- No category
advertisement
Satellite Receiver
User’s Guide
Changing Entertainment. Again.
Important Information
WARNING
To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
CAUTION
RISK OF ELECTRIC
SHOCK. DO NOT OPEN.
Caution: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel.
This symbol indicates
"dangerous voltage" inside the product that presents a risk of electric shock or personal injury.
This symbol indicates important instructions accompanying the product.
Cautions
Note to Cable TV Installer:
Note to Satellite Dish Installer:
IMPORTANT NOTICE:
Care and Cleaning:
Do not stack electronic components or other objects on top of the
Digital Satellite Receiver. The slots on top of the receiver must be left
uncovered to allow proper airflow to the unit. Blocking the airflow to the unit could impair performance or damage your receiver and other components.
Remove any sales or promotional materials attached to the product.
Do not stack the digital satellite receiver on top of a “hot component” such as an audio power amplifier.
FCC Regulations state that unauthorized changes or modifications to this equipment may void the user’s authority to operate it.
This reminder is provided to call your attention to article 820-40 of the
National Electrical Code (Section 54 of the Canadian Electrical Code, Part 1 which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.
This reminder is provided to call your attention to articles 810 and 820 of the
1999 National Electrical Code. Refer to article 810, in particular to 810-1 and
810-15, for required grounding of the metal structure of the Dish Antenna.
Refer also to the 810-2 which, by reference to article 820, requires that the satellite dish coaxial cable shield be connected to the grounding system of the building as close to the point of cable entry as practical.
This device incorporates an anticopy process technology that is protected by
U.S. patents and other intellectual property rights. The anticopy process is licensed for non-commercial, home use only. Reverse engineering or disassembly is prohibited.
Use a soft cloth or dusting attachment of your vacuum cleaner to dust your digital satellite receiver. Remove dust from the ventilation holes on the top and bottom.
Plastic surfaces are easily scratched and can be marred by alcohol and various solvents. Avoid excessive use of oil-based furniture polishes since the materials used in the cabinet will accumulate more dust. A non-abrasive, anti-static cleaner/polisher is recommended.
Product Registration
Please fill out the product registration card (packed separately) and return it immediately. Returning the card allows us to contact you if needed.
Product Information
Keep your sales receipt to obtain warranty parts and service and for proof of purchase. Attach it here and record the serial and model numbers in case you need them. These numbers are located on the product.
Model No. __________________________________________________________________________________________
Serial No. __________________________________________________________________________________________
Purchase Date: ______________________________________________________________________________________
Dealer/Address/Phone: ______________________________________________________________________________
Introduction
Key Features Overview
Your digital satellite receiver is equipped with features that will add to your viewing experience.
The following information summarizes a few of these features. Chapter 3 provides more information about the rest of the TV’s features and how to use them.
On-screen Program Guides
Description: Available on-screen guides include a new Advanced Program
Guide™ which stores up to seven days of programming information and a new
Advanced Program Guide ® which lists five different channels of programming at a glance.
Requirements: Complete the on-screen assisted setup. You’ll find detailed
instructions how to do this in Chapter 1, Connections & Setup.
VCR1 ON • OFF TV
DVD VCR2 AUX SAT
MUTE
CH +
SKIP
FETCH
GUIDE
CH -
OK
GO BACK
INFO
(-)
1
MENU
2 3
CLEAR
4 5 6
7 8
WHO•INPUT
0
9
ANTENNA
REVERSE PLAY FORWARD
RECORD STOP PAUSE
Interactive Channel Banner
Description: A transparent banner at the top of the picture allows direct access
to the key features of the digital satellite receiver including a way to display the
Main Menu, viewing suggestions, program details, The Guardian™ channel locking system, on-screen message display, the Scout™ keyword/phrase and the AlphaSort™ alphabetical search features, and alternate audio offerings.
Requirements: Press the INFO button on the remote control. Highlight
different icons using the remote control’s arrow buttons. Select the highlighted icon using the remote control’s OK button.
Dolby Digital Sound Capability
Description: Dolby Digital
®
(when available) provides six independent soundtrack channels through the optical and coaxial output jacks. When connected to an optional, compatible six-channel amplifier/receiver and speakers, these connections provide Dolby Digital
®
Surround Sound.
Requirements: A TV with digital audio input jacks, or a digital audio receiver/
decoder.
Universal Remote Control
Description: Provides complete satellite system operation, and primary
function control of most brands of remote-controllable TVs, VCRs, and cable boxes.
Requirements: A remote-controllable device such as a VCR, cable box, etc.
The remote control may have to be programmed to operate your component if it is not RCA, GE, or Proscan.
1
2
Introduction
VCR
One-button Record
Description: Records any program being watched with the touch of one
button. The receiver sends infrared commands to the VCR to execute the recordings at the proper time.
Requirements: Connect the satellite receiver to the VCR and attach the infrared
cable on top of the VCR’s remote control sensor. Set up the digital satellite receiver system using the first-time assisted setup and follow the directions on page 19 to select the VCR type.
DIRECTV INTERACTIVE™ powered by WINK
Communications
®
Description: An interactive television service that lets you access up-to-the-
minute news, sports, financial information, weather, program trivia, and respond to free offers and even shop– all while you watch TV.
Requirements: Establish a free, secure Interactive TV account, then press the
OK/i button on the remote control whenever you see the Interactive logo ( ) appear on-screen. For more information, see page 32 in the Satellite System
Features chapter.
Software Upgrades via Satellite
Description: The digital satellite receiver is able to modify some of its features
and functions with downloaded RSA-secure upgrades or modifications. RSAsecure downloads ensure that only authorized upgrades are delivered to your
RCA digital satellite receiver.
Requirements: Consult the Upgrade Menu to find a schedule of upgrades or
modifications planned by DIRECTV. For more information, see page 62 in the
Using On-screen Menus chapter.
Table of Contents
Connections & Setup ................................................................................................ 5
Advanced Audio (Digital Audio Output Connection) ............................................ 14
Using the Remote Control .................................................................................... 21
Using the Satellite System’s Features ............................................................. 29
The DIRECTV INTERACTIVE™ Feature .............................................................. 32
Customizing Viewing Suggestions .............................................................. 36
3
4
Table of Contents
Using the Menu System ......................................................................................... 39
Displaying Program Guides ............................................................................... 42
Schedule a Timer with the RECORD Button ..................................................... 49
Other Information ................................................................................................... 65
Chapter 1
Connections & Setup
Chapter Overview:
• Things to Consider Before You Connect
• Choose Your Connection
• Place Batteries in the Remote Control
• Assisted Setup
• Order Programming
Changing Entertainment. Again.
Graphics contained within this publication are for representation only
5
6
Connections & Setup
Things To Consider Before You Connect
Components
Protect Your Components from Power Surges
• Connect all components before plugging any power cords into the wall outlet.
• Always turn off the digital satellite receiver, TV and other components before you connect or disconnect any cables.
Position Cables Correctly to Avoid Audio Hum or
Interference
• Insert all cable plugs firmly into their jacks.
• Place the Audio/Video (A/V) cables to the sides of the TV’s back panel instead of straight down the middle after you connect your components.
• Try not to coil any twin-lead cables and keep them away from the A/V cables as much as possible.
• Make sure all antennas and cables are properly grounded. Refer to the Safety Tips sheet packed with your unit.
Protect Your Components from Overheating
• Do not block ventilation holes in any of the components. Arrange the components so that air can circulate freely. Remove any sales or promotional materials attached to the
product.
• Do not stack components.
• Allow adequate ventilation when placing components in a stand.
• Place an amplifier or receiver on the top shelf of the stand so heated air rising from it will not flow around other components.
Chapter 1
Connections & Setup
Choose Your Connection
There are several ways to connect your digital satellite receiver depending on the components you want to connect and the quality of the signal you want to achieve. Please use the following chart to determine which connection is best for you. Proceed to the appropriate page and connect your satellite receiver. For more information about the relationship between cables, jacks, and the quality of the signal, go to pages 15-16.
Component Signal Quality Jacks on the satellite receiver
Excellent
Very Good
Basic
TV
S-VIDEO, AUDIO L and R
VIDEO, AUDIO L and R
OUT TO TV
Very Good VIDEO, AUDIO L and R
Good OUT TO TV
VCR
Cables needed*
S-video, audio/video audio/video coaxial audio/video coaxial
Go to...
page 8 page 10 page 12 page 8 page 10 optical (SPDIF) page 18 Excellent
Receiver
* Pictures of cables are on page 15.
DIGITAL AUDIO
Chapter 1 7
Connections & Setup
Digital Satellite Receiver
GROUND
SATELLITE
IN
LOW SPEED
DATA
OUT TO TV
IN FROM ANT
VCR
S-VIDEO
VIDEO
R
L
AUDIO
DIGITAL
AUDIO
PHONE
JACK
5
Satellite Dish
Antenna
1
VCR
CH3
CH4
2
IN
FROM
ANT
OUT
TO
TV
4
Cable or
Off-air
Antenna
6
7
TV
3
IN
FROM
ANT
R
AUDIO
L
VIDEO
S-Video
Note: Your VCR and TV back panels may not look exactly like the ones illustrated.
RJ11 modular phone jack
8
Excellent Connection
Using S-Video and A/V jacks and cables to connect to the TV,
RF coaxial cables to connect the VCR
This connection provides the best picture quality, surpassing that of A/V cables. The S-Video cable, which carries video information only, requires that audio cables also be used for sound.
Chapter 1
Connections & Setup
What you will need:
• Two (2) RF coaxial cables
• Two (2) A/V cables
• One (1) S-Video cable
• One (1) telephone line cord
• Coaxial cable lines fed from a digital satellite antenna and a standard TV antenna (or cable line)
Making the Connection
1. Connect the satellite dish antenna feed (RG-6 coaxial cable) to the SATELLITE IN jack on the satellite receiver.
2. Connect one end of an RF coaxial cable to the OUT TO TV jack on the satellite receiver, and the other end to the antenna input jack on the VCR.
Note: If your VCR has A/V input jacks, you can use A/V cables to connect the satellite receiver’s second
A/V jacks to the A/V jacks of the VCR instead of using the RF coaxial cable.
3. Connect one end of an RF coaxial cable to the antenna output jack on the VCR, and the other end to the
TV’s antenna input jack.
4. Connect the cable or off-air antenna feed (RF coaxial cable) to the IN FROM ANT jack on the satellite receiver.
5. Connect one end of the supplied telephone line cord to the PHONE JACK on the back of the satellite receiver, and the other end to an RJ11-type modular phone jack (the most common type of phone jack).
6. Connect two ends of the supplied A/V cables to AUDIO R and L jacks on the satellite receiver, and the other ends to the corresponding audio input jacks on the TV.
Note: Make sure you connect jacks by their labels. For example, AUDIO R on the digital satellite receiver should be connected to TV’s right audio input jack, L Audio to L Audio, etc.
If your TV only has one audio input jack, use the satellite receiver’s AUDIO L jack to make the connection.
7. Connect one end of the supplied S-Video cable to the satellite receiver, and the other end to the
S-Video input jack on the TV.
Go to Page 15
Using Your Components
To watch DIRECTV
®
programming:
Tune the TV to its S-Video line input (if you have difficulty finding your TV’s S-Video line input, see your
TV’s User’s Manual or page 66 in this manual). Then tune the satellite receiver to the desired channel.
To record DIRECTV
®
programming:
Tune the satellite receiver to the desired channel. Then set your VCR to record on the proper input channel (video line input if using A/V cables to connect the VCR to the satellite receiver, channel 3 or 4 if using RF coaxial cable).
To view VCR recordings:
Tune the TV to channel 3 or 4 (whichever is set on the VCR as its output channel). Begin VCR playback as usual.
Chapter 1 9
Connections & Setup
Digital Satellite Receiver
GROUND
SATELLITE
IN
LOW SPEED
DATA
OUT TO TV
IN FROM ANT
VCR
S-VIDEO
VIDEO
R
L
AUDIO
DIGITAL
AUDIO
PHONE
JACK
5
Satellite Dish
Antenna
1
VCR
CH3
CH4
2
IN
FROM
ANT
OUT
TO
TV
4
Cable or
Off-air
Antenna
6
3
TV
IN
FROM
ANT
R
AUDIO
L
VIDEO
Note: Your VCR and TV back panels may not look exactly like the ones shown.
RJ11 modular phone jack
Very Good Connection
Using A/V jacks and cables to connect to the TV,
RF coaxial cables to connect the VCR
This connection provides better picture quality than RF coaxial cables and is recommended for use with TVs that do not have S-Video input jacks.
10 Chapter 1
Connections & Setup
What you will need:
• Two (2) RF coaxial cables
• Three (3) Audio/Video cables
• One (1) telephone line cord
• Coaxial cable lines fed from a digital satellite antenna and a standard TV antenna (or cable line)
Making the Connection
1. Connect the satellite dish antenna feed (RG-6 coaxial cable) to the SATELLITE IN jack on the satellite receiver.
2. Connect one end of an RF coaxial cable to the OUT TO TV jack on the satellite receiver, and the other end to the antenna input jack on the VCR.
Note: If your VCR has A/V input jacks, you can use A/V cables to connect the satellite receiver’s second set of A/V output jacks to the A/V jacks of the VCR instead of using the RF coaxial cable.
3. Connect one end of an RF coaxial cable to the antenna output jack on the VCR, and the other end to the TV’s antenna input jack.
4. Connect the cable or off-air antenna feed (RF coaxial cable) to the IN FROM ANT jack on the satellite receiver.
5. Connect one end of the supplied telephone line cord to the PHONE JACK on the back of the satellite receiver, and the other end to an RJ11-type modular phone jack (the most common type of phone jack).
6. Connect the ends of the supplied A/V cables to the satellite receiver’s AUDIO and VIDEO jacks, and the other ends to the corresponding AUDIO and VIDEO input jacks on the TV.
Notes: Make sure you connect jacks and cables corresponding to their labels. For example, AUDIO R output on the digital satellite receiver should be connected to AUDIO R input on the TV, VIDEO OUT to
VIDEO IN, etc.
If your TV only has one audio input jack, use the satellite receiver’s AUDIO L jack to make the connection.
Go to Page 15
Using Your Components
To watch DIRECTV
®
programming:
Tune the TV to its video line input (if you have difficulty finding your TV’s video line input, see your
TV’s User’s Manual or refer to the instructions on page 66 in this manual). Then tune the satellite receiver to the desired channel.
To record DIRECTV
®
programming:
Follow the steps in the previous step, then tune the satellite receiver to the desired channel. Set your
VCR to record on its proper input channel (channel 3 or 4).
To view VCR recordings:
Tune the TV to channel 3 or 4 (whichever is set on the VCR as its output channel). Begin VCR playback as usual.
Chapter 1 11
Connections & Setup
Digital Satellite Receiver
GROUND
SATELLITE
IN
LOW SPEED
DATA
OUT TO TV
IN FROM ANT
VCR
S-VIDEO
VIDEO
R
L
AUDIO
DIGITAL
AUDIO
PHONE
JACK
5
Satellite Dish
Antenna
1
VCR
CH3
CH4
2
IN
FROM
ANT
OUT
TO
TV
4
Cable or
Off-air
Antenna
RJ11 modular phone jack
TV
3
IN
FROM
ANT
Note: Your VCR and TV back panels may not look exactly like the ones shown.
Basic Connection
Using RF Coaxial cables for all connections
This connection provides standard picture quality. This connection is only recommended for use with TVs that do not have S-Video or A/V input jacks.
12 Chapter 1
Connections & Setup
What you will need:
• Two (2) RF coaxial cables
• One (1) telephone line cord
• Coaxial cable lines fed from a digital satellite antenna and a standard TV antenna (or cable line)
Making the Connection
1. Connect the satellite dish antenna feed (RG-6 coaxial cable) to the SATELLITE IN jack on the satellite receiver.
2. Connect one end of an RF coaxial cable to the OUT TO TV jack on the satellite receiver, and the other end to the antenna INPUT jack on the VCR.
3. Connect one end of an RF coaxial cable to the antenna OUTPUT jack on the VCR, and the other end to the TV’s antenna INPUT jack.
4. Connect the cable box or off-air antenna feed (RF coaxial cable) to the IN FROM ANT jack on the satellite receiver.
5. Connect one end of the supplied telephone line cord to the PHONE JACK on the back of the satellite receiver, and the other end to an RJ11-type modular phone jack (the most common type of phone jack).
Go to Page 15
Using Your Components
To watch DIRECTV
®
programming:
Tune the TV to the satellite receiver’s output channel (either channel 3 or 4).
