Craftsman 315.271190 Owner`s manual

Owner’s Manual
®
6-1/2 in. (165 mm) 18 VOLTS PROFESSIONAL
CORDLESS TRIM SAW
Model No.
315.271190
50
45
CAUTION: Read and follow
0
1
2
1
30
45
4
1
5
3
3
30
2
Save this manual for
future reference
all Safety Rules and Operating
Instructions before first use of
this product.
Customer Help Line: 1-800-932-3188
• Safety
• Features
• Assembly
• Operation
• Maintenance
• Parts List
Sears Roebuck and Co., Hoffman Estates, IL 60179 USA
Visit the Craftsman web page: www.sears.com/craftsman
R
972000-765
9-01
TABLE OF CONTENTS
■
General Safety Rules .............................................................................................................................................. 2-3
■
Specific Safety Rules/Symbols ................................................................................................................................ 3-5
■
Features .................................................................................................................................................................. 5-8
■
Assembly ............................................................................................................................................................... 9-10
■
Operation ..............................................................................................................................................................11-18
■
Maintenance ............................................................................................................................................................. 19
■
Accessories .............................................................................................................................................................. 20
■
Warranty ................................................................................................................................................................... 20
■
Exploded View And Repair Parts List .................................................................................................................. 22-23
■
Parts Ordering / Service ........................................................................................................................................... 24
GENERAL SAFETY RULES
WARNING: Read and follow all instructions.
Personal Safety
Failure to follow all instructions listed below, may result
in electric shock, fire and/or serious personal injury.
■
SAVE THESE INSTRUCTIONS
Work Area
■
■
■
Keep your work area clean and well lit. Cluttered
benches and dark areas invite accident.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases, or dust. Power tools may create
sparks which may ignite the dust or fumes.
Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you to
lose control.
■
■
Electrical Safety
■ Do not abuse the cord. Never use the cord to carry
the charger. Keep cord away from heat, oil, sharp
edges, or moving parts. Replace damaged cords
immediately. Damaged cords may create a fire.
■ A battery operated tool with integral batteries or a
separate battery pack must be charged only with
the specified charger for the battery. A charger that
may be suitable for one type of battery may create a
risk of fire when used with another battery. Use battery
only with charger listed.
MODEL
BATTERY PACK
CHARGER
315.271190
Item No. 9-11034
Item No. 9-11040
(981404-001)
(981399-001)
■
Use battery operated tool only with specified
designated battery pack. Use of any other batteries
may create a risk of fire. Use only with battery pack
listed.
2
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use tool while tired or under the influence of
drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious
personal injury.
Dress properly. Do not wear loose clothing or
jewelry. Contain long hair. Keep your hair, clothing,
and gloves away from moving parts. Loose clothes,
jewelry, or long hair can be caught in moving parts.
Avoid accidental starting. Be sure switch is in the
locked or off position before inserting battery pack.
Carrying tools with your finger on the switch or inserting
the battery pack into a tool with the switch on, invites
accidents.
■
Remove adjusting keys or wrenches before turning
the tool on. A wrench or a key that is left attached to a
rotating part of the tool may result in personal injury.
■
Do not overreach. Keep proper footing and balance
at all times. Proper footing and balance enable better
control of the tool in unexpected situations.
■
Use safety equipment. Always wear eye protection.
Dust mask, nonskid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
GENERAL SAFETY RULES
Tool Use and Care
■
■
■
■
■
■
■
Use clamps or other practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable and
may lead to loss of control.
Do not force tool. Use the correct tool for your
application. The correct tool will do the job better and
safer at the rate for which it is designed.
Do not use tool if switch does not turn it on and off.
A tool that cannot be controlled with the switch is
dangerous and must be repaired.
Disconnect battery pack from tool before making
any adjustments, changing accessories, or storing
the tool. Such preventive safety measures reduce the
risk of starting the tool accidentally.
Store idle tools out of the reach of children and
other untrained persons. Tools are dangerous in the
hands of untrained users.
When battery pack is not in use, keep it away from
other metal objects like: paper clips, coins, keys,
nails, screws, or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
sparks, burns, or a fire.
■
■
Maintain tools with care. Keep cutting tools sharp
and clean. Properly maintained tools with sharp cutting
edges are less likely to bind and are easier to control.
Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that
may affect the tool’s operation. If damaged, have
the tool serviced before using. Many accidents are
caused by poorly maintained tools.
Use only accessories that are recommended by the
manufacturer for your model. Accessories that may
be suitable for one tool, may create a risk of injury
when used on another tool.
Service
■
■
Tool service must be performed by a qualified
repair personnel. Service or maintenance performed
by unqualified personnel could result in a risk of injury.
When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance
section of this manual. Use of unauthorized parts or
failure to follow Maintenance Instructions may create a
risk of shock or injury.
SPECIFIC SAFETY RULES AND/OR SYMBOLS
Additional Rules For Safe Operation
■
■
■
Know your power tool. Read operator’s manual
carefully. Learn its applications and limitations, as
well as the specific potential hazards related to this
tool. Following this rule will reduce the risk of electric
shock, fire, or serious injury.
Make sure your extension cord is in good condition. When using an extension cord, be sure to use
one heavy enough to carry the current your product will draw. A wire gage size (A.W.G.) of at least
16 is recommended for an extension cord 100 feet
or less in length. A cord exceeding 100 feet is not
recommended. If in doubt, use the next heavier
gage. The smaller the gage number, the heavier the
cord. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating.
■
■
■
Important Rules For Battery Tools
■
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
when not using your battery tool or when changing
accessories.
3
Do not place battery tools or their batteries near
fire or heat. They may explode. Following this rule
will reduce the risk of electric shock, fire, or serious
personal injury.
Do not charge battery tool in a damp or wet location. Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
Your battery tool should be charged in a location
where the temperature is more than 50°F but less
than 100°F. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in
contact with your skin, wash immediately with soap
and water, then neutralize with lemon juice or
vinegar. If liquid gets into your eyes, flush them
with clean water for at least 10 minutes, then seek
immediate medical attention. Following this rule will
reduce the risk of serious personal injury.
