversion)—for downconversion the following choices are available:
Anamorphic: full-screen “stretched” image
Letterbox: image is reduced with black top and bottom added to image area with the aspect ratio preserved
Crop: image is cropped to fit new screen size
Input Select Tab
Screen
KONA LHe Installation and Operation Manual — Using The KONA LHe
37
1
Select an Input
KONA LHe Control Panel, Input Select Tab
On the Inputs screen you can view the currently selected video and audio input sources and map audio sources to the channels supported by Final Cut Pro (more on this later). Two information panes in the screen are provided: Video Input and Audio Input.
Input Screen Settings
Video Input—These pulldown menus allow you to see and change what’s currently selected for the video (SDI or Analog) and the audio input. If Analog is selected, then you also need to select the type of Analog input via a pulldown menu. Choices are:
Composite
Y/C
Component (SMPTE/EBU N10)
Component (Beta)
Audio Input—This pulldown menu allows you to pick where the audio comes from. KONA LHe supports up to 8 channels of embedded digital audio, so you can choose out of the 16 channels that can be embedded in SDI, and pick which to bring in (from the group 1-8 or 9-
16). Since Final Cut Pro currently only supports two channels of audio, here you can also select which two channels from the 8 embedded will be mapped to Final Cut’s two channels using the Map Channels pulldown menu.
38
Proc Amp Screen
The Proc Amp screen settings affect the analog proc amplifier built into the KONA LHe. Each of the four sliders controls a video parameter, with the middle being close to unity. If the value has been changed from the factory Unity setting, that value will by displayed in red at the right side of the slider. Clicking the Reset Unity button sets all four sliders back to unity.
Sliders:
Brightness
Contrast
Hue
Saturation
KONA LHe Control Panel, Proc Amp Tab
SDI Output Screen
KONA LHe Installation and Operation Manual — Using The KONA LHe
The Digital Out screen shows the current settings for the two SDI outputs. If an input/output has no video, it will be indicated on the block diagram (“No Video”).
39
1
KONA LHe Control Panel, Digital Out Tab
SDI Output Screen Settings
Information that can appear includes the following items. You can view the current setting or click on another to change to it:
Primary—when selected, this indicates that an SDI output (SDI Output 1 or SDI Output 2) is set to the same format as the framebuffer. That value will be listed in blue.
Secondary—when selected, this indicates that the SDI output is set to a format different from the framebuffer (Primary Format). That secondary format value will be listed in green. This shows that active processing of the video is taking place (format change and possibly down-conversion).
Video+Key—when selected, this selects that both SDI outputs will be used for a Video plus an associated video Key (hole cut). This will be reflected in the block diagram by showing the two lines grouped together going from the framebuffer to the SDI 1 and SDI 2 outputs.
Selecting Video+Key on one pulldown also causes the other pulldown to change to
Video+Key since the outputs are used as a pair.
40
Analog Out Screen
KONA LHe provides a high-quality analog component or composite output, generally used for monitoring. This screen shows the current settings for that analog output, and allows you to re-configure it when desired.
KONA LHe Control Panel, Analog Out Tab
Analog Out Screen Settings
Select—Primary or Secondary (conversion)
Analog Format—choices in the Analog Format pulldown menu vary depending upon the
Analog Output video standard. For example, the “Composite + Y/C” selection is only available when an SD (525i29.97 or 625i25) format is in use. Analog formats can include:
Composite +Y/C
Component (SMPTE/EBU N10)
Component (Beta)
Component (RGB)
Component (RGB -HV)
Monitor Audio—select which two channels will be routed to the stereo pair of unbalanced consumer audio outputs on the KL-Box (option).
KONA LHe Installation and Operation Manual — Using The KONA LHe
Video Setup Screen
The KONA LHe’s Analog Black level and QuickTime Video Output Display Filter are configured here.
41
1
KONA LHe Control Panel, Video Setup Tab
Setup Screen Settings
Analog Black Level—choices in the black Level pulldown menu are only available for the two
Composite analog formats. Choices presented are for US or Japan settings:
7.5 IRE (NTSC US)
0 IRE (NTSC Japan)
QuickTime Video Output Display Filter—these controls help manage the comprehensive list of video outputs and geometries that may be available to applications, particularly Final
Cut Pro's A/V Devices tab.
By selecting the checkbox next to specified parameters, the video outputs related to these specified parameters are enabled as possible video outputs for applications. As an example, if the checkbox next to 25/50 is unchecked, 50Hz video outputs are deselected and would not be available to the user in the A/V Devices tab of Final Cut Pro. To avoid confusion when working in a particular editorial environment, users might elect to leave
50Hz unchecked if they work solely in a 60Hz editorial environment.
Note: If a prompt occurs in Final Cut Pro stating that the AJA output device is missing, this simply may be due to the QuickTime Video Output Display Filter for a given parameter being unchecked for the format selected in the application. If this occurs, simply make the appropriate selection in the Control Panel application and re-enter Final Cut Pro where the selection should now be available.
42
Audio Setup Screen
The KONA LHe’s audio settings are configured here.
KONA LHe Control Panel, Audio Setup Tab
Audio Setup Screen Settings
Lock Audio Gain To Unity—When set, the KONA card will ignore the Final Cut Pro gain setting and set the audio gain at unity. When not set, this checkbox tells the KONA card to get the audio gain setting from Final Cut Pro.
Analog Audio Monitor Level—when a KL-Box is connected to KONA LHe, the button selected determines the audio level that will appear at the Analog Audio Output RCA connector pair (“FSD” is full-scale-deflection reading as measured on a VU meter). Select
+18 for Europe or +24 for USA.
Conversion Tab
Screen
KONA LHe Installation and Operation Manual — Using The KONA LHe
This Tabbed screen is used to set conversion options.
43
1
KONA LHe Control Panel, ConversionTab
Conversion Tab Screen Settings
Pause On—these two choices determine what happens when Final Cut Pro is paused in stop mode:
Full Frame: both fields are displayed resulting in some jitter while paused.
Single Field: a single field is displayed, showing no flicker (useful when color correcting or whenever the flickering would be a distraction).
3-2 Pulldown Pattern—after format selection, the value selected in this pulldown is used whenever you’ve chosen to do 24 frames-per-second to 30 conversion where extra fields are added to pad existing ones. Depending on video content, selection of different field patterns may be useful in reducing jitter due to the content of adjacent fields. The numbers in the pattern choices specify the frequency with which inserted fields will be repeated. For example, “2:3:2:3” means duplicate a field twice, then the next field three times, then the next twice, and then back to three times.
