advertisement
T81
T82
T85
T86
TREADMILL OWNER’S MANUAL
Read the TREADMILL gUIDE before using this OWNER’S MANUAL.
2
ASSEMBLY
WARNING
There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the treadmill could have frame parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to the treadmill, the assembly instructions must be reviewed and corrective actions should be taken.
Before proceeding, find your treadmill’s serial number located on the front stabilizer tube and enter it in the space provided below. Also locate the model name which is next to the serial number.
ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOXES BELOW:
SERIAL NUMBER:
MODEL NAME:
TEMPO TREADMILL
3
T86 shown
MOBILE PHONE HOLDER (T86 ONLY)
GRIP PULSE HANDRAILS
HANDLEBARS
CONSOLE MAST
MOTOR COVER
4
COMFORTSTEP (T86 ONLY)
TRANSPORT WHEEL
COMFORTGEL CUSHIONING (T86 ONLY)
RUNNING BELT / RUNNING DECK
SIDE RAIL
CONSOLE CONTROLS AND DISPLAY WINDOWS
CONSOLE
WATER BOTTLE HOLDER
HANDRAIL TOGGLE (T86 ONLY)
SAFETY KEY PLACEMENT
ON/OFF SWITCH
CIRCUIT BREAKER
POWER CORD
S/N STICKER
REAR ROLLER TENSION/ADJUSTMENT BOLTS
TOOLS INCLUDED:
F 5 mm L-Wrench /screwdriver
(T81/82)
F 6 mm L-Wrench (T81/82)
F 5 mm L-Wrench (T85/86)
F 5 mm T-Wrench (T85/86)
PARTS INCLUDED:
F 1 Console Assembly
F 2 Console Masts
F 1 Hardware Kit
F 1 Safety Key
F 1 Power Cord
F 1 Silicone
F 1 Cellphone/MP3 Holder
(T86 only)
NEED HELP?
If you have questions or if there are any missing parts, contact your local dealer.
PRE ASSEMBLY
UNPACKING
Place the treadmill carton on a level flat surface. It is recommended that you place a protective covering on your floor. Take CAUTION when handling and transporting this unit. Never open box when it is on its side. Once the banding straps have been removed, do not lift or transport this unit unless it is fully assembled. Unpack and assemble the unit where it will be used. Never grab hold of any portion of the incline frame and attempt to lift or move the treadmill.
ALL
MODELS
WARNING
DO NOT ATTEMPT TO LIFT THE TREADMILL! Do not move or lift treadmill from packaging until specified to do so in the assembly instructions. You may remove the plastic wrap from console masts.
WARNING
FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY!
NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt.
NOTE: A light application of grease may aid in the installation of hardware. Any grease, such as lithium bike grease is recommended.
5
T82
Shown
T81 & T82 ASSEMBLY STEP 1
HARDWARE fOR STEP 1 :
LONG BOLT (a)
M8 x 50L
Qty: 4
SHORT BOLT (b)
M8 x 16L
Qty: 2
FLAT WASHER (d)
Ø 8
Qty: 4
ARC WASHER (c)
Ø 8
Qty: 2 b c
RIGHT CONSOLE MAST
LEFT CONSOLE MAST
A A Open the box and remove all parts underneath the running deck by lifting the running deck upward.
B Open HARDWARE pARts for Step 1
C Align and attach LEFt CONsOLE MAst with base frame bracket by using 2 LONG BOLts ( a ) ,
1 sHORt BOLts ( b ) , 2 FLAt WAsHERs ( d ) and 1
ARC WAsHER ( c ).
D Connect the CONsOLE CABLEs at RIGHt
CONsOLE MAst and carefully tuck wires to
CONsOLE MAst to avoid damage.
E Repeat Step C on the RIGHt CONsOLE MAst.
NOTE: Do not pinch or break any wire when assembling the console mast. You may need extra help assembling step 1 o 2 and DO NOT fully tighten the bolts until step 2 is completed. a d
MAIN FRAME BRACKET
6
(T82 SHOWN)
T81 & T82 ASSEMBLY STEP 2
HARDWARE fOR STEP 2 :
SHORT BOLT (b)
M8 x 16 L
Qty: 4
ARC WASHER (c)
Ø 8
Qty: 4 c b
RIGHT CONSOLE MAST
LEFT CONSOLE MAST
A Open HARDWARE pARts for Step 2
B gently hold the CONsOLE above the CONsOLE
MAst.
C Connect the CONsOLE CABLEs at right hand side, carefully tucking wires in RIGHt CONsOLE MAst to avoid damage.
D Attach the CONsOLE to the CONsOLE
MAst using 4 sHORt BOLts ( b ) and 4 FLAt
WAsHERs ( c ).
NOTE: T81 & 82 console fixing from beneath while
T85 & 86 is screw in from inner side as shown in the left image. Be careful not to pinch any wires and make sure you fully tighten all bolts before starting using the treadmills.
T82
Shown
(T82 SHOWN)
7
T86
Shown
T85 & T86 ASSEMBLY STEP 1
HARDWARE fOR STEP 1 :
LONG BOLT (A)
M8 x 55L
Qty: 4
SHORT BOLT (B)
M8 x 20L
Qty: 2
SPRING WASHER (D)
Ø 8.2
Qty: 6
FLAT WASHER (E)
Ø 8.2
Qty: 4
ARC WASHER (C)
Ø 8.4
Qty: 2
B D C
RIGHT CONSOLE MAST
LEFT CONSOLE MAST
A A Open the box and remove all parts underneath the running deck by lifting the running deck upward.
B Open HARDWARE pARts for Step 1
C Align and attach LEFt CONsOLE MAst with base frame bracket by using 2 LONG BOLts (A) ,
1 sHORt BOLts (B) , 3 spRING WAsHERs (D) ,
2 FLAt WAsHERs (E) and 1 ARC WAsHER (C).
D Connect the CONsOLE CABLEs at RIGHt
CONsOLE MAst and carefully tuck wires to
CONsOLE MAst to avoid damage.
E Repeat Step C on the RIGHt CONsOLE MAst.
NOTE: Do not pinch or break any wire when assembling the console mast. You may need extra help assembling step 1 o 2 and DO NOT fully tighten the bolts until step 2 is completed.
8
A D
(T86 SHOWN)
E
MAIN FRAME BRACKET
T85 & T86 ASSEMBLY STEP 2
HARDWARE fOR STEP 2 :
SHORT BOLT (B)
M8 x 20L
Qty: 4
SPRING WASHER (D)
Ø 8.2
Qty: 4
FLAT WASHER (E)
Ø 8.2
Qty: 4
A Open HARDWARE pARts for Step 2
B gently hold the CONsOLE above the CONsOLE
MAst.
Connect the CONsOLE CABLEs at right hand side, carefully tucking wires in RIGHt CONsOLE MAst to avoid damage.
C-1 (t86 ONLY)
Connect HANDRAIL tOGGLE KEY CABLEs at LEFt and RIGHt CONsOLE MAst , carefully tucking wires in CONsOLE MAst .
C Attach the CONsOLE to the CONsOLE MAst using 4 sHORt BOLts (B) , 4 spRIN WAsHERs
(D) and 4 FLAt WAsHERs (E).
E
D
B
LEFT CONSOLE MAST
RIGHT CONSOLE MAST
NOTE: T81 & 82 console fixing from beneath while
T85 & 86 is screw in from inner side as shown in the left image. Be careful not to pinch any wires and make sure you fully tighten all bolts before starting using the treadmills.
T86
Shown
(T86 SHOWN)
9
T86
Shown
ASSEMBLY STEP 3
10
(T86 SHOWN)
YOU ARE FINISHED!
T81
Max. User Weight: 115 kg / 253 lbs.
