advertisement
USER MANUAL
Auto Clean Rotisserie
Auto Clean Rotisserie + Integrated Condenser
ACR
WARNING
Read the instructions before using the machine.
EN (Original Instruction) 9123833 / 1704
ACR
KEEP THIS USER MANUAL FOR FUTURE USE
© 2017 Fri-Jado B.V., Etten-Leur, The Netherlands.
We advise you to contact your supplier for the guarantee period and conditions. Further we refer to our General Terms and Conditions for Sales and Delivery that are available upon request.
The manufacturer does not accept any liability for damage or injury caused by failing to adhere to these regulations or by not observing the usual caution or care in actions, operation, maintenance or repair activities, even if not explicitly described in this manual.
As a result of constant commitment to improvement, it may happen that your unit deviates in detail from what is described in this manual. For this reason, the given instructions are only a guideline for the installation, use, maintenance and repair of the unit referred to in this manual. This manual has been composed with the utmost care. The manufacturer shall, however, not be held responsible for any mistakes in this manual nor for any consequences thereof. The user is allowed to copy this manual for own use. Further all rights are reserved and nothing in this manual may be reproduced and/or made public in any way.
Modifications:
In case of unauthorized modifications in or on the unit, every liability on the part of the manufacturer becomes null and void.
EN 2 / 40
Empty page.
ACR
EN 3 / 40
ACR
CONTENTS
EN 4 / 40
ACR
EN 5 / 40
1. INTRODUCTION
ACR
1.1 General
This manual is intended for the user of the ACR (Auto Clean Rotisserie). The features and controls are being described, along with directions for the safest and most efficient use, in order to guarantee a long life of the unit.
All pictograms, symbols and drawings in this manual apply to the ACR.
1.2 Identification of the unit
The identification plate can be found on the outside of the machine, and contains the following data:
Name of the supplier or the manufacturer
Model
Serial number
Year of construction
Voltage
Frequency
Power consumption
1.3 Pictograms and symbols
In this manual, the following pictograms and symbols are used:
WARNING
Possible physical injury or serious damage to the unit, if the instructions are not carefully followed.
WARNING
Hazardous electrical voltage.
WARNING
Danger of getting injured by hot surfaces.
Suggestions and recommendations to simplify indicated actions.
Recycling symbol.
Direction of view symbol.
EN 6 / 40
1.4 Safety instructions
WARNING
The outside of the unit can be very hot.
WARNING
The maximum load on top of the unit may never exceed 50 kg (110 lbs).
WARNING
Always use the brakes on both front wheels:
ACR
1.4.1 General
The user of the unit will be fully responsible for abiding the locally prevailing safety- rules and regulations.
The unit may be operated by qualified and authorised persons only. Anyone working on or with this unit must be familiar with the contents of this manual and carefully follow all guidelines and instructions. Never change the order of the steps to be performed. The management must instruct the personnel on the basis of this manual and follow all instructions and regulations.
The pictograms, labels, instructions and warning signs attached to the unit, are part of the safety measures. They may never be covered or removed, and have to be clearly visible during the entire lifetime of the unit.
Immediately repair or replace damaged or illegible pictograms, warnings and instructions.
To avoid short-circuiting, never clean the unit using a water hose. For cleaning instructions,
During the grilling process, the unit can get very hot.
To protect the operator for possible hot gases the door is equipped with a two-step unlocking device.
When the door is opened the rotor stops and the heater is de-energized.
The unit must be cleaned regularly to ensure proper functioning and prevent fire hazard
(over heating). Especially the back of the fan plate.
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
EN 7 / 40
ACR
1.4.2 Moving
When moving the unit:
Before moving the unit, first switch off the mains voltage by pulling the plug from the wall socket. After that, cool-down the unit for at least ten minutes.
The units equipped with wheels are not suited to pass ledges or obstacles higher than 10 mm (3/8 inch).
When moving the unit, always push at the center of the unit. Never on top. Never at the bottom.
Make sure that the wheels can move freely, so they never touch the power lead.
1.4.3 Outdoor use restrictions
To avoid short-circuiting, the units may not be used outdoors unprotected. Placing under a screen is allowed.
