Bryant 330JAV Instruction manual

Add to my manuals
12 Pages

advertisement

Bryant 330JAV Instruction manual | Manualzz

service and maintenance procedures

PLUS 80 2-STAGE GAS-FIRED

INDUCED-COMBUSTION FURNACES

Cancels: SP04-65

330JAV

331JAV

Series D

SP04-73

11-01

NOTE: Read the entire instruction manual before starting the installation.

This symbol

→ indicates a change since the last issue.

TABLE OF CONTENTS

SAFETY CONSIDERATIONS .....................................................1

INTRODUCTION ..........................................................................2

ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS

PROCEDURE ................................................................................2

CARE AND MAINTENANCE.....................................................2

Cleaning and/or Replacing Air Filter.......................................2

Blower Motor and Wheel.........................................................3

Cleaning Heat Exchanger .........................................................4

Electrical Controls and Wiring.................................................6

WIRING DIAGRAMS...................................................................7

TROUBLESHOOTING .................................................................7

EFFICIENCY

RATING

CERTIFIED

A94086

C ar rie r Corporat io n

R

E

G

I

S

O

IST ®

ERED F

9001

#A2

8

I

8

R

3

M

REGISTERED QUALITY SYSTEM

CERTIFIED

Fig. 2—Model 331JAV Downflow

A95137

Fig. 1—Model 330JAV Horizontal

SAFETY CONSIDERATIONS

Installing and servicing heating equipment can be hazardous due to gas and electrical components. Only trained and qualified personnel should install, repair, or service heating equipment.

Untrained personnel can perform basic maintenance functions such as cleaning and replacing air filters. All other operations must be performed by trained service personnel. When working on heating equipment, observe precautions in the literature, tags, and labels attached to or shipped with the unit and other safety precautions that may apply.

—1—

A94085

Fig. 3—Model 330JAV Upflow

Follow all safety codes. In the United States, follow all safety codes including the National Fuel Gas Code (NFGC) NFPA No.

54-1999/ANSI Z223.1-1999. In Canada, refer to the current edition of the National Standard of Canada CAN/CGA-B149.1and .2-M00 Natural Gas and Propane Gas Installation Codes

(NSCNGPIC) and Amendment No. 1. Wear safety glasses and work gloves. Have fire extinguisher available during start-up and adjustment procedures and service calls.

Recognize safety information. This is the safety-alert symbol .

When you see this symbol on the furnace and in instructions or manuals, be alert to the potential for personal injury.

Understand the signal words DANGER, WARNING, CAUTION, and NOTE. These words are used with the safety-alert symbol.

DANGER identifies the most serious hazards which will result in severe personal injury or death. WARNING signifies hazards which could result in personal injury or death. CAUTION is used to identify unsafe practices which would result in minor personal injury or product and property damage. NOTE is used to highlight suggestions which will result in enhanced installation, reliability, or operation.

WARNING: The ability to properly perform maintenance on this equipment requires certain expertise, mechanical skills, tools, and equipment. If you do not possess these, do not attempt to perform any maintenance on this equipment other than those procedures recommended in the User’s Manual. A FAILURE TO FOL-

LOW THIS WARNING COULD RESULT IN POS-

SIBLE DAMAGE TO THIS EQUIPMENT, SERIOUS

PERSONAL INJURY, OR DEATH.

7. An ESD service kit (available from commercial sources) may also be used to prevent ESD damage.

CARE AND MAINTENANCE

For continuing high performance and to minimize possible equipment failure, it is essential that periodic maintenance be performed on this equipment. Consult your local dealer as to proper frequency of maintenance and availability of a maintenance contract.

WARNING: Never store anything on, near, or in contact with furnace, such as:

1. Spray or aerosol cans, rags, brooms, dust mops, vacuum cleaners, or other cleaning tools.

2. Soap powders, bleaches, waxes or other cleaning compounds, plastic or plastic containers, gasoline, kerosene, cigarette lighter fluid, dry cleaning fluids, or other volatile fluids.

3. Paint thinners and other painting compounds, paper bags or other paper products.

A failure to follow this warning could result in corrosion of the heat exchanger, fire, personal injury, or death.

INTRODUCTION

These procedures are for size 60,000 through 120,000 Btuh units.

ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS

PROCEDURE

CAUTION: Electrostatic discharge can affect electronic components. Take precautions during furnace installation and servicing to protect the furnace electronic control.

Precautions will prevent electrostatic discharges from personnel and hand tools which are held during the procedure. These precautions will help to avoid exposing the control to electrostatic discharge by putting the furnace, the control, and the person at the same electrostatic potential.

1. Disconnect all power to the furnace. DO NOT TOUCH

THE CONTROL OR ANY WIRE CONNECTED TO THE

CONTROL PRIOR TO DISCHARGING YOUR BODY’S

ELECTROSTATIC CHARGE TO GROUND.

2. Firmly touch a clean, unpainted, metal surface of the furnace chassis which is close to the control. Tools held in a person’s hand during grounding will be satisfactorily discharged.

3. After touching the chassis you may proceed to service the control or connecting wires as long as you do nothing that recharges your body with static electricity (for example; DO

NOT move or shuffle your feet, DO NOT touch ungrounded objects, etc.).

4. If you touch ungrounded objects (recharge your body with static electricity), firmly touch furnace again before touching control or wires.

5. Use this procedure for installed and uninstalled (ungrounded) furnaces.

6. Before removing a new control from its container, discharge your body’s electrostatic charge to ground to protect the control from damage. If the control is to be installed in a furnace, follow items 1. through 5. before bringing the control or yourself into contact with the furnace. Put all used AND new controls into containers before touching ungrounded objects.

—2—

WARNING: Turn off gas and electrical supplies to unit before performing any maintenance or service on it.

Follow operating instructions on label attached to furnace. A failure to follow this warning could result in personal injury.