Product Weight: 54 kg / 119 lbs.
Overall Dimension: 171 x 71 x 132 cm / 67” x 28” x 52”
Folding Dimension: 103 x 71 x 139 cm / 40.5” x 28” x 55”
Complies with EN957-1, EN957-6, HB
T82
Max. User Weight: 115 kg / 253 lbs.
Product Weight: 58 kg / 128 lbs.
Overall Dimension: 171 x 71 x 132 cm / 67” x 28” x 52”
Folding Dimension: 108 x 71 x 135 cm / 42.5” x 28” x 53”
Complies with EN957-1, EN957-6, HB
T85
Max. User Weight: 115 kg / 253 lbs.
Product Weight: 60 kg / 132 lbs.
Overall Dimension: 173 x 79 x 136 cm / 68” x 31” x 53.5”
Folding Dimension: 96 x 79 x 145 cm / 38”x 31” x 57”
Complies with EN957-1, EN957-6, HB
T86
Max. User Weight: 115 kg / 253 lbs.
Product Weight: 60 kg / 132 lbs.
Overall Dimension: 173 x 79 x 136 cm / 68” x 31” x 53.5”
Folding Dimension: 96 x 79 x 145 cm / 38”x 31” x 57”
Complies with EN957-1, EN957-6, HB
T81
Max. User Weight: 115 kg / 253 lbs.
Product Weight: 54 kg / 119 lbs.
Overall Dimension: 171 x 71 x 132 cm / 67” x 28” x 52”
Folding Dimension: 103 x 71 x 139 cm / 40.5” x 28” x 55”
Complies with EN957-1, EN957-6, HB
T82
Max. User Weight: 115 kg / 253 lbs.
Product Weight: 58 kg / 128 lbs.
Overall Dimension: 171 x 71 x 132 cm / 67” x 28” x 52”
Folding Dimension: 108 x 71 x 135 cm / 42.5” x 28” x 53”
Complies with EN957-1, EN957-6, HB
T85
Max. User Weight: 115 kg / 253 lbs.
Product Weight: 60 kg / 132 lbs.
Overall Dimension: 173 x 79 x 136 cm / 68” x 31” x 53.5”
Folding Dimension: 96 x 79 x 145 cm / 38”x 31” x 57”
Complies with EN957-1, EN957-6, HB
T86
Max. User Weight: 115 kg / 253 lbs.
Product Weight: 60 kg / 132 lbs.
Overall Dimension: 173 x 79 x 136 cm / 68” x 31” x 53.5”
Folding Dimension: 96 x 79 x 145 cm / 38”x 31” x 57”
Complies with EN957-1, EN957-6, HB
TREADMILL OPERATION
This section explains how to use your treadmill’s console and programming. The BASIC OPERATION section in the
TREADMILL gUIDE has instructions for the following:
• LOCATION Of THE TREADMILL
• USING THE SAfETY KEY
• fOLDING THE TREADMILL
• MOVING THE TREADMILL
• LEVELING THE TREADMILL
• TENSIONING THE RUNNING BELT
• CENTERING THE RUNNING BELT
• USING THE HEART RATE fUNCTION
11
T81
Shown
A
DISTANCE
距离
TIME
时间
.
HEART RATE
心率
CALORIES
卡路里
SPEED
速度
B
BMI TEST
体脂测试
Energy Saver
节能模式
2 km/h
公里/时
4 km/h
公里/时
SPEED
速度
6 km/h
公里/时
START
开始
QUICK START
快速启动
ENTER
确认
CHANGE DISPLAY
切换显示
STOP
停止
HOLD TO RESET
按住重设
8 km/h
公里/时
SPEED
速度
10 km/h
公里/时
12 km/h
公里/时
C
D C E F G H I
12
T81 CONSOLE OPERATION
Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use.
A) LED DISPLAY WINDOWS: Time, Distance,Speed, Calories, Heart Rate and Steps (with 10K Steps program only).
B) BMI TEST: BMI test direct key. Input your weight and height after pressing this key. Your machine will help you calculate your BMI index for furture tracking.
C) ENERGY SAVER : To minimize energy consumption, your machine will enter energy saver mode automatically (after entering stand-by mode for 15 mins) and could be quickly waken up with a touch of a button.
D) PROGRAM DIRECT KEYS: Intuitive direct key help you set your program more easily. (Refer to program information for more details) .
E) SPEED KEYS: used to adjust speed in small increments (0.1 KMH increments).
f) ENTER BUTTON : used to confirm setting of workout program or user profile.
G) START: press to begin exercising, start your workout, or resume exercising after pause.
H) SAfETY KEY POSITION: enables treadmill when safety key is inserted.
I) STOP: press to pause/end your workout. Hold for 3 seconds to reset the console.
T81
Shown
13
T82
Shown
A
DISTANCE
距离
TIME
时间
.
INCLINE
坡度
CALORIES
卡路里
SPEED
速度
HEART RATE
心率
B
BMI TEST
体脂测试
Energy Saver
节能模式
3
%
6
%
INCLINE
坡度
9
%
START
开始
QUICK START
快速启动
ENTER
确认
CHANGE DISPLAY
切换显示
STOP
停止
HOLD TO RESET
按住重设
4 km/h
公里/时
8 km/h
公里/时
SPEED
速度
12 km/h
公里/时
C
D C E F G H I J
14
T82 CONSOLE OPERATION
Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use.
A) LED DISPLAY WINDOWS: Time, Distance,Speed, Incline, Calories, Heart Rate and Steps (with 10K Steps program only).
B) BMI TEST: BMI test direct key. Input your weight and height after pressing this key. Your machine will help you calculate your BMI index for furture tracking.
C) ENERGY SAVER : To minimize energy consumption, your machine will enter energy saver mode automatically (after entering stand-by mode for 15 mins) and could be quickly waken up with a touch of a button.
D) PROGRAM DIRECT KEYS: Intuitive direct key help you set your program more easily. (Refer to program information for more details) .
E) INCLINE KEYS: used to adjust incline in small increments (0.5% Increments).
f) ENTER BUTTON : used to confirm setting of workout program or user profile.
G) START: press to begin exercising, start your workout, or resume exercising after pause.
H) SAfETY KEY POSITION: enables treadmill when safety key is inserted.
I) STOP: press to pause/end your workout. Hold for 3 seconds to reset the console.
J) SPEED KEYS: used to adjust speed in small increments (0.1 KMH increments).
T82
Shown
15
T85
Shown
A B
C
BMI TEST
体脂测试
INCLINE
坡度
DISTANCE
距离
.
SPEED
速度
Energy Saver
节能模式
MyTrain
专属课程
D
F G H I J K
16
T85 CONSOLE OPERATION
Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use.
A) LED DISPLAY WINDOWS: Time, Distance,Speed, Incline, Calories, Heart Rate and Steps (with 10K Steps program only).
B) ENERGY SAVER : To minimize energy consumption, your machine will enter energy saver mode automatically (after entering stand-by mode for 15 mins) and could be quickly waken up with a touch of a button.
C) BMI TEST: BMI test direct key. Input your weight and height after pressing this key. Your machine will help you calculate your BMI index for furture tracking.
D) MY TRAIN: A quick program key to help you save your workout settings and ready for next exercise. After finish any workout press this key for 3 seconds to save all the changes you made and press this program key to re-experience your favorite workout.
E) PROGRAM DIRECT KEYS: Intuitive direct key help you set your program more easily. (Refer to program information for more details) .
f) INCLINE KEYS: used to adjust incline in small increments (0.5% Increments).
G) ENTER BUTTON : used to confirm setting of workout program or user profile.
H) START: press to begin exercising, start your workout, or resume exercising after pause.
I) SAfETY KEY POSITION: enables treadmill when safety key is inserted.
