WASHING MACHINE
ZWF 1020W
ZWF 1220W
ZWF 1220S
ZWF 1420W
Whites
Whites Economy
Coloured Economy
Colour care
Synthetics
Synthetics
Synthetics
40°
Delicates
95°
60°
40°
30°
60°
40°
30°
Off O
Handwash
Wool
Wool Cold
Miniprogram
Spin
30°
40°
Programme
ZWF 1020 W
30°/30‘
Rinses
Drain
Spin
Options
Half
Load
Easy
Iron
Start/
Pause
12 H
Delay
Start
8H
4H
2H
Washing
ESSENTIAL
132989080
1000
AQUAC YCLE
End
INSTRUCTION BOOKLET
GB
Important Safety Information
It is most important that this instruction book should be retained with the appliance for future
reference. Should the appliance be sold or transferred to another owner, or should you move
house and leave the appliance, always ensure that the book is supplied with the appliance in
order that the new owner can get to know the functioning of the appliance and the relevant
warnings.
These warnings have been provided in the interest of safety. You MUST read them carefully
before installing or using the appliance.
Installation
●
●
●
●
●
●
●
Use
This appliance is heavy. Care should be taken when
moving it.
It is dangerous to alter the specifications or attempt
to modify this product in any way.
All packing and transit bolts must be removed before
use. Serious damage can occur to the product and to
property if this is not adhered to. See relevant section
in instructions.
Any plumbing work required to install this appliance
should be carried out by a qualified plumber or
competent person.
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
Care must be taken to ensure that the appliance does
not stand on the electrical supply cable.
If the machine is situated on a carpeted floor, please
adjust the feet in order to allow air to circulate freely.
●
●
●
●
●
●
Child Safety
●
●
●
●
●
●
This appliance is designed to be operated by adults.
Children should not be allowed to tamper with the
controls or play with the product.
Pets and children have been known to climb into
washing machines. Please check your drum before
use.
The glass door becomes very hot during the washing
cycle. Keep children away from the vicinity of the
appliance whilst it is in operation.
Keep all packaging well away from children.
Keep all detergents in a safe place out of children’s
reach.
●
●
●
●
2
Always unplug the appliance and turn off the water
supply after use.
Do not overload the appliance. See relevant section
in the instruction book.
Only wash fabrics which are designed to be machine
washed. If in doubt, consult the care label on the
clothes.
Before washing, ensure that all pockets are empty
and buttons and zips are fastened. Avoid washing
frayed or torn articles and treat stains such as paint,
ink, rust, and grass before washing. Underwired bras
must NOT be machine washed.
Any objects such as coins, safety pins, nails, screws,
stones or any other hard, sharp material can cause
extensive damage and must not be placed into the
machine.
Garments which have been in contact with volatile
petroleum products should not be machine washed.
If volatile cleaning fluids are used, care should be
taken to ensure that the fluid is removed from the
garment before placing in the machine.
Wash small items such as socks, laces, washable
belts etc in a washing bag or pillow case as it is
possible for such items to slip down between the tub
and the inner drum.
Only use the advised quantities of fabric softener.
Damage to the fabric can ensue if you over-fill.
Refer to the manufacturer’s recommendations of
quantities.
As some duvets and eiderdowns should be washed
in large commercial machines because of their bulk,
please check with the manufacturer of the item
before washing in a domestic machine.
Leave the porthole door slightly ajar between washes
to preserve the door seal.
Under no circumstances should you attempt to repair
the machine yourself. Repairs carried out by
inexperienced persons may cause injury or serious
malfunctioning. Contact your local Service Force
Centre. Always insist on genuine Zanussi spare
parts.
Contents
Maintenance and Cleaning
For the User
Important Safety Information
Your New Washing Machine
Description of the Appliance
Detergent dispenser drawer
Child safety feature
The Control Panel
Programme information
Descaling
After each wash
Maintenance Wash
External cleaning
Cleaning the dispenser drawer
Cleaning the drawer recess
Cleaning the pump
Cleaning the water inlet filter
The dangers of freezing
Emergency emptying out
2
4
5
5
5
6-7
8
Operating Sequence
9-12
Washing 5 kg of white cotton at 95°C
9
Load the laundry
9
Measure out the detergent and the fabric softener
9
Select the required programme
9
Select the spin speed or option
or
9
Select the required option
10
Select the delay start
10
Start the machine
10
Altering a programme
10
Interrupting a programme
10
Cancelling a programme
10
Opening the door after the programme has started
10
At the end of the programme
10
Washing 2 kg of mixed fabrics at 40°C
11
Load the laundry
11
Measure out the detergent and the fabric softener
11
Select the required programme
11
Select the spin speed or option
or
11
Select the required option(s)
11
Start the machine
11
At the end of the programme
12
Washing Hints
Which detergent?....
And in which form?
Wash Care Symbols
Washing Programmes
Something Not Working
Service and Spare Parts
Guarantee Conditions
18-19
18
18
18
18
18
18
18-19
19
19
19
20-21
21
22
For the Installer
Installation Instructions
Technical Specifications
Unpacking
Positioning
Water inlet
Water drainage
Levelling
Special conditions
In the interest of the environment
Electrical connection
13-14
14
14
15
16-17
Guide to use the Instruction Book
The following symbols will be found in the text to guide you throughout the instructions:
Safety instructions
Hints and tips
Environmental information
3
23
23
24
24
24-25
25
26
26
26
27
Your New Washing Machine
Your new washing machine meets all modern requirements for effective treatment of laundry
with low water, energy and detergent consumption.
●
●
●
●
The programme selector dial combines the
function of programme and temperature selection,
making it easier to set the programme.
The programme progress display shows the delay
start, the washing phase and the end of the
programme .
The special wool programme with its new delicate
wash system treats your woollens with extreme care.
The ECO VALVE allows total use of detergent and
reduces water consumption so saving energy.
In the interest
of the environment
●
●
●
Ecological hints
●
To save water and energy and help protect the
environment, we recommend that you follow these
hints:
● Adjust the quantity of detergent according to the
hardness of your water supply, the amount of
laundry and the degree of soiling.
● A programme without prewash is sufficient for
normally soiled laundry.
● The machine works more economically if it is fully
loaded.
● With adequate pre-treatment, stains and limited
soiling can be removed; the laundry can then be
washed at a lower temperature, so saving energy.
Materials marked with the symbol
are
recyclable.
Check with your local Council or Environmental
Health Office to see if there are facilities in your area
for re-cycling this appliance.
When the appliance is to be scrapped, cut off the
power supply cable and make the door lock device
unusable to prevent young children from being
trapped inside.
