- Sports & recreation
- Fitness, gymnastics & weight training
- Treadmills
- Slazenger
- Track Motion
- Owner's manual
Slazenger Track Motion Owner Manual
Add to My manuals28 Pages
Slazenger Track Motion: Get ready to embark on a personalized fitness journey at home with this feature-rich treadmill. With a speed range of 0.5 to 14 km/h, it allows you to customize your workouts to suit your fitness level. Track your progress with the easy-to-read display that showcases speed, distance, and time. Stay motivated and entertained during your runs with the built-in 5 automatic speed variation modes. For added safety, the treadmill is equipped with a safety key and a sturdy frame that supports up to 130 kg.
advertisement
Slazenger Track Motion
Gebruikershandleiding
INHOUD
Ⅰ
Veiligheidsmaatregelen
Ⅱ
Installatie
Ⅲ
Bediening
Ⅳ
Dagelijks
onderhoud
Ⅴ
Lijst
van
onderdelen
in
het
pakket
Ⅵ
Probleemoplossing
Technische gegevens:
●
Snelheidsbereik: 0.5—1
4
(km/h)
●
Stroominvoer: 220V(50Hz)
●
Afstandsbereik: 00.0—99.9(km)
●
Tijdsbereik: 00:00 ‐‐ 99:59(min:sec)
●
Verbruik: 1
5
00W
●
Maximaal gebruikersgewicht: 130 kg
Ⅰ
Veiligheidsmaatregelen
Lees de instructies in de handleiding voor gebruik van de loopband.
De loopband moet opgeklapt en gezekerd zijn voor transport of optillen.
Raak de bevestiging niet aan tijdens transport.
Om letsel te voorkomen de loopband niet bij de armsteunen vast pakken tijdens het opklappen of laten zakken..
Laat kinderen en huisdieren niet bij de loopband tijdens gebruik.
Het is belangrijk voor gebruikers van 35 jaar en ouder met een medische geschiedenis om vooraf contact met de huisarts op te nemen.
Plaats de loopband binnen in een schone en stofvrije ruimte waar geen kans is dat er water over
heen komt.
Plaats de loopband op een vlakke ondergrond met voldoende ruimte er omheen.
Steek de stekker in een geaard stopcontact.
Draag geschikte kleding en schoeisel tijdens gebruik.
Nooit de machine starten als u op de band staat en houd de handsteunen vast tijdens gebruik.
Als u zich tijdens gebruik niet goed voelt druk op stop of trek het veiligheidskoord los.
De sensor voor de hartslag is geen precisie instrument maar geeft alleen een indicatie van uw hartslag, door allerhande redenen kan de waarde afwijken.
Hart patiënten kunnen beter niet zonder toezicht de loopband gebruiken.
Selecteer een snelheid die bij uw conditie past.
Overbelasting zal schade aan de loopband veroorzaken.
Overschrijd nooit het maximale gebruikersgewicht.
Stof kan het meten van de apparatuur beïnvloeden, houd de loopband dus stofvrij.
Raak nooit draaiende onderdelen aan.
Ⅱ
INSTALLATIE
Installatie Tips:
1 Om installatieproblemen te voorkomen dient u de bouten pas aan te draaien als de hele montage voltooid is
2 Verwijder de borgingsstrip pas na complete montage.
(1)
Montage van het frame:
1.
Schuif de 7 aderige kabel door de rechter paal 2.
Verbind de sensordraden tussen de console en zet deze vast op het frame met bouten m8 x 16.
en de palen.
armsteunen en zet deze vast aan de
3.
Zet het paneel vast met zelftappers M4×12.
4.
Plaats de verbindingsstang tussen de palen en
zet en
deze plastic vast
met kapjes.
bouten m8 x 50, vulring m8
Ⅲ
Bediening
( ‐ )
Een overzicht van het display:
Gebruik loopband:
1.
Voorbereiding voor bediening:
Zet de knop aan na het monteren.
Bevestig de veiligheidsclip aan uw kleding.
De display piept, en dan staan alle waarden op nul.
De loopband staat in standby ‐ modus.
2.
Normale bedieningsmodus
:
De loopband staat in standby ‐ modus.
Druk op de startknop, de loopband start met 0.5km/h.
3.
Tijdmodus:
Pas snelheid aan van
0.5
‐ 16km/h door op de snelheids knoppen te drukken.
