BD-E8500A
BD-E8900A
BD-HDD Combo
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/register
02230H-BD-E8900A-XY-ENG.indd 1
Safety Information
Warning
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol indicates "dangerous voltage" CAUTION: TO REDUCE THE RISK OF ELECTRIC This symbol indicates important instructions
inside the product that presents a risk of
SHOCK, DO NOT REMOVE COVER (OR BACK)
accompanying the product.
electric shock or personal injury.
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
Do not install this equipment in a confined space
such as a bookcase or similar unit.
WARNING
o To prevent damage which may result in fire
or electric shock hazard, do not expose this
appliance to rain or moisture.
CAUTION
o BD-HDD COMBO USES AN INVISIBLE LASER
BEAM WHICH CAN CAUSE HAZARDOUS
RADIATION EXPOSURE IF DIRECTED.
BE SURE TO OPERATE BD-HDD Combo
CORRECTLY AS INSTRUCTED.
CAUTION
THIS PRODUCT UTILIZES A LASER. USE
OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT
IN HAZARDOUS RADIATION EXPOSURE. DO
NOT OPEN COVERS AND DO NOT REPAIR
YOURSELF. REFER SERVICING TO QUALIFIED
PERSONNEL.
This product satisfies CE regulations when
shielded cables and connectors are used to
connect the unit to other equipment. To prevent
electromagnetic interference with electric
appliances, such as radios and televisions, use
shielded cables and connectors for connections.
| 2 English
02230H-BD-E8900A-XY-ENG.indd 2
IMPORTANT NOTE
The mains lead on this equipment is supplied with
a molded plug incorporating a fuse. The value of
the fuse is indicated on the pin face of the plug.
If it requires replacing, a fuse approved to BS1362
of the same rating must be used.
Never use the plug with the fuse cover omitted
if the cover is detachable. If a replacement fuse
cover is required, it must be of the same colour as
the pin face of the plug. Replacement covers are
available from your dealer.
If the fitted plug is not suitable for the power points
in your house or the cable is not long enough to
reach a power point, you should obtain a suitable
safety approved extension lead or consult your
dealer for assistance.
However, if there is no alternative to cutting off the
plug, remove the fuse and then safely dispose of
the plug. Do not connect the plug to a mains jack,
as there is a risk of shock hazard from the bared
flexible cord.
To disconnect the apparatus from the mains, the
plug must be pulled out from the mains socket,
therefore the mains plug shall be readily operable.
The product unit accompanying this user manual
is licenced under certain intellectual property rights
of certain third parties.
CLASS 1 LASER PRODUCT
This Compact Disc player is classified as a CLASS
1 LASER product. Use of controls, adjustments
or performance of procedures other than those
specified herein may result in hazardous radiation
exposure.
LASER PRODUCT
LASER PRODUKT
LASER LAITE
LASER APPARAT
LÁSER CLASE 1
Precautions
Important Safety Instructions
Read these operating instructions carefully before
using the unit. Follow all the safety instructions
listed below.
Keep these operating instructions handy for future
reference.
1.
Read these instructions.
3.
Heed all warnings.
2.
4.
5.
6.
7.
8.
Keep these instructions.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including AV receivers) that
produce heat.
Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade
or the third prong are provided for your safety.
If the provided plug does not fit into your
outlet, consult an electrician for replacement
of the obsolete outlet.
10. Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where it exits the
apparatus.
11. Only use attachments/accessories specified
by the manufacturer.
12. Use only with the cart,
stand, tripod, bracket,
or table specified by the
manufacturer, or sold with
the apparatus. When a cart
is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning storms
or when unused for long periods of time.
14. Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as when the power-supply cord or plug
is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does
not operate normally, or has been dropped.
Disc Storage & Management
o Holding Discs
- Fingerprints or scratches on
the disc may reduce sound and
picture quality or cause skipping
- Avoid touching the surface of a disc where
data has been recorded.
- Hold the disc by the edges so that fingerprints
will not get on the surface.
- Do not stick paper or tape on the disc.
English
02230H-BD-E8900A-XY-ENG.indd 3
3|
Safety Information
CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1
PRODUCTO
9.
01
CAUTION :
o CLASS 3B VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN. AVOID EXPOSURE
TO THE BEAM (IEC 60825-1)
o THIS product UTILIZES A LASER. USE
OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION
EXPOSURE. DO NOT OPEN COVER AND DO
NOT REPAIR YOURSELF. REFER SERVICING
TO QUALIFIED PERSONNEL.
Safety Information
o Cleaning Discs
- If you get fingerprints or dirt on the
disc, clean it with a mild detergent
diluted in water and wipe with a
soft cloth.
- When cleaning, wipe gently from
the inside to the outside of the disc.
o Disc Storage
 Do not keep in direct sunlight.
 Keep in a cool ventilated area.
 Keep in a clean protection jacket and store
vertically.
Handling Cautions
o Do not expose this apparatus to dripping or
splashing. Do not put objects filled with liquids,
such as vases on the apparatus.
o To turn this apparatus off completely, you must
pull the power plug out of the wall socket.
Consequently, the power plug must be easily
and readily accessible at all times.
o Do not touch the power plug with a wet hand.
Otherwise, it can cause an electric shock.
o Do not plug multiple electric devices into the
same wall socket. Ovedrloading a socket can
cause it to overheat, resulting in a fire.
o Maintenance of Cabinet.
- Before connecting other components to this
product, be sure to turn them off.
- If you move your product suddenly from a
cold place to a warm place, condensation
may occur on the operating parts and lens
and cause abnormal disc playback. If this
occurs, unplug the product, wait for two
hours, and then connect the plug to the
power outlet. Then, insert the disc, and try to
play back again.
o If the product makes an abnormal noise or
produces a burning smell or smoke, turn off
the power switch immediately and disconnect
the power plug from the wall outlet. Then,
contact the nearest customer service centre for
technical assistance. Do not use the product.
Using the product as it is may cause a fire or an
electric shock.
| 4 English
02230H-BD-E8900A-XY-ENG.indd 4
Using the 3D function
IMPORTANT HEALTH AND SAFETY
INFORMATION FOR 3D PICTURES.
Read and understand the following safety
information before using the 3D function.
o Some viewers may experience discomfort while
viewing 3D TV such as dizziness, nausea, and
headaches.
If you experience any such symptom, stop
viewing 3D TV, remove the 3D Active Glasses,
and rest.
o Watching 3D images for an extended period of
time may cause eye strain. If you feel eye strain,
stop viewing 3D TV, remove your 3D Active
Glasses, and rest.
o A responsible adult should frequently check on
children who are using the 3D function.
If there are any reports of tired eyes, headaches,
dizziness, or nausea, have the child stop viewing
3D TV and rest.
o Do not use the 3D Active Glasses for other
purposes. (Such as general eyeglasses,
sunglasses, protective goggles, etc.)
o Do not use the 3D function or 3D Active Glasses
while walking or moving around. Using the 3D
function or 3D Active Glasses while moving
around may cause you to bump into objects,
trip, and/or fall, and cause serious injury.
o When displaying 3D programme with this
model, the actual screen may appear as shown
below:
Screen Display
Description
Side by Side
Same screen duplicates
horizontally.
Top & Bottom
Same screen duplicates
vertically.
o 3D programme reception, recording and
playback of this model may not fully support
3D, due to the 3D broadcast format is not yet
standardized worldwide. It is not the product’s
malfunction or disorder.
01
o If you want to enjoy 3D content, connect a 3D
device (3D compliant AV receiver or TV) to the
product ’s HDMI OUT port using a high-speed
HDMI cable. Put on 3D glasses before playing
the 3D content.
o The product outputs 3D signals only through
HDMI cable connected to the HDMI OUT port.
o As the video resolution in 3D play mode is fixed
according to the resolution of the original 3D
video, you can not change the resolution to your
preference.
o Some functions such as BD Wise, screen size
adjustment, and resolution adjustment may not
operate properly in 3D play mode.
o You must use a high-speed HDMI cable for
proper output of the 3D signal.
o Stay at least three times the width of the screen
from the TV when watching 3D images. For
example, if you have a 46-inch screen, stay 138
inches (11.5 feet) from the screen.
o Place the 3D video screen at eye level for the
best 3D picture.
o When the product is connected to some 3D
devices, the 3D effect may not function properly.
o "Blu-ray 3D" and "Blu-ray 3D" logo are
trademarks of the Blu-ray Disc Association.
Safety Information
Copyright
© 2012 Samsung Electronics Co.,Ltd.
All rights reserved; No part or whole of this user’s
manual may be reproduced or copied without the
prior written permission of Samsung Electronics
Co.,Ltd.
English
02230H-BD-E8900A-XY-ENG.indd 5
5|
Contents
SAFETY INFORMATION
2
3
3
3
4
4
5
Warning
Precautions
Important Safety Instructions
Disc Storage & Management
Handling Cautions
Using the 3D function
Copyright
GETTING STARTED
8
8
8
8
9
9
10
13
14
14
15
Disc and Format Compatibility
Disc types and contents your product can play
Disc types your product cannot play
Available Recording Time for internal HDD
Region Code
Logos of Discs the product can play
Supported Formats
Accessories
Front Panel
Rear Panel
Remote Control
CONNECTIONS
17
18
18
18
19
19
19
19
20
20
20
Connecting to a TV with an Audio/Video cables
and RF cable
Connecting to a TV
Method 1 Using an HDMI cable (not included) Best Quality (Recommended)
Method 2 Using a Video and an Audio cable Good Quality
Connecting to an Audio System
Method 1 Connecting to an HDMI supported AV
receiver
Method 2 Connecting to an AV receiver with
Optical input
Method 3 Connecting to a Stereo Amplifier with
an Audio Cable
Connecting to a Network Router
Wired Network
Wireless Network
| 6 English
SETTINGS
21
21
21
22
23
31
31
33
34
35
35
35
35
36
36
36
37
37
The Setup Procedure
The Home Screen
Accessing the Settings Screen
Buttons on the Remote Control used for the
Settings menu
Settings Menu Functions
Networks and the Internet
Configuring Your Network Connection
Wi-Fi Direct
Soft AP
AllShare Settings
Device Name
Upgrading Software
Online
By Channel
By USB
By Disc
By Downloaded
Standby Mode Upgrade
MEDIA PLAY
38
38
38
39
40
41
41
41
42
42
42
Insert a Disc to the Disc tray
Insert a USB or Mobile Phone to the USB port
Accessing the AllShare Play Screen
Using the AllShare Play Function
To download the AllShare software
Playing content located in your PC on the BDHDD Combo
Playing content located in your Mobile device on
the BD-HDD Combo
Controlling with your mobile device
Controlling Video Playback
Buttons on the Remote Control used for Video
Playback
Using the Tools Menu
44
44
DTV FUNCTIONS
49
49
50
50
50
50
51
51
52
52
Watching TV Channels
Using the Tools Menu
Using the PIP (Picture-In-Picture) function
Editing Channels
Channel List
Channel Screen
Using the Tools Menu
Viewing the Guide Screen
Schedule Manager
Using the Teletext Service
NETWORK SERVICES
60
60
61
62
62
62
Using Smart Hub
Smart Hub at a Glance
Using the Web Browser
BD-LIVE™
Samsung Smart View
Dual View
Contents
44
44
44
45
45
45
46
46
46
Controlling Music Playback
Buttons on the Remote Control used for Music
Playback
Using the Tools Menu
Repeating Tracks on an Audio CD
Shuffling Tracks on an Audio CD
Creating a Playlist from a CD
Ripping
AMG (All Media Guide) function
Playing Photo Contents
Using the Tools Menu
Using the Tools Menu when a file
is highlighted
APPENDIX
63
64
64
65
68
74
76
77
Compliance and Compatibility Notice
Copy Protection
Network Service Disclaimer
Licence
Additional Information
Troubleshooting
Repairs
Specifications
ADVANCED FUNCTION
54
54
54
55
55
57
57
57
58
58
58
58
58
59
59
Recording
Checking Available Storage Size
Recording the current TV channel you are
watching
Simultaneous Recording
Timeshift function
Playing the Recorded Title
Editing the Recorded Title
Splitting a Section of a Title (Divide into two)
Splitting a Section of a Title (Partial Delete)
Copy
Copying Videos, Music or Photos
3D Functions
3D Converter
Adjusting the 3D Depth
Viewing DTV with the 3D effect
English
7|
Getting Started
Disc and Format Compatibility
Disc types and contents your product can play
Contents
VIDEO
MUSIC
PHOTO
VIDEO
MUSIC
PHOTO
Media
Blu-ray Disc
3D Blu-ray Disc
DVD-VIDEO
DVD±RW/±R
CD-RW/R
CD-RW/R
DVD±RW/±R
BD-RE/R
CD-RW/R
DVD±RW/±R
BD-RE/R
HDD
USB
Details
BD-ROM or BD-RE/R disc recorded in the BD-RE format.
DVD-VIDEO, DVD±RW/±R discs that have been recorded and finalized.
Media containing DivX, MKV or MP4 contents.
Music recorded on CD-RW/R, DVD±RW/±R, BD-RE/R containing MP3 or WMA
contents.
Photos recorded on CD-RW/R, DVD±RW/±R, BD-RE/R media containing JPEG contents.
Video, music and photos stored in HDD or USB.
* For more information on the file format, refer to pages 10~12.
Disc types your product cannot play
o HD DVD
o DVD-ROM/PD/MVDisc, etc
o DVD-RAM
o Super Audio CD
(except CD layer)
| NOTE |
o DVD-RW(VR mode)
o 3.9 GB DVD-R for
Authoring.
o CVD/CD-ROM/CDV/
CD-G/CD-I/LD
(CD-Gs play audio only,
not graphics.)
! The product may not play certain CD-RW/R and DVD±RW/±R because of the recording conditions.
! If a DVD±RW/±R has not been recorded properly in DVD video format, it will not be playable.
! Your product will not play content that has been recorded on a DVD±RW/±R at a bit-rate that exceeds 10Mbps.
! Your product will not play content that has been recorded on a BD-RE/R at a bit rate that exceeds 25Mbps.
! Playback may not work for some types of discs, or when you use specific operations, such as angle change and aspect ratio
adjustment. Information about the discs is written in detail on the disc box. Please refer to this if necessary.
! When you play a BD-J title, loading may take longer than a normal title or some functions may perform slowly.
Available Recording Time for internal HDD
You can record digital broadcast on the internal HDD as below.
Depending on the actual broadcast, available recording time may be different with the table shown below
In On Screen Display, you can check available recording time as shown in "high" case in the table shown below.
| 8 English
02230H-BD-E8900A-XY-ENG.indd 8
SD
5Mbps
(Normal)
HD
Recording Time
BD-E8900A BD-E8500A
20Mbps
102 Hours
49 Hours
411 Hours
199 Hourss
10Mbps (High) 205 Hours
99 Hours
4
DVD-VIDEO
| NOTE |
! Since the product's Timeshift and other implemented
functions require a certain amount of HDD space allocated
internally, the total size shown in the "Storage Device
Manager" of Settings menu may differ from the HDD's
capacity shown in the manual.