SPECIFIC SAFETY RULES AND/OR SYMBOLS
Additional Specific Safety Rules
■
■
■
■
■
■
■
■
■
■
■
■
DANGER! Keep hands away from cutting area and
blade. Keep your second hand on auxiliary handle
or motor housing. If both hands are holding the saw,
they cannot be cut by the blade.
Keep your body positioned to either side of the
saw blade, but not in line with the saw blade.
KICKBACK could cause the saw to jump backwards.
See Pages 14 and 15.
■
Do not reach underneath the work. The guard
cannot protect you from the blade below the work.
Check the lower guard for proper closing before
each use. Do not operate saw if lower guard does
not move freely and close instantly. Never clamp
or tie the lower guard into the open position . If
saw is accidentally dropped, lower guard may be bent.
Raise lower guard with the lower blade guard handle
and make sure it moves freely and does not touch the
blade or any other part, in all angles and depths of cut.
Check the operation and condition of the lower
guard spring. If the guard and the spring are not
operating properly, they must be serviced before
use. Lower guard may operate sluggishly due to
damaged parts, gummy deposits, or a buildup of
debris.
Lower guard should be retracted manually only for
special cuts such as “Pocket Cuts” and “Compound Cuts”. Raise lower guard by lower blade
guard handle. As soon as blade enters the material, lower guard must be released. For all other
sawing, the lower guard should operate automatically.
Always observe that the lower guard is covering
the blade before placing saw down on bench or
floor. An unprotected, coasting blade will cause the
saw to walk backwards, cutting whatever is in its path.
Be aware of the time it takes for the blade to stop after
switch is released.
NEVER hold piece being cut in your hands or
across your leg. It is important to support the work
properly to minimize body exposure, blade binding, or
loss of control.
Hold tool by insulating gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring. Contact with a “live” wire
will also make exposed metal parts to the tool “live”
and shock the operator.
When ripping always use a rip fence or a straight
edge guide. This improves the accuracy of cut and
reduces the chance of blade binding.
Always use blade with correct size and shape
(diamond vs. round) arbor holes. Blades that do not
match the mounting hardware of the saw will run
eccentrically, causing loss of control.
■
■
■
■
■
■
■
4
Never use damaged or incorrect blade washers or
bolts. The blade washers and bolt were specially
designed for your saw, or optimum performance and
safety of operation.
Causes and Operator Prevention of Kickback:
Kickback is a sudden reaction to a pinched, bound, or
misaligned saw blade, causing an uncontrolled saw to
lift up and out of the workpiece toward the operator.
When the blade is pinched or bound tightly by the kerf
closing down, the blade stalls and the motor reaction
drives the unit rapidly back toward the operator.
If the blade becomes twisted or misaligned in the cut,
the teeth at the back edge of the blade can dig into the
top surface of the wood causing the blade to climb out
of the kerf and jump back toward the operator.
Kickback is a result of tool misuse and/or incorrect
operating procedures or conditions and can be
avoided by taking proper precautions as given below:
Maintain a firm grip on the saw and position your
body and arm in a way that allows you to resist
KICKBACK forces. KICKBACK forces can be controlled by the operator, if proper precautions are taken.
When blade is binding, or when interrupting a cut
for any reasons, release the trigger and hold the
saw motionless in the material until the blade
comes to a complete stop. Never attempt to
remove the saw from the work or pull the saw
backward while the blade is in motion or KICKBACK may occur. Investigate and take corrective
actions to eliminate the cause of blade binding.
When restarting a saw in the workpiece, center the
saw blade in the kerf and check that teeth are not
engaged into the material. If saw blade is binding, it
may walk up or KICKBACK from the workpiece as the
saw is restarted.
Support large panels to minimize the risk of blade
pinching and KICKBACK. Large panels tend to sag
under their own weight. Supports must be placed
under the panel on both sides, near the line of cut and
near the edge of the panel.
Do not use dull or damaged blades. Unsharpened
or improperly set blades produce narrow kerf causing
excessive friction, blade binding, and KICKBACK.
Blade depth and bevel adjusting locking levers
must be tight and secure before making cut. If
blade adjustment shifts while cutting, it will cause
binding and KICKBACK.
Use extra caution when making a “Pocket Cut”
into existing walls or other blind areas. The protruding blade may cut objects that can cause KICKBACK.
SPECIFIC SAFETY RULES AND/OR SYMBOLS
Important Safety Instructions For Charger
■
■
■
■
■
■
■
■
■
■
Save these instructions. This manual contains
important safety and operating instructions for
battery charger item number 9-11040 (981399-001).
Following this rule will reduce the risk of electric shock,
fire, or serious personal injury.
Before using battery charger, read all instructions
and cautionary markings in this manual, on battery
charger, and product using battery charger. Following this rule will reduce the risk of electric shock, fire,
or serious personal injury.
To reduce the risk of injury, charge only nickelcadmium and nickel metal hydride type rechargeable batteries. Other types of batteries may burst
causing personal injury and damage. Following this
rule will reduce the risk of electric shock, fire, or
serious personal injury.
Do not expose charger to rain or snow. Following
this rule will reduce the risk of electric shock, fire, or
serious personal injury.
Use of an attachment not recommended or sold by
the battery charger manufacturer may result in a
risk of fire, electric shock, or injury to persons.
Following this rule will reduce the risk of electric shock,
fire, or serious personal injury.
To reduce the risk of damage to charger body and
cord, pull by charger plug rather than cord when
disconnecting charger. Following this rule will reduce
the risk of serious personal injury.
Make sure cord is located to that it will not be
stepped on, tripped over, or otherwise subjected to
damage or stress. Following this rule will reduce the
risk of serious personal injury.