Druk op stop ‐ knop voor pauze ‐ stand, druk 2 keer voor standby ‐ modus.
4.
Afstand modus
5.
Hartslaggestuurde snelheidsmodus:
6.
5 Verschillende automatische snelheidsafwisseling modus:
(3)
Hartslag:
Tijdens stand ‐ by of lage snelheid, leg uw handen op de sensors op de armsteunen en de hartslag verschijnt in het scherm.
Opklappen:
Waarschuwing: Let er op dat uw vingers niet tussen de armsteunen komen te zitten tijdens het in ‐ en uitklappen van de loopband.
Ⅳ
Dagelijks
onderhoud.
1.
Plank en loopband
●
Deze gemotoriseerde loopband is uitgerust meteen band met een lage wrijvingsweerstand.
De loopplank is uitgevoerd met een dubbel schokabsorberend systeem om het lopen comfortabeler te maken.
● Houd de loopband schoon, het kan de levensduur bevorderen, Maak de loopband schoon met zeepwater.
Gebruik zo weinig mogelijk water en zorg dat het niet onder de loopband of in het motorcompartiment komt.
2.
Smering.
De loopband dient periodiek gesmeerd te worden met een special smeermiddel.
De methode is als volgt:
(1) Haal de spanning van de band door het tegen de klok in draaien van de inbusbouten aan het einde van de band.
(2) Breng een paar druppels olie aan op de onderzijde van de banden verdeel deze zo
veel mogelijk.
(3) Breng de spanning terug op de band door de inbusbouten weer aan te draaien.
(4) Laat de band draaien, onbelast en op lage snelheid, waardoor de olie zich nog beter
verdeeld.
Voorbeeld:
Loopband wordt minder dan 3 uur in de week gebruikt, olie dan ieder half jaar.
Loopband wordt 3 tot 6 uur per week gebruikt, olie dan iedere 3 maanden.
Loopband werkt meer dan 6 uur per week, olie dan iedere maand.
Overdaad schaadt,maar periodiek olieën verlengt de levensduur aanzienlijk.
3.
Schoonmaken.
Stofzuig regelmatig om stof in het regelpaneel en op de sensoren te voorkomen.
4.
Weerstand.
De weerstand
tussen de band en de loopplank kan te groot worden door te weinig olieof te veel stof.
Dit kan schade aan de motor veroorzaken.
Dit kan men op de volgende manier controleren:
(1) Na uitschakelen van de stroom moet men de band met de hand of de voet kunnen draaien, zo niet , dan is de weerstand te hoog.
(2) Bij motorschade zal de zekering er uit gaan.
5.Afstellen
als de loopband scheef gelopen is.
Alle loopbanden zijn afgesteld voordat ze de fabriek verlaten.
Maar na een periode van gebruik kan de band losser komen te liggen door de volgende oorzaken:
(1) Loopband staat niet vlak.
(2) De loper gaat niet over het midden van de band.
(3) De kracht per voet is verschillend.
Als de oorzaak bij de gebruiker ligt kan normalerwijze door de band enkele minuten onbelast te laten draaien het probleem worden opgelost.
Zo niet dan kunnen we het oplossen als volgt:
We kunnen de loopband als volgt afstellen met de inbusbouten aan de voorzijde.
Als de band naar de linkerzijde is gelopen,draai de linkerbout met de klok mee of de rechterbout tegen de klok in als in afbeelding a.
Als de band naar rechts is gelopen, draai de linkerbout tegen de klok in of de rechterbout met de klok mee, als in afbeelding b.
Opgepast: niet meer dan een kwartslag ineens en dan een periode onbelast laten draaien, meestal is dat voldoende.
6.Afstellen
van losse band.
Alle banden zijn afgesteld voor ze de fabriek verlaten , maar na een periode van gebruik kunnen ze iets oprekken waardoor u tijdens het lopen het gevoel krijgt dat de band even stil blijft staan.
Wanneer u dit bemerkt kunt u de band iets strakker zetten door de bouten aan het einde van de band iets aan te
draaien, beide zijden gelijk.
Zorg dat u de band niet te strak zet want dit kan schade aan de motor en de lagers veroorzaken.
7.
