Clever Acoustics MA 240Z5 User manual
Add to my manuals13 Pages
Clever Acoustics MA 240Z5 is a 240W 5-zone mixer amplifier designed for use in permanent audio installations where reliability and premium sound quality are essential. Its highly rugged construction and high-efficiency design make it perfect for continuous duty applications.
The MA 240Z5 features 5 x 50W outputs, each with separate 5-step volume controls, providing a total output of 240W. It is equipped with four XLR microphone inputs with phantom power and gain control, two dual RCA line inputs, a MIC 1 input with selectable priority over other inputs, a built-in chime with 2/4 tone selector, a phono line output, and an EMC input for emergency alarm. Additionally, it has a telephone input with separate volume control, and a remote mic input for use with the optional PM 100 paging microphone.
advertisement
www.cleveracoustics.co.uk
MA 240Z5 100V 240W 5 Zone
Mixer Amplifier
Order code: CRAM10
USER MANUAL
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE YOUR INITIAL START-UP!
CAUTION!
Keep this equipment away from rain,
moisture and liquids.
SAFETY INSTRUCTIONS
Every person involved with the installation, operation & maintenance of this equipment should:
-
-
Be competent
Follow the instructions of this manual
CAUTION! TAKE CARE USING THIS EQUIPMENT!
HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!
Before your initial start-up, please make sure that there is no damage caused during transportation. Should there be any, consult your dealer and do not use the equipment.
To maintain the equipment in good working condition and to ensure safe operation, it is necessary for the user to follow the safety instructions and warning notes written in this manual.
Please note that damages caused by user modifications to this equipment are not subject to warranty.
1
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual or any unauthorised modification to the equipment.
• Never let the power-cable come into contact with other cables. Handle the
power-cable and all mains voltage connections with particular caution!
• Never remove warning or informative labels from the equipment.
• Do not open the equipment and do not modify the equipment.
• Do not switch the equipment on and off in short intervals, as this will reduce the
system’s life.
• Only use the equipment indoors.
• Do not expose to flammable sources, liquids or gases.
• Do not carry the unit with only one handle. Always carry using both handles.
• Always disconnect the power from the mains when equipment is not in use or
before cleaning! Only handle the power-cable by the plug. Never pull out the plug
by pulling the power-cable.
• Make sure that the available voltage is between 220V-240V.
• Make sure that the power-cable is never crimped or damaged. Check the
equipment and the power-cable periodically.
• If the equipment is dropped or damaged, disconnect the mains power supply
immediately.
Have a qualified engineer inspect the equipment before operating again.
• If the equipment has been exposed to drastic temperature fluctuation (e.g. after
transportation), do not switch it on immediately. The arising condensation might
damage the equipment. Leave the equipment switched off until it has reached
room temperature.
• If your product fails to function correctly, discontinue use immediately. Pack the
unit securely (preferably in the original packing material), and return it to your
Prolight dealer for service.
• Only use fuses of same type and rating.
• Repairs, servicing and power connection must only be carried out by a qualified
technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.
• WARRANTY; One year from date of purchase.
• If this equipment is operated in any other way, than those described in this
manual, the product may suffer damage and the warranty becomes void.
• Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks.
• Do not endanger your own safety and the safety of others!
Incorrect installation or use can cause serious damage to people and property.
2
This 100V line mixer amplifier was designed specifically for use in permanent audio installations, where reliability and premium sound quality are a must. Highly rugged construction and high efficiency design make this amplifier perfect for continuous duty applications in situations were power will be left on for indefinite periods of time.
This 100V line amplifier is warranted from defects for one year from the date of purchase.
Should your amplifier require service, either within or beyond that warranty period, please contact your Prolight Dealer.
This unit includes a host of features, along with an impressive list of specifications, which are detailed over the next pages. Please take the time to read this document completely prior to installation of this product.
The Mixer Amplifier series is equipped with priority function. They are designed to suit all PA system application in schools, offices and stores.
Features
• 5 Zone Mixer amplifier for paging and background music system.
• 5 x 50W outputs each with separate 5-step volume controls (total 240W)
• Rated power: 240W
• Rack mountable chassis
• 70V, 100V and low impedance 4-8Ω loudspeaker output
• Four XLR microphone inputs with phantom power and gain control
• 2 dual RCA line inputs
• MIC 1 with selectable priority over other inputs
• Built-in chime, 2/4 tone selector
• Phono line output
• EMC input for emergency alarm
• Telephone input with separate volume control
• Master, MIC 1-4, line level volume, bass and treble control
• Optional DC input for use with battery backup power sources
• Fan cooled
Note: The multi-zone facility applies to paging and level control when using the 100V zone outputs. The multi-zone facility cannot be used for low impedance, or for multi-zone audio from the line inputs.
3
Specifications
Power output:
MA 240Z5
240Wrms / 255Wpeak
(total output across all zones)
Microphone inputs:
Sensitivity:
S/N ratio:
Frequency response:
2.45mV / 5kΩ BAL / 245mV / 5kΩ
>55dB
Phantom power:
Line inputs (1 - 2 in @ 1kHz):
Sensitivity:
Tone Control (Bass: 100Hz, Treble: 100Hz):
100Hz-15kHz (±3dB)
+48V DC
250mV / 47kΩ
S/N ratio:
Frequency response:
Tel input:
Sensitivity:
S/N ratio:
± 12dB
>65dB
80Hz-15kHz
0.3V/10kΩ
>65dB
Frequency response: 100Hz-15kHz (±3dB)
Outputs:
Per amp out (MIC 1-4, LINE 1-2, TEL IN, REMOTE IN): 0dbV / 600Ω
Remote mic (PM 100):
THD:
Power consumption:
DC power supply:
Power supply:
Dimensions (H x W x D):
Weight:
Order code:
30mV / 600Ω
<0.5%
350W
24V
240V-60Hz
132 x 484 x 338mm
20.15kg
CRAM10
4
Identification:
1. Bass & Treble controls - Use to adjust the bass and treble response.
2. PROT LED - Protection indicator LED
3. Chime & siren LEDs
4. CLIP LED - This LED will flash when the output signal starts to distort
5. All call control - Press to page all zones
6. All call LED - When all call has been selected the LED will light up.
7. Zone selection LEDs - These LEDs will light up for which zone is selected
8. Zone selection buttons - Use these to select the zones
9. AC LED -This LED will light up when power is turned on and is used via the mains IEC socket
10. Power LED - This LED will light up once the amp is switched on
11. DC LED - This LED will light up when optional DC power supply is used
12. On/off power switch - Use the switch to power the unit on or off
13. Master volume control - Use this control to increase or decrease the master volume
15. Siren and chime selection buttons - Use these to select the siren and chime functions
16. Chime volume control - Use this control to increase or decrease the chime volume
17. Line & Mic volume controls - Use this control to increase or decrease the line and mic volume
18. Zone 1 - 5 Speaker outputs - Use this to connect the speakers to dedicated zones
19. Mains IEC power input socket - Use this to connect to the mains
20. Mic 1 priority selection button - When this button is selected, it will give priority to channel 1
over all other channels
21. Phantom 48V power switches - Use these switches to turn the Phantom +48V on and off for
each of the mic inputs
22. Optional DC power supply - Use this to connect to your optional DC 24V power supply
23. Combi XLR/6.35mm mono jack mic inputs sockets - Use these to connect the microphones
24. Line input sockets - Use these sockets to connect to your audio equipment
25. Line output socket - Use this socket to connect to your power amp or recording equipment
26. EMC input socket - Use this to connect to your emergency panel unit. When the EMC is
connected, the EMC has auto override over all other inputs
27. TEL input socket - Use this socket to connect to you telephone interface for paging and
announcements
5
28. TEL audio volume - Use this control to increase or decrease the telephone volume
29. Chime tone selector - Use this to select the 2 tone or 4 tone options
30. Fan vent
31. PM 100 Mic input socket - Use this to connect the PM 100 Paging mic (sold separately)
Pin configuration:
Pin 1: Remote amplifier input signal hot (+)
Pin 2: Remote amplifier input signal cold (-)
Pin 3: Signal ground
Pin 4: Remote control 1 (zone 1)
Pin 5: Remote control 2 (zone 2)
Pin 6: Remote control 3 (zone 3)
Pin 7: Remote control 4 (zone 4)
Pin 8: Remote control 5 (zone 5)
Pin 9: Remote control ground
Pin 10: DC +24V
Pin 11: Input chime
Pin 12, 13, 14, 15: Not used
32. Speaker terminals - For 100V, 70V, 4Ω, 8Ω, chime and active speakers connections
Rack Installation
The MA Series are rack mountable. The rack you use should be a double door rack where you can open the front and rear panel. When mounting the amplifier into the rack, please make sure that there is enough space around the amplifier.