Mexico, South America,
Central America, Australia,
New Zealand, Pacific Islands,
Caribbean
5
Russia, Eastern Europe, India,
most of Africa, North Korea,
Mongolia
6
China
Logos of Discs the product can play
Region Code
Both products and discs are coded by region.
These regional codes must match for a disc to play.
If the codes do not match, the disc will not play.
The Region Number for this product is displayed
on the rear panel of the product.
Disc Type
Region
Code
A
Blu-ray Disc
B
C
DVD-VIDEO
Area
North America, Central America,
South America, Korea, Japan,
Taiwan, Hong Kong and South
East Asia.
Europe, Greenland, French
territories, Middle East, Africa,
Australia and New Zealand.
Blu-ray Disc
3D Blu-ray Disc
BD-LIVE
DivX
PAL broadcast System in U.K.,
France, Germany, etc.
India, China, Russia, Central and
South Asia.
1
The U.S., U.S. territories and
Canada
2
Europe, Japan, the Middle East,
Egypt, South Africa, Greenland
3
Taiwan, Korea, the Philippines,
Indonesia, Hong Kong
English
02230H-BD-E8900A-XY-ENG.indd 9
9|
Getting Started
Estimated
Bitrate
02
Broadcast
Type
Getting Started
Supported Formats
Video File Support
File Extension
*.avi
*.mkv
*.asf
*.wmv
*.mp4
*.3gp
*.vro
*.mpg
*.mpeg
*.ts
*.tp
*.trp
*.mov
*.flv
*.vob
*.svi
*.m2ts
*.mts
*.divx
*.webm
Container
AVI
MKV
ASF
MP4
3GP
VRO
VOB
PS
TS
WebM
Video Codec
Divx 3.11/4.x/
5.x/6.x
MPEG4 SP/
ASP
H.264 BP/
MP/HP
Motion JPEG
Window
Media Video v9
Frame rate
(fps)
1920x1080
6~30
Bit rate (Mbps) Audio Codec
30
MPEG2
MPEG1
VP6
4
640x480
30
SVAF
MVC
WebM
Resolution
1920x1080
VP8
 Limitations
24/25/30
40
6~30
8
AC3
LPCM
ADPCM
(IMA, MS)
AAC
HE-AAC
WMA
DD+
MPEG(MP3)
DTS Core
Vorbis
- Even when the file is encoded by a supported codec listed above, a file might not be played if its
content has a problem.
- Normal playback is not guaranteed if the file’s container information is wrong or the file itself is
corrupted.
- Files having higher Bit rate/frame rate than indicated in the table above may stutter when played back.
- Seek (skip) function is not available if the file’s index table is damaged.
- When you playback a file remotely through a network connection, video playback may stutter
depending on the network speed.
- Some USB/Digital camera devices may not be compatible with the product.
 Video decoder
- Supports up to H.264 Level 4.1.
- Does not support H.264 FMO/ASO/RS, VC1 SP/MP/AP L4.
| 10 English
02230H-BD-E8900A-XY-ENG.indd 10
-
Supports WMA 10 PRO (Up to 5.1).
Does not support WMA lossless audio.
Does not support QCELP/AMR NB/WB.
Supports vorbis (Up to 2ch), Supports codec
only in webm container.
- Supported ADPCM IMA, MS. (MULAW, ALAW
are not supported)
| NOTE |
! Playback of some MKV or MP4 file may not be supported
depending on their video resolution and frame rate.
Supported Subtitle File Formats
Name
MPEG-4 Timed text
.smi
SubViewer
.sub
.srt
Micro DVD
.sub or.txt
Advanced SubStation
Alpha
.ass
SubStation Alpha
.ssa
Powerdivx
.psb
SubStation Alpha
MKV
Xsub
Internal
.ttxt
SAMI
SubRip
External
File
Extension
Advanced SubStation
Alpha
AVI
MKV
SubRip
MKV
MPEG-4 Timed text
MP4
File Extension
Type
*.mp3
MPEG
MPEG1 Audio
Layer 3
*.m4a
*.mpa
*.aac
MPEG4
AAC
*.flac
FLAC
FLAC
*.ogg
OGG
Vorbis
*.wma
WMA
WMA
Picture File Support
File Extension
*.jpg
*.jpeg
*.png
*.bmp
*.mpo
Codec
Type
Resolution
JPEG
15360x8640
PNG
BMP
MPO
1920x1080
1920x1080
15360x8640
Notes on the USB connection
o Your product supports USB storage media,
MP3 products, digital cameras, and USB card
readers.
o Some USB/digital camera devices may not be
compatible with the product.
o Your product supports the FAT16, FAT32, and
NTFS files systems (read only).
o Connect USB devices directly to the product’s
USB port. Connecting through a USB cable
may cause compatibility problems.
o Inserting more than one memory device into
a multi-card reader may cause the reader to
operate improperly.
English
02230H-BD-E8900A-XY-ENG.indd 11
11 |
Getting Started
 Audio decoder
Music File Support
02
- CODECs except for MVC, VP8, VP6
1) Below 1280 x 720 : 60 frames max.
2) Above 1280 x 720 : 30 frames max.
3) Does not support GMC 2 or higher.
- Supports SVAF Top/Bottom, Side by Side.
- Supports BD MVC Spec.
Getting Started
o The product supports the PTP protocol.
o Do not disconnect a USB device during a
"loading" process.
o The bigger the image resolution, the longer the
image takes to display.
o This product cannot play MP3 files with DRM
(Digital Rights Management) downloaded from
commercial sites.
o Your product only supports video that is under
30fps (frame rate).
o Your product only supports USB Mass Storage
Class (MSC) devices such as thumb drives,
flash card readers and USB HDD. (HUB is not
supported.)
o Certain USB HDD Devices, multi-card readers
and thumb drives may not be compatible with
this product.
o If some USB devices require excessive power,
they may be limited by the circuit safety device.
o If playback from a USB HDD is unstable, provide
additional power by plugging the HDD into a
wall socket.
If the problem continues, contact the USB HDD
manufacturer.
o You must remove the USB storage device
safely (by performing the "Safely Remove USB"
function to prevent possible damage to the USB
memory).
o SAMSUNG is not responsible for any data file
damage or data loss.
o Your product does not support compression file,
sparse file and encrption file of NTFS.
- Before disconnecting a USB device, please
use USB Safety Removal.
- If you don't use USB Safety Removal, your
data on USB device can be corrupted or lost
- You can repair or format a USB device on
your Desktop PC. (MS-Windows OS only)
| 12 English
02230H-BD-E8900A-XY-ENG.indd 12
Connect a USB device before using the
Timeshift and Recorded TV functions
Do not use a USB memory stick. We
do not support a USB memory stick.
We recommend using a USB HDD
with at least 5400 rpm, but a USB
HDD of RAID type is not supported.
o To use the Timeshift mode or the Recorded
TV function, a connected USB device must be
execute the Device Format function to proper
form for recording.
- During the device formatting, do not
disconnect the device while formatting is in
progress. If you format the device, all files will
be deleted.
- Before formatting your device to this product,
please back up your files to prevent them
from damage or loss of data. SAMSUNG is
not responsible for any data file damage or
data loss.
o Recorded videos are DRM (digital rights
managements) protected and cannot be played
on a PC or other product. Note that files saved
on the TV cannot be used after the main board
is changed.
o At least 100MB of free space is required for
recording.
o Recording will stop if the storage's free space
becomes less than 50 MB.
o If the USB device has failed the Device
Performance Test, the USB device must
go through the Device Format and Device
Performance Test again before you record with
the Guide or Channel Manager.
If the device has failed the Performance Test, It
cannot be used for recording.
AVCHD (Advanced Video Codec High Definition)
! Some AVCHD format discs may not play, depending on the recording condition.
AVCHD format discs need to be finalized.
! "x.v.Color" offers a wider colour range than normal DVD camcorder discs.
Accessories
Check for the supplied accessories below.
FUNCTION
TV SOURCE
POWER
RECEIVER
BD
TV
SUBTITLE
1
2
4
5
7
8
DISC MENU
TTX/MIX
INPUT
3
6
9
TITLE MENU
0
POPUP
TV MUTE
TV SOURCE
CH LIST
A
HOME
B
C
DIGITAL
SUBTITLE
SMART HUB SEARCH
PANDORA
Audio/Video cable
RF cable for TV
Batteries for Remote Control (AAA Size)
User Manual
GUIDE
SOCIAL
REC
SUBTITLE
D
2D 3D
INPUT
REC PAUSE
Remote Control
English
02230H-BD-E8900A-XY-ENG.indd 13
13 |
Getting Started
| NOTE |
02
o This product can play back AVCHD format discs. These discs are normally recorded and used in
camcorders.
o The AVCHD format is a high definition digital video camera format.
o The MPEG-4 AVC/H.264 format compresses images with greater efficiency than the conventional
image compressing format.
o Some AVCHD discs use the "x.v.Color" format. This product can play back AVCHD discs that use
"x.v.Color" format.
o "x.v.Color" is a trademark of Sony Corporation.
o "AVCHD" and the AVCHD logo are trademarks of Matsushita Electronic Industrial Co., Ltd. and Sony
Corporation.
Getting Started
Front Panel
PLAY/PAUSE BUTTON
ENTER BUTTON
STOP BUTTON
POWER BUTTON
EJECT BUTTON
DISC SLOT
DISPLAY
USB HOST
REMOTE CONTROL SENSOR
| NOTE |
! To upgrade the product's software through the USB Host jack, you must use a USB memory stick.
! When the product displays the Blu-ray Disc menu, you cannot start the movie by pressing the Play button on the product or
the remote. To play the movie, you must select Play Movie or Start in the disc menu, and then press the E button.
Rear Panel
ANT OUT (TO TV)
ANT IN
LAN
HDMI OUT
AUDIO OUT
USB HOST
| 14 English
02230H-BD-E8900A-XY-ENG.indd 14
DIGITAL AUDIO OUT
VIDEO OUT
Remote Control
Press this to operate a TV.
Press this to operate BD-HDD Combo.
Press numeric buttons to operate options
or to access channels directly.
Use to enter the disc menu.
FUNCTION
TV SOURCE
POWER
RECEIVER
BD
TV
SUBTITLE
TTX/MIX
INPUT
1
2
3
4
5
6
7
8
DISC MENU
9
TITLE MENU
0
POPUP
Press to skip backwards or forwards.
Mutes the speakers of your TV.
Press this to select a TV channel.
TV SOURCE
CH LIST
HOME
GUIDE
Press to move to the home screen.
Press this to display the playback information
during playing a content in Disc/USB/HDD
or display the information of TV channel.
Use to select menu items and change
menu value.
Return to the previous menu.
Press to exit the menu.
A
B
C
DIGITAL
SUBTITLE
SMART HUB SEARCH
PANDORA
SOCIAL
REC
SUBTITLE
D
2D 3D
INPUT
REC PAUSE
Press this to use web browser function.
Press this to use PIP function.
These buttons are used both for menus on
the product and also several Blu-ray Disc
functions.
Press this when you want to use 3D
function.
Press this to pause during recording.
Press to use social TV.
Installing batteries
After setup, allows you to set the input
source on your TV.
Displays the EPG (Electronic Programme
Guide.)
Press to use Tools menu.
Press to search contents.
Use to enter the popup menu/title menu.
Press this to pause a playback or pause the
Timeshift function.
Press this to play or start the Timeshift
function.
TV MUTE
TV volume adjustment.
Press to use Smart Hub.
Alternately selects Teletext, Double or Mix.
Press to search backwards or forwards.
Stops playback or recording.
Displays channel lists on the screen.
Turn the TV on and off.
Press to eject a disc.
| NOTE |
Press this to make a recording.
! If the remote does not operate properly:
- Check the polarity +/– of the batteries.
- Check if the batteries are drained.
- Check if the remote sensor is blocked by obstacles.
- Check if there is any fluorescent lighting nearby.
| CAUTION |
! Dispose of batteries according to local environmental
regulations. Do not put them in the household trash.
English
02230H-BD-E8900A-XY-ENG.indd 15
15 |
Getting Started
Turn the product on and off.
02
Tour of the Remote Control
Getting Started
Setting the Remote Control to Operate
Your TV
1.
2.
3.
4.
To determine whether your television is
compatible, follow the instructions below.
Turn your television on.
Point the remote control towards the
television.
Press the TV button to set the TV mode.
Press and hold the TV POWER button, and
then enter the two-figure code in the table
to the right that corresponds to the brand of
your television by pressing the appropriate
number buttons.
If your television is compatible with the
remote control, it will Turn off.
The remote is now programmed to operate
the TV.
| NOTE |
! If several codes are listed for your television brand, try
each one in turn until you find one that works.
! If you replace the remote control’s batteries, you must set
the brand code again.
You can control certain functions of your TV with
this remote control.
Button
TV POWER
Number
TV VOL +/–
TV MUTE
PROG (,/.)
TV SOURCE
| NOTE |
Function
Used to Turn the television on and off.
Used to input number directly.
Used to adjust the volume of the
television.
Used to toggle the sound on and off.
Used to select the desired channel.
Used to select an external source
connected to the TV.
! The functions listed above will not necessarily work on all
televisions. If you encounter problems, use the TV remote
control.
| 16 English
TV Control Codes
Brand
SAMSUNG
Code
TV POWER+01, +02,
+03, +04, +05, +06,
+07, +08, +09
AIWA
TV POWER+82
ANAM
TV POWER+10, +11,
+12, +13, +14, +15,
+16, +17, +18
BANG &
OLUFSEN
BLAUPUNKT
BRANDT
BRIONVEGA
CGE
CONTINENTAL
EDISON
TV POWER+57
TV POWER+71
TV POWER+73
TV POWER+57
TV POWER+52
TV POWER+75
DAEWOO
TV POWER+19, +20,
+23, +24, +25, +26,
+27, +28, +29, +30,
+31, +32, +33, +34
EMERSON
TV POWER+64
FINLUX
TV POWER+06,
+49, +57
FERGUSON
FORMENTI
FUJITSU
GRADIENTE
GRUNDIG
HITACHI
IMPERIAL
JVC
LG
LOEWE
LOEWE OPTA
MAGNAVOX
METZ
MITSUBISHI
MIVAR
NEC
NEWSAN
TV POWER+73
TV POWER+57
TV POWER+84
TV POWER+70
TV POWER+49,
+52, +71
TV POWER+60,
+72, +73, +75
Brand
TV POWER+66
NORDMENDE
TV POWER+72,
+73, +75
NOKIA
PANASONIC
PHILIPS
PHONOLA
TV POWER+57
TV POWER+06,
+56, +57
TV POWER+06, +56
RADIOMARELLI TV POWER+57
RCA
TV POWER+45, +46
SABA
TV POWER+57,
+72, +73, +74,
+75
REX
SALORA
SANYO
SCHNEIDER
SELECO
SHARP
SIEMENS
SINGER
TELEAVA
TV POWER+40
TV POWER+06,
+55, +56, +57
RADIOLA
TV POWER+06, +19,
+20, +21, +22, +78
TV POWER+06, +57
TV POWER+53,
+54, +74, +75
TV POWER+58,
+59, +73, +74
SINUDYNE
TV POWER+06, +69
TV POWER+74
PIONEER
TV POWER+52
TV POWER+61, +79
Code
NOBLEX
SONY
TELEFUNKEN
THOMSON
TV POWER+74
TV POWER+74
TV POWER+41,
+42, +43, +44,
+48
TV POWER+06
TV POWER+74
TV POWER+36,
+37, +38, +39,
+48
TV POWER+71
TV POWER+57
TV POWER+57
TV POWER+35, +48
TV POWER+73
TV POWER+67,
+73, +75, +76
TV POWER+72,
+73, +75
THOMSON ASIA TV POWER+80, +81
TV POWER+06,
+48, +62, +65
TOSHIBA
TV POWER+83
YOKO
TV POWER+52, +77
WEGA
TV POWER+68
ZENITH
TV POWER+47,
+48, +49, +50,
+51, +52
TV POWER+57
TV POWER+06
TV POWER+63
Connections
Connecting to a TV with an Audio/Video cables and RF cable
3.