J) STOP: press to pause/end your workout. Hold for 3 seconds to reset the console.
K) SPEED KEYS: used to adjust speed in small increments (0.1 KMH increments).
T85
Shown
17
T86
Shown
A B C
D
INCLINE
坡度
CALORIES
卡路里
DISTANCE
距离
TIME
时间
.
SPEED
速度
HEART RATE
心率
Energy Saver
节能模式
Heart Rate
心率提示系统
E
G H I G K L
18
T86 CONSOLE OPERATION
Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use.
A) LED DISPLAY WINDOWS: Time, Distance,Speed, Incline, Calories, Heart Rate and Steps (with 10K Steps program only).
B) ENERGY SAVER : To minimize energy consumption, your machine will enter energy saver mode automatically (after entering stand-by mode for 15 mins) and could be quickly waken up with a touch of a button.
C) HEART RATE INDICATOR (T86 ONLY): A monitor system to help you stay in your best heart rate range and reach desired performance.
(See page 26 for more information)
D) BMI TEST: BMI test direct key. Input your weight and height after pressing this key. Your machine will help you calculate your BMI index for furture tracking.
E) MY TRAIN: A quick program key to help you save your workout settings and ready for next exercise. After finish any workout press this key for 3 seconds to save all the changes you made and press this program key to re-experience your favorite workout.
f) PROGRAM DIRECT KEYS: Intuitive direct key help you set your program more easily. (Refer to program information for more details) .
G) INCLINE KEYS: used to adjust incline in small increments (0.5% Increments).
H) ENTER BUTTON : used to confirm setting of workout program or user profile.
I) START: press to begin exercising, start your workout, or resume exercising after pause.
J) SAfETY KEY POSITION: enables treadmill when safety key is inserted.
K) STOP: press to pause/end your workout. Hold for 3 seconds to reset the console.
L) SPEED KEYS: used to adjust speed in small increments (0.1 KMH increments).
T86
Shown
19
T81
T82
Shown
T81 DISPLAYS T82 DISPLAYS
DISTANCE
距离
TIME
时间
DISTANCE
距离
TIME
时间
HEART RATE
心率
CALORIES
卡路里
SPEED
速度
INCLINE
坡度
CALORIES
卡路里
SPEED
速度
HEART RATE
心率
Energy Saver
节能模式
DISPLAY WINDOWS
• TIME: Shown as minutes : seconds. View the time remaining or the time elapsed in your workout.
• DISTANCE: Shown as km or miles. Indicates distance traveled or distance remaining during your workout.
• SPEED: Shown as MPH or KMPH. Indicates how fast your walking or running surface is moving.
• CALORIES: Total calories burned or calories remaining left to burn during your workout.
• HEART RATE: Shown as BPM (beats per minute). Used to monitor your heart rate (displayed when contact is made with both pulse grips).
Energy Saver
节能模式
• INCLINE (T82 ONLY): Shown as percent. Indicates the incline of your walking or running surface.
• STEPS: (Use on 10K Steps program only). To display the steps remained in your workout.
20
T85 DISPLAYS
INCLINE
坡度
CALORIES
卡路里
DISTANCE
距离
TIME
时间
.
STEP
步伐
SPEED
速度
HEART RATE
心率
Energy Saver
节能模式
T86 DISPLAYS
INCLINE
坡度
CALORIES
卡路里
DISTANCE
距离
TIME
时间
.
STEP
步伐
SPEED
速度
HEART RATE
心率
Energy Saver
节能模式
Heart Rate
Indicator
心率提示系統
T85
T86
Shown
DISPLAY WINDOWS
• TIME: Shown as minutes : seconds. View the time remaining or the time elapsed in your workout.
• DISTANCE: Shown as km or miles. Indicates distance traveled or distance remaining during your workout.
• SPEED: Shown as MPH or KMPH. Indicates how fast your walking or running surface is moving.
• CALORIES: Total calories burned or calories remaining left to burn during your workout.
• HEART RATE: Shown as BPM (beats per minute). Used to monitor your heart rate (displayed when contact is made with both pulse grips).
• INCLINE: Shown as percent. Indicates the incline of your walking or running surface.
• STEPS: Use on 10K Steps program only. To display the steps remained in your workout.
• HEART RATE INDICATOR (T86 ONLY): To monitor your heart rate performance. See page 26 for more detail information.
21
ALL
MODELS
GETTING STARTED
1) Check to make sure no objects are placed on the belt that will hinder the movement of the treadmill.
2) Plug in the power cord and turn the treadmill ON.
3) Stand on the side rails of the treadmill.
4) Attach the safety key clip to part of your clothing making sure that it is secure and will not become detached during operation.
5) Insert the safety key into the safety keyhole in the console.
6) You have two options to start your workout:
A) QUICK START UP
Simply press the START key to begin working out.
Time, distance, and calories will all count up from zero. OR...
B) SELECT A PROGRAM
1) Select program by pressing the DIRECT BUTTON or using
ARROW key, press ENTER to confirm setting.
2) If needed, select level by pressing UP and DOWN ARROW
KEY, press ENTER to confirm.
3) When setup is complete, press START to begin your workout.
TO CLEAR SELECTION/RESET
THE CONSOLE
Hold STOP key for 3 seconds.
fINISHING YOUR WORKOUT
When your workout is complete, the treadmill will stop and beep. You can turn off the machine or it will enter Energy Saver Mode in
15 mins.
22
PROGRAM INfORMATION
NOTE:
1) If speed or incline are changed during your workout, the remaining segments will be affected accordingly.
2) T81 & T82 contain: calorie goal, weight loss, leg toner & 10K Steps (Note: T81 is without incline changes)
3) T85 contains: calorie goal, weight loss, leg toner, 10K Steps, Strength Builder & MyTrain
4) T86 contains: calorie goal, weight loss, leg toner, 10K Steps, Strength Builder, Half Marathon, Random & MyTrain
1) CALORIE GOAL: Set your target calorie you want to burn today and then the speed desired. Your machine will lead you through a workout joruney and help you complete your task. When you use this program you can adjust your speed and incline level during your workout. The console will automatically transfer to Calories burn and count down from your target calories.
ALL
MODELS
23
ALL
MODELS
24
2) WEIGHT LOSS: Promotes weight loss by increasing and decreasing the speed and incline, while keeping you in your fat burning zone. Speed and Incline changes, segments repeat every 30 seconds.times.