Be careful when mounting the amplifier into the rack. Put the heaviest products into the lower part of the rack. Be aware that fastening the amplifier with four screws on the front panel is not enough.
Inputs
Short cables runs improve the sound quality remarkably. Input cables should be short and direct, since high frequencies will mostly be absorbed if the cables are unnecessarily long. Besides that a longer cable may lead to humming and noise problems. If the cable runs are unavoidable, you should use balanced cables.
Outputs
The high damping factor of your amplifier supplies a clear sound reproduction. Unnecessarily long and thin cables used for low impedance (4-16Ω) speakers will influence the damping factor and thus the low frequencies in a negative way. In order to safeguard good sound quality, the damping factor should lie around 50. The longer a cable has to be the thicker it should be. For longer cable runs please ensure the 100V outputs are used for 100V speakers.
Connect your speaker systems via the speaker terminals (COM = -VE)
Examples: 1) COM + 4Ω
2) COM + 8Ω
3) COM + 70V
4) COM + 100V
Note: Please do not use more than one pair of output terminals
6
Connections To The Mains
Before connecting the amplifier to the local mains voltage outlet should be checked to ensure the available supply is 240V~AC 50Hz. This product is CLASS1 and requires a protective mains earth to be connected at all times. DO NOT remove or disconnect the earth.
Power On/Off Procedure
After connecting your amplifier to the mains, turn all controls counter clockwise to the “min” position. Turn on audio sources (MP3 players, CD players, Microphones etc) before powering the amplifier ON. The last product to be switched on is the amplifier.
If you wish to power off the system, turn the amplifier’s master volume control counter clockwise to the “min” position before switching the amplifier OFF before any audio sources are switched off.
By following this procedure it will prevent acoustic shocks to the speakers or potential damage to system components.
Machine operation
1. After connecting all audio sources and powering on the mixer amplifier, adjust the level of each audio input to achieve the desired “mix”. Care should be taken to when adjusting microphone input volumes and the master volume, adjust both of these in small increment’s to avoid feedback
(howl around). The goal is to achieve a clear balance between music and voice ensuring announcements can be clearly heard.
2. Microphone input No.1 features selectable voice operated override (VOX), this will mute all other inputs. After 3 seconds of no signal to the MIC1 input the other inputs will return to their original state. The VOX level can be adjusted on the rear panel.
3. The Clever Acoustics amplifiers all feature output VU meter’s with CLIP indication. Should the
CLIP indicator illuminate (flashing) the output of the amplifier is too high, turn the master volume anti-clockwise to reduce the output.
4. The Clever Acoustics amplifiers all feature protection with LED indication. Should the
PROTECT indicator illuminate, turn the master volume control anti-clockwise fully and switch off the amplifier for 15 seconds as the amplifier may have entered PROTECT mode temporarily due to a peak signal, care should then be taken to ensure all input levels are set correctly. If the amplifier persists to enter PROTECT mode the amplifier should be switched off and left to cool for 5-10 minutes before switching back on. If the PROTECT indicator remains lit this indicates a problem with the amplifier or amplifier load (ie Short Circuit).