An extension cord should not be used unless
absolutely necessary. Use of improper extension
cord could result in a risk of fire and electric shock. If
extension cord must be used, make sure:
a. That pins on plug of extension cord are the same
number, size and shape as those of plug on
charger.
b. That extension cord is properly wired and in good
electrical condition; and
c. That wire size is large enough for AC ampere rating
of charger as specified below:
Cord Length (Feet)
25´
50´
100´
Cord Size (AWG)
16
16
16
Note: AWG = American Wire Gage
Do not operate charger with a damaged cord or
plug. If damaged, have replaced immediately by a
qualified serviceman. Following this rule will reduce
the risk of electric shock, fire, or serious personal
injury.
■
■
■
■
■
Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in any
way; take it to a qualified serviceman. Following this
rule will reduce the risk of electric shock, fire, or
serious personal injury.
Do not disassemble charger; take it to a qualified
serviceman when service or repair is required.
Incorrect reassembly may result in a risk of electric shock or fire. Following this rule will reduce the
risk of electric shock, fire, or serious personal injury.
To reduce the risk of electric shock, unplug
charger from outlet before attempting any maintenance or cleaning. Turning off controls will not
reduce this risk. Following this rule will reduce the
risk of electric shock, fire, or serious personal injury.
Do not use charger outdoors. Following this rule will
reduce the risk of electric shock, fire, or serious
personal injury.
Disconnect charger from power supply when not
in use. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
DANGER: RISK OF ELECTRIC SHOCK. DO NOT
TOUCH UNINSULATED PORTION OF OUTPUT
CONNECTOR OR UNINSULATED BATTERY TERMINAL.
Save these instructions. Refer to them frequently
and use them to instruct others who may use this
tool. If you loan someone this tool, loan them
these instructions also. Following this rule will
reduce the risk of electric shock, fire, or serious
personal injury.
WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement
and other masonry products, and
• arsenic and chromium from chemicallytreated lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
5
SYMBOLS
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
A
Amperes
Current
Hz
Hertz
Frequency (cycles per second)
min
Minutes
Time
Alternating Current
Type or a characteristic of current
---
Direct Current
Type or a characteristic of current
n0
No Load Speed
Rotational speed, at no load
.../min
Revolutions or Reciprocation Per Minute
Revolutions, strokes,
surface speed, orbits etc. per minute
Safety Alert Symbol
Indicates danger, warning or caution.
It means attention!!! Your safety is
involved.
FEATURES
DEFINITIONS
A)
DANGER: Failure to obey a safety warning will result in serious injury to yourself or to others.
Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
B)
WARNING: Failure to obey a safety warning can result in serious injury to yourself or to others.
Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
C)
CAUTION: Failure to obey a safety warning may result in property damage or personal injury
to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric
shock and personal injury.
D)
NOTE: Advises you of information or instructions vital to the operation or maintenance of the
equipment.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety goggles or
safety glasses with side shields and a full face shield when needed. We recommend Wide Vision
Safety Mask for use over eyeglasses or standard safety glasses with side shields, available at Sears
Retail Stores.
6
FEATURES
KNOW YOUR TRIM SAW
APPLICATIONS
See Figure 1.
Before attempting to use your trim saw, familiarize yourself
with all operating features and safety requirements.
Features include easily operated bevel cut and depth of
cut adjustment mechanisms; positive 0° bevel stop;
spindle lock; and blade wrench storage.
(Use only for the purposes listed below)
■ Cutting all types of wood products (lumber, plywood,
paneling).
WARNING: If any parts are missing, do not operate
your saw until the missing parts are replaced. Failure to
do so could result in possible serious personal injury.
WARNING: Carefully read through this entire
PRODUCT SPECIFICATIONS:
owner’s manual before using your new trim saw. Pay
close attention to the Rules For Safe Operation,
Warnings and Cautions. If you use your trim saw
properly and only for what it is intended, you will enjoy
years of safe, reliable service.
TRIM SAW
Blade Diameter
Blade Arbor
Your trim saw has been shipped completely assembled
except for the blade. Inspect it carefully to make sure no
breakage or damage has occurred during shipping. If any
parts are damaged or missing, contact your nearest Sears
Retail Store to obtain replacement parts before attempting
to operate saw. A blade, blade wrench (5 mm hex key), rip
guide (edge guide) and this owner's manual are also
included.
Cutting Depth at 45°
1-5/8 in. (42 mm)
No load Speed
2,500 RPM
Motor
18 Volts DC
Charging Voltage
Charge Rate
BATTERY PACK
SWITCH
Your saw is equipped with a lock-off button which reduces
the possibility of accidental starting. The lock-off button is
located on the handle above the switch trigger. You must
depress the lock-off button in order to pull the switch
trigger. The lock resets each time the trigger is released.
Note: You can depress the lock-off button from either the
left or right side.
7
5/8 in. (16 mm)
2-1/8 in. (54 mm)
Input
make you careless. Remember that a careless fraction
of a second is sufficient to inflict severe injury.
6-1/2 in. (165 mm)
Cutting Depth at 90°
CHARGER
WARNING: Do not allow familiarity with your saw to
315.271190
ITEM NO. 9-11040
(981399-001)
120 v, 60 Hz, AC only
9.6 - 24 Volts
1 Hour
ITEM NO. 9-11034
(981404-001)
FEATURES
BLADE WRENCH
(5 mm HEX KEY)
DEPTH OF
CUT ADJUSTMENT
(DEPTH ADJUSTMENT KNOB)
BLADE WRENCH
STORAGE AREA
SWITCH
TRIGGER
LOCK-OFF
BUTTON
BATTERY
PACK
SPINDLE
LOCK BUTTON
RIP
GUIDE SCREW
(WING SCREW)
UPPER
BLADE GUARD
50
45
30
2
3
3
LOWER BLADE
GUARD HANDLE
1
2
1
BEVEL CUT ADJUSTMENT
(BEVEL ADJUSTMENT KNOB)
30
45
4
1
5
BASE
ASSEMBLY
LOWER
BLADE GUARD
0
BLADE
RIP GUIDE
Fig. 1
8
FEATURES
LED FUNCTION OF CHARGER
See Figure 4.
CHARGER
Your charger has a “key hole” hanging feature for convenient, space saving storage. Therefore, if desired, you can
mount your charger to a wall. Screws should be installed
so that center distances are 4-1/8 inches apart.
