Sharp PG-F211X - XGA DLP Projector Service manual

TopPage
PG-F211X/PG-F261X
SERVICE MANUAL
No. S57K1PG-F211X
MULTIMEDIA PROJECTOR
MODELS
PG-F211X
PG-F261X
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used.
OUTLINE
This Service Manual covers the differences from XG-F210X. For other technical information, refer to the XR-30S/
XR-30X/XG-F210X (No. S47E3XR-30XS/) Service Manual.
CONTENTS
OUTLINE AND MODIFIED PARTS LIST
OUTLINE.............................................................i
MODIFIED PARTS ..............................................i
CHAPTER 2. ELECTRICAL ADJUSTMENT
[1] ELECTRICAL ADJUSTMENT .......................2-1
[2] Adjustment mode process menu ...................2-4
SAFETY PRECAUTION
IMPORTANT SERVICE SAFETY
NOTES...............................................................ii
Precautions for using lead-free solder ............. vii
Parts Guide
CHAPTER 1. OPERATION MANUAL
[1] Specifications ................................................. 1-1
Parts marked with "
" are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the
safety and performance of the set.
This document has been published to be used for
after sales service only.
The contents are subject to change without notice.
PG-F211X/PG-F261X
PGF211X
OUTLINE AND MODIFIED PARTS LIST
Service Manual
OUTLINE
This Service Manual covers the differences from XG-F210X. For other technical information, refer to the XR-30S/XR-30X/XG-F210X (No. S47E3XR30XS/) Service Manual.
MODIFIED PARTS
(XG-F210X
→
PG-F211X/PG-F261X)
Ref.No.
Description
PRINTED WIRING BOARD ASSEMBLIES
BALLAST POWER Ass'y
BALLAST CONTROL
Unit
PHOTO SENSOR Unit
R/C RECEIVER Unit
XG-F210X
PG-F211X/PG-F261X
Note
DSETUE149FMG0
←
-
DUNTKE150WEF0
←
-
DUNTKE151WEF0
DUNTKE152WEF0
←
←
DUNTKE153FMF6 (PG-F211X)
DUNTKE153FMF7 (PG-F261X)
←
MAIN Unit
DUNTKE153FMF4 (XG-F210X)
DMD Unit
DUNTKE154WEF0
CABINET AND MECHANICAL PARTS : Please refer to a Parts Guide.
OPTICAL MECHANISM PARTS : Please refer to a Parts Guide.
SUPPLIED ACCESSORIES : Please refer to a Parts Guide.
PACKING PARTS AND ACCESSORIES : Please refer to a Parts Guide.
SERVICE JIGS AND EQUIPMENT(USE FOR SERVICING) : Please refer to a Parts Guide.
i
No parts changed
No parts changed
-
PG-F211X/PG-F261X
PGF211X
SAFETY PRECAUTION
Service Manual
IMPORTANT SERVICE SAFETY NOTES
IMPORTANT SERVICE SAFETY NOTES (for USA)
Service work should be performed only by qualified service technicians who are
thoroughly familiar with all safety checks and servicing guidelines as follows:
Use an AC voltmeter with sensitivity of 5000 ohm per
volt., or higher, sensitivity to measure the AC voltage
drop across the resistor.
All checks must be repeated with the AC plug
connection reversed. (If necessary, a non-polarized
adapter plug must be used only for the purpose of
completing these checks.)
Any reading of 0.4 volts RMS (this corresponds to 0.27
milliamp. AC.) or more is excessive and indicates a
potential shock hazard which must be corrected before
returning the unit to the owner.
WARNING
1. For continued safety, no modification of any circuit
should be attempted.
2. Disconnect AC power before servicing.
BEFORE RETURNING THE PROJECTOR:
(Fire & Shock Hazard)
Before returning the projector to the user, perform
the following safety checks:
1. Inspect lead wires are not pinched between the chassis
and other metal parts of the projector.
2. Inspect all protective devices such as non-metallic
control knobs, insulating materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacity networks, mechanical
insulators, etc.
3. To be sure that no shock hazard exists, check for
current leakage in the following manner:
Plug the AC cord directly into a 120 - volt AC outlet,
(Do not use an isolation transformer for this test).
Using two clip leads, connect a 1.5k ohm, 10 watt
resistor paralleled by a 0.15µF capacitor in parallel
between all exposed metal cabinet parts and earth
ground.
DVM
AC SCALE
1.5k ohm
10W
0.15 µF
TEST PROBE
TO EXPOSED
METAL PARTS
CONNECT TO
KNOWN EARTH
GROUND
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
SAFETY NOTICE
R
Many electrical and mechanical parts in DLP
Projector have special safety-related characteristics.
These characteristics are often not evident from visual
inspection, nor can protection afforded by them be
necessarily increased by using replacement components
rated for higher voltage, wattage, etc.
Replacement parts which have these special safety
characteristics are identified in this manual; electrical
components having such features are identified by “ ”
and shaded areas in the Replacement Parts Lists and
Schematic Diagrams. For continued protection,
replacement parts must be identical to those used in
the original circuit. The use of a substitute replacement
parts which do not have the same safety characteristics
as the factory recommended replacement parts shown
in this service manual, may create shock, fire or other
hazards.
WARNING: The bimetallic component has the primary
conductive side exposed. Be very careful in
handling this component when the power is on.
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
ii
PG-F211X/PG-F261X
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement
accoutumé à toute vérification de sécurité et aux conseils suivants.