Plug in the product and TV.
4.
Using video/audio cables, connect the VIDEO OUT (yellow) / AUDIO OUT (white and red)
terminals on the rear of the product to the VIDEO IN (yellow) / AUDIO IN (white and red) terminals
of your TV.
Turn on the product and TV.
To ANT IN
To TV
RF cable
R
Red
W
White
Y
Yellow
Audio
Video
To ANT INPUT
| NOTE |
! The RF cable connection of this product sends only signals of TV. You must connect the Audio/Video cables to watch output
from your product.
! Noise may be generated if the audio cable is placed too close to the power cable.
! If you want to connect to an AV receiver, please refer to the AV receiver connection pages. (See page 19)
! The number and position of terminals may vary depending on your TV set. Please refer to the user manual of your TV.
! If there is only one audio input terminal on the TV, connect it to the AUDIO OUT (Red/white) terminal of the product.
| CAUTION |
! Do not connect the product to your TV through a VCR. Video signals fed through VCRs may be affected by copyright
protection systems and the picture will be distorted on the television.
English
17 |
Connections
Connect the RF cable as shown.
2.
03
1.
Connections
Connecting to a TV
1.
Connect the product to your TV using one of the methods illustrated below.
3.
Press the input selector on your TV remote control until the signal from the product appears on the
TV screen.
2.
Turn on the product and TV.
- Do not connect the power cord until you have made all the other connections.
- When you change the connections, turn off all devices before you start.
Method 1 Using an HDMI cable (not included) - Best Quality (Recommended)
Method 2 Using a Video and an Audio cable - Good Quality
Audio
Video
Method 1
Audio
Match the colours
Method 2
R
Red
W
White
Y
Yellow
Video
Match the colours
| NOTE |
! If you use an HDMI-to-DVI cable to connect to your display device, you must also connect the Digital Audio Out on the
product to audio system to hear audio.
! An HDMI cable outputs digital video/audio, so you don’t need to connect an audio cable.
! Depending on your TV, certain HDMI output resolutions may not work. Please refer to the user manual of your TV.
! When you connect the product to the TV using the HDMI cable for the first time or to a new TV, the HDMI output resolution
will be automatically set to the highest supported by the TV.
! A long HDMI cable may cause a screen noise. If this occurs, set Deep Colour to Off in the menu.
! If the product is connected to your TV in the HDMI 720p, 1080i, or 1080p output mode, you must use a High speed (category
2) HDMI cable.
! HDMI outputs only a pure digital signal to the TV.
If your TV does not support HDCP (High-bandwidth Digital Content Protection), random noise appears on the screen.
! You must have an HDMI connection to enjoy videos with 3D technology.
| 18 English
02230H-BD-E8900A-XY-ENG.indd 18
Connecting to an Audio System
Press the input selector of the connected audio system and TV until the video signal from the
product appears on your TV and you hear the audio signal through your audio system.
Method 1 Connecting to an HDMI supported AV receiver
o Use an HDMI cable (not included)
o Best quality (Recommended)
Method 2 Connecting to an AV receiver with Optical input
o Use an Optical Cable (not included)
o Better quality
o You will hear sound only throuugh the front two speakers with Digital Output set to PCM.
Method 3 Connecting to a Stereo Amplifier with an Audio Cable
o Good Quality
Method 2
Method 3
Audio
Audio
Method 1
R
Red
W
White
Audio/Video
English
02230H-BD-E8900A-XY-ENG.indd 19
19 |
Connections
3.
You can connect the product to an audio system using one of the three methods illustrated below.
Turn on the product, audio system and TV.
- Do not connect the power cord until you have made all the other connections.
- When you change the connections, turn off all devices before you start.
03
1.
2.
Connections
Connecting to a Network Router
Wireless Network
You can connect your product to your network
router using one of the methods illustrated below.
Wired Network
Wireless Router
Or
Broadband modem
(with integrated router)
Broadband
service
Broadband
service
| NOTE |
! If the wireless router supports DHCP, your product can
use a DHCP or static IP address to connect to the wireless
network.
Router
Broadband
modem
Broadband
service
| NOTE |
! Internet access to Samsung’s software update server
may not be allowed, depending on the router you use or
your ISP’s policy. For more information, contact your ISP
(Internet Service Provider).
! DSL users, please use a router to make a network
connection.
! To use the AllShare function with your PC, you must
connect your PC.
! Set your wireless router to Infrastructure mode. Ad-hoc
mode is not supported.
! The product supports only the following wireless security
key protocols:
- WEP (OPEN/SHARED), WPA-PSK (TKIP/AES),
WPA2-PSK (TKIP/AES)
! Select a channel on the wireless router that is not
currently being used. If the channel set for the wireless
router is currently being used by another device nearby, it
will result in interference and communication failure.
! If you select the Pure High-throughput (Greenfield)
802.11n mode and set the Encryption type on your router
or router to WEP, TKIP or TKIP-AES (WPS2Mixed), the
product will not support a connection in compliance with
new Wi-Fi certification specifications.
! If your router supports WPS (Wi-Fi Protected Setup),
you can connect to the network via PBC (Push Button
Configuration) or PIN (Personal Identification Number).
WPS will automatically configure the SSID and WPA key
in either mode.
! Wireless LAN, by its nature, may cause interference,
depending on the operating conditions (router
performance, distance, obstacles, interference by other
radio devices, etc).
! To use the AllShare function with your PC, you must connect
your PC.
| 20 English
02230H-BD-E8900A-XY-ENG.indd 20
Settings
The Setup Procedure
Schedule Manager : Lets you set or edit recording
schedules.
4
Settings : Opens the Settings menu.
5
 To select an option on the Home screen:
The Setup Procedure lets you set the OSD and
menu languages, configure the connection to your
home network, choose the aspect ratio output
(screen size and format) that is correct for your TV,
and search desired channels.
1.
Use the ◄► buttons to move the cursor so
that it highlights your choice, and then press
E button.
Display
| NOTE |
Audio
! When the product is connected to the TV for the first
time, the product turns on automatically. This is normal
operation.
Channel
Network
! Password : Enter the desired 4-digit password using the
number buttons.
- Default password is set to 0000.
The Home Screen
Settings
2
Smart Hub
AllShare Play
Channel
Smart Hub Screen Size
BD Wise
16:9 Original
Size 3
On
Resolution
Auto
Movie Frame (24Fs)
Auto
HDMI Deep Colour
Auto
DTV Smart Resolution
HDMI Colour Format
Off
Auto
| NOTE |
3
4
Accessing the Settings Screen
1.
5
1
1
Support
TV Aspect Ratio
! In the Home menu screen, it will switch to DTV Channel
mode after 3 minutes. When accessing the Settings
menu, the screen saver will be activated after 5 minutes.
Set various functions to suit your personal preferences.
2
System
3D Settings
Schedule Manager
Smart Hub : Starts Smart Hub. From Smart Hub,
you can access YouTube, games, and other apps.
2.
Select Settings on the Home screen, and
then press E button.
The Settings screen appears.
To access the Settings menus, sub-menus,
and options, please refer to the remote
control illustration and the setting table (See
pages 22~30).
AllShare Play : Lets you select contents located on
connected devices by type to view or play. You can
select videos, photos, or music.
English
02230H-BD-E8900A-XY-ENG.indd 21
21 |
Settings
o The Home screen will not appear if you do not
configure the initial settings.
o The OSD (On Screen Display) of this product may
change after you upgrade the software version.
o The access steps may differ depending on the menu
you selected.
04
Channel : Lets you configure your TV channels with
features such as country and auto tune.
3
Settings
Buttons on the Remote Control used
for the Settings menu
CH LIST
1
HOME
GUIDE
3
2
1
2
3
4
4
HOME Button : Press to move to the Home screen.
RETURN Button : Return to the previous menu.
E (Enter) / DIRECTION Buttons :
o Press ▲▼◄► to move the cursor or select an
item.
o Press the E button to activate the currently
selected item or confirm a setting.
EXIT Button : Press to exit the current menu.
Detailed Function Information
Each Settings function, menu item, and individual
option is explained in detail on-screen. To view an
explanation, use the ▲▼◄► buttons to select the
function, menu item, or option. The explanation
will usually appear on the screen.
A short description of each Settings function
starts on the next page. Additional information on
some of the functions is also in the Appendix of
this manual.
| 22 English
02230H-BD-E8900A-XY-ENG.indd 22
Settings Menu Functions
TV Aspect Ratio
Smart Hub Screen Size
BD Wise
Resolution
DTV Smart Resolution
Movie Frame (24Fs)
Lets you adjust the output of the product to the screen
size of your TV.
Lets you select the optimal size for the Smart Hub
Screen.
BD Wise is Samsung’s latest inter-connectivity feature.
When you connect a Samsung product and a Samsung
TV with BD Wise to each other via HDMI, and BD Wise
is on in both the product and TV, the product outputs
video at the video resolution and frame rate of the Bluray/DVD.
Set the output resolution of the HDMI video signal.
The number indicates the number of lines of video per
frame.
The i and p indicate interlaced and progressive scan,
respectively.
The more lines, the higher quality.
Use this function to automatically optimise screen
resolution for digital broadcasts.
| NOTE |
! When you use the BD wise function, this menu will not
appear.
Setting the Movie Frame (24Fs) feature to Auto lets the
play adjust its HDMI output to 24 frames per second for
improved picture quality.
o You can enjoy the Movie Frame (24Fs) feature only on
a TV supporting this frame rate.
o Movie Frame is only available when the product is in
the HDMI 1080i or 1080p output resolution modes.
| NOTE |
! When you use the BD wise function, this menu will not
appear.
English
02230H-BD-E8900A-XY-ENG.indd 23
23 |
Settings
3D Settings
Select whether to play a Blu-ray Disc with 3D contents
in 3D Mode.
o If you move to the Home or Smart Hub Home screen
while in 3D mode, the product will switch to 2D
automatically.
04
Display
Settings
Display
HDMI Colour Format
HDMI Deep Colour
Progressive Mode
Audio
Digital Output
PCM Downsampling
Lets you set the colour space format for HDMI output
to match the capabilities of the connected device (TV,
monitor, etc).
Lets you output video from the HDMI OUT jack with
Deep colour. Deep colour provides more accurate
colour reproduction with greater colour depth.
Lets you improve picture quality when viewing DVDs.
Set Digital output option suitable for your TV or AV
Receiver. For more details, please refer to the digital
output selection table. (See pages 72~73)
Set whether to use downsampling processing or not.
Set Dynamic Range control option for Dolby Digital,
Dolby Digital Plus and Dolby TrueHD.
Auto : The Dynamic Range will be controlled
automatically based on the information provided by
the Dolby TrueHD Soundtrack. This setting is same
with "On" for Dolby Digital and Dolby Digital Plus.
Dynamic Range Control
Off : You can enjoy original sound without
compressing Dynamic Range of the sound.
On : The Dynamic Range is compressed appropriately
by boosting low level sound and reducing extremely
loud sound.
Downmixing Mode
DTS Neo:6 Mode
Audio Sync
Select Downmix method for stereo output.
You can enjoy multichannel sound via HDMI output even
for 2 channels audio source.
In some cases when the product is connected to a
digital TV, the audio signal may not synchronize with the
video signal. If this occurs, adjust the audio delay time
to match the video signal.
o You can set the audio delay time between 0 msec
and 200 msec.
Adjust it to the optimal setting.
| NOTE |
! The audio delay time you specify may not be exact depending
on the played content.
| 24 English
02230H-BD-E8900A-XY-ENG.indd 24
! For users whose TV is the only sound-producing device:
- If the TV does not support Dolby Digital bitstream input via
HDMI, no specific setting is required.
- If the TV supports Dolby Digital bitstream input via HDMI,
set "Digital Output" to "PCM".
By doing so, the "Connected Device" will not require
further setup.
! If the DTV Program you are watching is produced according
to EBU R128, The Average Loudness between MPEG1 Layer2
Audio and Dolby Digital / Dolby Digital Plus audio can be
reduced. If the DTV Program do not meet the EBU R128,
There may be still some amount of difference of average
Loudness between a TV Programs.
! Substantial number of AV Receiver / Home Theatre Device
decode Dolby Digital / Dolby Digital Plus with +4dB OFFSET
when compared to same encoding level of PCM input.
This kind of product include both THX Certified one and also
none THX Certified one.
If user select "AV Receiver(Offset mode)", the average
loudness between Dolby Digtial / Dolby Digital Plus audio
decoded by such a product and MPEG1 Layer2 Audio
decoded by this product will be similar.
English
02230H-BD-E8900A-XY-ENG.indd 25
25 |
Settings
Connected Device
| NOTE |
04
Choose an equipment that you have connected to this
product to hear the sound in addition to your TV.
Loudness of DTV Program will be adjusted according to
your equipment.
AV Receiver : Select this If you use a general AV
Receiver / Home Theatre Equipment or a Television to
hear sound.
AV Receiver (Offset Mode) : Slect this if your case is
one of two shown below.
- If you use THX Certified AV Receiver / Home
Theatre Equipment.
- In case "Digital Output" is set to "Bitstream",
and If you feel the the Dolby Audio much louder
than MPEG1 Layer2 Audio while watching DTV
Program, select this even if your AV Receiver is
not THX Certified one.
Stereo Device : Select this if you use a Stereo
Amplifier or Recording Device that support Optical
Digital Audio Input as PCM format.
Audio
Settings
Channel
Country
Auto Tuning
Manual Tuning
Transfer Channel List
| 26 English
Select this to change the country.
Enter the desired 4-digit password using the number
buttons. Default password is set to 0000.
| NOTE |
! Password : Enter the desired 4-digit password using the
number buttons.
- Default password is set to 0000.
Scans for all channels with active broadcast stations
and stores them.