®
YELLOW LIGHT “ON” AND RED
LIGHT FLASHING INDICATES
DEFECTIVE BATTERY PACK
MOUNTING CHARGER
+
Ch
a
Fl rgin
So ashin g
ft S g
t
art
Re
ad
y
B
Ba ad
tte
ry
AL E
RS RG
IVE HA
UN ST C
FA
RED LIGHT “ON”
INDICATES FAST
CHARGING MODE
4-1/8 in.
GREEN LIGHT “ON” INDICATES FULLY
CHARGED AND SLOW CHARGING
TO MAINTAIN BATTERY PACK
Fig. 2
BATTERY PACK SHOWN ATTACHED TO CHARGER
BACK SIDE OF CHARGER
UNIV
FAST ERSAL
CHAR
GE
+
Bad
Batte
®
ry
Chargin
g
Flashing
Soft Sta
rt
Ready
CHARGER
BATTERY PACK SHOWN
IN CHARGER
Fig. 3
9
Fig. 4
ASSEMBLY
WARNING: Always remove battery pack from your
SPINDLE
LOCK BUTTON
saw when you are assembling parts, making
adjustments, assembling or removing blades,
cleaning, or when not in use. Removing battery pack
will prevent accidental starting that could cause
serious personal injury.
LOWER BLADE
GUARD HANDLE
Note: Your saw is assembled with the battery pack
attached.
BLADE
50
45
TO REMOVE BATTERY PACK
30
2
1
0
45
1
3
3
See Figure 5.
■ Depress latch located on front of battery pack (1) to
release battery pack.
■ Pull on battery pack (2) to remove from saw.
INNER
BLADE WASHER
DEPRESS LATCH TO
RELEASE BATTERY PACK
OUTER
BLADE WASHER
BLADE SCREW
Fig. 6
1
■ Remove blade wrench (5 mm hex key) from storage
area. See Figure 1.
■ Depress spindle lock button and remove blade screw
and outer blade washer. See Figure 6.
Note: Turn blade screw clockwise to remove.
■ Wipe a drop of oil onto inner blade washer and outer
blade washer where they contact blade.
PULL TO
REMOVE
2
BATTERY PACK
Fig. 5
WARNING: If inner blade washer has been reTO ASSEMBLE BLADE
moved, replace it before placing blade on spindle.
Failure to do so could cause an accident since blade
will not tighten properly.
See Figure 6.
WARNING: A 6-1/2 in. (165 mm) blade is the
■ Fit saw blade inside lower blade guard and onto
spindle.
Note: The saw teeth point upward at the front of saw
as shown in figure 6.
■ Replace outer blade washer.
maximum blade capacity of your saw. Never use a
blade that is too thick to allow outer blade washer to
engage with the flats on the spindle. Larger blades
will come in contact with the blade guard, while
thicker blades will prevent blade screw from securing
blade on spindle. Either of these situations could
result in a serious accident.
■ Depress spindle lock button, then replace blade screw.
Tighten blade screw securely.
Note: Turn blade screw counterclockwise to tighten.
■ Return blade wrench to storage area.
■ Remove battery pack from saw.
WARNING: Failure to remove battery pack from
REMEMBER: Never use a blade that is too thick to
allow the outer blade washer to engage with the flats
on the spindle.
saw could result in accidental starting causing
possible serious personal injury.
■ Locate latch on end of battery pack and depress to
release battery pack from your saw. See Figure 5.
10
ASSEMBLY
TO REMOVE BLADE
TO ATTACH BATTERY PACK TO TRIM SAW
See Figure 7.
■ Remove battery pack from saw.
See Figure 8.
Note: Battery pack is shipped in a low charge condition.
Therefore, it must be charged prior to use. Refer to page
12, “CHARGING BATTERY PACK” for charging
instructions.
WARNING: Failure to remove battery pack from
saw could result in accidental starting causing
possible serious personal injury.
■ Remove blade wrench from storage area. See Figure 1.
■ Position saw as shown in figure 8, depress spindle lock
button, and remove blade screw.
Note: Turn blade screw clockwise to remove.
■ Remove outer blade washer. See Figure 8.
Note: Blade can be removed at this point.
■
Align raised ribs on battery pack with grooves on
bottom of saw, then attach battery pack to saw as
shown in figure 8.
■
Make sure the latch on battery pack snaps in place
and battery pack is secured to saw before beginning
operation.
LATCH
RAISED RIBS
SPINDLE
LOCK BUTTON
TO LOOSEN
GROOVES
50
45
30
2
BATTERY PACK
1
0
45
1
3
30
2
3
50
45
BLADE
SCREW
45
1
0
1
BLADE
WRENCH
Fig. 8
TO TIGHTEN
CAUTION: When attaching battery pack to your
saw, be sure raised ribs and grooves align properly
and latch snaps into place properly. Improper
assembly can cause damage to saw and battery
pack.
Fig. 7
11
OPERATION
WARNING: Always wear safety goggles or safety
glasses with side shields when operating tools.
Failure to do so could result in objects being thrown
into your eyes, resulting in possible serious injury.
CHARGING BATTERY PACK
The battery pack for this tool has been shipped in a low
charge condition to prevent possible problems. Therefore,
you should charge it until light on front of charger changes
from red to green.
Note: Batteries will not reach full charge the first time they
are charged. Allow several cycles (cutting followed by
recharging) for them to become fully charged.
■
■
TO CHARGE
■
■ Charge battery pack only with the charger provided.
■ Make sure power supply is normal house voltage,
120 volts, 60 Hz, AC only.
■ Connect charger to power supply.
■ Attach battery pack to charger by aligning raised ribs
on battery pack with grooves in charger, then slide
battery back onto charger. See Figure 9.
■
■
LED FUNCTION OF CHARGER
BATTERY
PACK
LED WILL BE LIGHTED TO INDICATE STATUS OF
CHARGER AND BATTERY PACK:
■ Red LED Lighted = Fast Charging Mode.
■ Green LED Lighted = Fully Charged And Slow
Charging To Maintain Battery Pack.
