QUBINO ZMNHCD1 manual

output shouldn’t be active more than 120s. Beyond

enable add/remove mode on main controller,
Group 2: multilevel sensor report (triggered at change of
stop the movement.
this time overheating protection can be activated (in

press service button S for more than 6 second or
temperature sensor) up to 16 nodes.
Keeping pressed push-button (>2s) connected to I1 (up),
this case outputs will switch off for 60s).

press push button I1 five times within 3s (5 times
Automatic calibration
initiates up movement, until push-button is released.
Package contents
change switch state within 3 seconds) in the first 60
Automatic calibration is a process during which the Flush
Keeping pressed push-button (>2s) connected to I2

seconds after the module is connected to the power
shutter DC learns the position of the limit switches.
(down), initiates down movement, until push-button is
supply.
Shutter positioning calibration
released.
By this function all parameters of the module are set to
(par. 71 set to 0)
Manual operation for venetian blinds
default values and own ID is deleted.
There are two procedures of calibration.
(par. 71 set to 1)
If service button S is pressed more than 2 and less than 6
Calibration through main controller UI
Slates on start position - 0 degree
second module is excluded, but configuration parameters
1)
Include the module into the Z-wave network,
Clicking push-button (for time < full turn slates time-par.72)
according to module include instructions.
connected to I1 (up), initiates slates turning towards end -
Set the parameter 78 (Forced Flush shutter DC
180 degree position, until push-button is released.
calibration) value to 1.
Clicking push-button (for time < full turn slates time-par.72)
Flush shutter DC performs the calibration process,
connected to I2 (down), initiates shutter down movement.
completing full cycle - up, down and up again.
If the shutter is moving, each click, of any push-button, will
Set the parameter 78 (Forced Flush shutter DC
stop the movement.
calibration) value to 0.
Keeping pressed push-button (for time > full turn slates
Qubino
Flush shutter DC
Electrical diagram 12 - 24VDC
The INNOVATIVE and SMALLEST
Flush shutter DC
are not set to default values.
Associations
ORDERING CODE
Z-WAVE FREQUENCY
ZMNHOD1
2)
Association enables Flush shutter DC module to transfer
commands inside Z-wave network directly (without main
868,4 MHz
3)
controller) to other Z-Wave modules.
ZMNHOD2
921,4 MHz
ZMNHOD3
908,4 MHz
ZMNHOD4
869,0 MHz
Associated Groups:
4)
Root device:
Notes for the diagram:
Group 1: default reporting group (reserved for the main
Calibration through the inputs I1 and I2
time-par.72) connected to I1 (up), initiates full slates turn
controller).
1)
and up movement, until the push-button is released.
Group 2: basic on/off (triggered at change of the input I1
according to module inclusion instructions.
Keeping pressed push-button (for time > full turn slates
state and reflecting its state) up to 16 nodes.
2)
time-par.72) connected to I2 (down), initiates shutter down
Group 3: basic on/off (triggered at change of the input I2
input and wait until the shutter reach upper limit switch.
movement, until the push-button is released.
state and reflecting its state) up to 16 nodes.
3)
Keeping pressed push-button (for time > (full turn slates
Group 4: basic on/off (triggered at sensing moving
input and wait until the shutter reach lower limit switch.
time +2s)) connected to I1 (up), initiates up movement,
direction of roller: up=FF, down=0) up to 16 nodes.
4)
until push-button is released.
Include the module into the wireless network,
+
+VDC (12 – 24VDC)
This Z-Wave module is used to control the motor of blinds,
-
-VDC (0V)
rollers, shades, venetian blinds, etc.. The module can be
Q1
Output for motor UP (open)
controlled either through a Z-Wave network or through the
Q2
Output for motor DOWN (close)
wall switch.
I2
Input for switch/push button DOWN (close)
Precise positioning is supported for motors equipped with
I1
Input for switch/push button UP (open)
mechanical or electronic end switches. The module is
TS
Terminal for digital temperature sensor (only
Group 5: basic on/off (triggered at reaching roller position:
input and wait until the shutter reach upper limit switch.
Slates on end position - 180 degree
designed to be mounted inside a “flush mounting box”,
for Flush shutter DC module compatible digital
bottom=FF, top=0) up to 16 nodes.
Slates tilting position calibration
Clicking push-button (for time < full turn slates time-par.72)
hidden behind a traditional wall switch. Module measures
temperature sensor, which must be ordered
Group 6: basic on/off (triggered at reaching roller position:
(par. 71 set to 1)
connected to I1 (up), initiates shutter up movement.
power consumption of motor and support connection of
separately).
bottom=FF, not bottom=0) up to 16 nodes.
When enabling venetian blind mode, position calibration
Clicking push-button (for time < full turn slates time-par.72)
Group 7: multilevel set (triggered at changes of value of
for slats titling must be done. After doing this, position and
connected to I2 (down), initiates slates turning towards
Service button (used to
the Flush shutter DC position) up to 16 nodes.
angle of slates can be set. By default full turn time for
start - 0 degree position, until the push-button is released.
add or remove module
Group 8: multilevel set (triggered at changes of value of
slates is set to 1,5s. This value can be changed with
If the shutter is moving, each click, of any push-button, will
from
slats tilting position) up to 16 nodes.
parameter 72.
stop the movement.
Group 9: multilevel sensor report (triggered at change of
1)
Include and make module calibration according to
Keeping pressed push-button (for time > full turn slates
section ‘Shutter positioning calibration’.
time-par.72) connected to I1 (up), initiates shutter up
ZMNHOD5
916,0 MHz
digital temperature sensor. It is designed to act as repeater
in order to improve range and stability of Z-wave network.
S
Supported switches
Module supports mono-stable switches (push button)
and bi-stable switches.
the
Z-Wave
network).
Installation
temperature sensor) up to 16 nodes.