Scans for a channel automatically and stores in the
product.
Automatically allocated programme numbers may not
correspond to actual or desired programme numbers.
Scans for a channel manually and stores in the product.
When scanning has finished, channels are updated in
the channel list.
This function can import or export the channel map.
You should connect a USB storage to use this function.
Export to USB : Export channel list to USB.
This function is available when USB is connected.
Import from USB : Import channel list from USB.
Network
Wi-Fi Direct
Soft AP
AllShare Settings
Device Name
BD-Live Settings
System
Setup
Lets you check the current network and Internet status.
Lets you connect a Wi-Fi Direct device to the product
using a peer-to-pear network, without a wireless router.
By Wi-Fi Direct, you may use one device to control other
devices.
Lets you connect other types of Wi-Fi devices to the
product wirelessly. Requires that you create a security
key which you must enter into the other Wi-Fi devices
when you are connecting them to the network.
Manage your network connected devices and set this
product's hard drive sharing options.
Device List : Set whether to allow a network
connected device, like a mobile device or tablet, to
share content with or control this product.
Share hard drive : Set whether to share contents
from this product with other network connected
devices, such as mobile devices.
Lets you input a name for the product that will identify it
on your networks.
Set various BD-Live function. BD-Live allows you to
access extra features available on some Blu-ray discs if
you are connected to the Internet.
BD-Live Internet Connection : Lets you fully allow,
partly allow, or prohibit a BD-Live Internet connection.
Delete BD Data : Manage BD data downloaded from
a BD-Live service to Blu-ray discs.
Sets the channels and the time when setting up this
product for the first time or when resetting it.
Sets the current date and time.
| NOTE |
Clock
! If Schedule Viewing and Schedule Recording is set using
GUIDE, Channel List, or Info menu, It will work based on the
time information of the TV programme.
If you set the Clock Mode to Manual and change time
manually, Schedule Viewing and Schedule Recording function
can be limited or work abnormally.
English
27 |
Settings
Network Status
Configure the network connection so you can enjoy
various features such as Internet services or AllShare
Wi-Fi functionality, and perform Software Updates.
04
Network Settings
Settings
System
Anynet+(HDMI-CEC)
Anynet+ is a convenient function that offers linked
operations with other Samsung products that have the
Anynet+ feature. To operate this function, connect this
product to an Anynet+ Samsung TV using an HDMI cable.
Manage storage devices such as internal HDD or an
external HDD connected via USB port for recording.
Format Device : Format selected device. All contents
will be deleted from that device.
Check Device : Check to see if there is an error with
the selected device.
Device Performance Test : Test the recording
performance of the device.
Storage Device Manager
Select Device for Recording : Change the location
of where you store recorded files.
| NOTE |
! Since the product's Timeshift and other implemented
functions require a certain amount of HDD space allocated
internally, the total size shown in the "Storage Device
Manager" of Settings menu may differ from the HDD's
capacity shown in the manual. (See page 54)
You can connect a wireless USB keyboard or mouse to
the USB port on the front of the product.
Keyboard settings : Lets you configure a wireless
USB keyboard connected to the product.
| NOTE |
Device Manager
! You can use the Keyboard only when a QWERTY keyboard
screen or window appears in the Web Browser and Smart Hub.
Mouse settings : Lets you configure a wireless USB
mouse connected to the product. You can use the
mouse in the product's menu in the same way you
use a mouse on your PC.
| NOTE |
! You can use the mouse only when a screen or window appears
in the Web Browser and Smart Hub.
| 28 English
02230H-BD-E8900A-XY-ENG.indd 28
System
 To use a mouse with the product's menu:
3.
Click the menu options you want.
Device Manager
Click the primary button you selected in Mouse
Settings. The Simple Menu appears.
| NOTE |
! Depending on the model of the USB HID keyboard and mouse
may not be compatible with your product.
! Some HID keyboard keys may not work.
! Wired USB keyboards are not supported.
! Some applications may not be supported.
! If a wireless HID Keyboard does not operate because of
interference, move the keyboard closer to the product.
Language
Digital Text
Security
You can select the desired language.
o The selected language will only appear if it is
supported.
If the programme broadcasts with digital text, this
feature is enabled.
This function works in conjunction with Blu-ray Disc/
DVDs that have been assigned an age rating or numeric
rating that indicates the maturity level of the content.
These numbers help you control the types of Bluray Disc/DVDs that your family can watch. When you
access this function, the security screen appears.
Enter the your Security password.
(The default password is 0000.)
DTV Channel Lock : You can lock some channels
using the Channel Lock function so that children
cannot watch them.
DTV Program Rating Lock : This function works
in conjunction with DTV that have been assigned a
rating, which helps you control the types of DTV that
your family watches. Select the rating level you want
to set.
BD Parental Rating : Prevent playback of Blu-ray
Discs with specific age ratings unless a password is
entered.
DVD Parental Rating : Prevent playback of DVDs
with specific numerical ratings unless a password is
entered.
A larger number indicates that the programme is
intended for adult use only.
Change PIN : Change the 4-digit password used to
access security functions.
English
02230H-BD-E8900A-XY-ENG.indd 29
29 |
Settings
Connect the USB mouse to the product.
2.
04
1.
Settings
System
 If you forgot your password
1.
2.
Security
3.
Press the HOME Button to move to the Home
screen.
Remove any disc or USB storage device.
Press and hold the @ button on the front panel
for 5 seconds or more.
All settings will revert to the factory settings.
| NOTE |
! Password : Enter the desired 4-digit password using the
number buttons.
- Default password is set to 0000.
General
You can change the options listed below to match your
preferences.
Advanced Music Copy : When you copy music files,
information can be updated automatically.
The copying time may be increased.
| NOTE |
! This feature is available only when the product is connected
to the network
Menu Transparency : Adjust the transparency of the
menu box.
DivX® Video On Demand
Support
Software Update
Contact Samsung
Remote Management
View DivX® VOD Registration Codes to purchase and
play DivX® VOD contents.
Software Update menu lets you upgrade your product’s
software to the latest version.
Provides contact information for assistance with your
product.
Remote management lets our Call Centre access your
samsung product remotely to troubleshoot a problem.
To use this program, please accept the Terms of Service
Agreement.
| NOTE |
! To connect to remote management, please contact our call
centre first.
! Remote management service might not be available in some
countries.
Reset
| 30 English
02230H-BD-E8900A-XY-ENG.indd 30
Resets all settings to their default settings except for the
network and Smart Hub settings.
The default security PIN is 0000.
Networks and the Internet
Wired - Manual
1.
Select Start in the Network Settings screen,
and then press the E button.
The Network Status screen appears.
The product will verify the network connection.
Configuring Your Network Connection
Before you begin, contact your ISP to find out
if your IP address is static or dynamic. If it is
dynamic, and you have a wired or wireless
network, we recommend using the Automatic
configuration procedures described below.
If you are connecting to a wired network, connect
the product to your router using a LAN cable
before you start the configuration procedure.
If you are connecting to a wireless network,
disconnect any wired network connection before
you begin.
To begin configuring your network connection,
follow these steps:
1.
2.
3.
4.
In the Home screen, select Settings, and
then press the E button.
Select Network, and then press the E
button.
Select Network Settings, and then press the
E button.
Go to the instructions for Wired networks
starting below or the instructions for Wireless
networks starting on page 32.
Wired Network
!
Wired - Automatic
After following Steps 1 to 3 above:
1.
Select Start in the Network Settings screen,
and then press the E button. The product
detects the wired connection, verifies the
network connection and then connects to the
network.
Network Settings
Wired network connection failed.
MAC Address
IP Address
Subnet Mask
Gateway
DNS Server
XX:XX:XX:XX:XX:XX
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
Unable to connect to the network. Try the following: check if your
IP address is set correctly in IP Settings. Contact your Internet
service provider for more information.
2.
3.
4.
Previous
IP Settings
Retry
OK
Select IP Settings on the right of the screen,
and press the E button.
The IP Settings screen appears.
Select the IP Mode field, and then set it to
Manual.
Use the number keypad on your remote to
enter the Network values. Use the ▲▼◄►
buttons on the remote to move from entry
field to entry field.
| NOTE |
! You can get these values from your Internet provider. You
can also view these values on most Windows computers.
For instructions, see "Getting the Network Settings
Values." on page 32.
5.
When done, highlight OK, and then press
E button. The product verifies the network
connection and then connects to the
network.
English
02230H-BD-E8900A-XY-ENG.indd 31
31 |
Settings
If you have a static IP address or the Automatic
procedure does not work, you'll need to set the
Network Settings values manually.
After following Steps 1 to 3 above:
04
When you connect this product to a network,
you can use network based applications and
functions such as Smart Hub and BD-LIVE, and
upgrade the product's software through the
network connection. For more information about
accessing and using Internet services, see the
Network Services chapter of this manual on pages
60~62. Instructions for configuring the network
connection start below.
!
Settings
< Getting the Network Settings Values >
You can view your Network Settings values on
most Windows computers. To view the Network
Settings values, follow these steps:
o Windows XP
1.
2.
3.
4.
!
Wireless (General) - Automatic
After following Steps 1 to 3 in "Configuring Your
Network Connection" on page 31.
1.
Select Start in the Network Settings screen,
and then press the E button.
The product searches for and then displays a
list of the available networks.
Right click the Network icon on the bottom
right of the Windows desktop.
In the pop-up menu, click Status.
Network Settings
On the dialog that appears, click the Support
tab.
Select your wireless router from the list.
iptime23
On the Support tab, click the Details button.
The Network settings are displayed.
ELT
JSY
o Windows 7
1.
2.
3.
4.
KT_WLAN_C361
Mirhenge_edu
Click the Network icon on the bottom right of
the Windows desktop.
In the pop-up menu, click Network and
Sharing Centre.
On the dialog that appears, click the Local
Area Connection or Wireless Network
Connection depending on your network
connection.
On the Support tab, click the Details button.
The Network settings are displayed.
SO070VOIP
2.
Wireless Network
You can setup a wireless network connection in
three ways:
- Wireless Automatic
- Wireless Manual
- WPS(PBC)
When you configure the wireless network
connection, any wireless network devices
currently connected through the product will be
disconnected.
| NOTE |
! Wireless network connection cannot be configured if
Wired internet connection is already established.
| 32 English
02230H-BD-E8900A-XY-ENG.indd 32
Previous
Next
Cancel
Select the desired network, and then press
the E button.
Select Next, and then press the E button
again.
3.
4.
On the Security screen, enter your network's
Security Code or Pass Phrase.
Enter numbers directly using the number
buttons on your remote control. Enter letters
by selecting a letter with an arrow button, and
then pressing E button.
| NOTE |
! Depending on your Windows version, the information may
differ.
Refresh
WPS(PBC)
5.
When done, select Next at the right of the
screen. The product verifies the network
connection and then connects to the
network.
| NOTE |
! If the desired router is not visible or if too many routers
are listed, perform the following instructions. You can
connect to a desired router.
1)
2)
3)
4)
Perform up to step 2 above.
Select Add Network.
Provide a name (SSID) for the wireless router.
Select security type.
! You should be able to find the Security Code or Pass
Phrase on one of the set up screens you used to set up
your router or modem.
!
Wireless (General) - Manual
2.
3.
4.
5.
6.
7.
8.
9.
Select Start in the Network Settings screen,
and then press the E button. The product
searches for and then displays a list of the
available networks.
1.
2.
Select the desired network, and then press
the E button.
Select Next, and then press the E button
again.
On the Security screen, enter your network's
Security Code or Pass Phrase. Enter
numbers directly using the number buttons
on your remote control. Enter letters by
selecting a letter with the ▲▼◄► buttons,
and then pressing the E button.
When done, select Next at the right of the
screen, and then press the E button.
The Network Status screen appears.
The product attempts to verify the network
connection and fails.
Select IP Settings on the right of the screen,
and press the E button. The IP Settings
screen appears.
Select the IP Mode field, and then set it to
Manual.
Use the number keypad on your remote to
enter the Network values. Use the ▲▼◄►
buttons on the remote to move from entry
field to entry field.
| NOTE |
! You can get these values from your Internet provider. You
can also view these values on most Windows computers.
For instructions, see "Getting the Network Settings
Values." on page 32.
10. When done, highlight OK, and then press E
button. The Network Status screen appears.
The product verifies the network connection
and then connects to the network. When it
is done, highlight OK, and then press E
button.
Select Start in the Network Settings screen,
and then press the E button.
The product searches for and then displays a
list of the available networks.
Press the WPS(PBC) button on your
router within two minutes. Your product
automatically acquires all the network
settings values it needs and connects to your
network.
The Network Status screen appears. The
product connects to the network after the
network connection is verified.
Wi-Fi Direct
The Wi-Fi Direct function allows you to connect
Wi-Fi Direct devices to the product and each other
using a peer-to-peer network, without a wireless
router.
1.
2.
3.
4.
Turn on the Wi-Fi direct device and activate
its Wi-Fi Direct function.
In the Home screen, select Settings, and
then press the E button.
Select Network, and then press the E
button.
Select Wi-Fi Direct, and then press the E
button.
The Wi-Fi Direct devices that you can
connect appear.
Wi-Fi Direct
Device
Name : [HDD]E8900
Display
Select your Wi-Fi Direct device to connect to.
Audio
AndroidXXXXXXX
Network
System
Support
Disconnected
Refresh
Close
' Return
English
02230H-BD-E8900A-XY-ENG.indd 33
33 |
Settings
1.
WPS(PBC)
After following Steps 1 to 3 in "Configuring Your
Network Connection" on page 31.
04
If you have a static IP address or the Automatic
procedure does not work, you'll need to set the
Network Settings values manually.
After following Steps 1 to 3 in "Configuring Your
Network Connection" on page 31.
!
Settings
5.
You have three ways to complete the Wi-Fi
connection:
o Through the Wi-Fi device.
o Through the product using PBC.
o Through the product using a PIN.
Each is covered below.
Through the Wi-Fi Device
1.
2.
3.
On the Wi-Fi device, follow the procedure on
the device for connecting to another Wi-Fi
Direct device. See the device's user manual
for instructions.
When you have completed the procedure,
you should see a pop-up on your TV screen
saying that a device that supports Wi-Fi
Direct has requested to connect. Select OK,
and then press the E button to accept.
The Connecting pop-up appears, followed
by the Connected pop-up. When it closes,
you should see the device listed on the Wi-Fi
Direct screen as connected.
Through the Product Using PBC
1.
2.
3.
4.
Select the Wi-Fi Direct device you want to
connect to this product, and then press the
E button. The PBC/PIN pop up appears.
Select PBC, and then press the E button.
The PBC pop-up appears.
Press the PBC button on the Wi-Fi Direct
device within 2 minutes.
The Connecting pop-up appears, followed
by the Connected pop-up. When it closes,
you should see the device listed on the Wi-Fi
Direct screen as connected.
Through the Product Using a PIN
1.
2.
Select the Wi-Fi Direct device you want to
connect to this product, and then press the
E button. The PBC/PIN pop up appears.