Note: You can change the satellite receiver’s output channel by pressing the remote control’s SAT button, then the MENU button, then select System Setup, then System Options, and finally select
Output Channel. Use the remote control’s arrow and OK buttons to highlight and select the desired output channel. Tune the TV to that channel to see the satellite receiver’s picture.
To record DIRECTV
®
programming:
Follow the directions in the previous step, then set your VCR to record on its proper input channel
(channel 3 or 4 if using RF coaxial cable to make the connection, Video Line Input if using A/V cables to connect the VCR to the satellite receiver).
To view VCR recordings:
Tune the TV to channel 3 or 4 (whichever is set on the VCR as its output channel). Begin VCR playback as usual.
Chapter 1 13
Connections & Setup
Receiver or Decoder with Optical Input
DIGITAL
AUDIO
INPUT
Digital Satellite Receiver
GROUND
SATELLITE
IN
LOW SPEED
DATA
OUT TO TV
IN FROM ANT
VCR
S-VIDEO
VIDEO
R
L
AUDIO
DIGITAL
AUDIO
PHONE
JACK
Advanced Audio
(Digital Audio Output Connection)
Cables: Optical (SPDIF)
Use this connection to take advantage of Dolby Digital † quality sound, when available.
Notes: Your digital receiver back panel may not look exactly like the one pictured.
This satellite receiver’s optical digital output jack fully complies with the international standard governing this type of jack (IEC958), and is designed for connection to a Dolby Digital (AC-3 or
PCM) receiver or Dolby Digital (AC-3 or PCM) decoder. Older equipment, some of which is not fully compliant with IEC958, may not be compatible with the Dolby Digital bitstream. Such a connection using anything other than a PCM, Dolby Digital, or Dolby Pro Logic receiver or decoder could create a high noise level, causing damage to headphones or speakers.
Making the Connection
Connect one end of the optical (SPDIF) cable to the DIGITAL AUDIO OUTPUT jack* on the satellite receiver, and to the digital audio input jack on a Dolby Digital receiver/decoder.
Using Your Component
After you connect your satellite receiver to a Dolby Digital receiver, you must select Dolby Digital from the System Options menu (press the remote control’s MENU button, then select System Setup, then System Options, then highlight Dolby Digital. Use the remote control’s arrow and OK buttons to highlight and select Autoselect, PCM, or Dolby Digital in order for the receiver to recognize the digital audio connection.
For more information on this feature, see the Dolby Digital entry starting on page 59 in the section, Using The Menu System.
* Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby
Laboratories. Confidential Unpublished Works. ©1992-1997 Dolby Laboratories, Inc. All rights reserved.
14 Chapter 1
Connections & Setup
Jacks and Cables
Below is a description of the jacks and cables you can use to make connections. Not all cables come with your digital satellite receiver.
S-VIDEO
VIDEO
L
AUDIO
R
ANTENNA IN
VCR
S-Video Jack and Cable
S-Video jacks/cables provide this receiver’s best picture quality. Remember to connect the left and right audio cables to the TV because the S-Video cable carries only the picture signal, not the sound.
Audio/Video (A/V) Jack and Cable (RCA-type)
Audio/Video (A/V) cables provide good picture quality and stereo sound, and should be used if your TV has no S-video jacks. The digital satellite receiver’s A/V jacks are color coded (yellow for video, red for right audio, and white for left audio). If your TV has only one input for audio (mono), connect it to the left
(white) audio jack on the satellite receiver.
RF Jack and Coaxial Cable (F-type)
RF jacks provide good picture and mono sound quality. They should be used if
A/V connections are not available on your TV. RF jacks are used for off-air antenna and cable feed connections. The RF jacks on the receiver are labeled
IN FROM ANT and OUT TO TV. The coaxial cable supplied with your system is used to connect the receiver to your TV/VCR’s antenna input jack.
VCR Controller
The VCR Controller plugs into the VCR jack on the satellite receiver’s back panel. Attach the other end of the cable to your VCR’s remote control sensor.
DIGITAL
AUDIO
PHONE
Digital Audio Output (SPDIF)
If you own a Dolby Digital receiver that uses an optical cable-type input, use an optical (SPDIF) cable to connect the satellite receiver to your Dolby Digital receiver or decoder for the best sound quality.
Telephone Jack and Cord
The telephone line cord is required to connect your satellite receiver to a telephone line if you choose to subscribe to *DIRECTV ® programming. The phone line connection is used to periodically call out to DIRECTV. You will need an RJ11-type modulator jack (the most common type of phone jack) which might look like one of those pictured here. If you don’t have a modular jack, call your local telephone company to find out how to get one installed.
DIRECTV programming is subject to the terms and conditions of the DIRECTV Customer Agreement; a copy is provided at DIRECTV.com and with your first bill.
DIRECTV, the Cyclone Design logo, and Advanced Program Guide are trademarks of DIRECTV, Inc., a unit of Hughes Electronics Corp., and are used with permission.
Chapter 1 15
Connections & Setup
SATELLITE
IN
LOW SPEED
DATA
OUT TO TV IN FROM ANT
VCR
S-VIDEO
VIDEO AUDIO
DIGITAL
AUDIO
PHONE
JACK
Satellite Receiver Rear Panel
This diagram illustrates each of the back panel jacks found on your digital satellite receiver. When working with cables, be sure to connect corresponding OUTPUTS and INPUTS (Video OUT to
Video IN, Right Audio OUT to Right Audio IN, etc.).
For more information on the function of the back panel jacks and many other features of your digital satellite receiver, press the MENU button and select System Setup from the Main menu, then select System Index.
Back Panel Jacks (in alphabetical order)
AUDIO (R and L)
Audio cables offer better sound quality than RF coaxial cables. Connect a second set of audio cables to another component, such as a VCR or stereo.
DIGITAL AUDIO
Connects the satellite receiver’s audio to a Dolby Digital receiver or decoder.
This audio connection provides the best sound quality. Use the optical DIGITAL AUDIO output cable (SPDIF) for this receiver’s best possible sound.
IN FROM ANT
Connect a standard TV antenna or cable feed to the satellite receiver using this jack. You can then switch between the satellite receiver’s signal and the TV/cable feed using the remote control’s ANTENNA button to toggle between the two.
LOW SPEED DATA
This port allows you to connect your digital satellite receiver to future services and accessories as they become available. A shielded cable and additional hardware may be required.
OUT TO TV
Connects the satellite receiver to your TV or VCR using RF coaxial cable. This jack provides the most basic connection, carrying average sound and video quality.
PHONE JACK
Connects the satellite receiver to a telephone line. The digital satellite receiver requires a telephone line connection to periodically communicate with your program provider.
SATELLITE IN
Use to connect the satellite receiver to the satellite dish antenna.
S-VIDEO
Provides better picture quality than VIDEO or RF coaxial cable jacks. If your TV has an S-Video jack, use it along with the audio jacks (S-Video only carries picture information, not sound) to connect to your TV.
VCR
This jack allows the satellite receiver to control the VCR using an IR cable. The cable is attached above the VCR’s remote control sensor. This connection is required for One-Touch
Record and Timer recording features.
VIDEO
Provides better picture quality than the OUT TO TV jack. Connect the second VIDEO jack to another device, such as a VCR. You must also connect the AUDIO cables when using the
VIDEO connection.
16 Chapter 1
Chapter 1
Connections & Setup
Place Batteries in the Remote
Control
Follow these steps whenever you need to install or change the batteries in your digital satellite receiver’s remote control.
Note: When replacing old batteries, you may need to reprogram the remote control to operate other devices.
1. Remove the cover from the battery compartment.
2. Insert batteries in the battery compartment, matching the + and – end of each battery.
3. Replace the cover.
Plug in and Turn On the Receiver
Plug the end of the power cord into the wall outlet. Be sure to insert the plug completely.
To turn on the satellite receiver, press the SAT button on the remote control or the ON•OFF button on the front panel. If your TV brand is RCA, GE, or
Proscan, press the TV button on the remote control to turn on the TV. If your
TV brand is not RCA, GE, or Proscan, see page 25 in the next section, Using the
Remote Control, for details on programming the satellite receiver’s remote control to operate your TV.
Locating the VCR’s Infrared
Remote Control Sensor
The VCR Controller must be affixed directly over the infrared remote control sensor on your VCR.
Some VCRs have a label that identifies the remote control sensor, but others do not. If the IR sensor is labeled on your VCR, affix the VCR Controller directly over the sensor. For VCRs that do not label the sensor, you can use the VCR’s remote control to locate the VCR’s sensor before affixing the VCR Controller cable.
To Find the VCR’s Remote Control Sensor:
1. Hold the VCR’s remote control so that it is touching the front of the VCR.
2. Slowly move the remote control over the front of the VCR while repeatedly pressing the remote control’s power button.
3. When your VCR turns on/off, you have located the remote control sensor.
Note: To test the VCR controller’s position, use a piece of vinyl tape to temporarily attach the VCR controller to the spot where you think the sensor is located. Then see Selecting a VCR Type on page 19 to see if the VCR
Controller is positioned correctly.
17
Connections & Setup
Satellite Receiver (Back Panel)
VCR
SATELLITE
IN
LOW SPEED
DATA
OUT TO TV
IN FROM ANT
S-VIDEO
VIDEO
R
L
AUDIO
DIGITAL
AUDIO
PHONE
JACK
VCR (Front Panel)
Remonte Control
IR Sensor
Connect the VCR Controller
To use the One-Touch Record and Timer features, you need to attach the VCR Controller cable to the VCR and the satellite receiver.
1. Plug the VCR Controller into the VCR jack on the satellite receiver.
2. Affix the other end in front of the remote control sensor on your VCR.
Arrow buttons
MENU button
VCR1
ON • OFF
TV
DVD VCR2 AUX SAT
MUTE
CH +
SKIP
FETCH
GUIDE
CH -
GO BACK
INFO
OK
(-)
1
MENU
2 3
CLEAR
4 5 6
7 8
WHO•INPUT
0
REVERSE PLAY
9
ANTENNA
FORWARD
RECORD STOP PAUSE
OK button
CLEAR button
Using Highlight and Select
All on-screen menus can be handled the same way, using highlight and select navigation.
Highlight and select navigation has two steps:
1. Use the arrow buttons (up, down, left, and right) on the remote control to highlight different choices on the screen.
2. Press OK to select the highlighted item.
Note: When a highlighted on-screen menu choice has a number beside it, you can also press the corresponding number button on the remote control to select it.
Once you know how to navigate on-screen menus, you can complete the
Assisted Setup (see the next page) and explore the menu system.
To display the on-screen menu system, press the remote control’s SAT button, then press the MENU button.
Note: Don’t worry about getting stuck inside a menu. Pressing the
CLEAR button on the remote control takes you out of the menu system and back to the program you were watching.
18 Chapter 1
Chapter 1
Connections & Setup
Selecting a VCR Type
In order to use the One-Touch Record and Timer features, you need to tell the satellite receiver which VCR brand you are using.
1. Tune the TV to its satellite receiver viewing channel (either 03, 04, or the
TV’s appropriate input channel depending on your connections).
2. Press MENU on the remote control to display the satellite receiver’s Main menu.
2. Highlight and select number 7, System Setup.
3. Highlight and select number 3, System Options.
4. Highlight and select number 2, Set VCR Type.
5. Highlight and select the name of your VCR manufacturer.
Note: If you do not see your VCR manufacturer’s name, select Other (at the bottom of the list) and enter the appropriate code from the VCR Remote
Control code list on page 27.
6. Follow the on-screen instructions to ensure that you are using the correct code (if you need more assistance while in a menu, press the remote control’s INFO button for details).
Note: Some VCR brands may not be capable of being controlled by the receiver.
Complete the Assisted Setup
If you installed your satellite dish antenna yourself, you may have already used the Assisted Setup to find dish-pointing coordinates, acquire and fine-tune the signal, and run a system test.
If you need to run the setup again, select System Setup from the Main menu, then select Assisted Setup.
To check your dish-pointing coordinates or run the signal strength meter, display the Main menu, then select System Setup, and finally Dish Pointing.
19
Connections & Setup
Tip
When you order programming, you need to know your access card number.
To get the number, select System Setup from the Main menu, then System Test.
Wait for the system to run all of its tests. The access card number is displayed at the end of the system test.
Write the access card number in the space below for easy reference:
Order Programming
After you have installed your DIRECTV System, you should contact DIRECTV to order DIRECTV
®
programming.
With this receiver and the proper satellite dish antenna, you may be able to subscribe to local channels from DIRECTV in certain areas. Additional equipment may be required in some markets. Check with your retailer or visit
DIRECTV.com for information on availability of local channels from DIRECTV in your area.
Activation of programming may be subject to credit approval and requires valid service address, social security number and/or major credit card. Programming subject to change. You must be physically located in the U.S. to receive DIRECTV service. DIRECTV services not available outside the U.S. DIRECTV ® programming is sold separately and independently of DIRECTV System hardware. A valid programming subscription is required to operate DIRECTV System hardware.
Activate your DIRECTV
®
programming today at 1-800-DIRECTV (1-800-347-3288).
20 Chapter 1
Using the
Remote Control
Chapter Overview:
• Remote Control Buttons
• Buttons on Top of the Digital Satellite Receiver
• Programming the Remote Control
• Using the Remote Control to Operate
Another Component
• Modes of Operation
• Controlling a Second Satellite Receiver
• Remote Control Codes
Chapter 2
Changing Entertainment. Again.
Graphics contained within this publication are for representation only
21
Using the Remote Control
LED
VCR1 ON • OFF TV
DVD VCR2 AUX SAT
MUTE
CH +
SKIP
V
FETCH
GUIDE
CH -
GO BACK
INFO
OK
(-)
1
MENU
2 3
6
CLEAR
4 5
7 8
WHO•INPUT
0
REVERSE PLAY
9
ANTENNA
FORWARD
RECORD STOP PAUSE
Remote Control Buttons
in Alphabetical Order
ANTENNA
In TV mode, lets you toggle between the satellite and standard TV/ cable signals when the satellite receiver is connected to the TV using the OUT
TO TV jack. In VCR mode, ANTENNA functions as a TV/VCR input button.
Arrows
Use the navigation arrows to move the on-screen highlight up, down, left, or right.
AUX
Turns on a compatible RCA amplifier/receiver or audio/video receiver.
This button can be programmed to control an RCA, GE, or Proscan auxiliary component.
CH + (up) /- (down)
Use to scan up and down through the channels in the current channel list. If you are in the program guide or menu system, use the
CH +/- buttons to page up and down a screen at a time.
CLEAR
Removes the on-screen displays and returns you to normal viewing.
Digit Buttons (0 - 9)
Used to tune directly to a specific channel. If you are in the menu system, use the digits to select menu items. In the menu system, use 0 to return to the previous menu screen.
DVD
Tells the remote to operate the DVD player. Note that this button is only functional with RCA, GE, and Proscan DVD players.
FETCH
Displays the Fetch menu with up to eight different actions, or executes a single task- depending on the preferences set.
GO BACK
Moves you back and forth between the last two selected channels. In the menu system, returns you to the previous screen.
GUIDE
Brings up the program guide. Subsequent presses of the GUIDE button switch between the Detail and Grid guide formats.
INFO
Brings up the on-screen channel banner, password challenge, or purchase offer screen. In the program guides, press to get information about the highlighted program or channel. In the menu system, this button displays context-sensitive help for highlighted control elements.
LED (Light-Emitting Diode)
This light is illuminated with each valid button press. When programming the remote control, it flashes or turns on or off to indicate programming status.
MENU
Displays the Main menu. When you are using the remote control to operate an RCA, GE, or Proscan VCR (the remote is in VCR mode), the MENU button functions as a Program button.
MUTE
When the remote is programmed to control a TV, this button reduces the TV’s volume to its minimum level. Press again to restore the volume.
22 Chapter 2
Using the Remote Control
OK/i (interactive)
Selects a highlighted choice if you are in the menu system.
Press the OK button when the DIRECTV INTERACTIVE ™ icon ( ) appears during interactive programs and commercials. Pressing OK will display more information and offer the chance to interact with what is displayed on screen.
ON•OFF
Turns the component you are controlling on or off. When pressed twice within two seconds, all components that are on will be turned off (this feature only works with most RCA,
GE, and Proscan products). You can also use the ON•OFF button on the top (front panel) of the digital satellite receiver to turn the receiver on or off.
SAT
Tells the remote to control the digital satellite receiver.
SKIP
Used to activate the commercial skip mode on RCA. GE, and Proscan products that offer
Commercial Skip feature. Commercial Skip activates an on-screen timer. This feature allows you to change channels (during a commercial break, for example), then be returned to the original channel that was active when skip was first pressed when the timer reaches zero. Each press of the SKIP button increases the timer by 30 seconds.