The minimum maintenance that should be performed on this equipment is as follows:

1. Check and clean air filter each month or more frequently if required. Replace if torn.

2. Check blower motor and wheel for cleanliness each heating and cooling season. Clean as necessary.

3. Check electrical connections for tightness and controls for proper operation each heating season. Service as necessary.

CAUTION: As with any mechanical equipment, personal injury can result from sharp metal edges, etc.; therefore, be careful when removing parts.

I.

CLEANING AND/OR REPLACING AIR FILTER

The air filter arrangement may vary depending on the application.

NOTE: If the filter has an airflow direction arrow, the arrow must point toward the blower.

WARNING: Never operate unit without a filter or with filter access door removed. A failure to follow this warning could result in fire, personal injury, or death.

To clean or replace filters, proceed as follows:

1. Downflow—filters installed in return-air duct. (see Fig. 4.) a. Turn off electrical supply before removing blower access door.

b. Remove blower access door.

c. Reach up behind top plate, tilt filters toward center of return-air plenum, remove filters. Replace filters if torn or damaged..

d. Furnaces are equipped with permanent, washable filters.

e. Clean filters by spraying tap water through filter from opposite direction of airflow.

INSTALLATION

POSITION

OF FILTERS

RETURN-AIR

PLENUM

AIRFLOW

;;;;

;;;; ;;;;

;;;; ;;;;

;;;; ;;;;

;;;; ;;;;

MOUNTING

SCREWS

RELIEF

BOX

GAS

VALVE

CONTROL

FLUE

COLLAR

BLOCKED

VENT

SAFEGUARD

PRESSURE

SWITCH

FLUE

COLLECTOR

BOX

ACCESS DOOR

A88486

Fig. 4—Downflow Filter Arrangement f. Rinse and let dry. Oiling or coating of filters is not recommended or required.

g. Reinstall filters.

h. Replace blower access door and turn on electrical supply to furnace.

2. Upflow/Horizontal–filters installed in media cabinet adjacent to furnace (See Fig. 5.) a. Turn off electrical supply to furnace b. Remove filter cabinet door.

c. Slide filter out of cabinet.

d. If equipped with permanent, washable filter, clean filter by spraying cold tap water through filter in opposite direction of airflow. Rinse filter and let dry. Oiling or coating of the filter is not recommended.

e. If equipped with factory-specified disposable media filter, replace only with media filter having the same part number and size.

f. Slide filter into cabinet.

g. Replace filter cabinet door.

h. Turn on electrical supply to furnace.

3. Upflow/Horizontal–filter(s) installed in side(s) and/or bottom of blower compartment (See Fig. 5.) a. Turn off electrical supply before removing blower and control access doors.

b. Release filter retainer from clip at front of furnace casing. (See Fig. 5.) For side return, clips may be used on either or both sides of the furnace.

c. Slide filter out.

d. Clean filters by spraying tap water through filter from opposite direction of airflow.

—3—

HUM HUM

FILTER

RETAINER

WASHABLE

FILTER

FURNACE

WASHABLE

FILTER OR

DISPOSIBLE

MEDIA FILTER

IN FILTER

CABINET

A00293

Fig. 5—Model 330JAV Upflow e. Rinse and let dry. Oiling or coating of filter is not recommended or required.

f. Place filter in furnace.

g. Replace blower and control access doors and turn on electrical supply to furnace.

II.

BLOWER MOTOR AND WHEEL

The following items should be performed by a qualified service technician:

For long life, economy, and high efficiency, clean accumulated dirt and grease from blower wheel and motor annually.

The inducer and blower motors are pre-lubricated and require no additional lubrication. These motors can be identified by the absence of oil ports on each end of the motor.

Clean blower motor and wheel as follows:

1. Turn off electrical supply to furnace.

2. Remove blower access door.

3. Downflow only: a. Disconnect vent connector from furnace flue collar. (See

Fig. 6.) b. Remove internal vent pipe enclosure cover.

c. Disconnect and remove short piece of vent pipe from within furnace.

d. Disconnect and remove vent pipe enclosure. Push bottom side backward to release tabs.

NOTE: Vent pipe is SCREWED and RTV sealed to relief box.

4. Disconnect blower leads from furnace control. Note wire color and location for reassembly. Also, disconnect auxiliary limit switch leads (downflow only, if present).

All other factory wires can be left connected, but field thermostat connections may need to be disconnected depending on their length and routing.

5. Remove 2 screws securing control and transformer support to furnace.

6. Hang control and transformer support to front of furnace casing.

AUXILIARY

LIMIT

SWITCH

MOUNTING

SCREWS

FLUE

COLLAR

VENT PIPE

ENCLOSURE

CONTROL

NOTE: Refer to Table 1 for motor speed lead relocation if leads were not identified before disconnection.

TABLE 1—SPEED SELECTOR

COLOR

Black

Yellow (When Present)

Blue

Red

White

Orange (When Present)

SPEED

High

Medium High

Medium Low

Low

Common

Medium

FACTORY-

ATTACHED

TO

Cool

Spare

Heat

Spare

C

OM

Spare

DRAFT

SAFEGUARD

SWITCH

PRESSURE

SWITCHES

CAUTION: Heating speed selection MUST be adjusted to provide proper temperature rise as specified on the rating plate. Failure to adjust the heating speed may shorten heat exchanger life.

RELIEF

BOX

MANUAL

RESET

LIMIT

SWITCHES

A99092

Fig. 6—Model 331JAV Downflow

7. Remove screws holding blower assembly to blower deck and slide blower assembly out of furnace.

8. Clean blower wheel and motor using a vacuum with soft brush attachment. Do not remove or disturb balance weights

(clips) on blower wheel blades. The blower wheel should not be dropped or bent as balance will be affected.

9. If greasy residue is present on blower wheel, remove wheel from the blower housing and wash it with an appropriate degreaser. To remove wheel: a. Mark blower wheel location on shaft before disassembly to ensure proper reassembly.

b. Loosen setscrew holding blower wheel on motor shaft.