Help to keep your country tidy - use authorised
disposal sites for your old appliance.
How do we help to protect the environment?
We use recycled paper!
Important
Your machine is fitted with a balance control device, which ensures the machine is stable during the spin.
If the wash load appears not to have been spun sufficiently at the end of the wash cycle, because it is not evenly
distributed in the drum, the balance control device may have operated. It will therefore be necessary to redistribute the
wash load manually and select a spin programme. For more detailed information see the section headed "Something
Not Working".
4
Description of the Appliance
3
1
1Detergent dispenser drawer
2 Programme guide
3 Control panel
4 Door opening handle
5 Drain pump
6 Adjustable feet
Whites
Whites Economy
Coloured Economy
Colour care
Synthetics
Synthetics
Synthetics
40°
Delicates
95°
60°
40°
30°
60°
40°
30°
Off O
Handwash
Wool
Wool Cold
Miniprogram
Spin
30°
40°
Programme
ZWF 1020 W
30°/30‘
Rinses
Drain
Spin
Options
Half
Load
Easy
Iron
Start/
Pause
12 H
Delay
Start
8H
4H
2H
Washing
E SSENTIAL
1000
AQUAC YCLE
End
2
4
5
6
Detergent dispenser drawer
Prewash
Main wash
Fabric softener
C0069
Child safety feature
This machine incorporates a special child safety feature
to prevent small children from being trapped inside the
machine.
To activate this device, rotate the button (without
pressing it) inside the door clockwise until the groove is
horizontal. If necessary use a coin.
To disable this device and restore the possibility of
closing the door, rotate the button anti-clockwise until
the groove is vertical.
P1131
5
The Control Panel
Whites
Whites Economy
Coloured Economy
Colour care
Synthetics
Synthetics
Synthetics
40°
Delicates
95°
60°
40°
30°
60°
40°
30°
Off O
Handwash
Wool
Wool Cold
Miniprogram
30°
40°
Spin
Programme
8
9
ZWF 1020 W
30°/30‘
Rinses
Drain
Spin
Options
Half
Load
Easy
Iron
Start/
Pause
12 H
Delay
Start
8H
4H
2H
Washing
ESSENTIAL
AQUAC YCLE
1000
1
End
2 3 4 5 6 7
1 Detergent dispenser drawer
3 HALF LOAD button
Programme Option buttons
Select this button to reduce water consumption on the
rinse cycle when washing a smaller load of cottons or
linens (maximum load size = 2.5 kg).
The machine will perform 2 rinses instead of 3.
Depending on the programme, different functions can
be combined. These must be selected after choosing the
desired programme and before depressing the
START/PAUSE button.
When these buttons are pressed, the corresponding pilot
lights come on. When they are pressed again, the pilot
lights go out.
If an incorrect option is selected, the corresponding
pilot light flashes for about 2 seconds.
4 EASY IRON button
Selecting this button the laundry is gently washed and
spun to avoid any creasing. In this way ironing is easier.
Furthermore the machine will perform 6 rinses instead
of 3 for cotton and 4 rinses instead of 3 for synthetics.
This function can be used for cotton and synthetic
fabrics.
2 Options button
5 Start Pause button
By depressing this button you can select two different
options:
●
(PREWASH): select this option if you wish
your laundry to be prewashed before the main wash
(not available for wool, handwash and
Miniprogram).
The prewash ends with a short spin in programmes
for cotton and synthetic fabrics, whereas in the
programme for delicate fabrics the water is only
drained.
●
(QUICK): a very short cycle for cotton,
synthetic or delicate items that have been used or
worn for a short time.
This opti on cannot be used with the Economy
programme 60E and E40
Max. recommended load 3.5 kg.
The light corresponding to the selected option
illuminates. If an option is chosen that is not allowed
with the selected programme, both lights will flash 3
times.
After having selected the required programme, press
this button to start the machine; the corresponding pilot
light stops flashing.
To interrupt a programme which is running, depress the
Start/Pause button: the corresponding pilot light starts to
flash.
To restart the programme from the point at which it was
interrupted, press the START/PAUSE button again.
6 DELAY START button
This button makes it possible to delay the starting of the
washing programme by 12, 8, 4 and 2 hours. The delay
you have selected is indicated by the illumination of the
corresponding light.
You must select this option after you have set the
programme and before you press the START
PAUSE button.
You can cancel the delay time at any moment, before
you press the START/PAUSE button.
6
8 Spin speed selector dial
If you have already pressed the START/PAUSE button,
and you wish to cancel the delay time, proceed as
follows:
This dial allows you to reduce the final and the
intermediate spin speeds or to select the NO SPIN
or RINSE HOLD (anti-crease)
option.
• set the washing machine to PAUSE by pressing the
START/PAUSE button;
• press the DELAY button once, the light relevant to the
selected delay goes off .
• press the START/PAUSE button again to start the
programme.
Important!
The speeds on the dial refer to cotton programmes.
Position 1000 (or 1200, 1400) corresponds to 900 r.p.m.
for synthetics, wool and handwash and 700 r.p.m. for
delicates.
Position 500 corresponds to 450 r.p.m. for delicates and
500 r.p.m. for synthetics, wool and handwash.
● NO SPIN
: by selecting this option all the
spinning phases are suppressed. To be used for
extremely delicate items.
The machine will add 3 rinses on cotton
programmes and 1 rinse on synthetic programmes.
● RINSE HOLD (anti-crease)
: by selecting this
option the water of the last rinse is not emptied out
to prevent the fabrics from creasing. When the
programme has finished the phase light END is on
and the door is blocked to indicate that the water
must be emptied out.
To do this:
● turn the programme selector dial to “O”
● select the drain
or spin
programme.
Using the spin speed selector dial you can choose the
desired spin. If the dial remains on position
or
the machine will perform the spin
speed at 400 rpm.
● depress START button.
The selected delay can be changed only after
selecting the washing programme again.
● The door will be locked throughout the delay time.
If you need to open the door, you must first set the
washing machine to PAUSE by pressing the
START/PAUSE button. After you have closed the
door, press the START/PAUSE button again.
●
The delay start can not be selected with SPIN
and DRAIN
programmes.
7 Programme progress display
When you choose the delayed start, the light relevant to
the selected delay lights up.
After the machine has started, the remaining time is
shown by the corresponding indicator light.
At the beginning of the programme, only the
WASHING light stays on. When the programme has
finished, the End pilot light comes on.