Transport Buttons (REVERSE, PLAY, FORWARD, RECORD, STOP, PAUSE)
When in onscreen guides, PLAY advances the display two hours, FORWARD advances the display 12 hours and REVERSE moves time backward 12 hours. When the remote control is programmed, these buttons are also used to control an auxiliary component, such as a VCR or laserdisc player. Note that if your VCR Controller is connected, the RECORD button can be used to schedule a timer recording when using the Program Guide or to begin recording while watching a program (in VCR mode).
TV
When programmed, tells the remote to control the TV.
VCR1
When programmed, tells the remote to control the VCR.
VCR2
When programmed, tells the remote to control a second VCR.
VOL down and up
When programmed, adjusts the audio volume of your TV.
WHO•INPUT
Press the WHO button one or more times to scroll through the user profiles.
When you are using the remote control to operate an RCA, GE, or PROSCAN TV (in TV mode), press the WHO•INPUT button one or more times to scroll through the available video input sources.
Chapter 2 23
Using the Remote Control
Top of the Digital Satellite Receiver
This diagram illustrates the buttons on the top (also referred to as the front panel) of the digital satellite receiver. For more information on the function of the front panel buttons and many other features of your digital satellite receiver, press the MENU button and select System Setup from the
Main menu, then select System Index.
CHANNEL
ON •
OFF
MENU
OK
INFO
Front Panel Buttons (Left to Right)
ON•OFF
Use to turn your digital satellite receiver on for viewing or off when you are not viewing it. Your receiver will still be able to download software upgrades and receive messages from program providers when it is off.
MENU•OK
Use this button to display the Main menu. If you are already in the menu system, pressing this button selects the highlighted item.
Arrows
Use the navigation arrows to move the on-screen highlight up, down, left, or right.
Channel Down and Up
When you’re watching TV, use these buttons to change the channel.
INFO
Use this button to display the channel banner, password challenge, or purchase offer screen. Press twice to display additional program information, when available. While in the menu system INFO also summons context sensitive help about a highlighted menu item.
24 Chapter 2
Component buttons and
ON•OFF button
PLAY button
REVERSE button
LED
VCR1
ON • OFF
TV
DVD VCR2 AUX SAT
MUTE
CH +
SKIP
V
FETCH
GUIDE
CH -
GO BACK
INFO
OK (-)
1
4
MENU
2
5
3
6
CLEAR
7 8
WHO•INPUT
0
REVERSE PLAY
9
ANTENNA
FORWARD
RECORD STOP PAUSE
STOP button
Using the Remote Control
Programming the Remote Control
The digital satellite receiver’s remote can be programmed to control most brands of remote controllable components. The remote is already programmed to control most RCA, GE and Proscan components; it may need to be programmed to control other manufacturers’ brands.
Testing the Remote Control
To determine whether the universal remote control needs to be programmed, turn a component on, such as a VCR, point the remote at the VCR, and press the VCR button. Then press ON•OFF or CH + or CH - to see if the VCR responds to the remote commands. If not, the remote needs to be programmed.
There are two ways to program the remote control: Automatic Code Search or
Direct Entry.
Using Automatic Code Search
The following instructions can be used to program the remote to control many of the components connected to your TV. If you want to exit the automatic code search without programming any of your components, press the CLEAR button until the LED (red light) turns off.
1. Turn on the component you want to control (VCR, satellite receiver, etc.)
2. Press and hold the button you want to program. While holding the component button, press and hold ON•OFF until the LED on the remote control turns on, then release both buttons.
Note: The AUX button can only be programmed using direct code entry. See
“Using Direct Entry,” later in this section, for details.
3. Point the remote at the component, press and release PLAY, then wait five seconds or until the LED stops flashing.
At this point the remote control is searching for the correct code to program.
If, after five seconds, the component you want to control does not turn off, press and release PLAY again to tell the remote to search the next set of codes.
Continue pressing and releasing PLAY until the component turns off or you have searched through all of the codes. There are 20 total sets of codes. If the component does not turn off after pressing PLAY 20 times, then the remote cannot control that particular component.
If the component you want to control does turn off:
1. Press and release REVERSE, then wait two seconds. Repeat this step until the component turns back on.
2. To finish, press and hold STOP until the LED on the remote control turns off.
Chapter 2 25
Using the Remote Control
Using Direct Entry
1. Turn on the component to be programmed.
2. Look up the brand and code number(s) for the component on the code list at the end of this section.
3. On your remote control, press and hold the component button you want to program.
4. While pressing the component button, enter a code from the code list.
5. Release the component button, and then press ON•OFF to see if the component responds to the remote control commands. If it doesn’t, try pressing the component button and then
ON•OFF again.
6. If you get no response, repeat these steps using the next code listed for your brand, until the component responds to the remote control commands.
One Button Recording
If your remote is programmed to operate a VCR, and the VCR is properly connected to the satellite receiver, you only need to press the RECORD button to begin recording from video.
Operating Other Components
Once the remote has been programmed successfully, you are ready to use it to operate your components.
To Operate the Component:
1. Press the component button (TV, VCR1, SAT, VCR2, or AUX) to set the remote to control the component.
2. Press ON•OFF to turn the component on or off.
3. Use the remote control buttons that apply to that component.
Modes of Operation
Because this universal remote can control several different components (DVD player, VCR, cable box, etc.) it uses operational modes triggered by the component buttons. For example, if you want the remote control to operate the
TV, press the TV button to put the remote into TV mode. If you want to play a videotape, press VCR1 then PLAY (pointing the remote at the VCR).
Controlling a Second Satellite Receiver
The remote can control two satellite receivers. From the Main menu, select
System Setup, then System Options, then Remote Setup. Then follow the onscreen instructions and enter the appropriate code from the Satellite Receiver list at the end of this section. By default, the SAT button is used to control the first satellite receiver and the AUX button is used to control the second satellite receiver.
If your second receiver is an RCA, GE, or Proscan and you want to control it using the AUX button, use code 5001. Code 5000 is used by the SAT button.
26 Chapter 2
Using the Remote Control
Remote Control Codes
TV
Abex ............................................................................ 1172
Admiral .................................................... 1001, 1173, 1211
Adventura .................................................................... 1174
Aiko ............................................................................. 1016
Akai .............................................................................. 1002
Alleron ......................................................................... 1046
Amtron ......................................................................... 1038
Anam National .................... 1003, 1038, 1192, 1193, 1194
AOC ................. 1004, 1005, 1006, 1007, 1175, 1176, 1195
Audiovox ..................................................................... 1038
Belcor .......................................................................... 1004
Bell & Howell ......................................... 1001, 1083, 1162
Bradford ...................................................................... 1038
Brokwood ................................................................... 1004
Candle ........................................... 1004, 1006, 1008, 1174
Celebrity ...................................................................... 1002
Centurion ..................................................................... 1009
Citizen ....................... 1004, 1006, 1008, 1016, 1038, 1105,
1171, 1174, 1177
Colortyme ................................................ 1004, 1006, 1010
Concerto ............................................................ 1004, 1006
Contec/Cony ................................. 1012, 1013, 1014, 1038
Craig ............................................................................ 1038
Crown ................................................................ 1038, 1171
Curtis Mathes ...................... 1000, 1004, 1006, 1015, 1105,
1162, 1171, 1212
CXC .............................................................................. 1038
Daewoo .................... 1004, 1005, 1006, 1016, 1017, 1018,
1127, 1171, 1196
Daytron .................................................... 1004, 1006, 1171
Dimensia ..................................................................... 1000
Dumont ............................................................. 1004, 1151
Dynatech ..................................................................... 1178
Electroband ................................................................. 1002
Electrohome .............. 1003, 1004, 1006, 1019, 1020, 1022
Emerson .................... 1004, 1006, 1012, 1023, 1024, 1025,
1026, 1027, 1028, 1029, 1030, 1031, 1032,
1033, 1034, 1035, 1036, 1037, 1038, 1039,
1041, 1042, 1043, 1044, 1046, 1047, 1123,
1124, 1162, 1171, 1177, 1179, 1191, 1208
Envision ............................................................. 1004, 1006
Fisher ................................... 1048, 1049, 1051, 1162, 1180
Fujitso .......................................................................... 1046
Funai .................................................................. 1038, 1046
Futuretec ...................................................................... 1038
GE ......... 1000, 1003, 1004, 1006, 1022, 1052, 1054, 1055,
1087, 1164, 1165, 1166, 1167, 1168, 1181, 1213
Gibralter ............................................................ 1004, 1151
Goldstar .................... 1004, 1005, 1006, 1012, 1019, 1056,
1057, 1058, 1155, 1156, 1171, 1172
Grundy .................................................... 1038, 1046, 1171
Hallmark ............................................................ 1004, 1006
Harvard ........................................................................ 1038
Hitachi ............ 1004, 1006, 1012, 1013, 1014, 1059, 1060,
1061, 1135, 1136, 1137, 1138, 1139, 1140,
1141, 1142, 1143, 1144, 1145, 1146, 1148,
1150, 1179, 1198, 1199
IMA .............................................................................. 1038
Infinity ......................................................................... 1062
JCPenney ........ 1000, 1004, 1005, 1006, 1008, 1022, 1052,
1054, 1058, 1063, 1064, 1072, 1087, 1105,
1128, 1171, 1172, 1181, 1201
Janeil ............................................................................ 1174
JBL ............................................................................... 1062
JCB ............................................................................... 1002
Jensen ................................................................ 1004, 1006
JVC .................. 1012, 1013, 1014, 1054, 1060, 1065, 1066,
1067, 1157, 1158, 1159, 1182
Kawasho .................................................. 1002, 1004, 1006
Kaypani ....................................................................... 1175
Kenwood ................................................. 1004, 1006, 1019
Kloss Novabeam ........................... 1068, 1069, 1174, 1183
KTV ................................................ 1038, 1070, 1171, 1177
Loewe .......................................................................... 1062
Logik ............................................................................ 1083
Luxman .............................................................. 1004, 1006
LXI .................. 1000, 1006, 1049, 1062, 1071, 1072, 1073,
1162, 1181, 1207
Magnavox ................. 1004, 1006, 1008, 1019, 1062, 1068,
1069, 1075, 1076, 1077, 1088, 1130,
1131, 1132, 1133, 1134, 1183, 1219, 1235
Majestic ........................................................................ 1083
Marants ........................................................................ 1062
Marantz .......................................... 1004, 1006, 1062, 1078
Megatron ........................................................... 1006, 1059
MEI .............................................................................. 1176
Memorex ............................. 1001, 1006, 1082, 1083, 1162
MGA ................ 1004, 1005, 1006, 1019, 1022, 1051, 1079,
1080, 1082
Midland ................................ 1054, 1151, 1171, 1172, 1181
Minutz .......................................................................... 1052
Mitsubishi ................. 1004, 1005, 1006, 1019, 1022, 1051,
1079, 1080, 1081, 1082, 1125
Montgomery Ward ...................................................... 1083
Motorola ............................................................ 1003, 1173
MTC ............................................... 1004, 1005, 1006, 1105
Multitech ...................................................................... 1038
Multivision ................................................................... 1084
NAD ............................................... 1006, 1071, 1072, 1185
NEC ...................................... 1003, 1004, 1005, 1006, 1200
Nikko ................................................................. 1006, 1016
NTC .............................................................................. 1016
Onwa ........................................................................... 1038
Optimus ....................................................................... 1185
Optonica ............................................................ 1095, 1173
Orion ................................................................. 1035, 1191
Panasonic ............................ 1003, 1054, 1062, 1170, 1214
Philco .... 1003, 1004, 1005, 1006, 1008, 1012, 1019, 1062,
1068, 1069, 1075, 1077, 1183
Philips ............. 1003, 1004, 1008, 1012, 1019, 1062, 1068,
1069, 1075, 1076, 1086, 1087, 1088, 1089
Pilot .................................................................... 1004, 1171
Pioneer ............ 1004, 1006, 1090, 1091, 1092, 1179, 1185
Portland ............................... 1004, 1005, 1006, 1016, 1171
Price Club .................................................................... 1105
Prism ............................................................................ 1054
Proscan .............................................................. 1000, 1181
Proton ............................................ 1004, 1006, 1012, 1093
Pulsar ................................................................. 1004, 1151
Quasar ........................................... 1003, 1054, 1070, 1094
Radio Shack/Realistic ......... 1000, 1004, 1006, 1012, 1038,
1049, 1095, 1162, 1171, 1172
RCA ....... 1000, 1003, 1004, 1005, 1006, 1007, 1019, 1096,
1098, 1099, 1100, 1101, 1102, 1103, 1129, 1179,
1181, 1187, 1188, 1190, 1202, 1203, 1215, 1233
Runco .......................................................................... 1151
Sampo ............................................ 1004, 1006, 1171, 1172
Samsung ................... 1004, 1005, 1006, 1012, 1015, 1019,
1104, 1105, 1106, 1171, 1172, 1204
Samsux ........................................................................ 1171
Sansui .......................................................................... 1191
Sanyo ........................ 1004, 1048, 1049, 1080, 1107, 1108,
1162, 1169, 1180
Scotch .......................................................................... 1006
Scott ................. 1004, 1006, 1012, 1024, 1035, 1038, 1046
Sears ............... 1000, 1004, 1006, 1013, 1014, 1019, 1046,
1048, 1049, 1051, 1066, 1071, 1072, 1109,
1110, 1162, 1180, 1181, 1189
Sharp ......................... 1004, 1006, 1012, 1029, 1095, 1111,
1112, 1113, 1122, 1171, 1173
Shogun ........................................................................ 1004
Signature .................................................. 1001, 1083, 1115
Simpson ....................................................................... 1008
Sony ............................................... 1002, 1205, 1216, 1218
Soundesign .......................... 1004, 1006, 1008, 1038, 1046
Squareview .................................................................. 1189
SSS ..................................................................... 1004, 1038
Starlite .......................................................................... 1038
Supre-Macy .................................................................. 1174
Supreme ...................................................................... 1002
Sylvania .......... 1004, 1006, 1008, 1019, 1062, 1068, 1069,
1075, 1076, 1077, 1088, 1116, 1161, 1183
Symphonic ............................................... 1033, 1038, 1189
Tandy ........................................................................... 1173
Tatung .......................................................................... 1003
Technics ....................................................................... 1054
Techwood ................................................ 1004, 1006, 1054
Teknika ..................... 1004, 1005, 1006, 1008, 1012, 1013,
1014, 1016, 1038, 1046, 1076, 1082,
1083, 1105, 1170, 1171
Telecaption .................................................................. 1117
TMK ................................................................... 1004, 1006
Toshiba ..................... 1049, 1071, 1072, 1089, 1105, 1109,
1117, 1118, 1160, 1162
Totevision .................................................................... 1171
Universal ............................................................ 1052, 1087
Victor ................................................................. 1066, 1182
Vidtech .................................................... 1004, 1005, 1006
Viking .......................................................................... 1174
Wards .............. 1000, 1001, 1004, 1005, 1006, 1019, 1024,
1033, 1046, 1052, 1062, 1068, 1069, 1075,
1076, 1083, 1087, 1088, 1095, 1119, 1120
Yamaha .......................................... 1004, 1005, 1006, 1019
Zenith ....................... 1004, 1083, 1151, 1152, 1153, 1154,
1210, 1217
VCR
Admiral ........................................................................ 2132
Zaiko ............................................................................ 2027
Aiwa ............................................................................. 2026
Akai .......... 2003, 2004, 2005, 2007, 2008, 2111,2112, 2113
American High ............................................................ 2021
Asha ............................................................................. 2013
Audio Dynamics ................................................ 2009, 2010
Audiovox ..................................................................... 2014
Bell & Howell ............................................................. 2011
Beaumark .................................................................... 2013
Broksonic .......................................................... 2012, 2025
Calix ............................................................................. 2014
Candle ............. 2013, 2014, 2015, 2016, 2017, 2018, 2019
Canon ...................................................... 2021, 2022, 2114
Capehart ............................................................ 2020, 2110
Carver .......................................................................... 2062
CCE .................................................................... 2027, 2061
Citizen ...... 2013, 2014, 2015, 2016, 2017, 2018,2019,2027
Colortyme .................................................................... 2009
Colt .............................................................................. 2061
Craig .............................................. 2013, 2014, 2023, 2061
Curtis-Mathes ...................... 2000, 2009, 2013, 2016, 2018,
2021, 2022, 2024, 2115, 2131
Cybernex ..................................................................... 2013
Daewoo ... 2015, 2017, 2019,2025, 2026, 2027, 2028, 2110
Daytron ........................................................................ 2110
DBX ................................................................... 2009, 2010
Dimensia ........................................................... 2000, 2131
Dynatech ..................................................................... 2026
Electrohome ...................................................... 2014, 2029
Electrophonic .............................................................. 2014
Emerson .......... 2012, 2014, 2015, 2021, 2024, 2025, 2026,
2029, 2030, 2031, 2032, 2033, 2034, 2035,
2036, 2037, 2038, 2039, 2040, 2041, 2042, 2044,
2045, 2046, 2047, 2065, 2113, 2116, 2117, 2130
Fisher ....... 2011, 2023, 2048, 2049, 2050, 2051, 2052,2118
Fuji ..................................................................... 2021, 2119
Funai ............................................................................ 2026
Garrard ........................................................................ 2026
GE ............................. 2000, 2001, 2013, 2021, 2022, 2053,
2115, 2120, 2131
Goldstar ......................................... 2009, 2014, 2018, 2054
Gradiente ..................................................................... 2026
Harley Davidson ......................................................... 2026
Harman Kardon .......................................................... 2009
Harwood ..................................................................... 2061
Headquarter ................................................................ 2011
Chapter 2 27
Code List
Remote Control Codes (Cont.)
