Electrolux EKC6046 Specifications

Model EKC6046 /EKC6047
IMPORTANT SAFETY INFORMATION
Always support the grill pan when it is in the
withdrawn or partially withdrawn position.
Always use oven gloves to remove and replace the
grill pan handle when grilling.
Always use oven gloves to remove and place food in
the oven.
Ensure cooking utensils are large enough to contain
foods to prevent spillage and boil over.
The handles of saucepans, which are smaller than
the heated area on the hob, will become hot.
Ensure your hand is protected before handling the
pan.
Do not use the appliance if the ceramic glass is
damaged. If a fault or crack becomes visible,
disconnect the appliance immediately from the
electricity supply and contact your local service force
centre.
During use the appliance becomes hot. Care should
be taken to avoid touching heating elements inside
the oven.
Ensure that all vents are not obstructed to ensure
ventilation of the oven cavity.
Never line any part of the appliance with foil.
Always stand back from the appliance when opening
the doors to allow any build up of steam or heat to
release.
Never leave the appliance unattended when the
oven door is open.
Do not place sealed cans or aerosols inside the
oven. They may explode if they are heated.
Ensure that all control knobs are in the OFF position
when not in use.
Do not stand on the appliance or on the open oven
doors.
Do not hang towels, dishcloths or clothes from the
appliance or its handles.
Do not use this appliance if it is in contact with water.
Never operate it with wet hands.
These warnings are provided in the interests of your
safety. Ensure that you understand them all before
installing or using the appliance. Your safety is of
paramount importance. If you are unsure about any
of the meanings of these warnings contact the
Customer Care Department.
INSTALLATION
The appliance must be installed according to the
instructions supplied. The installation work must be
undertaken by a qualified electrician or competent
person.
The appliance should be serviced by an authorised
Service Engineer and only genuine approved spare
parts should be used.
The appliance must be installed in an adequately
ventilated room.
If the appliance is to be placed on a base, measures
must be taken to prevent the appliance from slipping.
This appliance is heavy and care must be taken
when moving it.
Do not attempt to lift or move this appliance by the
handles.
All packaging, both inside and outside the appliance
must be removed before the appliance is used.
It is dangerous to alter the specifications or modify
the appliance in any way.
After installation please dispose of the packaging
with due regard for safety and the environment. Your
local authority can arrange this.
CHILD SAFETY
Do not allow children to play with any part of the
packaging.
Do not allow children to sit or climb on the drop down
doors.
This appliance is designed to be operated by adults.
Young children must not be allowed to tamper with
the controls or play near or with the appliance.
CAUTION: Accessible parts may be hot when the
grill is in use. Young children should be kept
away.
CLEANING AND MAINTENANCE
For hygiene and safety reasons this appliance
should be kept clean at all times. A build-up of
fats or other foodstuffs could result in a fire
especially in the grill pan.
Do not leave the cookware containing foodstuffs,
e.g. fat or oil in the appliance in case it is
inadvertently switched on.
Extreme care must be taken when using a ceramic
hob scraper.
Always allow the appliance to cool before switching
off at the wall prior to carrying out any cleaning /
maintenan0ce work.
Only clean this appliance in accordance with the
instructions given in this book.
Never use steam or high pressure steam cleaners to
clean the appliance.
DURING USE
This appliance is not intended to be operated by
means of an external timer or separate remote
control system.
This appliance has been designed for domestic use
to cook edible foodstuffs only and must not be used
for any other purposes.
Take great care when heating fats and oils as they
will ignite if they become too hot.
Never place plastic or any other material which may
melt in or on the oven.
Do not leave the grill pan handle in position when
grilling as it will become hot.
2
CONTENTS
FOR THE USER
Important Safety Information
Description of the Appliance
Getting to Know Your Appliance
Before Using the Appliance
Rating Plate
Preparing to Use your Appliance
The Cooling Fan for the Controls
Control Panel Indicator Neon(s)
Condensation and Steam
Cookware
Grill and Oven Furniture
2
4
5
6
6
6
6
6
6
6
6
The Timer
7
Cleaning the Outside of the Appliance
Cleaning the Control Knobs and Handles
Removing And Replacing Wirework Runners
Cleaning the Ceramic Hob
Hints and Tips
Cleaning the Shelves, Wirework Runners
and Grill/Oven Furniture
Cleaning Inside the Grill and Oven
Compartments
Hints and Tips
Cleaning the Door(s)
Replacing An Oven Light Bulb
21
21
21
22
23
24
24
24
26
Something Not Working?
Service and Spare Parts
Guarantee Conditions
27
28
29
23
FOR THE INSTALLER
The Ceramic Hob
Using the Hob
Recommended Saucepans
Hints and Tips
10
10
10
11
The Grill
Using the Grill
Things to Note
The Grill Pan and Handle
Hints and Tips
Grilling Chart
12
12
12
12
12
13
The Top Oven
Using the Top Oven
Things to Note
To Fit the Top Oven Shelf
Hints and Tips
14
14
14
14
15
The Main Oven
Using the Main Oven
Things to Note
To Fit the Main Oven Shelves
Hints and Tips
16
16
16
16
17
Oven Cooking Chart
18
Roasting Chart
19
Defrost Feature
Using Defrost Feature
Things to Note
Hints and Tips
20
20
20
20
Care and Cleaning
Cleaning Materials
21
21
Technical Details
Installation Instructions
30
31
To help you the following symbols will be found
in the text.
Hints and Tips
Safety Instructions.
Please read the instruction book carefully
before use and retain for future reference.
AT THE END OF THE APPLIANCE'S LIFE
The symbol
on the product or on its packaging
indicates that this product may not be treated as
household waste. Instead it shall be handed over
to the applicable collection point for the recycling of
electrical and electronic equipment. By ensuring
this product is disposed of correctly, you will help
prevent potential negative consequences for the
environment and human health, which could
otherwise be caused by inappropriate waste
handling of this product.
For more detailed
information about recycling of this product, please
contact your local city office, your household waste
disposal service or the shop where you purchased
the product.