EN 8 / 40
ACR
1.5 Hygiene
The quality of a fresh product always depends on hygiene. Especially grilling products. With the risk of salmonella contamination – especially for chicken products – you must make sure that grilled products can never be mixed with uncooked products. Also contact between grilled products and hands or tools that have been in contact with raw chicken meat, must be avoided at all times.
Hands or tools that have been in contact with raw chicken meat, must be cleaned thoroughly.
1.6 Service and technical support
The electrical schematics of your unit is included. In case of malfunctions you can contact your dealer/service agent. Make sure you have the following data available:
Model.
Serial number.
This data can be found on the identification plate.
1.7 Storage
If the unit will not be used temporarily, and will be stored, follow these instructions:
Clean the unit thoroughly.
Wrap the unit from getting dusty.
Store the unit in a dry, non-condensing environment.
1.8 Disposal
Dispose of the machine, any components or lubricants removed from it safely in accordance with all local and national safety and environment requirements.
EN 9 / 40
2. DESCRIPTION OF THE UNIT
ACR
2.1 Technical description
The ACR uses convection heat. The rotor is being wheeled by a maintenance-free motor with a gear box. The fan provides an equally divided heat. The glass panes are equipped with a heat reflecting layer to keep the heat inside the grill.
The plating of the unit is made of stainless steel. The product contact parts are made of stainless steel AISI 304 (eventual with PTFE coating).
The mains cable is provided with a plug (European models).
The intelligent control keeps the temperature inside the unit fixed to level set by the operator.
During the entire process, the interior of the unit will be illuminated by halogen lamps.
The intelligent control has a capability to store 250 different programs.
Each program can consist of a pre-heat step, with additional (maximum 9) steps, in which the cooking time and temperature can be set. Communication through USB enables easy read-out, re-work and creating of programs via a PC. For this, special software is available at Fri-Jado.
The unit has an automated cleaning program that cleanses the unit. An Integrated Condenser (IC) is optional available.
2.2 Intended use
The ACR has been designed for grilling meat products and has a special self-cleaning feature. Any other use will not be regarded as intended use.
The manufacturer accepts no liability whatsoever for loss or injury caused by failing to strictly adhere to the safety guidelines and instructions in this manual or due to carelessness during installation, use, maintenance and repair of the unit referred to in this manual and any of its accessories.
Use the unit in perfect technical condition only.
2.3 Accessories
Your unit contains the following standard accessories:
Meat forks.
User manual.
For optional accessories refer to section 11.
EN 10 / 40
3. INSTALLATION AND FIRST USE
ACR
WARNING
Use the hoses supplied with the machine. Never use second-hand hoses!
All packing materials used for this unit are suited for recycling.
After unpacking, check the state of the unit. In case of damage, store the packing material, and contact the transporter within fifteen working days after receiving the goods.
3.1 Unpacking the unit
Your unit is shipped using a wooden crate. All units are placed on a wooden pallet.
1. Remove the wooden crate.
2. Remove all remaining packing materials from the unit.
3. Remove the protective foil from the metal parts.
4. Take off the standard accessories.
EN 11 / 40
ACR
3.2 Installation and positioning
WARNING
Position the unit on a flat and horizontal surface. A temporally inclined plane of maximum 5° is allowed.
WARNING
The unit must be installed by a certified electrician.
2 1
R 955 mm (37.6 inch)
Positioning:
The user must have sufficient freedom of movement to properly operate the unit.
The ambient temperature of the unit must be between 10 and 30 °C (50 and 86 °F).
Use proper lifting – and transport tools to move the unit.
Place the unit, using a spirit level, flat on a solid surface. Mind the weight of the unit!
The distances between the sides and other units or walls must be at least 100 mm (4 inch).
The minimum distance between the operator-side and possible glass panes or wooden
(partition) walls must be at least 250 mm (10 inch). The same is valid for the customer-side.
The space between the unit and the surface it is put on, must be kept clear for proper ventilation of the electrical compartment.
Keep a distance of at least 500 mm (20 inch) of free space above the unit. Placing the unit under a hood is required.