Select PIN, and then press the E button.
The PIN pop-up appears.
| 34 English
02230H-BD-E8900A-XY-ENG.indd 34
3.
4.
Note the PIN code in the pop-up, and then
enter it into the appropriate field in the Wi-Fi
Direct device you want to connect.
The Connecting pop-up appears, followed
by the Connected pop-up. When it closes,
you should see the device listed on the Wi-Fi
Direct screen as connected.
| NOTE |
! The wired or wireless network connection will be
disconnected when you use the Wi-Fi Direct function.
! Some Wi-Fi Direct devices may not support the AllShare
function if connected via Wi-Fi Direct. If this is the case,
it is advisable to change the network connection method
between devices.
Soft AP
This product provides a function as a wireless
Access Point.
Soft AP lets you connect other Wi-Fi devices to
your network wirelessly through the product.
It requires that you create a security key which you
must enter into the other Wi-Fi devices when you
are connecting them to the network.
1.
2.
3.
4.
In the Home screen, select Settings, and
then press the E button.
Select Network, and then press the E
button.
Select Soft AP, and then press the E
button.
Select On or Off, and then press the E
button.
< To Set the Soft AP Security Key >
1.
2.
3.
On the Soft AP screen, select Security Key,
and then press the E button. The Security
Key screen appears.
On the Security key screen, enter a security
key. Enter numbers directly using the number
buttons on your remote control. Enter
letters by selecting a letter with the ▲▼◄►
buttons, and then pressing the E button.
When done, use the the ▲▼◄► buttons to
move to DONE at the bottom of the screen,
and then press the E button.
The AllShare Settings screen lists your network
connected AllShare devices and their IP
addresses. Through this screen, you can allow
a device to access the product, deny access, or
delete the device from the AllShare list.
1.
2.
3.
4.
5.
In the Home screen, select Settings, and
then press the E button.
Select Network, and then press the E
button.
Select AllShare Settings, and then press the
E button.
The Software Update menu allows you to
upgrade the product's software for performance
improvements or additional services.
o Never turn the product off or back on manually during
the update process.
1.
2.
3.
4.
The AllShare Settings screen only displays devices
if you have estblished network connections to
AllShare devices. For more information about
AllShare networked devices, see page 41.
| NOTE |
! The "Share hard drive" option should be set to On to
share the contents through AllShare function.
Device Name
Lets you input a name for the product that will
identify it on your networks.
Select Support, and then press the E
button.
Select Software Update, and then press the
E button.
Select one of the following methods:
o Online
o By Channel
Select Device List, and then press the E
button. In the Device List, select a device,
and then press the E button.
The AllShare Settings pop-up appears.
Select Allow, Deny, or Delete from List, and
then press the E button.
In the Home screen, select the Settings, and
then press the E button.
o By USB
o By Disc
o By Downloaded
5.
o Standby Mode Upgrade
Press the E button.
| NOTE |
! The upgrade is complete when the product turns off, and
then turns on again by itself.
! Samsung Electronics shall takes no legal responsibility
for product malfunction caused by an unstable Internet
connection or consumer negligence during a Software
update.
! If you want to cancel the upgrade while the upgrade
software is downloading, press the E button.
Online
Your product must be connected to the Internet to
use the Online function.
1.
2.
Select Online, and then press the E button.
The Connecting to Server message appears.
If there is a download available, the Download
pop-up appears with a progress bar and the
download starts.
English
02230H-BD-E8900A-XY-ENG.indd 35
35 |
Settings
AllShare Settings
Upgrading Software
04
When you connect a Wi-Fi device through the
connection procedure on the device, you must
enter the security key you created here into the
appropriate field.
Settings
3.
4.
5.
When the download is complete, the
Upgrade Query window appears with three
choices: Upgrade Now, Upgrade Later, or
Don't Upgrade.
If you select Upgrade Now, the product
upgrades the software, turns off, and then
turns on automatically.
If you do not make a selection in one minute
or select Upgrade Later, the product stores
the new upgrade software. You can upgrade
the software later using the By Downloaded
function.
| NOTE |
! There should be no disc in the product when you upgrade
the software using the USB Host jack.
! When the Software update is done, check the software
details in the software update menu.
! Do not turn off the product during the software update.
It may cause the product to malfunction.
! Software updates using the USB Host jack must be
performed with a USB flash memory stick only.
By Disc
If you select Don't Upgrade, the product
cancels the upgrade.
1.
Follow Steps 1 through 7 in By USB.
Upgrade software using the broadcasting signal.
3.
Write the folder onto a disc. We recommend
a CD-R or DVD-R.
6.
By Channel
By USB
1.
Visit www.samsung.com.
3.
Enter the product's model number into the
search field, and then click Find Product.
2.
4.
5.
6.
7.
8.
9.
2.
4.
Click SUPPORT on the top right of the page.
5.
Click Get downloads in the centre of the
page below the Downloads header.
7.
Click Firmware in the centre of the page.
Click the ZIP icon in the File column on the
right side of the page.
Click OK in the pop-up that appears to
download and save the firmware file to your
PC.
Unzip the zip archive to your computer. You
should have a single folder with the same
name as the zip file.
Copy the folder to a USB flash drive.
10. Make sure no disc is inserted in the product,
and then insert the USB flash drive into the
USB port of the product.
11. In the product's menu, go to Settings >
Support > Software Update.
12. Select By USB.
| 36 English
6.
Unzip the zip archive to your computer. You
should have a single folder with the same
name as the zip file.
Finalize the disc before you remove it from
your computer.
Insert the disc into the product.
In the product's menu, go to Settings >
Support > Software update.
Select By Disc.
| NOTE |
! When the system upgrade is done, check the software
details in the software update menu.
! Do not turn off the product during the Software update.
It may cause the product malfunction.
By Downloaded
2.
3.
4.
Settings
1.
04
The By Downloaded option lets you upgrade
using a file the product downloaded earlier but
you decided not to install immediately or a file
downloaded by the product in Standby Mode.
If upgrade software has been downloaded,
you will see the software version number to
the right of By Downloaded.
Select By Downloaded, and then press the
E button.
The product displays a message asking if you
want to upgrade. Select Yes. The product
begins the upgrade.
When the update is complete, the product
turns off automatically, and then turns on.
| NOTE |
! When the system upgrade is done, check the software
details in the software update menu.
! Do not turn off the product during the software update.
It may cause the product to malfunction.
Standby Mode Upgrade
You can set the Standby Mode Upgrade function
so that the product downloads new upgrade
software when it is in Standby mode.
In Standby mode, the product is off, but its Internet
connection is active. This allows the product to
download upgrade software automatically, when
you are not using it.
1.
2.
Press the ▲▼ buttons to select Standby
Mode Upgrade, and then press the E
button.
Select the desired time.
If you select the desired time, the upgrade is
automatically performed time.
| NOTE |
! To use Standby Mode Upgrade function, your product
must be connected to the Internet.
English
37 |
Media Play
Insert a Disc to the Disc tray
1.
Place a disc gently into the disc slot with the
disc’s label facing up.
Playback starts automatically.
2.
3.
4.
Select Videos, Photos, or Music, and then
press the E button.
Depending how the contents are arranged,
you will see either folders, individual files, or
both.
Select the desired files.
Press the RETURN button to exit a folder or
to return to Home screen screen.
| NOTE |
! You must remove the USB storage device safely (by
Performing the "Safely Remove USB" function) in order to
prevent possible damage to the USB memory.
2.
If playback does not start automatically,
please refer to "Accessing the AllShare Play
Screen" on pages 38~39.
! If you insert a disc when playing a USB storage device,
the device mode changes to "DVD or CD" automatically.
Accessing the AllShare Play
Screen
| NOTE |
! In TV view mode, the 6 button will function as Timeshift
rather than its original function, playback even if there is
a disc inserted.
! In Home screen, the 6 button will function as playback
of multimedia content in the disc.
Insert a USB or Mobile Phone to
the USB port
You can play content located on a disc or USB
device through the AllShare screen
1.
2.
You can play multimedia files located on a USB or 1
mobile phone.
To play contents located on your mobile phone,
the product and mobile phone should be
2
connected with USB cable. If your mobile phone is
DLNA compatible, you can play contents without
connecting USB cable. (See pages 39~41)
1.
Connect the USB or mobile phone to the
USB port on the front panel of the product.
Settings
New device connected.
Set various functions to suit your personal preferences.
Videos
m80
Photos
Music
Smart Hub
AllShare Play
" Enter ' Return
Channel
Schedule Manager
! Safely Remove USB
| 38 English
02230H-BD-E8900A-XY-ENG.indd 38
Select AllShare Play on the Home screen,
and then press the E button.
Select the desired contents, and then select
the desired device.
AllShare Play
/ Videos /
My List
Videos
Photos
Music
Recorded TV
HDD
Disc
USB
685.85MB/926.06GB
No Disc inserted.
3
There is no device connected.
a Login
' Return
4
3
4
Contents Type : Lets you select a desired contents.
AllShare Play lets you play Videos, Photos,
or Music located in your PC or your DLNA
compatible devices, Facebook, SugarSync and
Family Story on the BD-HDD Combo with network
connection.
To use AllShare with your PC, you must install
AllShare software on your PC.
| NOTE |
! Once the connection is established, you can not only play
the video content but also transfer data between devices
using the Allshare feature.
For more information, refer to pages 46~48.
1.
2.
3.
Device Type : Lets you select a desired connected
device.
Select the connected DLNA compatible
product name, and then press the E
button.
My List
Videos
| NOTE |
Photos
! To make a playlist
Select a desired contents (Videos,Photos or Music), and
then highlight the desired files. Press the TOOLS button,
and then select Add to Playlist.
! Blu-ray/DVD/CD disk contents will not be listed in My List.
Select AllShare Play in the Home screen,
and then press the E button.
AllShare Play
Displays the coloured buttons on your remote that
you can press to access or perform functions.
! The video files played via DLNA will be listed in My List
only when the network connection has been established.
Connect the BD-HDD Combo and DLNA
compatible products to the same network .
Music
Recorded TV
1/5
/ Videos /
HDD
685.85MB/926.06GB
CANDP201012-PC: candp 201012:
Disc
Connect to AllShare device.The playback may be
unstable depending on the network connection
status.
No Disc inserted.
a Login
4.
/ Tools
' Return
Select desired file on the screen, and then
press the E button.
o HDD : You can play content that is stored in
the HDD.
o Disc : You can play content that is stored in
the disc.
o USB : You can play content that is stored in
the USB memory.
English
02230H-BD-E8900A-XY-ENG.indd 39
39 |
Media Play
2
Using the AllShare Play Function
05
1
My List : Lets you check a recently played or
updated files.
o Recently Played
Shows the list of contents viewed recently.
- If selected file is deleted or the storage device
containing selected file was removed, a message
of the selected file is unavailable will appear.
- Shows contents in the order of time, based on
the device’s system time.
- Lists up to 48 items.
o What's new
It shows a new contents.
o Playlist
You can build your own playlist grouping desired
contents.
- You can store up to 12 playlists.
- Up to 100 files can be listed into each playlist.
- If a playlist is created as music playlist, only
music files can be added to the list.
Media Play
o Camera : You can play content that is stored
in the connected camera.
o DLNA : You can play content that is stored in
the connected storage device.
o Picasa : You can play content that is stored
in the Picasa.
o SugarSync : You can play content in the
Cloud service that you are registered with.
o Family Story : You can play content that is
stored in Family Story.
o Facebook : You can play content that is
stored in the facebook.
| NOTE |
! To enable some of the services, you should have been
logged in with the respective user account for that
particular service.
Once you have logged in to Smart Hub with a registered
Samsung account, you can add an account with that
particular service by selecting Account Manager.
! Application may require to be installed through Samsung
Apps for services not appearing on the factory default.
! Some services may require logging in, and you can
manage your login account on Smart Hub.
! Some services may require creating account and
subscription to a website of corresponding service.
To download the AllShare software
To use AllShare with your PC, you must install
AllShare software on your PC.
You can download the PC software and get
detailed instructions for using AllShare from the
Samsung.com website.
1.
Go to www.samsung.com.
3.
On the Support page, enter the model
number of your product into the Model
Number field, and then press the E button.
2.
4.
Click Support at the top of the page.
On the page that appears, click Get
downloads on the left side under Downloads.
The Download Centre appears.
| 40 English
02230H-BD-E8900A-XY-ENG.indd 40
5.
6.
7.
8.
9.
On the Download Centre page, click the
Software tab.
On the software tab, click the File icon on the
right side of the AllShare line.
In the pop-up that appears, click Save File.
Find the AllShare install file on your disk, and
then double click the file.
In the pop-up that appears, click Run, and
then follow the directions that appear on your
screen.
PC
BD-HDD Combo
AllShare Play Connection
Play back
PC's files
Playing content located in your Mobile
device on the BD-HDD Combo
You can view shared files of your Mobile device to
your BD-HDD Combo.
You can get detailed instructions for using AllShare
from the Samsung.com website.
Mobile device
BD-HDD Combo
Use your mobile device to view files stored in
your computer, played by BD-HDD Combo. (Only
available with Samsung mobile devices supporting
AllShare functionality.)
You can get detailed instructions for using AllShare
from the Samsung.com website.
PC
AllShare Play
Connection
BD-HDD Combo
Play back
PC's files
Control PC's files to
BD-HDD Combo
Mobile device
| NOTE |
! Once the connection is established, you can not only play
the video content but also transfer data between devices
using the Allshare feature.
For more information, refer to pages 46~48.
Play back Mobile
device's files
English
02230H-BD-E8900A-XY-ENG.indd 41
41 |
Media Play
You can view shared files of your computer on
your BD-HDD Combo.
You can get detailed instructions for using AllShare
from the Samsung.com website.
Controlling with your mobile device
05
Playing content located in your PC on
the BD-HDD Combo
Media Play
Controlling Video Playback
You can control the playback of video content located on a Disc, USB, mobile device or PC. Depending
on the disc or contents, some of the functions described in this manual may not be available.
Buttons on the Remote Control used for Video Playback
7
8
DISC MENU
0
9
TITLE MENU
POPUP
TV MUTE
Playback related buttons
The player does not play sound in Search, Slow or
Step mode.
o To return to normal speed playback, press the
6 button.
6 button
Starts playback.
7 button
Pauses playback.
5 button
Fast Motion
Play
Slow Motion
Play
Step Motion
Play
Stops playback.
During playback, press the 3 or "
button.
Each time you press the 3 or "
button, the playback speed will change.
In pause mode, press the " button.
Each time you press the " button, the
playback speed will change.
In pause mode, press the 7 button.
Each time you press the 7 button, a
new frame appears.
Using the disc menu, title menu, popup
menu, and title list
DISC MENU
button
TITLE MENU
button
During playback, press this button to
display the Disc menu.
| NOTE |
During playback, press this button to
display the Title menu.
o If your disc has a playlist, press the
GREEN (B) button to go to the playlist.
POPUP MENU During playback, press this button to
button
display the Popup menu.
