- No category
advertisement
Plate/Base
Dispenser
Service Manual
Spectra Models IDSP2 & IDSP3
Colossus Models IDPC2/0120 & IDPC3/0180
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Unpack & Set-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Electrical Characteristics & Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Spring Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Operation & Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Dinex® Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Replacement Parts-Spectra . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Replacement Parts-Colossus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Wiring Diagram-Spectra. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Wiring Diagram-Colossus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
For Service Information, call 1-888-673-4639
Please provide following information:
• Model number
• Serial number
• Part Description and number as shown in parts list.
Printed in the USA
Manual No. PBD Rev-03/03
DINEX INTERNATIONAL, INC. • 628-2 HEBRON AVENUE, GLASTONBURY CT 06033 • WWW.DINEX.COM
Introduction:
Congratulations: You have just purchased one of the finest pieces of equipment on the market today. Before installing or operating our new Dinex® Products equipment you should read through this material. This manual should be retained for further reference as it contains installation and operating instructions, service tips, part list and warranty information. Should you have any questions concerning the Equipment, please call the Dinex Hotline at 1-888-673-
4639 (Monday through Friday from 8 am to 5 pm, Eastern
Standard Time).
!
IMPORTANT: For your safety, read and follow all cautions, information and warnings
FREIGHT DAMAGE CLAIMS
Your Dinex® Products equipment was carefully inspected and packed before leaving our factory. The transportation company assumes full responsibility for safe delivery of this equipment. Dinex® Products cannot assume responsibility for damage or loss incurred in transit. Visible damage or loss should be noted on freight bill and signed by person making delivery.
A freight claim should be filed immediately with the transportation company. If damage is unnoticed or concealed until equipment is unpacked, notify the transportation company immediately and tell them you want to file a concealed damage claim. This must be done within fifteen
(15) days after delivery was made. Be sure to retain all packing material and cartons.
!
WARNING: Installation of this equipment should be performed only by persons qualified or licensed to install electrical equipment.
• Adjustments and service work should be performed only by a qualified service technician. Service is available through Authorized Dinex® Products Parts & Service
Distributors throughout the United States. For a complete listing of these consult your distributor listing or write Dinex® Products for the name of the nearest distributor.
• This equipment in intended for commercial use only.
Not for household use.
• Use of other than genuine Dinex® Products replacements parts or service work performed by other than authorized Dinex® Products service agents will void the warranty.
• Do not use any corrosive cleaners. Use only cleaners approved for stainless steel.
Page 2
Installation:
ELECTRICAL CHARACTERISTICS
For use with 208 or 240 Volts, single phase, 60 Hz.
Heater: 3200 Watts at 240 Volts
3200 Watts at 208 Volts
Total Amps: 240 Volts =13.4
208 Volts =15.2
Supply plug (cap): NEMA 6-20P
ELECTRICAL CONVERSION
This unit is factory wired for 240 Volts AC. For conversion to 208 Volt applications, disconnect power to equipment, remove back panel and attach blue insulated jumper wire on heating element. See page 7 and 8 of this manual.
!
NOTE: This conversion is not covered under warranty.
TO ADJUST SPRING TENSION IN SILO
1. Disconnect power to dispenser, remove lids and allow unit to cool down.
2. Grasp the base carrier and lift silo assembly up and out.
3. Loosen two cap nuts located at the top of the silo assembly.
4. Slide inner cover up and out. Springs are now accessible.
Spring Settings
Type
Stainless Bases
Therma-Cite (9” round)
China Plates
Uncolored
5
3
5
Green
0
2
2
5. Remove springs that are not required.
6. Assemble by reversing the above steps.
Operation Instructions:
Operation-General
1. Load plates or bases into the dispenser and cover with lids.
2. Approximate cycle time is 1-1/2 to 2 hours.
3. While dispensing plates or bases, the lids may be hung on the brackets located at each end of the dispenser.
4. If unit fails to operate first try resetting the high limit.
The high limit is a small red push button located on the control panel.
OPERATION-SPECTRA-100
Use the super-heat cycle only on stainless steel bases. This cycle is to be employed only at the beginning of a heat-up cycle. To actuate, press red button located on the control panel. To avoid malfunction of the super-heat cycle, allow the unit to cool down slightly before re-employing the super-heat cycle.
Closely follow the heating instructions listed below.
!
CAUTION: Never use the super-heat cycle for china or
Therma-Cite plates. Excessive temperatures through superheat as well as setting the thermostat control too high will damage your plates and could cause a hazard.
Type
Stainless Bases
Therma-Cite*
China Plates
Heating Instructions
Operating
Thermostat
7
2
3
Super-Heat
Thermostat
9
Off
Off
!
CAUTION: Damage to Therma-Cite or Melamine plates will occur if the Super-Heat cycle is used. Damage to
Therma-Cite and Melamine plates can also occur if operation thermostat setting is higher than number 2.
OPERATION-COLOSSUS
Start with a thermostat setting of a 6 and adjust as required for the application.
Maintenance
CLEANING
!
CAUTION: Disconnect electrical power to unit prior to cleaning inside of unit. Clean with mild soap and water or cleaners approved for stainless steel. Clean and wipe dry.