9 Programme selector dial
8H
4H
The selector dial is divided into following sections:
● Cotton and linen
● Synthetics
● Delicates
and Handwash
● Wool
● Miniprogram
● Special programmes:
(rinses),
(drain) and
(spin)
2H
Washing
End
The End light flashes in the event of operating
problems:
● 4 flashes: door open
● 2 flashes: problem with water draining
● 1 flash: problem with water supply
For more information see paragraph “Something not
working”?
95
O
0
40
30
4
7
4
0
30 E40
60
6
0E
The selector dial can be turned either clockwise or
anticlockwise.
Position 60E and E40 corresponds to the ENERGY
SAVING programme for cotton, position
to cold
wash and position O to Reset programme/Switching
OFF of the machine.
At the end of the programme the selector dial must
be turned to position O, to switch the machine off.
ATTENTION!
If you turn the programme selector dial to another
programme when the machine is working, the lights of
the programme progress display start to flash. The
machine will not perform the new selected programme.
Spin
Separate spin for hand washed garments and after
programmes with Rinse Hold option
. Before
selecting this programme the selector dial must be
turned to “O”. You can choose the speed by means of
the relevant selector dial to adapt it to the fabrics to be
spun.
Note: if the spin speed selector dial is on positions
1400, 1200, 1000 or 900 r.p.m. the machine performs a
long spin. On positions 700 or 500 r.p.m. the machine
performs a short spin.
Miniprogram
Programme information
This is a complete programme to be used for lightly
soiled laundry or for laundry which needs freshening up.
Max load: 2. kg .
Washing temperature: 30°C
Number of rinses: 2 .
Programme duration: 30 minutes.
Short spin at 700 r.p.m max.
Wool
The wool wash cycle of this machine has been approved
by Woolmark for the washing of machine washable
Woolmark products provided that the garments are
washed according to the instructions on the garment
label and those issued by the manufacturer of this
washing machine. M9604.
Handwash 30°
Particularly delicate washing suitable for articles of
clothing whose label indicates that they must be handwashed .
Rinses
With this programme it is possible to rinse and spin
garments which have been washed by hand.
The machine performs 3 rinses, followed by a final
short spin at the speed selected by means of the relevant
dial.
Drain
For emptying out the water of the last rinse in programmes
with the Rinse Hold
option.
Turn first the programme selector dial to O, then select
drain programme
and depress the START/PAUSE
button.
8
Operating Sequence
3. Select the required programme
Before the first wash, we recommend that you pour 2
litres of water into the main wash compartment
of
the detergent drawer in order to activate the ECO valve.
Then run a synthetic cycle at 60°C, without any laundry
in the machine, to remove any manufacturing residue
from the drum and tub.
Pour 1/2 a measure of detergent into the dispenser
drawer and start the machine.
0
95
60E
O
0
60 30
40
E4
Turn the programme selector dial to the 95 programme.
The light START/PAUSE starts to flash.
40
40
3
WASHING 5 KG OF WHITE COTTON AT 95°C
Suppose you have 5 kg of heavy soiled laundry to wash.
It is white cotton and is suitable for high temperature
washing.
4. Select the spin speed or
option
or
1. Load the laundry
Turn the selector dial to the required position.
ZWF 1020W
ZWF 1220W-S
1000
500
500
ZWF 1420W
P0004
90
0
700
2. Measure out the detergent
and the fabric softener
Pull out the dispenser drawer until it stops.
Measure out the amount of detergent required, pour it
into the main wash compartment
and, if you wish to
carry out the prewash phase, pour it into the
compartment marked .
If required, pour fabric softener into the compartment
marked
(the amount used must not exceed the
“MAX” mark in the drawer). Close the drawer gently.
500
C0070
C0071
9
0
700
700
90
0
90
Open the door by carefully pulling the door handle
outwards.
Place the laundry in the drum, one item at a time,
shaking them out as much as possible. Close the door.
1400
1200
5. Select the required option(s)
8. Altering a programme
Select
or Easy Iron if required, the corresponding
light illuminates.
You can alter the programme before it starts.
When the programme has started, you can only reset it
by turning the programme selector dial to O and then
you can select the new programme.
The washing water remains in the tub.
Start the new programme by depressing the
START/PAUSE button.
Half
Load
Options
Easy
Iron
9. Interrupting a programme
Depress the START/PAUSE button to interrupt a
programme which is running, the corresponding light starts
to flash. Depress the button again to restart the programme.
6. Select the DELAY START
Before you start the programme, if you wish to delay
the start, press the DELAY START button repeatedly, to
select the desired delay. The relevant light illuminates.
12 H
Delay
Start
10.Cancelling a programme
Turn the selector dial to O to cancel a programme which
is running. Now you can select a new programme.
8H
11.Opening the door after the
programme has started
4H
2H
Washing
First set the machine to PAUSE by pressing the
START/PAUSE button.
If the door does not open, this means that the machine is
already heating, that the water level is above the bottom
edge of the door or that the drum is turning.
If you cannot open the door but you need to open it you
have to switch the machine off by turning the selector dial
to “O”. After about 2 minutes the door can be opened
(pay attention to the water level and temperature!).
End
7. Start the programme
Before starting up the machine check that:
● the appliance is plugged in
● the water supply tap is turned on
● the drain hose is correctly and securely positioned
● the door and the detergent dispenser drawer are
closed.
To start the selected programme, press the
START/PAUSE button; the corresponding light stops
flashing.
The WASHING light illuminates.
The machine starts operating.
If you have chosen a
delayed start, the
machine will begin the
Start/
countdown.
Pause
12. At the end of the programme
The machine stops automatically.
If the Rinse Hold
option has been selected, the
phase light END is on and the door is blocked to
indicate that the water must be emptied out before
opening the door.
To do this first turn the programme selector dial to “O”
and then to drain programme
or spin programme .
Release of the lock is also indicated by the coming on of
the END light.
Turn the programme selector dial to “O” to switch the
machine off. Remove the laundry from the drum and
carefully check that the drum is empty.
If you do not intend to carry out another wash, close the
water tap. Leave the door open to prevent the formation
of mildew and unpleasant smells.
10
4. Select the required
programme
WASHING 2 KG OF MIXED FABRICS AT 40°C
Suppose you have 2 kg of lightly soiled mixed fabrics to
wash. They are rather delicate fabrics and should not be
washed at a high temperature.
Turn the programme selector dial to the 40 programme.
The START/PAUSE light starts to flash.
1. Load the laundry
40 60
30
40
30
60E 95
40
E40
Open the door by carefully pulling the door handle
outwards.
Place the laundry in the drum, one item at a time,
shaking them out as much as possible. Close the door.