NOTE: Mark blower mounting arms, motor, and blower housing so motor and each arm is positioned at the same location during reassembly.

c. Mark blower wheel orientation and cutoff plate location to ensure proper reassembly.

d. Remove screws securing cutoff plate and remove cutoff plate from housing.

e. Remove bolts holding motor mounts to blower housing and slide motor and mounts out of housing. Disconnect capacitor and ground wire attached to blower housing before removing motor.

f. Remove blower wheel from housing.

10. Reassemble motor and blower by reversing items 9a through 9f. Be sure to reattach ground wire.

11. Reinstall blower assembly in furnace.

12. Reinstall control box and support assembly in furnace.

13. Reconnect blower leads to furnace control and auxiliary limit switch leads (downflow only).

Refer to furnace wiring diagram, and connect thermostat leads if previously disconnected. (See Fig. 11.)

—4—

14. Reinstall internal vent pipe and enclosure on downflow

furnaces only by reversing items 3a through 3c.

NOTE: A releasing agent such as PAM cooking spray or equivalent (must not contain corn or canola oil, aromatic or halogenated hydrocarbons or inadequate seal may occur) and RTV sealant

(G.E. 162, 6702, or Dow-Corning 738) are needed before starting installation. DO NOT substitute any other type of RTV sealant.

G.E. 162 (P771-9003) is available through RCD in 3-oz tubes.

15. Reinstall vent connector to furnace flue collar. After fully assembling vent connector to furnace flue collar, securely fasten vent connector to flue collar with 2 field-supplied, corrosion-resistant, sheet metal screws located 180 degrees apart and midway up the collar.

16. Turn on electrical supply. Manually close blower access door switch. Use a piece of tape to hold switch closed.

Check for proper rotation and speed changes between heating and cooling by jumpering R to W and then R to Y on furnace control thermostat terminals.

WARNING: Blower access door switch opens 115-v power to furnace control. No component operation can occur. Caution must be taken when manually closing this switch for service purposes. Failure to follow this warning could result in electrical shock, personal injury, or death.

NOTE: If thermostat terminals are jumpered before blower access door switch is closed, blower will run for 90 sec before beginning a heating or cooling cycle.

17. If furnace is operating properly, remove tape to release blower access door switch, replace blower access door.

III.

CLEANING HEAT EXCHANGER

The following steps should be performed by a qualified service technician:

NOTE: If the heat exchangers get a heavy accumulation of soot and carbon, they should be replaced rather than trying to clean them thoroughly due to their intricate design. A build-up of soot and carbon indicates that a problem exists which needs to be corrected, such as improper adjustment of manifold pressure, insufficient or poor quality combustion air, incorrect size, or damaged manifold orifice(s), improper gas, or a restricted heat exchanger. Action must be taken to correct the problem.

If it becomes necessary to clean heat exchanger because of light dust or corrosion proceed as follows:

1. Turn gas and power to furnace to OFF.

2. Remove control and blower access doors.

3. Disconnect vent connector from furnace flue collar.

4. Disconnect internal vent pipe and enclosure on downflow

furnaces only.

a. Remove vent pipe enclosure cover.

b. Disconnect and remove short piece of vent pipe from within furnace.

NOTE: Vent pipe is SCREWED and RTV sealed to relief box.

c. Remove vent pipe enclosure by removing screw in upper back. Push bottom side backward to release tabs.

5. Remove 2 screws that secure relief box. (See Fig. 5 or 6.)

6. Disconnect wires to the following components. Mark wires to aid in reconnection of: a. Draft safeguard switch.

b. Inducer motor.

c. Pressure switch(es).

d. Limit overtemperature switch(es).

e. Gas valve.

f. Hot surface ignitor.

g. Flame-sensing electrode.

h. Flame rollout switch(es), if applicable.

7. Remove complete inducer assembly and relief box from furnace.

8. Remove screws that secure flue collector box to center panel. Be careful not to damage collector box.

9. Remove cell outlet plates.

IMPORTANT: Replace screws in center panel before cleaning.

10. Remove burner assembly and cell inlet plates.

IMPORTANT: Replace screws in center panel before cleaning.

NOTE: Be very careful when removing burner assembly to avoid breaking ignitor. See Fig. 7 for correct ignitor location.

11. Using field-provided small wire brush, steel spring cable, reversible electric drill, and vacuum cleaner, clean cells as follows: a. Assemble wire brush and steel spring cable.

(1.) Use 48 in. of 1/4-in. diameter high-grade steel spring cable (commonly known as drain clean-out or Roto-Rooter® cable).

(2.) Use 1/4-in. diameter wire brush (commonly known as 25-caliber rifle cleaning brush).

NOTE: The materials needed in items (1.) and (2.) can usually be purchased at local hardware stores.

(3.) Insert twisted wire end of brush into end of spring cable, and crimp tight with crimping tool or strike with ball-peen hammer. TIGHTNESS IS VERY

IMPORTANT.

(4.) Remove metal screw fitting from wire brush to allow insertion into cable.

b. Clean each heat exchanger cell.

(1.) Attach variable-speed, reversible drill to end of spring cable (end opposite brush).

(2.) Insert brush end of cable into upper opening of cell and slowly rotate with drill. DO NOT force cable.

Gradually insert at least 36 in. of cable into 2 upper passes of cell. (See Fig. 8.)

—5—

BURNER

13 32

"

11 32 "

CELL

PANEL

HOT

SURFACE

IGNITOR

ASSEMBLY

7 8 "

IGNITOR

BURNER

IGNITOR

ASSEMBLY

A93347

Fig. 7—Position of Ignitor to Burner

A91252

Fig. 8—Cleaning Heat Exchanger Cell

(3.) Work cable in and out of cell 3 or 4 times to obtain sufficient cleaning. DO NOT pull cable with great force. Reverse drill and gradually work cable out.

(4.) Insert brush end of cable in lower opening of cell, and proceed to clean 2 lower passes of cell in same manner as 2 upper passes.