5. Speaker & Amplifier systems can produce high sound pressure levels, please operate all controls with caution to ensure people are not exposed to excessive or dangerous sound pressure levels.
7
Panel Connections:
MAINS
ZONE 1
COM 100V
ZONE 2
COM 100V
ZONE 3
COM 100V
ZONE 4
COM 100V
ZONE 5
COM 100V
COM 4
OUTPUT
8 Ω 70V 100V CHIME ACTIVE
REMOTE MIC
240V 50Hz
T6.3AL 250V
BATTERY SUPPLY
24V 16A
ON OFF
+48V PHANTOM
PRIORITY ON OFF
+48V PHANTOM
MIC 1 MIC 2
GAIN GAIN
ON OFF
+48V PHANTOM
MIC 3
GAIN
ON OFF
+48V PHANTOM
MIC 4
GAIN
XLR BAL
1-GND
2-HOT+
3-COLD-
INPUT
LINE 1 LINE 2
OUT
LINE
2 TONE
CHIME
4 TONE
TEL INPUT
EMC
MIC 1 MIC 2 MIC 3 MIC 4
24V DC INPUT
(Optional)
TEL INPUT
OTHER AMPLIFIER
AUDIO EQUIPMENT
EMERGENCY PANEL
TELEPHONE INTERFACE
PM 100 (CRMIC01)
8
Speaker connections:
Total impedance
160Ω
Total impedance
160Ω
TOTAL LOAD OF SPEAKERS CONNECTED
ACROSS ALL ZONES PLUS SPEAKERS
CONNECTED TO THE MAIN OUTPUTS
MUST NOT EXCEED 240W (208.3Ω)
Notes:
• Both the 4Ω, 8Ω, 70V and 100V terminals cannot be used at the same time.
• Impedances indicated in the figures represent the total speaker system (load) impedances.
Loads presented to the amplifier must be equal to or greater than listed above. Speaker
impedances must be measured using a true impedance meter, do not standard multimeters.
WARNING!
Be sure to attach the supplied terminal cover attached after connection. Because high voltage is applied to the speaker terminals, car should be taken never touch these terminals to avoid electric shock.
All speaker connections should be made using bare wire or suitable insulated crimp terminals. Please ensure no loose strands are present as these may short across terminals causing damage to the amplifier
9
Connection With The Mains
Connect the unit to the mains via the IEC mains inlet using the 13A UK - IEC cord supplied.
The earth has to be connected.
Switch the unit on. After switching on the speaker system, wait 8 - 10 seconds before you turn the volume control up in order to avoid speaker damage.
CAUTION! Increase the level of each channel up to the point where the clip LEDs illuminate.
Always check the sound pressure level with a meter in order to keep to the legal threshold.
Balanced XLR Jack Connection
10
Problem Chart
PROBLEM
No Power
No Sound
Noise
Distorted Sound
CAUSE
The power cord is not connected
The power cord of the respective product is not connected properly or not at all.
REMEDY
Check the power cord and any extension cables
Check the power cord and if the plugs are properly connected with the sockets.
The connection socket or the plug is dirty.
Clean the socket and/or the plug.
The input signal is too strong
Load impedance is to low Check load impedance vs amplifier specification, reduce as required.
CAUTION - DANGER TO LIFE
DISCONNECT FROM THE MAINS BEFORE
STARTING MAINTENANCE OPERATION and
We recommend a frequent cleaning of the product. Please use a soft lint free and moistened cloth. Never use alcohol or solvents.
There are no serviceable parts inside the product except for the fuse. Maintenance and service operations are only to be carried out by authorised dealers.
Replacing the fuse
Only replace the fuse by a fuse of the same type and rating.
Before replacing the fuse, unplug the mains lead.
Should you need any spare parts, please use genuine parts.
Should you have any further questions, please contact your dealer.
11
English
Correct Disposal of this Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with seperate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please seperate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.
www.cleveracoustics.co.uk
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project