(Metric, km/h)
Segment
Level 1
Time
Incline
Level 2
Level 3
Speed
Incline
Speed
Incline
Level 4
Level 5
Level 6
Level 7
Level 8
Level 9
Level 10
Speed
Incline
Speed
Incline
Speed
Incline
Speed
Incline
Speed
Incline
Speed
Incline
Speed
Incline
Speed
Warm Up
4:00 min
0.0
1.6
0.0
2.0
0.5
0.5
2.4
0.5
3.0
1.0
3.6
1.0
4.1
1.5
4.8
1.5
5.4
2.0
6.0
2.0
6.5
2.5
7.2
2.5
7.8
4.0
1.5
4.4
2.0
4.8
2.0
5.2
2.4
0.5
2.8
1.0
3.2
1.0
3.6
1.5
1 2 3 4 5 6 7 8
30 sec
30 sec
30 sec
30 sec
30 sec
30 sec
30 sec
30 sec
2.5
7.2
2.5
8.0
3.0
8.8
3.0
9.6
1.5
4.0
1.5
4.8
2.0
5.6
2.0
6.4
3.5
10.4
3.5
11.2
2.5
6.4
2.5
7.2
3.0
8.0
3.0
8.8
1.5
3.2
1.5
4.0
2.0
4.8
2.0
5.6
3.5
9.6
3.5
10.4
1.5
8.8
1.5
9.6
2.0
10.4
2.0
11.2
0.5
5.6
0.5
6.4
1.0
7.2
1.0
8.0
2.5
12.0
2.5
12.8
1.5
9.6
1.5
10.4
2.0
11.2
2.0
12.0
0.5
6.4
1.0
7.2
1.0
8.0
1.0
8.8
2.5
12.8
2.5
13.6
1.5
8.8
1.5
9.6
2.0
10.4
2.0
11.2
0.5
5.6
0.5
6.4
1.0
7.2
1.0
8.0
2.5
12.0
2.5
12.8
2.0
8.0
2.0
8.8
2.5
9.6
2.5
10.4
1.0
4.8
1.0
5.6
1.5
6.4
1.5
7.2
3.0
11.2
3.0
12.0
2.0
8.0
2.0
8.8
2.5
9.6
2.5
10.4
1.0
4.8
1.0
5.6
1.5
6.4
1.5
7.2
3.0
11.2
3.0
12.0
2.5
7.2
2.5
8.0
3.0
8.8
3.0
9.6
1.5
4.0
1.5
4.8
2.0
5.6
2.0
6.4
3.5
10.4
3.5
11.2
Cool Down
4:00 min
0.5
3.6
0.5
4.1
1.0
0.0
2.4
0.0
2.8
0.5
3.2
0.5
3.6
1.0
4.0
1.0
4.4
1.5
4.8
1.5
5.2
2.0
5.6
2.0
6.0
7.2
2.0
7.8
2.5
8.4
2.5
8.9
4.8
1.0
5.4
1.5
6.0
1.5
6.5
2.0
Segment
Time
Level 1
Level 2
Level 3
Level 4
Level 5
Level 6
Level 7
Level 8
Level 9
Level 10
Incline
Speed
Incline
Speed
Incline
Speed
Incline
Speed
Incline
Speed
Incline
Speed
Incline
Speed
Incline
Speed
Incline
Speed
Incline
Speed
Warm Up
4:00 min
1.0
2.0
1.0
2.3
1.5
2.5
1.5
2.8
0.0
1.0
0.0
1.3
0.5
1.5
0.5
1.8
2.0
3.0
2.0
3.3
1.5
3.0
1.5
3.4
2.0
3.8
2.0
4.1
0.5
1.5
0.5
1.9
1.0
2.3
1.0
2.6
2.5
4.5
2.5
4.9
1 2 3 4 5 6 7 8
30 sec
30 sec
30 sec
30 sec
30 sec
30 sec
30 sec
30 sec
2.5
4.5
2.5
5.0
3.0
5.5
3.0
6.0
1.5
2.5
1.5
3.0
2.0
3.5
2.0
4.0
3.5
6.5
3.5
7.0
2.5
4.0
2.5
4.5
3.0
5.0
3.0
5.5
1.5
2.0
1.5
2.5
2.0
3.0
2.0
3.5
3.5
6.0
3.5
6.5
1.5
5.5
1.5
6.0
2.0
6.5
2.0
7.0
0.5
3.5
0.5
4.0
1.0
4.5
1.0
5.0
2.5
7.5
2.5
8.0
1.5
6.0
1.5
6.5
2.0
7.0
2.0
7.5
0.5
4.0
1.0
4.5
1.0
5.0
1.0
5.5
2.5
8.0
2.5
8.5
1.5
5.5
1.5
6.0
2.0
6.5
2.0
7.0
0.5
3.5
0.5
4.0
1.0
4.5
1.0
5.0
2.5
7.5
2.5
8.0
2.0
5.0
2.0
5.5
2.5
6.0
2.5
6.5
1.0
3.0
1.0
3.5
1.5
4.0
1.5
4.5
3.0
7.0
3.0
7.5
2.0
5.0
2.0
5.5
2.5
6.0
2.5
6.5
1.0
3.0
1.0
3.5
1.5
4.0
1.5
4.5
3.0
7.0
3.0
7.5
2.5
4.5
2.5
5.0
3.0
5.5
3.0
6.0
1.5
2.5
1.5
3.0
2.0
3.5
2.0
4.0
3.5
6.5
3.5
7.0
(British, MPH)
Cool Down
4:00 min
1.5
3.8
1.5
4.1
2.0
4.5
2.0
4.9
0.5
2.3
0.5
2.6
1.0
3.0
1.0
3.4
2.5
5.3
2.5
5.6
1.0
2.5
1.0
2.8
1.5
3.0
1.5
3.3
0.0
1.5
0.0
1.8
0.5
2.0
0.5
2.3
2.0
3.5
2.0
3.8
*Note: T81 is without incline changes.
3) LEG TONER: Promotes lower body workout and tone your leg by increasing and decreasing the speed and incline. Speed and
Incline changes, segments repeat every 30 seconds. To tone your leg musle you need to workout properly and following guidence below:
1) Streching your leg properly.
2) Start with slow speed and alwasy walk with your heel touching ground softly. (A pair of proper running shoes is recommended)
3) Finish all workout or at least for 30mins.
4) Drink 500-1000 ml. of water slowly after workout.
5) Massage your leg and feet after workout.
6) repeat workout 2-3 times/week and do not over exercise at all time.
ALL
MODELS
Segments
Time
Level 1
Level 2
Level 3
Level 4
Level 5
Level 6
Level 7
Level 8
Level 9
Level 10
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
Warm-Up
4:00 min
1.6
1.6
2.4
2.4
3.2
3.2
4.0
4.0
4.8
4.8
Segments
Time
Level 1
Level 2
Level 3
Level 4
Level 5
Level 6
Level 7
Level 8
Level 9
Level 10
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
Warm-Up
4:00 min
1.0
1.0
1.5
1.5
2.0
2.0
2.5
2.5
3.0
3.0
30
1 sec
2.4
3.2
4.0
4.8
5.6
6.4
7.2
8.0
8.8
9.6
30
2 sec
3.2
4.0
4.8
5.6
6.4
7.2
8.0
8.8
9.6
10.4
30
3 sec
4.0
4.8
5.6
6.4
7.2
8.0
8.8
9.6
10.4
11.2
30
4 sec
4.8
5.6
6.4
7.2
8.0
8.8
9.6
10.4
11.2
12.0
30
5 sec
5.6
6.4
7.2
8.0
8.8
9.6
10.4
11.2
12.0
12.8
30
6 sec
4.8
5.6
6.4
7.2
8.0
8.8
9.6
10.4
11.2
12.0
30
7 sec
4.0
4.8
5.6
6.4
7.2
8.0
8.8
9.6
10.4
11.2
30
8 sec
3.2
4.0
4.8
5.6
6.4
7.2
8.0
8.8
9.6
10.4
30
1 sec
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
30
2 sec
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
30
3 sec
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
30
4 sec
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
30
5 sec
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
30
6 sec
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
30
7 sec
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
30
8 sec
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
(Metric, km/h)
3.2
3.2
4.0
4.0
4.8
4.8
Cool Down
1.6
1.6
2.4
2.4
4:00 min
0.8
0.8
1.6
1.6
1.6
1.6
2.4
2.4
3.2
3.2
(British, MPH)
2.0
2.0
2.5
2.5
3.0
3.0
1.0
1.0
1.5
1.5
Cool Down
4:00 min
0.5
0.5
1.0
1.0
1.0
1.0
1.5
1.5
2.0
2.0
25
ALL
MODELS
4) 10,000 STEPS: Direct key for step-based program. The treadmill will automatically transfer your workout setting into steps taken and help you reach your daily step goal. (See note below for more details).
5) STRENGTH BUILDER (T81 & T82 DOES NOT INCLUDE THIS PROGRAM): Time segments vary from 30 to 90 segments long to challenge your stamina and strength. Time based goal with 10 difficulty levels of incline changes.