Before the installation disconnect power supply.
Module Inclusion (Adding to Z-wave network)

Connect the module according to electrical diagram.


Locate the antenna far from metal elements (as far

as possible).

Do not shorten the antenna.
Quick press the switch/push-button connected to I1
Quick press the switch/push-button connected to I2
Quick press the switch/push-button connected to I1
End point 1:
2)
Set parameter 71 to 1 ‘Venetian blinds’.
movement, until the push-button is released.
Connect module to power supply (with
Group 1: Lifeline group, 0 nodes allowed.
3)
Exclude the module (without reset!).
Keeping pressed push-button (for time > full turn slates
temperature sensor connected - if purchased),
Group 2: basic on/off (triggered at change of the input I1
4)
Include the module.
time-par.72) connected to I2 (down), initiates full slates
auto-inclusion (works for about 5 seconds after
state and reflecting its state) up to 16 nodes.
5)
After module inclusion beside main shutter widget,
turn and down movement, until the push-button is
connected to power supply) or
Group 3: basic on/off (triggered at change of the input I2
another widget for slates control will appear on UI.
released.
By default full turn movement is set to 1,5s. If this time
Keeping pressed push-button (for time > (full turn slates
Danger of electrocution!

press service button S for more than 2 second or


state and reflecting its state) up to 16 nodes.
press push button I1 three times within 3s (3 times
Group 4: basic on/off (triggered at sensing moving
is too long (if after slates full cycle shutter starts
time +2s)) connected to I2 (down), initiates down
change switch state within 3 seconds).
direction of roller: up=FF, down=0) up to 16 nodes.
moving up or down), decrease this time defined with
movement, until push-button is released.
Module installation requires a great degree of skill and
may be performed only by a qualified and licensed
6)
electrician.
NOTE1: For auto-inclusion procedure, first set main
Group 5: basic on/off (triggered at reaching roller position:
parameter 72. If this time is to short (if slats will not
Configuration parameters
Even when the module is turned off, voltage may be
controller into inclusion mode and then connect module to
bottom=FF, top=0) up to 16 nodes.
turn for full cycle), increase this time defined with
Parameter no. 10 - Activate/deactivate functions ALL
present on its terminals. Any works on configuration
power supply.
Group 6: basic on/off (triggered at reaching roller position:
parameter 72.
ON / ALL OFF
changes related to connection mode or load must be
NOTE2: When connecting temperature sensor to module
bottom=FF, not bottom=0) up to 16 nodes.
Manual operation for shutter
Available config. parameters (data type is 2 Byte DEC):
always performed by disconnected power supply
that has already been included, you have to exclude
Group 7: multilevel set (triggered at changes of value of
(par. 71 set to 0)

default value 255
(disable the fuse).
module first. Switch off power supply, connect the sensor
the Flush shutter DC position) up to 16 nodes.
Module allows connecting of push-buttons (mono-stable)

255 - ALL ON active, ALL OFF active.
Note!
and re-include the module.
End point 2:
or switches (bi-stable) to I1 and I2 terminals.