O
5. Select the spin speed or
option
or
Turn the selector dial to the required position.
ZWF 1020W
P0004
1000
90
0
700
2. Measure out the detergent
Pull out the dispenser drawer until it stops.
Measure out the amount of detergent required and pour
it into the main wash compartment .
If you wish to carry out the prewash phase, pour the
detergent into the compartment marked .
500
6. Select the required option(s)
Select PREWASH
or QUICK
and/or EASY
IRON if required, the corresponding light illuminates.
Options
C0070
3. Measure out the fabric
softener
Half
Load
Easy
Iron
7. Start the machine
If required, pour fabric softener into the compartment
marked
(the amount used must not exceed the
“MAX” mark in the drawer).
Close the drawer gently.
Before starting up the machine check that:
● the appliance is plugged in
● the water supply tap is turned on
● the drain hose is correctly and securely positioned
● the door and the detergent dispenser drawer are
closed.
To start the selected programme, press the
START/PAUSE button; the corresponding light stops
flashing.
C0071
11
The WASHING pilot light illuminates.
The machine starts operating.
Start/
Pause
8. At the end
of the programme
The machine stops automatically.
If the Rinse Hold
option has been selected, the
phase light END is on and the door is blocked to
indicate that the water must be emptied out before
opening the door.
To do this first turn the programme selector dial to “O”
and then to drain programme
or spin programme .
The door can then be opened.
Release of the lock is also indicated by the illumination
of the END light.
Turn the programme selector dial to “O” to switch the
machine off.
Remove the laundry from the drum and carefully check
that the drum is empty.
If you do not intend to carry out another wash, close the
water tap.
Leave the door open to prevent the formation of mildew
and unpleasant smells.
12
Washing Hints
Do NOT overload the machine. Weigh the laundry the
first few times you use the appliance.
●
The average weights of the most common items are
listed below as a guide:
●
●
1000g = 1 kg
Sheet
700-1000 g
Pillow case
100-200 g
Tablecloth
400-500 g
Serviette
50-100 g
Tea towel
70-120 g
Linen hand towel
100-150 g
Towelling hand towel
150-250 g
Towelling bath towel
700-1000 g
Bath robe
200-300 g
Apron
150-200 g
●
●
●
●
●
●
●
●
●
●
●
●
1000-1500 g
Man’s shirt
●
●
●
Load the laundry loosely alternating large items with
small ones.
Sort the laundry according to the type of fabric,
colour-fastness and how dirty it is.
Avoid washing unhemmed or torn items as they may
unravel.
Before washing, empty all pockets of small objects
which may have been left inside (coins, keys, screws
etc.) as these could damage the drain pump.
When washing curtains, remove the hooks.
Close poppers and zips and fasten loose buttons.
It is essential to wash new coloured items separately
when washing for the first time.
When washing fabrics requiring different wash
temperatures together, always select the lowest
temperature.
White items should not be washed with coloured
items.
Very small items (handkerchiefs, ribbons, socks etc)
should be washed in a washing bag or a pillow case.
Use a good quality detergent suitable for automatic
washing machines.
Use the correct quantities of detergent.
13
For wool, use gentle detergent only in small
quantities.
Bleach is very corrosive; it should be used with care
and kept out of reach of children.
Some stains such as fruit, wine, grass, rust etc. are
difficult to remove and should be treated before
washing with specific products, which can be found
in most household shops. In some cases it may help
to soak the stain before washing with a special presoak product or biological detergent.
Only wool marked “Pure New Wool - washable,
preshrunk” can be washed in the machine using the
wool programme; other types of wool should be
washed in HANDWASH programme.
If you have used the machine to wash, rinse or spin
only non-colour fast garments, there may be dye left
in the sump. To ensure any subsequent wash is not
contaminated with the dye, select and carry out a
rinse and spin programme, without any garments, to
ensure that any dye is removed from the sump.
Once you have finished using the machine, you are
advised to unplug it and turn off the water tap.
Which detergent?....
And in which form?
To ensure you obtain the best wash results from your
appliance, it is important to use the right detergent in
your everyday wash, and only detergents recommended
for use in automatic machines.
To maintain the appearance of your clothes and
household textiles and to make them last longer you
should use different types of detergent for different
washes, whether for whites, colours or delicates.
Not only are there different types of detergent, but they
are also available in different forms. Whether you chose
a powder or liquid in traditional or compact form is
your own personal choice.
TRADITIONAL POWDERS
Pour the powder directly into the dispenser drawer. Do
not sprinkle powder onto clothes in the machine drum.
TRADITIONAL LIQUIDS
WHITES
Liquid can be placed in the main wash compartment of
the detergent drawer marked with the symbol
, start
the machine immediately upon placing the detergent in
the dispenser drawer.
Alternatively the detergent is measured into the
specially designed dosing device* which should be
placed on top of the laundry, and at the back of the
machine drum.
We recommend the Ariel product
range which is biological and
designed to provide excellent
cleaning and stain removal even
at low temperatures.
NON BIOLOGICAL
If you prefer to use a non
biological detergent, which does
not contain enzymes we
recommend Fairy. Fairy provides
good cleaning and stain removal.
COMPACT POWDERS AND LIQUIDS
Compact detergents (or concentrates as they are also
known) are available in liquid or powder form, and
generally require a smaller dosage. Follow the
manufacturer’s instructions to ensure the most
economical usage. Pour the detergent directly into the
dispenser drawer, or alternatively measure the detergent
into the specially designed dosing device* which
should be placed on top of the laundry, and at the back
of the machine drum.
COLOUREDS
For coloured items you should use a
detergent which is designed to clean
while maintaining the original colour.
Ariel Color does not contain bleach
and therefore helps to preserve
colours.
* If you use a dosing device in a washer dryer,
please ensure the dosing device/ball is removed
before carrying out a drying programme.
DELICATE ITEMS
FABRIC CONDITIONERS
When washing delicates such as
woollens, you should use a product
which is specially designed to care for
fine fabrics.
Dreft Automatic is suitable for
woollens and other delicates.
These are ideal for improving ‘softness’, and also
reduce static cling on synthetics and make ironing
easier. They are available in two types:
For example Lenor liquid fabric
softener, for use in the washing
machine/washer dryer. The
liquid fabric softener should be
poured into the compartment
marked with the symbol .
Follow the manufacturer’s dosage
instructions and never exceed the
MAX level.
LAUNDRY BLEACH
For additional stain removal you may
wish to use a product such as Ace
Gentle Bleach which is used in addition
to your chosen detergent. Ace is
suitable for all washable fabrics
including silks, woollens and coloureds.