3
DESCRIPTION OF THE APPLIANCE
SLIP-IN ELECTRIC DOUBLE OVEN
Electronic Timer
Control Panel
Top Oven / Grill
Main Oven
4
GETTING TO KNOW YOUR APPLIANCE
THE CONTROL PANEL
E
D
G
F
J
FEATURES
-
Hotplate Control
Hotplate Control
Main Oven Temperature Control
Electronic Timer
Top Oven/Grill Selector Control
Top Oven/Grill Temperature Control
Hotplate Control
Hotplate Control
Main Oven Indicator Neon
Top Oven/Grill Indicator Neon
5
4
I
A
B
C
D
E
F
G
H
I
J
H
4
2
2
C
4
4
2
B
2
A
BEFORE USING THE APPLIANCE
RATING PLATE
For your safety wall coverings at the rear of the
appliance should be securely fixed to the wall.
This is situated on the lower front frame of the
appliance and can be seen upon opening the door.
Alternatively the rating plate may also be found on
the back or top of some models (where applicable).
The appliance must be protected by a suitably rated
fuse or circuit breaker. The rating of the appliance is
given on the rating plate.
Do not remove the rating plate from the appliance
as this may invalidate the guarantee.
COOKWARE
Baking trays, dishes etc., should not be placed
directly against the grid covering the fan at the back
of the oven.
Do not use baking trays larger than 30cm x 35cm
(12” x 14”) as they will restrict the circulation of heat
and may affect performance.
PREPARING TO USE YOUR APPLIANCE
GRILL AND OVEN FURNITURE
Wipe over the base of the oven(s) with a soft cloth
and hot soapy water and wash the furniture before
use. We suggest that you run the oven elements for
10 – 15 minutes at 220oC to burn off any residue
from their surfaces. The procedure should be
repeated with the grill for approximately 5 – 10
minutes. During this period an odour may be
emitted, it is therefore advisable to open a window for
ventilation.
The following items of grill and oven furniture have
been supplied with the appliance. If you require
replacements of any of the items listed below please
contact your local Service Force Centre, quoting the
relevant part number.
THE COOLING FAN FOR THE CONTROLS
1 grill pan
(349099801)
The cooling fan comes on immediately when the
grill/top oven is switched on and after a short time
when the main oven is in use. It may run on after the
controls are switched off until the appliance has
cooled. During the initial period the cooling fan may
turn ON and OFF, this is quite normal.
1 grill pan handle
(349100501)
Always allow the cooling fan to cool the
appliance down before switching off at the
wall prior to carrying out any cleaning or
maintenance work.
1 grill pan grid
(311757500)
CONTROL PANEL INDICATOR NEON(S)
The indicator neon will operate when the grill (where
applicable) or oven(s) is switched on. The indicator
neon will glow. It may turn on and off during use to
show that the setting is being maintained. If the neon
does not operate as the instructions indicate the
controls have been incorrectly set.
Return all
controls to zero and reset following the instructions
for the required setting.
1 cranked shelf
(for grilling and
top oven cooking)
CONDENSATION AND STEAM
When food is heated it produces steam similar to a
boiling kettle. The vents allow some of this steam to
escape. However, always stand back from the
appliance when opening the door(s) to allow any
build up of steam or heat to release.
If the steam comes into contact with a cool surface
on the outside of the appliance, e.g. a trim, it will
condense and produce water droplets. This is quite
normal and is not caused by a fault on the appliance.
To prevent discolouration, regularly wipe away
condensation and also soilage from surfaces.
2 cranked shelves
(for main oven
cooking)
6
THE TIMER
KEY
A
B
C
D
E
F
G
COOK TIME
END TIME
COUNTDOWN
TIME
DECREASE CONTROL
SELECTOR CONTROL
INCREASE CONTROL
A
C
B
D
E
NOTE:
The time of day must be set before the main oven
will operate manually.
1. HOW TO SET THE TIME OF DAY
The oven has a 24 hour clock.
When the electricity supply is first switched ON, the
display will show 12.00 and the 'Time' indicator neon
will flash as Fig. 1.
Fig.1.
To set the correct time press the increase control
button (+) and if necessary, the decrease control
button (-) until the correct time on the 24 hour clock is
reached, e.g. 10.00am as Fig. 2. The 'Time' indicator
neon will flash for 5 seconds and then go out.
NOTE:
The increase and decrease control
buttons operate slowly at first, and then more
rapidly. They should be pressed separately.
2. HOW TO SET THE COUNTDOWN
Fig.2.
The 'Countdown' gives an audible reminder at the
end of any period of cooking. This cooking period
may be up to 2 hrs 30 mins. It is not part of the
automatic control.
To set, press the Selector Control button until the
'Countdown' indicator neon is illuminated and the
display reads 0.00 as Fig. 3.
To set the correct time duration depress the increase
control (+) until the display indicates the interval to be
timed, e.g. 1hr 45 mins as Fig. 4. If necessary
depress the decrease control (-) to achieve the
correct time interval.
Fig.3.
NOTE: This must be completed within 5 seconds
of first pressing the Selector Control button.
During the operation of the 'Countdown', the
remaining time period will be shown in the display.
The 'Countdown' will sound intermittently for up to 2
minutes at the end of the timed period. The sound
can be stopped by pressing any button.
7
Fig.4.
F
G
TO CANCEL THE COUNTDOWN
If you change your mind and want to cancel the
'Countdown', press the Selector Control button until
the 'Countdown' indicator neon flashes then depress
the decrease control (-) until 0. 00 shows in the
display as Fig. 5. The 'Countdown' indicator neon
will continue to flash for a few seconds and then
return to the time of day.
3. SETTING THE OVEN TIMER CONTROL
Fig.5.
The main oven only can be automatically timed.
When using the timer control for the very first time, it
is advisable to let it operate while you are at home.
The displays can be checked to show that it is
operating correctly and you will feel confident to
leave a meal to cook automatically in the future.
A) TO SET THE TIMER TO SWITCH ON
AND OFF AUTOMATICALLY
i) Ensure the electricity supply is switched ON and
that the correct time of day is displayed, e.g.
9.a.m. as Fig. 6.
ii) Place food in oven.
iii) To set the length of cooking time. Press the
Selector Control button until the 'Cook Time'
indicator neon is illuminated. Press the increase
control (+) until the required length of cooking time
is displayed, e.g. 2 hrs 15 mins as Fig. 7. If
necessary depress the decrease control (-) until
the correct time interval is achieved.
The maximum cooking time is 10 hours.
iv) Release the buttons. The 'Cook Time' indicator
neon will be illuminated.