(5.) Repeat foregoing procedures until each cell in furnace has been cleaned.

(6.) Using vacuum cleaner, remove residue from each cell.

(7.) Using vacuum cleaner with soft brush attachment, clean burner assembly.

(8.) Reinstall cell outlet plates and screws FIRST; then, reinstall cell inlet plates and burner assembly. Care must be exercised to center burners in cell openings.

12. Remove old sealant from center panel and collector box flange and apply new sealant to collector box flange and reinstall on center panel, making sure all screws are secure.

FIELD 24-V WIRING

FIELD 115-, 208/230-, 460-V WIRING

FACTORY 24-V WIRING

FACTORY 115-V WIRING

1-STAGE THERMOSTAT TERMINALS

W Y R G C

FIVE

WIRE

TWO-WIRE

HEATING-

ONLY

BLK BLK

W2

COM

WHT WHT

W/W1

GND

GND

115-V FUSED

DISCONNECT

SWITCH

(WHEN REQUIRED)

JUNCTION

BOX

CONTROL

BOX

Y/Y2

R

G

24-V

TERMINAL

BLOCK

FURNACE

NOTES:

GND

GND

CONDENSING

UNIT

FIELD-SUPPLIED

FUSED DISCONNECT

GND

GND

1. Connect Y-terminal as shown for proper operation.

208/230- OR

460-V

THREE

PHASE

208/230-V

SINGLE

PHASE

2. Some thermostats require a "C" terminal connection as shown.

3. If any of the original wire, as supplied, must be replaced,

use same type or equivalent wire.

A99071

Fig. 9—Heating and Cooling Application Wiring Diagram for Single-Stage Thermostats and Single-Speed Condensing Units

NOTE: A releasing agent such as PAM cooking spray or equivalent (must not contain corn or canola oil, aromatic or halogenated hydrocarbons or inadequate seal may occur) and RTV sealant

(G.E. 162, 6702, or Dow-Corning 738) are needed before starting installation. DO NOT substitute any other type of RTV sealant.

G.E. 162 (P771-9003) is available through RCD in 3-oz tubes.

13. Reinstall relief box and inducer assembly.

NOTE: If inducer assembly gasket is damaged, use RTV sealant to seal inducer assembly to collector box.

14. Reconnect wires to the following components: a. Draft safeguard switch.

b. Inducer motor.

c. Pressure switches.

d. Limit overtemperature switch(es).

e. Gas valve.

f. Hot surface ignitor.

g. Flame-sensing electrode.

h. Flame rollout switch(es), if applicable.

15. Reinstall internal vent pipe and enclosure on downflow furnaces only by reversing items 4a through 4c.

NOTE: A releasing agent such as PAM cooking spray or equivalent (must not contain corn or canola oil, aromatic or halogenated hydrocarbons or inadequate seal may occur) and RTV sealant (G.E. 162, 6702, or Dow-Corning 738) are needed before starting installation. DO NOT substitute any other type of RTV sealant. G.E. 162 (P771-9003) is available through RCD in 3-oz tubes.

16. Reinstall vent connector to furnace flue collar. After fully assembling vent connector to furnace flue collar, securely fasten vent connector to flue collar with 2 field-supplied, corrosion-resistant, sheet metal screws located 180 degrees apart and midway up the collar.

17. Replace blower access door only.

18. Turn power and gas to ON.

IV.

19. Set thermostat and check furnace for proper operation.

20. Verify blower airflow and speed changes between heating and cooling.

21. Check for gas leaks.

22. Replace control door.

WARNING: Never use a match or other open flame to check for gas leaks. Use a soap-and-water solution. A failure to follow this warning could result in fire, personal injury, or death.

ELECTRICAL CONTROLS AND WIRING

NOTE: There may be more than 1 electrical supply to unit.

The electrical ground and polarity for 115-v wiring must be maintained properly. Refer to Fig. 9 and 10 for field wiring information and to Fig. 11 for unit wiring information. If the polarity is NOT correct, the furnace control will display rapid flashing on the status LED and prevent heat operation. The control system also requires an earth ground for proper operation of the microprocessor.

With power disconnected to unit, check all electrical connections for tightness. Tighten all screws on electrical connections. If any smoky or burned connections are noticed, disassemble the connection, clean all parts and stripped wire, and reassemble properly and securely. Electrical controls are difficult to check without proper instrumentation; therefore, reconnect electrical power to unit and observe unit through 1 complete operating cycle.

The 24-v circuit contains an automotive-type, 3-amp fuse located on the main control. Any 24-v electrical shorts during installation, service, or maintenance could cause this fuse to blow. If fuse replacement is required, use ONLY a 3-amp fuse. The control will display code 24 when fuse needs replacement.

The control in this furnace is equipped with an LED status light to aid in installation, servicing, and troubleshooting. It can be viewed through the sight glass or window on blower access door. The control indicates status with the LED on continuously, rapid

—6—

FIELD 24-V WIRING

FIELD 115-, 208/230-, 460-V WIRING

FACTORY 24-V WIRING

FACTORY 115-V WIRING

2-STAGE THERMOSTAT TERMINALS

W2 W1 Y2 R G Y1 C SEVEN

WIRE

FIELD-SUPPLIED

FUSED DISCONNECT

THREE-WIRE

HEATING-

ONLY

BLK BLK

W2

COM

WHT WHT

W/W1

GND

GND

115-V FUSED

DISCONNECT

SWITCH

(WHEN REQUIRED)

JUNCTION

BOX

CONTROL

BOX

Y/Y2

R

G

24-V

TERMINAL

BLOCK

FURNACE

GND

C

Y1

Y2

GND

2-SPEED

CONDENSING

UNIT

GND

GND

208/230- OR

460-V

THREE

PHASE

208/230-V

SINGLE

PHASE

NOTES: 1. Connect Y-terminal as shown for proper operation.

2. Some thermostats require a "C" terminal connection as shown.

3. If any of the original wire, as supplied, must be replaced,

use same type or equivalent wire.