3-2 Pulldown Offset—select a frame offset value from 0 to 4.
RGB-YUV Conversion: These pulldowns select industry standard color space and gamma transfer functions for the YUV-RGB conversion, or allow you to direct the KONA card to automatically determine it for you.
Colorspace—choose from:
Rec 601
Rec 709
Auto
44
Gamma—choose from the following:
Linear (1.8)
Rec 601 (2.20)
Rec 709 (2.22)
Auto
Enable Custom LUTs—this checkbox enables a custom color lookup table (LUT) for use in Final Cut Pro. When checked, there will be a new “Custom LUT” menu item under the
Windows menu in Final Cut. Selecting that item brings up the KONA LHe Control Panel
“Custom LUTs” dialog shown below. Defining a LUT applies it to the KONA LHe output.
The custom LUT will be saved with the Final Cut Pro presets.
Note: Custom LUTs only work with RGB material.
Select a “canned” LUT or create your own
Click to restore factory defaults
Adjust Gain & Offset sliders to change color. Changed values will appear in red in text fields.
You can also enter specific numbers to explicitly set a value.
KONA Custom LUTs Dialog
DS Keyer Screen
KONA LHe Installation and Operation Manual — Using The KONA LHe
The KONA LHe has a hardware-based downstream keyer that is ideal for putting logos, “bugs” or other video material with an alpha channel on top of video being played out or printed to tape.
A typical application would be putting a television station's call letters or channel over program video content. Keyed video can be from the KONA's internal Frame Buffer (from storage, video
In, KONA TV, etc.) or from a graphics file that has an alpha channel (PhotoShop etc.).
45
1
KONA LHe Control Panel, DS Keyer Tab
DS Keyer Screen Settings
Downstream Keyer Mode:
Downstream Keyer Off — when this pulldown menu item is selected the downstream keyer will be turned off
Frame Buffer over Matte— places the keyed video with alpha channel currently in the
Frame Buffer over a fixed color matte determined by the “Matte Color” setting set separately.
Frame Buffer over Video In—places the keyed video currently in the Frame Buffer over the video input for playout or print-to-tape.
Matte Color: only available when the pulldown “Frame Buffer over Matte” or “Graphic over Matte” are selected-pressing this button brings up a color selection dialog. The dialog provides a variety of ways to select a matte color including a color wheel, color picker (choose from a location anywhere on the computer screen), numeric sliders, swatches, “crayons”, and spectrums. The matte chosen will be used as a video background under the keyed video.
Foreground pre-multiplied (checkbox): use to avoid “matte lines” and improve the appearance of the foreground (key) being composited over the background.
Audio Out:
Frame Buffer—select audio out to be routed from the contents of the Frame Buffer.
Audio In—select audio out to be routed from KONA’s currently selected input(s).
46
Timecode Screen
The timecode is used for both monitoring the RP-188 timecode embedded in the digital data stream and for selecting a timecode offset (if required) for the attached VTR (connected to
KONA LHe’s RS-422 port)—and sent during assemble-edit mode.
Note: SMPTE 12M-2 is the updated name and specification for what was RP-188.
KONA LHe Control Panel, Timecode Tab
Timecode Screen Settings
RP-188 Timecode <n>—in RP-188 timecode (SMPTE 12M-2) there can be multiple timecode values in the data stream. Use this pull-down to select the one you wish to monitor. The selection will be displayed in the timecode value displayed to the right of the pull-down.
User Bits—For monitoring variable framerate (VFR) timecode (such as Varicam), you may wish to monitor the user bits embedded in the timecode. If you set this checkbox, KONA
LHe will detect and interpret the user bits and display them next to the checkbox.
KONA LHe Control Panel, Timecode Tab, User Bits Checked
Use QuickTime Timecode—when checked, this directs KONA to output timecode from the
QuickTime timecode track. When not checked, KONA uses the Output Timecode Offset value plus the number of frames into the movie. Note: not all QuickTime applications use or support timecode tracks—so sometimes the QuickTime timecode is missing or not meaningful.
Timelapse Tab
Screen
KONA LHe Installation and Operation Manual — Using The KONA LHe
Output Timecode Offset (entry field and FPS pull-down)—this text entry field allows you to specify a timecode offset for use with Final Cut Pro (or any other application that has timecode offsets that are user-controlled). In FCP, go to “Timeline Options” and locate the
“Starting Timecode” value. Use that same value here as the “Output Timecode Offset” to ensure the timecode is synchronized.
47
Timecode Burn-in—this pulldown selects whether the timecode value is
“burned-in” on video output from KONA LHe. If set to “OFF”, timecode will not be keyed over the video. If set to “timecode”, then the timecode value will be keyed over the output video. This can be useful for synchronizing, choosing edit points, dailies, and many other purposes.
Note: SMPTE RP 188 defines a standard for the transmission of time code and control code in
1 transmitted in the ancillary data space as defined in ANSI/SMPTE 291M. Multiple codes can be transmitted within a single digital video data stream. Other time information, such as real time clock, DTTR tape timer information, and other user-defined information, may also be carried in the ancillary time code packet instead of time code. The actual information transmitted through the interface is identified by the coding of a distributed binary bit.
Equipment manufacturers can use the meta data for different purposes.
This Tabbed screen is used for the KONA LHe timelapse feature. To use the timelapse capability, choose the "Enable Timelapse Capture" checkbox. This functionality is enabled for all QuickTime capture applications (Final Cut Pro, VTR Xchange, etc.) Set the "Capture" and "For Interval" parameters as desired. Launch a capture application like Final Cut Pro, select the desired Easy
Setup for the video format desired. You will not need to change anything within the application; the timelapse feature will produce QuickTime files with the framerate specified by the Easy
Setup used. The resulting timelapse clip can be used without additional rendering.
KONA LHe Control Panel, Timelapse Tab
48
Info Screen
This Tabbed screen shows the KONA LHe software files that have been installed on your system.
This information may be needed if you talk to an AJA Customer Service representative to determine if files are missing or need updating.
KONA LHe Control Panel, Info Tab
Saving Your Control
Panel Presets
KONA LHe Installation and Operation Manual — Using The KONA LHe
After configuring the KONA LHe Control Panel via the Tabbed screens, you can then save all your settings as a snapshot for later recall—called a preset. In this way, you can organize the presets for all your typical tasks, saving time by not having to manually reconfigure each time. To save a preset, simply go to “File -> Save Preset...”. Be sure to give the preset a meaningful name.