In case of a wheeled unit, the floor must be flat and levelled.
The products inside the unit must be clearly visible.
Keep children away from the operating side of the unit.
EN 12 / 40
ACR
Installation:
Secure the unit to the building structure using the tether bracket, refer to the installation manual.
The unit has fixed wiring and must be connected by a certified electrician.
A water connection with an aerated valve with a ¾ inch thread connection, with a minimum continuous flow rate of 15 litres / min, must be available near the unit. The water pressure must be between 200 and 500 kPa (2 and 5 bar), preferably at least 300kPa (3 bar). Use connection
①
for filtered water and connection
②
for non-filtered water. Refer to the
Installation Manual.
Use the hoses supplied with the machine.
An open drainage with a diameter of at least 40 mm (1.6 inch) must be available near the unit.
3.3 First use
When using the unit for the first time, clean the interior thoroughly with soap suds. Run the Install program and heat up the unit as described below. After commissioning discoloration of the cooking/grilling area can occur.
➊ ` ➋
➍
➌
➎
EN 13 / 40
ACR
Metal odour
To remove both the oil- and metal odour that will appear at first use, the unit must be heated at the maximum temperature for at least half an hour.
➊ ➋
➌
SET 220°C / 428 °F
➍
SET 30-45 min.
220°C / 428 °F
START
1. Press “ON/OFF” for 3 seconds on to switch-on the unit.
2. Press OK the display the menu.
3. Create a new program containing ONE step of 220 °C (428 °F) and a duration of at
least 30 minutes (See section 7).
4. Select tab “Operate” to return to the operation field.
5.
Select the new program and press START/PAUSE to start (See section 4).
6. Allow the unit to fully execute the program.
The unit is ready for use.
EN 14 / 40
4. OPERATION AND USE
4.1 Control panel
SELECTION BUTTONS
DISPLAY SCREEN
START
PAUSE
ROTOR BUTTON
ON
OFF
OK BUTTON
Button
ROTATION PAD
(DIAL)
STOP
CANCEL
SELECTION BUTTONS
ON / OFF
START / PAUSE
STOP / CANCEL
OK BUTTON
ROTOR BUTTON
Function
Selecting tabs in display screen.
Switching the unit on and off.
Starting and ending a program.
Interrupting a program (one step back in the menu).
Acknowledge a choice.
Rotate the rotor.
ROTATION PAD See "Rotation pad".
Rotation pad
This pad is used for:
Navigating through the menu-items in the screen.
Changing the settings.
Changing the settings quickly
Increase value: rub the pad clock-wise with one finger.
Decrease value: rub the pad counter-clock-wise with one finger.
Screen
The following tabs are present:
Operate “Choose between programs”
Program
Settings
“Creating programs”
“Change settings of programs”
EN 15 / 40
ACR
4.2 Switching-on the unit
➊ ➋
ACR
4.3 Loading the unit
WARNING
To protect the operator for possible hot gases the door is equipped with a two-step unlocking device.
To open the door move the handle first clock-wise then counter-clock-wise
When the door is open press the rotor button to activate the rotor. This allow easy loading or unloading the products.
Whilst loading the unit, make sure that the rotor gets evenly loaded, so that the mass of the products is evenly spread over de rotor, causing an equal balance. Do not allow empty meat forks, meat baskets and chicken racks etc. in the grilling process.
4.3.1 Loading the unit using meat forks
The unit will be equipped with a set of meat forks.
Whole uncut chickens should always be grilled using the meat forks. This way their natural fat will baste each other, giving a perfectly slender cooking result.
Refer to the YouTube movie: “Fri-Jado instruction for binding and loading chicken”.
EN 16 / 40
For preparing chicken or any other poultry, you can work as follows.
ACR
1. Insert one point of the meat fork through the chest at the position of the wings.
Insert the other point through the drum sticks. Don‟t forget to include the wings.
2. Leave some space between the products, for an even exposure and browning.
3. Put the meat forks onto the rotor disks in such a way that during grilling the chicken breasts face the operator.
4. Put the points of the meat forks through the appropriate holes in the rotor disks.
5. The other end of the meat forks must be put through the corresponding holes in the opposite rotor disk.
6. To insert the remaining meat forks in the unit, act as follows:
Switchon the unit using the on/off button‟.