Afstellen motor riem
Als de riem van de motor te los komt te liggen wat bemerkbaar is aan het slippen van de loopband tijdens gebruik kan dit als volgt worden verholpen.
de sensor van de motor de bevestigingsbouten van de motor
7
8
9
10
11
12
13
14
NO
1
2
3
4
5
6
De riem van de motor de afstelbout van de motor
3
4
De afstelstappen:
1
2
1.
2.
Los de
Draai
bevestigingsbouten de afstelbout iets
iets.
aan.
3.
Controleer de spanning.
4.
Wanneer goed ,zet alle bouten weer vast.
Ⅴ
Lijst van onderdelen.
omschrijving
Hoofdframe
Steunen
Console veiligheidsschakelaar
Boven paneel
Steunverbinder
Plastic kapjes
Specificatie
Siliconen Olie
Bout M8×16
Bout M8×50
Vulring 8 mm
Self ‐ tapping schroeven M4×12 gereedschap
UNIT
SET set stuk stuk set stuk stuks blad flesje stuks stuks stuks stuks set
6
2
2
6
1
2
1
1 hoeveelheid
1
1
1
1
1
1
Ⅵ
Problemen oplossen:
Probleem
Er is geen aanwijzing op display bij in of uitschakelen.
Mogelijke oorzaak
1.
De stekker zit er niet goed in.2
.Geen
stroom op stopcontact
Oplossing
1.controleer
stekker.2.
controleer de zekering
Het stopt na even gebruik en display werkt normaal.
Automatische systeembeveiliging werkt..
1.
Druk op stop en start opnieuw .
2 .Schakel
de stroom uit opnieuw
na en
probeer een
De band loopt normaal maar slipt als u er op stapt
Controleer of de band ‐ enspanning te los is
Zet de loopband iets strakker
minuut
De loopband werkt niet normaal, en piept terwijl de displays normaal weergeven
De ingangstroom is te laag
Wacht tot voltage weer goed is
Geen display of display werkt niet goed
Schakel de stroom uit en na enkele minuten weer in.
NR. Omschrijving Soort Aantal NR. Omschrijving Soort Aantal
1 Hoofdframe Stuk 1 Wiel Stuk 2
2 Beschermrand Set 1 13 Sensor Stuk 1
4 Eindkappen Set 1 Stuk 1
5 Linker paal Stuk 1 16 Bout M8 X 16 Stuk 10
6 Rechter paal Stuk 1 17
7 Verbindingsbuis Stuk 1 18
Bout M8 X 50
Ring
Stuk 2
Stuk 2
9 Plastic Kabel
10 Plastic 1 21 Kabel
Stuk 1
Stuk 1
TREADMILL
Owner’s Guide
CONTENTS
Ⅰ SAFETY PRECAUTIONS
⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯
1
Ⅱ INSTALLATION
⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯
2
Ⅲ OPERATION
⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯
3
Ⅳ DAILY MAINTENANCE
⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯
5
Ⅴ LIST OF ITEM IN THE PACKAGE
⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯
8
Ⅵ TROUBLESHOOTING
⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯
9
Ⅺ STRUCTURE DRAWING & LIST
⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯
10
APPENDIXⅠ
:
SBW COMPARISON TABLE
⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯
12
APPENDIXⅡ
:
OBESITY DEGREE /BMI COMPARISON TALBE
⋯⋯
14
TECHNICAL DATA
●
Speed range:0.5—1
4
(km/h)
●
Input Voltage:220V(50Hz)
●
Distance range:0.00—9.99(km)
●
Time range:00:00--99:59(min:sec)
●
Power:1
5
00W
●
Biggest supporting value:1
30
(kg)
Ⅰ SAFETY PRECAUTIONS
FRIENDLY REMIND: Due to technology development,if there are changes,all interpretation rights shall belong to our company.
WARNINGS:
●
Read all precautions and instructions in the manual before using the treadmill.
●
The treadmill must be folded and locked before moving or lifting .Do not touch the safety lock when you lift the treadmill. Lifting and moving the treadmill is strictly prohibited when it is unfolded or unlocked.
●
To aovid accidentlly injury,please do not touch the armrest with your fingers when opening and folding the main frame.
●
Keep children away from the treadmill at all times.Children or pets should be kept 3 meters away.
●
It is important for users over the age of 35 or with medical history to consult physician before beginning any exercise or using the treadmill.
●
Keep the treadmill indoors,away from moisture and dust.Do not put the treadmill in a garage or covered patio,or near the water.