0 - ALL ON is not active, ALL OFF is not active

Group 1: Lifeline group, 0 nodes allowed.
Clicking push-button (<2s) connected to I1 (up), initiates

1 - ALL ON is not active ALL OFF active
recommended values. Connect the module only in
Module Exclusion/Reset
Z-Wave network)
up movement.

2 - ALL ON active ALL OFF is not active
accordance to the

Group 2: multilevel set (triggered at changes of value of
Connect module to power supply

slats tilting position) up to 16 nodes.
Clicking push-button (<2s) connected to I2 (down),
Module responds to commands ALL ON / ALL OFF that
bring module within maximum 1 meter (3 feet) of the
End point 3:
initiates down movement.
may be sent by the main controller or by other controller
main controller,
Group 1: Lifeline group, 0 nodes allowed.
If the shutter is moving, each click, of any push-button, will
belonging to the system.

Do not connect the module to loads exceeding
below diagrams.
Improper
connections may be dangerous.

When device is loaded with max. rated current 2A,
(Removing
from
This parameter defines shutter motor moving time of
configuration parameters (data type is 1 Byte DEC):
Parameter no. 40 - Power reporting in Watts on power
complete opening or complete closing.

default value 8 = 800ms
change for Q1 or Q2
configuration parameters (data type is 2 Byte DEC):

3 – 50 = 0,3seconds – 5seconds (100ms resolution)
Set value means percentage, set value from 0 – 100 = 0%

default value 0
Parameter no. 86 – Power consumption at limit switch
Dimensions (WxHxD)
41,8x36,8x15,4mm
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
COMMAND_CLASS_VERSION_V2
COMMAND_CLASS_SENSOR_MULTILEVEL_V7
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V2
- 100%. Available configuration parameters (data type is 1

0 – moving time disabled (working with limit
delay time
(package)
(79x52x22)
NOTE: The above list is valid for the product with a
switches)
This parameter defines the max time at limit switch, when
Weight (Brutto with package)
28g (34g)
temperature sensor connected to TS terminal at the time
1 – 32767 = 0,1seconds – 3276,7seconds. After that
power consumption is below power threshold. If the power
For installation in boxes
Ø ≥ 60mm or 2M
of inclusion. In case the sensor is not connected then the
time motor is stopped (relay goes to off state)
consumption during this time is below power threshold
Switching
H bridge
following command class and endpoint 3 are not
Byte DEC):

Available
default value 1

0 – reporting disabled

1 – 100 = 1% - 100% Reporting enabled. Power
NOTE: Important is that the reference position to manually
(par. 76), the active output will switch off, means that limit
report is send (push) only when actual power (in
set moving time is always shutter lower position!
switch is reached. Available configuration parameters
Watts) in real time changes for more than set
Set parameter 74 to 0 and move the shutter (using
(data type is 1 Byte DEC):
percentage comparing to previous actual power in
up/down push buttons or main controller UI) to the lowest

default value 8 = 800ms
Watts, step is 1%.
desired position. On this shutter position, set parameter 74

3 – 50 = 0,3seconds – 5seconds (100ms resolution)
NOTE: if power changed is less than 1W, the report is not
to time for complete opening or complete closing. At this
Parameter no. 90 – Time delay for next motor
send (pushed), independent of percentage set.
point shutter can be moved up (open) for set time, but
movement
Parameter no. 42 – Power reporting in Watts by time
can't be moved down because this position is already set
This parameter defines the minimum time delay between
interval for Q1 or Q2
as lower shutter position.
next motor movement (minimum time between switching
Set value means time interval (0 – 32767) in seconds,
To change shutter lower position below already set
motor
when power report is send. Available configuration
(manual recalibration), parameter 74 must be set to 0 and
parameters (data type is 1 Byte DEC):
parameters (data type is 2 Byte DEC):
repeat the procedure described above.