Thereafter the preset will be available under the Control Panel “Presets” menu.
49
Who is Controlling
KONA LHe?
If you are consistent in the workflows and formats you use between applications, you generally won’t be surprised by how your system operates. KONA LHe is very flexible and most applications perform the necessary housekeeping so they work correctly when they’re active and when they’re not. However, since several applications using KONA LHe can be running at once, with one active, it can create confusion when settings are different in each and you switch back and forth. To prevent confusion, we recommend you run the KONA LHe Control
Application and have it visible somewhere on your Macintosh desktop. It will tell you, even
1 selections are.
For further understanding, read on and we’ll give you some further background on KONA LHe control. The main issue you’ll generally want to know, is what application has control of KONA
LHe’s Primary Format at the current moment.
Who Has
Priority?
1st Priority
1st Priority
2nd Priority
3rd Priority
Masters
That Can
Control KONA LHe
Final Cut Pro
.
.
Other “QuickTime Application”
Mac OSX Desktop Video
KONA LHe Control Panel Application
Control of KONA LHe and
Primary Format
Selection
When you click in an application window, the “Master” controlling KONA LHe changes, possibly changing the Format Selections in effect.
This happens because each application has it’s own sets of control parameters
TIP: If you keep the KONA LHe Control Panel window in view, it displays the application that is in control and what the Primary and Secondary Format Selections are at all times.
KONA LHe Control Priorities
The KONA Control Panel is one of three masters contending for control—and it’s the lowest priority of the three. The other two masters are: any currently running QuickTime application
(e.g. Final Cut Pro, Apple Motion, After Effects, etc.) using the board and the Mac “Desktop” display. The priority of these three “masters” is:
1. QuickTime Application
2. Macintosh Desktop
3. KONA LHe Control Panel
By “Master”, we mean a process that can control and change what the KONA LHe is doing and the
Primary and Secondary formats that it uses (as set in the Control Panel “Formats” tab screen).
50
QuickTime Application—1st Priority
If a running QuickTime application uses KONA LHe for capture or output, it controls the
Primary format via its own menus and settings. For example, when Final Cut Pro is active (it’s the topmost application) and has KONA LHe as its “A/V Device”, then the KONA LHe'S Primary format is determined by Final Cut's “Video Playback” submenu (under the “View” menu) or its
“Audio/Video Settings...” dialog under A/V Devices.
When a QuickTime application is in control of the KONA LHe board—versus one of the other masters—it will be indicated by a label in both the KONA Control Panel's Formats and Control tabs. The KONA LHe Control Panel’s Primary Format menu will also indicate that it is not active while the QuickTime application is running—it will be grayed-out.
What can be confusing is that QuickTime applications can start and stop and change modes—even while they are running! And the behavior of different QuickTime applications can vary: some applications take control of the board as soon as they are launched and don't give it up until they quit, while other applications take control of the board only when they are the “front-most” running application and then relinquish control when they’re not. Final
Cut Pro is one of the latter type QuickTime applications. This difference in behavior can surprise you when you click in and out of multiple QuickTime application windows.
To illustrate such possible confusion, consider this multiple application scenario:
1. Open Final Cut Pro, select KONA LHe as the A/V device. FCP takes control of the board and tells it what Primary format to use. If one of the FCP windows covers up the KONA
Control Panel application (which typically happens), you won't be able to see the “Kona
card is in use by Final Cut Pro” message displayed in the Control Panel, or be able to tell which format FCP has selected. (This is why we recommend you arrange your display so you can see the Control Panel at all times.)
2. Next, you want to see what the KONA card is doing, so you find the KONA Control Panel application by clicking around on the desktop, eventually clicking on the Control Panel to make it visible. As soon as FCP realizes it is now running in the background, it gives up control of the KONA LHe board. The KONA Control Panel application takes away the
“...Final Cut Pro” message.
3. With the Control Panel the topmost application—and in control of the board—you now switch to a different Primary format.
4. However, when you click back on Final Cut Pro and bring it back to continue your project, it becomes the master again and resets the board's Primary format to the one determined by Final Cut’s A/V Settings dialog. To further the surprise, if FCP's windows are covering the KONA Control Panel window, the change will be hidden and you won’t know why the board isn't doing what you told it earlier via the Control Panel.
The moral of the story: keep the Control Panel visible so you can learn what various QuickTime applications are doing when they control KONA LHe—and then you can step in and change the application’s settings and Control Panel settings as desired to get the configuration you expect.
Mac Desktop Video—2nd Priority
If you choose “Macintosh Desktop” as your KONA Default Video Output (Control Tab), then the
Mac Finder uses the KONA LHe board as a second (or third, or fourth...) graphics “desktop” output—as long as there isn't a QuickTime application running. When the Finder is in control, the Primary Format is dictated by the System Preferences “Displays” panel or by you selecting
“Show Displays in the menu bar”, from the Displays menu near the right side of the main menu bar).
KONA LHe Installation and Operation Manual — Using The KONA LHe
51
1
When the Finder is in control of the KONA board, the KONA Control Panel disables the Primary
Format popup and puts a message in the KONA Control Panel “Formats” tab as follows:
KONA Control Panel—3rd Priority
If a QuickTime application is not running and the Default Video Output is not set to Mac Desktop, then the KONA LHe Control Panel gets control of the board.
Control Recommendations
To avoid surprises, run the KONA LHe Control Panel, keep it visible on the desktop—and stay consistent in your settings within all QuickTime applications when working on a project. For example, if you’re working in a particular format (e.g. 525i29.97), it would make sense to set Final
Cut Pro for 525i29.97, the Mac Desktop size to 720x486, and the KONA Control Panel for
525i29.97. Then, when you switch between applications, the output will stay in the same format.
Having the Control Panel running and visible helps because you can always check and see what the board is doing and who has control of it—even when the Control Panel is running in the background.
52
Using Multiple AJA Products
Starting with the v7.5 drivers, more than one AJA product can be used with your host computer. Using the AJA Control Panel application, you can choose which installed product an application uses for input/output. In the upper left corner of the AJA Control Panel application, you will see a board name, such as Kona3-0, if you have more than one product and the associated drivers installed (if only one product is installed, you’ll see no product or pulldown). To "target" a specific installed product for use, click on the text in the upper left hand side of the UI and select from the list of available products that appear in the pulldown.
When you launch an application such as Final Cut Pro, or AJA TV, that application will use the product that is currently selected in the AJA Control Panel application for its input/output.