AVERTISSEMENT
Utiliser un voltmètre CA d'une sensibilité d'au moins
5000Ω/V pour mesurer la chute de tension en travers
de la résistance.
Toucher avec la sonde d'essai les pièces métalliques
exposées qui présentent une voie de retour au châssis
(antenne, coffret métallique, tête des vis, arbres de
commande et des boutons, écusson, etc.) et mesurer la
chute de tension CA en-travers de la résistance. Toutes
les vérifications doivent être refaites après avoir inversé
la fiche du cordon d'alimentation. (Si nécessaire, une
prise d'adpatation non polarisée peut être utilisée dans
le but de terminer ces vérifications.)
La tension de pointe mesurèe ne doit pas dépasser 0.4V
(correspondante au courant CA de pointe de 0.27mA).
Dans le cas contraire, il y a une possibilité de choc
électrique qui doit être supprimée avant de rendre le
récepteur au client.
1. N'entreprendre aucune modification de tout circuit.
C'est dangereux.
2. Débrancher le récepteur avant toute réparation.
VERIFICATIONS CONTRE L'INCEN-DIE ET
LE CHOC ELECTRIQUE
Avant de rendre le récepteur à l'utilisateur, effectuer
les vérifications suivantes.
1. Inspecter tous les faisceaux de câbles pour s'assurer
que les fils ne soient pas pincés ou qu'un outil ne soit
pas placé entre le châssis et les autres pièces
métalliques du récepteur.
2. Inspecter tous les dispositifs de protection comme les
boutons de commande non-métalliques, les isolants, le
dos du coffret, les couvercles ou blindages de réglage
et de compartiment, les réseaux de résistance-capacité,
les isolateurs mécaniques, etc.
3. S'assurer qu'il n'y ait pas de danger d'électrocution en
vérifiant la fuite de courant, de la facon suivante:
Brancher le cordon d'alimentation directem-ent à une
prise de courant de 120 - V. (Ne pas utiliser de
transformateur d'isolation pour cet essai).
A l'aide de deux fils à pinces, brancher une résistance
de 1.5 kΩ 10 watts en parallèle avec un condensateur
de 0.15µF en série avec toutes les pièces métalliques
exposées du coffret et une terre connue comme une
conduite électrique ou une prise de terre branchée à la
terre.
DVM
ECHELLE CA
1.5k ohm
10W
0.15 µF
SONDE D'ESSAI
AUX PIECES
METALLIQUES
EXPOSEES
BRANCHER A UNE
TERRE CONNUE
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
AVIS POUR LA SECURITE
De nombreuses pièces, électriques et mécaniques, dans
les projecteur à DLP présentent des caractéristiques
spéciales relatives à la sécurité, qui ne sont souvent pas
évidentes à vue.
Le degré de protection ne peut pas être nécessairement
augmentée en utilisant des pièces de remplacement
étalonnées pour haute tension, puissance, etc.
Les pièces de remplacement qui présentent ces
caractéristiques sont identifiées dans ce manuel;
les pièces électriques qui présentent ces particularités
sont identifiées par la marque “ ” et hachurées dans la
R
liste des pièces de remplacement et les diagrammes
schématiques. Pour assurer la protection, ces pièces
doivent être identiques à celles utilisées dans le circuit
d’origine. L’utilisation de pièces qui n’ont pas les mêmes
caractéristiques que les pièces recommandées par l’usine,
indiquées dans ce manuel, peut provoquer des
électrocutions, incendies ou autres accidents.
AVERTISSEMENT: La composante bimétallique dispose du
conducteur primaire dénudé. Faire attention
lors de la manipulation de cette
composante sous tension.
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
iii
PG-F211X/PG-F261X
NOTE TO SERVICE
PERSONNEL
NOTE POUR LE PERSONNEL
D’ENTRETIEN
//////////////////////////////////////////////////////////////
UV-RADIATION PRECAUTION
//////////////////////////////////////////////////////////////
//////////////////////////////////////////////////////////////
PRECAUTION POUR LES RADIATIONS UV
//////////////////////////////////////////////////////////////
The light source, lamp, in the projector emits small
amounts of UV-Radiation.
La source de lumière, la lampe, dans le projecteur émet
de petites quantités de radiation UV.
AVOID DIRECT EYE AND SKIN EXPOSURE.
EVITEZ TOUTE EXPOSITION DIRECTE DES
YEUX ET DE LA PEAU.
To ensure safety please adhere to the following:
Pour votre sécurité, nous vous prions de respecter
les points suivants:
1. Toujours porter des lunettes de soleil lors d’un entretien
du projecteur
avec la lampe allumée
et le haut du coffret retiré.
1. Be sure to wear sun-glasses when servicing the
projector with the lamp
turned “on” and the top
enclosure removed.
2. Ne pas faire fonctionner la lampe à l’extérieur du boîtier
de lampe.
2. Do not operate the lamp outside of the lamp housing.
3. Ne pas faire fonctionner plus de 2 heures avec le coffret
retiré.
3. Do not operate for more than 2 hours with the enclosure
removed.
Précautions pour les radiations UV
et la lampe moyenne pression
UV-Radiation and Medium Pressure
Lamp Precautions
1. Toujours débrancher la fiche AC lors du remplacement
de la lampe.
2. Laisser l’unité refroidir pendant une heure avant de
procéder à l’entretien.
3. Ne remplacer qu’avec une lampe du même type. Type
AN-XR30LP, caractéristique 200W-DC.
4. La lampe émet de petites quantités de radiation UVéviter tout contact direct avec les yeux.
5. La lampe moyenne pression implique un risque
d’explosion. Toujours suivre les instructions
d’installation décrites ci-dessous et manipuler la lampe
avec soin.