With the door opened, use the rotor button to move the rotor to easily insert the next meat fork. Keep the rotor button pressed until the rotor reaches the desired position.
Repeat these steps, until all products are loaded.
Whole uncut chickens should always be grilled using the meat forks. This way their natural fat will baste each other, giving a perfectly slender cooking result.
Refer to the You-Tube movie : “Fri-Jado instruction for binding and loading chicken”.
EN 17 / 40
ACR
4.3.2 Loading the rotisserie using V-shape spits (accessory)
If you are using V-shape spits act as follows:
Place the skewer into the small outside hole on the rotor end plate on your left (as you face the oven). The back of the V-shape spit should be pointing towards you.
Fit the other end on the spit into the small corresponding holes on the rotor end plate on your right (as you face the oven).
Make sure the spit is level. If spit is not level make sure you are using the correct holes on the rotor end plates.
4.3.3 Loading the unit using meat baskets (accessory)
If you use meat baskets, act as follows:
Place the meat baskets to the appropriate pins.
Whilst loading the unit with meat baskets, you must see to it, that the rotor gets evenly loaded, so that the mass of the products is evenly spread over de rotor, causing an equal balance.
Also see to it that no meat parts are sticking out of the baskets.
EN 18 / 40
4.3.4 Loading the rotisserie using chicken racks (accessory)
When using chicken racks, you can use the principle as described in section 4.3.3.
ACR
For preparing chicken or any other poultry in the racks, you can use Picture 1 as an example.
Picture 1
4.3.5 Loading the rotisserie using two different accessories.
WARNING
After loading the rotor, at least make ONE full rotation, and check whether the rotor can spin without obstructions.
If you want to load the unit using two different accessories at the same time, always fill the rotor with ONE accessory fewer than the maximum allowed quantity. See to it that accessories of the same type are placed consecutively.
EN 19 / 40
4.4 Grilling time
Grilling time depends on a number of factors:
The ambient temperature and draft in the direct vicinity of the unit.
Grilling temperature.
The initial product temperature.
The sort of meat (fat or lean) and with or without additives.
The mass and shape of the product.
The total amount of meat to be grilled in one grilling cycle.
The end result.
4.5 Taking out the products
WARNING
After the grilling, the interior of the unit and the glass panes are very hot.
Always use oven gloves when taking out the meat forks or other accessories
4.5.1 Taking out the meat forks
When taking out the meat forks, it is best to act as follows:
1. Hold the meat fork firmly.
2. Slightly lift the end with the grips and shift the meat fork into the direction of its points.
This releases the meat fork.
3. Take the meat fork at its other end and take it out of the unit.
4. Remove the products from the meat fork.
ACR
Refer to the YouTube movie: “Fri-Jado instruction for unloading chicken from a rotisserie”.
4.5.2 Taking out the V-shape spit (accessory)
For taking out the V-shape spit you can use the same principle as described in section 4.5.1.
4.5.3 Taking out the chicken racks (accessory).
When taking out the chicken racks from the rotisserie it is best to act as follows:
1. Slightly lift both ends of the chicken rack.
2. Move the rack towards either the left or right hand side of the unit. This action unlocks one end of the rack.
3. Move the unlocked end towards you, and take out the rack from the unit.
Depending on the number of prepared products, you may have to empty the racks before they can be removed.
EN 20 / 40
ACR
4.5.4 Taking out the meat baskets (accessories)
For taking out the meat baskets, you can use the same principal as described in section 4.5.1, but
it is recommended to act as follows:
1. Slightly lift both ends of the meat basket.
2. Move either one side towards you, and take out the basket from the unit.
Depending on the number of prepared products, you may have to empty the baskets before they can be removed.
4.6 Switching-off the unit
Press ON/OFF button and hold for approx. 3 seconds.