Segments
Time
Level 1
Level 2
Level 3
Level 4
Level 5
Level 6
Level 7
Level 8
Level 9
Level 10
Warm-Up
4:00 min
1 1 1 2
1 1 1 2
1 1 1 2
1 1 1 2
1 2 2 2
1 2 2 3
1 2 2 3
1 1 1 2
2 2 2 3
2 3 4 5
1 2 3 4 5 6 7 8 9 10 11 12
30 sec
60 sec
90 sec
60 sec
90 sec
45 sec
60 sec
45 sec
90 sec
90 sec
30 sec
30 sec
2
5
6
3
4
7
2
2
2
2
2
2
2
2
3
4
5
6
7
8
6
7
4
5
8
9
2
2
2
3
1
2
2
3
4
5
5
8
9
10
2
2
3
4
5
5
6
8
10
10
2
3
4
5
5
6
7
9
10
10
1
2
2
3
4
5
5
8
9
9
2
2
3
4
5
5
6
8
9
10
1
2
2
3
4
5
5
8
9
10
2
2
2
3
4
5
6
7
8
9
2
2
2
2
3
4
5
6
7
8
4
5
2
3
6
7
2
2
2
2
Cool Down
4:00 min
2 1 1 1
2 1 1 1
2 1 1 1
2 1 1 1
2 2 2 1
3 2 2 1
3 2 2 1
2 1 1 1
2 1 1 1
3 2 2 1
26
6) HALf MARATHON (T86 ONLY): Distance target program simulates a half marathon training. This program helps tone muscle and improve cardiovascular ability to be ready for a real race.
7) RANDOM (T86 ONLY): Your treadmill will randomly select a program for you. You may press enter to start workout setting or press Random key to select again.
8) MYTRAIN (T85 & T86 ONLY): Machine will automatically record your workout changes every 30 second and you can easily save your favorit setting by pressing MyTrain for 3 seconds and ready for next run. (New record will be replacing old one to keep you on track toward your excellence.
Note:
Steps formula: Calculation based of average stride length of 2.6 feet (0.8 meter / 31 inches)
Steps = distance/average stride length eg: 1mile = 5280 feet (1609 meters) = 5,280/2.6 =2030 steps
BMI TEST:
BMI test direct key to help you gain your BODY MASS INDEX. Input your weight and height after pressing this key.
Your machine will help you calculate your BMI index for furture tracking.
BMI formula:
Kilograms and meters (or centimeters) Formula: weight (kg) / [height (m)]2
Pounds and inches Formula: weight (lb) / [height (in)]2 x 703
Category
Very severely underweight
Severely underweight
Underweight
BMI range – kg/m2 less than 15 from 15.0 to 16.0
from 16.0 to 18.5
Normal (healthy weight)
Overweight
Obese Class I (Moderately obese)
Obese Class II (Severely obese) from 18.5 to 25 from 25 to 30 from 30 to 35 from 35 to 40
Obese Class III (Very severely obese) over 40
Note: BMI classification may vary in different area, above shows the general information from WHO.
For more information feel free to refer to “BMI Classification” from World Health Organization.
ALL
MODELS
27
ALL
MODELS
ENERGY SAVER (STANDBY MODE)
This machine has an energy saver mode. The display will automatically enter standby mode (energy saver mode) after 15 minutes of inactivity and could be waken up with a touch of a button. Entering Energy Saver mode almost all power for the machine will be off except for some circuits that are needed to detect a key press, indicating the console should “wake up”. This feature can be turned off by entering the engineering menu.
To enter the engineering menu, press and hold the incline and speed buttons for 3-5 seconds. (* refer to Note below)
Use incline and speed to navigate through the menu to ENg3. Press ENTER to select. Use incline and speed to select
ENRgY SAVER ON or OFF. Press and hold STOP for 3-5 seconds to exit ENg3. Press and hold STOP again for 3-5 seconds to exit the engineering menu.
28
* Note: T81 is without incline button. You may use Speed up and down to enter ENg mode.
HEART RATE ALERT SYSTEM(T86 ONLY):
Indicator to help monitor your heart rate performance. With your workout start the light will change from warm up, moderate to Fast and Warning mode. Please see below note for more detail information.
Heart rate alert system formula:
LOW (70-90BPM) = blue light,
Moderate (90-120 BPM) = green light,
Mid-fast HR (120-140 BPM) = green light blicking faster,
fast (140-155 BPM)= Red light blicking,
WARNING MODE (Heart rate lower than 70 or higher than 155 BPM) = red light blicking faster with warning sound.
ALL
MODELS
29
T81
Shown
T81 EXPLODED VIEW
25
54
53
11
83
81
46
19
97
49
48
82 A2
26
82
52
A1
13
83
54
17
29
03
A4
56 63
57
55
64
05
84
12
A9 71
63
56
A3
28
39
A15
30
20 78
10
21 78
A16
43
44
18
72
32
73
07
74
A10
08
A13
51
50
A5
45
92 47
04
61
42
41
75
23
37
A11
88 89 90 91
85
24
A12
83
54
A
101
62 60
59
01
35
101
40
A6
33
58
62
A7
27
98
57
22
31 68 54 A14
68
67
80
09
79
67
02
34 36
97 69 95
65
77
15
70
8116
A8
14 70
30
T82 EXPLODED VIEW
25
54
53
11
83
03
A4
56 63
57
29
55
49
46
48
82 A2
26
82
52
A1
13
17
83
54
84
12
A12 71
05
35
01
105
A3
56
61
A5
04
28
39
30
A15
20
78
21 78
10
A16
75
23
37
43
44
18
73
74
45
67 68
69 19
A10
08
A13
24
A14
83
76
38
97
54
A17
A
51
50
54
75
22
31
86 54 A18
86
85
80
09
79
85
34 36
02
100 69 15
77
70
16
82
92 47
A6
105
62
60 59
58 62
A7
27
102
57
A8
33
40
65
66
06
A9
64 42
41
A11
14
70
88 89 90 91
T82
Shown
31
T85
Shown
T85 EXPLODED VIEW
32
NO.
1
B19
B23
B26
B27 aN5 aR1 aR2
B19
6 aB1 ah1 am1
4
5
2
3
B39
B40
B41
B42
B43
B31
B33
B37
B38
DESCRIPTION
CONSOlE maST SET;SEmI-aSSy;lEfT;Tm466;
CONSOlE maST SET;SEmI-aSSy;RIghT;Tm466
BaSE SET;SEmI-aSSy;Tm466;
DRIVE mOTOR SET;SEmI-aSSy;Tm327E;
CONSOlE SET;SEmI-aSSy;Tm466;
COVER SET;SEmI-aSSy;uP;mOTOR;Tm466; maIN BaSE TuBE-ExTRawORk;fRamE;SCREEN P
PaINTINg;ElEVaTION RaCk SET;ROhS ;Sl;a mOTOR SuPPORT fRamE;PaINTINg;ROhS;Sl;aZ
SEmI-aSSy;SafETy SwITCh SET;Tm196-1uS; fRONT ROllER SET-820,830T
ROllER SET;REaR;Tm196
SCREw;fh;m8x1.25Px28l;hS;BP
NuT;Nlk;m8x1.25P;BaN;
SCREW;BH;Φ4X12L;SM;PH;BAN;POT
SPEED SENSOR fIx PlaTE; al fINIShED TREaDmIll DECk;607x1133x15T;SI aIR STICk;SlOw-DROP;30kg;425.0-690.0;
NuT;NylON;m8x1.25P;CR;
WASHER;FLT;Φ10.5XΦ25.0X1.5T;TFN; fIxINg PlaTE;-;f;PaINTINg;Tm327;SPhC
SCREW;TRH;Φ4X12L;SM;PH;BAN;POT
TaPE;fOam;SINglE-SIDE;20x300x1.0T;Tm396 flaT;PVC;Tm291-B17a
SCREw;Bh;m8x1.25Px30l;hS;BP
WASHER;FLT;Φ8.1X20X1.0T;TFN;
NO.