Fig.6.
Remember, this must be completed within 5
seconds of first pressing the Selector Control
button.
Fig.7.
v) To set the 'End Time'. Press the Selector Control
button until the 'End Time' indicator neon flashes.
Press the increase control button (+) until the
required stop time is displayed, e.g. 12.15 p.m. as
Fig. 8. If necessary depress the decrease control
(-) until the correct time interval is achieved.
vi) Release the buttons. The time of day will be
displayed after 5 seconds. The 'Cook Time' and
'End Time' indicator neons will be illuminated.
The 'End Time' must not be more than 23 hours
59 minutes from the time of day. For example, if
the time of day is 09.00 a.m., the latest 'End Time'
would be 08.59 a.m. the next day.
vii) Set the main oven control to the required
temperature. The oven indicator neon should be
OFF.
Fig.8.
NOTE: When the automatic timed period starts,
the oven indicator neon will turn ON and OFF
periodically during cooking, showing that the
temperature is being maintained.
8
B) TO SET THE TIMER TO SWITCH OFF
ONLY
i)
ii)
iii)
iv)
v)
vi)
Ensure the electricity supply is switched ON and
that the correct time of day is displayed, e.g.
10.00am as Fig. 9.
Place food in the oven.
To set the length of cooking time, press the
Selector Control button until the 'Cook Time'
indicator neon is illuminated. Press the increase
control ( + ) until the required length of cooking
time is displayed, e.g. 2 hrs 15 mins as Fig. 10.
Depress the decrease control ( - ) if necessary.
Release the buttons. The 'Cook Time' indicator
neon will illuminate and the time of day will be
displayed after 5 seconds.
Set the oven temperature. The oven indicator
neon should be ON.
To check the 'End Time' during the cooking
period, simply press the Selector Control button
once and the remaining time will be displayed, as
Fig. 11.
Fig.9.
4. TO CANCEL AN AUTOMATIC
PROGRAMME
Fig.10.
i)
To cancel an automatic programme press the
Selector Control button until the 'Cook Time'
indicator neon flashes. Press the decrease
control ( - ) until the display reads 0.00 as Fig.
12.
ii) Release the buttons. The 'Cook Time' indicator
neon will flash and after 5 seconds return to the
time of day.
iii) Turn off the oven controls.
5. TO RETURN THE APPLIANCE TO
MANUAL
Fig.11.
At the end of a timed cooking period, the
indicator neon will flash and an alarm will sound
for up to 2 minutes.
i) To stop the sound press any of the three buttons,
as Fig. 13.
ii) The display will return to the time of day.
iii) Turn off the oven controls.
6. THINGS TO NOTE
In the event of an interruption of the electricity
supply, the timer will reset itself to zero, and all
programming will be cancelled.
Fig.12.
7. AUTOMATIC COOKING
It is advisable to leave food in the oven for as
short a time as possible before automatic
cooking. Always ensure commercially prepared
food is well within its use by date and that home
prepared food is fresh and of good quality.
When cooking is complete, do not leave food to
stand in the oven, but remove and cool it quickly
if the food is not to be consumed immediately.
Always ensure food in the oven has been
covered before cooking if it is not possible to
remove food immediately after cooking.
Fig.13.
9
THE CERAMIC HOB
Do not use the appliance if the ceramic
glass is damaged.
If a fault or crack
becomes visible, disconnect the appliance
immediately from the electricity supply and
contact your local Service Force Centre.
USING THE HOB
The highest number represents the hottest
setting and the lowest number represents the
coolest setting. Choose a setting appropriate to
the quantity and type of food to be cooked.
RECOMMENDED SAUCEPANS
Only saucepans with flat bases and close fitting lids
are recommended. The saucepan base should be
approximately the same size as the cooking area.
Ensure that new saucepans are well scrubbed to
remove edges and take off any deposits left from
manufacture.
Traditional round bottomed Woks must not be used
even with a stand. Woks with flat-bottomed bases
are available and do comply with the above
recommendations.
NOTE:
Occasionally the heated areas may be seen to switch
ON and OFF when higher heat settings are being
used. This is due to a safety device which prevents
the glass from overheating.
Some switching ON and OFF when cooking at high
temperatures, e.g. deep fat frying is quite normal,
causes no damage to the hob and little delay in
cooking times.
Excessive switching may however be caused by the
use of an unsuitable saucepan or a saucepan which
is smaller than the heated area.
If excessive
switching occurs, discontinue use of the saucepan.
10
2
•
To operate the hotplates, turn the control knob in
either direction to vary the heat setting.
4
•
HINTS AND TIPS
•
•
•
•
•
•
•
Lift, rather than slide saucepans on and off the
hob. This will reduce the risk of scratches and
metal marks from saucepans with aluminium
bases. Metal marks can be easily cleaned off
providing they are not allowed to burn on.
Follow any guidelines provided by the saucepan
manufacturer, particularly those relating to
recommended heat settings.
Avoid using thin, badly dented or distorted
saucepans. Those with uneven bases should not
be used.
Never leave the hotplates ON when not covered
with a saucepan.
Ensure that the hob and saucepans are clean
and dry before the start of cooking.
Follow the cleaning instructions very closely to
keep the hob looking like new.
If spillage occurs with sugar solutions, e.g.
jams and syrups, it must be wiped from the
hob before it sets and becomes hard
otherwise damage to the hob will occur.
HOT HOB INDICATOR
The hob is fitted with a hot hob indicator light which
illuminates when the hob is too hot to touch. The
light will go OFF when the hob has cooled.
11
THE GRILL
CAUTION – Accessible parts may be hot
when the grill is in use. Young children
should be kept away.
USING THE GRILL
•
•
•
To operate the grill select the grill function for full
grill.
Turn the temperature control knob to the right as
far as it will go. This is the hottest setting.
To use the grill at lower settings, tun the
temperature control knob so that 110°C or 150°C
on the knob lines up with the off dot on the panel.
THINGS TO NOTE
•
•
•
The cooling fan for the controls may operate after
a time.
Some smoke from fat splashes may be evident
as the grill cleans itself.
The Top oven cannot be operated when the grill
is in use.
THE GRILL PAN AND HANDLE
The grill pan is supplied with a removable handle.
To attach the handle, press the button on the handle
with the thumb and insert the lip into the widest part
of the bracket. Slide the handle towards the left and
release the button.