Once an application is running, you can change the "targeted" product selection in the AJA
Control Panel and select a different product. The running application will retain its connection to the product. If you change the "targeted" product and launch a different application, that application will use the new product for its input/ output, while the first application you launched will continue to use the other AJA product.
Example: select a KONA 3G as the targeted product in the AJA Control Panel application.
Launch Final Cut Pro. Final Cut Pro is now using the KONA 3 for its input/output. Go back to the AJA Control Panel application and select a KONA LHe as the "targeted" product.
Launch the AJA TV application. AJA TV would now use the LHe for its output. If you switch back to Final Cut Pro, you would note that it is still uses the KONA 3G for its input/ output. Note that some applications, like AJA TV, have a provision for playing in the background, so playback on one product could even continue when switching the targeted device for use with another application. You can even feed the output from one
AJA product to another AJA product on the same system in such cases.
Notes on using multiple AJA
Products:
AJA TV Preferences, Continue Playback when AJA TV is in background
AJA TV optionally supports playback in the background; checkbox “Continue Playback when
AJA TV is in background.
Performance of multi-product use depends on a variety of factors: CPU usage, RAM, disk IOPS/ bandwidth for streams of video, etc. and therefore performance may vary. Also be aware that multiple input/output streams are only supported by software that is explicitly designed for a multi-product environment.
KONA LHe Installation and Operation Manual — Easy Setups for Typical
Easy Setups for Typical Uses
Final Cut and KONA LHe together make working with multiple formats an easy proposition.
Inside of Final Cut, equipment and setting presets are available in groups called Easy Setups, from which you can choose typical system configurations. A large set of Easy Setups are supplied with KONA LHe and installed along with the KONA LHe software. At installation you can choose exactly which sets of Easy Setups you want. These canned choices can be used directly or as the basis for making your own customized Easy Setups unique to your system. By duplicating an Easy Setup and then making changes to it, you simplify the process of configuring and re-configuring when working with new formats.
Although this manual assumes you’re familiar with Final Cut Pro and have read its documentation, let’s review Easy Setups and how to use them effectively with KONA LHe.
1 control, and for project sequences. These presets are defined in the Audio/Video Settings menu.
Just like Easy Setups, here also there are factory defined choices, plus you can create and make your own. When you have a set of presets you want to use again, you can store them as an “Easy
Setup.”
On the following pages we’ll further review the Easy Setups menu and Audio/Video Settings
Menu.
53
Easy Setups Menu
Both the Easy Setups menu item and the Audio/Video Settings menu item are located under the main Final Cut Pro menu.
Easy Setup and Audio/Video Menu Items
Click on the Easy Setups menu item and Final Cut Pro will present the Easy Setup dialog window:
54
Easy Setup dialog
At the top of the Easy Setup dialog is the currently selected Easy Setup. It can be changed by clicking on the pulldown arrow at the right. Doing so results in a long list of the factory Easy
Setups stored on the system. If you wish to see all of the Easy Setups, factory and userdefined, then ensure the “Show All” checkbox is marked at the right side of the dialog. By default, all AJA Easy Setups will be checked.
A large set of Easy
Setups are
Provided as KONA
LH defaults
Factory Easy Setups
To choose a new Easy Setup from the list, click on the pulldown menu and select a desired choice. The choice won’t take effect until you click the Setup button, but you will be able to see
Audio/Video
Settings Menu
KONA LHe Installation and Operation Manual — Easy Setups for Typical
the description for the choice just by selecting it (without clicking the Setup button).
Descriptions provide a paragraph summarizing what the Easy Setup is intended for and then each of the presets are explained (Sequence, Capture, Device, Playback Output, and Edit to Tape
Video/Audio Outputs).
55
Easy Setups For Use With KONA LHe
The factory default Easy Setups currently shipped with KONA LHe are updated regularly by AJA and posted on the relevant support web page for your model of KONA. In addition to this, there are additional easy setups available on your KONA Software CD
The Audio/Video Settings menu in Final Cut Pro contains a series of tabbed windows where you
1
When you open the Audio/Video Settings window, it shows a summary of the currently selected
Easy Setup. Other tabbed windows are available with greater details about each category. On the initial summary window you can see the selected presets for the Easy Setup as well as change specific presets.
The presets you can change on the Summary window are:
Sequence Preset—select one of these as the editing timebase for new sequences. If you make a change to Sequence Presets, the change will only take effect on any new sequences you create—currently active sequences will not see the change.
Capture Preset—select one of these to set the incoming source format you’ll be capturing.
Ideally select the maximum quality format you’ll be using for most of the material so there will be no need to re-render later as clips are added from the bin to the sequence.
Device Control Preset—select the AJA Video KONA LHe device (NTSC or PAL as desired). This tells Final Cut that the KONA LHe will control the VTR attached to KONA LHe or KL-Box.
A/V Devices (Audio and Video Playback)—select the KONA LHe as video and audio playback devices for Final Cut and the format to be output.
Audio/Video Settings, Summary Window
56
To Create A New Easy Setup
If you have a group of presets that you’d like to use continually, then you can create a new
Easy Setup by modifying the settings of the Easy Setup currently selected (pick one most like the one you want to create) and then saving it under a new name:
1. Change the currently selected Easy Setup by making changes at the Summary tabbed window via the pulldown menus.
2. When everything is set as desired, click on the Create Easy Setup button at the bottom of the Summary window.
3. A new dialog will pop up. Enter a descriptive name for the new Easy Setup (i.e., 10-bit
SDI from Video Server) in the Name field.
4. Enter a sentence or two describing what is unique about the Easy Setup in the
Description field.
5. Click the Create button to store the new Easy Setup.
Click Here
Audio/Video Settings, Creating a New Easy Setup
At any point in the above procedure you can go to the other tabbed windows and make additional changes. For example, in the Sequence Presets, Capture Presets, and Device
Control Presets windows you can select a preset and click on an Edit button to change specific aspects of the preset. As an example, under Device Control Preset you might wish to change the Time Source on your VTR from LTC to VITC, or change the pre-roll and post-roll values.
When you save a Setup, it defaults to saving in the Final Cut Pro Custom Setups folder.
Each of the tabbed preset screens are described on the following pages for your convenience.
For more information, please read the Final Cut Pro user documentation.
KONA LHe Installation and Operation Manual — Easy Setups for Typical
57
The Sequence Presets Window
1
Audio/Video Settings, Sequence Presets Window
This window allows you to select an editing timebase for the current sequence. Once you add a clip to the sequence this cannot be changed.