B45 l06 m02 m07 m08 k09 k14 k15 k23 h07 h08 k06 k08
B61
B64
C17 h06 m15 m16 m18 m20 m21 m11 m12 m13 m14
DESCRIPTION
ShIm;DECk;NR;yEllOw;10x20x2.0;Tm466;ElE fIxPIECE;SIDE RaIl;Tm187-141a-00
SCREW;FH;Φ5X15L;SM;PH;BAN;POT
CAP;PP;BL;ARM REST;Φ30XΦ60;TM420-2KM;
SCREw;SPECIal;m8x1.25Px9l-D10x9.5l;hEx
NuT;NylON;m8x1.25P;CR;
WASHER;FLT;Φ10.5XΦ20.0X1.0T;TFN; waShER; fRONT lEVElER fOOT;BaSE;PVC;3/8-16uNC;BlaCk;Tm616
SCREw;Bh;m10x1.5Px50l-15l;hS;Chm;P-T
NuT;Nlk;m10x1.5P;Chm; flaT;60C;Tm196-k12B
TRaNSPORT whEElS;-;Tm196; mCB;mlh1102hgPg;1.5-2.0hP;220V lIfT mOTOR;aC;220V;500lBS;-;58mm;210mm;1
SCREw;Sh;m8x1.25Px45l-30l;hS;BZN;g12.9;
SCREw;Sh;5/16-18uNCx14l;hS;BP
WASHER;FLT;Φ10.5XΦ18.0X2.0T;BAN;
WASHER;SPL;Φ10.2XΦ18.4X2.5T;BOX;
NuT;Nlk;m8x1.25P;BZN;
SCREw;hh;3/8-16uNCx55l-14l;hE;P-T
SCREw;hh;3/8-16uNC-42l-14l;hE;P-T
NuT;Nlk;3/8-16uNC;BaN;
ElaSTOmER;Tm196;Tm196-m20a
SCREw;m8x1.25Px9l-D10x9.5l;hE;45#;BOx;
T85
Shown
33
T85
Shown
34
NO.
m23
P19
P20
P21
P22
P12
P14
P15
P18
P02
P03
P07
P08 m24 m25 m26
P01
P30
P30
P30
P30
P30
P23
P30
P30
P30
DESCRIPTION
SCREW;BH;Φ4X12L;SM;PH;YZN;POT
WASHER;FLT;Φ8.4XΦ15.5X1.6T;BZN;
WASHER;SPL;Φ8.2XΦ15.4X2.0T;
WASHER;FLT;Φ8.2XΦ20.0X3.0T;
SwITCh;POwER;kCD3;Tm196;Tm196-P01a
POwER SOCkET SET;-;CE(80,800,300);16awg
CONSOlE wIRE;D;1800l;Ckm2.5-9P+Sm-9a;Tm4 wIRE;Sf CON;BlaCk;250lOCk300l 16awg; wIRE;BS CON;BlaCk;250lOCk2 60l;
BREakER;ThROugh ElECTRIC CuRRENT;7a 250V
SENSOR;-;-;1000mm(Ckm 25430101-03);Tm394
SCREW;BH;Φ3X8L;SM;PH;WZN;POT
SCREw;Bh;m5x0.8Px25l;CT;PS;Nkl;
NuT;hx;m5x0.8P;SS41;Nkl;
WASHER;TOOTH;Φ5.3XΦ10.0X0.6T;BAN;
WAVE TUBE; CR-11SP;Φ14XΦ10.7;200M/COiL
SCREw;fh;m3x0.5Px10l;Ph;ZN;
NuT;hx;m3x0.5Px3h;SS41;Chm;
ExTERNal PwR;IN;-;-;1.5mm;2m;-;-
ExTERNal PwR;NEw ZEalaND;-;-;1.5mm;2m;-;
ExTERNal PwR;EuROPE;-;-;1.5mm;2m;-;-
ExTERNal PwR;ChINa;-;-;-;1.5mm;-;2m
ExTERNal PwR;hk/kw/gB;-;-;1.5mm;2m;-;-
ExTERNal PwR;uS/Ca/Th;16awg;2m
ExTERNal PwR;aRgENTINa;-;-;1.5mm;2m;-;-
ExTERNal PwR;SOuTh afRICa;-;-;-;1.5mm;-;
NO.
P30
R05
R06
R07
V02
Q13
Q15
R03
R04
Z01
Z02
Z03
Z04
Z05
Q03
Q09
Q10
Q11
P30
P30
P30
Q02
DESCRIPTION
ExTERNal PwR;SwEDEN;2m;1.5mm
ExTERNal PwR;BR;lENgTh:2m;1.5mm2
ExTERNal PwR wIRE SET;ISRaEl;-;-;1.5mm;2 wIRE;ExTERNal PwR;SET;ChIlE uSED;JIS2 u
COVER;mOTOR;DOwN;PP;BlaCk;Tm196;
SIDERaIl;COVER;PahS;Tm396
END CaP;fRamE;lEfT-REaR;aBS(Pa-756);7514
END CaP;fRamE;RIghT-REaR;aBS(Pa-756);751
SCREW;BH;Φ4X12L;SM;PH;BAN;POT
SCREW;TRH;Φ4X15L;SM;PH;BAN;POT
STiCKER;ANTi-SKid ；TM283
R-BElT;PahS;458x2552x1.4T;Tm327
BElT;POly-V;170-J5;
SCREw;Sh;m8x1.25Px40l;hS;
SCREw;Bh;m8x1.25Px55l;hS;BaN;f-T
WASHER;FLT;Φ8.4XΦ15.5X1.6T;BZN;
DECORaTED laBEl;fRamE;VCS lITE;Tm466
SCREw;BuTTON hEaD;m8x1.25Px55l-20l;hEx
SCREw;Bh;m8x1.25Px20l;hS;Chm;
WASHER;ARC;Φ8.4XΦ17.0X1.0T;CHM;
WASHER;SPL;Φ 8.2XΦ15.4X2.0T;CHM;
WASHER;FLT;Φ8.2XΦ15.0X1.2T;CHM;
SIlICON OIl BOTTlE;50ml;OIl CONTENT 40ml
DOCumENTaTION;maNual;Tm SafETy DIRECTION
DOCumENTaTION;maNual;uSE maNIPulaTE;T haRDwaRE SET;Tm466;
N09
N10
N20
N22 k10 aN1
N01
N02
Q12 aC2
Q12 ak1 m03 m06 m22 aC1
N35
N36
N61
N62
N23
N25
N26
N33
NO.