Ensure the handle is correctly located.
To remove the handle, press the button on the
handle with the thumb and slide the handle towards
the right. Release the button.
Always remove the grill pan handle during
grilling.
Place the grill pan on the shelf so that the pan is
positioned centrally beneath the grill. Ensure that the
cut out on the underside of the handle bracket
locates between the bars of the shelf.
12
HINTS AND TIPS
•
•
•
•
•
•
•
Most foods should be placed on the grid in the
grill pan to allow maximum circulation of air to lift
the food out of the fats and juices.
Adjust the grid and grill pan runner position to
allow for different thicknesses of food. Position
the food close to the element for faster cooking
and further away for more gentle cooking.
Food should be thoroughly dried before grilling to
minimise splashing. Brush lean meats and fish
lightly with a little oil or melted butter to keep
them moist during cooking.
Accompaniments such as tomatoes and
mushrooms may be placed underneath the grid
when grilling meats.
GRILLING CHART
FOOD
When toasting bread, use the shelf in position 6
with the grid in the ‘high’ position.
POSITION
Bacon Rashers
Beefburgers
Preheat the grill on a full setting for a few minutes
before sealing steaks or toasting. Adjust the heat
setting and the shelf as necessary during
cooking.
Chicken Joints
Chops – Lamb
Pork
The food should be turned over during cooking
as required.
GRILL TIME
(mins in total)
5-6
Adjust
grill
setting
and
10 - 15
30 - 40
15 - 20
20 - 30
Fish – Whole
Trout/Mackerel
grill
Fillets Plaice/Cod
pan
10 - 15
Kebabs
grid
20 - 30
Kidneys –
Lamb/Pig
to
8 - 12
Liver –
Lamb/Pig
suit
15 - 25
10 - 20
different
Sausages
Steaks – Rare
Medium
Well Done
Toasted
Sandwiches
20 - 30
thicknesses
of
food
6 - 12
12 - 16
14 - 20
3-4
The times quoted above are given as a guide and
should be adjusted to suit personal taste.
13
THE TOP OVEN
The top oven is the smaller of the two ovens. It is
heated by elements in the top and bottom of the
oven. It is designed for cooking smaller quantities of
food. It gives especially good results if used to cook
fruit cakes, sweets and savoury flans or quiche.
The top oven is also ideal for use as warming
compartment to warm dishes and keep food hot.
Use the top oven when you want to warm plates.
Use the lowest setting on the top oven temperature
control.
USING THE TOP OVEN
•
•
Turn the top oven/grill selector to top oven.
Turn the top oven temperature control to the
required setting.
THINGS TO NOTE
•
•
•
•
The oven light will illuminate.
The indicator neon will glow. It may turn ON and
OFF during use to show that the setting is being
maintained.
The cooling fan for the controls may operate after
a time.
The grill cannot be operated when the top oven is
in use.
Do not place dishes, tins and trays directly on
the oven base as it becomes very hot and
damage will occur.
TO FIT THE TOP OVEN SHELF
The shelf should be fitted with the straight rods
uppermost on the frame and the forms towards the
back of the oven. To remove a shelf slide the shelf
towards you until the shelf stop is reached. Tilt shelf
up at the front to that the stops clear the side
supports. Lift shelf clear. To install a shelf, reverse
the above steps. Each shelf position has an upper
and lower support wire, ensure the shelf is placed
between these two support wires.
14
HINTS AND TIPS
•
•
•
•
•
•
•
•
Arrange the shelves in the required positions
before switching the oven ON. Shelf positions
are counted from the bottom upwards.
There should always be at least 2.5cm (1”)
between the top of the food and the element.
This gives best cooking results and allows room
for rise in yeast mixtures, Yorkshire puddings etc.
When cooking cakes, pastry, scones bread etc.,
place the tins or baking trays centrally on the
shelf.
Ensure that food is placed centrally on the shelf
and there is sufficient room around the baking
tray/dish to allow for maximum circulation.
Stand dishes on a suitably sized baking tray on
the shelf to prevent spillage onto the oven base
and to help reduce cleaning.
The material and finish of the baking tray and
dishes used affect base browning. Enamelware,
dark, heavy or non-stick utensils increase base
browning. Shiny aluminium or polished steel
trays reflect the heat away and give less base
browning.
Because of the smaller cooking space and lower
temperatures, shorter cooking times are
sometimes required. Be guided by the
recommendations given in the cooking chart.
Do not place baking trays directly on the oven
base as it interferes with the oven air circulation
and can lead to base burning; use the lower shelf
position.
For economy leave the door open for the shortest
possible time, particularly when placing food into
a pre-heated oven.
Do not place cookware and cooking pots
with rough bases e.g. cast iron on the oven
door as damage to the glass may occur.
15
THE MAIN OVEN
The fan oven is particularly suitable for cooking larger
quantities of food. The advantages of fan oven
cooking are:
PREHEATING
The fan oven quickly reaches its temperature, so it is
not usually necessary to preheat the oven. Without
preheating however, you may need to add an extra 5
– 10 minutes on the recommended cooking times.
For recipes needing high temperatures, e.g. bread,
pastries, scones, soufflés etc., best results are
achieved if the oven is preheated first. For best
results when cooking frozen or cooked chilled ready
meals always preheat the oven first.
COOKING TEMPERATURES
Fan oven cooking generally requires lower
temperatures than conventional cooking. Follow the
temperatures recommended in the cooking chart. As
a guide reduce temperatures by about 20°C – 25°C
for your own recipes, using a conventional oven.
BATCH BAKING
The fan oven cooks evenly on both shelf levels,
especially useful when batch baking.
USING THE MAIN OVEN
•
Turn the main oven temperature control to the
required setting.
THINGS TO NOTE
•
•
•
•
•
The oven light will illuminate.
The indicator neon will glow. It may turn ON and
OFF during use to show that the setting is being
maintained.
The cooling fan for the controls may operate after
a time.
The oven fan will operate.
If an automatic programme has been set, the
oven light will not come on until cooking begins.
TO FIT THE MAIN OVEN SHELVES
The shelf should be fitted with the straight rods
uppermost on the frame and the forms towards the
back of the oven. To remove a shelf slide the shelf
towards you until the shelf stop is reached. Tilt shelf
up at the front to that the stops clear the side
supports. Lift shelf clear. To install a shelf, reverse
the above steps. Each shelf position has an upper
and lower support wire, ensure the shelf is placed
between these two support wires.