EN 21 / 40
5. OPERATE
5.1 Starting a program
1. Press the left-hand selection button.
2. Select the required program. The total duration of the program is shown in minutes next to the name of the program.
3. Press START/PAUSE.
ACR
EN
Use the rotation pad or arrow buttons to toggle between the programs.
timer:* off *
Is the timer program (see section 5.6).
CLEAN
refer to the automatic cleaning program (see section 8.1).
5.2 Pre-heating
When the pre-heat function is activated, the unit will start this function after selecting this program.
The screen will display the current temperature (on the right) and the set pre-heat temperature (on the left).
When the set temperature is reached, the screen will show:
“Load products” and a sound is activated.
22 / 40
5.3 While cooking
During the cooking process, the display shows a graph with the planned temperature trajectory (orange line) and the current temperature (light orange field).
Under the graph, the program name and the total time is shown.
In the bottom of the screen, the current temperature inside the unit and the remaining time are given.
When „cook correction‟ is switched-on, the total time and remaining time will be adjusted.
5.4 Adding extra time to the active program
During the process extra time can be added, by following the next steps:
1. Press the power button.
2. Set extra time by rubbing the rotation pad.
3. Select the arrow point right to save setting.
4. Press OK.
The display now shows the extra time, which will be added to the last cooking step. The screen always shows the total amount of extra time.
ACR
EN 23 / 40
5.5 Interrupt a program
Interrupt temporarily:
1. Press START/PAUSE.
2. Press START/PAUSE again to resume the program.
Interrupt definitely:
1. Press STOP/CANCEL.
2. Select “yes”.
3. Press OK.
ACR
5.6 Set the timer (optional)
This function allows the user to automatically start a program on a pre-determined date and time.
To enable this function, the “timer function” in the Manager menu must be set to “YES”.
To enable this function, the “timer function” in the Manager menu must be set to
“YES”.
1. Select the recipe “timer:*off*.
2. Press OK.
3. Use the arrows to change the setting “timer function” from
“OFF” to “ON”. This setting switches the timer off or on.
4. Press OK twice.
5. Use the arrows to select the desired program, and press
OK.
6. Select “Set time” and press OK.
7. Set the desired time using the rotation pad. By pressing
OK you switch form hours to minutes, and consequently to
“save”. Press OK to save the time setting.
8. Select “Set date”.
9. Select the desired date using the right and left arrow.
10. Select “store” to save the timer settings, and to quit the menu.
11. Once the timer has been set, the top-left of the display will show a flashing clock-sign.
5.7 Reset alarm signal
When an alarm signal has been set, it will sound. To stop this signal, press OK.
5.8 Power down
If no program is active and no key is touched within the next 60 minutes the unit will switch-off automatically.
Press ON/OFF for some seconds to re-start the unit.
This option can be both switched-off or adjusted by a service engineer.
EN 24 / 40
6. SETTINGS
6.1 General
The settings of the unit can be changed by using the control panel.
There are three kinds of settings:
Information
Manager
Service
6.2 Information
6.2.1 Access
1. Activate the settings menu (right selection button).
2. Select “information”.
3. Press OK.
ACR
6.2.2 Overview
The screen shows, for a predefined time, an overview with some pre-programmed settings.
Pressing any knob to return to the setting menu instantaneously.
EN 25 / 40
6.3 Manager
The Manager menu is used to set the parameters.
6.3.1 Access
1. Activate the settings menu (right selection button).
2. Select “manager”.
3. Press OK.
When a pin code has been set:
1. Use the rotation pad to enter the pin code.
2. Press OK or the right arrow to enter the next number.
3. Press OK twice.
ACR
6.3.2 Overview parameters
Setting Function and values
Change pin code Setting the pin code for access to the Manager Menu. This pin code
Save recipes
Load recipes can also be used for access to the Program Menu.
0000 – 9999
to save recipes on an USB stick
to load recipes from an USB stick
Load recipes messages to load recipes messages from an USB stick
Light
ON – OFF
Temperature
Volume Unit
°C – °F
Liter – Gallon
Set time
Set date
Time format
Date format
Alarm signal
Pre heat mode
Pre heat delta
Auto recipe start
Buzzer set
Key beep
Water capacity
Lime filter
Lime filter replaced
Clear error
Setting the current time
Setting the current date
24h – AM/PM
D/M/Y – M/D/Y
YES – NO
NO: never a pre heating
1X: pre heating ONCE, after switching on the unit.