■ Red LED Flashing = Hot Or Deeply Discharged
Battery Pack. Also Defective Battery Pack After 1 Hour.
■ Yellow LED Lighted and Red LED Flashing =
Defective Battery Pack.
TO
REMOVE
®
CHARGER
AL E
RS RG
IVE HA
UN ST C
FA
Fla in
So shin g
ft S g
tar
t
arg
IMPORTANT INFORMATION FOR RECHARGING
HOT BATTERIES
Re
ad
y
Ch
+
B
Ba ad
tte
ry
TO
ATTACH
GROOVES
If after one hour red light is still flashing, this indicates
a defective battery pack and should be replaced.
Green light on indicates battery pack is fully charged
and slow charging to maintain battery pack.
Yellow light on and red light flashing indicates defective
battery pack. Return battery pack to your nearest
Sears Repair Center for checking or replacing.
When your battery pack becomes fully charged, the
red light will turn OFF and the green light will turn ON.
After normal usage, 1 hour of charging time is required
to be fully charged. A minimum charge time of 1-1/2
hours is required to recharge a completely discharged
tool.
The battery pack will become slightly warm to the
touch while charging. This is normal and does not
indicate a problem.
Do not place charger in an area of extreme heat or
cold. It will work best at normal room temperature.
When the batteries become fully charged, unplug your
charger from power supply and remove the battery
pack.
Under extreme continuous use, the batteries in your
battery pack will become hot. You should let a hot battery
pack cool down for approximately 1 hour before attempting to recharge. When the battery pack becomes discharged and is hot, this will cause the red light on your
battery charger to flash. When battery pack cools down,
red light will glow continuously indicating fast charging
mode, 1 hour charge time. Once the battery pack cools
down, it will recharge battery pack in fast charging mode
as normal.
Note: This situation only occurs when extreme continuous
use of your saw causes the batteries to become hot. It
does not occur under normal circumstances. Refer to
"CHARGING BATTERY PACK" for normal recharging of
batteries. If the charger does not charge your battery pack
under normal circumstances, return both the battery pack
and charger to your nearest Sears repair center for
electrical check.
Fig. 9
■ Red light should turn on. Red light indicates fast
charging mode.
If red light is flashing, this indicates battery pack is
deeply discharged or hot.
If battery pack is hot, red light should become steady
after battery pack has cooled down.
If battery pack is deeply discharged, red light should
become steady after voltage has increased, normally
within 60 minutes.
12
OPERATION
Never use saw when guard is not operating correctly.
Guard should be checked for correct operation before
each use. If you drop your saw, check the lower blade
guard and bumper for damage at all depth settings
before reuse. Note: The guard is operating correctly
when it moves freely and readily returns to the closed
position. If for any reason your lower blade guard
does not close freely, take it to the nearest Sears Parts
and Repair Center for service before using.
SAW BLADES
The best of saw blades will not cut efficiently if they are
not kept clean, sharp, and properly set. Using a dull blade
will place a heavy load on your saw and increase the
danger of kickback. Keep extra blades on hand, so that
sharp blades are always available.
Gum and wood pitch hardened on blades will slow your
saw down. Use gum and pitch remover, hot water, or
kerosene to remove these accumulations. Do not use
gasoline.
LOWER BLADE GUARD
IS IN UP POSITION
WHEN MAKING A CUT
BLADE GUARD SYSTEM
The lower blade guard attached to your trim saw is
there for your protection and safety. It should never be
altered for any reason. If it becomes damaged or
begins to return slow or sluggish, do not operate your
saw until the damage has been repaired or replaced.
Always leave guard in operating position when using
saw.
DANGER: When sawing through workpiece, lower
blade guard does not cover blade on the underside of
workpiece. Since blade is exposed on underside of
workpiece, keep hands and fingers away from cutting
area. Any part of your body coming in contact with
moving blade will result in serious injury.
See Figure 10.
BLADE EXPOSED ON
UNDERSIDE OF WORKPIECE
13
Fig. 10
OPERATION
KICKBACK
TO LESSEN THE CHANCE OF KICKBACK:
See Figure 11.
■ Always keep the correct blade depth setting – the
correct blade depth setting for all cuts should not
exceed 1/4 in. below the material to be cut. See Figure
13. One blade tooth below the material to be cut works
best for most efficient cutting action.
KICKBACK
Fig. 11
BLADE SET TOO DEEP
The best guard against kickback is to avoid dangerous
practices.
Kickback occurs when the blade stalls rapidly and the saw
is driven back towards you. Blade stalling is caused by any
action which pinches the blade in the wood.
CORRECT BLADE DEPTH SETTING =
BLADE EXPOSED ONE BLADE TOOTH
BELOW THE MATERIAL TO BE CUT
DANGER: Release switch immediately if blade binds
or saw stalls. Kickback could cause you to lose
control of your saw. Loss of control can lead to
serious injury.
Fig. 13
■ Inspect the workpiece for knots or nails before
beginning a cut. Never saw into a knot or nail.
■ Make straight cuts. Always use a straight edge guide
when rip cutting. This helps prevent twisting the blade
in the cut.
■ Always use clean, sharp and properly set blades.
Never make cuts with dull blades.
■ To avoid pinching the blade, support the workpiece
properly before beginning a cut. The right and wrong
ways to support large pieces of work are shown in
figures 12 and 14.
KICKBACK IS CAUSED BY:
■
■
■
■
Incorrect blade depth setting. See Figure 11.
Sawing into knots or nails in workpiece.
Twisting blade while making a cut.
Making a cut with a dull, gummed up, or improperly set
blade.
■ Incorrectly supporting workpiece. See Figure 12.
■ Forcing a cut.
■ Cutting warped or wet lumber.
■ Tool misuse or incorrect operating procedures.
50
45
0
22.5
1
0
50
45
0
22.5
1
0
RIGHT
WRONG
Fig. 12
14
Fig. 14
OPERATION
■ When making a cut use steady, even pressure. Never
force cuts.
■ Do not cut warped or wet lumber.
■ Always hold your saw firmly with both hands and keep
your body in a balanced position so as to resist the
forces of kickback should it occur.