A99072

Fig. 10—Heating and Cooling Application Wiring Diagram for 2-Stage Thermostats and/or 2-Speed Condensing Units flashing, or a code composed of 2 digits. (The first digit is the number of short flashes, the second is the number of longs flashes.)

Refer to service label on blower compartment door for code explanations and useful troubleshooting suggestions. (See Fig. 12.)

It is important to note that power to furnace must not be interrupted and furnace blower door must not be removed until the LED status code(s) is recorded. When power to control is interrupted, status memory is erased.

The control will store up to 5 previous codes but will not store non-current codes longer than 48 hr. To retrieve previous codes, if present, no thermostat inputs to control must be present and all time delays must expire. Remove 1 of the red main limit wires 1 to 4 sec until the LED light goes out, then reconnect it. (See Fig.

5 and 6.) (Do not leave red wire disconnected for longer than 4 sec as control will assume an overtemperature condition exists and will respond with indoor blower operation.) This places control in status recall mode and displays first code stored in memory.

Record code and repeat the disconnect and reconnect of red wire, recording each code until code 11 is displayed indicating no additional faults. After last code is displayed or after 2 minutes in the code recall mode, the control will return to normal standby mode.

Use any recorded fault codes, service label, and troubleshooting diagram on following pages to diagnose and correct any problem condition.

WIRING DIAGRAMS

Refer to Fig. 9, 10, and 11 for appropriate wiring diagrams.

TROUBLESHOOTING

Refer to service label. (See Fig. 12.) The Troubleshooting Guide can be a useful tool in isolating furnace operation problems.

Beginning with the word “Start,” answer each question and follow the appropriate arrow to the next item.

The Guide will help you identify the problem or failed component.

After replacing any component, verify correct operation sequence.

More information is available in a seperate Troubleshooting Guide for 2-stage Gas-Fired Induced-Combustion Furnaces.

—7—

CONNECTION DIAGRAM

LS FRS2 LPS NOTE #8

RED

GRY

BRN

HPS

BRN

P

HI

GV

LGPS

DSS

BLU

M

C

GRN/YEL

GRN/YEL

HSI

1

PL6

2

BLK

IDM

HEAT

SET-UP

SWITCH

NORM

HI HT

LO HT

*

FRS1

(WHEN USED)

SWITCH

1 2

ALS1

ORN

(WHEN USED)

NOTE #6

ALS2

WHT

GRN/YEL

BLK

1 2 3 PL3

ILK JB

L1

L2

FUSED DISCONNECT

SWITCH (WHEN REQ’D)

NOTE #1

BLK

WHT FU2

GND

ORN

BLOWER-

OFF DELAY

(SEC.)

90 SEC

135 SEC *

180 SEC

225 SEC

SWITCH

3 4

2-STAGE

FURNACE

CONTROL

PL2 BLK

RED

WHT

BLK

*

BLOWER-OFF DELAY

BLOWER-OFF DELAY

LOW-HEAT ONLY

HIGH-HEAT ONLY

ORN

RED

RED

PR1

L1

PR2

L2

HI-COOL

COMMON

W2 Com

24V

W/W1 Y/Y2 R

TWIN

TEST

M

TJ

G HUM

LED

S

P1

HI-GAS

HEAT

LO-GAS

HEAT

EAC-2

EAC-1

SPARE SPARE

SEC1

SEC2 FU1

BLU

LEGEND

ALS1

ALS2

AUXILIARY LIMIT SWITCH, OVERTEMP. MANUAL RESET, SPST (N.C.)

AUXILIARY LIMIT SWITCH, OVERTEMP. AUTO RESET, SPST (N.C.)

BHI / LOR BLOWER MOTOR SPEED CHANGE RELAY, SPDT

BHT / CLR BLOWER MOTOR SPEED CHANGE RELAY, SPDT

BLWM BLOWER MOTOR, 4 or 5 -SPEED, PERMANENT-SPLIT-CAPACITOR

BLWR

CAP

CPU

DSS

EAC-1

EAC-2

FRS1

FRS2

BLOWER MOTOR RELAY, SPST (N.O.)

CAPACITOR

MICROPROCESSOR AND CIRCUITRY

DRAFT SAFEGUARD SWITCH (N.C.)

ELECTRONIC AIR CLEANER CONNECTION (115 VAC, 1 AMP MAX.)

ELECTRONIC AIR CLEANER CONNECTION (COMMON)

FLAME ROLLOUT SWITCH OVERTEMP. MANUAL RESET, SPST (N.C.)

FLAME ROLLOUT SWITCH OVERTEMP. MANUAL RESET, SPST (N.C.)

FSE

FU1

FU2

GV

HPS

HPSR

HSI

FLAME-PROVING SENSOR ELECTRODE

FUSE, 3 AMP, AUTOMOTIVE BLADE TYPE, FACTORY INSTALLED

FUSE, FIELD INSTALLED

GAS VALVE, REDUNDANT LOW-HEAT OPERATORS, 2-STAGE

HIGH-HEAT PRESSURE SWITCH, SPST (N.O.)

HIGH-HEAT PRESSURE SWITCH RELAY, SPST (N.C.)

HOT-SURFACE IGNITER (115 VAC)

HSIR

HUM

IDM

IDR

HOT-SURFACE IGNITOR RELAY, SPST (N.O.)

24VAC HUMIDIFIER CONNECTION (0.5 AMP. MAX.)

INDUCED DRAFT MOTOR, 2-SPEED, SHADED-POLE

INDUCER MOTOR RELAY, SPST (N.O.)

IHI / LOR INDUCER MOTOR SPEED CHANGE RELAY, SPDT

ILK

JB

LED

BLOWER DOOR INTERLOCK SWITCH, SPST (N.O.)

JUNCTION BOX

LIGHT-EMITTING DIODE FOR STATUS CODES

LGPS

LPS

LS

LOW GAS-PRESSURE SWITCH, SPST (N.O.)