VCR (Cont’)
Hitachi ............. 2055, 2056, 2057, 2107, 2111, 2120, 2122
HI-Q ............................................................................. 2023
Instant Replay ............................................................. 2021
JCL ............................................................................... 2021
JC Penney ....... 2009, 2010, 2011, 2013, 2014, 2021, 2022,
2055, 2056, 2058, 2059, 2060, 2107, 2118
Jensen ...................................................... 2055, 2056, 2111
JVC ............................. 2009, 2010, 2011, 2018, 2111, 2123
Kenwood .................. 2009, 2010, 2011, 2016, 2018, 2058,
2111, 2123
KLH .............................................................................. 2061
Kodak ................................................................ 2014, 2021
Lloyd ............................................................................ 2026
Logik ............................................................................ 2061
LXI ............................................................................... 2014
Magnavox ................. 2021, 2022, 2062, 2063, 2104, 2105,
2108, 2124
Magnin ......................................................................... 2013
Marantz .. 2009, 2010, 2011, 2016, 2018, 2021, 2062, 2064
Marta ............................................................................ 2014
Masushita ..................................................................... 2021
MEI .............................................................................. 2021
Memorex ......... 2011, 2013, 2014, 2021, 2023, 2026, 2132
MGA ......................................................... 2029, 2065, 2113
MGN Technology ........................................................ 2013
Midland ........................................................................ 2053
Minolta ..................................................... 2055, 2056, 2107
Mitsubishi ................. 2029, 2055, 2056, 2065, 2066, 2067,
2068, 2069, 2070, 2071, 2072, 2073,
2074, 2106, 2113, 2123
Montgomery Ward ............................................ 2075, 2132
Motorola ........................................................... 2021, 2132
MTC ................................................................... 2013, 2126
Multitech .............................. 2013, 2016, 2026, 2053, 2061
NEC ................. 2009, 2010, 2011, 2016, 2018, 2064, 2076,
2078, 2079, 2111, 2123
Nikko ........................................................................... 2014
Noblex ......................................................................... 2013
Olympus ...................................................................... 2021
Optimus ............................................................. 2014, 2132
Optonica ...................................................................... 2096
Panasonic .................. 2021, 2022, 2109, 2125, 2126, 2127
Pentax .................................. 2016, 2055, 2056, 2107, 2120
Pentex Research .......................................................... 2018
Philco ............................................. 2021, 2022, 2062, 2063
Philips ............................................ 2021, 2062, 2096, 2124
Pilot .............................................................................. 2014
Pioneer ................................ 2010, 2055, 2080, 2081, 2123
Portland ......................................... 2016, 2017, 2019, 2110
Proscan .................................................... 2000, 2001, 2131
Protec ........................................................................... 2061
Pulsar ........................................................................... 2104
Quarter ........................................................................ 2011
Quartz .......................................................................... 2011
Quasar ..................................................... 2021, 2022, 2125
RCA ................. 2000, 2001, 2003, 2013, 2021, 2055, 2056,
2082, 2083, 2084,2085, 2086,2087, 2088, 2089,
2090, 2091, 2107, 2115, 2120, 2125, 2131, 2132
Radioshack/Realistic .......... 2011, 2013, 2014, 2021, 2022,
2023, 2026, 2029, 2049, 2050,
2096, 2132
Radix ............................................................................ 2014
Randex ......................................................................... 2014
Ricoh ............................................................................ 2128
Runco .......................................................................... 2104
Samsung .................... 2005, 2013, 2015, 2033, 2053, 2112
Sanky ................................................................. 2104, 2132
Sansui ............................................ 2010, 2092, 2111, 2123
Sanyo ....................................................... 2011, 2013, 2023
Scott ....... 2012, 2015, 2025, 2032, 2038, 2065, 2093, 2116
Sears ............... 2011, 2014, 2021, 2023, 2048, 2049, 2050,
2051, 2055, 2056, 2107, 2118
Sharp ................ 2017, 2029, 2094, 2095, 2096, 2097, 2131
Shintom ......................................... 2004, 2056, 2061, 2098
Shogun ........................................................................ 2013
Signature ..................................................................... 2131
Singer ....................................................... 2021, 2061, 2128
Sony ............................................... 2004, 2098, 2099, 2119
STS ..................................................................... 2021, 2107
Sylvania ........... 2021, 2022, 2026, 2062, 2063, 2065, 2124
Symphonic ................................................................... 2026
Tandy ........................................................................... 2011
Tashiko ........................................................................ 2014
Tatung .......................................................................... 2111
TEAC ........................................................ 2026, 2085, 2111
Technics ............................................................. 2021, 2109
Teknika ................................ 2014, 2021, 2026, 2100, 2129
TMK ......................................................... 2013, 2024, 2047
Toshiba ............ 2015, 2049, 2051, 2055, 2065, 2093, 2116
ToteVision ......................................................... 2013, 2014
Unitech ........................................................................ 2013
Vector Research ............................. 2009, 2010, 2015, 2016
Victor ........................................................................... 2010
Video Concepts ................... 2009, 2010, 2015, 2016, 2113
Videosonic ................................................................... 2013
Wards .............. 2013, 2014, 2015, 2021, 2023, 2026, 2029,
2055, 2056, 2061, 2096, 2101, 2102, 2103,
2107, 2116, 2132
XR-1000 ................................................... 2021, 2026, 2061
Yamaha ................................ 2009, 2010, 2011, 2018, 2111
Zenith .................................. 2004, 2098, 2104, 2119, 2128
Cable Boxes
(Programmable for the SAT•CABLE and AUX buttons)
ABC ............................ 5002, 5003, 5004, 5005, 5006, 5053
Antronix ............................................................. 5008, 5009
Archer ...................................................... 5008, 5009, 5010
Cabletenna .................................................................. 5008
Cableview .................................................................... 5008
Colour Voice ...................................................... 5012, 5013
Comtronics .................................................................. 5014
Contec ......................................................................... 5016
Eastern ......................................................................... 5017
Garrard ........................................................................ 5011
GE ...................................................................... 5000, 5001
GC Electronics ............................................................. 5009
Gemini ............................................................... 5018, 5019
General Instrument ..................................................... 5003
Hamlin ....................... 5020, 5021, 5022, 5028, 5035, 5045
Hitachi ......................................................................... 5003
Jerrold ........................ 5003, 5018, 5023, 5024, 5046, 5053
Magnavox .................................................................... 5025
Memorex ..................................................................... 5026
Movie Time ................................................................. 5027
NEC .............................................................................. 5005
NSC .............................................................................. 5027
Oak .................................................................... 5016, 5029
Panasonic .......................................................... 5048, 5052
Philips .... 5011, 5012, 5013, 5019, 5025, 5030, 5031, 5032
Pioneer .............................................................. 5033, 5034
Proscan .............................................................. 5000, 5001
RCA ............................ 5000, 5001, 5007, 5047, 5049, 5052
Realistic ........................................................................ 5009
Regal .................................................................. 5022, 5035
Regency ....................................................................... 5017
Rembrandt ................................................................... 5003
Samsung ...................................................................... 5034
Scientific Atlanta ............................ 5006, 5036, 5037, 5038
Signal ........................................................................... 5018
Signature ...................................................................... 5003
Sprucer ........................................................................ 5052
Standard Components ...................................... 5039, 5044
Starcom .............................................................. 5018, 5053
Stargate ........................................................................ 5018
Starquest ...................................................................... 5018
Tandy ........................................................................... 5040
Teleview ...................................................................... 5014
Tocom ................................................................ 5004, 5023
Tusa ............................................................................. 5018
TV86 ............................................................................ 5027
Unika ................................................................. 5008, 5009
United Cable ............................................................... 5053
Universal .................................................. 5008, 5009, 5010
Viewstar ................................................... 5025, 5027, 5040
Zenith ................................................................ 5050, 5051
Satellite Receivers
(Programmable for the SAT•CABLE and AUX buttons)
Alphastar ..................................................................... 5079
Chapparal .......................................................... 5056, 5057
Dishnet ........................................................................ 5078
Drake ................................................................. 5056, 5059
Echostar ....................................................................... 5089
GE ...................................................................... 5000, 5001
General Instruments ............................... 5060, 5061, 5062
Panasonic .................................................................... 5075
Primestar ...................................................................... 5076
Proscan .............................................................. 5000, 5001
RCA .............................................................................. 5001
Realistic ........................................................................ 5063
Sony ............................................................................. 5072
STS1 ............................................................................. 5064
STS2 ............................................................................. 5065
STS3 ............................................................................. 5066
STS4 ............................................................................. 5067
Toshiba .............................................................. 5068, 5073
Uniden ............................................................... 5069, 5086
DVD Codes
(Programmable for the DVD and AUX buttons)
Aiwa ............................................................................. 3009
Hitachi ......................................................................... 3008
JVC ..................................................................... 3002, 3010
Konka ................................................................ 3011, 3012
Magnavox .................................................................... 3003
Mitsubishi .................................................................... 3004
Panasonic .................................................................... 3013
Phillips ........................................... 3003, 3019, 3021, 3022
Pioneer ........................................................................ 3005
RCA .................................................................... 3000, 3001
Sanyo ........................................................................... 3014
Shinco .......................................................................... 3001
Sony ......................................................... 3006, 3015, 3016
Toshiba .................................................... 3007, 3017, 3020
Zenith .......................................................................... 3018
Audio Codes
(Programmable for the AUX button only)
RCA and Dimensia
AM/FM ............................................................... 4003, 4270
AUX ............................................................................. 4004
Phono .......................................................................... 4005
Tape ............................................................................. 4006
CD ............................................................ 4007, 4190, 4211
Receivers
Aiwa ....... 4261, 4262, 4263, 4264, 4265, 4266, 4267, 4277
Denon .......................................................................... 4283
Harman Kardon .......................................................... 4276
JVC ............................................................................... 4268
JVL ............................................................................... 4276
Kenwood ..................................................................... 4269
Onkyo .......................................................................... 4278
Optimus ....................................................................... 4284
Panasonic .......................................................... 4279, 4280
Pioneer ........................................................................ 4275
RCA .............................................................................. 4270
Sherwood .................................................................... 4282
Sony ......................................................... 4271, 4272, 4281
Technics ............................................................. 4279, 4280
Wards ........................................................................... 4275
Yamaha .............................................................. 4274, 4275
28 Chapter 2
Using the Satellite
Receiver’s Features
Chapter Overview:
• What is a Program Guide?
• The interactive programming feature
• The Channel Banner and other on-screen displays
• How to use the on-screen programming schedule
Chapter 3
Changing Entertainment. Again.
29
Satellite Receiver Features
Current user profile
Current time and date
Program titles and information
Selectable
Advertisements
(highlight and select for more information).
Viewing
Suggestions
Active Profile’s
Preferences
Sorts by
Movies
Sorts by
Sports
Scroll down
AlphaSort™
Channel sort
Scout™
Anatomy of a Program Guide
The following diagram shows you the kind of information you will see in the program guides.
Displaying the Program Guides
To access the program guides, press MENU on the remote control and select
Program Guides, then the guide of your choice (Default, Channel, or Logo).
You can quickly access the receiver’s Default Guide by pressing the GUIDE button on the remote.
To change the current user, press the remote control’s WHO•INPUT button while viewing programming, then use the remote control’s arrow and OK buttons to select the desired profile. You can also press the remote control’s
MENU button, then select Program Guides, and then Select User to display the list of profiles from which to choose.
30 Chapter 3
Active Profile
Satellite Receiver Features
Program titles and information
Interactive content indicator
Dolby Digital and alternate audio indicators
Main menu AlphaSort™
System lock/unlock
Scout™
Mailbox
Caller ID
Viewing suggestions
Alternate audio
Program details
Using The Channel Banner
The channel banner appears whenever you do one of the following:
• Tune to a channel.
• Press the remote control’s INFO, SAT, or GO BACK buttons while watching programming.
• Press UP, DOWN, or INFO on the satellite receiver’s front panel.
• Exit the on-screen menu system.
On-screen icons represent frequently-used menu items. Some icons also change appearance to show the item’s status. Use the arrow buttons to highlight an on-screen item, and the OK button to select it. Some of the items you select in the channel banner can also be selected in the program guides.
Buttons of the Channel Banner
Main Menu icon
Takes you to the Main menu.
Locked icon
The system is locked. Spending, viewing and other limits cannot be accessed or changed.
Selecting this icon displays a password menu. Enter the correct system password to override settings.
Unlock icon
The system is unlocked. Spending, viewing and other limits can be accessed or changed.
Selecting this icon in the channel banner displays the Lock System control panel.
Video Unlock icon
A password has been entered to temporarily override the limits. The system will remain unlocked until the satellite receiver is turned off or re-locked.
Program Unlock icon
A password has been entered to override limits for a single program. After the program ends, or when the channel is changed, limits are restored.
AlphaSort™ icon
Enables you to sort titles alphabetically.
Scout™ icon
Allows you to search for programs using key words.
Mail icon
Displays the Mail screen. The icon will be white if you have an unread mail.
Telephone icon
Displays the Caller ID list screen. The icon will be white if you have received a new call but have not accessed the Caller ID List screen. It will be gray if you have accessed the Caller ID List screen.
Viewing Suggestions icon
Displays the Viewing Suggestions menu.
Program Details
Displays a description of the current program (if available).
Alternate Audio icon
Cycles through the alternate audio choices.
Chapter 3 31
Satellite Receiver Features
The DIRECTV INTERACTIVE™ Feature
Your digital satellite receiver includes DIRECTV INTERACTIVE™, powered by
Wink Communications
®
, a free service that gives you the opportunity to interact with TV programming and advertising. You can use your remote control to get program-related information, respond to free offers during commercials and even make purchases while you watch TV.
Whenever you see the DIRECTV INTERACTIVE™ icon ( ) appear, press the
OK/i button on the remote control to open the interactive window.
To learn more about the DIRECTV INTERACTIVE™ service:
1. Press MENU on the remote control (the Main menu appears).
2. Use the arrow buttons on the remote control to highlight Interactive.
3. Press the OK/i button to tune directly to the DIRECTV INTERACTIVE™
Center (channel 499) to get more information about the following: Getting
Started, Interactive Channels, Shopping Sign Up, Order History, Messages,
Help & Settings, and About DIRECTV.
Displaying On-screen Guides
Each time you press the remote control’s GUIDE button, a different type of program guide appears:
The Detail Guide
The Detail Guide shows five channels in a time-and-channel format, with program information for the highlighted program. A small window showing the program you were watching before entering the program guides is displayed in the upper left hand corner (you can preview other channels in the Detail Guide by highlighting channel numbers instead of the program titles).
Notes: By default, the Detail Guide appears when you press GUIDE on the remote control. You can change the default guide from the Detail Guide to the Grid Guide.
Select Personal Settings from the Main menu, then select the profile to be changed, then select Default Guide. Use the remote control’s arrow buttons to highlight Grid Guide, then press the OK button to activate your choice.
The Grid Guide
The Grid Guide shows seven channels in a time-and-channel format. A small window showing the program you were watching before entering the program guides is displayed in the upper left hand corner (you can preview other channels in the Detail Guide by highlighting channel numbers instead of the program titles).
32 Chapter 3
VCR1
ON • OFF
TV
DVD VCR2 AUX SAT
MUTE
CH +
SKIP
V
FETCH
GUIDE
CH -
GO BACK
INFO
OK
(-)
1
MENU
2 3
6
CLEAR
4 5
7 8
WHO•INPUT
0
REVERSE PLAY
9
ANTENNA
FORWARD
RECORD STOP PAUSE
Satellite Receiver Features
Getting Around In the Guides
This section describes how to change channels and move around a program guide.