STARTING A CUT
Know the right way to use your saw.
See Figure 16.
When using your saw, always stay alert and exercise
control. Do not remove your saw from workpiece
while the blade is moving.
DEPTH OF CUT ADJUSTMENT
50
45
Always keep correct blade depth setting. The correct
blade depth setting for all cuts should not exceed 1/4 inch
below the material to be cut. More blade depth will
increase the chance of kickback and cause the cut to be
rough. One blade tooth below the material to be cut works
best for most efficient cutting action.
3
30
2
45
1
3
TO ADJUST BLADE DEPTH
1
0
■ Remove battery pack from saw.
WARNING: Failure to remove battery pack from
Fig. 16
saw could result in accidental starting causing
possible serious personal injury.
Never use your saw as shown in figure 17.
TO RAISE
SAW
TO
TIGHTEN
50
45
30
2
1
0
45
1
3
3
TO LOWER
SAW
DEPTH
ADJUSTMENT
KNOB
BASE
ASSEMBLY
TO
LOOSEN
Fig. 15
■ Loosen depth adjustment knob. See Figure 15.
■ Hold base flat against the workpiece and raise or lower
saw until the required depth is reached.
■ Tighten depth adjustment knob securely.
WRONG
Fig. 17
Never place your hand on the workpiece behind your
saw while making a cut.
WARNING: To make sawing easier and safer,
always maintain proper control of your saw. Loss of
control of your saw could cause an accident resulting
in possible serious injury.
15
OPERATION
TO HELP MAINTAIN CONTROL:
Hold your saw firmly with both hands.
See Figure 19.
■ Always support your workpiece near the cut.
■ Support your workpiece so the cut will be on your left.
■ Clamp your workpiece so it will not move during the
cut.
50
45
Place your workpiece with its good side down.
Note: The good side is the side on which appearance is
important.
Before beginning a cut, draw a guideline along the desired
line of cut. Then place front edge of base on that part of
your workpiece that is solidily supported. See Figure 16.
Never place your saw on that part of the workpiece
that will fall off when the cut is made. See Figure 18.
1
0
45
1
3
3
30
2
RIGHT
Fig. 19
Depress the lock-off button and squeeze the switch trigger
to start your saw. Always let the blade reach full speed,
then guide your saw into the workpiece.
50
45
30
2
WARNING: The blade coming in contact with the
1
0
45
1
3
3
workpiece before it reaches full speed could cause
your saw to "kickback" towards you resulting in
serious injury.
When making a cut use steady, even pressure. Forcing
causes rough cuts, could shorten the life of your saw and
could cause "kickback."
WRONG
REMEMBER:
When sawing through work, the lower blade guard
does not cover the blade, exposing it on the
underside of work. Keep your hands and fingers away
from cutting area. Any part of your body coming in
contact with the moving blade will result in serious
injury.
After you complete your cut release the trigger and allow
the blade to come to a complete stop. Do not remove
your saw from workpiece while the blade is moving.
Fig. 18
CAUTION: When lifting your saw from the
workpiece, the blade is exposed on the underside of
your saw until the lower blade guard closes. Make
sure lower blade guard is closed before setting your
saw down on work surface.
16
OPERATION
TO CROSS CUT OR RIP CUT
A width of cut scale has been provided on the base of
your saw. When making straight cross cuts or rip cuts, the
scale can be used to measure up to four inches to the
right side of the blade. It can be used to measure up to
one inch to the left side of the blade.
When making a cross cut or rip cut, align your line of cut
with the outer blade guide notch on the saw base as
shown in figure 20.
TOP VIEW OF SAW
GUIDELINE
RIP GUIDE (EDGE GUIDE)
Use the rip guide provided with your saw when making
wide rip cuts. A five inch scale has been provided on the
rip guide. When using the width of cut scale on the base
in combination with the rip guide, cuts can be made up to
6 in. to the left of the rip guide or 8-7/8 in. to the right of
the rip guide.
The rip guide helps prevent the blade from twisting in a
cut. The blade twisting in a cut can cause kickback.
BLADE
GUIDE NOTCH
1 0
45 1
2
FRONT
OF SAW
3
TO ASSEMBLE RIP GUIDE
■ Remove battery pack from saw.
4
WARNING: Failure to remove battery pack from
saw could result in accidental starting causing
possible serious personal injury.
ALIGN OUTER BLADE GUIDE NOTCH ON SAW BASE WITH LINE
OF CUT AS SHOWN WHEN MAKING CROSS CUTS OR RIP CUTS
Fig. 20
Since blade thicknesses vary, always make a trial cut in
scrap material along a guideline to determine how much,
if any, the guideline must be offset to produce an accurate
cut.
Note: The distance from the line of cut to the guideline is
the amount you should offset the guideline.
RIP
GUIDE SCREW
(WING SCREW)
50
45
30
2
WIDTH OF CUT SCALE
30
45
4
1
5
3
3
See Figure 21.
0
1
2
1
RIP GUIDE
(EDGE GUIDE)
BASE
ASSEMBLY
PLACE RIP
GUIDE THRU HOLES
■ Place rip guide through holes in saw base as shown in
figure 22.
■ Adjust rip guide to the width needed.
■ Tighten rip guide screw (wing screw) securely.
50
45
3
30
2
When using a rip guide, position the face of the rip guide
firmly against the edge of workpiece. This makes for a
true cut without pinching the blade. The guiding edge of
workpiece must be straight for your cut to be straight. Use
caution to prevent the blade from binding in the cut.
1
0
45
1
3
WIDTH OF
CUT SCALE
Fig. 22
BLADE
Fig. 21
17
OPERATION
Align your line of cut with the inner blade guide notch on
the saw base when making 45° bevel cuts.
Since blade thicknesses vary and different angles
require different settings, always make a trial cut in
scrap material along a guideline to determine how
much you should offset the guideline on the board to
be cut.
When making a bevel cut hold your saw firmly with both
hands as shown in figure 25.
ALTERNATIVE RIP METHOD
See Figure 23.