DESCRIPTION wRENCh;hEx;T-TyPE;#5x172l; wRENCh;hEx;l-TyPE;m5x110l; mOTOR;1.5hP/180V flywhEEl; mOTOR;Tm196;Tm196-m02E; fERRITE CORE
CONSOlE maST SET;l;PaINTINg;SIlVER3;Tm
FOAM;Φ30XΦ60X3.0TX360L;ARM REST;TM466
CONSOlE maST SET;R;PaINTINg;SIlVER3;Tm
FOAM;Φ30XΦ60X3.0TX360L;ARM REST;TM466
BaSE fRamE SET;PaINTINg;SIlVER3;Tm466
RVN;alS7-616-150(0.02-0.15);yZN;
BaSE SET;CONSOlE;PaINTINg;SIlVER3;Tm46
CONSOlE BaSE CaSINg;CONSOlE;hIPS;75140;
OVERlay;CONSOlE;PaINTINg;877C;BRIghT SI
SCREW;BH;Φ4X12L;SM;PH;BAN;POT
SafETy kEy SENSOR wIRE;300l
CONSOlE wIRE;u;450l;Ckm2.5-9P+Sm-9y;Tm40
CONNECT wIRE;VIDEO-hEaD PhONE;2*(2.54-3P
THREE-d EARPHONE WiRE;PJ-2030T(SOCKTE Φ3
(uP)CONTROl PaNEl;hDPD;S101-01;CITTaT auDIO INPuT BOaRD-T83,84
SCREW;BH;Φ3X8L;SM;PH;BAN;POT
SENSOR SET;PULSE;800MM(Φ31.8+2.5-2P JiNd
SCREW;BH;Φ4X8L;SM;PH;YZN;POT
DOCumENTaTION;CTl OVERlay;DISPlay maNIPu kEyPaD;mEmBRaNE;D;Tm466-2km;Tm466-N62
NO.
N79
N90
V39
Q01
V04
DESCRIPTION
WiRE;GRiP PULSE;250+Φ6 ;500;TM219;TM2 aBSORPTION PlaTE;15x15;Tm616 waRNINg STICkER;OVERlay;REmOVE PROTECTIV
TIE STRaP aDhESIVE; NylON66;hC-101;w fIx ImPlEmEN;hw-8aa
CaBlE TIE;NylON;BlaCk;160l mOTOR COVER;uP;hIPS;75140;Tm466; lOgO laBEl;mOTOR COVER;TEmPO;Tm466
T85
Shown
35
T86
Shown
T86 EXPLODED VIEW
36
NO.
1
B23
B26
B27
B31 aR1 aR2
B19
B20 aB1 ah1 am1 aN5
5
6
2
4
B42
B43
B45
C17
C17
B33
B37
B40
B41
DESCRIPTION
CONSOlE maST SET;SEmI-aSSy;lEfT;Tm472;
CONSOlE maST SET;SEmI-aSSy;RIghT;Tm472
DRIVE mOTOR SET;SEmI-aSSy;Tm327E;
CONSOlE SET;SEmI-aSSy;Tm472;
COVER SET;SEmI-aSSy;uP;mOTOR;Tm466; fRamE SET;PaINTINg;SIlVER3;Tm466;
PaINTINg;ElEVaTION RaCk SET;ROhS ;Sl;a mOTOR SuPPORT fRamE;PaINTINg;ROhS;Sl;aZ
SEmI-aSSy;SafETy SwITCh SET;Tm196-1uS; fRONT ROllER SET-820,830T
ROllER SET;REaR;Tm196
SCREw;fh;m8x1.25Px28l;hS;BP
NuT;Nlk;m8x1.25P;BaN;
SCREW;BH;Φ4X12L;SM;PH;BAN;POT
SPEED SENSOR fIx PlaTE; al fINIShED TREaDmIll DECk;607x1137x15T;Na aIR STICk;SlOw-DROP;30kg;425.0-690.0;
NuT;NylON;m8x1.25P;CR;
WASHER;FLT;Φ10.5XΦ25.0X1.5T;TFN;
TaPE;fOam;SINglE-SIDE;20x300x1.0T;Tm396 flaT;PVC;Tm291-B17a
SCREw;Bh;m8x1.25Px30l;hS;BP
WASHER;FLT;Φ8.1X20X1.0T;TFN;
ShIm;DECk;NR;yEllOw;10x20x2.0;Tm466;ElE
CAP;PP;BL;ARM REST;Φ30XΦ60;TM420-2KM;
POwER SOCkET SET;-;CE(80,800,300);16awg
NO.
h06 m11 m12 m13 m14 l06 m02 m07 m08 k09 k14 k15 k23 h07 h08 k06 k08 m21 m23 m24 m25 m26 m15 m16 m18 m20
DESCRIPTION
SCREw;SPECIal;m8x1.25Px9l-D10x9.5l;hEx
NuT;NylON;m8x1.25P;CR;
WASHER;FLT;Φ10.5XΦ20.0X1.0T;TFN; waShER; fRONT lEVElER fOOT;BaSE;PVC;3/8-16uNC;BlaCk;Tm616
SCREw;Bh;m10x1.5Px50l;hS;
NuT;Nlk;m10x1.5P;BaN; flaT;60C;Tm196-k12B
TRaNSPORT whEElS;-;Tm196; mCB;mlh1102hgPg;1.5-2.0hP;220V lIfT mOTOR;aC;220V;500lBS;-;58mm;210mm;1
SCREw;Sh;m8x1.25Px45l-30l;hS;BZN;g12.9;
SCREw;Sh;5/16-18uNCx14l;hS;BP
WASHER;FLT;Φ10.5XΦ18.0X2.0T;BAN;
WASHER;SPL;Φ10.2XΦ18.4X2.5T;BOX;
NuT;Nlk;m8x1.25P;BZN;
SCREw;hh;3/8-16uNCx55l-14l;hE;P-T
SCREw;hh;3/8-16uNC-42l-14l;hE;P-T
NuT;Nlk;3/8-16uNC;BaN;
ElaSTOmER;Tm196;Tm196-m20a
SCREw;m8x1.25Px9l-D10x9.5l;hE;45#;BOx;
SCREW;BH;Φ4X12L;SM;PH;YZN;POT
WASHER;FLT;Φ8.4XΦ15.5X1.6T;BZN;
WASHER;SPL;Φ8.2XΦ15.4X2.0T;
WASHER;FLT;Φ8.2XΦ20.0X3.0T;
T86
Shown
37
T85
Shown
38
NO.
P01
P30
P30
P30
P30
P20
P21
P22
P23
P14
P15
P18
P19
P03
P07
P08
P12
P30
P30
P30
P30
Q02
P30
P30
P30
P30
DESCRIPTION
SwITCh;POwER;kCD3;Tm196;Tm196-P01a
CONSOlE wIRE;D;1800l;Ckm2.5-9P+Sm-9a;Tm4 wIRE;Sf CON;BlaCk;250lOCk300l 16awg; wIRE;BS CON;BlaCk;250lOCk2 60l;
BREakER;ThROugh ElECTRIC CuRRENT;7a 250V
SENSOR;-;-;1000mm(Ckm 25430101-03);Tm394
SCREW;BH;Φ3X8L;SM;PH;WZN;POT
SCREw;Bh;m5x0.8Px25l;CT;PS;Nkl;
NuT;hx;m5x0.8P;SS41;Nkl;
WASHER;TOOTH;Φ5.3XΦ10.0X0.6T;BAN;
WAVE TUBE; CR-11SP;Φ14XΦ10.7;200M/COiL
SCREw;fh;m3x0.5Px10l;Ph;ZN;
NuT;hx;m3x0.5Px3h;SS41;Chm;
ExTERNal PwR;IN;-;-;1.5mm;2m;-;-
ExTERNal PwR;NEw ZEalaND;-;-;1.5mm;2m;-;
ExTERNal PwR;EuROPE;-;-;1.5mm;2m;-;-
ExTERNal PwR;ChINa;-;-;-;1.5mm;-;2m
ExTERNal PwR;hk/kw/gB;-;-;1.5mm;2m;-;-
ExTERNal PwR;uS/Ca/Th;16awg;2m
ExTERNal PwR;aRgENTINa;-;-;1.5mm;2m;-;-
ExTERNal PwR;SOuTh afRICa;-;-;-;1.5mm;-;
ExTERNal PwR;SwEDEN;2m;1.5mm
ExTERNal PwR;BR;lENgTh:2m;1.5mm2
ExTERNal PwR wIRE SET;ISRaEl;-;-;1.5mm;2 wIRE;ExTERNal PwR;SET;ChIlE uSED;JIS2 u
COVER;mOTOR;DOwN;PP;BlaCk;Tm196;
NO.