16
HINTS AND TIPS
•
•
•
•
•
Arrange the shelves in the required positions
before switching the oven ON. Shelf positions
are counted from the bottom upwards.
When cooking more than one dish in the fan
oven, place dishes centrally on different shelves
rather than cluster several dishes on one shelf,
this will allow the heat to circulate freely for the
best cooking results.
When batch baking one type of food, e.g. Victoria
sandwich cakes, those of similar size will be
cooked in the same time.
It is recommended that when baking larger
quantities the shelf positions should be evenly
spaced to suit the load being cooked. A slight
increase in cooking time may be necessary.
Do not place baking trays directly on the oven
base as it interferes with the oven air circulation
and can lead to base burning; use the lower shelf
position.
Do not place cookware and cooking pots
with rough bases e.g. cast iron on the oven
door as damage to the glass may occur.
17
OVEN COOKING CHART
The oven temperatures are intended as a guide only. It may be necessary to increase or decrease the
temperatures by 10°C to suit individual preferences and requirements.
FAN OVEN
FOOD
Biscuits
Bread
Bread rolls/buns
Cakes:
SHELF
POSITION
Shelf
Small & Queen
Sponges
Victoria Sandwich
Madeira
Rich Fruit
Christmas
Gingerbread
Meringues
Flapjack
Shortbread
Casseroles:
Beef/Lamb
Chicken
Convenience Foods
Fish
Fish Pie (Potato Topped)
Fruit Pies, Crumbles
Milk Puddings
Pasta Lasagne etc.
Pastry:
Shortcrust
Choux
Eclairs, Profiteroles
Flaky/Puff Pies
Mince Pies
Meat Pies
Quiche, Tarts,
Flans
positions
are not
critical
but ensure
that oven
shelves
are
evenly
COOKING
TEMP °C
180 - 190
200 - 220
200 - 220
160 - 170
160 - 170
160 - 170
140 - 150
130 - 140
130 - 140
TOP OVEN
SHELF
POSITION
4
1
1
4
3
3
2
2
1
COOKING
TEMP°C
170 - 190
200 - 220
200 - 220
170 - 180
160 - 170
160 - 170
140 - 150
140 - 150
130 - 140
140 - 150
3
140 - 150
80 - 100
2
90 - 100
170 - 180
3
170 - 180
130 - 140
3
140 - 150
140 - 160
2
140 - 160
180 - 190
2
180 - 190
Follow manufacturer’s instructions
170 - 190
3
170 - 190
190 - 200
2
190 - 200
190 - 200
2
190 - 200
130 - 140
3
140 - 150
190 - 200
3
170 - 180
APPROX
COOK TIME (m)
10 - 20
25 - 30
15 - 20
18 - 25
18 - 20
18 - 25
1¼ - 1½h
2¼ - 2½h
3 - 4½h
depends on size
1¼ - 1½h
2½ - 3h
25 - 30
45 - 65
2½ - 3h
1¼ - 1½h
20 - 30
20 - 25
40 - 50
1½ - 2h
40 - 45
190 - 200
170 - 180
210 - 220
190 - 200
190 - 210
180 - 210
3
3
3
3
3
3
180 - 190
170 - 180
210 - 220
190 - 200
190 - 210
180 - 200
30 - 35
20 - 30
25 - 40
15 - 20
25 - 35
25 - 45
160 - 180
2
160 - 180
see roasting
chart
210 - 220
190 - 200
170 - 180
180 - 190
4
2
3
3
220 - 230
190 - 200
170 - 180
180 - 190
8 - 12
30 - 40
20 - 30
1 - 1½h
180 - 190
4
180 - 190
1 - 1½h
210 - 220
200 - 210
4
4
200 - 210
200 - 210
spaced
Roasting Meat, Poultry
Scones
Shepherd’s Pie
Soufflés
Vegetables:
when more
Baked Jacket
Potatoes
Roast Potatoes
Yorkshire Puddings: Large
Individual
than one is
used
Note: Shelf positions are counted from the bottom of the oven.
18
25 - 40
15 - 25
ROASTING CHART
INTERNAL TEMPERATURES –
Rare : 50-60°C; Medium : 60-70°C; Well done : 70-80°C
MEAT
TEMPERATURE
COOKING TIME
20-35 minutes per ½kg (1lb)
and 20-35 minutes over
Beef/ Beef boned
160-180°C
Mutton/Lamb
160-180°C
25-35 minutes per ½kg (1lb)
and 25-35 minutes over
Pork/Veal/Ham
160-180°C
30-40 minutes per ½kg (1lb)
and 30-40 minutes over
Chicken
160-180°C
15-20 minutes per ½kg (1lb)
and 20 minutes over
Turkey/Goose
160-180°C
15-20 minutes per ½kg (1lb)
up to 3½kg (7lb) then 10
minutes per ½kg (1lb) over
3½kg (7lb)
Duck
160-180°C
25-35 minutes per ½kg (1lb)
and 25-30 minutes over
Pheasant
160-180°C
35-40 minutes per ½kg (1lb)
and 35-40 minutes over
Rabbit
160-180°C
20 minutes per ½kg (1lb)
and 20 minutes over
The roasting temperatures and times given in the chart should be adequate for most joints, but slight adjustments
may be required to allow for personal requirements and the shape and texture of the meat. However, lower
temperatures and longer cooking times are recommended for less tender cuts or larger joints.
Wrap joints in foil if preferred, for extra browning uncover for the last 20 – 30 min. cooking time.
19
DEFROST FEATURE
This main oven function defrosts most foods faster
than more conventional methods. It is particularly
suitable for delicate frozen foods which are to be
served cold e.g. cream filled gateaux, cakes covered
with icings or frostings, cheesecakes, biscuits,
scones, etc.
USING DEFROST FEATURE
•
•
•
Turn the main oven temperature control to the
defrost setting.
When defrost is selected, the oven indicator neon
may come ON. It will stay ON until the oven
reaches room temperature and then go OFF.
It may turn ON and OFF periodically during
defrosting to maintain a steady room
temperature, inside the oven.
THINGS TO NOTE
•
The oven fan and interior light will come on.