1. Be sure to disconnect the AC plug when replacing the
lamp.
2. Allow one hour for the unit to cool down before
servicing.
3. Replace only with same type lamp. Type AN-XR30LP
rated 200W DC.
4. The lamp emits small amounts of UV-Radiation, avoid
direct-eye contact.
5. The medium pressure lamp involves a risk of explosion.
Be sure to follow installation instructions described
below and handle the lamp with care.
iv
PG-F211X/PG-F261X
//////////////////////////////////////////////////////////////// ////////////////////////////////////////////////////////////////
PRECAUTION POUR LES RADIA TIONS UV (Suite)
UV-RADIATION PRECAUTION (Continued)
//////////////////////////////////////////////////////////////// ////////////////////////////////////////////////////////////////
Lamp Replacement
Remplacement de la lampe
Note:
Remarque:
Since the lamp reaches a very high temperature during
units operation replacement of the lamp should be
done at least one hour after the power has been turned
off. (to allow the lamp to cool off.)
Installing the new lamp, make sure not to touch the
lamp (bulb) replace the lamp by holding its reflector
2 .
[Use original replacement only.]
Comme la lampe devient très chaude pendant le
fonctionnement de l’unité, son remplacement ne doit
être effectué au moins une heure après avoir coupé
l’alimentation (pour permettre à la lampe de refroidir).
En installant la nouvelle lampe, s’assurer de ne pas
toucher la lampe (ampoule). Remplacer la lampe en
tenant son réflecteur 2 .
[N’utiliser qu’un remplacement d’origine.]
1 Lampe
1 Lamp
2 Reflecteur
2 Reflector
DANGER ! –– Never turn the power on without the
lamp to avoid electric-shock or damage of the devices
since the stabilizer generates high voltages at its start.
DANGER ! –– Ne jamais mettre sous tension sans la
lampe pour éviter un choc électrique ou des
dommages des appareils car le stabilisateur génère
de hautes tensions à sa mise en route.
Since small amounts of UV-radiation are emitted
from an opening between the exhaust fans, it is recommended to place the cap of the optional lens on
the opening during servicing to avoid eye and skin
exposure.
Comme de petites quantités de radiation UV sont
émises par une ouverture entre les ventilateurs aspirants, il est recommandé de placer le capuchon de
l’optique optionnelle sur l’ouverture pendant l’entretien
pour éviter une exposition des yeux et la peau.
v
PG-F211X/PG-F261X
WARNING:
High brightness light source, do not stare into the beam of light, or view directly. Be especially
careful that children do not stare directly into the beam of light.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO
MOISTURE OR WET LOCATIONS.
CAUTION
The lighting flash with arrowhead within a
triangle is intended to tell the user that
parts inside the product are risk of electric
shock to persons.
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREW.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE CABINET.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The exclamation point within a triangle is
intended to tell the user that important
operating and servicing instructions are in
the manual with the projector.
CAUTION
(POWER Unit)
6.3A 250V
For continued
protection against a
risk of fire, replace
only with same type
6.3A, AC250V fuse.
(F701)
AVERTISSEMENT: Source lumineuse de grande intensité. Ne pas fixer le faisceau lumineux ou le regarder
directement. Veiller particulièrement à éviter que les enfants ne fixent directement le
faisceau lumineux.
AVERTISSEMENT: AFIN D’EVITER TOUT RISQUE D’INCENDIE OU D’ELECTROCUTION, NE PAS PLACER
CET APPAREIL DANS UN ENDROIT HUMIDE OU MOUILLE.
ATTENTION
L’éclair terminé d’une flèche à l’intérieur
d’un triangle indique à l’utilisateur que les
pi‘eces se trouvant dans l’appareil sont
susceptibles de provoquer une décharge
électrique.
RISQUE
D’ÉLECTROCUTION. NE
PASR ETIRER LES VIS Á
L’EXCEPTION DE LA VIS DE
REPARATION UTILISATEUR
SPECIFIEES
Le point d’exclamation à l’intérieur d’un
triangle indique à l’utilisateur que les
instructions de fonctionnement et
d’entretien sont détaillées dans les
documents fournis avec le projecteur.
ATTENTION: POUR EVITER TOUT RISQUE
D’ELECTROCUTION, NE PAS RETIRER LE CAPOT.
AUCUNE DES PIECES INTERIEURES N’EST REPARABLE
PAR L’UTILISATEUR, A L’EXCEPTION DE L’UNITE DE
LAMPE. POUR TOUTE REPARATION, S’ADRESSER A UN
TECHNICIEN D’ENTRETIEN QUALIFIE.
PRECAUTION
(Unité de PUTSSANCE)
Pour une protection
continue contre un
risques d’incendie, ne
remplacer qu’avec un
fusible 6.3A,AC250V
6.3A 250V du même type.
(F701)
vi
PG-F211X/PG-F261X
Precautions for using lead-free solder
„Employing lead-free solder
•
"PWBs" of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The
alphabetical character following LF shows the type of lead-free solder.
Example:
LFa
Indicates lead-free solder of tin, silver and copper.
„Using lead-free wire solder
•
When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead wire solder may cause damage or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40 °C, we recommend you to use a dedicated soldering
bit, if you are not familiar with how to obtain lead-free wire solder or soldering bit, contact our service station or service branch in your area.
„Soldering
•
As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 °C which is higher than the conventional lead solder by 40 °C, and as it has poor
solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may be
peeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the
steady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit as
required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
•
Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
Part No.