Using the Tools Menu
During playback, press the TOOLS button.
Play from the
Beginning
Title Search
During playback, press the 1 or 2
button.
Each time you press 1 or 2 button,
the disc moves to the previous or next
chapter or file.
Skip Motion
Play
| NOTE |
! If you press the 1 button after three
seconds of playback, the current
chapter or file will be replayed from
the beginning. But, if you press the
1 button within three seconds after
playback starts, the previous chapter
or file will be played.
| 42 English
02230H-BD-E8900A-XY-ENG.indd 42
! Some discs may not support this
button.
Select to return to the beginning of the
movie, and then press the E button.
If there is more than one movie on the
disc or device, select to start a different
title.
1. Select Title Search, and then press
the E button.
2. Use the ▲▼ buttons to select
a title, and then press the E
button.
Select to play the chapter of your
choice.
Chapter Search
1. Select Chapter Search, and then
press the E button.
2. Use the ▲▼ buttons to select a
chapter, and then press the E
button.
Time Search
2. Using the number buttons, enter
the time point you want to go to,
and then press the E button.
| NOTE |
Picture Mode
! You can also use the ◄► buttons
to advance or rewind the movie.
The movie advances or rewinds one
minute each time you press the ◄
► buttons.
Select to repeat a title, chapter, or
specific section.
- Off : Select to return to normal
playback.
- Title : Choose to repeat a selected
title.
- Chapter : Choose to repeat a
specific chapter.
- Repeat A-B : Choose to repeat a
specific section.
Repeat Mode
1. Press the ▲▼ buttons to select
repeat A-B, and then press the
E button.
! When you use the BD wise function,
this menu will not appear.
Audio
Subtitle
Angle
2. Press the E button at the point
where you want repeat play to start
(A). Let the movie play.
BONUSVIEW
Video
| NOTE |
Go to Videos
List
3. Press the E button at the point
where you want repeat play to stop
(B).
Full Screen
| NOTE |
! You must set point (B) at least 5
seconds of playing time after point
(A).
Select to change the full screen size.
BONUSVIEW
Audio
Information
Select to set the desired audio
language.
Select to set the desired subtitle
language.
- You can also operate this function
by pressing the SUBTITLE button on
the remote control.
Select to view a scene from another
angle. The Angle option displays the
number of angles available to view.
When a Blu-ray Disc/DVD contains
multiple angles of a particular scene,
you can change angle.
Select to set the desired bonusview
option.
Select to go to the list of videos on the
current media.
Select to view video file information.
| NOTE |
! Depending on the disc or storage device, the Tools menu
may differ. See pages 46~48 for addtional options.
! Video files with high bit rates of 20Mbps or more strain
the player's capabilities and may stop playing during
playback.
English
02230H-BD-E8900A-XY-ENG.indd 43
43 |
Media Play
1. Select Time Search, and then
press the E button.
Select to set the picture mode.
- Dynamic : Increases sharpness and
brightness.
- Standard : Choose this setting for
most viewing applications.
- Movie : The best setting for
watching movies.
- User : Lets you adjust the sharpness
and noise reduction function
respectively.
05
Select to play the movie from a
selected time point.
Media Play
Controlling Music Playback
You can control the playback of music content
located on a Disc, USB, mobile device or PC.
Buttons on the Remote Control used
for Music Playback
1
1
2
3
4
5
6
7
8
DISC MENU
TV MUTE
2
A
2
3
4
5
6
B
SMART HUB SEARCH
3
1
9
POPUP
C
D
See pages 46~48.
Go to Playlist
See pages 46~48.
Play selection
Rip
5
6
Repeating Tracks on an Audio CD
5 button : Stops a track.
Skip : During playback, press the GREEN (B) or
YELLOW (C) button to move to the previous or next
page of the playlist.
! Depending on the disc or storage device, the Tools menu
may differ. See pages 46~48 for addtional options.
You can set the product to repeat tracks on an
audio CD (CD-DA/MP3).
1.
2.
Fast Play (Audio CD (CD-DA) only)
During playback, press the 3 or " button.
Each time you press the 3 or " button, the
playback speed will change.
Title
See pages 46~48.
Folder view
Artist
Album
See pages 46~48.
See pages 46~48.
See pages 46~48.
| 44 English
02230H-BD-E8900A-XY-ENG.indd 44
Use the ▲▼ to select the repeat mode you
want - Off, One Song, or All - and then press
the E button.
/ Music /
TRACK 001
TRACK 002
TRACK 003
TRACK 004
TRACK 005
TRACK 006
TRACK 007
TRACK 008
TRACK 009
TRACK 010
6 button : Plays the currently selected track.
See pages 46~48.
During playback, use the ► button to select
in the lower right corner of the screen,
and then press the E button.
AllShare Play
7 button : Pauses a track.
View
Select to see the (Contents)
information: File size, date created, etc.
| NOTE |
NUMBER buttons : Press the number of a track.
The selected track is played.
During playback, press the TOOLS button.
The Ripping function converts CD
audio to the mp3 format and saves
the converted files on a USB device
connected to the player. See Ripping
on page 45.
4
2D 3D
Using the Tools Menu
See pages 46~48.
Information
TITLE MENU
0
Genre
1/14
Audio CD
02:38
03:17
05:21
05:34
02:54
03:44
04:07
03:42
03:15
TRACK 001
00:03 / 02:38
03:16
b! Page Move / Tools ' Return
Shuffling Tracks on an Audio CD
You can set the product to play tracks on an audio
CD (CD-DA/MP3) at random.
1.
2.
During playback, use the ► button to select
in the lower right corner of the screen,
and then press the E button.
Use the ▲▼ to set the Shuffle mode On or
Off, and then press the E button.
Creating a Playlist from a CD
3.
4.
5.
6.
Use the ▲▼ buttons to select Play selection,
and then press the E button. The Play
selection screen appears.
Use the ▲▼ buttons to select a track, and
then press the E button. A check appears
to the left of the track.
Repeat Step 3 to select and check additional
tracks.
To remove a track from the list, move to the
track, and then press the E button again.
The check on the track is removed.
When done, press the ► button to select
Play, and then press the E button. The
Music Playback screen reappears listing only
the tracks you checked. The selected tracks
play automatically.
| NOTE |
! You can create a playlist with up to 99 tracks on Audio
CDs (CD-DA).
! If you have created a playlist, Play selection is replaced by
Edit Playlist on the Tools menu.
! On the Play selection screen, you can also choose Select
All, Deselect All, and Cancel.
- Use Select All to select all tracks. This cancels your
individual track selections. When you press the
RETURN button on your remote or select 6 button,
and then press the E button, all tracks will appear
on the Music Playback screen, and the product will
begin to play all tracks from Track 001.
- Use Deselect All to deselect all selected tracks at once.
Then, select individual tracks or use Select All to select
all the tracks, and then press the RETURN button
on your remote or select 6 button, and then press
the E button. If you do not use Select All or select
individual tracks, the Playlist will not change.
- Cancel cancels any changes you made on the Play
Select screen. When you return to the Playback screen,
the Playlist will be unchanged.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Insert a USB device into the USB jack on the
rear of the product.
With the Playback screen displayed, press
the TOOLS button. The Tools menu appears.
Use the ▲▼ buttons to select Rip, and
then press the E button. The Rip screen
appears.
Use the ▲▼ buttons to select a track, and
then press the E button. A check appears
to the left of the track.
Repeat Step 3 to select and check additional
tracks.
To remove a track from the list, move to the
track, and then press the E button again.
The check on the track is removed.
When done, press the ► button to select
Rip, and then press the E button. The Rip
pop-up appears.
Press the E button to begin the ripping process.
The Ripping Completion Bar popup appears.
When ripping is complete, the "Ripping is
completed" message appears. Press the E
button.
10. Press the RETURN button to go back to the
Playback screen.
| NOTE |
! This function is not available with DTS Audio CD.
! This function may not be supported by some discs.
! This function will be encoded to the .mp3 format at 192kbps.
AMG (All Media Guide) function
You can use AMG function to display the
information of an Audio CD (CD-DA).
1.
2.
Insert an Audio CD (CD-DA).
If your disc has CD information, pop-up
screen will be displayed.
Press the E button.
The CD information will be displayed and the
first track will be played automatically.
| NOTE |
! When the product is disconnected from the network, it
may not retrieve the CD information from the Audio CD
(CD-DA).
English
02230H-BD-E8900A-XY-ENG.indd 45
45 |
Media Play
2.
With the Playback screen displayed, press
the TOOLS button. The Tools menu appears.
05
1.
Ripping
Media Play
Playing Photo Contents
You can play photo contents located on a Disc,
USB, mobile device or PC.
Using the Tools Menu
During playback, press the TOOLS button.
Go to Photos
List
Start Slide
Show
Select to go to the list of photos on the
current media.
Select to start the slide show.
Slide Show
Speed
Select to set a slide show's speed.
Background
Music On
Select to listen to music while viewing
a slide show.
Slide Show
Effect
Background
Music Setting
Picture Mode
Select to set a slide show's special
effects.
Select to set the background music
setting.
Select to set the picture settings.
- Dynamic : Choose to increase
Sharpness.
- Standard : Choose for most viewing
applications.
- Movie : This is the best setting for
watching movies.
- User : Lets you adjust the sharpness
and noise reduction function
respectively.
| NOTE |
! Depending on the disc or storage device, the Tools menu
may differ. All options may not be displayed.
! To enable the background music function, the photo file
must be in the same storage media as the music file.
However, the sound quality can be affected by the bit rate
of the MP3 file, the size of the photo, and the encoding
method.
! You can't enlarge the subtitle and PG graphic in the full
screen mode.
Using the Tools Menu when a file
is highlighted
When a file is highlighted, press the TOOLS
button.
View
Folder view
Title
Artist
| NOTE |
! When you use the BD wise function,
this menu will not appear.
Zoom
Rotate
Play selection
Login/Out
Information
| 46 English
Select to enlarge the current picture.
(Enlarge up to 4 times)
Select to rotate the picture. (This will
rotate the picture either clockwise or
counter clockwise.)
See pages 46~48
See pages 46~48.
Shows the picture information.
Album
Genre
Select to access the sort options: Artist,
Genre, Monthly, Latest Date, etc. The
sort options that appear depend on the
storage and media type.
Appears in the View function screen.
Select to display the folders on the
storage device.
Appears on the View function screen.
Select to sort all photo or video files on
a storage device by title.
Appears on the View function screen.
Select Artist to sort and then display
all music tracks on a storage device by
artist.
Appears on the View function screen.
Select Album to sort and then display
all music tracks on a storage device by
album.
Appears on the View function screen.
Select Genre to sort and then display
all music tracks on a storage device by
genre.
Monthly
Appears on the View function screen.
Select to sort and then display all photo
or video files on a storage device from
the earliest to latest date.
Appears on the View function screen.
Select to sort all photo or video files on
a storage device by the month created.
Play selection lets you select specific
music, video, and photo files to play.
It works essentially the same for all
media. The example below is for
photos.
1. On the selection screen, use the
▲▼◄► buttons to select a
photo you want to view, and and
then press the E button.
A check mark appears to the left
of the picture.
2. Repeat Step 1 for each photo you
want to view.
1. Use the ▲▼◄► buttons to
select a file, and then press the
E button.
Send
4. When done, use the ◄► buttons
to select Play, and then press
the E button. A slide show
containing the photos you selected
begins.
5. To pause the slide show, press the
E button once. To restart the
slide show, press the E button
again.
6. To stop the slide show, press the
RETURN button.
| NOTE |
! You can also move to Select All on
the right, and then press the E
button to select all tracks or files.
3. Select Send on the right side, and
then press the E button.
4. Use the ▲▼ buttons to select the
on line site you want to upload the
files or tracks to, and then press
the E button.
Login / Out
The Log In/Out function lets you log in
to your online Samsung account.
Select to create a playlist or add files
or tracks to a playlist.
3. To de-select a photo, highlight it,
and then press the E button.
Play selection
2. Repeat for each track or file you
want to upload.
Add to Playlist
1. Use the ▲▼◄► buttons to
highlight a track or file, and then
press the E button.
2. Repeat for each track or file you
want to add.
3. Select Add to Playlist on the right,
and then press the E button.
4. On the screen that appears,
perform one of the following
actions:
| NOTE |
! After the slide show begins, you can
control the slide show by pressing
the TOOLS button and displaying
the Slide Show menu. See "Using
the Tools Menu" page 46.
English
47 |
Media Play
Earliest Date
Select Send to upload selected files to
Picasa, Facebook, SugarSync or Family
Story.
To use Send, you need to establish an
account with the on-line site, and then
log in using the Log In function.
05
Latest Date
Appears on the View function screen.
Select to sort and then display all photo
or video files on a storage device from
the latest to earliest date.
Media Play
Add to Playlist
(continued)
o Select the Playlist to which you want
to add the tracks or files and then
press E button.
o Select Create New, and then press
the E button. On the keyboard
pop-up that appears, create a name
for the new playlist. Enter numbers
using the numbers on the remote.
Enter letters by using the ▲▼◄►
buttons to move the cursor, and
then pressing the E button.
When finished, move to DONE at
the bottom of the screen, and then
press the E button.
Depending on the screen you are
viewing, select Delete to erase a file
Delete (Playlist)
from erasable media (such as a USB
device) or to delete a playlist.
Select Edit Playlist to remove files or
tracks from an existing playlist. The
storage device containing the playlist
must be inserted into or attached to
the player.
Edit Playlist
1. Use the ▲▼◄► buttons to
select a file, and then press the
E button.
2. Repeat for each track or file you
want to remove.
| NOTE |
! You can also move to Select All on
the right, and then press the E
button to select all tracks or files.
3. Select Remove on the right side,
and then press the E button.
Play Current
Group
After you have sorted by Artist, Genre,
Album,Title, Latest Date, Earliest Date,
or Monthly, select a group that is the
result of the sort (for example, all
pictures taken in August), and then
select Play Current Group to play or
view the files in that group only.
| 48 English
02230H-BD-E8900A-XY-ENG.indd 48
Go to Playlist
Encoding
Information
| NOTE |
Select to go to the Playlist section of
the Main AllShare screen.
Encoding - which changes by language
or by geographical area - modifies
how the player sorts, arranges, and
presents files or tracks, displays dates,
etc. Select Encoding to change the
encoding to match your language or
geographical area.
Displays media file and content
information.
! Depending on the disc or storage device, the Tools menu
may differ. All options may not be displayed.
DTV Functions
Watching TV Channels
TV
SUBTITLE
INPUT
1
2
3
4
5
6
7
8
9
DISC MENU
0
1
Picture Mode
TITLE MENU
POPUP
TV MUTE
CH LIST
HOME
GUIDE
2
3
! This menu can not be displayed
when you use the BD wise function.
Audio Language Select to set the desired audio language.
3
1
| NOTE |
2
TV SOURCE
NUMBER buttons : To move TV channel directly,
press the channel numbers of desired TV channel.