Using C-clamps, firmly clamp a straight edge to the
workpeice and guide the saw along the straight edge to
achieve a straight rip cut. Do not bind the blade in the cut.
ALTERNATIVE METHOD FOR RIP CUTTING
WORKPIECE
STRAIGHT
EDGE
50
45
30
2
50
45
1
0
45
1
1
0
3
45
1
3
3
3
30
2
NOTE: C-CLAMP BOTH ENDS OF
STRAIGHT EDGE BEFORE MAKING CUT
LOWER
BLADE GUARD
Fig. 25
Fig. 23
Rest the front edge of the base on the workpiece.
Depress the lock-off button and squeeze the switch trigger
to start your saw. Always let the blade reach full speed,
then guide your saw into the workpiece.
TO BEVEL CUT
The angle of cut of your saw may be adjusted to any
desired setting between zero and 50°. Note: When
making cuts at 50°, blade should be set at full depth of
cut.
When making 45° bevel cuts, there is a notch in the saw
base to help you line up the blade with the line of cut.
See Figure 24.
WARNING: The blade coming in contact with the
workpiece before it reaches full speed could cause
saw to "kickback" toward you resulting in serious
injury.
BEVEL
ADJUSTMENT
KNOB
BEVEL
SCALE
After you complete your cut release the trigger and allow
the blade to come to a complete stop. After the blade has
stopped, lift your saw from the workpiece.
TO ADJUST BEVEL SETTING
■ Remove battery pack from saw.
50
45
30
2
WARNING: Failure to remove battery pack from
45 1
2
3
BLADE
GUIDE NOTCH
1 0
1
0
45
1
3
3
saw could result in accidental starting causing
possible serious personal injury.
■ Loosen bevel adjustment knob. See Figure 24.
■ Raise motor housing end of saw until you reach desired
angle setting on bevel scale. See Figure 24.
■ Tighten bevel adjustment knob securely.
GUIDELINE
ALIGN INNER BLADE GUIDE NOTCH ON SAW BASE WITH
LINE OF CUT AS SHOWN WHEN MAKING 45° BEVEL CUTS
Fig. 24
WARNING: Attempting bevel cut without knob
securely tightened can result in serious injury.
18
OPERATION
POSITIVE 0° BEVEL STOP
■ Turn screw and adjust base until square with saw
blade.
See Figure 26.
■ Tighten hex nut and bevel adjustment knob securely.
ADJUSTMENT
SCREW
45
50
30
1
22
15
WARNING: Attempting to make cuts without bevel
BEVEL
ADJUSTMENT
KNOB
adjustment knob securely tightened can result in
serious injury.
0
45
TO POCKET CUT
1
2
See Figure 27.
3
4
HEX NUT
CARPENTER'S
SQUARE
WARNING: Always adjust bevel setting to zero before
POSITIVE 0 °
BEVEL STOP
making a pocket cut. Attempting a pocket cut at any
other setting can result in loss of control of your saw
possibly causing serious injury.
BLADE
Adjust the bevel setting to zero, set blade to correct blade
depth setting, and swing the lower blade guard up using
the lower blade guard handle.
Always raise the lower blade guard with the handle to
avoid serious injury.
While holding lower blade guard by the handle, firmly rest
the front of the base flat against the workpiece with the
rear of the handle raised so the blade does not touch the
workpiece. See Figure 27.
Fig. 26
LOWER BLADE
GUARD HANDLE
Your saw has a positive 0° bevel stop, that has been
factory adjusted to assure 0° angle of your saw blade
when making 90° cuts. However, misalignment can occur
during shipping.
TO CHECK
■ Remove battery pack from saw.
50
45
2
30
3
WARNING: Failure to remove battery pack from
1
3
saw could result in accidental starting causing
possible serious personal injury.
45
1
0
■ Place your saw in an upside down position on
workbench. See Figure 26.
■ Using a carpenter's square, check squareness of saw
blade to the base of your saw.
POCKET CUT
LOWER BLADE GUARD
Fig. 27
Depress the lock-off button and squeeze the switch
trigger to start your saw. Always let the blade reach
full speed then slowly lower blade into the
workpiece until base is flat against workpiece.
After you complete your cut release the trigger and allow
the blade to come to a complete stop. After the blade
has stopped, remove it from the workpiece. Corners
may then be cleared out with a hand saw or sabre saw.
TO ADJUST
■ Remove battery pack from saw.
WARNING: Failure to remove battery pack from
saw could result in accidental starting causing
possible serious personal injury.
■ Loosen bevel adjustment knob.
■ Loosen hex nut securing adjustment screw.
WARNING: Never tie the lower blade guard in a
raised position. Leaving the blade exposed could
lead to serious injury.
19
MAINTENANCE
Do not abuse power tools. Abusive practices can damage
tool as well as workpiece.
WARNING: When servicing, use only identical
Craftsman replacement parts. Use of any other part
may create a hazard or cause product damage.
Only the parts shown on parts list, page 23, are intended
to be repaired or replaced by the customer. All other parts
should be replaced at a Sears Service Center.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
WARNING: Do not attempt to modify this tool or
create accessories not recommended for use with
this tool. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious personal injury.
WARNING: Do not at any time let brake fluids,
gasoline, petroleum-based products, penetrating oils,
etc. come in contact with plastic parts. They contain
chemicals that can damage, weaken or destroy
plastic.
BATTERIES
■
Your saw's battery pack is equipped with 15 nickelcadmium rechargeable batteries. Length of service from
each charging will depend on the type of work you are
doing.
The batteries in this tool have been designed to provide
maximum trouble free life. However, like all batteries, they
will eventually wear out. Do not disassemble battery pack
and attempt to replace the batteries. Handling of these
batteries, especially when wearing rings and jewelry,
could result in a serious burn.
To obtain the longest possible battery life, we suggest the
following:
C YC
R ER B R CL E
■
■
To preserve natural resources, please
recycle or dispose of batteries properly.
Store and charge your batteries in a cool area.
Temperatures above normal room temperature will
shorten battery life.
Never store batteries in a discharged condition.
Recharge them immediately after they are
discharged.