LOW-HEAT PRESSURE SWITCH, SPST (N.O.)

LIMIT SWITCH, OVERTEMPERATURE-AUTO RESET, SPST (N.C.)

WHT

NOTE #4

HI

COM

MED HI

NOTE #15

MED LO

MED

LO

RED

WHT

BLK

YEL

ORN

BLU

RED

BRN

MGVR

PL1

PL2

PL3

PL6

SW1

SW2

SW3 & 4

TJ

TRAN

TWIN/TEST

CAP

BRN

BLWM

WHT

BLK

TRAN

MAIN GAS VALVE RELAY, DPST (N.O.)

-

1 = VALVE

-

2 = HUMIDIFIER

12-CIRCUIT CONNECTOR

9-CIRCUIT CONNECTOR

3-CIRCUIT IDM CONNECTOR

2-CIRCUIT HSI CONNECTOR

HIGH-HEAT-ONLY SWITCH, SPST (MANUAL) *

LOW-HEAT-ONLY SWITCH, SPST (MANUAL)

*

BLOWER-OFF DELAY SETTING SWITCHES,

SPST (MANUAL)

*

TWINNING JUMPER, SPDT FOR MAIN OR

SECONDARY STATUS (MANUAL CHANGE OVER)

TRANSFORMER-115VAC/24VAC

1-CIRCUIT TWINNING BUSS CONNECTOR,

ALSO STATUS CODE RECALL

JUNCTION

TERMINAL

CONTROL TERMINAL

FACTORY POWER WIRING (115VAC)

FACTORY CONTROL WIRING (24VAC)

FIELD POWER WIRING (115VAC)

FIELD CONTROL WIRING (24VAC)

CONDUCTOR ON CONTROL

FIELD WIRING SCREW TERMINAL

FIELD GROUND

EQUIPMENT GROUND

FIELD SPLICE

PLUG RECEPTACLE

TO 115VAC FIELD

DISCONNECT SWITCH

ILK

L1

BLWR

HSIR

IDR

FU1

NOTE #5

PR1

W/W1

G

HUM

TWIN

TEST

R

SW1

W2

Y/Y2

C

OM

S

EQUIPMENT

GROUND

BHI / LOR

BHT / CLR

SCHEMATIC DIAGRAM

NOTE #1

(NATURAL GAS & PROPANE)

HI-COOL

LO-GAS-HEAT

HI-GAS-HEAT

LO

MED LO

NOTE #15

SPARE

SPARE

MED

MED HI

HI

COM

NOTE #4

BRN

COMMON

BLWM

L2

BRN

EAC-1 EAC-2

CAP

IHI / LOR

PL2 3

PL6

9

1

2

HSI

PR2

4

PL3

7

8

LO

2

1

HI

3 COM

IDM

SEC1

115VAC

TRAN

24VAC

SEC2

HPSR

MGVR-2

1

5

6

N/A

N/A

2

12 N/A

2

3

FRS1

(WHEN USED)

FRS2

LS

M

TWINNING

JUMPER

TJ

CPU

NOTES:

1. Use only copper wire between the disconnect switch and the unit.

2. If any of the original wire, as supplied, must be replaced, use the same or equivalent type wire.

3. Inducer (IDM) and blower (BLWM) motors contain internal auto-reset thermal overload switches.

4. Blower motor speed selections are for average conditions. See Installation Instructions for details on optimum speed selection.

5. Replace only with a 3-AMP fuse.

6. Auxiliary limit switches (ALS1 & 2) used on some horizontal and some downflow models.

7. This wire must be connected to furnace sheet metal for control to prove flame.

8. Factory connected when LGPS not used.

MGVR-1

PL1

9

6

DSS

NOTE #8 LPS

5

(WHEN USED)

LGPS

NOTE #8

4

HPS

1

10

C

NOTE#7

M

GV

P

HI

7

8 N/A

11 N/A

ALS2

FSE

ALS1

9. Symbols are an electrical representation only.

10. BLOWER-ON DELAY: Gas heating 45 seconds,

Cooling/Heat Pump 2 seconds.

11. Cooling/Heat Pump BLOWER-OFF DELAY is 90 seconds.

12. IGNITION-LOCKOUT will occur after four consecutive unsuccessful trials-for-ignition.

Control will automatically reset after three hours.

13. Control must be grounded at pin 10 of 12-pin connector.

14. NA - Not Applicable

15. Spare terminal and wire not available on some applications. Insulate connector if not available.

324459-101 REV. D

A01365

→ Fig. 11—Unit Wiring Diagram

SERVICE

If status code recall is needed, do not remove power or blower door. Briefly remove and then reconnect one main limit wire to display stored status code.

LED CODE STATUS

CONTINUOUS OFF

CONTINUOUS ON

RAPID FLASHING

- Check for 115VAC at L1 and L2, and 24VAC at SEC1 and SEC2 .

- Control has 24VAC power.

- Line voltage (115VAC) polarity reversed. If twinned, refer to

twinning kit instructions.

Each of the following status codes is a two-digit number with the first digit determined by the number of short flashes and the second digit by the number of long flashes.

11 NO PREVIOUS CODE - Stored status codes are erased when power (115VAC or

24VAC) to control is interrupted or 48 hours after each fault is cleared.

12 BLOWER ON AFTER POWER UP (115VAC or 24VAC) - Blower runs for 90 seconds, if unit is powered up during a call for heat (R-W closed).

13 LIMIT OR FLAME ROLL-OUT SWITCH LOCKOUT - Control will auto reset after three hours. Reset switch or replace fuse link. Refer to #33.

14 IGNITION LOCKOUT - Control will auto-reset after three hours. Refer to #34.

21 GAS HEATING LOCKOUT - Control will NOT auto-reset.

Check for: - Mis-wired gas valve - Defective control (valve relay)

22 ABNORMAL FLAME-PROVING SIGNAL - Flame is proved while gas valve is deenergized. Inducer will run until fault is cleared. Check for:

- Leaky gas valve - Stuck-open gas valve

23 PRESSURE SWITCH DID NOT OPEN Check for:

- Obstructed pressure tubing - Pressure switch stuck closed.