!
CAUTION: Never spray wash unit or use chlorine or other caustic cleaners.
Dinex International, Inc. (“Dinex”) warrants that its DES
Equipment (“Equipment”) shall be free from defects in materials and workmanship for a period of one (1) year from the date of delivery to the initial end-user (“End-
User”) (the “Warranty Period”). Dinex shall be notified of all
Equipment claimed to be defective and covered by this warranty. The End-User shall include in this notification the serial number and a copy of the Bill of Lading (showing delivery date) for the Equipment. If Dinex’s investigation establishes the existence of the alleged defects, then Dinex shall, at Dinex’s choice and expense, repair or replace the affected Equipment (provided that the costs of labor on such repairs shall only be included for proper warranty claims asserted in writing within 1 year of delivery date) and reimburse End-User for the reasonable shipping costs for returning the Equipment to Dinex, if any.
This warranty does not apply to defects in any Equipment caused by: (1) normal wear and tear; (2) failure to comply with any Dinex-provided operation or maintenance instructions; (3) alteration or modification(s) by parties other than Dinex or (4) misuse, neglect, accident, Acts of
God or other causes beyond the control of Dinex after delivery of the Equipment by Dinex to its authorized distributor.
Repaired or replacement Equipment under this warranty shall be warranted for the unexpired portion of the original Warranty Period applicable thereto plus the period from notice to Dinex of such defect until completion of repair or return to the point of original delivery to Buyer.
THIS WARRANTY IS IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, WHETHER ARISING BY LAW, CUSTOM,
CONDUCT OR USAGE OF TRADE, AND THE RIGHTS AND
REMEDIES PROVIDED HEREIN ARE EXCLUSIVE AND
PROVIDED IN LIEU OF ANY OTHER RIGHTS AND
REMEDIES. DINEX SHALL HAVE NO LIABILITY OTHER
THAN AS PROVIDED IN THIS WARRANTY, WHETHER
CLAIMED IN CONTRACT, EQUITY, TORT OR OTHERWISE,
FOR OR RESULTING FROM DEFECTS IN MATERIALS OR
WORKMANSHIP OR OTHERWISE.
IN NO EVENT SHALL DINEX BE LIABLE FOR ANY
SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL
DAMAGES ARISING OUT OF OR IN CONNECTION WITH
THE EQUIPMENT, REGARDLESS WHETHER SUCH
LIABILITY SHALL BE CLAIMED IN CONTRACT, TORT,
EQUITY OR OTHERWISE.
Page 3
Dispensing
Mechanism
Complete
Replacement Parts
Spectra Models IDSP2 & IDSP3
Key Description Part No.
1 Cord & Plug
2 Pilot Light
3 Ball Bearing
4 On-Off Switch
5 Knob
IS0084525
IS0189500
IS0116804
IS0330875
IS0178525
6 Thermostat Hi-Limit IS0113752
7 Bracket-Motor Mount IS0675813
8 Motor IS0113751
9 Base Carrier Assembly Contact Factory
10 Track Contact Factory
11 Cover Contact Factory
12 Heater
13 Fan Blade
14 Bracket, Cap Tube
IS0113753
IS0113570
IS0677273
Key Description Part No.
15 Handle-Door
16 Caster-With Brake
17 Caster-No Brake
18 Spring (Uncolored)
19 Spring (Green)
20 Door Gasket
21 Push Button Switch
22 Thermostat-Super Heat
23 Thermostat-Operating
IS0113774
IS0053500
IS0053510
IS0113747
IS0113748
IS0116897
IS0113750
IS0115421
IS0350100
24 Contactor
25 Terminal Block
IS0082500
IS0113754
26 Door Complete
27 Push Bar
IS08830367
IS08830359
28 Dispensing Mechanism Complete IS08830354
Page 4
Dispensing
Mechanism
Complete
Replacement Parts
Colossus Models IDPC2/0120 & IDPC3/0180
Key Description Part No.
1 Cord & Plug
2 Pilot Light
3 Ball Bearing
4 On-Off Switch
IS0084525
IS0189500
IS0116804
IS0330875
5 Knob
6 Thermostat Hi-Limit
IS0178525
IS0113752
7 Bracket-Motor Mount IS0675813
8 Motor IS0113751
9 Base Carrier Assembly Contact Factory
10 Track Contact Factory
11 Cover Contact Factory
12 Heater IS0113753
13 Fan Blade IS0113570
Key Description Part No.
14 Bracket, Cap Tube
15 Handle-Door
16 Caster-With Brake
17 Caster-No Brake
18 Spring (Uncolored)
19 Spring (Green)
20 Door Gasket
21 Thermostat-Operating
IS0677273
IS0113774
IS0053500
IS0053510
IS0113747
IS0113748
IS0116897
IS0349160
22 Door Complete
23 Push Bar
IS08830367
IS08830359
24 Dispensing Mechanism Complete IS08830354
Page 5
Page 6
Page 7
DINEX INTERNATIONAL, INC.
Page 8
WWW.DINEX.COM
628-2 HEBRON AVENUE, GLASTONBURY CT 06033 • 1.800.523.9752
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project