All batteries gradually lose their charge. The higher
the temperature the quicker they lose their charge. If
you store your tool for long periods of time without
using it, recharge the batteries every month or two.
This practice will prolong battery life.
BATTERY PACK REMOVAL AND PREPARATION
FOR RECYCLING
WARNING: Upon removal, cover the battery pack's
37
1.8
This product contains nickel-cadmium
battery. Local, state, or federal laws
N i Cd
may prohibit disposal of nickel-cadmium
00
8
.822.8
batteries in ordinary trash.
Consult your local waste authority for information
regarding available recycling and/or disposal options.
terminals with heavy duty adhesive tape. Do not
attempt to destroy or disassemble battery pack or
remove any of its components. Nickel-cadmium
batteries must be recycled or disposed of properly.
Also, never touch both terminals with metal objects
and/or body parts as short circuit may result. Keep
away from children. Failure to comply with these
warnings could result in fire and/or serious injury.
20
ACCESSORIES
The following recommended accessories are currently available at Sears Retail Stores.
■ 6-1/2 in. (165 mm) Thin Kerf Blade
WARNING: The use of attachments or accessories not listed might be hazardous.
WARRANTY
FULL ONE YEAR WARRANTY ON
PROFESSIONAL CORDLESS TRIM SAW
If this CRAFTSMANProfessional Cordless Trim Saw fails due to a defect in material or workmanship within one year
from the date of purchase, Sears will repair it, free of charge.
WARRANTY SERVICE IS AVAILABLE BY SIMPLY RETURNING THE TOOL TO THE NEAREST SEARS STORE OR
SEARS SERVICE CENTER IN THE UNITED STATES.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179
SAVE THESE INSTRUCTIONS
21
CRAFTSMAN 18 VOLTS PROFESSIONAL CORDLESS TRIM SAW – MODEL NUMBER 315.271190
®
2
1
Ch
a
Fl rgin
So ashin g
ft S g
tar
t
ad
y
Re
+
B
Ba ad
tte
ry
AL E
RS RG
IVE HA
UN ST C
FA
3
4
5
7
6
20
19
11
18
12
8 9
10
17
21
13
24
16
25
23
14
22
9
18
30
22
.5
15
4
31
32
1
2
1
29
0
3
3
2
30
0
33
1
0
45
22
15
5
505
4
26
27
28
21
22
22
CRAFTSMAN 18 VOLTS PROFESSIONAL CORDLESS TRIM SAW – MODEL NUMBER 315.271190
The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your
CORDLESS TRIM SAW or when ordering repair parts.
SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS
PARTS LIST
Key
No.
Part
Number
1
982174-001
2
** Item No. 9-11034
Key
No.
Part
Number
Data Plate ................................................... 1
18
975544-000
Lock Nut ...................................................... 2
Battery Pack (981404-001) ......................... 1
19
982164-001
Spring .......................................................... 1
Description
Quan.
Description
Quan.
3
982158-001
Upper Blade Guard ..................................... 1
20
982165-001
Spindle Lock ................................................ 1
4
982159-001
Upper Blade Guard Screw .......................... 4
21
982166-001
Knob ............................................................ 2
Charger (981399-001) ................................ 1
22
982167-001
Washer ........................................................ 2
5
** Item No. 9-11040
6
982160-001
Spring .......................................................... 1
23
982168-001
Carriage Bolt (M6 x 12 mm) ........................ 1
7
982161-001
Lower Blade Guard ..................................... 1
24
975558-000
Screw .......................................................... 1
8
982162-001
Guard Retainer ........................................... 1
25
975559-000
Hex Nut ....................................................... 1
9
982163-001
Guard Retainer Screw ................................ 4
26
982169-001
Wing Screw ................................................. 1
10
6112003
Inner Blade Washer .................................... 1
27
982170-001
Washer ........................................................ 1
11
982427-001
Lower Blade Guard Handle ........................ 1
28
975552-000
Spring .......................................................... 1
12
982428-001
Screw .......................................................... 1
29
982171-001
Base Screw ................................................. 1
Saw Blade ................................................... 1
30
982172-001
Base Assembly ........................................... 1
13
*
14
975533-000
Outer Blade Washer ................................... 1
31
982173-001
Carriage Bolt (M6 x 100 mm) ...................... 1
15
975532-000
Blade Screw ................................................ 1
32
975553-000
Blade Wrench (5 mm Hex Key) .................. 1
16
982426-001
Bumper Screw............................................. 1
33
975554-000
Rip Guide .................................................... 1
17
982425-001
Bumper ........................................................ 1
34
982175-001
Carrying Case – Not Shown
972000-765
Owner’s Manual
* Available At Your Nearest Sears Catalog Order Or Retail Store
** Can Be Purchased Thru RSOS (Retail Special Order System)
23
Get it fixed, at your home or ours!
For repair of major brand appliances in your own home…
no matter who made it, no matter who sold it!
1-800-4-MY-HOME SM Anytime, day or night
(1-800-469-4663)
www.sears.com
To bring in products such as vacuums, lawn equipment and electronics
for repair, call for the location of your nearest Sears Parts & Repair Center.
1-800-488-1222
Anytime, day or night
www.sears.com
For the replacement parts, accessories and owner’s manuals
that you need to do-it-yourself, call Sears PartsDirect SM !
1-800-366-PART
(1-800-366-7278)
6 a.m. – 11 p.m. CST,
7 days a week
www.sears.com/partsdirect
To purchase or inquire about a Sears Service Agreement:
1-800-827-6655
7 a.m. – 5 p.m. CST, Mon. – Sat.
Para pedir servicio de reparación a domicilio,
y para ordenar piezas con entrega a domicilio:
1-888-SU-HOGAR
Au Canada pour service en français:
1-877-LE-FOYER SM
SM
(1-877-533-6937)
(1-888-784-6427)
SM
HomeCentral
® Registered Trademark / ™ Trademark of Sears, Roebuck and Co.
© Sears, Roebuck and Co.
® Marca Registrada / ™ Marca de Fábrica de Sears, Roebuck and Co.