●
Place the treadmill on a level surface with eight feet of clearance behind it and two feet on each side.
●
Ensure the power cord is plug into a grounded circuit.No other appliance should be on the same circuit.
●
Wear appropriate sportswear and shoes while using the treadmill.Bare feet is forbidden while using.
●
Never start the machine when you are standing on the running belt. Always hold the handrails while using the treadmill.
●
If you feel incompatible or uncomfortable while using, press STOP or pull out the SAFE-
TY KEY immediately.
●
The sensor of heart rate is not a medical device, a lot of reasons can be caused and measured inaccurately, it is only for reference to measure the result.
●
Heart disease patient should not use the treadmill alone or use the QuickSpeed function.
●
Select the speed according to your physical condition. Patient should use the treadmill under doctor’s advice.
●
Always remove the key and unplug the power cord when not in use.
●
Overloading will damage the treadmill.Never exceed the maximum user weight.
●
Sensors covered in dust will affect the accuracy of the reading.Wipe off the dust with a dry cloth when needed.
●
Never touch any moving part while using the treadmill.
●
Keep long hair tied-up when using to prevent accident.
—1—
Ⅱ INSTALLATION
Installation Tips:
(
1 In order to avoid installation error,do not tighten up all the bolts in each step before the whole treadmill assembled completely.
2 Loosen the fixed strip between the mainframe and the base fundation after assembled,then move it to the suitable position.
1
)
MAINFRAME ASSEMBLE STEPS:
1. Through the 7 core line into the right poling, then tighten the poling and the mainframe with panhead bolt with M8×16.
2. Connect the sensor lines between the console and the armrest,then,connect the ones between the console and the polings.
3. Connect the upper sheath with self-tapping bolts
M4×12.
4. Connect the polings and the transverse bracing with panhead bolt M8×50,wahser Φ 8 and plastic blocks.
(
2
) MULTIFUNCTIONAL
ASSEMBLE STEPS:
1. Connect the multifuncitonal bracket with bolts
M8×16.
—2—
2. Connect the underside of multifunctional bracket and main frame with M8×16.
3. Connect the multifunctional head of bracket and main frame with M8×16.
Ⅲ OPERATION
(1)
The parts name of console:
;04,+0:73(@>05+6>
+0:;(5*,+0:73(@>05+6>
:7,,++0:73(@>05+6>
4. Fix the massager on the fixed pipe with the bolts on it.
7<3:,+0:73(@>05+6>
796.*(3+0:73(@>05+6>
:;672,@
-(:;2,@ :,;2,@ :(-,;@2,@ :36>2,@
:;(9;2,@
:7,,++09,*;2,@
/(5+3,7<3:,:,5:69
.907;/,/(5+3,:*(5;,:;@6<97<3:,
—3—
(2
) Debugging guide:
1
、
Preparation for operation:
Turn on the switch after installation
Keep safety key clip clothes your
The meter has a moo, then all display data is zero
2 Normal operation mode
X
The machine in Standby mode
Press start key, the treadmill start with
0.5km/h
3
\
Count down running mode
X
Press set key in standby state
Press fast or slow key set time
A djust speed
0.5-12km/h through press fast and slow speed key
Press start key, the treadmill start with
0.5km/h
4
\
Distance running mode:
Press two times set key in standby state
Press fast or slow key set distance
Press start key,
the treadmill start with 0.5km/h
5
\
Pulse control speed mode:
Press three times set key in standby state
Pulse control speed initial date is 100,speed is
2.8km/h
Press fast or slow key to set pulse
50-160/min
6
\
5 Kinds aut omatic variable speed mode
:
Press set key to choose P1-P5 speed programs
P ress start key, speed change every 200m
The machine in standby mode
Press stop key in pause state, press two times into standby state
Adjust speed
0.5-12km/h through press fast and slow speed key or quick
Press START key to start pulse control speed,0.5-6kn/h
It stop automaticall y after 2km
Press stop key in pause state, press two times into standby state
Adjust speed
0.5-12km/h through press fast and slow speed key or quick speed key
Press stop key in pause state, press two times into standby state
Press STOP key to pause,Press twice to stop
Press stop key in pause state, press two times into standby state
—4—
(
三
) Pulse test:
When in standby or low speed state,grip the handle pulse sensor on the armrest with two hands,we can test the user’s pulse by this methods.
