User's Guide

WorkFit-S, Dual

CAUTION: DO NOT EXCEED MAXIMUM LISTED

WEIGHT CAPACITY. SERIOUS INJURY OR

PROPERTY DAMAGE MAY OCCUR!

A

6 - 14 lbs

(2.7-6.4 kg)

B

6 - 14 lbs

(2.7-6.4 kg)

C

< 5 lbs

(2.3 kg)

D

< 5 lbs

(2.3 kg)

A

+

B

+

C

+

D < 25 lbs (11.3 kg)

For the latest User Installation Guide please visit: www.ergotron.com

User's Guide - English

Guía del usuario - Español

Manuel de l’utilisateur - Français

Gebruikersgids - Deutsch

Benutzerhandbuch - Nederlands

Guida per l’utente - Italiano

Användarhandbok - svenska

ユーザーガイド : 日本語

用户指南 : 汉语

888-33-332-W-02 rev.G • 03/15

Includes

Constant Force™

Technology

1 of 11

Hazard Symbols

Review

These symbols alert users of a safety condition that demands attention. All users should be able to recognize and understand the signifi cance of the following Safety Hazards if encountered on the product or within the documentation. Children who are not able to recognize and respond appropriately to

Safety Alerts should not use this product without adult supervision!

Symbol Signal Word

NOTE

CAUTION

WARNING

ELECTRICAL

Level of Hazard

A NOTE indicates important information that helps you make better use of this product.

A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

A WARNING indicates either potential for property damage, personal injury, or death.

An Electrical indicates an impending electrical hazard which, if not avoided, may result in personal injury, fi re and/or death.

Safety

Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or diffi cult or if product does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements. Depending on your product and the adjustment, it may take many turns to notice a difference. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.

Warning: Because mounting surface materials can vary widely, it is imperative that you make sure mounting surface is strong enough to handle mounted product and equipment.

Caution:

To avoid the potential to pinch cables it is important to follow the cable routing instructions in this manual. Failure to follow these instructions may result in equipment damage or personal injury.

2 of 11

888-33-332-W-02 rev.G • 03/15

Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or diffi cult or if product does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements. Depending on your product and the adjustment, it may take many turns to notice a difference. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.

GREEN ARROWS MARK IMPORTANT ADJUSTMENT POINTS

1

Follow Steps 1 - 7 for Installation

4

2

After installation, adjust product to properly handle added weight.

10

To view a video on this adjustmen t procedure, go to install.ergotr

on.com

11

3 of 11

888-33-332-W-02 rev.G • 03/15

1

2

3

4

1x

5

6

1x

7

2x

Components

A

1x

3x

4x

2x

2x

2x

12x

8x

B

Features & Specifi cations

M5 x 14mm

M6 x 6mm

M5 x 12mm

M4 x 5mm

M4 x 10mm

18"

(45.7 cm)

10

9

8

3x

2x

1x

4x

2x

1x

M4 x 10mm

M4x12mm

M4 x 8mm

4mm

68˚

4.8"

(122 mm)

11

1x

13

12

1x

1x

3x

1x

1x

3mm

1x

Tools Needed

14mm

7.5˚

4 of 11

888-33-332-W-02 rev.G • 03/15

1

4mm

4x

M6 x 6mm

3mm

3x

M5 x 14mm

2

4mm

0.47" - 1.38" (12 - 35 mm) 1.46" - 2.4" (37 - 60 mm)

1 2

888-33-332-W-02 rev.G • 03/15

5 of 11

3

2x

M5 x 12mm

4 a

2x

1x b c

6 of 11

888-33-332-W-02 rev.G • 03/15

5 a

4x

M4x10mm

b

4x

M4x12mm

6

7

4x

M4 x 10mm

4x

M4 x 10mm

0°

3.5˚ 8.5˚

2x

M4 x 8mm

7 of 11

888-33-332-W-02 rev.G • 03/15

8

1x

M4 x 5mm

2x

1x

M4 x 5mm

Center total width of mounted equipment on stand.

9

2x

1x

3x

8 of 11

2x

888-33-332-W-02 rev.G • 03/15

10

Adjustment Step

Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or diffi cult or if product does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements.

Depending on your product and the adjustment, it may take many turns to notice a difference. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.

A

14mm

Increase Lift Strength

If the mounted weight is too heavy or this product does not stay up when raised, then you'll need to increase

Lift Strength:

Decrease Lift Strength

If the mounted weight is too light or this product does not stay down when lowered, then you'll need to decrease

Lift Strength:

Adjustment may take up to: 72 full 360° revolutions

WARNING

STORED ENERGY HAZARD!

DO NOT OPEN TOWER OR REMOVE

SAFETY GUARD!

A primary mechanism within the tower is under tension and can be hazardous to people exposed to it under certain extreme conditions. DO NOT open the tower; DO NOT attempt to service the cart/stand. DO NOT remove safety guards or labels designed to protect or inform of possible hazards. Only

Ergotron-approved installers may service or otherwise modify cart/stand. Failure to heed this

Warning may result in serious

Personal Injury and Damage both to the cart/stand and equipment.

822-959-00

9 of 11

888-33-332-W-02 rev.G • 03/15

B

Adjustment may take up to: 115 full 360° revolutions

C

4mm

Increase Lift Strength

If the mounted weight is too heavy or this product does not stay up when raised, then you'll need to increase

Lift Strength:

Decrease Lift Strength

If the mounted weight is too light or this product does not stay down when lowered, then you'll need to decrease

Lift Strength:

a

11

4x

M5 x 8mm

How to attach optional CPU holder ordered separately b

10 of 11

888-33-332-W-02 rev.G • 03/15

Set Your Workstation to Work For YOU!

Learn more about ergonomic computer use at: www.computingcomfort.org

Height Position top of screen slightly below eye level.

Position keyboard at about elbow height with wrists fl at.

Distance Position screen an arm's length from face—at least 20” (508mm).

Position keyboard close enough to create a 90˚ angle in elbow.

Angle Tilt screen to eliminate glare.

Tilt the keyboard back 10° so that your wrists remain fl at.

To Reduce Fatigue

Breathe - Breathe deeply through your nose.

Blink - Blink often to avoid dry eyes.

Break • 2 to 3 minutes every 20 minutes

• 15 to 20 minutes every 2 hours.

For local customer care phone numbers visit: http://contact.ergotron.com

888-33-332-W-02 rev.G • 03/15

© 2015 Ergotron, Inc.

11 of 11