YES: always pre heating
Correction on the pre-heat temperature based upon the operation temperature.
-50°C(-90°F)
– +50°C(+90°F)
NO – YES
Beep 1 – 5
ON – OFF
50 – 30000, “–“ (Liter) / 100 – 7925, “–“ (Gallon)
The displayed value shows the remaining capacity of the lime filter in percentage.
Reset the lime indicator back to 100%
NO – YES (when error is present)
6.4 Service Menu
The service menu contains settings for the language and security of the unit. This can only be accessed by the supplier or a service technician.
EN 26 / 40
7. PROGRAM
ACR
7.1 General
Your dealer has programs that are loaded into the unit by means of a computer. These programs vary with the composition of the product and the customer‟s desire, and are customer dependent.
You can protect the cooking programs and the „secured settings‟ by changing pin code “0000” in the menu, into any other pin code. By changing the pin code back into “0000”, the protection is removed.
The program menu is used to store programs yourself. A program can have not more than 9 steps.
In each step both the temperature and time can be set. The memory can handle 250 programs.
Access:
Activate the program menu (middle selection button).
If a pin code has been set:
1. Use the rotation pad to enter the pin code.
2. Press OK or the right arrow to enter the next number.
3. Press OK twice.
4. Select the desired action.
7.2 Adding programs
1. Select “add program”.
2. Press OK.
7.2.1 Enter the program name
1. Enter the first character by using the rotation pad.
The name can consist of:
letters: “A – Z”
numbers ”0 – 9”
and character “-“ or “blank”
The combination is free to choose. A name cannot have more than 11 characters, including blanks. You can create a blank by skipping a position. This can be done by pressing the right arrow.
2. Press OK or the right arrow to go to the next position.
3. Repeat steps 1 and 2 for the letter/number of the name, if needed.
4. Select the next position with the right arrow.
5. Press OK twice to store the name and to proceed.
6. Select “next”.
7. Press OK
EN 27 / 40
7.2.2 Programming cooking step
The table on the screen contains the following columns:
Time duration
Temperature
Row 1 shows step 1, row 2 shows step 2, etc.
There can be no more than 9 steps.
A selected cell shows an orange frame. To alter a cell, it needs to be „opened‟ by selecting it and pressing OK.
ACR
Setting the time duration
1. Select the time duration of the first cooking step. This is the value in the top-left of the table.
2. Press OK to open the cell. The cell background turns orange.
3. Set the time duration of the step to (1-240 minutes) using the rotation pad.
4. Choose “- “ to skip the step.
5. Press OK to close the cell.
The first cooking step can be set as the preheat step. Set the time setting to “PRE“.
Setting the temperature
1. Use the right arrow to select the cell in the second column.
2. Press OK to open the cell.
3. Set the temperature using the rotation pad.
4. Press OK to close the cell.
Next cooking steps
Select the first cell of the next cooking step to add another cooking step.
7.2.3 Keeping warm (HOLD)
Steps 2 - 9 can be set to keep the products warm. Set the time setting to “HOLD”.
A “keeping warm” step lasts infinitely and it keeps the unit at the desired temperature.
The temperature must be set on at least 85 °C (185 °F).
A warming step is only performed when this is the last step of the program.
7.2.4 Saving the program
1. Select “saving program”.
2. Press OK.
EN 28 / 40
7.3 Edit programs
1. Select “Edit program”.
2. Press OK.
3. Select the required program.
4. Press OK.
ACR
Edit the program name
1. Select the position of the character.
2. Change the character using the rotation pad.
3. Use a „blank‟ to erase a character.
4. Repeat steps 1 and 2 if needed.
5. Select next.
6. Press OK.
Edit the cooking steps
1. Select the cell.
2. Press OK. The cell background turns orange.
3. Set the value using the rotation pad.
4. Press OK to close the cell.
5. Repeat steps 1 - 4 if needed.
6. Select “save program”.
7. Press OK.
EN 29 / 40
7.4 Deleting programs
Deleting of a program cannot be undone .