(
四
)Operation on folding:
Warning:When folding or opening the machine,please do not touch the armrest with your fingers to avoid accidentally injury.
When folding the mainframe ,grip the waling piece in the back of the mainframe,uplift it until the locking apparatus locks automatically.
(Make sure that it is locked.)
On the condition of folding,the mainframe will land slowly under the function of the hydro cylinder if you spurn the locking apparatus.
Ⅳ DAILY MAINTENANCE
1. Running board and running belt
●
Brief:
The motorized treadmill use imported running belt, it’s with lower friction coefficient, higher intensity of tension, the running board is specially with double shock absorption system, its special smoothness and abrasion prevention make the movement more comfortable and fluent .
●
Clean
Keep cleanness of treadmill, it can prolong treadmill’s life, please usually clean the exposed running board both side of the running belt and foot board. Reduce the accumulation of the dust and trash under the running belt. Clean the running belt by dipped soap water; please note not to let water flow into machine and under the running belt.
—5—
2. Lubricating
The running board/belt must be lubricated by special lubrication after a period of use.
The methods and steps are in the following:(You’d better do it under the instruction of the professional person)
(1) Loosen the adjusting bolts of the back adjust ware on the both sides by inner hexagon spanner. Make the running belt loose.
(2) Slime the lubricant on the sport zone of the running board homogeneously.
(3) Adjust the running belt refer to the‘ adjust slanted running belt ’as a reference.
(4) Let the treadmill works for some time in a low speed after adjusting the running belts.
Make sure that the running belt is unbiassed.
Suggestion:
Treadmill works less than 3 hours every week. It’s lubricated one time every half of year.
Treadmill works from 3 to 6 hours every week. It’s lubricated one time every 3 months.
Treadmill works more than 6 hours every week. It’s lubricated one time every month.
Superfluous lubrication is not ok, it’s not good with more lubrication.
Please remember: reasonable lubricating is an important factor for prolonging treadmill’s life!
3. Clean
Please eliminate the dust regularly after a period of use, to keep the power panel and the head of the sensor clean.
4. Evaluation of friction
The friction between running belt and board will be increased as dust or reduced lubrication, this perhaps can harm motor, controller increased friction is with following character:
(1) When shut off power of treadmill, the running belt can’t be moved or it’s difficult for user to move by foot.
(2) Causing harm of motor of controller, open circuit and the fuse blows.
5.Adjust slanted running belt
All running belt are adjusted before the treadmill leaving the factory, but after after a period of time of using, the belt will become slanting, it may be caused by the following reasons:
(1) The engine frame is not steady.
(2) The user’s feet are not in the middle of the running belts when they are using it.
(3) The force on the feet is not even.
If the running belt is slanted by the user, it can return to normal after running without anyone for a few minutes.If the running belt can not return to normal by itself, we can adjust the
—6—
running belt regulator with the inner hexagon spanner
,
adjust it semicycle once. If the running belt is near the left side, adjust the left bolt clockwise or adjust the right bolt counter clockwise.(look at picture a)
If the running belt is near the right side, adjust the right bolt clockwise or adjust the left bolt counter clockwise.(look at picture b)
The running belt deflection is not in the insurance coverage,this problem can be maitained by the clients.The deflection can damage the running belt,so we must solve it in time when we find it.
6.Adjust flab or tight belt
All the running belts are adjusted brfore leaving the factory and after installation,but after a period of using, the running belt will become a little longer and give us some feeling of stopping when we are running. When this kind of phenomenon appears, adjust the running belt adjustable bolts clockwise and make the two sides equable, adjust them semicycle once.(look at picture c). If the running belt is loose,it is not in the insurance coverage,this problem can be maitained by the clients.If the running belt is too loose,it will appare skid phenomenon between the belt and the roller when we step on the belt.But it will be not good if the belt is too tight,it may damage the motor,belt and roller,and so on.
—7—
7. Adjust motor belt
All motor belts are adjusted before the treadmill leave the factory, but after a period of time of use, the belt will become flab and skid, this can be solved by the users.
The sensor of motor The fixing bolt of motor
The belt of motor The adjusting bolt of motor
The adjustment steps:
1.
2.
3.
4.
Loosen the screw of the motor.
Turn the adjustment screw in order with spanner.
Adjust it until the belt doesn’t slip.