PROG buttons : Press this button to change TV
channels.
Dual I II
Select to set the desired audio.
Signal
Information
Select to check the signal information.
Edit Favourites
INFO buttons : Press this button to display detailed
information of selected channel.
PIP
| NOTE |
! If you want to watch TV while you are playing Blu-ray
Disc/DVD/CD contents with AllShare, or Internet contents
via Smart Hub, press the EXIT button on your remote
control. With the EXIT button, you can also watch TV
directly on the Menu screen.
Using the Tools Menu
Press the TOOLS button while you are viewing a
channel.
Audio
Description
Subtitle
Select to Edit Favourites.
Select to display PIP screen.
- PIP : If you select On, you can use
PIP function.
- Channel : Select to change channels
- Size : Select to set PIP screen size.
- Position : Select to set PIP screen
position.
- Sound Select : Select one of Main
or Sub which you want to hear the
sound.
Select to add a verbal description to the
main audio to help the visually impaired.
Select to set the desired subtitle.
Select to adjust the 3D perspective
3D Perspective
3D Depth
| NOTE |
! This menu can be displayed when
convert 2D contents into 3D.
Select to adjust the 3D depth of 2D to
3D conversions.
| NOTE |
! This menu can be displayed when
convert 2D contents into 3D.
English
02230H-BD-E8900A-XY-ENG.indd 49
49 |
DTV Functions
BD
06
After Tuning is completed, you can watch TV
channel.
Select this to set the picture mode.
- Dynamic : Choose this setting to
increase Sharpness.
- Standard : Choose this setting for
most viewing applications.
- Movie : This is the best setting for
watching movies.
- User : Lets you adjust the sharpness
and noise reduction function
respectively.
DTV Functions
Using the PIP (Picture-In-Picture)
function
2.
You can see another TV channel together with the
TV Channel you were already watching.
1.
2.
3.
While you are watching a TV channel, press
the PIP button on the remote control.
The PIP screen will be displayed.
If you do not want to use PIP, press the PIP
button again while PIP is enabled.
You can make various settings for PIP using
the Tools menu. (See page 49)
| NOTE |
! When the channel list displayed, press the INFO button.
You can watch or record the selected channel.
Channel Screen
You can manage the stored channels.
1.
| NOTE |
All
! PIP and 3D effect can not be enabled in same time.
! PIP and SMART VIEW can not be enabled in same time.
1
TF1 HD
52
M6HD
800
801 FTA
804 6.10B Bad Rec...
805 6.3.5. TV 2
Data/Other
806 6.3.5. TV 3
807 6.3.5. TV 4
808 6.3.5. TV 5
809 6.7 Per sistent...
812 CANAL+
813 CANAL+FILM
814 CANAL+FILM2
815 CANAL+Sport
Press the CH LIST button on the remote
control to see all channels searched.
The Channel List will be displayed.
1
2
Channel List
All
51
TF1 HD
56
M6HD
52
M6 BOUTIQUE
800
France 2 HD
801
FTA
803
3.10.6.4 TV
802
3
NOVA
! Programme View < Ch. Mode " Watch ƒ Page
Shows the stored channels.
1
2
Navigation Help : Displays remote control buttons
available.
o YELLOW (C) : Displays the Programme information.
o ◄►: Shows the channel mode according to
channel type.
o E : Displays the selected channel.
o ▲▼ : Moves to next or previous page.
| 50 English
02230H-BD-E8900A-XY-ENG.indd 50
2
810 Aplikace MHP
811 BBC
b Delete
France 2 HD
802 NOVA
803 3.10.6.4 TV
Radio
Free
Channel List
2
51
56
TV
Editing Channels
1
In the Home screen, select Channel, and
then press the E button.
Channel
! During Recording, PIP is not supported.
1.
Select desired channel, then press the E
button.
The selected channel will be displayed.
816 CNN
i Information ƒ Page " Select / Tools ' Return
3
Shows the channel list according to channel type.
Shows the stored channels.
Navigation Help : Displays remote control buttons
available.
o GREEN (B) : Deletes selected channel.
o INFO button : Displays the Programme
information.
o ƒ : Moves to next or previous page.
o E : Selects desired channel.
o TOOLS button : Displays the Tools menu.
o RETURN button : Returns to previous menu.
Channel Status Display Icons
Icons
Operations
A channel set as Favourites.
A locked channel.
Using the Tools Menu
Lock / Unlock
Edit Channel
Number
Sorting
Channel Info
Delete
Select All
Deselect All
Select this to add the desired favourite
channel.
Select this to lock or unlock channels.
Select to edit a channel number.
If this menu does not appear, Select
Channel on the Home screen, and
then select Edit Channel Number. Set
this menu to Enable.
Select this to sort channels.
1
2
52 France 2 HD
Channel View - All
Today
812
Class News
▲
814
3
815
▼
1
2
Select this to select all channels.
5
3
4
Select this to deselect all channels.
Viewing the Guide Screen
The EPG (Electronic Programme Guide)
information is provided by broadcasters. Using
channel schedules provided by broadcasters,
you can specify channels you want to watch
in advance so that the channel automatically
changes to the selected channel at the specified
time. Channel entries may appear blank or out of
date depending on a channel status.
If you set the Country to New Zealand , Guide
screen and Functional Specification on this manual
may differ.
1.
Press the GUIDE button.
The guide screen will be displayed.
817
Coming Soon
Discovery
DiscoveryH&L
heat
No Information
9:05 - 9:35
No Information
1:00 – 2:00 1:00 – 2:00
No Information
6
5
1:00 – 2:00
1:00 – 2:00
No Information
No Information
No Information
i Information ƒ Page " Watch
6
Displays the channel screen.
Displays view mode.
Displays the Stored channels.
Displays the current date and time.
Displays the channel information.
Navigation Help : Displays remote control buttons
available.
o RED (A) : To set the programme schedule.
o YELLOW (C) : It displays channel from now to 24
hours after.
If you select YELLOW (C) button, GREEN (B)
button will be displayed. Press this to display the
list of channels before 24 hours.
o BLUE (D) : To change the Channel View.
o INFO button : Displays the Programme
information.
o ƒ : Go to previous page or next page.
o e button
- When you select a programme currently being
broadcast, you can watch the selected channel
in the full screen.
- When you select a programme scheduled to
broadcast, you can set the Schedule Viewing
or Schedule Recording. Press the ◄► button
to select the Schedule Viewing or Schedule
Recording, then press the e button again.
The Timer icon appears on the guide screen.
English
02230H-BD-E8900A-XY-ENG.indd 51
4
No Information
a Sche. Mgr ! +24 Hours d Ch. Mode
Select this to check the channel
information of selected or checked
channel.
Select this to delete the channel.
813
9:20 Fri 11 Jun
Des jours et des vies
51 |
DTV Functions
Edit Favourites
Guide
06
When the channel displayed, press the TOOLS
buttons.
o Guide Screen
DTV Functions
Schedule Manager
1
You can reserve the desired TV programmes using
this menu.
Make sure that clock must be set before operating
this function. (See page 27)
1.
2.
3.
4.
Select Schedule Manager on the Home
screen, and then press the E button.
Press the RED (A) button.
2
3
Select Schedule Viewing or Schedule
Recording, and then press the E button.
Fill the input items, and then press the E
button.
| NOTE |
4
! In the guide view, Schedule Viewing and Schedule
Recording schedules are not displayed.
Using the Teletext Service
5
If DTV programme supports teletext signal, you
can use teletext service. For Teletext information
is displayed correctly, channel reception must be
stable. Otherwise, information may be missing or
some pages may not be displayed.
1.
2.
Press TTX/MIX button while you are viewing
a TV channel.
6
7
8
9
By pressing the TTX/MIX button repeatedly,
you can change or exit the teletext mode.
0
TV MUTE
TV SOURCE
1
CH LIST
HOME
GUIDE
2
3
4
5
6
7
8
9
0
!
A
B
C
DIGITAL
SUBTITLE
SMART HUB SEARCH
SOCIAL
REC
| 52 English
02230H-BD-E8900A-XY-ENG.indd 52
D
2D 3D
INPUT
REC PAUSE
!
8 : Stores the Teletext pages.
4 : Displays the teletext on the upper half of the
screen in double-size. To move the text to the lower
half of the screen, press it again. For normal display,
press it once again.
9 : Holds the display at the current page, in the
case that there are several secondary pages that
follow automaticially. To undo, press it again.
Colour buttons (red, green, yellow, blue) : If the
FASTEXT system is used by the broadcasting
company, the different topics on a Teletext page are
colour-coded and can be selected by pressing the
coloured buttons. Press the colour corresponding to
the topic of your choice. A new colourcoded page
is displayed. Items can be selected in the same
way. To display the previous or next page, press the
corresponding coloured button.
1 : Displays the available sub-page.
2 : Displays the next Teletext page.
3 : Displays the previous Teletext page.
6 : Displays the index (contents) page at any time
while you are viewing Teletext.
0 : Selects the Teletext mode (LIST/ FLOF). If
pressed during LIST mode, switches the mode to
List savemode. In List save mode, you can save a
Teletext page into a list using the 8(store) button.
5 : Displays the hidden text (answers to quiz
games, for example). To display the normal screen,
press it again.
7 : Shrinks the Teletext display to overlap with the
current broadcast.
Typical Teletext page
B
C
06
A
D
DTV Functions
E
F
Part
Contents
A
Selected page number.
C
Current page number or search indications.
B
D
E
F
Broadcasting channel identity.
Date and time.
Text.
Status information. FASTEXT information.
| NOTE |
! Teletext TTX/MIX control is available only when the DTV
programme support teletext signal.
English
02230H-BD-E8900A-XY-ENG.indd 53
53 |
Advanced Function
Recording
! Display of HDD Capacity
Before recording
o Please check the default recording device
and available storage size in storage device
for recording. (please refer to “Storage Device
Manager" on page 28.)
o At least 100MB of free space is required for
recording.
o Recording will stop if the storage's free space
becomes less than 50MB.
Checking Available Storage Size
To check the available storage size in Recorded
TV, Select AllShare Play>Recorded TV> HDD in
the Home screen.
Highlight the HDD, and then press the INFO
button on the remote control.
| NOTE |
! Notes on HDD capacity
- This product reserves HDD capacity internally as
described below, for function implementations and this
reserved portion is not used for recording.
* Time Shift : 22GB
* Functional Purpose : 5GB
- The displayed capacity on OSD which shows
approximated available capacity for recording is shown
below, calculated based on shipped status.
Model Name
BD-E8900A
BD-E8500A
HDD Vendor
Specification
Available Size
500GB
438GB
1TB
| 54 English
02230H-BD-E8900A-XY-ENG.indd 54
904GB
- The Capacity of the HDD manufacturer is calculated
assuming that 1KB = 1,000 Bytes. However, the
operating system of the product calculates the capacity
of HDD capacity assuming that 1KB=1,024 Bytes,and
therefore detected capacity by this product is about
93% of HDD Manufacturer representation. E.g. for a
1TB(1000GB) HDD, this product detect as 931.3 GB.
| CAUTION |
! It is recommended to use recorded or edited files with the
product for private purposes only.
Recording the current TV channel you
are watching
1.
2.
3.
4.
Press the PROG or number buttons to select
a TV Channel you want to record.
Press the REC button.
If you want to adjust length of the recording,
press the E button.
Select the desired length of the recording,
then press the E button.
To pause recording
1.
2.
Press the REC PAUSE button to pause a
recording in progress.
Press the REC button to resume recording.
To stop recording
Press the 5 button to stop a recording in
progress.
Playback control during recording
During recording a TV channel, you can search
scene or move to the beginning point of recording
without influence on the recording through
Timeshift function.
For more information about Timeshift function,
please refer to the Timeshift function.(See pages
55~57)
1.
4.
5.
6.
7.
2 button : Jump to the same scene with
Live TV.
◄ button : Jump to - 10 sec from current
position.
► button : Jump to + 10 sec from current
position.
7 button : Pause the scene while keeping
recording progress.
5 button : If you are watching the past
scene, the playback point will jump to the
same scene with Live TV. If you are watching
same scene with Live TV, recording will be
stopped.
While a TV programme is being recorded, you can
also watch TV channels.
During the recording, press the PROG or number
buttons to change the channel you want to watch.
| NOTE |
! During Recording, DUAL VIEW is not supported
! Recorded files of less than 10 seconds are not saved.
Simultaneous Recording
Simultaneous Recording of Two TV
Channels
2.
1.
1 button : Return to the beginning point of
recording.
Watching other channels during
Recording a TV channel
1.
You can watch yet another channel while
recording two TV channels at the same time.
While a TV channel is being recorded, move
to other TV channel that you want to record.
2.
Press the CH LIST button to check which TV
channel is possible to watch.
White coloured TV Channel in Channel List
is what you can move without stopping the
recordings already started.
Press the E button to watch the possible
TV Channel.
To watch a channel that is not displayed
in white, you need to stop at least one of
currently recording.
To stop recording
!
If you are watching a TV channel which is
under recording
Press the 5 button.
!
If you are watching a TV channel which is
not under recording
Select a TV channel what you want to stop the
recording, and the press the 5 button.
Simultaneous Operation
You can play a disc or enjoy other function during
recording.
1.
Press the HOME button, and then select the
Smart Hub or AllShare function. But, you can
not select the settings menu unless stop the
recording.
Timeshift function
You can pause a live TV or start watching the TV
programme from the beginning point you started
Timeshift function.
Press the REC Button.
The recording will be started.
English
02230H-BD-E8900A-XY-ENG.indd 55
55 |
Advanced Function
3.
Watching different TV channels that is not
under recording
07
2.
3" buttons : Search the desired scene.
Each time this button is pressed, playback
speed will change.
)1 )2 )3
)4 )5 )6 )7
(1 (2 (3
(4 (5 (6 (7
Advanced Function
Start Timeshift with PLAY button
1.
2.
When you are watching a TV channel, press
the 6 button.
The Timeshift function starts and the
Timeshift bar will appear. Live TV is displayed
on the left side of Timeshift bar.
Start Timeshift with PAUSE button
1.
2.
When you are watching a TV channel, press
the 7 button.
The image of TV programme will be paused,
and then Timeshift bar will appear.
7 Pause is displayed on the left side of
Timeshift bar.
- Timeshift automatically stops when selected another
menu in the Home menu. (Stops Timeshift and history
functions that were operating.)
- Returning to a Digital TV channel will automatically
resumes Timeshift, if not accessed any other menu
item of the Home menu.
! For Timeshift function, 22GB of the internal HDD is
reserved.
o Timeshift Screen
1
DTV
All
France 2 HD
52
Timeshift information
Stereo
No title
+
2 3
18:12 Sat 15 Nov
Multi Movie/Drama
+00:00:06/
00:00:34
4
You can see current information about Timeshift
function.
1.
2.
Press the E button on your remote while
Timeshift function is enabled.
Timeshift bar appears as below.
| NOTE |
! The Timeshift settings are sustained even when you
switch to another channel in Timeshift operation.