Bounce conditioning sheets for use
in a tumble dryer. We recommend
the conditioning sheets are pinned
(using a safety pin) to an article
of laundry and placed in the
tumble dryer.
14
Wash Care Symbols
Wash care labels inside garments recommend how to launder your clothes with the best results. The care labelling
code is in line with care labelling used in the rest of Europe. The symbols used make it easy to select the correct
programme on your washing machine.
WASHING SYMBOL
WASH ACTION
95
Normal (Maximum)
White Cotton or Linen
without Special Finishes
60
Normal (Maximum)
Cotton, Linen or Viscose
without Special Finishes
Colourfast at 60°C.
50
Reduced (Medium)
Nylon, Polyester/Cotton, Viscose
with Special Finishes,
Cotton/Acrylic Mix.
40
Normal (Maximum)
Cotton, Linen or Viscose
Colourfast at 40°C but not 60°C.
40
Reduced (Medium)
Acrylics, Acetate, Triacetate, Wool
mixes, Polyester/wool blends.
40
Much Reduced (Minimum)
Hand wash only
FABRIC
Wool, wool mixtures, Silks
Do not machine wash
BLEACHING
Chlorine bleach may be used
IRONING
Hot iron
Cotton, Linen, Viscose
Warm iron
Polyester mixtures, Wool
Cool iron
Acrylic, Nylon, Polyester
DRY CLEANING
May be dry cleaned. Other letters and/or a bar beneath the circle will
indicate the required process to the dry cleaner.
TUMBLE DRYING
with high heat setting
with low heat setting
May be tumble dried
X
A cross through any symbol means «DO NOT»
Important Notes
fabric conditioner to avoid the conditioner entering the
machine prematurely.
When using liquid detergent and a prewash programme,
place the detergent into the correct compartment in the
dispenser drawer, after the prewash has finished.
For best results, always use the dispenser drawer for
dispensing detergents and liquid additives.
Once the dispenser has been filled, close it by pushing it
in gently. This is particularly important if you are using
15
Washing Programmes
Programmes for cotton and linen
Wash programme/
Washing symbol
WHITES
Degree of soil
and type of laundry
For heavy soiled cotton
items.
and synthetics
Programme
dial position
95
Description
Wash at 95°C
3 rinses
Long spin
Possible
options
Max. Progr.
time
load mins.
/
HALF LOAD
EASY IRON
SPIN
5 kg
165
5 kg
128
5 kg
118
5 kg
115
2 kg
110
/
WHITES
ECONOMY
COLOUREDS
ECONOMY
COLOUR
CARE
White cotton, for
example normally soiled
work garments, sheets,
household linen,
underwear, towels.
Non fast coloured
cotton or linen fabrics,
normally soiled, shirts,
blouses, underwear.
Lightly soiled non-fast
coulored cotton items
60E(*)
Wash at 60 °C
3 rinses
Long spin
HALF LOAD
EASY IRON
SPIN
/
E40
Wash at 40 °C
3 rinses
Long spin
HALF LOAD
EASY IRON
SPIN
/
30
Wash at 30 °C
3 rinses
Long spin
/
HALF LOAD
EASY IRON
SPIN
/
SYNTHETICS
O
Synthetic or mixed
fabrics, underwear,
coloured garments,
non-shrink shirts,
blouses.
60-4030
Wash at 60°-40°30 °C
3 rinses
Short spin
/
EASY IRON
SPIN
/
For cancelling the wash
programme which is
running and for
switching the machine
off
(*)This programme is the reference programme for the Energy label according to EEC Directive 92/75.
The programme times are intended as a guide only. The actual time will vary depending on incoming water
temperature and pressure.
16
Washing Programmes
Programmes for delicates
Wash programme/
Washing symbol
DELICATES
HANDWASH
WOOL
+
WOOL COLD
, handwash
Degree of soil
and type of laundry
Delicate fabrics, for
example curtains
Programme
dial position
and Miniprogram
Description
Wash at 40 °C
3 rinses
Short spin
40
Wash at 30 °C
3 rinses
Short spin
Special programme for
hand washing fabrics
Specially tested
programme for wool
garments bearing the
“Pure new wool, nonshrink, machine
washable” label.
wool
Wash at 40 °C3 rinses
Short spin
40-
Special short
programme for lightly
MINIPROGRAM
soiled synthetic or
mixed fabrics
Wash at 30 °C
2 rinses
Short spin
Separate rinse cycle for
hand washed items of
all fabric
3 rinses
Short spin
SPIN
Separate spin for
all fabric
Long or short spin
(see page 8)
DRAIN
For emptying out the
last rinse water in
programmes with the
Rinse Hold
option.
Draining of water
RINSES
O
For cancelling the wash
programme which is
running and for
switching the machine
off
17
Possible
options
Max.
load
Progr.
time
mins.
2 kg
75
1 kg
60
1 kg
55
2 kg
30
5 kg
30
5 kg
4
-
1,5
/
SPIN
/
SPIN
/
SPIN
/
SPIN
/
EASY IRON
SPIN
/
SPIN
Maintenance and Cleaning
Before any maintenance or cleaning is carried out you
must DISCONNECT the appliance from the electricity
supply.
Descaling
The water we use normally contains lime. It is a good
idea to periodically use a water softening powder in the
machine. Do this separately from any laundry washing,
and according to the softening powder manufacturer's
instructions. This will help to prevent the formation of
lime deposits.
C0072
C0073
Cleaning the drawer recess
Having removed the drawer, use a small brush to clean
the recess, ensuring that all washing powder residue is
removed from the upper and lower part of the recess.
Replace the drawer and run the rinse programme
without any clothes in the drum.
After each wash
Leave the door open for a while. This helps to prevent
mould and stagnant smells forming inside the appliance.
Keeping the door open after a wash will also help to
preserve the door seal.
Maintenance Wash
With the use of low temperature washes it is possible to
get a build up of residues inside the drum.
We recommend that a maintenance wash be performed
on a regular basis.
To run a maintenance wash:
● The drum should be empty of laundry.
● Select the hottest cotton wash programme.
● Use a normal measure of detergent, must be a
powder (such as Ariel Futur).
P0038
Cleaning the pump
The pump should be inspected if
• the machine does not empty and/or spin
• the machine makes an unusual noise during draining
due to objects such as safety pins, coins etc. blocking
the pump.
Proceed as follows:
• Disconnect the appliance.
• If necessary wait until the water has cooled down.
• Open the pump door.