ZHNDAi123250E
ZHNDAi126500E
ZHNDAi12801KE
Description
J
J
J
φ0.3mm 250g(1roll)
φ0.6mm 500g(1roll)
φ1.0mm 1kg(1roll)
Code
BL
BK
BM
vii
PG-F211X/PG-F261X
CHAPTER 1. OPERATION MANUAL
PGF211X
Service Manual
[1] Specifications
Model
Display device
Resolution
Lens
Input terminal
Output terminal
Control, others
XG-F211X/PG-F261X
0.55" DLP Chip
XGA (1024 x 768)
F number
Zoom
Focus
DVI-I (Compatible with HDCP)
RGB/Component (mini D-sub 15 pin)
S-Video (mini DIN 4 pin)
Video (RCA)
Audio (ø3.5 mm stereo minijack)
Audio (RCA)
RGB/Component (mini D-sub 15 pin)
Audio (ø3.5 mm stereo minijack)
USB (Type B)
RS-232C (mini DIN 9 pin)
Speaker
Projection lamp
Rated voltage
Rated frequency
Input current
Power consumption (Standby)
Operation temperature
Cabinet
Dimensions (main body only)
Weight (approx.)
F 2.5 – 2.6
Manual, x 1.15 (f = 20.4 – 23.5 mm)
Manual
x1
x1
x1
x1
x1
x 1 (L/R)
x1
x1
x1
x1
2 W (Mono)
200 W
AC 100 – 240 V
50/60 Hz
2.9 A
283 W (4.3 W) with AC 100 V
270 W (4.4 W) with AC 240 V
41°F to 95°F (+5°C to +35°C)
Plastic
10 41/64" x 3 33/64" x 10 7/16"
(270 (W) x 89 (H) x 265 (D) mm)
6.4 lbs. (2.9 kg)
As a part of policy of continuous improvement, SHARP reserves the right to make design and
specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from
these values in individual units.
1–1
PG-F211X/PG-F261X
CHAPTER 2. ELECTRICAL ADJUSTMENTService
PGF211X
Manual
[1] ELECTRICAL ADJUSTMENT
No.
1
Adjusting point
EEPROM
initialization
Adjusting conditions
1. Turn on the power (with the lamp on) and
warm up the set for 15 minutes.
2
Model setting
3
Adjustment of CW index
(Process menu)
1. Select the following group and subject.
Group: CONFIRM
Subject: MODEL
1. Signal input: Send 256 STEP color bar.
XGA series (XGA60HZ),
2. Select the following group and subject.
Group: ADJUST CW/Auto KS
Subject: CW-INDEX.
Adjusting procedure
•Make the following settings.
Press S2551 to call the process mode and execute
"SS2" on SS menu.
1. Set as below.
PG-F211X : 6
PG-F261X : 7
1. The signal is input into computer 1.
2. Select the adjustment item and adjust the lamp gradation patterns of RGBW so that smooth patterns
without noise appear.
W
R
G
B
4
R/G/B contrast adjustment
(manual or automatic)
1. Select the following group and subjects.
Group : ADJUST
AD/DLP
Subject : R-CONT
G-CONT
B-CONT
(Process GAMMA interlock)
2. Amplitude level 96% (0.67Vpp) the signal
is input into computer 1.
XGA series (XGA60HZ)
5
RGB white balance adjustment
6
sRGB white balance adjustment
1. 50% gray pattern signal is input into computer 1.
XGA series (XGA60HZ)
2. Select the following group and subjects.
Group : ADJUST
AD/DLP
Subject : R-GAIN
G-GAIN
B-GAIN
1. 50% gray pattern signal is input into computer 1.
XGA series (XGA60HZ)
2. Select the following group and subjects.
Group : CONFIRM/DLP
Subject : S-G-OS
S-B-OS
1. Measure chromaticity of the 96% white wind pattern
using CA100.
2. On the screen where bit dropouts occur, raise the
values of R/G/B-Contrast. Adjust the values so that
bright red, green, and blue bit dropouts appear on
a black background; and amounts of change in x
value of R and y values of G/B become 100/1000
or more.
3. If adjustment is performed manually watching the
screen, make adjustment so that bright red, green,
and blue bit dropouts appear on more than half of
the screen.
1. Raise the values of two of R/G/B-GAIN (default:
100) so that the following chromaticity values are
obtained using CL200.
x value: 295 ± 5
y value: 310 ± 5
1. Adjust S-G-OS and S-B-OS so that the following
chromaticity values are obtained using CL200.
x value: 313 ± 5
y value: 329 ± 5
Check items
No.
1
Adjusting point
1 Adjustment of RGB brightness
Adjusting conditions
1. Select the following group and subjects.
Group : CONFIRM/AD
Subject : R-BRIGHT
G-BRIGHT
B-BRIGHT
(Process GAMMA interlock)
2–1
Adjusting procedure
1. Check the fixed value.
Fixed value : 127
PG-F211X/PG-F261X
No.
2
Adjusting point
Adjustment of Component offset
Adjusting conditions
1. Feed 10-step signal with 480P component
100% amplitude.