After adjusting ,locking all the bolts.
Ⅴ LIST OF ITEM IN THE PACKAGE
㈠
Mainframe carton packling list:
10
11
12
13
8
9
6
7
14
4
5
2
3
NO
1
DESCRIPTION
Mainframe
Poling
Console
Safety Switch
Upper Sheath
Poling Transverse Bracing
Plastic Lump
Specification
Silicon Oil
Panhead Bolt M8×16
Panhead Bolt M8×50
Washerφ8
Self-tapping Screw M4×12
Special Purpose Tools
UNIT
SET
SUIT
PC
PC
SUITE
PC
PC
PC
PC
PC
PC
PAD
BOTTLE
SUIT
2
6
6
2
1
1
1
2
1
1
1
1
1
QUANTITY
1
—8—
㈡
Attachment carton packing list:
2
3
NO
1
DESCRIPTION
Support Lying Bracket(upper)
Support Lying Bracket(lower)
Massager
UNIT
PC
PC
SET
1
1
QUANTITY
1
Ⅵ TROUBLESHOOTING
:
Problems
There is no display when treadmill is turned on or off.
Possible Causes Solution
1. The power cord is not plugged well.
2 .The plug head is not inserted well.
3. The fuse is damaged..
1.Plug in again.
2. Connect it once more.
3. Change the fuse.
It stops by itself when using even.
All displays are normal.
The automatic system protection.
1. Press the ‘STOP’ key, then start it.
2 .Turn off the power switch, and start it in one minute.
The running belt is not working normal, and buzzes even all displays are normal.
The input voltage is too low.
The running belt runs normal by itself but disoriented when setpped on.
Check whether the running belt is too loose.
Use it when the voltage returns normal.
Adjusts the running belt accordingly.
No display or display not functioning properly.
The plug head not working because of external disturbance .
Turn off the power switch, then turn it on in one minute
●
Because of some reasons, the technical parameter may has a little difference. So we can not take it as criterion to measure our state of health, all the data is just as a reference.
●
Cut off the power immediately and call our customer service if you need further asistance. We will provide you the best service in time.
—9—
Ⅺ STRUCTURE DRAWING & LIST
(
一
)
NO.
DES
1 Mainframe
2 Side Rails Sets
3 Running belt
4 Rear End Cap Sets
5 Left Poling
6 Right Poling
7
Poling Transverse
Bracing
8 Console
9 Upper sheath
10 Plastic Lump
11 Foot screw
12 Moving Wheels
13 Sensor line Plug
1
1
1
1
1
1
1
4
2
1
1
1
2
Qty
PC
PC
PC
PC
SUITE
PC
UNIT
PC
SUITE
PC
SUIT
PC
PC
PC
NO.
DES
14 Sensor line Outlet
15 Motor cover
16 Panhead Bolt M8×16
17 Panhead Bolt M8×50
PC
PC
18 Washerφ8 PC
19 Self-tapping bolt M4×12 PC
PC
PC
UNIT
20 7 Core Line Plug
21 7 Core Line Outlet
22 Massager
23 Massager Belt
24
25
Support Lying
Bracket(lower)
Support Lying
Bracket(upper)
26 Bolt On The Massager
PC
PC
SET
PC
PC
PC
PC 3
1
1
1
1
1
1
1
2
6
11
2
Qty
1
—10—
(
二
NO.
DES
1 Mainframe
UNIT Qty
PC 1
2 Side Rails Sets SUITE 1
3
4
Running belt
Rear End Cap
Sets
5 Left Poling
PC
SUIT
PC
1
1
1
6 Right Poling
7
Poling
Transverse
Bracing
8 Console
9 Upper sheath
PC
PC
PC
SUITE
1
1
1
1
10 Plastic Lump
11 Foot screw
PC
PC
2
4
—11—
NO.