External cleaning
Clean the exterior cabinet of the appliance with mild
washing up liquid and water only, and then dry
thoroughly.
Cleaning the dispenser drawer
The washing powder and additive dispenser drawer
should be cleaned regularly.
Remove the drawer by pressing the catch downwards
and by pulling it out. Flush it out under a tap, to remove
any traces of accumulated powder.
To aid cleaning, the top part of the additive
compartment should be removed.
P1114
• Place a container close to the pump to collect any
spillage.
• Pull out the emergency emptying hose, place it in the
container and remove its cap.
• When no more water comes out, unscrew the pump
18
cover and remove it. Always keep a rag nearby to dry
up spillage of water when removing the cover.
Clean the filter using a hard bristle brush.
Tighten up the inlet hose.
P1115
P1090
• Remove any objects from the pump impeller by
The dangers of freezing
rotating it.
If the machine is exposed to temperatures below 0°C,
certain precautions should be taken.
● Turn off the water tap.
● Unscrew the inlet hose.
● Place the end of the emergency emptying hose and
that of the inlet hose in a bowl placed on the floor
and let water drain out.
● Screw the water inlet hose back on and reposition
the emergency emptying hose after having put the
cap on again.
● When you intend to start the machine again, make
sure that the room temperature is above 0°C.
• Put the cap back on the emergency emptying hose and
place the latter back in its seat.
Important!
Every time you drain the water through the emergency
emptying hose you must pour 2 litres of water into the
main wash compartment of the detergent drawer and
then run the drain programme. This will activate the
ECO valve and avoid the detergent remains being
wasted.
P1117
• Screw the pump cover fully in.
• Close the pump door.
Emergency emptying out
Warning
If the water is not discharged, proceed as follows to
empty out the machine:
• pull out the plug from the power socket;
• close the water tap;
• if necessary, wait until the water has cooled down;
• open the pump door;
• place a bowl on the floor and place the end of the
emergency emptying hose into the bowl. Remove its
cap. The water should drain by gravity into the bowl.
When the bowl is full, put the cap back on the hose.
Empty the bowl. Repeat the procedure until water
stops flowing out;
• clean the pump if necessary as previously described;
• replace the emergency emptying hose in its seat after
having plugged it;
• screw the pump cover again and close the door.
When the appliance is in use and depending on the
programme selected there can be hot water in the pump.
Never remove the pump cover during a wash cycle,
always wait until the appliance has finished the cycle,
and is empty. When replacing the cover, ensure it is
securely retightened so as to stop leaks and young
children being able to remove it.
Cleaning the water inlet filter
If your water is very hard or contains traces of lime
deposit, the water inlet filter may become clogged.
It is therefore a good idea to clean it from time to time.
Turn off the water tap. Unscrew the water inlet hose.
19
Something Not Working
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out
an engineer. Before contacting your local Service Force Centre, please carry out the checks listed below.
During machine operation it is possible that the END light flashes to indicate that the machine is not working. (In the
model ZWF 1420 W an acoustic signal can also be heard.)
• 4 flashes = door open
• 2 flashes = the water is not drained
• 1 flash = there is no water filling
Once the problem has been eliminated, press the START/PAUSE button to restart the programme. If after all checks,
the problem persists, contact your local Service Centre.
IMPORTANT: if you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or
installation, a charge will be made even if the appliance is under guarantee.
Symptom
The machine does not start
Possible causes
●
●
●
●
●
●
The machine does not fill
●
●
●
●
The machine fills then empties
immediately
●
●
●
The machine does not empty and/or
does not spin
●
●
●
●
●
●
There is water on the floor
●
●
●
●
●
Unsatisfactory washing results
●
●
●
●
The door has not been closed.
The plug is not properly inserted in the power socket.
There is no supply at the socket
The main fuse or the fuse in the plug has blown.
The selector dial is not correctly positioned and the START/PAUSE
button has not been depressed.
The delay start has been selected.
Ensure the water tap is open.
The filter in the inlet hose is blocked.
The inlet hose may be squashed or kinked.
The door has not been closed.
The end of the drain hose is too low.
The end of the drain hose is submerged in water.
There is no vent in the end of the drain hose.
The drain hose may be squashed or kinked.
The option
or
has been selected.
The drain pump may be blocked.
The drain hose extension, if fitted, is not correct. Follow the
instructions for connecting to the waste.
The drainage system pipes are blocked.
The wash load is unbalanced: redistribute the clothes inside the drum to
allow the machine to spin.
Too much detergent or unsuitable detergent has been used (creates too
much foam).
Check whether there are any leaks from one of the inlet hose fittings. It
is not always easy to see this as the water runs down the hose; check to
see if it is damp.
The drain hose may be damaged or not securely positioned.
The detergent dispenser drawer or recess is clogged.
The drainage system pipes are blocked.
Too little detergent or unsuitable detergent has been used. An
insufficient amount of detergent leaves the laundry looking grey and
causes lime scale to form.
Stubborn stains have not been treated prior to washing
The correct wash programme has not been selected.
Too much laundry has been placed in the drum.
20
Symptom
Possible causes
The machine vibrates when spinning
●
●
●
●
●
The door will not open
●
●
●
The internal packing has not been removed.
The machine is in contact with the wall or furniture.
The machine is not stable and level (check diagonally).
The washing load is badly distributed in the drum.
Maybe there is very little laundry in the drum.
The programme is still running.
The door lock has not yet released.
Water in the tub: the door cannot be opened if water is present in the
tub.
Spinning starts late or the machine
does not spin
●
The electronic unbalance detection device has cut in because the
laundry is not evenly distributed in the drum. The laundry is
redistributed by reverse rotation of the drum. This may happen several
times before the unbalance disappears and normal spinning can resume.
If, after 20 minutes, the laundry is still not evenly distributed in the
drum, the machine will not spin. In this case, redistribute the load
manually and reselect the spin programme.
The machine makes an unusual
noise
●
The machine is fitted with a type of motor which makes an unusual
noise compared with other traditional motors. This new motor ensures
a softer start and more even distribution of the laundry in the drum
when spinning, as well as increased stability of the machine.
No water is visible in the drum
●
Machines based on modern technology operate very economically
using very little water without affecting performance.
Before calling out an engineer, please ensure you have
read the details under the heading “Something Not
Working”.
When you contact the Service Force Centre you will
need to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of fault
4. The model and serial number of the appliance (found
on the rating plate - see picture)
5. The purchase date.
Service & Spare Parts
In the event of your appliance requiring service, or if
you wish to purchase spare parts, please contact your
local Service Force Centre by telephoning:
0870 5 929929
Your telephone call will be automatically routed to the
Service Force Centre covering your post code area.