2. Select the following group and subjects.
Group : CONFIRM/AD
Subject : C-R-OS
C-B-OS
(Process GAMMA interlock)
1. Select the following group and subject.
Group : CONFIRM/DLP
Subject :R-BLK
G-BLK
B-BLK
(Process GAMMA interlock)
1. Feed NTSC 100% wind pattern signal.
(Signal with burst)
2. Select the following group and subjects.
Group : CONFIRM/VIDEO
Subject : V-CONT
1. Feed NTSC 100% wind pattern signal.
(Signal with burst)
2. Select the following group and subject.
Group : CONFIRM/VIDEO
Subject : V-BRIGHT
1. Feed split color bar.
2. Select the following group and subject.
Group : CONFIRM/VIDEO
Subject : V-HUE
1. Select the following group and subject.
Group : CONFIRM/VIDEO
Subject : V-COLOR
1. Feed the SMPTE pattern signal.
3
Adjustment of DLP Brightness
4
Video Contrast adjustment
5
Adjustment of Video Brightness
6
Adjustment of Video Tint
7
Adjustment of Video color saturation
8
RGB tone reproduction adjustment
9
VIDEO white balance adjustment
10
White balance checking and
readjustment
11
Off-timer performance
12
13
Thermistor performance checking 1. Heat the thermistor with a hair dryer.
Auto sync performance checking 1. Feed the phase check pattern signal.
14
DVI input operation check
Send the video signal to the DVI terminal.
15
Monitor out check
16
RS232C operation check
1. Send signals to COMPUTER 1 and COMPUTER 2.
2. Connect another monitor to the monitor
out.
3. Connect the audio OUT.
1. Connect the unit and a PC with the
RS232C cable.
1. Feed the 50% gray signal.
2. Select the following group and subjects.
Group :CONFIRM/VIDEO
Subject : V-R-OS
V-B-OS
1. RGB Input
sRGB Input
VIDEO Input
DTV Input
DVD Input
1. Select the following group and subjects.
Group :CONFIRM/CHECK
Subject : TEMP-OFF
2–2
Adjusting procedure
1. Check the fixed value.
C-R-OS : 257
C-B-OS : 257
1. Check the fixed value.
Fixed value : 256
1. Check the fixed value.
Fixed value : 124
1. Check the fixed value.
Fixed value : 68
1. Check the fixed value.
Fixed value : 128
1. Check the fixed value.
Fixed value : 154
1. Make sure the 100% and 95% white as well as the
0% and 5% black gradations are visible.
1. V-R-OS is 132.
V-B-OS is 132.
Check that there is no deviation of white balance with
the monitor.
1. Select OFF from the process mode.
Make sure the off-timer starts with 5 minutes
onscreen and count one minute in one second.
And then indication is 0 minute, the power supply of
the set is cut off.
1. Make sure that the temperature is indicated.
1. In the VGA, SVGA, XGA and SXGA modes, make
sure the Clock, Phase, H-Pos and V-Pos settings
can be automatically adjusted.
1. For PG-F211X/PG-F261X, check that an image is
properly projected through the digital input and analog input.
1. Check that the same images as seen on the screen
appear on the connected monitor and that the
sound from the sound source connected to the
audio OUT is heard.
1. Send a command from the PC, and check it functions correctly.
PG-F211X/PG-F261X
No.
17
Adjusting point
Model name and version check
Adjusting conditions
1. Select the following group.
Group : INFO/VERSION.
18
Setup guide screen check
19
Delivery settings
1. Turn on the power after making the setup
guide display ON setting or factory setting
(SS4, etc.).
1. Make the following settings.
Destination
USA
*
Process
adjustment
SS4
Adjusting procedure
1. The model name appears in the MODEL field, and
the firmware version in the VERSION field. Check
that they are correct.
1. Check that the 4-split screen is displayed correctly
and the display contents are correct.
Remote control
adjustment
Factory setting at 4
Writing a software program (before main PWB is mounted)
Use the DLP Composer Lite Ver. 4.2 to download the firmware.
After writing the specified version of firmware to the PWB using the RS232C cable, check the version of the written firmware.
If no software program is written, all three LEDs light up in the chassis inspection process.
Calling and quitting the process mode with the control keys on this model.
*
Although it is possible for the process OUT to exit using the process menu, the IN/OUT toggle command is also available considering the existing
specification.
1) Calling and quitting
With the menu not displayed, press the "ENTER", "ENTER", "VOL+", "VOL-", "ENTER", "ENTER" and "MENU" keys on the remote control or on
the main unit.
2) Others
Press the S2551 process key (toggle) on the main PWB to call and quit the process menu.
NOTE: When adjusting in the process mode, set a signal with a vertical frequency of 60 Hz or no signal. (May not be properly adjusted with other signals.)
Resetting the lamp timer for this model
1) Resetting procedure
In Stand-by, run this command to clear the operating time of the lamp to 0 and turn on the power.
Press and hold "
", "ENTER", and "MENU", and then press the "STANDBY/ON" key of the set.
Forced disabling of the System-Lock of this model
1) Disabling procedure
With System-Lock input window onscreen, press the "MENU", "ENTER", "ENTER", "MENU", "ENTER", "ENTER" and "MENU" keys, in this order,
on the remote controller.
2–3
PG-F211X/PG-F261X
[2] Adjustment mode process menu
1st Layer
ADJUST
CW/Auto KS
AD/DLP
SS
CONFIRM
AD
DLP
VIDEO
MODEL
CHECK
INFO
VERSION
PATTERN
LAMP
TEMP/FAN
2nd Layer
CW-INDEX
CAL
K-SENS
R-CONT
G-CONT
B-CONT
R-GAIN
G-GAIN
B-GAIN
SS1
SS2
SS3
SS4
SS5
SS6
R-BRIGHT
G-BRIGHT
B-BRIGHT
C-R-OS
C-B-OS
R-BLK
G-BLK
B-BLK
S-R-OS
S-G-OS
S-B-OS
V-CONT
V-BRIGHT
V-COLOR
V-HUE
V-R-OS
V-G-OS
V-B-OS
OFFSET-MODE
OFFSET-CONT
OFFSET-BRI
MODEL-SELECT
LED-CHK
TEMP-OFF
MODEL
VER.