1. Select “delete program”.
2. Press OK.
3. Select the program.
4. Press OK.
5. Check whether the program name matches the program you wish to delete.
6. Select “yes” if this is the case. Select “no” if not.
7. Press OK.
ACR
7.5 Testing the programs
In the test-mode the program will run normally, but the settings can be changed during the process.
Changes that are made (during testing) in the steps that already are passed, will not affect the products in the unit. However, the changes will be stored and will be active the next time the program is executed.
The changes that are made, will be stored during the testmode.
1. Select “test program”.
2. Press OK.
3. Select the program.
4. Press START/PAUSE or OK.
The process will be running identically to the normal execution of a cooking program. During the process the program can be changed.
1. Press OK.
2. Apply the changes.
3. Select “save program”.
4. Press OK.
EN 30 / 40
7.6 Sorting programs
This function allows you to sort programs alphabetically.
1. Select “sorting alphabetically”.
2. Press OK.
3. Use arrows to select “yes”.
4. Press OK.
ACR
EN 31 / 40
8. CLEANING AND MAINTENANCE
ACR
WARNING
Appliance must be disconnected from the power supply during cleaning or maintenance and when replacing parts.
Do not use aggressive or abrasive materials. These will damage the surface which will make it more difficult to remove dirt.
Clean the inside, the removable parts and the accessories thoroughly with cleanser and water before putting the unit into use. Follow the cleaning instructions as described in this chapter.
Treat the outer surface of the interior window with a soft cleaning agent to protect the reflection layer.
8.1 Periodic maintenance
Item
Interior
Exterior
Action
Clean the interior, see section 8.2.
Clean the exterior using little water, cleaning agent, a soft brush or a sponge.
Dry the exterior with a cloth.
Use Stainless Steel cleaning spray to remove stains, and restoring the gloss.
Cooking area
Pay attention to proper cleanness of items inside the oven.
Put back all accessories.
Glass panes
Open the outer door.
Open the inner door.
Clean the glass panes with warm soapy water or grill
Drip tray
Drain
Grate
Fan plate and fan blade cleaner.
Flush the drip trays located under the inner glass and the rubber with hot water. This to prevent obstruction in the drain and drip trays.
Clean the drain with a drill brush.
Clean the grate. Be sure the grate is always in place.
Check and clean if necessary, see section 8.3.
Frequency
Daily
Weekly
Weekly
Weekly
Weekly
Monthly
Monthly
Monthly
For hygiene matters and optimum state of your ACR, it is advised to maintain a fixed daily cleaning schedule.
EN 32 / 40
8.2 Daily Cleaning
ACR
8.2.1 Automatic cleaning cycle
WARNING
Meat forks and meat baskets must be removed from the equipment during the cleaning program.
1. Remove all meat forks or other accessories.
2. Remove rough fat residues at the drainage grate. The drainage must provide a free flow through during cleaning.
3. Place the grid on the drainage with the convex side up.
4. Check to be sure that there is sufficient cleaning agent present. Otherwise exchange bottle.
5. Press the left-hand selection key.
6. Select “CLEAN”.
7. Press OK.
Contact your supplier for the appropriate cleaning agent.
Consumption per cleaning cycle: approx. 1000 ml.
The unit will now clean itself completely independently. The screen shows the status of the program.
The following steps will be executed (the cleaning program takes about 250 minutes).
1 Steam
2 Cool down
3 Spraying detergent
4 Soaking
5 Steam
3x
6 Rinse
7 Rinse with decalcified water
8 Blow tubes empty
9 Dry
After finishing the cleaning program, the unit switches off automatically.
8.2.2 Clean the accessories
1. Place the detachable parts in a wide rinsing container filled with hot water and an appropriate cleaning agent.
2. Soak these parts for one night and clean them the next day.
EN 33 / 40
ACR
8.3 Fan plate and fan blade
WARNING
Take the power plug from the socket prior applying maintenance.