default value 5 = 500ms

default value 300 = 300s
In case shutter has limit switches, but anyhow you would

1 – 30 = 0,1seconds – 3seconds (100ms resolution)

0 – Reporting Disabled
like to limit opening/closing position by time, you can still
Parameter no. 110 – Temperature sensor offset

1 – 32767 = 1 second – 32767 seconds. Reporting
do it. In case you put time that is longer that
settings
enabled, power report is send with time interval set
opening/closing real time limited by limit switches, shutter
Set value is added or subtracted to actual measured value
by entered value.
will stop at limit switch, but the module relay will switch off
by sensor.
Parameter no. 71 – Operating modes
after define time, not by shutter limit switch. Take in
is 2 Byte DEC):
This parameter defines selection between two available
consideration that in this condition, the positioning with

default value 32536
operating modes. Available configuration parameters
slider through UI will not show correct shutter position.

32536 – offset is 0.0C
(data type is 1 Byte DEC):
Parameter no. 76 - Motor operation detection

From 1 to 100 – value from 0.1 °C to 10.0 °C is

default value 0
Power threshold to be interpreted when motor reach the

0 – Shutter mode
limit switch. Available configuration parameters (data type

1 – Venetian mode (up/down and slate rotation)
is 1 Byte DEC):
and
on
again).
Available
configuration
Available configuration parameters (data type
From 1001 to 1100 – value from -0.1 °C to -10.0 °C is
subtracted to actual measured temperature.
NOTE: When setting parameter, module needs to be

default value 6 = 0,6W
Parameter no. 120 – Digital temperature sensor
excluded and included again! Please check detailed

Available settings: 5 - 100 (0,5W - 10W), step is
reporting
0,1W.
If digital temperature sensor is connected, module reports
description in this manual.
Parameter no. 72 – Slats tilting full turn time
NOTE: Motors with power consumption less than 0,5W
measured temperature on temperature change defined by
This parameter defines the time necessary for slats to
could not be auto calibrated. In that case set time
this parameter. Available configuration parameters (data
make full turn (180 degrees). Available configuration
manually (par. 74).
type is 1 Byte DEC):
parameters (data type is 2 Byte DEC):
Parameter no. 78 - Forced Shutter DC calibration

Default value 5 = 0,5°C

default value 150 = 1,5 seconds
By modifying the parameters setting from 0 to 1 a Shutter

0 – Reporting disabled

0 – Tilting time disabled
DC module enters the calibration mode. Available

1-127 = 0,1°C – 12,7°C, step is 0,1°C

1 – 32767 = 0,01seconds – 327,67 seconds
configuration parameters (data type is 1 Byte DEC):
NOTE: If time set is too high, this will result that after full

default value 0
turn, shutter will start move up/down, for time remaining.

1 - Start calibration process (when calibration
Power supply
12-24VDC +/-10%
Parameter no. 73 – Slats position
process is finished, completing full cycle - up, down
Rated load current
2A
This parameter defines slats position after up/down
and up, set the parameter 78 (Forced Shutter
Overcorrect protection
5A
movement through Z-wave or push-buttons. Available
calibration) value back to 0.
Output circuit power of DC
48W (24VDC)
Technical Specifications
configuration parameters (data type is 1 Byte DEC):
Parameter no. 85 – Power consumption max delay
output (resistive load)

default value 1
time
Power measurement

0 - Slats return to previously set position only in case
This parameter defines the max time before motor power
accuracy
of Z-wave control (not valid for limit switch positions).
consumption is read after one of the relays is switched
Digital temperature sensor
1 - Slats return to previously set position in case of
ON. If there is no power consumption during this max
range (sensor must be
Z-wave control, push-button operation or when the
time (motor not connected, damaged or requires higher
ordered separately)
lower limit switch is reached.
time to start, motor in end position,...) the relay will switch