For example, once you’ve selected uncompressed 10-bit NTSC 48 kHz, you then have to stay in that timebase and can’t switch to another. By clicking in the leftmost column (see the checkmark in the sample screen above), you select a new Sequence Preset for use. The checkmark tells which Preset is in use—highlighting a choice alone does not select it.
If you select an editing timebase you can then edit it (click the Edit button) or copy and rename it as another (click Duplicate). When editing a timebase you can change the following:
• Select video processing properties (how to render)
• Frame size and aspect ratio
• Pixel aspect ratio
• Field dominance (none, upper, or lower)
• Editing timebase
• Set QuickTime video codec settings (quality and type)
• Select audio sample rate
58
Audio/Video Settings, Sequence Presets Editor Window
The Capture Presets Window
Audio/Video Settings, Capture Presets Window
KONA LHe Installation and Operation Manual — Easy Setups for Typical
This window lets you choose a preset format for incoming source video and audio media you’ll be capturing.
Select the maximum quality format you’ll be using for most of the material so there will be no need to re-render later. The information on the right window pane describes the preset and all it’s parameters. If you select a format by making a checkmark in the left column, you can edit it
(click the Edit button) or copy and rename it as another (click Duplicate). The only exceptions to this are those presets marked with a lock icon; those can be duplicated, but when you try to edit one the system reports they’re locked and can only be copied (it will create the copy for you when you try to edit).
Factory AJA presets are easily identified by “AJA” at the beginning of their name.
Since Capture Presets will be used frequently as you bring media into KONA LHe, we’ll discuss the edit screen next.
1
Capture Presets Editing
59
Audio/Video Settings, Capture Presets Editing Window
Note: Whenever a Preset is being copied as the basis of a new preset, always change the name and description to fit the new preset so users aren’t confused between it and the original.
Frame Size—below the name and description are the frame size settings. These can be changed via the pulldown menu. Selecting a new Aspect Ratio value also changes the values in the width and height fields.
QuickTime Video Settings—these settings select a video input source and affect how it’s processed by Final Cut Pro. The Digitizer pull-down menu selects whether you want the selected input source to be digitized as 8-bit or 10-bit uncompressed video as it comes into
KONA LHe. The Input pull-down selects the primary format KONA LHe will use to capture input video. The Compressor pull-down selects a codec that tells Final Cut how to process the video; the codec selected should be chosen for compatibility with the Digitizer setting selected. For example, if your Digitizer setting is 10-bit Uncompressed, then the
Compressor setting should be one of the 10-bit choices available. The Quality slider should be set to 100 percent when capturing uncompressed; for other formats use an appropriate quality level.
60
Set the FPS (Frames Per Second) setting to the correct frame rate. The Advanced settings button opens a new screen providing choices of codec-specific options. For uncompressed codecs these probably are not unneeded; for other codecs choose the options desired.
QuickTime Audio Settings—these settings select an audio input source and affect how it’s processed by Final Cut Pro. The Device pull-down should be set to AJA Kona. The Input pull-down selects that KONA LHe (AJA Kona) will be used for capturing audio—it does not select the specific inputs. For specific audio input selection use the KONA LHe Control
Panel. The Rate pull-down selects a sample rate; it should always be set to 48 kHz for
KONA LHe. By clicking on the Advanced button, a new screen will be displayed where you can select between 8- and 16-bit sampling—AJA recommends 16-bit for optimum sound quality. (This has nothing to do with input format, as KONA LHe supports 20-bit SD embedded audio, and 24-bit AES audio.)
The Device Control Presets Window
Audio/Video Settings, Device Control Presets Window
This window selects machine control parameters for an attached VTR. Your choice here tells
Final Cut that KONA LHe is handling the machine control parameters for the VTR attached to
KONA LHe. Alternatively, you could also select a different device for input/output instead of
KONA LHe.
For example, if you have a IEEE 1394 camcorder attached to the Mac’s FireWire port you might choose “FireWire NTSC.” The information on the right window pane describes the current machine control settings and parameters for the VTR attached. For KONA LHe presets this means the VTR attached at the RS422 port on KONA LHe. For non-KONA LHe presets, this means camcorder/VTRs attached directly at the FireWire port or via some other interface.
If you select a preset you can edit it (click the Edit button) or copy and rename it as another
(click Duplicate). The only exceptions are those presets marked with a lock icon; those can be duplicated, but when you try to edit one the system will report they’re locked and can only be copied (it will create the copy when you try to edit).
KONA LHe Installation and Operation Manual — Easy Setups for Typical
61
When editing a Device Control preset you can change the following:
• Name and description of Device Control preset
• Protocol for capture/playback VTR (for KONA LHe this will be RS422)
• Audio Mapping
• Time Source (LTC/VITC/both/etc.)
• Port
• Frame Rate
• Default Timecode (Drop Frame etc.)
• 1
• Handles/Pre-roll/Post-roll
• Auto Record and PTV
KONA LHe ships with VTR Device Control Presets for Sony and Panasonic VTRs. Select a Device
Control Preset for the desired frame rate. Presets for both Sony and Panasonic VTRs are provided with these frame rates: 23.98, 24, 25, 29.97, and 59.94.
Audio/Video Settings, Device Control Presets Editor Window
62
The A/V Devices Window
Audio/Video Settings, A/V Devices Window
The A/V Devices window selects the current playback device for both audio and video.
Typically, you’ll select KONA LHe for both playback devices. The format chosen determines the
Primary format for the KONA LHe board during playback. The Video Options button is greyed out for KONA LHe (use the KONA LHe Control Panel for video configuration; the Audio Options button opens a second dialog where Final Cut gives options for changing bit depth, number of channels, and the sample rate. Since Final Cut currently only supports 2 channels of audio,
AJA recommends you leave all of these settings as set in the factory defaults.
You may wish to use a different KONA LHe output for final Print-to-tape from Final Cut. You can select that in this window by clicking the checkbox “Different Output for Edit to Tape/Print to Video.” This allows you to select via a pull-down menu any KONA LHe video output and audio output.
The window also allows you to turn on and off device and audio output warnings.
KONA LHe Installation and Operation Manual — Checking the System with a
Checking the System with a Simple Test Project of Bars and Tone
To test that you’ve installed the KONA LHe drivers and have audio and video monitoring correctly configured, try creating a simple Final Cut Pro project with bars and tone.
1. Select an Easy Setup as previously discussed (go to the Final Cut Pro menu and select
Easy Setup; then select a desired preset).
2. Select New Project from the File menu.
63
1
Create a New Project
3. The Sequence window will be at the bottom of the screen and a Browser window will be at the top left. Look at the Browser window and locate the “Effects” tab at the top right.
Click on it.
4. Locate the Viewer window in Final Cut and click on the Filmstrip pulldown menu button
(it’s a “filmstrip” icon with an “A” on it). Select “Bars and Tone NTSC” or “Bars and Tone PAL”.
The viewer window will display bars after you do this.
5. Click the mouse cursor on the Bars and Tone in the Viewer window and drag it to the beginning of the sequence window. You’ll see the bars and tone show up on the sequence where it can be played.
6. Go to the beginning of the sequence by clicking on the left-most icon and then click the
“Play” icon. You should see and hear the bars and tone on your video monitor and audio monitoring system.
If you don’t see bars on the external video monitor and hear tone, check your connections and ensure KONA LHe is selected in the Easy Setups and Audio/Video Settings as necessary.
64
Click Filmstrip Button in Viewer Window
...Then select “Bars and Tone”
Finally, click in the viewer window and
drag the “bars” to the Sequence window.
Click and Drag Bars and Tone From Viewer Window To Sequence
KONA LHe Installation and Operation Manual — Checking the System with a
65
1
Bars and Tone
In Sequence
Window
Click “Play” to
Test the
System
Sequence Window Showing Bars and Tone Clip Dragged from Viewer
If everything works properly, go ahead and try capturing audio and video media from your VTR.
66
Using 8-bit Versus 10-bit Video
While both 8- and 10-bit uncompressed video are capable of providing excellent quality broadcast video, 10-bit represents a significantly higher quality and is preferable in many situations.
Because 10-bit video has four times the numerical precision when compared to 8-bit, it has a signal-to-noise ratio 12 db higher than 8-bit video.
Visually, in 8-bit video compared to 10-bit video, you will notice a substantial difference. In 8bit video there will be “contour lines” or “striations” visible, particularly noticeable in scenes having soft gradients like a ramp or sunset. For example, if a sky region is mostly the same color but varies by only a few digital numbers from one side of the picture to another, you may see contour lines where the signal passes from one digital value to the next higher value.
Since each numerical value in a 10-bit system is only one fourth as large as an 8-bit system's, these contours become invisible and the sky varies smoothly.
10-bit video is often used when the source and output video (or “master”) is also 10-bit. Even if the input and/or output video is 8-bit, a 10-bit “project” will still maintain a higher quality when there is a significant amount of effects rendering involved.
Industry standard professional mastering formats—Sony Digital Betacam for Standard
Definition and Panasonic D5 for High Definition—are both true 10-bit formats.
Chapter 5: Troubleshooting
If You Run Into Problems
One useful way to find the source of problems is to isolate your system to the smallest size where the problem still occurs and then note all the symptoms. This serves to eliminate areas not involved in the problem and makes finding the problem easier.
Once you’ve noted problem symptoms, look through the following table and see if any of the symptoms are listed. If so, check the items listed. If you later need to call for customer service, let them know all of the things you’ve tried and when and how the symptoms appeared.
Symptom Check
Disk RAID cannot keep up (dropped frames etc.).
Dropped frames during playback.
Ensure the disk system is providing at least 50 MB/second sustained transfer rate
1. Canvas/Viewer zoom setting exceeds the fit-towindow setting. Change to “Fit-to-Window.”
2. RAID cannot sustain the data rate of the clip/sequence.
3. The sequence setting does not match the “playback output setting” found at FCP Audio/Video Settings -> AV
Output.
4. Virus checking software running in the background
(disable it).
5. Scratch drive not set to the RAID.
Dropped frames during record.
1. RAID cannot sustain the data rate of the capture preset codec.
2. Virus checking software running in the background
(disable it).
3. Scratch drive not set to the RAID.
Media is not being captured from desired external device.
Check the settings in the Input tab of the KONA LHe
Control Panel application. Also check equipment cables.
Dropped frames during playback Look for scroll bars in the viewer or canvas as a warning sign that the zoom setting exceeds the fit-t-window.
5
1 1
68
Symptom Check
Changes made to Final Cut’s configuration aren’t remembered or you need to force a change to them.
Under some circumstances, Final Cut Pro may need to be initialized back to the factory default state as it was when you installed it. The easiest way to do this is to locate
Final Cut’s preference file and discard it.
To do so, follow this procedure:
1. Locate the file named “Final Cut Pro x.x Preferences”.
Note: path to file is “Macintosh HD/users/username/ library/preferences/final cut user data.”
3. Click and drag that file to the Trash Can icon and drop it there.
When you next start up Final Cut Pro, it will present the
“Choose Setup” prompt (as in initial installation) where you can again choose a desired KONA LHe input format in the “Setup For” pulldown and re-enter a desired system scratch disk (your RAID).
Video in the canvas stays frozen during playback.
Video output is black.
1. The sequence setting does not match the “playback output setting” found at FCP Audio Video Settings -> AV
Output.
2. Canvas/Viewer zoom setting exceeds the fit-towindow setting. Change to “Fit-to-Window.”
1. External video is set to “No Frames” (View -> External
Video).
2. The “Playback output setting” found at FCP Audio
Video Settings -> AV Output is set to “none” or to a non-
KONA LHe device.
Video stutter during playback.
RAID cannot sustain data rate.
Red render bar occurs when placing a clip on a sequence.
The sequence setting does not match the clip setting.
Updating Software
Check on the AJA Video website (www.aja.com/support_kona.html) for software updates. If any are available, download the file and read any associated instructions prior to installing the software.
Support
When calling for support, first check over your system configuration and ensure everything is connected properly and that current Final Cut presets and Easy Setups match what you are trying to do. Even if you cannot find the cause of the problem, having this information at hand will help when you call Apple or AJA Customer Support for help.
If the problem is unknown or you need general help, first contact the dealer where you purchased the product. AJA dealers offer product support for many service requirements.
If the problem is a Final Cut Pro operational issue, Mac Pro system issue, or Xserve RAID issue, then call Apple Customer Support for help.
Apple Resources
KONA LHe Installation and Operation Manual — Support
If the problem is an AJA Video KONA LHe issue, then contact AJA Video Customer Support using one of the methods listed below:
Contacting by Mail Address:
180 Litton Drive, Grass Valley, CA. 95945 USA
Telephone: 1.800.251.4224 or 1.530.274.2048
Fax: 1.530.274.9442
Web: http://www.aja.com
Support Email: [email protected]
69
Apple provides a large amount of support information online at their support website.
Information provided includes answers to top questions, discussions on specific topics, and software downloads for updates and utilities.
products. Information is provided on the Apple Support website on how to enroll in
AppleCare.
General Apple Support Website for information on all products: http://www.info.apple.com/
Mac Pro Support Area: http://www.apple.com/support/macpro/
Final Cut Pro Web Support: http://www.info.apple.com/usen/finalcutpro/
Final Cut Discussion Area:
http://www.apple.com/support/finalcutpro/
70
Appendix A: Specifications
Formats
Video Input
Video Output
525i 29.97
625i 25
720p 59.94
720p 60
1080i 25
1080i 29.97
1080i 50
1080psf 23.98
1080psf 24
Digital: 8 or 10 bit HD-SDI/SDI, SMPTE-259/292/296, Dual-rate
Analog:
Composite/S-Video (Y/C): NTSC, NTSCJ, PAL
12 bit A/D, 2x oversampling
3 line adaptive comb filter decoding
+/- .25 db to 5.0 MHz Y Frequency Response
+/- .25 db to 1 MHz C Frequency Response
.5% 2T pulse response
Component:
< 1.5% Diff Phase
< 1.5% Diff Gain
SMPTE/EBU N10, Betacam 525 line, Betacam 525J, RGB
12 bit A/D, 2x oversampling
+/- .25 db to 5.5 MHz Y Frequency Response
+/- .25 db to 2.5 MHz C Frequency Response
.5% 2T pulse response
<2 ns Y/C delay inequity
Digital: SD-SDI, SMPTE, 259M, 10-bits, BNC
HD-SDI SMPTE, 292/296, 10-bits, BNC
Analog:
Composite/S Video:
SD Component:
NTSC, NTSCJ, PAL
12 bit D/A, 8x oversampling
+/- .2 db to 5 MHz Y Frequency Response
+/- .2 db to 1 MHz C Frequency Response
.5% 2T pulse response
< 1% Diff Phase
< 1% Diff Gain
SMPTE/EBU N10, Betacam 525 line,
Betacam 525J, RGB
12 bit D/A, 8x oversampling
+/- .2 db to 5.5 MHz Y Frequency Response
+/- .2 db to 2.5 MHz C Frequency Response
.5% 2T pulse response
<1 ns Y/C delay inequity
A 1 1
A-2
Analog SD and HD Output, 12-bits, BNC:
HD:
SD:
YPbPr, RGB
YPbPr, RGB (component mode)
Composite/YC (composite mode)
Audio Input
Digital: 2-channel 24 bit AES/EBU, 48KHz sample rate
Synchronous or Non-synchronous
(Internal sample rate conversion)
24 bit SMPTE-259 SDI embedded audio, 8-ch, 48kHz synchronous
Analog: 2-channel balanced input
+24dbu Full Scale Digital
24 bit A/D, 48 KHz sample rate
+/- 0.2db 20 to 20 KHz Frequency Response
Audio Output
Digital: 2-ch 24-bit AES/EBU, 48 KHz sample rate
24 bit SMPTE-259 SDI embedded audio, 8-ch, 48 KHz synchronous
Analog: 2-channel Balanced output (XLR)
+24dbu Full Scale Digital (0dbFS)
24 bit D/A, 48 KHz sample rate
+/- 0.2db 20 to 20 KHz Frequency Response
2-channel unbalanced output (RCA-jack): requires KL-Box option
Down-Conversion
Hardware: 10-bit output, 24-bit internal processing
Anamorphic: full-screen
Letterbox: image is reduced with black top and bottom added to image
area with the aspect ratio preserved
Crop: image is cropped horizontally
Reference Input
Analog Color Black or HD Tri-level
1 BNC on standard breakout cable (75 ohm terminating)
KL-Box (optional): 2 BNCs, passive loop-through
Hardware Acceleration Provided
DVCProHD hardware acceleration
HDV hardware acceleration
Dynamic RT Extreme hardware acceleration
KONA LHe Installation and Operation Manual — Machine Control
A-3
Machine Control
RS-422, Sony 9-pin protocol Connector provided on KONA LHe breakout cable and on optional KL-
Box. 9-pin D-connector pinout is as follows:
1............. GND
2............. RX-
3............. TX+
4............. GND
5............. No Connection
6............. GND
7............. RX+
8............. TX-
9............. GND
Shell....... GND
1
A-4
KONA LH/LHe Installation and Operation Manual — Index
I-1
Index
Symbols
.pkg
Numerics
10-bit video
24 frames-per-second to 30 conversion
48kHz audio
8-bit Versus 10-bit Video
8-channel 24-bit 48kHz AES
9-pin D-connector
A
A/V Devices
AES audio
AES/EBU
AES/EBU Audio Inputs
Analog 4 Channel Balanced/Unbalanced Audio 9
analog component
analog composite
Analog Format
Analog monitor output
Analog Out Screen
Analog Out Screen Settings
Apple Support
aspect ratio
Audio Input
audio input/output
Audio Mapping
Audio Out
Audio/Video Settings
Audio/Video Settings Menu
B
Balanced
Bars and Tone, sample FCP project
Betacam
black burst
Black Level
block diagram element
Block Diagram Screen
BNC Connectors
BNCs for Audio
Box
Box Contents
Browser window
C
Cable Connections
Cable connector descriptions
cables
cables, what’s included
camcorders
capacity
Capture Preset
CD
Chassis Connections
Checking the System
codec settings
codecs
Color Meanings, Control Panel 32
COMMAND key
Component Analog Video Out
Component settings
Component/Composite
composite output
Composite settings
Connector Descriptions
connectors
Control Panel Presets
Conversion Icons
Conversion Icons, Control Panel 32
Crop
customer service
D data protection
DB9
Digital Out Screen Settings 39
Down (Conversion)
drivers
DV (DV25)
DV50
DVCProHD
E
Easy Setups Menu
I-2
embedded audio
F
Factory Easy Setups
Features
features
Fibre Channel
Field dominance
Final Cut Pro 4
Final Cut Pro and KONA
Final Cut Pro™
Final Cut Pro™ support
Foreground pre-multiplied (checkbox) 45
Format Screen Settings
format, primary
Formats and Transfer Rates/Storage Table 6
formats, mixing and matching 15
Frame Buffer over Matte
Frame Rate
Frame Size
Frame size
Framebuffer
G
Genlock
Genlock and Your System
graphic file, test pattern output
H
Hardware
hardware and software requirements 4
Hours of Storage
house reference sync
I
Icons
icons
Info Screen
Input Screen
Input Screen Settings
Input/Output
Installation Overview
Installation Software CD-Rom
Installer Screen
Installing Io Software
Installing the KONA Card 19, 20
Introduction, KONA 2
IRE
K
KL-Box connector descriptions
KL-Box, Front and Rear
keyed video
KONA Software
L
Letterbox
Limitations
Lock Input Audio Gain To Unity 42
Log On Authenticate Prompt
LTC
LUT
M
Machine Control
Machine Control, pinout
Manual
Matte
minimum hardware and software requirements
minimums
Mirroring
Mixing and Matching Formats
Monitor Audio
Monitor Out
O offset, video adjustment (timing)
OS X installer files
Output Pulldown Menu
P
pattern, test
PCI-Express slots
pinout, RS-422 D-connector
Pixel aspect ratio
playback device
Post-roll
Pre-roll
presets
Presets, KONA Control Panel 49
Primary
Primary format
KONA LH/LHe Installation and Operation Manual — Index
I-3
Print-to-tape
problem symptoms
Problems, what to do
problems, what to do if you encounter
progressive frame
36 progressive segmented frame 36
psf
Q
QuickTime Audio Settings
QuickTime video
QuickTime Video Settings
QuickTime™ Drivers, AJA KONA
R
RAID
RAID 0
RAID 1
RAID 5
RAIDs
RCA connector pair, KL-Box configuration 42
rear panel
Recommended System Requirements
Ref Loop
Reference Video
Requirements, System
RGB
RP 188 definition
RP-188
RP-188 Timecode
RS422
RS-422, Sony 9-pin protocol. 9-pin D-connector pinout
S sample rate
Sample rate conversion
Save Preset..