The fan plate with grid on the side of the ACR needs to be checked once a month, and, depending on the pollution, even more often. This way you can be sure that the ventilation will be optimal. If this is not done as instructed, the cooking time will increase and the unit can get overheated.
1. The plate can be detached without using tools by removing the four wing nuts
2. After taking off, the plate can be cleaned. At the same time the fan can be checked.
If necessary, clean with a cloth and cleaning agent.
3. Remount the fan plate.
EN 34 / 40
9. MALFUNCTIONS AND SERVICE
ACR
Before you contact your supplier/dealer in case of a malfunction, there are some items you can check yourself:
Is the power supply working properly? Check fuses and differential switch.
Has the timer clock been properly set?
Item
Cleaning
Cleaning
Control
Fan
Fan
Lamp
Oven
Oven
Oven
Mains cord
Malfunction
Leaks water during cleaning
Possible action
Door not closed correctly.
Check door seal, replace if necessary.
Oven not clean after cleaning cycle
Not enough detergent, check supply.
No water supply, check.
Drain polluted, clean.
Drain valve not working properly,
Program do not start check.
Check if both doors are closed
Fan not spinning correctly.
Remove the plug from the socket.
Open the door.
Remove fan plate (see section 8.3) and
Noisy fan check what's blocking the fan blade.
Fan polluted, clean (see section 8.3).
Does not light up
Leaks fat
Set OFF in manager menu.
Fat tray not placed (correctly).
Product is not getting done equally
Try a lower cooking temperature.
Check fuses and/or the differential
The oven does not heat up
Damaged switch.
Open and close door.
Check fuses and/or the differential switch.
9.1 Replacing the mains cord
WARNING
Hazardous electrical voltage.
If the mains cord is damaged, it must be replaced by the manufacturer, his service agent or a similarly qualified person in order to avoid hazards.
EN 35 / 40
10. TECHNICAL SPECIFICATIONS
ACR
WARNING
Consult the identification plate to get the proper specifications of the unit. The electrical data may vary from country to country
European Models
Dimensions
Weight
Maximum ambient temperature
Sound pressure
Electrical installation
Plug
1
Water connection
Water
Drain
Cleaning agent
American Models mm mm mm kg kg
°C
Width
Depth
Height
Gross
Net
Voltage dB (A)
V
Frequency
Required power
Hz kW
Max. nominal current A
CEE-form A length
Aerated pressure
Open connection m inch kPa mm mL
ACR
1340
ACR+IC
1340
950 [ SB ], 1065 [ PT ] 950 [ SB ], 1065 [ PT ]
1880
445
380
2216
500
424
35 35
< 70
3N~ 400/230
50/60
12
20
32
< 70
3N~ 400/230
50/60
12
20
32 approx. 2.2
¾
200 – 500 min. 40 approx. 2.2
¾
200 – 500 min. 40 approx. 1000/cycle approx. 1000/cycle
Dimensions approx.
Weight
Maximum ambient temperature
Sound pressure
Electrical installation
Plug
Water connection
Water
Drain
Cleaning agent
Width
Depth
Height
Gross
Net
Voltage
Frequency
Required power
Open connection
[SB = Solid back, PT = Pass through] inch inch inch lbs lbs
°F dB (A)
V
Hz kW
Max. nominal current A
N/A (fixed wiring)
Aerated pressure inch kPa inch mL
ACR
52 ¾
37½ [ SB ], 42 [ PT ]
74
981
838
95
ACR+IC
52 ¾
37½ [ SB ], 42 [ PT ]
87 ¼
1102
935
95
< 70
3N~ 208/115
50/60
12
< 70
3N~ 208/115
50/60
12
35 35
¾
200 – 500 min. 1 ⁄
¾
200 – 500 min. 1 ⁄ approx. 1000/cycle approx. 1000/cycle
1
Depending on Country
EN 36 / 40
11. ACCESSORIES
For the ACR the following accessories are available:
Meat Fork V-spit
Meat basket Chicken rack
ACR
EN 37 / 40
Notes.
ACR
EN 38 / 40
Notes.
ACR
EN 39 / 40
EN 40 / 40
ACR
advertisement
Related manuals
advertisement