Q05
R05
R06
R07
Z01
Q16
Q17
R03
R04
Z02
Z03
Z04
Z05
Q11
Q13
Q14
Q15
Q06
Q08
Q09
Q10
DESCRIPTION
SIDE RaIl-ExTRawORk;lEfT;SCREEN PRINT;
SIDE RaIl-ExTRawORk;RIghT;SCREEN PRINT;
DECORaTE PlaTE;fRamE;NR;ORaNgE;Tm472;
COVER;SIDE RaIl;lEfT;PP;75140;Tm472;
COVER;SIDE RaIl;RIghT;PP;75140;Tm472;
SCREW;BH;Φ4X12L;SM;PH;BAN;POT
SCREW;TRH;Φ4X15L;SM;PH;BAN;POT
SCREW;TRH;Φ4X12L;SM;PH;BAN;POT
WASHER;FLT;Φ6.5XΦ14.0X1.0T;BZN;
Plug;SCREw;NR;BlaCk;Tm472;
SCREW;BH;Φ4X15L;TC;PH;BAN;POT
R-BElT;PahS;458x2552x1.4T;Tm327
BElT;POly-V;170-J5;
SCREw;Sh;m8x1.25Px40l;hS;
SCREw;Bh;m8x1.25Px55l;hS;BaN;f-T
WASHER;FLT;Φ8.4XΦ15.5X1.6T;BZN;
SCREw;BuTTON hEaD;m8x1.25Px55l-20l;hEx
SCREw;Bh;m8x1.25Px20l;hS;Chm;
WASHER;ARC;Φ8.4XΦ17.0X1.0T;CHM;
WASHER;SPL;Φ 8.2XΦ15.4X2.0T;CHM;
WASHER;FLT;Φ8.2XΦ15.0X1.2T;CHM;
SIlICON OIl BOTTlE;50ml;OIl CONTENT 40ml
DOCumENTaTION;maNual;Tm SafETy DIRECTION
DOCumENTaTION;maNual;uSE maNIPulaTE;T haRDwaRE SET;Tm466; wRENCh;hEx;T-TyPE;#6x167l;
g10
Q12 aC2 g04 g03 g05 g07 g08 k10
Q01
V04 aC1 m03 m06 m22 ak1
Q12 aN1
N01
N02
N03 g05 g07 g08 g11
NO.
DESCRIPTION wRENCh;hEx;l-TyPE;m5x110l; mOTOR;1.5hP/180V flywhEEl; mOTOR;Tm196;Tm196-m02E; fERRITE CORE
BaSE fRamE SET;PaINTINg;SIlVER3;Tm466
RVN;alS7-616-150(0.02-0.15);yZN; mOTOR COVER;uP;hIPS;75140;Tm466; lOgO laBEl;mOTOR COVER;TEmPO;Tm466
CONSOlE maST SET;l;PaINTINg;Sl;Tm472;
COVER-ExREawORk;QuICk kEy;lEfT;SCREEN PR
RuBBER kEy;aRm REST;SIlICa;ORaNgE;Tm47
SCREW;TRH;Φ4X12L;SM;PH;BAN;POT
SCREW;BH;Φ3X8L;TC;PH;BZN;FLT
CONNECT BOaRD;QuICk kEy;INClINE;ha;Pa;
FOAM;Φ30XΦ60X3.0TX360L;ARM REST;TM472
CONSOlE maST SET;R;PaINTINg;Sl;Tm472;
COVER-ExREawORk;QuICk kEy;RIghT;SCREEN P
RuBBER kEy;aRm REST;SIlICa;ORaNgE;Tm47
SCREW;TRH;Φ4X12L;SM;PH;BAN;POT
SCREW;BH;Φ3X8L;TC;PH;BZN;FLT
CONNECT BOaRD;QuICk kEy;SPEED;ha;Pa;SO
FOAM;Φ30XΦ60X3.0TX360L;ARM REST;TM472
BaSE SET;CONSOlE;PaINTINg;SIlVER3;Tm46
CONSOlE BaSE CaSINg;CONSOlE;hIPS;75140;
OVERlay;CONSOlE;PaINTINg;877C;BRIghT SI fIxINg BOx;CONSOlE BaSE COVER;NR;75140;
NO.
N09
N35
N36
N61
N62
N79
N90
V39
N25
N26
N30
N33
N10
N20
N22
N23
DESCRIPTION
SCREW;BH;Φ4X12L;SM;PH;BAN;POT
INDuCTION wIRE;SafETy SwITCh;220(OkI mag
CONSOlE wIRE;u;450l;Ckm2.5-9P+Sm-9y;Tm40
CONNECT wIRE;VIDEO-hEaD PhONE;2*(2.54-3P
THREE-d EARPHONE WiRE;PJ-2030T(SOCKTE Φ3
(uP)CONTROl PaNEl;hDPD;S101-01;CITTaT auDIO INPuT BOaRD-T83,84 aRm REST QuICk kEy CONNECTINg wIRE; uPPE
SCREW;BH;Φ3X8L;SM;PH;BAN;POT
SENSOR SET;PULSE;800MM(Φ31.8+2.5-2P JiNd
SCREW;BH;Φ4X8L;SM;PH;YZN;POT
DOCumENTaTION;CTl OVERlay;DISPlay maNIPu kEyPaD;mEmBRaNE;D;NT941-03;Tm472-N62;
WiRE;GRiP PULSE;250+Φ6 ;500;TM219;TM2 aBSORPTION PlaTE;15x15;Tm616 waRNINg STICkER;OVERlay;REmOVE PROTECTIV
TIE STRaP aDhESIVE; NylON66;hC-101;w fIx ImPlEmEN;hw-8aa
CaBlE TIE;NylON;BlaCk;160l
T85
Shown
39
ALL
MODELS
D: Entsorgungshinweis
Horizon Fitness - Produkte sind recyclebar. Führen Sie das gerät am Ende der Nutzungsdauer einer sachgerechten
Entsorgung zu (örtliche Sammelstelle).
GB: Waste Disposal
Horizon Fitness products are recyclable. At the end if its useful life please dispose of this article correctly and safely
(local refuse sites).
f: Remarque relative à la gestion des dèchets
Horizon Fitness sont recyclables. A la fin sa durrèe d`utilisation, remettez I´appareil à un centre de gestion de dèchets correct (collecte locale).
NL: Verwijderingsaanwijzing
Horizon Fitness producten zijn recycleerbaar. Breng het apparaat aan het einde van de gebruiksduur naar een op recycling gespecialiseerd bedrijf (plaatselijk verzamelpunt).
E: Informaciones para la evacuaciòn
Los productos de Horizon Fitness son riciclables. Cuando se termina la vida ùtil de un aparato o una màquina, entrèguelos an una impresa local de eleiminaciòn de residuos para su reciclaje.
I: Indicazione sullo smaltimento
I prodotti Horizon Fitness sono reciclabill. Quando I`apparecchio non servirà più, portatelo in un apposito punto di raccolta della Vostra città (Punti di raccolta comunall).
PL: Wskazòwka dotyczàca usuwania odpadòw.
Producty firmy Horizon Fitness podlegajà recyklingowi. Pod koniec okresu o`ywalnoÈcl pros`z oddac urzàdzenie do wlaÈciwego punkto usuwania odpadòw (lokalny punkt zbiorczy).
40
TREADMILL OWNER’S MANUAL
T81 T82 T85 T86 Owner’s Manual 070213’ Rev. 1 ©2013 Tempo Fitness
advertisement
Related manuals
advertisement