Scenarios, workflow
SCSI RAID
SDI embedded audio
SDI Input and Outputs
Secondary
Sequence Preset
Sequence window
set up
shipping
SMPTE protocol
SMPTE RP 188
snapshot, Control Panel settings 49
Software
Software CD
software files that have been installed
Software License Agreement Screen 25
software requirements
software updates
software, 3rd-party
Standard Cables
Storage capacity
Storage Methods
Striping
Striping data
Support, 3rd-party software
sync generator
synchronizing other video equipment
system configuration, Control Panel 29
system interconnections
T
Tabs available, Control Panel
Time Source
timebase
Timecode
Timecode Offset
Timecode Screen
Timecode Screen Settings
timing adjustment
Transfer Rate
Transfer Rate Table
Troubleshooting
typical system interconnections 22
Typical Workflows
U
Uncompressed 10-bit
uncompressed media
Unpacking
user and password
User Bits, RP-188
V
video and audio input/output connections
I-4
Video Format
Video Input
video input source
Video Monitor
video path
video processing properties
Video/Audio connections
VITC
VTR
VTR RS-422 Control Port
VTRs,
W
Workflow
X
Y
Y/R-Y/B-Y
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 7 Table of Contents
- 7 Overview
- 7 Features
- 8 KONA LHe Audio
- 8 Software
- 8 What’s In The Box?
- 10 System Requirements
- 10 Minimum and Recommended System and Software Requirements
- 11 Understanding Disk Storage Methods
- 11 About RAIDs
- 12 Software For Striping
- 12 Storage capacity
- 13 Cable Connections
- 13 Using the Breakout Cable and 3 BNCs
- 13 Using KL-box
- 14 About BNC Connectors
- 14 Connector Descriptions—Cables and KL-box
- 14 SDI Input and Outputs
- 15 2 Channel Digital AES/EBU Audio Inputs And Outputs
- 15 Analog 2 Channel Balanced Audio
- 15 Analog 2 Channel Unbalanced Audio (KL-box only)
- 15 RS422 Machine Control
- 15 Analog Monitor Out (Component/Composite HD/SD)
- 15 Reference Video
- 16 In This Manual
- 17 Chapter 2: Getting Started—WorkflowKONA LHe And Your Workflow
- 18 Understanding Typical Workflows
- 18 PhotoJPEG
- 18 DV (DV25)
- 18 DVCPRO HD
- 20 Apple ProRes 422 and Apple ProRes 422 HQ (SD or HD)
- 20 Uncompressed 8-bit
- 20 Uncompressed 10-bit
- 21 Mixing and Matching Formats in Final Cut
- 23 Installation Overview
- 23 Unpacking
- 23 Shipping Box Contents
- 25 Installing the KONA LHe Card in a Mac Pro
- 26 Installing the KONA LHe Card in a G
- 27 Cabling the System
- 27 System Video/Audio Cable Connections
- 27 System Cabling When Using The Breakout Cable
- 28 Typical System
- 29 Installing KONA LHe Software
- 29 Software Installation Procedure
- 33 Genlock and Your System
- 35 Final Cut Pro
- 35 Using The KONA LHe Control Panel
- 35 Control Panel Basics
- 39 Control Tab Screen
- 39 Control Tab Screen Settings
- 41 Formats Tab Screen
- 42 Format Screen Settings
- 43 Input Select Tab Screen
- 43 Input Screen Settings
- 44 Proc Amp Screen
- 45 SDI Output Screen
- 45 SDI Output Screen Settings
- 46 Analog Out Screen
- 46 Analog Out Screen Settings
- 47 Video Setup Screen
- 47 Setup Screen Settings
- 48 Audio Setup Screen
- 48 Audio Setup Screen Settings
- 49 Conversion Tab Screen
- 49 Conversion Tab Screen Settings
- 51 DS Keyer Screen
- 51 DS Keyer Screen Settings
- 52 Timecode Screen
- 52 Timecode Screen Settings
- 53 Timelapse Tab Screen
- 54 Info Screen
- 55 Saving Your Control Panel Presets
- 55 Who is Controlling KONA LHe?
- 56 QuickTime Application—1st Priority
- 56 Mac Desktop Video—2nd Priority
- 57 KONA Control Panel—3rd Priority
- 57 Control Recommendations
- 58 Using Multiple AJA Products
- 58 Notes on using multiple AJA Products
- 59 Easy Setups for Typical Uses
- 59 Easy Setups Menu
- 61 Easy Setups For Use With KONA LHe
- 61 Audio/Video Settings Menu
- 62 To Create A New Easy Setup
- 63 The Sequence Presets Window
- 69 Checking the System with a Simple Test Project of Bars and Tone
- 72 Using 8-bit Versus 10-bit Video
- 73 If You Run Into Problems
- 74 Updating Software
- 74 Support
- 75 Apple Resources