RGB
RGB50
CORSS
STEP
COLOR
CHR
CURRENT
HISTORY1
HISTORY2
HISTORY3
HISTORY4
TOTAL
TEMP1
TEMP2
FAN0
FAN1
FAN2
Default
20
1st Layer
OTHER
(0)
110
110
110
100
100
100
—
—
—
—
—
—
127
127
127
257
257
256
256
256
128
128
128
124
68
154
128
132
128
132
0
0
0
0
0
—
—
—
1
1
1
1
1
1
0
0
0
0
0
0
—
—
3
3
3
SPECIAL
EDID
EXIT
2–4
2nd Layer
USB-MODE
HDCP-MODE
PULSE-MODE
EEP-SELECT
EEP-WP
Default
0
0
0
1
0
PG-F211X/PG-F261X
1. Adjustment of ballast unit output power (lamp power)
1. List of parts requiring adjustment
When replacing the following parts, adjust the ballast unit output power (lamp power).
1
2
3
4
5
Part name
Cement resistor
Ballast Control PWB
Ballast microprocessor
5V regulator
Ballast Switching Control
Ref No.
R923
——
IC7707
IC7704
IC7701
Part code
RR-FZA002WJZZ
DUNTKE150WEF0
RH-iXC103WJZZQ
VHiTA78L05F-1Y
VHiM51995AF-1Y
2. Adjustment jigs
The following jigs are required for adjusting the ballast unit output power (lamp power).
1
2
Part name
Adjustment jig (resistance load 25 Ω)
Connecting cord (conversion cable)
Part code
RUNTZA018WJZZ
QCNWKA020WJZZ
3. Ballast unit output power (lamp power) adjustment method
Adjust the ballast unit output power (lamp power) in the following method.
[Setting method]
Tester
(Voltage)
PG-F211X
PG-F261X
Ballast Unit
Lamp Cable
Projector
TP1
Connecting Cord
(QCNWKA020WJZZ)
Adjustment Jig
(RUNTZA018WJZZ)
TP2
2. Adjustment method
1) Unplug the ballast unit lamp cable of the projector from the lamp and connect the cable to the connecting cord
(QCNWKA020WJZZ).
2) Connect the connecting cord (QCNWKA020WJZZ) to the adjustment jig (RUNTZA018WJZZ).
3) Connect TP1 of the adjustment jig (RUNTZA018WJZZ) to the negative terminal of the tester and TP2 to the positive terminal.
4) Turn on the projector.
5) Check the Lamp setting to “Bright”.
6) Ageing the projector for 60 seconds or more.
7) Adjust the volume resistor (R7805) of the ballast control PWB (DUNTKE150WEF0) so that the voltage of the tester reaches 71±0.5V.
Adjustment value: 71±0.5V
CAUTION: (1) Caution for electric shock: Do not touch the test points TP1 and TP2 of the adjustment jig when supplying power since a high voltage
and large current is applied to them.
(2) Caution for heat: Be careful that the resistance load of the adjustment jig produces a high temperature when supplying power.
(3) Connection of the lamp cable: Check that the lamp cable and connecting cord (QCNWKA020WJZZ) are connected securely.
Poor connection may cause smoking or ignition due to arc discharge.
2–5
PG-F211X/PG-F261X
PartsGuide
PARTS GUIDE
No. S57K1PG-F211X
MULTIMEDIA PROJECTOR
MODELS
PG-F211X
PG-F261X
Note:
The reference numbers on the PWB are arranged
in alphabetical order.
CONTENTS
[1]
PRINTED WIRING BOARD
ASSEMBLIES
[2]
CABINET AND MECHANICAL
PARTS
[3]
OPTICAL MECHANISM PARTS
[4]
SUPPLIED ACCESSORIES
[5]
PACKING PARTS
(NOT REPLACEMENT ITEM)
[6]
SERVICE JIGS AND EQUIPMENT
(USE FOR SERVICING)
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and performance of the set.
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
PG-F211X/PG-F261X
NO.
PARTS CODE
PRICE NEW PART
RANK MARK DELIVERY
DESCRIPTION
[1] PRINTED WIRING BOARD ASSEMBLIES
N
DSETUE149FMG0
BZ
J
N
Not Available
-
-
N
N
N
N
N
N
DUNTKE150WEF0
DUNTKE151WEF0
DUNTKE152WEF0
DUNTKE153FMF6
DUNTKE153FMF7
DUNTKE154WEF0
BW
AY
AY
CT
CT
CN
N
N
N
N
J
J
J
J
J
J
BALLAST POWER Ass'y (with Ballast Control Unit)
BALLAST POWER Unit Order the BALLAST POWER Ass'y (DSETUE149FMG0) when
replacing ballast power unit (DUNTKE149WEF0).
BALLAST CONTROL Unit
PHOTO SENSOR Unit
R/C RECEIVER Unit
MAIN Unit (PG-F211X)
MAIN Unit (PG-F261X)
DMD Unit (without the DMD chip)
2
PG-F211X/PG-F261X
[2] CABINET AND MECHANICAL PARTS
1-4
18
10
1
10
30
1-3
40
42
25
10
1-1
31
40
19
1-2
1-5
29
10
17
23
43
24
45
6
15
12
39
22
44
32
39
14
33
2-6
38
2-4
8
2-10
2-11
40
34
9
40
2-5
2-3
27
2-2
2
16
4
41
5
40
2-1
2-1-3
2-9
2-8
37
2-1-1
26
2-1-2
3
2-7
PG-F211X/PG-F261X
NO.