Parameter no. 74 – Motor moving up/down time
OFF. Time is defined by entering it manually. Available
materials)
supported:
Z-Wave Device Class:
BASIC_TYPE_ROUTING_SLAVE
GENERIC_TYPE_SWITCH_MULTILEVEL
SPECIFIC_TYPE_CLASS_C_MOTOR_CONTROL
Z-Wave Supported Command Classes:
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
COMMAND_CLASS_VERSION_V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1
COMMAND_CLASS_POWERLEVEL_V1
COMMAND_CLASS_BASIC_V1
COMMAND_CLASS_SWITCH_ALL_V1
COMMAND_CLASS_SWITCH_BINARY_V1
COMMAND_CLASS_SWITCH_MULTILEVEL_V3
COMMAND_CLASS_METER_V4
COMMAND_CLASS_SENSOR_MULTILEVEL_V7
COMMAND_CLASS_MULTI_CHANNEL_V4
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V2
COMMAND_CLASS_CONFIGURATION_V1
COMMAND_CLASS_MARK
COMMAND_CLASS_BASIC_V1
COMMAND_CLASS_SWITCH_MULTILEVEL_V3
Endpoint1:
Device Class:
added to actual measured temperature.

up to 30 m indoors
(depending on building

off
Distance
+/-5%
-50 ~ +125°C
COMMAND_CLASS_SENSOR_MULTILEVEL_V7
Endpoint 2 is supported by the module only when the
parameter no. 71 is set to the value 1 and the module is
excluded and re-included into the network.
This product can be included and operated in any Z-Wave
network with other Z-Wave certified devices from any
other manufacturers. All constantly powered nodes in the
same network will act as repeaters regardless of the
vendor in order to increase reliability of the network.
Important disclaimer
Z-wave wireless communication is inherently not always
100% reliable, and as such, this product should not be
used in situations in which life and/or valuables are solely
dependent on its function.
Warning!
Do not dispose of electrical appliances as unsorted
municipal waste, use separate collection facilities.
Contact your local government for information regarding
BASIC_TYPE_ROUTING_SLAVE
GENERIC_TYPE_SWITCH_MULTILEVEL
SPECIFIC_TYPE_CLASS_C_MOTOR_CONTROL
the collection systems available. If electrical appliances
Command Classes:
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
substances can leak into the groundwater and get into the
COMMAND_CLASS_VERSION_V2
COMMAND_CLASS_BASIC_V1
COMMAND_CLASS_SWITCH_ALL_V1
COMMAND_CLASS_SWITCH_BINARY_V1
COMMAND_CLASS_SWITCH_MULTILEVEL_V3
COMMAND_CLASS_METER_V4
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V2
COMMAND_CLASS_MARK
COMMAND_CLASS_BASIC_V1
COMMAND_CLASS_SWITCH_MULTILEVEL_V3
Endpoint2:
Device Class:
are disposed of in landfills or dumps, hazardous
food chain, damaging your health and well-being. When
replacing old appliances with new once, the retailer is
legally obligated to take back your old appliance for
disposal at least for free of charge.
This user manual is subject to change and improvement
without notice.
NOTE: User manual is valid for module with SW version
S3 (SW version is part of P/N)!
Example: P/N: ZMNHODx H1S3P1
BASIC_TYPE_ROUTING_SLAVE
GENERIC_TYPE_SWITCH_MULTILEVEL
SPECIFIC_TYPE_CLASS_C_MOTOR_CONTROL
Qubino
Command Classes:
Goap d.o.o. Nova Gorica
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
COMMAND_CLASS_VERSION_V2
COMMAND_CLASS_BASIC_V1
COMMAND_CLASS_SWITCH_ALL
COMMAND_CLASS_SWITCH_BINARY_V1
COMMAND_CLASS_SWITCH_MULTILEVEL_V3
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V2
COMMAND_CLASS_MARK
COMMAND_CLASS_BASIC_V1
COMMAND_CLASS_SWITCH_MULTILEVEL_V3
Ulica Klementa Juga 007
Endpoint 3:
Device Class:
Operation temperature
-10 ~ +40°C
GENERIC_TYPE_SENSOR_MULTILEVEL
SPECIFIC_TYPE_ROUTING_SENSOR_MULTILEVEL
Electricity consumption
cca. 0,3W
Command Classes:
5250 Solkan
Slovenia
E-mail: [email protected]
Tel:
+386 5 335 95 00
Web:
www.qubino.com
Date: 15.10.2015
Document: Qubino_Flush shutter DC
PLUS user manual_V1.2_eng