CH +/-
Buttons
Arrow
Buttons
Digit Buttons (0–9)
You can point quickly to any channel in the program guide by entering the channel number with the digit buttons (0–9). For example, to point to channel
228, press the digits 2-2-8, on the remote control.
Scrolling Channel By Channel
The programs that you see on the TV screen make up one section—or page— of the total program guide. You can scroll one line at a time using the arrows: point to other times with the left and right arrows; point to other channels with the up and down arrows.
Digit
Buttons
Scrolling Page By Page
If you want to scroll up or down through the program guide faster, press the
CH +/- buttons on the remote control. The highlight scrolls a page at a time.
REWIND/
FORWARD
Buttons
Scrolling Forward and Reverse
To scroll forward in two-hour increments, press the remote control’s PLAY button while in SAT mode. To go forward or reverse by a 12-hour block of time, use the FORWARD and REVERSE buttons on the remote control.
Note: Your digital satellite receiver can store up to seven days of programming information. Getting all this information can take up to 12 hours to download.
Chapter 3 33
Satellite Receiver Features
Tip
For information on tuning to a PPV program, see pages 47.
Tip
Your digital satellite receiver can store up to seven days of information, so retrieving data can take a little time.
It can take up to 12 hours to download all seven days of information when turning the system on after the Guide information has been lost.
Tuning to a Program
To tune directly to a current program listed in the guide, point to the program and press OK.
To see information about a program in the guide, point to the program and press INFO.
Then, you can select:
• View Channel to tune to that channel
• Record Program to record the program
• Remind Me to set up a Watch Timer. This will display a prompt allowing you to quickly change the channel when the program is about to begin.
• Other Times to see what other times the program is available.
• More Details opens another display with detailed information (if available).
The options available to you may vary according to the type of program you select.
More Details
There’s a variety of program information sent along with standard broadcast signals, and your digital satellite receiver can display much of it (if available).
The More Details menu can offer information (if available) about Actors and
Roles, the Director, the Writer, Original Materials, the Production Studio,
Awards, Keywords associated with the program, and the original release Date and Run Length. Just use the remote control’s arrow and OK buttons to highlight and select the desired button, and to display more information.
You can even use the displayed information in the More Details menu to look for matching information in the stored guide programs, or to create search criteria for use with the Scout™ search feature of your digital satellite receiver.
To Access More Details:
1. Highlight a desired program in the on-screen guide and press the remote control’s INFO button.
2. Highlight and select More Details.
Note: The More Details button is displayed in the Program Details menu only if more information is available.
3. Highlight and select the desired on-screen information button to display the details on the opposite side of the screen.
To search for other programs with similar information:
4. Highlight the desired information on the right side of the menu and press the remote control’s OK button. This will display any other program stored in the on-screen guides that shares the highlighted information.
To save your search as Scout Criteria:
5. After completing step 4, use the remote control’s arrow and OK buttons to select the Save as Scout button. You will be given on-screen instructions to complete this task.
34 Chapter 3
Satellite Receiver Features
Additional Program Guides
Besides the Detail and Grid Guides, there are a few more to choose from: the Channel Guide, the Logo Guide, and the Viewing Suggestions Guide.
You can access these guides from the Main menu by selecting Program Guides.
The Channel Guide
Displays the programming schedule for the selected channel.
The Logo Guide
Displays channel logos for the current user’s channel list.
The Suggestions Guide
Displays a list of programs based on programming that has been previously watched under that user profile.
Chapter 3 35
Satellite Receiver Features
Sorting the Guides
Sorting the guide is a way of organizing the information to show only the types of programs that interest you. There are several on-screen icons that sort the guide in different ways. You can list programs by sports or movie themes, for example. You can customize the themes to meet your tastes, and each profile can have its own default program sorting.
To get to the sorting icons, use the down arrow button to move the highlight to the icons at the bottom of the screen. Then, use the left and right arrow buttons to highlight the desired icon.
TIP: Accessing Viewing
Suggestions
You can select Viewing Suggestions by selecting Suggestions in the Main menu, or by pressing the icon displayed in the channel banner or on-screen guides.
Viewing Suggestions
When you select the Viewing Suggestions icon, a list of recommended program events appears. The recommendations are based on your previous viewing habits in terms of the amount of time spent watching programs that match a topic and theme category. The suggestions are ordered by best match.
Viewing suggestions are created for each active user profile. The suggestions being shown are always for the current user profile.
You can view and change your suggestions, or turn the digital satellite receiver’s learning behavior off altogether from the Viewing Suggestions menu.
To Access the Viewing Suggestions Menu:
1. Press the remote control’s MENU button to display the Main menu.
2. Press 1 to select Program Guides.
3. Press the 4 button to choose Suggestions.
4. Access desired viewing suggestions using the remote control’s arrow and
OK buttons to select.
Note: You can also access this menu by selecting the Viewing Suggestions icon in the Channel Banner or at the bottom of the on-screen guides.
Customizing Viewing Suggestions
You can edit the themes that will appear in the Viewing Suggestions menu by applying different “weights” to the topics. Increasing a topic’s weight increases the chance that programs with such themes will appear in the Viewing
Suggestions menu. Decreasing a theme’s weight will lessen the chance that such themes will appear.
To Change the Weight of Themes and/or Topics:
1. Follow steps 1-3 above to display the Viewing Suggestions menu.
2. Press the 2 button to select Edit Topics.
3. Select the numbered Topic to edit, then use the remote control’s arrow and
OK buttons to select and adjust weight percentages.
36 Chapter 3
Chapter 3
Satellite Receiver Features
Active Profile’s Preferences
Each individual can edit preferences so customized themes and topics appear when a sorting icon is pressed. The Active profile’s preferences can be quickly accessed by selecting this icon at the bottom of all on-screen guides.
To Change the Active Profile’s Preferences:
1. Press the GUIDE button on the remote control to display the default guide.
2. Use the remote control’s arrow and OK buttons to select the Active Profile
Preferences icon at the bottom of the guide.
3. Press the 2 button to select Edit Preferences. This will display a menu where you can customize the themes to appear when the Active Profile’s
Preferences icon is selected.
4. In the customizing menu, use the remote control’s arrow and OK buttons to highlight and select/deselect theme choices.
Note: The themes and topics can be customized for any profile.
Once finished customizing the themes, only topics that match your choices should appear when you select the active profile’s preferences icon in the on-screen guides.
Movies
Select the Movies icon to sort and list only movies. After selecting Movies, the
Movies Themes menu is displayed. Here you can sort movies by various themes.
By default, All Movies is highlighted first.
Select the Movies Themes icon to sort the guide to list specific types of movies, such as comedies or musicals. This icon may change from Movies to a different topic in the future, but it will continue to function in the same way.
Sports
Select the Sports icon to list sporting events only. After selecting Sports, the
Sports icon changes to a Sports Themes icon.
Select the Sports Themes icon to sort the guide to list specific types of sports, such as basketball or soccer. This icon may change from Sports to a different topic in the future, but it will continue to function in the same way.
Channel Sort
Sort the on-screen guides to display channels in either numeric or alphabetical order. When the guide is sorted alphabetically, the 1-2-3 icon is displayed (select the icon to change the display to numeric). When the guide is sorted numerically, an A-B-C icon is displayed (select it to display the guide alphabetically).
37
Satellite Receiver Features
Tip
On-screen icons represent the status of the Scout feature:
This icon (displayed in the Scout menu) indicates that the information you specified has been found.
The Scout icon in the
Channel Banner and the on-screen guides will have a white outline when a Scout search returns information.
AlphaSort™
The AlphaSort feature lists all the program titles stored in the current guide in alphabetical order. Select the AlphaSort icon to search for specific program titles that are in the stored program guide in alphabetical order. Use the arrow buttons on the remote control to highlight a character, then press OK.
For example, to search for the program Auto Racing, point to and select “A.”
(Words like “The,” “A,” and “An” appear at the end of a title.) All titles that begin with “A” appear in the AlphaSort list. Next, enter the letter “U.” All titles beginning with “AU” appear in the list.
Continue to enter the specific title until it appears in the AlphaSort list. If you enter the wrong character, select either Backspace or Clear All.
Use the arrow buttons on the remote control to highlight the title you are looking for. Press the OK button to select it (if the program is airing), or the
INFO button to see more information (if the program is not airing, OK will act like the INFO button). The AlphaSort feature looks for titles from all stored programming.
Scout™
The Scout system icon lets you assign “Scouts” to search the guide for specific program information, such as actors’ names or program descriptions.
Select the Scout icon from a program guide to view the available Scout menu items. Then, select New Scout from the Scout menu (this button only appears if there is an empty Scout menu available).
Select Enter Text to set up the information the Scout feature will look for in the program guide. Use the on-screen keyboard to enter the desired search parameters. You can also use the Select Fields menu button to specify the type of information you are looking for.
For example, if you are interested in how to prepare food, enter a common term you think would occur in program information, like “cooking.” When you have finished entering your topic select Run Scout.
If “cooking” appears within a program title or program description, the program will be included in the Scout Results program list.
Once you have set up a Scout menu item, you can check its status by highlighting it. A highlighted binoculars icon means that a Scout menu item has found results.
Scout continually searches for requested information whether the box is on or off. You can also select Run Scout to do an immediate search after setting up a scout.
Check a Scout menu item’s results by selecting that Scout menu item. When you highlight and select that Scout, the results are displayed on the right side.
Down Arrow
The down arrow icon allows you to scroll down through other channels in the guide. Point to the down arrow icon and then press OK to scroll down through the program guide.
38 Chapter 3
Using the
Menu System
Chapter Overview:
• Using the Menu System
• Program Guides
• Messages
• Using the Purchases Menu
• Recording with Timers
• User Profiles
• Personal Settings
• System Setup
Chapter 4
Changing Entertainment. Again.
Graphics contained within this publication are for representation only
39
Using On-Screen Menus
Using the Menu System
To display the Main menu, press MENU on the remote control.
To use the menu system, you need to use the remote control’s arrow buttons to highlight your on-screen choice, then use the OK button to select it. In menus that use numbered choices, you can use the remote control’s number buttons to select an item quickly.
Tip: No Menus?
If the Main menu doesn’t appear when you press MENU, the remote control might not be in SAT mode.
Try pressing the SAT button on the remote, and then MENU.
Tip: Using On-screen Help
Press the remote control’s INFO button at any time for more information.
On-screen Buttons and Context Help
The on-screen menu system offers you more than one way to get more information or to navigate within the system using the on-screen Go Back and
Help buttons at the top of most menus.
Exiting a Screen
There are three ways to exit a menu:
• Select the on-screen Go Back button and press the OK button on the remote control.
• Press the CLEAR button on the remote control. The on-screen display clears from the screen and you return to TV viewing.
• Press the GO BACK button on the remote control. This returns the TV to its preceding display.
Getting Help
For an overview of a displayed menu, use the remote control’s arrow and OK buttons to select the on-screen Help button (?).
For details about a highlighted menu item (in what context an on-screen button is used, for example), press the remote control’s INFO button and a popup window will tell you more.
40 Chapter 4
Using On-Screen Menus
Tip: Don’t Be Afraid to
Explore
Once you’ve learned the basics, feel free to poke around the menu system– exploring this system is a great way to learn!
Remember to use you remote control’s arrow and OK buttons to maneuver through menus.
And, so you don’t worry about getting lost in the menus, you can press CLEAR at any time to leave the menu system and return to regular system viewing.
Main Menu Items
This section briefly describes each of the options available from the Main menu.
More information about each menu and its features is included later in this chapter, and you can always get more information when an item is highlighted by pressing the remote control’s INFO button.
Program Guides
Selecting this button will display a menu with a variety of different ways to view program guide information.
Messages
This button is used to access the Caller ID information from your telephone company and mail messages from DIRECTV.
Note: You must subscribe to Caller ID service from your telephone service provider in or der for the on-screen Caller ID information to be displayed.
Purchases
Use this button to review or cancel upcoming purchases, review past purchases, and set spending limits for saved profiles.
Timers
Schedule the digital satellite receiver to tune to a specific channel at a specific time. If a VCR has been properly connected to the receiver, you can also record future programming.
Profiles
This button displays a menu where you can set system and user passwords, ratings limits, spending limits, viewing hours, as well as create favorite channel lists.
Personal Settings
Do you want to set up an individual profile’s personal settings or alter the look and feel of an existing profile? This button will take you to a menu where you can alter or set personal preferences of your digital satellite receiver.
System Setup
Allows you to adjust to the way your system works, to get more information about system features, get dish pointing coordinates, etc.
Interactive
Television broadcasts typically carry a wealth of information and now you can access and interact with it starting with this button. Selecting Interactive from the Main menu displays the DIRECTV INTERACTIVE™ Center for setting up interactive TV service.
Chapter 4 41
Using On-Screen Menus
Active profile
Current time and date
Program titles and information
42
Selectable
Advertisements
(highlight and select for more information).
Viewing
Suggestions
Sorts by
Movies
Active Profile’s
Preferences
Sorts by
Sports
Scroll down
AlphaSort™
Channel sort
Scout™
The Program Guide
Note: The program guide is described in detail in the previous chapter, Using
the Satellite Receiver’s Features, starting on page 29.
Selecting Program Guides from the Main menu displays a menu with a variety of display options available. You can select a specific User Profile, the system default guide (Detail Guide or the Grid Guide- according to your preferences), or the Logo or Channel Guide, Viewing Suggestions, or change the active profile.
Anatomy of a Program Guide
The diagram above shows you the kind of information you will see in the
Detail Guide and Grid Guide (Grid Guide shown here).
Displaying Program Guides
In addition to selecting Program Guides in the Main menu, you can press the
GUIDE button on the remote control. This bypasses the Program Guides menu and directly displays the default guide.
Chapter 4
Chapter 4
Using On-Screen Menus
Messages
The Messages menu lets you access messages or phone calls. If you select Mail, it shows you messages that are sent from DIRECTV. For example, you may receive a message calling your attention to a new service. If you select Caller
ID, this menu shows you Caller ID information from your telephone provider (if you subscribe to Caller ID service).
To tell if you have mail, you need to check the channel banner available when you press the remote control’s INFO button. In the channel banner, the messages icon will be highlighted if you have an unread message waiting.
Checking Your Mail
Select Messages from the Main menu, then Mail from the next menu. Or select the mailbox icon on the channel banner to view your mail.
1. Point to a message and press OK. The message is opened for you to read.
2. Press OK again to close the message.
If you want to erase a message, point to Erase Message and press OK. When you exit Messages, messages that aren’t erased are saved in memory.
Note: The quickest way to check for messages is to press the INFO button on the remote control. This will display the channel banner. With the channel banner displayed, use the remote control’s arrow buttons to highlight the mail icon, then press the remote control’s OK button to access the Mail menu.
43
Using On-Screen Menus
Caller ID
Your digital satellite receiver is capable of displaying and storing Caller ID information provided by your local telephone company. To use this feature, you must have your receiver directly
plugged into a telephone outlet (or a RC930 wireless modem) and you must subscribe to
Caller ID or similar caller identification services from your telephone company.
Your Caller ID enables you to:
• Identify callers before you answer the phone.
• View the time and date of each incoming call.
• Record the Caller ID information of up to 20 incoming calls sequentially.
Note: Only the last ten calls will be retained after a power outage.
• See who called while you were away.
There are two ways to access the Caller ID menus: by selecting Messages from the Main menu, or by pressing INFO on the remote control and selecting the telephone icon in the Channel Banner.
The icon will be white if you have received a new call but have not accessed the Caller ID List screen. It will be gray if you have accessed the Caller ID List screen.
Setting Up Caller ID
To set up your Caller ID, go to the Main menu and select Messages, then select
Caller ID Setup. Use the up and down arrow and OK buttons to select your preferences.
Caller ID Light
Setting Caller ID Light to On causes the front panel light to flash if you receive new calls while the digital satellite receiver is off. The light will flash until you turn the receiver on.
Caller ID Message
Setting Caller ID Message to On displays the on-screen
Caller ID banner when a call is received. You may want to turn this feature off when you are recording manually and do not want the on-screen messages to appear on your recordings. Your calls will be stored in the Caller ID List screen even when Caller ID is turned off.
Caller ID Message Time-out
Set the amount of time (from 1–30 seconds) that the Caller ID banner will display when you have an incoming call. For this feature to work, make sure Caller ID Message is set to On.
Note: If you have a timer set to either watch or record, the Caller ID banner will be temporarily overridden for the duration of that timer. When the timer event is over, the Caller ID banner will display as selected under Caller
ID Message.