24 SECONDARY VOLTAGE FUSE IS OPEN Check for: - Short-circuit in secondary voltage (24VAC) wiring

31 HIGH-HEAT PRESSURE SWITCH OR RELAY DID NOT CLOSE OR REOPENED

Check for: -Control relay may be defective - Refer to #32

32 LOW-HEAT PRESSURE, DRAFT SAFEGUARD (when used), OR AUX-LIMIT (when used*)

SWITCH DID NOT CLOSE OR REOPENED (DOWNFLOW ONLY*) If open longer than five minutes, inducer shuts off for 15 minutes before retry. If it opens after trial for ignition period, blower will come on for 90 second recycle delay. Check for:

*- Defective blower motor or capacitor

- Proper vent sizing

- Restricted vent

- Low inducer voltage (115VAC)

- Disconnected or obstructed pressure tubing - Excessive wind

- Defective inducer motor - Defective pressure switch

- Inadequate combustion air supply - Low propane inlet gas pressure

33 LIMIT OR FLAME ROLL-OUT SWITCH IS OPEN - If open longer than three minutes, code changes to #13. Flame roll-out switch requires manual reset. Check for:

- Dirty filter or restricted duct system. - Loose blower wheel.

- Defective blower motor or capacitor. - Defective switch or connections.

- Inadequate combustion air supply (Flame roll-out switch or fuse link open).

- Open flame roll-out switch, or fuse link. Manual reset or replace.

34 IGNITION PROVING FAILURE - Control will try three more times before lockout #14 occurs. If flamesignal is lost after trial for ignition period, blower will come on for

90 second recycle delay. Check for:

- Gas valve defective or gas valve turned off.

- Oxide buildup on flame sensor (clean with fine steel wool).

- Proper flame sense current (.5 microamps D.C. min., 4.0 - 6.0 nom. in HIGH HEAT).

- Green wire MUST be connected to furnace sheet metal.

- Flame sensor must be ungrounded. - Manual valve shut-off.

- Defective hot surface ignitor - Control ground continuity.

- Inadequate flame carryover or rough ignition. - Low inlet gas pressure.

43 LOW-HEAT PRESSURE, DRAFT SAFEGUARD (when used), OR AUX-LIMIT (when used*)

SWITCH OPEN WHILE HIGH-HEAT PRESSURE SWITCH IS CLOSED Check for:

- Pressure switch stuck open - Disconnected or obstructed pressure tubing

- Refer to #32 and #33 - Low propane inlet gas pressure

45 REPLACE CONTROL

COMPONENT TEST

W2

C OM

24 V

W/W1 Y/Y2 R G HUM LED

TWIN

TEST

12 - CIRCUIT

CONNECTOR

To initiate the component self-test sequence, shut off the room thermostat or disconnect the "R" thermostat lead. Briefly short the TWIN/TEST terminal to the

Com24V terminal. Status LED will turn off. NON-CONDENSING FURNACE: The control will turn ON the inducer motor low speed, then high speed and remain on high speed for the entire test. The other components will be ON for 7 to 15 seconds: Hot surface ignitor, Low heat blower speed, High heat blower speed,

High cooling blower speed. CONDENSING FURNACE: The inducer motor will start in high speed and remain on high speed until the end of the test, then shift to low speed for 7 to 15 seconds. All other components will be tested in the same sequence as the NON-CONDENSING.

320893-101 REV. F

Fig. 12—Service Label

—9—

A01368

NOTES:

1.

Refer to information label on blower compartment door for procedure for use of LED status codes and problem solving suggestions.

2.

LED indicator is viewed through window in blower compartment door.

3.

If 115-vac power is de-energized or interrupted during a call for heat, the indoor blower will run for 90 sec before

4.

a gas heating cycle begins – Code 12.

After replacing any component, verify correct operating sequence.

START

Turn thermostat OFF.

On furnace control, note current settings for setup switches 1 (SW-1) and 2 (SW-2) then set SW-1 to OFF and SW-2 to ON.

Cycle 115-v power off for 3 sec, then on.

Continuous LED?

Yes

Set thermostat to call for heat.

Set FAN to AUTO mode.

No

Draft inducer motor starts.

Yes

Is Code 22 displayed?

Yes

Flame present when not normal.

Replace gas valve.

No

15-sec inducer pre-purge.

Yes

Ignitor warms up and glows orange/yellow; 17-sec warm-up.

Yes

Main burners ignite.

Yes

No

No

Main burners stay on.

Yes

Indoor blower motor starts on heating speed after 45-sec warm-up period.

Yes

No

No

No

TROUBLESHOOTING

GUIDE

If LED is flashing rapidly, check line voltage polarity.

If Code 24 is displayed, check for blown fuse.

If LED is OFF, check line voltage and 24-v transformer.

If Code 45 is displayed, replace control.

Is indoor blower on ?

No

24v should be present across Com and W at furnace control. If not, check for:

1. Open thermostat.

2. Open 24-v fuse (FU1) – Code 24.

3. Failed transformer.

If Code 23 is displayed, the pressure switch(es) is stuck closed.

Replace switch and/or check pressure tube for blockage.

System malfunction – Code 21.

115v should be present at the inducer motor. If so, replace inducer motor. If not, check 115-v wiring.

Yes

No

If Code 32 is displayed check for:

1. Open gas inlet pressure switch (when used).

2. Open pressure switch (LPS) and/or tube – Code 32.

3. Open draft safeguard switch (DSS) – Code 32.

4. Open auxiliary switch (ALS)(downflow only) – Code 32.

5. Check all low-voltage wiring connections.

115v should be present at the ignitor. If so, replace the ignitor; if not, check 115-vac wiring to ignitor.

LPS, DSS, or ALS open while HPS if closed (high-gas-heat only) –

Code 43.

