U.motion Client Touch 15 U.motion Client Touch 10

Add to my manuals
4 Pages

advertisement

U.motion Client Touch 15 U.motion Client Touch 10 | Manualzz

U.motion Client Touch 15

U.motion Client Touch 10

Schnelleinstieg

Quick Start Guide

MEG6260-0315 MEG6260-0310

it nl es pt fr de en sv no fi da hu tr kk zh ro pl el ru

en

U.motion Client Touch 10/Touch 15MEG6260-03xx© Schneider-Electric 2014enQuick Start Guide

U.motion Client Touch 10

U.motion Client Touch 15

Quick Start Guide

Installation and connection

Install the U.motion Client Touch 10 / Touch 15 (referred to as Client

Touch in the following) with the appropriate flush-mounted socket or cavity wall set.

Establish the following connections to the Client Touch:

1 Connect the protective earthing conductor to the housing (only

Client Touch 15)

– Connection via the yellow terminal.

2 Power supply AC 100-240 V, power consumption max. 20 W (Client Touch 10) or 25 W (Client Touch 15)

– As marked on the device.

3 Network

– Connection with the RJ 45 cable (included in delivery).

Setting up network connection

The network address of the Client Touch is set to the following value on delivery: 192.168.0.130

Proceed as follows for initial start-up or if no networks are working:

1 Connect the Client Touch directly with your PC via a cross-over network cable.

2 Open the network settings on your PC.

3 Open the Properties of the TCP/IP protocol (version 4) of the network port being used and set the following values:

IP address:

Subnet mask:

192.168.0.101

255.255.255.0

4 Save the settings.

5 If necessary, restart your PC.

Starting up U.motion Client Touch

Opening the administrator level

Once you have entered the network settings, open the administrator level of the Client Touch. You can perform the following Client Touch settings using the administrator level:

• Setting the language of the administrator level

• Adjusting the network parameters

• Updating software

• Resetting Client Touch to default

• Setting the time, date and time zone

• Configuring the screen saver, screen shut-down and energy saving mode

• Changing password

• Calibrating touch sensor

| You will achieve maximum functionality with the browsers Goog-

le Chrome or Apple Safari.

1 Open a browser and enter http://192.168.0.130 in the address bar.

– The log-in window will appear.

2 Log in.

User name:

Password: admin admin

– The administrator level will open.

3

Adjusting Client Touch settings for initial start-up

| Temporarily save each setting using the green service button.

Once you have entered all settings, save the data permanently using the red service button.

1 Set the desired language for the administrator level.

– Note: the language of the visualisation can be set on the U.motion KNX Server.

2 Change the network parameters:

– IP address of the U.motion KNX Server

– IP address of the Client Touch

– Subnet mask

– IP address of the router

– DNS addresses (if available)

3 Set the time, date and the time zone.

4 Now save the settings permanently by pressing the red service button.

Restarting Client Touch and calling up the visualisation

1 Log out (=> Logout).

2 Push the reset button A.

When the next screen loads you have the possibility of calling up either the visualisation or the Client Touch administrator level.

• To call up the visualisation: ignore the screen.

• To call up the administrator level: press Cancel.

|

|

You can only call up the visualisation if you have entered an IP address for the server in the administrator level. If that is not the case, the Client Touch administrator level will be loaded automatically after every restart.

More information can be found in the user manual.

en

A

– Client Touch will restart.

Schneider Schneider Electric GmbH c/o Merten

Gothaer Straße 29, 40880 Ratingen www.merten.com

www.merten-austria.at

Customer care centre:

Phone: +49 2102 - 404 6000

4

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement