Quick Installation Guide Applicable model: LDV-212ASK

KVM Switching Client Software for Windows/Mac

User-definable Hotkeys

Independent/Simultaneous Audio&PC Switching

Autoscan Delay Time Programmable

LDV-212ASK

2-port Compact Desktop

DVI USB KVM Switch w/ Audio&Mic

Quick Installation Guide

Thank you for purchasing the LDV-212ASK Compact Desktop

DVI USB KVM Switch ! With our highly reliable and quality product, user can enjoy countless benefits from using it.

Step 1.

Insert the companion CD ROM into your CD drive, and the Autorun screen will pop up (If the Autorun feature has not been enabled on your computer. Just find the

Autorun.exe on the CDROM and double-click it to start).

LDV-212ASK

Introduction

The LDV-212ASK is a 2-port Slim Palmtop USB KVM Switch with audio and microphone switching function. It allows you to access, control, boot and reboot 2 DVI-enabled USB multimedia computers. The independent audio/mic switching function allows an uninterrupted audio experience on a same connected computer even when you switch to another computer.

This KVM Switch adopts the DVI technology for digital video signal transmission over the cable to reduce undesired distortion from conventional analog/digital conversion. Both digital video

(1920 x 1200) and analog video (2048 x 1536) are supported.

For Windows and Mac platforms, it provides an innovative and easy-to-use KVM Switcher Software -- a small windows client application to facilitate your KVM switching operations such as

PC selection and hotkey sequence programming, autoscanning, autoscan delay time programming, independent/simultaneous audio&PC switching, etc.

Out-of-the-box Installation

Take the Companion CDROM and the KVM Switch out of the box and follow the steps below for installation….

Step 2.

For Windows/Mac : Just click the “Software Installation for Window/Mac” to start installation. (If the Mac version software does not start, you should then copy it to your local Hard disk on Mac). Follow the instructions to completion. If the installation is complete, you will see a

KVM Switcher icon on the system tray of your desktop.

Right-click to evoke the operation menu and doubleclick to evoke the configuration box. For operation details of the KVM Switcher software, please refer to the

Operation Quick Reference.

The Windows switcher software is recommended for use on

Windows 98 SE or later. The Mac switcher software is recommended for use on Mac OS 10.4 [Tiger].

Windows Mac OS

No live connection detected

Current active PC channel is on port 1

Current active PC channel is on port 2

The KVM Switcher Software supports both the Windows and the

Mac OS operating systems. For other OS platforms such as Linux, you can still use the keyboard hotkey - ScrLk + ScrLK - to switch PC.

However, this switching hotkey is not available on non-PC platform such as MacOS.

Step 3.

Plug in the Power adapter to the Power receptacle on the backpanel . Then connect the shared USB keyboard, mouse, monitor, speaker/headphone and microphone each to its port on your KVM Switch.

Step 4 . Connect each KVM PC port to a computer, using the slim 3-in-1 KVM combo cable and the audio/mic cable.

After you have connected the KVM and computers properly, you can operate the KVM Switch immediately.

If you need to connect a computer with an analog video display

(HDB15) to the KVM switch, you need to use a HDB15-DVI adapter for connection.

Some older computers with USB interface might need to manually enable the USB option in the BIOS settings before you can use any

USB devices. If your USB interface does not work, please check the

USB option in the BIOS.

If you use Windows 95/98/SE or Mac OS and has not yet installed a

USB mouse on your computer, there might be an error message telling you that mouse is not detected and prompting you to decide whether to ignore the same message in the future, and yet you will find there is no mouse movement to disable this message….So it is suggested that you should installed your USB mouse on your computer first, before connecting it to this KVM Switch.

Sharing High-speed USB Device

The 2 USB ports on the front-panel are normally used for keyboard and mouse connections. However, they are USB 2.0 hub ports and can also be connected to any USB devices so that you can easily switch and share the USB devices among two computers.

Rev. 1.3 Copyright© All rights reserved

Quick Installation Guide Applicable model: LDV-212ASK

Easy Operation

There are three methods to control your KVM Switch for PC and

Audio/Mic channel selection: using (1) the face-panel push buttons, (2) the hotkey sequences, or (3) the KVM Switcher

Software.