HINTS AND TIPS
•
•
•
•
•
•
•
•
•
Place the frozen food in a single layer where
possible and turn it over half way through the
defrosting process.
The actual speed of defrosting is influenced by
room temperature. On warm days defrosting will
be faster than on cooler days.
It is preferable to thaw fish, meat and poultry
slowly in the fridge. However, this process can
be accelerated by using the defrost function.
Small or thin fish fillets, frozen peeled prawns,
cubed or minced meat, liver, thin chops, steaks
etc., can be thawed in 1 – 2 hours.
A 1kg/2¼lb oven ready chicken will be thawed in
approximately 5 hours. Remove the giblets as
soon as possible during the thawing process.
Joints of meat up to 2kg/4½lb in weight can be
thawed using the defrost function.
All joints of meat and poultry must be thawed
thoroughly before cooking.
Always cook
thawing.
thoroughly
immediately
after
Do not leave food at room temperature once it is
defrosted. Cook raw food immediately or store
cooked food in the fridge, once it has cooled.
Care must always be taken when handling foods
in the home. Always follow the basic rules of
food hygiene to prevent bacterial growth and
cross contamination when defrosting, preparing,
cooking, cooling and freezing foods.
20
CARE AND CLEANING
Before cleaning always allow the appliance to
cool down before switching off at the
electricity supply.
CLEANING MATERIALS
Before using any cleaning materials on your
appliance, check that they are suitable and that their
use is recommended by the manufacturer.
Cleaners that contain bleach should NOT be used as
they may dull the surface finishes. Harsh abrasives
and scourers should also be avoided. Multi-surface
anti-bacterial cleaning products should not be used
on the ceramic hob or on the surrounding trims.
CLEANING THE
APPLIANCE
OUTSIDE
OF
THE
Do not use abrasive cleaning materials e.g. Hob
Brite, Brillo pads or scourers on painted or printed
finishes as damage may occur. Regularly wipe over
the control panel, doors and appliance sides using a
soft cloth and hot soapy water. To prevent streaking
finish with a soft cloth.
Stainless Steel cream cleaners are abrasive and
should be avoided as they may dull the surface
finish. Any spillage on the stainless steel finish
must be wiped off immediately.
Do not attempt to remove any of the control
knobs from the appliance as this may cause
damage and is a safety hazard.
CLEANING THE CONTROL KNOBS AND
HANDLES
It is strongly recommended that only hot soapy water
is used for cleaning the control knobs and handles.
ANY OTHER CLEANING MATERIALS MAY DULL
THE SURFACE FINISH.
REMOVING AND REPLACING
WIREWORK RUNNERS
THE
1. Remove all shelves and furniture from the oven.
2. Hold the wirework at the bottom, unclip from the
cavity side and gently pull towards the centre of
the oven.
3. Unhook the runner at the top and remove from
the cavity.
4. To replace the runners, hook the wirework side
runner into the cavity, slide back and press into
place.
SIDE PANEL
CAVITY
CENTRE
Ensure the wirework runners are firmly in
position before replacing the oven
shelves.
21
CLEANING THE CERAMIC HOB
Make sure the ceramic glass is cool before cleaning.
It is important to clean the ceramic hob daily to
prevent soilage being burnt on.
Take care to avoid the hob trims when cleaning the
ceramic glass as they may be damaged by the
cleaning agents recommended.
DAILY CLEANING
Use the recommended Hob Brite Cleaner daily. If
soilage is not allowed to burn on it will be much
easier to clean off.
1. Apply a small amount of Hob Brite in the centre
of each area to be cleaned.
2. Dampen a clean paper towel or a plastic pad
made specially for non-stick saucepans and rub
vigorously until all marks are removed. This may
take a few minutes.
3. Wipe off residues of cleaner with another damp
paper towel and polish dry with a soft cloth.
If Hob Brite is unavailable, one or more of the
cleaning agents below may be used temporarily:
a) Cif Cream Cleaner
b) Baking Soda
TO REMOVE MORE STUBBORN MARKS
1. Bar Keepers Friend may be used to clean off
more
stubborn
stains
or
to
remove
discolourations.
It may be necessary to rub the marks hard for
several minutes.
2. Use a plastic pad specially for non-stick
saucepans with Bar-Keepers Friend for removal
of more stubborn soilage.
TO REMOVE BURNT ON SOILAGE
We strongly recommend the use of a Ceramic Hob
Scraper (incorporating a single edge razor blade) to
remove spillage on the hob, in particular sugar
solutions, which if not removed can cause permanent
damage.
1. Make sure the ceramic glass is cool.
2. Use a ceramic hob scraper with care at an angle
of 30° to remove as much soilage as possible.
3. Use Bar-Keepers Friend or Hob Brite to finish off
as directed above.
TO REMOVE DISCOLOURATIONS OR
WHITE AND SILVER MARKS
These marks sometimes give the impression of being
in or underneath the hob glass. They can almost
always be removed provided they have not become
excessively burnt on. Follow the instructions above
under ‘To Remove more Stubborn Marks’.
If this is unsuccessful, make up a paste of one part
water to three parts Cream of Tarter and leave on the
discoloured areas overnight. The marks should be
easily removable the next day provided they have not
been excessively burnt on. The paste should be
thoroughly washed off afterwards.
22
HINTS AND TIPS
TO REDUCE HOB SOILAGE:
•
•
•
•
•
Make sure the bottom of the saucepan and the
cooking area are clean and dry before cooking
begins.
Ensure saucepans are large enough
accommodate food to avoid boil overs.
If possible, wipe up spills and splatters as they
occur, but take care to avoid steam burns.
Avoid using a dishcloth or sponge to clean the
hob. These may leave a layer of soiled detergent
on the hob surface which will burn and discolour
the next time the hob is used.
Avoid the use of:
•
•
•
•
•
•
•
•
•
to
Household detergents and bleaches.
Impregnated plastic or nylon pads that are not
described as suitable for non-stick saucepans.
Brillo pads, Ajax pads, steel wool pads.
Chemical oven cleaners, e.g. aerosols and
oven pads.
Rust stain, bath and sink stain removers.
Any of the above products may cause
damage to the hob.
It is dangerous to mix different cleaning products.
The chemicals in them may react with each other
with hazardous results.
Soilage from sugar solutions must be
removed from the hob before the syrup has
set otherwise damage to the hob surface will
occur.