No

Control will attempt to light burners 4 times (approximately 1 minute between attempts – Code 34). Voltage is present at the gas valve for 7 sec during each ignition trial. System will lockout after 4 attempts.

Is the gas valve control knob or switch in the OPEN or ON position?

24v should be present across the gas valve terminals C and M/P

(and C and HI for high-stage gas test) during the 7 sec ignition trial. If not, check all low-voltage wiring connections to valve.

If 24v are present, and main gas does not flow:

1. Supply pressure between 4.5- and 13.6-in. wc. If not, adjust supply pressure.

2. If supply pressure is between 4.5- and 13.6-in. wc, replace gas valve.

Check ignitor position.

Check burner carryover gap.

Check gas supply pressure (4.5-in. wc minimum).

Check manifold pressure (1.3- to 1.7-in. wc for low-stage gas;

3.2- to 3.8-in. wc for high-stage gas).

Check for proper orifice size.

No

Is Code 31 (high-gas-heat only), 32, 33, or 34 displayed? Check code information label to diagnose.

Check polarity of 115-v power at J-box and control. Twinned furnace polarities must match – rapid flashing LED.

Check ground continutity from J-box to control.

Check flame sensor microamps (4.0 nominal; 0.5 minimum for control to recognize flame).

No

No

115v should be present at the blower motor. If so, check capacitor.

If capacitor is OK, replace blower motor. If 115v are not present at the blower motor, check all 115-v wiring to motor.

Furnace runs until call for heat ends.

Yes

Turn thermostat to OFF; gas valve shuts off burners; 5-sec inducer post purge.

Yes

Indoor blower motor stops after

90, 135, 180, or 225 sec.

Yes

Heating sequence of operation complete. Remove blower door, move setup switch 1 (SW-1) to ON position and repeat process to check high-stage gas heat operation.

(When finished return SW-1 and

SW-2 to original desired settings.)

No

No

No

If not, check for:

1. Satisfied thermostat.

2. Open inlet gas pressure switch (when used).

3. Open pressure switch (LPS) – Code 32.

4. Open draft safeguard switch (DSS) – Code 32.

5. Open auxilliary limit (ALS)(downflow only) – Code 32.

6. Open 24-v fuse (FU1) – Code 24.

7. Open limit switch (LS) – Code 13 or 33.

8. Open flame rollout switch (FRS) – Code 13 or 33.

9. Check 115-v line voltage – LED off.

Check for sources of electrical noise interference (electronic air cleaners, nearby TV, or radio antennas).

If inducer and burners continue to operate, check for 24v at the gas valve. If 24v are present, verify that the thermostat is open across R and W. If no voltage is present, turn the gas valve control knob or switch to the OFF position. Replace gas valve.

24v should be present across R and Com. If not, check for:

1. Open limit switch (LS) – Code 13 or 33.

2. Open flame rollout switch (FRS) – Code 13 or 33.

24v should not be present across R and G. If so, set thermostat

FAN to AUTO mode.

No

No

No

!

WARNING

ELECTRICAL SHOCK HAZARD

ONLY QUALIFIED AND TRAINED

SERVICE PERSONNEL SHOULD

PERFORM THIS PROCEDURE

24v should be present across R and Com. If not, check for:

1.

Open flame rollout switch

(FRS) – Code 33.

2.

Open limit switch (LS) –

Code 33.

3.

Check all low-voltage wiring connections.

No

Replace control only if all checks are OK.

Replace control only if Code 45 is displayed, or if all checks are OK.

Replace control only if Code 45 is displayed, or if all checks are OK.

Replace control if Code 45 is displayed, or if all checks are OK.

Clean flame sensor if microamps are below nominal.

Replace control only if Code 45 is displayed, or if all checks are OK.

Replace control only if Code 45 is displayed, or if all checks are OK.

Replace control only if Code 45 is displayed, or if all checks are OK.

Replace control only if Code 45 is displayed, or if all checks are OK.

A97544

—10—

SERVICE TRAINING

Packaged Service Training programs are an excellent way to increase your knowledge of the equipment discussed in this manual, including:

• Unit Familiarization

• Installation Overview

• Maintenance

• Operating Sequence

A large selection of product, theory, and skills programs is available, using popular video-based formats and materials. All include video and/or slides, plus companion book.

Classroom Service Training plus "hands-on" the products in our labs can mean increased confidence that really pays dividends in faster troubleshooting, fewer callbacks. Course descriptions and schedules are in our catalog.

CALL FOR FREE CATALOG 1-800-962-9212

[ ] Packaged Service Training [ ] Classroom Service Training

A94328

—11—

© 2001 Bryant Heating & Cooling Systems 7310 W. Morris St. Indianapolis, IN 46231 —12— Printed in U.S.A.

sp0473 Catalog No. 5333-025

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Questions and Answers

What is the minimum maintenance required for the Bryant 330JAV furnace?
Check and clean the air filter monthly, inspect the blower motor and wheel during each heating and cooling season, and check electrical connections and controls for proper operation annually.
How do I clean or replace the air filter on my Bryant 330JAV furnace?
Turn off the electrical supply to the furnace, remove the blower access door, clean the air filter with tap water, rinse and let it dry, reinstall the filter, and turn on the electrical supply.
How do I clean the blower motor and wheel on my Bryant 330JAV furnace?
Turn off the electrical supply to the furnace, remove the blower access door, disconnect the vent connector and internal vent pipe, remove the vent pipe enclosure, clean the blower motor and wheel with a vacuum cleaner and soft brush, and reassemble the furnace.
How often should I clean the air filter on my Bryant 330JAV furnace?
Once a month or more frequently if required.
What precautions should be taken to prevent Electrostatic Discharge (ESD) damage to the Bryant 330JAV furnace control?
Disconnect all power to the furnace, touch a clean, unpainted metal surface of the furnace chassis, use an ESD service kit, and discharge your body's electrostatic charge to ground before handling the control or connecting wires.

Related manuals