www.sacelectronics.co.uk

AE0596

SAC 60m HDMI over Single Cat5/5e/6/7

U S E R M A N U A L

INTRODUCTION

Thank you for purchasing this Extender. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual safe for future reference.

The AE0596 Extender uses a Single cat 5/5E/6/7 cable up to 60 meters instead of using a

HDMI cable to transmit high definition signal, cutting down cost. Long distance transmission of high definition is very difficult because a HDMI cable is very expensive and infrequent. The

Extender is designed to supply long distance transmission of a high definition signal.

Our devices offer solutions for sound, space, security, data center control, information distribution, conference room presentation, school and corporate training environments.

FEATURES

 Support video input : 24/50/60fps/1080p/1080i/720p/576p/576i/480p/480i

 Signal transmission: use one cat5/5e/6 or 7(recommend cat6 or 7) to connect the sender and receiver, the Ethernet cable can be up to 60m long.

 Supports 3D

 Support video output : 24/50/60fps/1080p/1080i/720p/576p/576i/480p/480i

 Audio format support : DTS-HD/Dolby-trueHD/LPCM7.1/DTS/Dolby-AC3/DSD

 LED indication: when power is supplied or device is working, LED indicator is on.

 Supports up to 60 meters AWG26 cable length between extender and source & sink device

 No loss of quality

 Installs in minutes

 Powered by DC5V/1A power supply (included)

Accessories

1、2 x 5V Power Adapter

2、1 x User manual

Power Adaptor

Physical Connection Picture：

Figure 1.0 Front Panel Picture

Cat: Use one cat to connect the sender and the receiver.

Switcher: This button needs to be pressed if digital display cannot read EDID info

Steps to use the Switcher button:

1. Connect the power adaptor with the power port on the HDMI extender

2. Connect the HDMI output on the HDMI extender with the HDMI input port of the display.

3. Make sure you select the correct input channel on device.

4. Press the Switcher button on the HDMI extender and wait for device to read EDIF info, once finished status LED light should go green.

5. Take the HDMI cable out and power off with the HDMI extender; it can be used in normal mode.

Note: Extender can used with HDMI-DVI cable for DVI Monitor. The step is same as above.

Figure 1.1 Rear and side picture

HDMI IN: Signal Source Input.

HDMI OUT: To connect receiver to HDTV or other display.

DC 5V: 5V DC-DC Power Adaptor Interface.

Operating and Connecting：

1. Connect one HDMI cable up to 15 meters between source device and TX Extender

2. Connect one HDMI cable up to 15 meters between sink device and RX Extender

3. Connect one cat5e/6/7(recommended cat6 or 7) to the sender and receiver, the cable can be up to 60m in length

4. Connect the power adaptors to the sender and receiver.

SPECIFICATIONS: AE0596

Length of CAT cable between Rx and TX

…..……………….…………………….Up to 60 meters

HDMI I nput…..………………….........……24/50/60fps/1080p/1080i/720p/576p/576i/480p/480i

Support audio format input..

………..…DTS-HD/Dolby-trueHD/LPCM7.1/DTS/Dolby-AC3/DSD

HDMI Output…..…………….…...…………24/50/60fps/1080p/1080i/720p/576p/576i/480p/480i

Support audio format output...

……. ……………………..………LPCM7.1/DTS/Dolby-AC3/DSD

Max bandwidth……………………………………………………..…….……………………225MHz

Max ban d rate……………….…….………………….……………...………………………6.75Gbps

Input Video signal

………….…………………………..…………..…………….… 0.5~1.5Volts p-p

Output DDC signal ………………………………………………………………… 5Volts p-p (TT1L)

Input/Output HDMI cable distance………….………………...≤15m AWG26 HDMI standard cable

HDCP Compliant

……………………………………………………………………………………Yes

Max working current……………………………………………………..……….…………...600mA

Power adapter format………..…Input: AC (50HZ, 60HZ) 100V-240V; Output: DC5V/1A(RX/TX)

Operating Temperature range……..…………….……………………….…………… (-15 to +55℃)

Operating Humidity range………………………….……..……….5 to 90%RH (No Condensation)

Dimension (L x W x H)

……………………………….…………………82x44x22 (mm) (RX/TX)

Weight…..………………………………………………………..……………………..…………195g

Notes:

Please only use the machine in accordance with instructions to ensure the machine has a long life span.

1. The machine should always be placed in a position away from damp, hot, dusty and erosive environments.

2. All parts should be free from strong vibrations, impacts, and the possibility of falling.

3. Never touch power adaptors while your hands are wet.

4. Please hold the power adaptor connector when disconnecting the power adapter.

5. Please turn the power off when the machine is n’t being used for long periods of time.

6. Please do not open the cover and do not touch the inside parts.

7. Please ONLY use the original factory power adaptor.

Before you power on, please check the connection line carefully and make sure that all interfaces are normally connected. See common troubleshooting below:

Serial NO

Trouble

Description

Cause and Ways to deal with

1、Check if the power adaptor connector is truly and

1

2

3

No Power correctly inserted in to the power socket.

2、Check if the power switch is on.

1、Please make sure that the TV or device is on and

No Picture has been connected properly to the machine.

2 、 Check if the signal source is on and properly connected.

3、Check the system connection quality.

4、Check if the line is all good quality.

5、Check the cable quality

1、Unplug everything and try again

Obscure Picture

2、Check HDMI cable quality