For the address of your local Service Force Centre and
further information about Service Force, please visit the
website at www.serviceforce.co.uk.
For Customer Service in Ireland please contact us at the
address below:
Zanussi Electrolux
Electrolux Group (Irl) Ltd
Long Mile Road
Dublin 12
Republic of Ireland
Please note that a valid purchase receipt or
guarantee documentation is required for inguarantee service calls.
.
Ser
. No
. .....
....
Mo
Pro d. .....
d.
No .....
. .....
.....
Tel: +353 (0)1 4090751
Email: service.eid@electrolux.ie
Mod. ..........
Prod. No. ...........
P0042 BD
21
Ser. No. .........
Customer Care Department
Customer Care Department
Zanussi Electrolux
55-77 High Street
Slough
Berkshire
SL1 1DZ
Tel 08705 727727*
For general enquiries concerning your Zanussi
Electrolux appliance or for further information on
Zanussi Electrolux products, please contact our
Customer Care Department by letter or telephone at the
address below or visit our website at www.zanussi.co.uk
* calls to this number may be recorded for training
purposes.
Guarantee Conditions
Standard guarantee conditions
●
We, Zanussi Electrolux, undertake that if, within 12
months of the date of the purchase, this ZANUSSI
ELECTROLUX appliance or any part thereof is proved
to be defective by reason only of faulty workmanship or
materials, we will, at our option repair or replace the
same FREE OF ANY CHARGE for labour, materials or
carriage on condition that:
● The appliance has been correctly installed and used
only on the electricity supply stated on the rating
plate.
● The appliance has been used for normal domestic
purposes only, and in accordance with the
manufacturer’s instructions.
● The appliance has not been serviced, maintained,
repaired, taken apart or tampered with, by any
person not authorised by us.
● All service work under this guarantee must be
undertaken by a Service Force Centre.
● Any appliance or defective part replaced shall
become the Company’s property.
● This guarantee is in addition to your statutory and
other legal rights.
Home visits are made between 8.30am and 5.30pm
Monday to Friday. Visits may be available outside these
hours in which case a premium will be charged.
●
European guarantee
If you should move to another country within Europe
then your guarantee moves with you to your new home
subject to the following qualifications:
● The guarantee starts from the date you first
purchased your product.
● The guarantee is for the same period and to the same
extent for labour and parts as exists in the new
country of use for this brand or range of products.
● The guarantee relates to you and cannot be
transferred to another user.
● Your new home is within the European Community
(EC) or European Free Trade Area.
● The product is installed and used in accordance with
our instructions and is only used domestically, i.e. a
normal household.
● The product is installed taking into account
regulations in your new country.
Before you move please contact your nearest Customer
Care Centre, listed below, to give them details of your
new home. They will then ensure that the local Service
Organisation is aware of your move and able to look
after you and your appliances.
France
Senlis
+33 (0) 344 62 29 29
Germany
Nurnberg
+49 (0) 800 234 7378
Italy
Pordenone
+39 0434 39 4700
Sweden
Stockholm
+46 (0) 8 672 53 90
UK
Slough
+44 (0) 1753 219897
Ireland
Dublin
+353 (0) 1 4090751
Exclusions
This guarantee does not cover:
●
●
Appliances found to be in use within a commercial
environment, plus those which are subject to rental
agreements.
Products of Zanussi Electrolux manufacture which
are NOT marketed by Zanussi Electrolux.
Damage or calls resulting from transportation,
improper use or neglect, the replacement of any light
bulbs or removable parts of glass or plastic.
Costs incurred for calls to put right an appliance
which is improperly installed or calls to appliances
outside the United Kingdom.
22
Installation Instructions
It is dangerous to alter the specifications or
attempt to modify this product in any way.
Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
Any plumbing work required to install this
appliance should be carried out by a qualified
plumber or competent person.
Should the appliance power supply cable need to
be replaced, this should be carried out by our
Service Force Centre.
Technical Specifications
DIMENSIONS
Height
Width
Depth
85 cm
60 cm
59 cm
POWER SUPPLY VOLTAGE
TOTAL POWER ABSORBED
WATER PRESSURE
230-240 V/50 Hz
2050 W (10 A)
Minimum
Maximum
MAX LOAD CAPACITY
Cotton, linen
Synthetics
Delicate fabrics
Wool and handwash
SPIN SPEED
Maximum
CONSUMPTION DATA FOR WASHING
5 KG NORMALLY SOILED COTTON
ITEMS AT 60°C (PROGR. 60E)
Energy
Water
800 kP888888888
50 kPa (0.5 bar)
800 kPa (8.0 bar)
5.0 kg
2 kg
2 kg
1.0 kg
1000 rpm (ZWF 1020 W)
1200 rpm (ZWF 1220 W - S)
1400 rpm (ZWF 1420 W)
This appliance complies with the following E.E.C. Directives:
- 73/23 EEC of 19.2.73 (Low Voltage Directive) and subsequent modifications;
- 89/336 EEC of 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications.
23
0.95 kWh
49 litres
Unpacking
Positioning
Install the machine on a flat hard floor.
Make sure that air circulation around the machine is not
impeded by carpets, rugs etc. Check that the machine
does not touch the wall or other kitchen units.
Never place cardboard, wood or similar materials under
the machine to compensate for any unevenness in the
floor.
Your new washing machine has been designed to be
permanently plumbed in to your home’s water supply
and drainage system. However, if this is not possible, it
may be connected to suitable existing tap with the drain
hose discharging into a sink.
The appliance has one inlet hose, with female 3/4” BSP
thread connector. If this connection is not compatible
with the plumbing of the existing installation, a variety
of connectors are available from good hardware stores
and plumbers merchants to suit most domestic
plumbing. Any alteration to your existing plumbing
must be carried out by a competent person, or qualified
plumber.
All transit bolts and packing must be removed
before using the appliance.
Using a spanner unscrew and remove the rear right bolt.
Lay the machine gently on its back, making sure that the
hoses are not squashed.
P0255
Remove the polystyrene block from the bottom of the
machine.
Carefully slide out the right polythene bag (1).
Repeat the operation for the left polythene bag (2).
Installation on a Suspended Floor
2
P1068
Suspended wooden floors are particularly susceptible to
vibration. To help prevent vibration we recommend you
place a waterproof wood panel, at least 15 mm thick
under the appliance, secured to at least 2 floor beams
with screws. If possible install the appliance in one of
the corners of the room, where the floor is more stable.