PARTS CODE
PRICE NEW PART
RANK MARK DELIVERY
DESCRIPTION
[2] CABINET AND MECHANICAL PARTS
!
1
1
1-1
1-2
1-3
1-4
1-5
2
2
2-1
2-1-1
2-1-2
2-1-3
2-2
2-3
2-4
2-5
2-6
2-7
2-8
2-9
2-10
2-11
4
5
6
8
9
10
12
14
15
16
17
18
19
22
23
24
25
26
27
29
30
31
32
33
34
37
38
39
40
41
42
43
44
45
CBDYTA264WEF0
CBDYTA265WEF0
Not Available
GCOVAC364WJSA
HDECPA034WJSA
HiNDPC319WJSC
GCOVAC242WJKC
CBDYUA304WEF0
CBDYUA305WEF0
CDORUA075WEF0
Not Available
LX-BZA185WJFN
PSLDHA047WJFW
Not Available
LX-NZ3120CEFW
LX-NZ3144CEFW
LX-NZA014WJFW
QEARPA250WJFW
GLEGPA030WJSA
GLEGPA036WJSA
PSPAZB478WJZZ
QCNW-F721WJQZ
XEBSN30P10000
----AN-XR30LP
LHLDFA011WJKZ
LHLDZA849WJKZ
LX-BZ3049GEFN
LX-BZ3100CEF7
LX-BZA186WJF9
NFANRA076WJ00
NFANRA078WJ00
PCOVPA037WJSA
PCOVUA105WJ00
PCOVZA099WJZZ
PCOVZA100WJZZ
PSLDMB118WJFW
PSLDMB119WJFW
PSLDMB122WJFW
PSLDMB123WJFW
PSPAGA370WJKZ
PSPAGA371WJKZ
PZETKA227WJKZ
PZETKA233WJKZ
PZETKA240WJKZ
QCNW-F711WJQZ
QCNW-F718WJPZ
QCNW-F720WJQZ
RSP-ZA085WJQZ
XBBSN30P06000
XBPSN30P08JS0
XEBSN30P10000
Not Available
PCOVWA015WJKZ
QEARPA256WJFW
QCNW-G254WJQZ
NSFTZ0134CEFW
BP
BP
AE
AK
AM
AS
BT
BT
AQ
AB
AK
AB
AC
AC
AK
AK
AP
AC
AN
AA
AC
AQ
AB
AA
AD
BM
BP
AU
AF
AE
AF
AM
AK
AZ
AX
AP
AW
AX
AD
AG
AZ
AY
AG
AP
AA
AB
AA
AC
AB
AH
AD
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
Top Body Ass'y (PG-F211X)
Top Body Ass'y (PG-F261X)
Top Body
Cover
Decoration Plate
Indicator
Cover
Bottom Body Ass'y (PG-F211X)
Bottom Body Ass'y (PG-F261X)
Lamp Door Ass'y
Lamp Door
Screw
Shield
Bottom Body
Nut
Nut, x4
Nut
Bottom Earth Shield
Foot (Rear Adjuster)
Foot (Front Adjuster)
Spacer
Connecting Cord
Screw
Refer to Optical Mechanism Parts
Lamp Unit
Rivet (Power PWB)
Holder (Bimetal)
Screw, x4
Screw, x7
Screw, x2
Fan
Fan
Cover
Cover
Cover
Cover
Shield
Shield
Shield
Shield
Spacer
Spacer
Insulator
Insulator
Insulator
Connecting Cord
Connecting Cord
Connecting Cord
Speaker
Screw
Screw, x3
Screw, x18
Serial No Label
Spacer
Ground-Part
Connecting Cord
Shaft for DVI Socket, x2
4
PG-F211X/PG-F261X
[3] OPTICAL MECHANISM PARTS
4-33
11
11
11
13
13
4-33
4-11
4-33
11
13
20
13
21
7
4-27
28
4-33
4-33
4-25
35
4-16
36
4-24
4-29
4-36
4-33
4-34
4-33
4-13
4-34
4-8
4-33
4-33
4-12
4-33
4-33
4-31
4-31
4-33
4-31
4-31
4-5
4-26
4-6
4-33
4-31
4-28
4-31
4-18
4-31
4-33
4-7
4-20
4-21
4-30
4-15
4-33
4-22
4-31
4-33
4-17
4-2
4-32
4-23
4-1
4-32
4-32
4-4
4-3
4-35
4-35
4-19
4-33
4-14
4-33
4-33
4-33
4-10
4-9
4-33
4-33
5
PG-F211X/PG-F261X
NO.