Avoid placing plastic items, foil or dishes on the
hot surface as this will cause damage to the hob.
CLEANING THE SHELVES, WIRE- WORK
RUNNERS AND GRILL/OVEN FURNITURE
All removable parts, except the grill pan handle can
be washed in the dishwasher.
The grill pan, grill pan grid, oven shelves and
wirework runners may be cleaned using a soap
impregnated steel wool pad. Soaking first in hot
soapy water will make cleaning easier.
23
CLEANING INSIDE THE
OVEN COMPARTMENTS
GRILL
AND
The sides and back of the grill/second oven and main
oven compartments are coated with a special
Stayclean coating. They should not be cleaned
manually.
The vitreous enamel main oven base and grill
compartment base can be cleaned using normal
oven cleaners with care. Ensure that the
manufacturers instructions are followed and that all
parts are well rinsed afterwards.
Aerosol cleaners must not come into
contact with elements, the door seal, or any
painted finishes as this may cause damage.
HINTS AND TIPS
Aerosol cleaners must not be used on
Stayclean surfaces.
Stayclean surfaces destroy splashes of food and fats
when the oven temperature is raised to around 220°C.
It is a good idea to run the oven for an hour or two per
week to ensure continued good performance from the
Stayclean finish.
Slight discolouration and polishing of the Stayclean
surfaces may occur in time. This DOES NOT affect
the Stayclean properties in any way.
Use minimal, if any, extra oil or fat when roasting
meat, potatoes only require brushing with fat before
cooking. Extra fat in the oven during roasting will
increase splashing and soilage.
It is NOT necessary to add water to a meat tin when
roasting. The water and the fat juices from the joint
create excessive splattering during cooking – even at
normal
temperatures,
as
well
as
causing
condensation.
Covering joints during cooking will also prevent
splashing onto the interior surfaces. Removing the
covering for the last 20-30 minutes will allow extra
browning if required. Some large joints and turkeys
especially benefit by this method of cooking, allowing
the joint to cook through before the outside is overbrowned.
24
CLEANING THE DOOR(S)
To prevent damaging or weakening the
door glass panels avoid the use of the
following:
•
Household detergents and bleaches
•
Impregnated pads unsuitable for nonstick saucepans
•
Brillo/Ajax pads or steel wool pads
•
Chemical oven pads or aerosols
•
Rust removers
•
Bath/Sink stain removers
Please note that the door
glass on your product
may differ in type and
shape from that shown in
the diagram.
CLEANING BETWEEN THE OUTER AND
INNER DOOR GLASS
The outer door glass is removable for cleaning.
TO REMOVE THE OUTER GLASS
Open the oven door to gain access to the top of the
oven door.
To remove the top trim:Top Oven - Carefully pull the trim away from the door
and lift off.
Main Oven - Carefully push the trim towards the
oven. Remove the seal.
Hold the door glass securely in place with one hand
before sliding the glass out with the other hand.
Clean the outer and inner glass using hot soapy
water or Hob Brite cleaner may be used. Do not
use Hob Brite on the Stainless Steel or painted
finishes. Ensure that all parts are well rinsed and
thoroughly dried before attempting to replace the
outer door.
If the door glass panel becomes chipped or
has deep scratches the glass will be
weakened and must be replaced to prevent
the possibility of the panel shattering.
Please contact your local Service Force
Centre who will be pleased to advise
further.
TO REPLACE THE OUTER GLASS
To ensure the glass is properly located the text 'This
side up' should be facing towards you at the top edge
of the door and facing into the cavity.
Holding the glass with both hands, gently slide the
glass into the side trims of the oven door. Always
ensure that the glass is returned to the same side
trim it was removed from.
Replace the seal on the main oven door if removed.
To replace the trim, line up the clips on the underside
of the trim with the connectors at the top of the door.
Carefully slide the trim towards the door.
Ensure the trim is securely in place before closing the
oven door.
Do not attempt to use the oven without the
glass being in place.
25
REPLACING AN OVEN LIGHT BULB
The type of bulb required is a 300°C 25 watt small
Edison Screw.
Disconnect the appliance from the
electricity supply before replacing the bulb.
1. Make sure the appliance is cool before replacing
the bulb.
2. Open the door and remove the shelves and
wirework runners.
3. Remove the glass cover by turning it to the left.
4. Unscrew the bulb by turning it to the left.
5. Fit a new bulb and then replace the glass bulb
cover.
6. Refit the wirework runners and replace the oven
shelves.
7. Restore the electricity supply and reset the time of
day.
26
SOMETHING NOT WORKING?
Please carry out the following checks on your appliance before calling a Service Engineer. It may be that the
problem is a simple one which you can solve yourself without the expense of a service call.
In-guarantee customers should make sure that the checks have been made as the engineer will make a
charge if the fault is not a mechanical or electrical breakdown.
Please note that proof of purchase is required for in-guarantee service calls.
PROBLEM
POSSIBLE SOLUTION
The grill, ovens and timer do not work.
Check that the appliance has been wired in to the
appliance supply and is switched on at the wall.
Check that the main appliance fuse is working.
If you have checked the above:
Allow the appliance to cool for a couple of hours. The
appliance should now be working normally.
The grill and top oven work but the main oven does
not.
Check that the time of day has been set on the clock.
Check that the oven is set for manual cooking.
The grill does not work or cuts out after being used
for a long period of time.
Ensure the cooling fan is running when the grill is on. If
the cooling fan fails, the grill will not operate correctly.
Contact your local Service Force Centre.
Leave the grill door open and allow the grill to cool. After
a couple of hours check that the grill works as normal
The timer does not work.
Check that the instructions for the operation of the timer
are being closely followed.
The indicator neons are not working correctly.
Check that you have selected only the function you
require. Ensure all other controls are in the Off position.
The oven is not cooking evenly.
Check that the appliance is correctly installed and is
level.
Check that the recommended temperatures and shelf
positions are being used.
The oven light fails to illuminate.
The oven light bulb may need replacing.
If the Main Oven is set for automatic cooking the light will
illuminate when the cook time begins.
The oven fan is noisy.
Check that the oven is level.
Check that the shelves and bakeware are not vibrating in
contact with the oven back panel.
The oven temperature is too high or too low.