1
P1066
Remove the polystyrene base.
Set the machine upright and remove the two remaining
bolts from the back.
Pull out the three plastic spacers from the holes into
which the bolts were fitted.
Plug all the holes with the plugs which you can find in
the envelope containing the instruction booklet.
Water inlet
Connect the hose to a tap with a 3/4” thread.
Do not use previously used hoses for water connection.
P1088
P0256
Installation should comply with local water authority
and building regulations’ requirements.
The appliance must be connected to a cold water
supply.
A minimum water pressure of 50 kPa (0.5 bar) is
required for safe operation of the appliance.
P0020
Important !
You are advised to keep all the packaging for re-use in
case the machine is to be transported again.
In case of moving the same precautions as per
paragraph “The dangers of freezing” must be taken i.e.
the residual water in the hoses must be pumped out.
24
The upright standpipe should have a minimum length of
30cm (12'') from the bottom of the elbow to the top of
the pipe (see diagram).
If you cannot make the cold water connection direct
from the rising mains, you may be able to operate the
appliance from your cold water storage system.
There should be a minimum distance of 5.02m
(16.5 ft) between the appliance’s inlet and the bottom of
the water storage tank.
Set the hose correctly by loosening the ring nut. After
positioning the inlet hose, be sure to tighten the ring nut
again to prevent leaks.
Min.60 cm.
(23.6")
Max. 90 cm.
(35.4")
3 pin
P1130
Make sure that it is designed in such a way, that the end
of the drain hose cannot be covered with water.
The drain hose may be extended to a maximum of 4
metres. An additional drain hose and joining piece
is available from your local Service Force Centre.
The joining piece must have an internal diameter of
18mm.
If you intend the drain hose to empty into a sink, make
sure that the sink is empty and the plug hole is not
blocked. Use the plastic “U-Piece” supplied.
P0021
Water drainage
This appliance is designed to be permanently plumbed
into your home's water supply and drainage system.
The appliance drain hose should hook into a standpipe,
the hook in the drain hose is formed using the plastic
“U-Piece” supplied.
30 cm (12")
38 mm (11.2”)
standpipe
diameter
P0022
The drain hose must not be kinked.
Important
●
The standpipe should have an internal diameter of
approximately 38mm (see diagram) thus ensuring there
is an air break between the drain hose and standpipe.
Min. 30 cm.(12")
●
38 mm.(1/1 2") diameter
standpipe
P1040
When discharging into a standpipe ensure that the top of
the curve in the hose end is no more than 90cm (35.4'')
and no less than 60cm (23.6'') above floor level.
25
Before connecting the machine to new pipework or
to pipework that has not been used for some time,
run off a reasonable amount of water to flush out any
debris that may have collected in the pipes.
For the correct functioning of the machine the drain
hose must be hooked on the proper support piece
situated on the top of the back side of the appliance.
Levelling
In the interest of the
environment
Level the washing machine by raising or lowering the
feet. The feet may be tight to adjust as they incorporate
a self locking nut, but the machine MUST be level and
stable.
Washing machines and dishwashers should be
connected to the FOUL drainage system, the water will
then be taken to a sewage works for treatment before
being discharged safely into a river.
It is essential that these appliances are not connected to
the surface water drainage system as this water is
discharged directly into a river or stream and may cause
pollution.
If you require any further advice please contact your
local water authority.
P1051
Any necessary adjustment can be made with a spanner.
Accurate levelling prevents vibration, noise and
displacement of the machine during operation.
Some vibration is inevitable, especially if mounted on a
wooden floor.
Sprung wooden floors are particularly susceptible to
vibration. For advice, consult a builder. If possible,
always place the machine on a solid floor.
SHOWER
SINK
TOILET
BATH
BIDET
Special conditions
If the floor is carpeted or covered with crumbly or soft
material, insert a rigid support base under the feet to
prevent noise, vibration or displacement. The base
should protrude a few centimetres beyond the edges of
the machine.
WASHING
MACHINE
DISHWASHER
RAINWATER
'RUN-OFF'
FOUL DRAIN
SURFACE WATER
DRAINS & SEWERS
Warning
The machine should NOT be placed on deep pile
carpeting.
UNTREATED
DISCHARGE
FOUL SEWERS
SEWAGE
TREATMENT
WORKS
TREATED
DISCHARGE
RIVER
P0987
Note
Please ensure that when the appliance is installed it is
easily accessible for the engineer in the event of a
breakdown.
26
RIVER
Electrical connection
The wire coloured brown must be connected to the
terminal marked «L» or coloured red.
Upon completion there must be no cut, or stray strands
of wire present and the cord clamp must be secure over
the outer sheath.
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
WARNING: THIS APPLIANCE MUST BE
EARTHED.
The manufacturer declines any liability should
this safety measure not be observed.
WARNING:
A cut off plug inserted into a 13 amp socket is
a serious safety (shock) hazard.
Ensure that the cut off plug is disposed of
safely.
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the appliance’s
rating plate. The rating plate is located at the bottom of
the rim of the open door.
Should the appliance power supply cable need to be
replaced, this must be carried out by our Service
Force Centre.
Mo
Pro d. .....
d.
No .....
. .....
.....
.
Ser
. No
. .....
....
Note
When the appliance is installed the power supply cable
must be accessible.
Permanent connection
Mod. ..........
Prod. No. ...........
Ser. No. .........
P0042 BD
In the case of permanent connection it is necessary that
you install a double pole switch between the appliance
and the electricity supply (mains), with a minimum gap
of 3mm between the switch contacts and of a type
suitable for the required load in compliance with the
current electrical regulations.
The switch must not break the yellow and green earth
cable at any point.
The appliance is supplied with a 13amp plug fitted.
In the event of having to change the fuse in the plug
supplied, a 13amp ASTA approved (BS1363A) fuse
must be used.
Should the plug need to be replaced for any reason,
proceed as described below.
The wires in the mains lead are coloured in accordance
with the following code:
Green and Yellow
- Earth
Blue
- Neutral
Brown
- Live
GREEN & YELLOW
13A
E
N
L
BROWN
BLUE
P1041
CORD CLAMP
The wire coloured green and yellow must be connected
to the terminal marked with the letter «E» or by the
earth symbol
or coloured green and yellow.
The wire coloured blue must be connected to the
terminal marked «N» or coloured black.
27
From the Electrolux Group. The world’s No. 1 choice.
The Electrolux Group is the world's largest producer of powered appliances for kitchen, cleaning and outdoor use.
More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum
cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150
countries around the world.
© Electrolux plc 2004