PARTS CODE
PRICE NEW PART
RANK MARK DELIVERY
DESCRIPTION
[3] OPTICAL MECHANISM PARTS
4-1
4-2
4-3
4-4
4-5
4-6
4-6
4-7
4-8
4-9
4-10
4-11
4-12
4-13
4-14
4-15
4-16
4-17
4-18
4-19
4-20
4-21
4-22
4-23
4-24
4-25
4-26
4-27
4-28
4-29
4-30
4-31
4-32
4-33
4-34
4-35
4-36
7
11
13
20
21
28
35
36
LANGKB121WJFW
LCHSKA024WJFW
LHLDZA845WJKZ
LX-EZA027WJFN
MSPRPA095WJFW
MSPRPA096WJFW
MSPRPA103WJFW
MSPRPA097WJFW
NFANRA077WJ00
PCOVPA036WJSA
PCOVPA038WJSA
PCOVZA089WJFW
PCOVZA093WJKZ
PCOVZA094WJKZ
PCOVZA095WJFW
PCOVZA096WJFW
PDUC-A088WJFW
PFiLWA120WJZZ
PLNS-A059WJZZ
PLNS-A080WJZZ
PLNS-A083WJZZ
PLNS-A084WJZZ
PLNS-A085WJZZ
PMiR-A125WJZZ
PRDARA446WJFW
PSLDHA048WJFW
PSLDPA077WJFW
PSLDPA072WJKZ
PSLDPA073WJFW
RH-HXA040WJQZ
TLABZB026WJZZ
XBBS925P06000
LX-BZA205WJFN
XBBSN30P06000
XBPSN30P20JS0
XEPSN17P05000
PSLDPA078WJFW
LHLDZA612WJFW
LX-BZA110WJF7
MSPRCA062WJFJ
PRDARA445WJFW
PSHEGA040WJZZ
PSPAZA768WJZZ
QSOCZA114WJZZ
RDMDPA027WJZZ
AE
BQ
AN
AC
AF
AG
AG
AK
BH
AR
AS
AP
AM
AN
AL
AG
AF
CC
BF
AT
AT
AT
BD
AU
AQ
AK
AM
AZ
AD
AS
AE
AA
AA
AA
AB
AB
AF
AL
AC
AB
AZ
AE
AD
BA
CW
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
Fixing Metal
Chassis
Holder
For Focus Ring, x3
Spring
Spring (PG-F261X)
Spring (PG-F211X)
Spring
Fan
Cover
Cover
Cover
Cover
Cover
Cover
C/W Cover
Exhaust Duct
Filter
Lens
Lens
Lens
Lens
Lens
Mirror
Heat Sink
Shield
Shield
Shield
Shield
Thermistor
No. Label
Screw, x9
Screw, x3
Screw, x22
Screw, x2
Screw, x2
Flat Ray Shield
Holder (Backer Plate)
Screw, x4
Spring, x4
Heat Sink
Sheet
Spacer
Socket
DMD Chip, 0.55" XGA
6
PG-F211X/PG-F261X
[4] SUPPLIED ACCESSORIES
X1
X3
X6
X4
X2
X5
X9
X10
*
NO.
PARTS CODE
PRICE NEW PART
RANK MARK DELIVERY
DESCRIPTION
[4] SUPPLIED ACCESSORIES
!
X1
X2
X3
X4
X5
X6
X7
X8
X9
X10
CCAPHA027WJSA
GCASNA021WJSA
QACCDA007WJPZ
QCNWGA045WJPZ
QCNWGA091WJPZ
RRMCGA581WJSA
TGAN-A811WJZZ
TGAN-A840WJZZ
TiNS-D338WJZZ
UDSKAA094WJZZ
AH
BD
AR
AU
AZ
BD
AB
AC
AN
AQ
N
N
N
N
N
N
N
J
J
J
J
J
J
J
J
J
J
Lens Cap
Storage case
AC Cord (for U.S.A)
RGB Cable
DIN-D-sub RS-232C adaptor
Remote Control
SECL Warranty (for Canada)
SEC Warranty (for USA)
Operation Manual
CD-ROM
7
PG-F211X/PG-F261X
[5] PACKING PARTS (NOT REPLACEMENT ITEM)
S5
S6
S2
S8
S3
S4
S7
S1
8
PG-F211X/PG-F261X
NO.
PARTS CODE
PRICE NEW PART
RANK MARK DELIVERY
DESCRIPTION
[5] PACKING PARTS (NOT REPLACEMENT ITEM)
S1
S1
S2
S3
S4
S5
S6
S7
S8
SPAKCD746WJZZ
SPAKCD747WJZZ
SPAKFB224WJZZ
SPAKPA869WJZZ
SPAKXB477WJZZ
SSAKA0160CEZZ
SSAKAA097WJZZ
TLABVA333WJZZ
TLABV0003SEZZ
-
N
N
N
N
N
N
N
-
Packing Case (PG-F211X)
Packing Case (PG-F261X)
Accessory Case
Wrapping Paper
Packing Add
Polyethylene Bag
Polyethylene Bag (for Storage case)
Bar Code Label
Model Name Label
[6] SERVICE JIGS AND EQUIPMENT (USE FOR SERVICING)
N
N
N
N
N
N
QCNW-C516WJQZ
QCNWKA006WJZZ
QCNWKA008WJZZ
QCNWKA019WJZZ
RUNTZA018WJZZ
QCNWKA020WJZZ
AG
AX
AP
BU
DR
AX
J
J
J
J
J
J
Extension Cable, 3pins L=200mm, Main to Fan, x2
Extension Cable, 4pins L=500mm, Main to Fan
Extension Cable, 14pins, Main to Power
Extension Cable, 120pins, Main to DMD
Adjustment Jig, for the Ballast Unit
Extension Cable, 3 to 2pins
9
PG-F211X/PG-F261X
COPYRIGHT © 2007
2006 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No Part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any from or by any means, electronic, mechanical,
photocopying , recording, or otherwise, without
prior written permission of the publisher.
TQ2242-S YK. DS
SHARP CORPORATION
AV Systems Group
CS Promotion Center
Yaita,Tochigi 329-2193, Japan