When viewing or recording manually (not using a timer) the Caller ID banner will display (and be recorded if recording) as selected under Caller ID
Message.
At all times Caller ID messages will be stored in the Caller ID List screen
(unless a call arrives when you are on the telephone and you do not have a
Type II box or Type II service).
44 Chapter 4
Tip: When you have unread
Caller ID calls:
The front panel light will flash (when the digital satellite receiver is off)
The telephone icon in the channel banner will be highlighted white
Tip
If you’d like more information to appear in your Caller ID banner and call list, or if you’d like to subscribe to Caller ID, check with your local phone company about the availability of different types of Caller ID service.
Using On-Screen Menus
Receiving Calls
When your phone rings twice and Caller ID Message is set to On, a banner appears at the bottom of the screen.
The banner may include the phone number, date, and time; or the name, phone number, date, and time. The banner information depends on the type of service your telephone company provides.
The Caller ID banner will override closed captioning at the bottom of the screen and will appear for the amount of time selected in the Caller ID Setup screen.
The Caller ID banner will not be displayed if you are in the menu system or a timer is active when you receive a call.
Note: If using your telephone and another call arrives, the new call’s information won’t appear in the banner or be recorded in the Caller ID List screen unless you have type II service and a type II Caller ID box in your house.
If you have a timer set to either watch or record, the Caller ID banner will be temporarily overriden for the duration of that timer. When the timer event is over, the Caller ID banner will display as selected under Caller ID Message.
When viewing or recording manually (not using a timer) the Caller ID banner will display (and be recorded if recording) as selected under Caller ID
Message.
At all times Caller ID messages will be stored in the Caller ID List screen
(unless a call arrives when you are on the telephone and you do not have a
Type II box or Type II service).
Message Indicators
The following is text that may appear in the incoming Caller ID banner and call list.
Out of Area
The name and/or phone number of the incoming call is coming from outside the local area.
Private Name
The name of the incoming call is sent as “Blocked” from the phone company.
Private Number
The phone number of the incoming call is sent as “Blocked” from the phone company.
Unknown Name
The name of the incoming call is not provided by the telephone company or the information is unreadable.
Unknown Number
The number of the incoming call is not provided by the telephone company or the information is unreadable.
Note: To clear the Caller ID banner from the screen, press CLEAR on the remote control.
Chapter 4 45
Using On-Screen Menus
Tip: Don’t Forget About the
CLEAR Button
Press the CLEAR button on the remote control to remove the on-screen menus and return to normal viewing.
The Caller ID List Screen
The digital satellite receiver can store up to 20 call entries in the Caller ID List screen. When the memory is full, a new call automatically replaces the oldest call in memory. The list also tells you if you have received multiple calls from the same number.
To access the call list:
• Select Caller ID List from the Messages menu, or
• Press the INFO button on the remote control and select the phone icon.
Deleting Calls
From the Caller ID List screen, you can delete entries:
1. Highlight the call you wish to delete and press OK.
2. A crumpled paper icon appears to indicate that you wish to delete the call.
3. To permanently delete the call, exit the screen. If you change your mind before exiting the screen, highlight the call then press OK to restore it. The crumpled paper icon should disappear.
Using the Purchases Menu
The Purchases menu allows you to review upcoming and past purchases and set spending limits.
The list of purchases may be longer than one screen; use the up and down arrow buttons to see more items. The display also shows the title, channel, date, time, and cost of each program.
Note: The Past Purchases list is updated as soon as a purchased program is viewed.
Reviewing and Canceling
Upcoming Purchases
Highlight and select an upcoming purchase from the Future Purchases screen.
You can review the program description, as well as cancel an upcoming purchase.
46 Chapter 4
Using On-Screen Menus
Spending Limits
Use the Spending Limit option to indicate a per-event, and/or a monthly spending limit for Pay Per View programs.
1. Select Spending Limit.
2. Select the user profile you’d like to set a spending limit for, then use the digits or the arrow buttons on the remote control to enter program spending-limit information.
After a spending limit is set and the system is locked, you must enter a password to purchase a Pay Per View program that costs more than your spending limit allows.
Note: Spending limits are in effect only when the system is locked. See
“Locking the System,” later in this section, for details.
Pay Per View Programs
Pay Per View (PPV) programs are DIRECTV
®
programs that you can purchase— like a movie ticket—if you subscribe to DIRECTV
®
programming and have your digital satellite receiver connected to a telephone line (see the instructions starting on page 5 for connection details).
Tip: Ordering PPV
If you want to order PPV programs using the on-screen menus, you need to connect your digital satellite receiver to a telephone line.
Tip: PPV Passwords
You may need to enter your four-digit password to order a PPV program if it costs more than the spending limit you set up in the Profiles or Purchases menu.
Previewing and Purchasing
You can preview and purchase DIRECTV
®
Pay Per View movies and events if you subscribe to DIRECTV
®
programming and have your digital satellite receiver connected to a telephone line.
To purchase a movie or event, you can take one of two actions:
• Tune to a PPV channel using the remote control’s CH +/- buttons. When you find one, press the INFO button to find more information and details about how to purchase the program.
• Highlight a PPV program in a program guide and press INFO. The Program
Details screen will appear and give you more information about the program.
From this screen you can also purchase the program.
You can select:
• View Channel to view that channel
• Buy Program to purchase the program
• Buy and Record to purchase the program and set a timer to record it
• Remind Me to be prompted just before the show is scheduled to start.
Note: The options available to you may vary according to the type of program you select.
Chapter 4 47
Using On-Screen Menus
Key
On-screen icons are a quick way to understand the timers:
Indicates that the timer is set.
Indicates that the timer is set for a PPV program.
Indicates a timer conflict.
Indicates Interactive content.
Timer Recordings
The Timers feature allows you to preset your digital satellite receiver to automatically tune to a particular channel at a predetermined time.
To use the Timers feature, select Timers from the Main menu. Select a Timer
(1–16) and then use the arrow buttons to complete the on-screen details. When the information is complete, select Continue.
Note: If you subscribe to Caller ID service, note that the Caller ID banner will neither be displayed or recorded during a timer (watch or record). However, all calls will be logged. The banner will display as selected when the timer recording is over.
Setting Up a Timer
The Timers feature allows you to set up timer recordings if you have connected the VCR Controller to your digital satellite receiver and told the receiver what type of VCR you are using. See page 19 in the Setup and Connections section for details on connecting a VCR Controller.
Editing or Canceling a Timer
From the Timers screen, select the Timer you want to edit or cancel, and then do the following:
• Use the arrows buttons to edit the Timer, then select Continue.
• Select Clear Timer to cancel the timer.
• To watch the program daily or weekly, edit that program’s Timer.
Recording with a Timer
If you choose Record instead of Watch when setting a Timer (and have set up your VCR as previously discussed), the Timer will turn on your VCR, then start and stop recording a program.
To record with timers:
• Your VCR must be tuned to channel 3 or 4 (if the VCR is connected with just coaxial cables), or to the video input channel (if the VCR is connected with audio/video cables).
• You must turn your VCR off prior to the scheduled recording time.
• You must have a recordable tape in the VCR.
48 Chapter 4
Chapter 4
Using On-Screen Menus
Schedule a Timer with the RECORD
Button
You can schedule a recording directly from the guide.
1. With a program highlighted, press the RECORD button on the remote control. The Program Details screen appears.
2. To schedule a timer to record, select:
• Record Program to set a timer to record the program, or
• Buy and Record to purchase the program and set up a timer to record the program.
Note: Programs bought to be recorded may have a different purchase price than those bought for viewing only.
User Profiles
Profiles allows you to set up different channel lists and limits for the different members of your family. A main profile (the Family Profile) and up to four separate profiles can be created. Individual settings that can be changed in the
Profile Menu include the profile name, viewable channel lists, ratings limits for
TV and movies, viewing hours, spending limits, and profile locking.
Creating and Editing User Profiles
When you select Profiles from the Main menu, the first screen you see presents a menu listing all user profiles (the Family Profile and up to four individual profiles). You can create a new profile (if a blank profile exists), or edit an exiting one.
To personalize an individual User Profile:
1. Press the remote control’s MENU button to display the Main menu.
2. Press the 5 button to select Profiles.
3. Highlight the desired User Profile.
Note: The highlighted User Profile’s settings are displayed in the panel on the right side of the screen.
4. Press the remote control’s OK button to select that profile and enter profile editing mode.
49
Using On-Screen Menus
Setting the Profile Name
The first step when creating a new profile is to set a name. This will be the name that appears when repeatedly pressing the WHO•INPUT button.
To set the profile name:
1. In the Profiles menu, press the 1 button to select Name.
2. Use the remote controls arrow and OK buttons to highlight and select the different letters of the profile name.
Copying Profile Settings
To make creating or editing a profile easier, your digital satellite receiver gives you the ability to use the settings of a previously set profile.
To copy the settings of an existing profile:
1. In the Profiles menu, press the 2 button to select Copy Settings.
2. Use the remote control’s arrow buttons to select the proper profile to copy settings from.
3. Press the remote control’s OK button to select the desired profile.
4. Use the remote control’s arrow and OK buttons to highlight and select the
COPY button at the bottom of the screen.
Creating a Profile Channel List
1. Select Edit Channels.
2. Use the arrow buttons to highlight a channel, and press OK to remove (or replace) the check mark. Checkmarked items appear in the channel list.
Add or Delete All Channels
You might be able to save time when creating a channel list by using the Add
All Channels option or the Delete All Channels option before removing or adding individual channels.
Also, program providers may make additional channels available. To prevent new channels from appearing in a profile channel list, choose Delete All
Channels and checkmark only the channels you want to appear in the list.
Subscriptions
Selecting the Subscriptions button will allow you to uncheck and remove from the channel list all channels that you do not subscribe to. Use the remote control’s arrow and OK buttons to select the desired on-screen menu buttons.
Note: This step may take several minutes to complete.
50 Chapter 4
Important
You need to lock the system in order for rating limits, channel limits, viewing hours, and spending limits to go into effect.
After you lock the system, you need to enter the system password to edit the limits. See “Locking the System,” later in this section, for details.
Using On-Screen Menus
Setting the Rating Limit
The Rating Limit menu enables you to set a maximum rating viewing limit for rated movies (based on the MPAA rating system) and TV programs. Unrated movies and TV programs can also be restricted from individual profiles.
1. In the Profiles menu, select Rating Limits.
2. Highlight the desired rating feature to set (Movie Ratings, TV ratings, or Not
Rated Events).
3. Press the remote control’s OK button.
4. Use the up and down arrow buttons to move the rating selector to the highest desired rating to be viewed by all profiles.
Notes: In the TV Ratings menu, you can customize aspects of certain ratings.
For example, the TV-14 rating has four check boxes beside it. Each of these boxes can be checked or unchecked for greater customizing.
The boxes beside certain TV ratings boxes stand for Fantasy Violence (FV),
Dialogue/Adult Situations (D), Language (L), Sex (S), and Violence (V).
After the Rating Limit is set and the system is locked, you must enter the system password to watch programs with a rating higher than your limit.
Viewing Hours
Use the Viewing Hours option to limit the total amount of time, as well as the time of day, that a user can watch programming.
1. In the Profiles menu, select Viewing Hours.
2. Use the digits on the remote control or point to the + or – buttons and press
OK to complete the on-screen sentence. Choose the days to view, how many hours can be viewed each day (0–24 hours) and when programming can be viewed. Be sure to lock the system for these limits to take effect.
Setting Up Spending Limits
Select the Spending Limit option to indicate a per-event and/or a monthly spending limit for Pay Per View programs.
1. Point to Spending Limit, and press OK.
2. Use the number buttons on the remote control to enter a single-program spending limit and a monthly spending limit (if desired).
3. When all fields are set up correctly, the satellite receiver returns to the previous display.
Note: After Spending Limits are set and the system is locked, the system password will be required to purchase a Pay Per View program that costs more than the set Spending Limits allow.
Chapter 4 51
Using On-Screen Menus
Locking a User’s Profile
Users can be assigned a personal password to lock their profile. When a password is assigned, users must enter the password before they can view programs using that profile. Profile passwords do not allow access to, or editing of, the profile limits (you must enter the system password to edit profile limits).
Note: Each profile that can be easily accessed using the WHO•INPUT button on the remote control.
To lock an individual profile:
1. In the specific profile edit mode, select Lock User.
2. Use the arrow or digit buttons to select each digit of the password.
Locking the System
Locking the system puts the ratings, spending, viewing, and channel limits you have set up for each profile into effect. When you lock the system, no one can modify any of these settings without first entering the four-digit system password.
1. In the Profiles menu, select Lock System.
2. Use the arrows or the digit buttons to enter a four-digit system password.
3. Enter the password a second time to confirm it. The lock icon should be displayed in the channel banner.
Notes: After the system has been locked, you must enter the correct password in order to access the Edit Profiles control panel.
If you forget a USER password, you need to unlock the system and then assign a new user password. If you forget the SYSTEM password, contact the
DIRECTV authorization center.
• Lock icon: All limits are in effect. No limits can be accessed or changed without first entering password system. A password is required to override limits or access the system.
52 Chapter 4
Using On-Screen Menus
Unlocking the System
When the system is unlocked, the channel, spending, viewing, and ratings limits that you set are no longer in effect. To unlock:
1. Highlight and select Unlock System in the Profiles menu.
2. Highlight and select Yes to confirm that you want to unlock the system. The unlock icon should be displayed in the channel banner.
When you attempt to access a channel that is blocked by one or more limits (and the system is locked), you will be asked to override limits by entering the four-digit system password.
If you enter the password to override a limit, all limits are unlocked until you turn off the digital satellite receiver. When you turn on the receiver again, the system will be locked, and the
Family profile channel list will be selected. If you want to re-lock the system without turning off the receiver, you can select the lock icon in the channel banner.
Program/Video Unlock
If the system is locked and you want to access a blocked program without unlocking all settings, press the remote control’s INFO button and highlight the
Lock icon in the channel banner. Make sure to check the box beside Unlock this
program only, and enter the system password. This program is no longer blocked, but all other settings remain in effect. The unlock icon with a P should be displayed in the channel banner.
• Use the Lock and Unlock icons in the Channel Banner to lock or unlock the system. To access the Lock/Unlock Menu, press the INFO button on the remote control and use the arrow buttons to select the Lock icon. Use the remote control’s number buttons to enter the proper password and follow on-screen instructions.
• Unlock icon: The system is unlocked. No limits are in effect. Spending, viewing and other limits can be accessed and changed.
• Unlock (with a P) icon: The system is locked, but no limits are in effect for the duration of the current program because a password has been entered to override the current program’s limits. No limits can be accessed or changed. After the program ends, the system will return to Lock status.
• Unlock (with a T) icon: The system is temporarily unlocked with no limits in effect until the receiver is placed in standby mode. A password has been entered to override the system limits. No limits can be accessed or changed without entering the system password. When the system is turned off, the it will return to Lock status.
Chapter 4 53
Using On-Screen Menus
Choosing Your Profile
Each time you turn on the digital satellite receiver, the Family profile is selected by default, so this should be the profile with the most restrictive limits you want enforced across all profiles.
To select another profile:
1. Press the WHO•INPUT button to display a list of profiles.
2. Use the remote control’s arrow and OK buttons to select the desired profile.
Then enter the four-digit password to activate the profile.
Note: If the profile is not password protected, you can just press OK to activate it.
The channels, spending, rating and viewing limits associated with the chosen profile will be active only when the system is locked.
The active profile also affects what you see in the program guides. Selecting the
User Preferences icon sorts the guide to show only programs meeting the current user profile criteria and which personal settings are used.
To change the current profile, press the WHO•INPUT button.
Personal Settings
The Personal Settings menu, accessed by pressing the 6 button in the Main menu, lets you customize the look and feel of the active profile. Each of the satellite system’s profiles can have individualized personal settings.
Note: If a personal profile is password protected, then that password must be entered before changing any of the profile’s settings.
Once you have accessed the personal settings menu, select the desired profile.
You will use the remote control’s arrow and OK buttons to make your selections.
The following sections explain your options when changing your personal preferences. Follow the on-screen instructions to make changes to the system.
Name
Used to change the profile display name. This name will be displayed in the
Profiles menus as well as when the remote control’s WHO•INPUT button is pressed.
Note: A profile’s name can be changed either by selecting the Personal
Settings in the Main menu, and then selecting Name, or in the Profiles edit menu.
Default Guide
Lets you choose which guide appears first when you press the GUIDE button on the remote control. The choices are Grid Guide or Detail Guide.