DES UNIT Qty
12 Moving Wheels PC 2
13 Sensor line Plug PC
14
Sensor line
Outlet
15 Motor cover
PC
PC
16
17
Panhead Bolt
M8×16
Panhead Bolt
M8×50
18 Washerφ8
19
Self-tapping bolt
M4×12
PC
PC
PC
PC
20 7 Core Line Plug PC
21
7 Core Line
Outlet
PC
1
1
1
10
2
2
6
1
1
APPENDIXⅠ
:
SBW COMPARISON TABLE
FEMALE SBW COMPARISON TABLE(UNIT:KG)
AGE
HEIGHT(CM)
152
55
57
59
61
47
49
51
53
63
65
67
69
39
41
43
45
33
35
37
19
21
23
25
27
29
31
53
53
53
53
52
52
52
53
52
52
52
52
50
51
51
52
48
49
49
46
46
46
46
47
47
48
156
54
55
55
54
53
53
54
54
54
54
54
54
52
52
53
53
50
50
51
47
47
47
48
48
49
49
160 162 164 166
56
56
56
56
57
56
56
56
55
55
55
55
53
54
55
55
51
52
53
49
49
49
49
50
51
51
57
57
57
56
57
56
56
56
56
56
56
56
53
54
55
55
52
52
53
50
50
50
50
51
52
52
58
58
58
57
57
57
57
58
57
57
57
57
55
55
56
57
53
53
54
51
51
51
51
52
53
53
60
60
60
59
58
59
59
59
59
59
59
59
57
57
58
58
55
55
56
52
52
52
53
53
54
54
168 170 172 176
61
61
61
61
60
60
61
61
61
61
61
61
59
59
60
60
57
57
59
54
54
54
55
55
56
56
63
63
63
63
62
62
62
62
62
62
62
62
650
61
62
62
58
59
60
56
56
56
56
56
58
58
64
64
64
64
63
63
63
64
63
63
63
63
61
62
63
63
59
60
61
57
57
57
57
58
59
59
67
68
68
67
67
67
67
67
67
66
66
66
65
65
66
66
63
63
64
60
60
60
61
61
62
62
—12—
MALE SBW COMPARISON TABLE(UNIT:KG)
AGE
HEIGHT(CM)
152
53
55
57
59
45
47
49
51
61
63
65
67
69
27
29
31
33
19
21
23
25
35
37
39
41
43
57
56
56
56
56
56
56
57
56
56
56
56
56
52
53
53
54
50
51
52
52
54
55
55
55
56
156
58
57
57
57
58
58
58
58
57
57
57
57
57
55
55
56
56
52
53
54
54
56
57
57
57
57
160 164 168 172
59
59
59
58
59
59
59
59
58
58
58
58
58
55
56
56
57
52
54
55
55
57
58
58
58
58
61
61
60
60
60
61
61
61
60
60
60
60
60
57
57
58
58
54
55
56
57
59
59
60
60
60
63
63
62
62
62
63
63
63
62
62
62
62
62
59
59
60
60
56
57
58
59
61
61
61
62
62
65
65
65
64
64
65
65
65
64
64
64
64
64
61
61
62
63
58
60
60
61
63
63
64
64
64
176 180 184 188
68
68
67
67
67
67
68
68
67
67
67
67
67
64
64
65
65
61
62
63
63
66
66
66
67
67
71
71
70
70
70
71
71
71
70
70
70
70
70
67
67
68
68
64
65
66
67
69
69
70
70
70
75
75
74
74
74
75
75
75
74
74
74
74
74
71
71
72
72
67
69
70
71
73
73
74
74
74
78
78
77
77
77
78
78
78
77
77
77
77
77
74
74
75
75
70
72
73
74
76
76
77
77
77
—13—
APPENDIX
Ⅱ
:
OBESITY DEGREE /BMI COMPARISON TALBE
BMI=WEIGHT(KG)/SQUARE OF HEIGHT
FAT DEGREE=(ACTUAL WEIGHT-STANDERD WEIGHT)÷STANDERD
WEIGHT×100%
BMI DATE
FAT DEGREE
WEIGHT DEGREE
WHO
STANDERD
ASIAN
STANDERD
CHINESE
STANDERD
THIN <20%
LOWER WEIGHT <10%~20%
NORMAL SCOPE
OVERWEIGHT
10%
﹥10%~20%
EARLY FAT
ⅠDEGREE FAT
ⅡDEGREE FAT
ⅢDEGREE FAT
﹥20%
<18.5
18.5~24.9
25.0
25.0~29.9
30.0~34.9
35.0~39.9
40.0
<18.5
18.5~2.9
23.0
23.0~24.9
25.0~29.9
30.0~39.9
40.0
<18.5
18.5~23.9
24.0
24.0~26.9
27.0~29.9
30.0~39.9
40.0
—14—
advertisement