Face-panel buttons

The face-panel button allows you a direct control over KVM switching operation. Simply press the button to switch to the corresponding PC port (and audio/mic channel, if binding is enabled). By default, PC port switching and audio/mic port switching are bound together, unless you specify the audio to be fixed a specific port.

You can use the face-panel button to switch to an empty port that is not connected with any computer. Normally, if you use keyboard hotkeys or the KVM Switcher software, you will not be able to switch to an empty port.

Keyboard hotkeys

User-definable hotkeys for PC selection:

Hotkey sequence = Ctrl - Alt - [command key]*

* Please refer to next section for keys that are qualified to be used as a command key

Note that these 3 keys should be pressed and held together. And it is upon the release of all three keys, the switching action will be executed.

Universal hotkey for switching to next port:

Universal Hotkey sequence = ScrLk + ScrLk

* For other operating systems on PC such as Linux, you can still use this special hotkey to facilitate PC switching. This special hotkey is not available for Mac.

Both the universal hotkey, ScrLk + ScrLk and the user-definable hotkey, Ctrl - Alt - [command key] WILL NOT allow you to switch to an empty port that is not connected with any computer. To force your KVM to switch to an empty port, just press the face-panel button to switch.

Each keystroke within a hotkey sequence should be pressed within

2 seconds. Otherwise, the hotkey sequence will not be validated.

After port switching, you have to wait till the KVM Switcher icon shows forth the target port before you can perform next switching again.

All the hotkeys are only functional after your PCs are booting into the OS. If you want to switch PC in the BIOS/preboot stage, press the face-panel button to switch.

KVM Switcher Software

In addition to PC switching, the KVM Switcher Software also allows you more advanced functions such as described in the next section….

KVM Switcher Operation Reference

Switch to PC x by Operation Menu

Right-click the KVM Switcher icon to evoke the operation menu, then select whichever PC that is available for switching. Once you select a PC channel, it will immediately switch to that PC.

Note that the unconnected port(s) or the active port will be grayed-out and hence non-selectable.

Note that these 3 keys should be pressed and held together. And it is upon the release of all three keys, the switching action will be executed.

Start Auto-scan

Right-click the KVM Switcher icon to evoke the operation menu, then select Start Auto-Scan to activate autoscanning.

Stop Auto-scan

(While autoscanning) Press any key on keyboard, or press any button on the front-panel will stop autoscan.

While autoscanning, the mouse will be locked and hence not possible to stop autoscan by the menu option.

KVM Switcher configuration

Right-click the KVM Switcher icon and select Settings or doubleclick the icon to bring up the configuration dialog box.

Define Hotkey commands

You can specify the command key as you like by typing it in. For example, you can specify the hotkey for switching to PC 1 as

CTRL - ALT - A by typing an A (not case-sensitive) in the editable field.

Hotkey Sequence = CTRL - ALT - [command key]*

* The command key is user-definable via the configuration dialog box

Please note that if you intend to modify the command key, you have to modify them on each and every of the connected computers, since the hotkey setting is stored within each connected computer.

Windows : Operation Menu Configuration Dialog Box

Mac OS: Operation Menu Configuration Dialog Box

Switch to PC x by Keyboard Hotkeys

Hit the hotkey according to your current hotkey definition:

Hotkey sequence = Ctrl - Alt - [command key]*

* The factory default hotkey setting is Ctrl + Alt + 1/2/3/4 for PC 1/2/3/4. You can also use ScrLk + ScrLk to switch PC.

Except those control keys such as Alt, Ctrl, Shift, CAPS, Tab, Esc and those functions keys and edit keys, all other keys on the keyboard, including those number keys on the number pad, are all other keys qualified to be used as hotkey command keys. In addition to the software

KVM Switching by the operation menu and the user-defined hotkeys, you can always use the universal hotkey for PC switching – ScrLk + ScrLk

Turn On Buzzer

Check this option to turn on the buzzer sound.

Fix Audio Port at PC x

Check this option and then select the PC to fix the audio/mic channel to the selected PC. Once this option is checked, the audio/mic channel will be fixed and become non-switchable.

Auto Scan Period

Select the Autoscan period from 10 ~ 60 seconds with an increment of 5 seconds. The Autoscan period is the time your

KVM Switch will wait before switching to next PC.

Technical Support

E-mail: [email protected]

Website: www.linkskey.com

Rev. 1.3 Copyright© All rights reserved