54 Chapter 4
Using On-Screen Menus
Guide Sorting
Lets you choose whether the default guide is sorted numerically by channel numbers or alphabetically by channel names.
Color Scheme
Lets you pick which colors appear in the guide and menu systems.
Translucency
Lets you choose how see-through the channel banner, the Fetch menu, and the Main menu are when displayed. Use the remote control’s arrow buttons to access and slide the indicator bar to make the screens more or less opaque.
Animation
Lets you select which graphics are displayed when you tune to an audio-only channel and also lets you select the animation time-out.
Edit Fetch
Lets you choose a single function for the FETCH button on the remote control, or to bring up a custom menu of up to 8 different features to choose from.
To create a custom Fetch menu:
1. Press MENU to bring up the Main menu.
2. Select Personal Settings,
3. Select the desired profile (each profile can have a different Fetch Menu).
4. Select Edit Fetch.
5. Select Fetch Control.
4. Select Show Fetch Menu.
6. Select Fetch List from the Edit Fetch menu.
7. Choose up to eight menu items to include in your customized menu by checkmarking them with the OK button.
8. Press the left arrow button to confirm your selections and return to the menu.
When you would like to access your customized menu, press the FETCH button on the remote control.
Chapter 4 55
Using On-Screen Menus
TIP: Getting Help
If you ever have a question about the menu you are in, select the on-screen help button (?). If you have a questions about a highlighted menu item, press the remote control’s INFO button.
To assign one function to the FETCH button:
1. Press MENU to bring up the Main menu.
2. Select Personal Settings,
3. Select the desired profile (each profile can have a different Fetch Menu).
4. Select Edit Fetch.
5. Select Fetch Control.
4. Select Assign One Function.
5. Select Fetch List from the Edit Fetch menu.
6. Choose which menu item you would like to assign to the FETCH button by pointing and selecting.
7. Press the left arrow button to confirm your selection and return to the menu.
You may press the FETCH button on the remote control and execute the assigned function at any time while viewing DIRECTV ® programming.
INFO Help
A text block saying Press INFO to learn more pops ups by default whenever there is a brief period of inactivity in a menu. This INFO Help menu allows you to turn this feature on or off.
Reset
This button allows you to reset all personal settings back to the factory defaults.
System Setup
The System Setup menu allows you to get details about your system and is used to configure system options that are not profile specific. Setup items that are global to the digital satellite receiver include system options and dish pointing.
Assisted Setup
This feature walks you through a series of questions and is designed to quickly get the system detecting a signal.
Follow the on-screen instructions to set the system language, get instructions on menu navigation, select the type of satellite dish antenna used, find your dishpointing coordinates, and run a system test that initiates diagnostic procedures on the satellite receiver system. You have the option to skip any of the steps.
56 Chapter 4
Using On-Screen Menus
System Index
The System Index feature allows you to get detailed information about your digital satellite receiver.
Details that can be viewed from within the System Index menu include program guide information, details about the menu system, explanations of the remote control, front panel, and back panel of the receiver, and even a glossary of words common when discussing digital satellite receivers.
System Options
The System Options feature allows you to set a default on-screen display language, identify the type of VCR to be controlled by the receiver, choose a receiver output channel (the channel that the TV views satellite broadcasting), set up the remote control, select a default picture size, select a Dolby Digital option, and set the time zone.
Use the remote control’s arrow and OK buttons to navigate through these menus, or you can use the digit buttons on the remote control to select a numbered on-screen item.
Languages
This menu allows you to select menu and audio languages. You can choose between English and Spanish for the menu language.
You can choose from a variety of audio languages to be heard if a program is simulcast in that language. If that language is not available for that broadcast, the programming will be heard in its default language.
Set VCR Type
Use the arrow, OK, and number buttons of the remote control to follow the menu options displayed when you select the Set VCR Type menu button. These screens will allow the digital satellite receiver to control a properly attached
VCR.
Selecting this button transfers you to a Set VCR Type menu with a scrollable list of manufacturers displayed in alphabetical order. Scroll to the proper manufacturer, and a list of codes appears. Use the remote control’s arrow and
OK or the corresponding number button to select one of the options.
Notes: If you select Code Search from the list of codes, the satellite system will automatically try every code in the list until the proper one is used.
If you do not see your VCR manufacturer’s name, select Other (at the bottom of the list) and enter the appropriate code from the “Using the Remote” section.
Follow the on-screen instructions until the Set VCR Type feature is properly set.
Chapter 4 57
Using On-Screen Menus
Output Channel
This feature allows you to change the channel to which the satellite receiver broadcasts its signal. The default setting is channel 3.
Note: If you used A/V cables to connect your digital satellite receiver to your
TV, then you must use the TV’s video line input to see the satellite broadcast.
Remote Setup
This allows you to choose which remote control button will control the digital satellite receiver. You can choose between SAT and AUX buttons. The default is
SAT.
Use the remote control’s arrow and OK buttons to make your choice.
RF Remote Setup
This feature allows you to configure the RF remote control’s privacy code. This is the best way to avoid interference between your satellite receiver’s remote control and other Thomson RF remote controls. This is helpful if you are using two satellite receivers, each with RF remote controls.
Use the remote control’s arrow and OK buttons to make your choice. Follow the on-screen instructions for details.
Picture Size
Selecting Picture Size allows you to select the type of TV connected to the receiver. You can choose between Normal (4X3) or Cinema (16X9). The default is Normal.
Dolby Digital
This menu feature allows the system’s audio output to use Dolby-Digital quality sound. You must have the digital satellite receiver attached to a Dolby-Digital enabled receiver or decoder via the DIGITAL AUDIO output jacks on back of the satellite receiver in order for this feature to work.
58 Chapter 4
Using On-Screen Menus
Dolby Digital* Setup
Dolby Digital (when available) provides six independent soundtrack channels through a digital audio output jack. Your digital satellite receiver has an SPDIF [IEC-958] digital PCM or Dolby Digital-encoded digital audio output jack. This can be connected to an external Digital Audio Receiver/Decoder equipped with a compatible digital audio input (see page 14 in the Setup and Connections section for more information). With such additional equipment, you can enjoy more dynamic and realistic sound.
Digital Satellite Receiver
DIGITAL
AUDIO
OUTPUT
OPTICAL (SPDIF)
DIGITAL AUDIO
CABLE Digital A/V Receiver
DIGITAL
AUDIO
INPUT
CENTER
R
FRONT
FRONT
SPEAKER
(LEFT)
SUB
WOOFER
REAR
SPEAKER
(RIGHT)
REAR
SPEAKER
(LEFT)
Requirements
• Digital Audio Receiver/Decoder with a digital optical input jack.
• Programming with a digital soundtrack.
• Optical (SPDIF) cable.
• Six speakers: left front, left rear (surround), right front, right rear (surround), center and sub-woofer.
Connections
This diagram illustrates the equipment connections and home theatre speaker arrangements. Check your equipment’s user’s manual for more detailed connection information. (Note: older digital equipment may not be compatible with the Dolby Digital bitstream and could cause damage to ears, headphones, or speakers. Please read the note below for more information.)
Note: This digital satellite receiver’s digital audio output jack fully complies with the international standard governing this type of jack (IEC958), and is designed for connection to a Dolby Digital (AC-3 or
PCM) receiver or Dolby Digital (AC-3 or PCM) decoder. Older equipment, some of which is not fully compliant with IEC958, may not be compatible with the Dolby Digital bitstream. Such a connection using anything other than a PCM, Dolby Digital, or Dolby Pro Logic receiver or decoder could create a high noise level, causing damage to headphones or speakers.
Chapter 4 59
Using On-Screen Menus
Time Zone
Using this feature allows you to set the local time zone and to enact a Daylight-
Saving time option. Accurate time is necessary for Timer Recordings and Watch and Remind features, but setting the time zone is normally automatic, and generally does not require you to do anything.
Setting the time zone should only be done in rare circumstances, such as if the program times are wrong after the system card has been activated.
Note: You must select an entry in the Choose your time zone field before all menu items are displayed.
Tip
It is important to select the correct dish type. If you do not, you will not receive the proper dish pointing coordinates and you will not be able to take full advantage of your
DIRECTV System.
Multi-Switch Setup
This feature allows the satellite system to know if you have a multi-switch connected to the system and to determine what type of multi-switch is used.
This feature should only be used in rare circumstances, such as when instructed to do so by DIRECTV.
Dish Pointing
The Dish Pointing menu helps you set up your digital satellite receiver and optimize your reception of the satellite signal.
Selecting Dish Antenna
It is important to complete each of the following steps required for your satellite dish antenna. If you do not, you will not receive proper dish pointing coordinates and will not be able to take full advantage of your digital satellite receiver.
Specify the type of dish you are using:
1. Press MENU on the remote control to bring up the Main menu.
2. Select System Setup, then Dish Pointing, then press OK to access the dish pointing screen.
3. Select Dish is highlighted by default. Press the OK or right arrow button to access the information on the right-side panel.
4. Specify the type of dish you are using: a round satellite dish or an oval satellite dish with two or three LNBs (Low Noise Block-converter). When the proper dish is highlighted, press OK.
Note: Changing the dish type will delete all stored Guide information while the digital satellite receiver gets the updated Guide data. While updating
Guide information, advanced search features such as the Scout™ and
AlphaSort™ will only have a few hours of data from which to work.
60 Chapter 4
LNBs
Using On-Screen Menus
Enter Zip Code
This feature allows you to find dish-pointing coordinates from your local zip code.
1. In the Dish Pointing menu, use the remote control’s arrow buttons to select
Enter Zip Code.
2. Use the numeric buttons on the remote control to enter in the proper zip code.
3. After entering the final digit, the receiver displays the dish-pointing coordinates. For convenience, record the numbers in the spaces below.
Note: If you have a round satellite antenna, you will not see numbers for
Tilt. Tilt applies only for satellite antennas with more than one LNB.
An oval satellite dish with two LNBs
(not provided with all systems).
Tip
Azimuth is the side- to-side direction that the satellite dish antenna is pointed.
Elevation is the up/down angle that the satellite dish antenna is pointed. Tilt is the circular rotation of the dish itself, like the motion of a steering wheel.
Dish-pointing Coordinates
Elevation ____________ Azimuth ____________
Tilt (oval satellite dish only) _____________________
Select by City
Allows you to choose major cities from selected states to find dish-pointing coordinates.
Enter Lat/Long
Allows you to find dish-pointing coordinates from latitude and longitude entries. Latitudes between 20 and 55 can be entered, and longitudes between
65 and 125 can be entered.
Signal Meter
This feature allows you to determine the strength of all available signals, one at a time. There is a separate test for each satellite from which your antenna receives information.
Chapter 4 61
Using On-Screen Menus
Tip
If your system fails a test, run the system test several times before concluding that there is a problem.
Occasional fluctuations in the phone line or satellite signal can give temporary false readings.
The “RSA Secure” logo ensures that only authorized upgrades or modifications are delivered to your digital satellite receiver.
System Test
This function allows you to perform a system-level diagnostic test on the satellite receiver. There are four sub-tests within this system test. Each one will display results after the testing for that area is complete. The receiver’s access card number is also displayed in this menu.
Note: While the system is testing the signal, the video will temporarily blank out. When the tests are complete, a summary display appears.
System Info
This function displays the model and serial numbers of the receiver. It will also display the brand name and display a features list.
Upgrades
Your digital satellite receiver is able to receive upgrades or modifications to some of its features and functions. These modifications will occur automatically, usually at times when your receiver would likely be turned off. If your receiver is on when an upgrade or modification is sent, you may experience a disruption in reception for a minute or two. Your reception should return to normal after the modification is complete.
Note: Your receiver must be plugged in to receive any updates. Do not unplug your receiver while an update is in progress. Please consult the
Upgrades Menu to find a schedule of upgrades or modifications planned by
DIRECTV.
New Access Card
Selecting the New Access Card function allows you to update the digital satellite receiver with a new access card. This is necessary on occasion when DIRECTV sends out a new card.
Alternate Data
Selects from among the available data channels.
Interactive
This function allows you to learn more about DIRECTV INTERACTIVE™. It also allows you to setup an account for the free service, review transactions and messages, and to change settings.
*RSATM Secure and the RSATM Secure logo are trademarks of RSA Data Security, Inc.
62 Chapter 4
Other
Information
Chapter Overview:
• Troubleshooting
• Finding the TV’s Video Line Input
• Running the System Test
• Limited Warranty
• Accessory Order Form
• Index
Changing Entertainment. Again.
Graphics contained within this publication are for representation only
Chapter 5
63
63
Other Information
Troubleshooting
Many problems can be corrected by performing a simple reset of the digital satellite receiver. If you experience the following:
• Image freezes
• Blank screen
• Audio freezes
• Won’t respond to front panel or remote try this: press and hold the INFO and right arrow buttons for at least three seconds. If the problems persist, try unplugging the digital satellite receiver for 15 seconds to 2 minutes and then plug it in again.
Running the System Test (later in this section) can also help you diagnose and solve many common problems.
Digital Satellite Receiver Problems
Wrong picture
The digital satellite receiver and most VCRs let you toggle between signals. If you don’t see the signal you think you should be seeing, try using these buttons to toggle between the signals:
• Press the TV/VCR button on the VCR remote or on the VCR’s front panel.
• Press the ANTENNA button on the remote control.
Taking either of the above actions lets you switch the source of the video signal from satellite signals to the off-air antenna or cable signal, and vice versa.
• You may not have installed your satellite dish antenna properly.
Refer to the dish pointing instructions in the Menu section of this book and the installation guide that came with your satellite dish antenna.
Problems with Caller ID
• Most wireless phone jacks will function properly with Caller ID. However to verify proper
Caller ID operation, directly connect the phone line to a standard wall-mount phone jack.
Light flashes on front panel
• You have unread Caller ID messages. Highlight and select Messages from the Main menu, and then select Caller ID List to see a list of sequential Caller ID information. Once you access your messages, the L.E.D. flashing will stop.
Receiver will not turn on
• Check to make sure it is plugged in.
• Check the wall receptacle (or extension cord) to make sure it is “live” by plugging in something else.
• Maybe batteries in remote control are “dead.”
• Maybe remote control is not aimed at remote sensor.
• Unplug the receiver. Wait five minutes. Plug it in again.
Turns off while playing
• Electronic protection circuit may have been activated because of a power surge. Wait 30 seconds and then turn on again. If this happens frequently, the voltage in your house may be abnormally high or low.
64 Chapter 5
Other Information
Satellite receiver turns on or changes channels unexpectedly
• Scheduled Watch or Record timer has been activated.
Blank screen
• Your satellite receiver may be hooked incorrectly to the TV. Change channels using the satellite receiver’s front panel buttons to see if the channel banner appears. If it does not, check the Setup and Connections section for instructions about connecting your satellite receiver.
Partial programming loss
• Your multiple LNB satellite antenna may be incorrectly configured. Change the dish type set in your receiver’s preferences. Press the MENU button on the remote control, then select System
Setup. In the next menus, select Dish Pointing, and then Select Dish. From the Select Dish display, make sure the proper antenna is selected (round, or oval with 2 LNBs, or oval with 3
LNBs.
Remote Control Problems
Problems with the remote control
• Maybe something is between the remote control and the remote sensor.
• Maybe the remote control is not in SAT mode. Press the SAT (or, if your remote is older,
SAT1 or DIRECTV) button so the remote will control the digital satellite receiver.
• Remember to press the OK button after entering a channel number that is less than four digits long.
• Maybe batteries in the remote control are weak, dead or installed incorrectly. Try replacing batteries. (Note that when you replace the batteries you may have to reprogram your remote to control other devices.)
• Remove batteries; press and hold the 1 button for at least 60 seconds to drain the microprocessor inside the remote control. Release number 1, replace the batteries, and (if necessary) reprogram the remote.
• If you are trying to operate a device other than the digital satellite receiver that you have programmed the remote to control, make sure you press the corresponding device button
(DVD, VCR2, etc.) first.
TV or VCR Problems
Blank screen
• Maybe the component connected to the input jacks is not turned on.
• Try another channel.
TV turns on or changes channels unexpectedly
• A scheduled Watch or Record Timer has been activated.
VCR turns on or off unexpectedly
• A timer may be set to record. The timer will automatically turn the VCR on and off.
Chapter 5 65
Other Information
WHO•
INPUT
Button
TV
Button
VCR1
ON • OFF
TV
DVD VCR2 AUX SAT
MUTE
CH +
SKIP
V
FETCH
GUIDE
CH -
GO BACK
INFO
OK
1
MENU
2 3
CLEAR
4 5 6
7
8
WHO•INPUT
0
REVERSE PLAY
9
ANTENNA
FORWARD
RECORD STOP PAUSE
Finding the TV’s Video Input
Channel
Note: If your TV is connected with just coaxial cables, you only need to tune to channel 3 or 4.