Check that the recommended temperatures and shelf
positions are being used. Be prepared to adjust the
temperature up or down by 10°C to achieve the results
you want.
27
SERVICE AND SPARE PARTS
In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local
Service Force Centre by telephoning:-
0870 5 929929
Your telephone call will be automatically routed to the Service Force Centre covering your post code area.
For the address of your local Service Force Centre and further information about Service Force, please visit the
website at www.serviceforce.co.uk.
Before calling out an engineer, please ensure you have read the details under the heading "Something Not
Working?".
When you contact the Service Force Centre you will need to give the following details:
1. Your name, address and post code.
2. Your telephone number.
3. Clear and concise details of the fault.
4. The model and serial number of the appliance (found on the rating plate).
5. The purchase date.
Please note that a valid purchase receipt or guarantee documentation is required for in-guarantee service
calls.
For Customer Service in Ireland please contact us at the address below:
Electrolux Group (Irl) Ltd
Long Mile Road
Dublin 12
Republic of Ireland
Tel: +353 (0) 1 4090753
Email: service.eid@electrolux.ie
CUSTOMER CARE DEPARTMENT
For general enquires concerning your Electrolux appliance or for further information on Electrolux products, please
contact our Customer Care Department by letter or telephone at the address below or visit our website at
www.electrolux.co.uk
Customer Care Department
Electrolux
Major Appliances
Addington Way
Luton
Bedfordshire
LU4 9QQ
Tel: 0870 5 950950 (*)
*calls to this number may be recorded for training purposes.
28
GUARANTEE CONDITIONS
Standard guarantee conditions
We, Electrolux, undertake that if within 12 months of the date of the purchase this Electrolux appliance or any
part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option
repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that:
•
•
•
•
•
•
The appliance has been correctly installed and used only on the electricity supply stated on the rating
plate.
The appliance has been used for normal domestic purposes only, and in accordance with the
manufacturer’s instructions.
The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person
not authorised by us.
All service work under this guarantee must be undertaken by a Service Force Centre.
Any appliance or defective part replaced shall become the Company’s property.
This guarantee is in addition to your statutory and other legal rights.
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these
hours in which case a premium will be charged.
Exclusions
This guarantee does not cover:
•
•
•
•
Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs
or removable parts of glass or plastic.
Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances
outside the United Kingdom.
Appliances found to be in use within a commercial environment, plus those which are subject to rental
agreements.
Products of Electrolux manufacture which are not marketed by Electrolux.
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new home
subject to the following qualifications:
•
•
•
•
•
•
The guarantee starts from the date you first purchased your product.
The guarantee is for the same period and to the same extent for labour and parts as exists in the new
country of use for this brand or range of products.
This guarantee relates to you and cannot be transferred to another user.
Your new home is within the European Community (EC) or European Free Trade Area.
The product is installed and used in accordance with our instructions and is only used domestically, i.e. a
normal household.
The product is installed taking into account regulations in your new country.
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your
new home. They will then ensure that the local Service Organisation is aware of your move and able to look
after you and your appliances.
France
Germany
Italy
Sweden
UK
Ireland
Senlis
Nürnberg
Pordernone
Stockholm
Luton
Dublin
+33 (0) 3 44 62 20 13
+49 (0) 800 234 7378
+39 (0) 800117511
+46 (0) 20 78 77 50
+44 (0) 8705 950 950
+353 (0) 1 4090753
29
TECHNICAL DETAILS
Voltage:
230-240 Volts AC 50Hz
Wattage:
9.5 - 10.3 kW
Height:
900mm
Width:
600mm
Depth:
600mm
(excluding handles and knobs)
Weight
68.0kg
This appliance complies with: European Council Directive 73/23/EEC.
EMC Directive 89/336/EEC.
CE Marking Directive 93/68/EEC. Energy Label Directive 2002/40/EC.
30
INSTALLATION INSTRUCTIONS
WARNING: THIS APPLIANCE MUST BE
EARTHED
If your appliance has been damaged in transit,
contact your supplier immediately. Do not attempt to
install it.
Your appliance left the factory fully packaged to
protect it from damage. If it is delivered without
packaging and damage has occurred, the
manufacturer cannot accept responsibility. Contact
your supplier for advice.
Once the packaging has been removed the appliance
should only be moved by hand. Do not use a sack
barrow or any other aid to lift the appliance as
damage may occur.
Connection to the electricity supply must be carried
out by a qualified electrician/competent person.
Fig.1.
The electrical connection should be made using a
double pole isolating switch (cooker socket) with at
least 3mm contact separation in all poles. The cable
must have conductors of sufficiently high crosssectional area to prevent overheating and
deterioration.
The recommended cross-section area is six square
millimetres (6.00mm2).
When refitting the mains terminal cover, ensure that
the lower tabs are located inside the bottom edge of
the aperture, before fixing the two screws into the top
edge of the mains terminal cover. See Fig.1. Ensure
that the cover is securely fastened.
To move the appliance, open the oven door, and lift
the appliance by holding inside the top of the
compartment. See Fig.2.
Fig.2.
This is a type Y appliance, which means it is freestanding and can be fitted with cabinets on one or
both sides. It may also be fitted in a corner setting.
Side walls which are above hob level should be
protected by heat resistant non-combustible material
and MUST NOT be nearer than 40mm to the hob
side.
Air gap
A nominal air gap of 2mm at either side of the
appliance is required to enable the appliance to be
moved into position.
Fig.3.
Always ensure an air gap is maintained at hotplate
level. Tiles or other forms of deep wall covering
should not obscure this gap. See Fig.3.
Overhanging surfaces or a cooker hood should be a
minimum of 685mm above the hob. See Fig.4.
It is important to ensure that the appliance is level
after installation. Levelling feet are fitted to the
appliance to accommodate uneven floors.
Fig.4.
31
IMPORTANT NOTICE
In line with our continuing policy of research and development, we reserve the right to alter models and
specifications without prior notice.
This instruction booklet is accurate at the date of printing, but will be superseded if specifications or appearance are
changed.
ELECTROLUX
MAJOR APPLIANCES,
ADDINGTON WAY,
LUTON,
BEDFORDSHIRE
LU4 9QQ.
TELEPHONE 0870 5 950950
To buy accessories, consumables and spare parts at our online shop please visit:
http://www.electrolux.co.uk
Part Number: 349095801
© Electrolux plc 2005