If you used audio/video cables to connect your TV to the digital satellite receiver, you must tune your TV to the video input channel to view DIRECTV ® programming and menus. There are just as many ways to access a TV’s video input channel as there are brands and models of TVs. Below are some things you can try.
• If your TV brand is RCA, GE, or PROSCAN, press TV on the remote control that came with your digital satellite receiver. Then press the WHO•INPUT button on the remote.
• If your TV brand is not RCA, GE, or PROSCAN, consult your TV Owner’s
Manual.
If you cannot find your TV Owner’s Manual, you will have to investigate. You might access the TV’s video input channel by:
• pressing a button on the remote control
• finding it through the TV’s menu system
• tuning directly to it by pressing a specific channel number
• going through all channels in the list by pressing the channel up or down buttons on the TV.
The box below lists of some of the different ways manufacturers label the video input channel.
Video Line Input Variations
Button/switch on the TV
VIDEO
SIGNAL
VID 1
VID 2
S-VID
S-VIDEO
Button on the
TV Remote
VID 1
LINE
VID
VIDEO
S-VID
INPUT
SOURCE
AUX
Channel #
00
90
91
92
VID 1
VID 2
66 Chapter 5
Other Information
Running the System Test
The System Test allows you to run a basic diagnostics check on your digital satellite receiver. If you are experiencing any trouble with your receiver, run the system test. It will also allow you to get your access card number or to initiate diagnostic procedures on your digital satellite receiver.
First make sure that:
• all connections—jacks, cables, etc.—are correctly in place. See Chapter One, Setup and
Connections, for more information.
• There are batteries in the remote control, and they are working correctly.
• The access card is installed in the digital satellite receiver.
Follow these steps to run the diagnostics system test on your digital satellite receiver.
1. Turn on your TV and the digital satellite receiver.
2. Press the SAT button to put the remote control in satellite receiver-controlling mode, then press
MENU to bring up the Main menu.
3. Select System Setup.
5. Select System Test.
6. If your system does not pass the system test, check any of these potential trouble areas: cabling, pointing the satellite dish, phone connection, and access card.
7. If you continue to have problems, call RCA Customer Service at 1-800-679-4776.
You should run a system test several times before concluding that there is a problem. Occasional fluctuations in the phone line or satellite signal can give temporary false readings.
Fine-Tuning the Signal
If you self-installed your satellite dish antenna, you may have already used the Assisted Setup to find the dish-pointing coordinates, acquire and fine-tune the signal, and run a system test.
If you need to run the Assisted Setup again, select System Setup from the Main menu, then select
Assisted Setup.
If you just want to check your dish-pointing coordinates or run the signal strength meter, select
System Setup from the Main menu, then select Dish Pointing.
Chapter 5 67
Other Information
Limited Warranty
What your warranty covers:
• Defects in materials or workmanship.
For how long after your purchase:
• 90 days from date of purchase - Unit exchange, which includes parts and labor.
• 91 days to 1 year from date of purchase - Unit exchange, which includes parts only; you pay the labor.
• The warranty for rental units begins with the first rental or 45 days from date of shipment to the rental firm, whichever comes first.
What we will do:
•
During the initial 90 days:
Exchange the defective receiver with a new or, at our option, refurbished unit.
•
After the 90 days and within one year:
Exchange the defective receiver with a new or, at our option, refurbished unit. We will charge you a flat exchange cost to replace a defective receiver. This charge covers the labor cost for its repair.
How you get service:
• Call 1-800-679-4776 and have your unit’s date of purchase and model/serial number ready. The model/serial number information is on the back of your receiver.
• A representative will troubleshoot your problem over the phone.
• If the representative determines that you should receive a replacement receiver you will be provided with a Service
Request (SR) number and the location of a nearby exchange point if one exists. No returns will be accepted without the
SR number.
• Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the product is within the warranty period must be presented to obtain warranty service. For rental firms, proof of first rental is also required.
Option I:
1. Provide your Discover, MasterCard or Visa account number and expiration date to your phone representative. This is for security purposes only and your account will not be charged at this time.
2. We will send you a replacement unit.
3. If you return the unit to us within 14 days from the date you were provided a SR number, only items not covered by warranty will be charged to your account. If your unit is not received within 14 days, the suggested retail value of the receiver will be charged to your credit card. This amount will be credited, less a $10 handling fee, if the unit is subsequently received.
4. Ship your defective unit back to us using the replacement unit’s carton. Shipping instructions will be included on the carton along with your SR number which will allow you to easily ship the unit back to us. Make sure you insure your shipment in case of damage or loss. Include with the shipment:
• Evidence of purchase date such as a bill of sale.
• A brief note describing your receiver problem.
• Your name, address and phone number.
Option II:
1. For a fee of $10.00, we will send a replacement unit to our exchange point.
2. The exchange location will notify you of its arrival.
3. Take your unit and evidence of purchase date, such as a bill of sale, to the exchange location and you will be provided the new or refurbished unit. Please retain all accessories such as the remote control hand unit and access card.
4. If the repairs are covered by your warranty, you will not be billed.
Thomson assumes no responsibility for warranty shipments from the customer to the factory if not shipped in the manner prescribed by Thomson.
68 Chapter 5
Other Information
To receive a replacement receiver after we have received your unit:
• Write the SR number on the outside of the carton used to return the unit. Make sure you insure your shipment in case of damage or loss.
• Carefully pack the unit using the original box and packing material if possible. Please retain all accessories that were included with your unit such as the remote control hand unit and access card.
• Include with the shipment:
1.
Evidence of purchase date such as a bill of sale.
2.
A brief note describing your receiver problem.
3.
Your name, address and phone number.
• The representative will advise the address to mail a cashier’s check or money order for payment if there are any out of warranty labor or parts charges, and you elect not to use your credit card.
• After we receive your product, a new or refurbished unit will be shipped to you.
What your warranty does not cover:
• Customer instruction. (Your Owner’s Manual describes how to install, adjust, and operate your unit. Any additional information should be obtained from your dealer.)
• Acts of nature, such as but not limited to lightning damage.
• Adjustment of customer controls.
• Damage from misuse or neglect.
• A unit that has been modified or incorporated into other products or is used for institutional or other commercial purposes.
• Batteries.
• Units purchased, serviced or operated outside the continental U.S.A. and Alaska.
• Loss of programming.
• Installation.
• Shipping damage if the unit was not packed and shipped in the manner prescribed by Thomson.
• Storage fees may be charged by the exchange point if you fail to pick up the replacement unit in a timely manner.
Product Registration:
• Please complete and mail the Product Registration Card packed with your unit. It will make it easier to contact you should it ever be necessary. The return of the card is not required for warranty coverage.
Limitation of Warranty:
• THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PRODUCT. ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE) ARE HEREBY DISCLAIMED. NO VERBAL OR WRITTEN INFORMATION GIVEN BY
THOMSON MULTIMEDIA INC., ITS AGENTS OR EMPLOYEES SHALL CREATE A GUARANTY OR IN ANY WAY
INCREASE THE SCOPE OF THIS WARRANTY.
• REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE
CONSUMER. THOMSON MULTIMEDIA INC. SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF ANY EXPRESS
OR IMPLIED WARRANTY ON THIS PRODUCT. THIS DISCLAIMER OF WARRANTIES AND LIMITED WARRANTY ARE
GOVERNED BY THE LAWS OF THE STATE OF INDIANA. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE
LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS
PRODUCT IS LIMITED TO THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.
How state law relates to warranty:
• Some states do not allow the exclusion nor limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you.
• This warranty gives you specific legal rights, and you also may have other rights that vary from state to state.
If you purchased your product outside the United States:
• This warranty does not apply. See your dealer for warranty information.
Chapter 5 69
Other Information
FCC Registration Information
Your digital satellite receiver is registered with the Federal Communications Commission and is in compliance with parts 15B and 68, FCC Rules and Regulations.
1. Notification to the Local Telephone Company.
On the back of this equipment is a label indicating among other information, the FCC Registration number and Ringer
Equivalence Number (REN) for the equipment. You must, upon request, provide this information to your telephone company.
The REN is useful to determine the number of devices you may connect to your telephone line and still have all these devices ring when your telephone number is called. In most (but not all) areas, the sum of the RENs of all devices connected to one line should not exceed 5. To be certain of the number of devices you may connect to your line as determined by the REN, you should contact your local telephone company.
Note: This equipment may not be used on coin service provided by the telephone company. Party lines are subject to state tariffs, and therefore you may not be able to use your own telephone equipment if you are on a party line. Check with your local telephone company. Notice must be given to the telephone company upon permanent disconnection of your equipment from your line.
2. Rights of the Telephone Company.
Should your equipment cause trouble on your line which may harm the telephone network, the telephone company shall, where practicable, notify you that temporary discontinuance of service may be required. Where prior notice is not practicable and the circumstances warrant such action, the telephone company may temporarily discontinue service immediately. In case of such temporary discontinuance, the telephone company must: (1) promptly notify you of such temporary discontinuance (2) afford you the opportunity to correct the situation and (3) inform you of your right to bring a complaint to the Commission pursuant to procedures set forth in Subpart E of Part 68, FCC Rules and Regulations.
The telephone company may make changes in its communications facilities, equipment, operations of procedures where such action is required in the operation of its business and not inconsistent with FCC Rules and Regulations. If these changes are expected to affect the use or performance of your telephone equipment, the telephone company must give you adequate notice, in writing, to allow you to maintain uninterrupted service.
Radio Interference
This equipment has been type tested and found to comply with the limits for a Class B Digital Device in accordance with the specifications in Part 15 of FCC Rules. These rules are designed to provide reasonable protection against radio and television interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause interference to radio or television reception (which you can determine by turning the equipment off and on), try to correct the interference by one or more of the following measures.
• Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is “receiving” the interference).
• Change the position of the satellite receiver with respect to the radio or television equipment that is receiving interference.
• Move the satellite receiver away from equipment receiving interference.
• Plug the satellite receiver into a different wall outlet so the receiver and equipment receiving interference are on different branch circuits.
If these measures do not eliminate interference, please consult your dealer or an experienced radio/television technician for additional suggestions. Also, the Federal Communications Commission has prepared a helpful booklet, “How To Identify and Resolve Radio/TV Interference Problems”. This booklet is available from the U.S. Government Printing Office,
Washington, D.C. 20402. Please specify stock number 004-000-00345-4 when ordering copies.
70 Chapter 5
RG-6 Coaxial Burial
Cable with weatherproof “F” connectors comes in a variety of lengths.
S-Video Cable comes in
12 foot lengths.
Other Information
Accessory Order Form
Part No.
Description
RG-6 Coaxial Cable
12 feet
25 feet
50 feet
S-Video Cable 12 feet
Weatherproof “F” Connector (2)
Optical/SPDIF Cable (3-ft)
Optical/SPDIF Cable (6-ft)
TVRO Bullet Amplifier
Self-Installer’s Kit
Remote Control CRK76SG3
Surge Protector
Wireless Modem Jack
Price
DT12C
DT25C
DT50C
DT12S
D905
DV3
DV6
D903
DKIT96
247047
$69.95
$33.10
SCTV1650 $49.95
RC930 $99.95
$14.95
$24.95
$39.95
$19.95
$5.95
$15.95
$19.95
$22.95
Qty Total
Self-Installer’s Kit contains all the cable and hardware needed to install the dish and connect the system.
VCR
ON • OFF
TV
DVD VCR2 AUX DIRECTV
MUTE
CH +
SKIP
FETCH
GUIDE
CH -
GO BACK
INFO
OK
1
4
MENU
2
5
3
6
CLEAR
7
WHO•INPUT
0
REVERSE
8
PLAY
9
ANTENNA
FORWARD
RECORD STOP PAUSE
Remote Control replaces a lost remote.
Or, order a second remote for convenience.
Chapter 5
RESET
OFF
Eight outlet surge protection for cable TV, satellite systems and other electronics.
Comes with a $50,000 equipment guarantee.
Total Merchandise ............................................................
Sales Tax ............................................................................
We are required by law to collect the appropriate sales tax for each individual state, country, and locality to which the merchandise is being sent.
Shipping, Handling, and Insurance .................................
Total Amount Enclosed ....................................................
Use VISA, MasterCard, or Discover preferably.
Money order or check must be in U.S. currency only.
No COD or CASH.
$
$
$ 5.00
$
All accessories are subject to availability.
Prices are subject to change without notice.
Please complete other side also
71
Other Information
Charge your order on your VISA,
MasterCard, or Discover Card by filling in below
USE YOUR CREDIT CARD
IMPORTANT: Copy complete account number from your VISA card
®
My card expires:
IMPORTANT: Copy complete account number from your MasterCard s r r
TM
Placing an Order
To place your order by phone, have your Visa, MasterCard or
Discover Card ready and call the toll-free number listed below.
Use this number only to place on order for accessory items listed on this order form.
1-800-338-0376
To place your order by mail, detach and mail the completed order form with credit card information, money order or check in US currency (made payable to Thomson multimedia, Inc.) to the following address:
Video Accessories
PO Box 8419
Ronks, PA 17573
Copy Number above your name on
MasterCard
My card expires:
IMPORTANT: Copy complete account number from your Discover Card
My card expires:
AUTHORIZED SIGNATURE
(Credit card order will not be processed without signature)
Prices are subject to change without notice.
Print or type your name and address clearly.
A complete and correct order will save you days of waiting.
Name:
Street:
Apt:
City:
State:
Daytime Phone Number:
Zip:
Please make sure that both sides of this form have been filled out completely.
• Allow 4 weeks for delivery.
• All accessories are subject to availability.
• Prices are subject to change.
72 Chapter 5
Other Information
Glossary
Automatic Code Search
A method to program the remote control by using a series of preset codes. Programming the remote control is necessary to operate other components.
Channel Banner
A transparent banner at the top of the picture allows direct access to the key features of your digital satellite receiver including viewing suggestions, The Guardian™ channel locking system, on-screen message display, and the Scout™ keyword/phrase and the AlphaSort™ alphabetical search features. Press the INFO button on the remote control while watching normal programming to display the Channel Banner. Highlight and select the desired icon using the remote control’s arrow and OK buttons.
Direct Entry
A method to program the remote control by using codes from a list provided in the instruction manual. Programming the remote control is necessary to operate other components.
Interactive TV
A service that lets you use the satellite receivers remote control to access up-to-the-minute news, sports, financial information, weather, program trivia, free offers, and shopping– all while you watch TV.
Program Guides
A list of available programming shown on-screen when you press the remote control’s GUIDE button. Program guides display information that is contained in broadcaster signals. Your digital satellite receiver can display several types of program guides including an Advanced Program
Guide™ which stores up to three days of programming information and an information guide which lists five different channels of programming at a glance.
RSA Software Upgrades via Satellite
The digital satellite receiver is able to modify some of its features and functions with downloaded RSA-secure upgrades or modifications. RSA-secure downloads ensure that only authorized upgrades are delivered to your RCA digital satellite receiver.
Universal Remote Control
Description: A remote control that provides complete satellite system operation, and primary
function control of most brands of remote-controllable TVs, VCRs, and cable boxes.
Chapter 5 73
Index
A
Access card
B
C
Cable Box
Caller ID
Channel lists 50 add channels 50 delete channels 50
Code list
Codes
D
E
Exiting
F
G
I
I icon. See DIRECTV
INTERACTIVE
K
L
Locking
a profile 52 the system 51, 52
M
Menus
O
P
Profiles
rating limit 51 spending limits 51 viewing hours 51
Program guides
Programming
Purchases
R
Remote control
S
Satellite Receiver
Sorting by
System
T
74 Chapter 5
U
Unlocking
V
VCR
W
Wink. See DIRECTV
INTERACTIVE
Index
Chapter 5 75
This page left intentionally blank
This page left intentionally blank
If your digital satellite receiver needs service, please contact your dealer or the nearest Service Center from the Yellow
Pages. Please do not send any products to the Indianapolis address listed in this manual or on the carton. This will only add delays in service for your product.
Thomson multimedia Inc.
10330 North Meridian Street
Indianapolis, IN 46290
©2001 Thomson multimedia Inc.
Trademark(s)® Registered
Marca(s) Registrada(s)
DIRECTV, and the Cyclone Desiign logo are trademarks of
DIRECTV, Inc., a unit of Hughes Electronics Corp., and is used with permission.
Printed in the USA
TOCOM 15660900
The software used to display images in this product is based in part on the work of the
Independent JPEG Group.
THOMSON
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project