In this case, Timeshift of former channel is supported as
history function. (The Timeshift of former channel is still
available)
! If Timeshift is started with Play or Pause key, the Timeshift
is sustained until the Stop button is pressed. In case
when the Timeshift operation becomes not available (such
as switching to another application, an analogue channel
or changing the input source), Timeshift stops without a
notification and will resume automatically as soon as the
source is switched to Digital TV.
- The history function supports only for records of
switching within channels of Digital TV source.
- If switched to an analog channel, history and Timeshift
will stop functioning automatically.
1
2
3
4
Shows current playback point.
Shows recorded time by Timeshift function.
Shows progress bar.
Playback control button during Timeshift
function is enabled
1.
2.
3.
| 56 English
Mode Display : Shows current status of Timeshift
function.
3" buttons : Search the desired scene.
Each time this button is pressed, playback
speed will change.
)1 )2 )3
)4 )5 )6 )7
(1 (2 (3
(4 (5 (6 (7
1 button : return to the beginning of
Timeshift.
2 button : Shows same scene with Live TV.
4.
7.
7 button : Pause the scene while keeping
Timeshift operation.
5 button : If you are watching the past
scene, playback point will jump to the same
scene with Live TV. If you are watching the
same scene with Live TV, the Timeshift
function will be stopped.
To stop Timeshift
1.
2.
3.
4.
5.
2.
3.
4.
2.
3.
In the Recorded TV screen, select the
desired title you want to edit.
Press the TOOLS button.
Select the Edit, then press the E button.
Splitting a Section of a Title (Divide into
two)
Follow Steps 1 through 3 in the ‘Edit the Recorded
Title’.
If Timeshift bar is not in pause or past mode,
press 5 button.
The message "Do you want to stop the
Timeshift?" will appear.
AllShare Play Recorded TV
Part 1
Select Yes then press the E button.
Select AllShare Play on the Home screen,
then press the E button.
Select the Recorded TV, then press the E
button.
The Recorded TV List will be displayed.
Select
Part 2
00:00:00
00:00:33 / 00:08:21
+
If the Timeshift bar is in pause or past mode,
Timeshift mode will be changed into Live TV
when you press 5 button first time.
Press 5 button again, then same message
with above image appears.
| Split | No title
00:00:00
Select OK button and press E button to
stop Timeshift.
Playing the Recorded Title
1.
1.
Playback Controls
Split
Return
Scene Search < Jump > Move " Enter
1.
Select the Split, then press the E button.
3.
Press the E button to select Split.
2.
4.
Using the playback-related buttons, move to
a point for splitting and then press the E
button.
Select OK, then press the E button.
The split title is divided into two, and the
following titles will be shifted down by one.
Select the desired device, then press the E
button.
Select the title you want to play, then press
the E button.
The selected title will be played back.
English
57 |
Advanced Function
6.
► button : Jump to + 10 sec from current
position.
Editing the Recorded Title
07
5.
◄ button : Jump to - 10 sec from current
position.
Advanced Function
Splitting a Section of a Title (Partial
Delete)
Follow Steps 1 through 3 in the ‘Edit the Recorded
Title’.
1.
Select the Partial Delete, then press the E
button.
AllShare Play Recorded TV
00:00:00
Part 2
00:00:00
00:00:33 / 00:08:21
+
Playback Controls
2.
3.
4.
5.
Start
End
Delete
Return
Scene Search < Jump > Move " Enter
Press the E button at the starting point.
The image and starting point time is displayed
in the section deletion starting point window.
o Select the start and end points of the
section you want to delete using the
playback related buttons.
Press the E button at the end point.
The image and end point time is displayed in
the Section deletion ending point window.
Press the E button to select Delete.
Select OK, then press the E button.
| NOTE |
! The minimum length of delete section should be longer
than 10 seconds.
Copying Videos, Music or Photos
Music
3.
HDD/DISC/
AllShare
# USB
Photos
Videos
Supported
Supported
Supported
DISC/USB/ HDD/DISC/
AllShare
USB
# HDD
# AllShare
Supported
Supported
Supported
Supported
Supported
| 58 English
02230H-BD-E8900A-XY-ENG.indd 58
Supported
Press the HOME button.
The home screen will be displayed.
In Stop mode, connect the USB storage
device to the USB port on the front panel of
the product.
4.
Select the desired contents type, then press
the E button.
Select the desired contents.
6.
Select the Send, then press the E button.
5.
7.
8.
Press the TOOLS button.
Press the E button to check desired files.
Select the Send, then press the E button.
To cancel the copying in progress, press the
E button.
3D Functions
3D Converter
This function can convert the 2D output of 2D
contents into 3D.
1.
2.
3.
Copy
Contents
1.
2.
| Partial Delete | No title
Part 1
o Disc (CD-DA/CD-R/CD-RW, DVD±R(Finalise)/
DVD+RW/DVD-RW(Finalise)) " HDD or USB
o PTP USB is not available when you copy to
USB.
o The broadcast signal can be recorded on HDD
but copy feature is not supported.
Connect this product to a TV that supports
3D using an HDMI cable.
When you play 2D contents, press the
2D 3D button on the remote control to
convert 2D into 3D contents.
You can toggle between 2D and 3D by
pressing the 2D 3D button repeatedly.
If you are playing 3D contents in the 3D
mode, you cannot use this function.
| NOTE |
Viewing DTV with the 3D effect
You can experience 3D effect with all live TV
programme and recorded TV programme.
! 2D content is converted into the following 3D formats:
- 1080p 24fps : Output to 1080p 24 fps 3D.
- Others : Output to 720p 3D.
- Photo files : Output to 720p 3D.
! 2D content that the product can convert to 3D:
- 2D content that supports 3D conversion
- Smart Hub content, DVD Video, BD-ROM, Video files,
photo files, DTV programme, and recorded DTV
programme.
! When you use the 3D converter, the BONUSVIEW function
is not available.
(Depending on the disc, a black outline appears.)
! Some viewers may experience discomfort while viewing
3D contents such as dizziness, nausea, and headaches.
Adjusting the 3D Depth
The 3D Depth function lets you adjust the 3D
depth of 2D to 3D conversions. Values range from
1 to 10. The higher the number, the deeper the 3D
depth.
1.
2.
3.
When you are viewing converted 3D
contents, press the TOOLS button.
Press the ▲▼ buttons to select 3D Depth,
and then press the E button.
During watching the TV programme or
playing recorded TV programme, press the
2D 3D button on your remote control. The
3D menu will appear.
o 2D 3D : Changes a 2D image to 3D.
o Side by Side : Displays two images next to
each other.
2.
3.
o Top and Bottom : Displays one image
above another.
Press the ◄► buttons to select the desired
3D mode, then press the E button.
If you press the 2D 3D button once more
during 3D viewing, displayed image will be
changed into 2D mode.
| NOTE |
! If you change TV channel during watching DTV in 3D
mode of Side by Side mode, displayed image will be
changed into 2D mode automatically.
! When 3D effect of Side by Side mode is enabled, you can
not adjust 3D mode.
! If TV programme is not support Side by Side, Top and
Bottom mode or Auto Detection function, 3D menu
selection OSD is not appear.
! 3D Effect and SMART VIEW can not be enabled in same
time.
Adjust the 3D Depth using the ◄► buttons.
English
02230H-BD-E8900A-XY-ENG.indd 59
59 |
Advanced Function
1.
07
! You can’t convert 2D contents into 3D or use the 2D 3D
button In the following cases:
- When the product is not connected with an HDMI cable
- When the connected TV does not support 3D
- When you are playing 3D contents (disc, file).
Network Services
You can enjoy various network services such as
Smart Hub or BD-LIVE by connecting the product
to your network.
Smart Hub at a Glance
1
To use network services, you must first:
1.
2.
0
9
Using Smart Hub
Using Smart Hub, you can download movies,
videos, and music from the Internet, and access
various for pay or free-of-charge applications
and view them on your TV. Application content
includes news, sports, weather forecasts, stock
market quotes, maps, photos, and games.
For instructions that explain how to use Smart
Hub, follow these steps:
If the home page is updated or revised, the
content mentioned in the user manual may differ
from the actual menus.
1.
Go to www.samsung.com.
3.
On the Support page, enter the model
number of your product into the Model
Number field, and then press Enter button.
2.
4.
5.
6.
1
2
3
4
5
6
On the Download Centre page, click the
Manuals tab.
On the Manuals tab, click the file icon to the
right of Smart Hub Users Manual. The manual
downloads.
7
| NOTE |
! The web location of the Smart Hub manual is subject to
change without notice.
| 60 English
Samsung Apps
Your Video
Family Story
5
Fitness
Kids
6
Contents 1
Contents 2
Contents 3
Contents 4
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
7
a Login b Wallpaper / Tools ' Return
Click Support at the top of the page.
On the page that appears, click Get
downloads on the left side under Downloads.
The Download Centre appears.
34
Search
Connect the product to the network.
(See page 20)
Configure the network settings.
(See pages 31~33)
2
8
8
Your Video : Provides recommendations for videos
based on your tastes.
Search : Provides an integrated search of your
video providers and connected AllShare devices.
Recommended : Displays recommended contents
managed by Samsung.
Commercial : Displays the Smart Hub Guide, an
introduction to the product, and new application
introductions.
Family Story : Effortless way to access family
content.
o Provides access to family photos, messages, and
events, anytime and anywhere.
Fitness : Gateway to the Unified Self-Care Service.
o Presents fitness videos from various content
partners with feedback on calories burned after
every workout.
Kids : Kids service gives kids an easy and safe way
to enjoy their favorite content.
o Provides a wide variety of fun and safe content
for children.
Navigation Help : Displays the remote control
buttons you can use to navigate in Smart Hub.
o RED (A) : To log in to Smart Hub.
o GREEN (B) : To display the background screen.
o Tools : To display the settings window.
o Return : To return to the previous menu.
Web Browser at a Glance
1
Samsung Apps : Open Samsung Apps to download
various for pay or free-of-charge application
services.
http://www.google.com/
Network Services
0
08
My Applications : Displays your personal gallery
of applications which you can add to, modify, and
delete.
9
Using the Web Browser
You can access the internet using the Web
Browser application which is installed in the Smart
Hub screen by default.
1.
2.
Google Search
b Control Panel ! Pointer Browsing d PIP / Tools e Exit
Select Smart Hub on the Home screen, and
then press the E button.
Select the Web Browser application in Smart
Hub, and then press the E button.
| NOTE |
! To change PIP channels, press the PROG button on the
remote control.
The PIP CH+ and PIP CH- buttons on the remote control
does not operate.
! When you run the Web Browser with the product connected
by HDMI to a BD Wise compatible TV - and BD Wise is on
- the browser is maximized to fill the screen and the TV's
resolution is set to the optimal resolution automatically.
! The Web Browser is not compatible with Java
applications.
! If you attempt to download a file, and the file can not be
saved, an error message will appear.
! The playback of Flash videos is not supported.
! E-commerce, for purchasing proudcts online, is not
supported.
! ActiveX is not supported.
I’m Feeling Lucky
1
2
Control Panel : Displays the various Web Browser
functions.
o : Moves to the previous page.
o : Moves to the last page before going back.
o : Reloads the current page so that it is
refreshed on the screen.
o : Moves to the Home screen of the Web
Browser.
o : Allows you to zoom in or out of the screen at
various percentages.
o : Allows you to bookmark specific pages so
that you can move to them easily.
o : Allows you to view the history of your visited
pages by date, name, or frequency.
o http://www.google.com/
: Allows you to enter a
page address manually or select a page from the
visited page list to move to that page.
o
: Allows you to switch easily between
multiple, currently open Web Browser windows.
o : Allows you to search for information by
entering words.
o : Lets you share the current site with your
family group by sending a message.
o : Allows you to configure all settings for using
the Web Browser.
English
61 |
Network Services
Navigation Help : Displays the remote control
buttons you can use to navigate in Web Browser.
o GREEN (B) : To display the Control Panel.
o YELLOW (C) : To switch the pointer.
o BLUE (D) : To use the PIP function.
o Tools : To display Tools window.
o Exit : To exit the Web Browser.
2
BD-LIVE™
Once the product is connected to your network,
you can enjoy various movie-related service
contents available on BD-LIVE compliant discs.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Attach a USB memory stick to the USB jack
on the front of the product, and then check
its remaining memory. The memory device
must have at least 1GB of free space to
accommodate the BD-LIVE services.
Select Settings on the Home screen, and
then press the E button.
Select Network, and then press the E
button.
Select BD Live Settings, and then press the
E button.
Select Delete BD Data, and then press the
E button.
Select Select Device, and then press the
E button.
Select USB, and then press the E button.
Insert a Blu-ray Disc that supports BD-LIVE.
Select an item from the list of BD-LIVE service
contents provided by the disc manufacturer.
| NOTE |
! The way you use BD-LIVE and the provided contents may
differ, depending on the disc manufacturer.
| 62 English
Samsung Smart View
This function is available via Samsung Smart View
app for Samsung BD-HDD Combo.
To Enjoy Smart View, your BD-HDD Combo and
mobile device should be connected via Wi-Fi.
The connection can be established as follows
1.
2.
3.
BD-HDD Combo and mobile device are
Connected to the same wireless Router
Mobile device is connected to BD-HDD
Combo directly via Soft AP function in
Network Menu.
If your mobile device supports Wi-Fi Direct, it
can connect to BD-HDD Combo directly via
Wi-Fi Direct function in Network Menu.
Dual View
Enjoy TV channel right from your mobile device
that's connected to Samsung BD-HDD Combo.
You can view the same channel of TV, or a
different channel than selected on TV, on your
mobile device at the same time.
| NOTE |
! Available only if the mobile device supports this function.
! Samsung Smart View is a dedicated application to
Samsung smart phone/tablet. If you have a Samsung
smart phone/tablet supporting this feature (Smart View),
you can download Smart View from Android Market
or Samsung Apps and install it on your device. (The
compatibility of mobile devices or mobile platform is
subject to change in the future.)
Appendix
Compliance and Compatibility Notice
63 |
Appendix
English
09
NOT ALL discs are compatible
o Subject to the restrictions described below and those noted throughout this Manual, including the Disc
Type and Characteristics section of this user manual, disc types that can be played are: pre-recorded
commercial BD-ROM, DVD-VIDEO, and Audio CD (CD-DA); BD-RE/R, DVD-RW/-R; and CD-RW/R.
o Discs other than the above cannot and/or is not intended to be played by this product. And some of
the above discs may not play due to one or more reasons provided below.
o Samsung cannot assure that this product will play every disc bearing the BD-ROM, BD-RE/R, DVDVIDEO, DVD-RW/-R, DVD+RW/+R and CD-RW/R logos, and this product may not respond to all
operating commands or operate all features of every disc. These and other disc compatibility and
product operation issues with new and existing format discs are possible because:
- Blu-ray is a new and evolving format and this product may not operate all features of Blu-ray Discs
because some features may be optional, additional features may have been added to the Blu-ray
Disc format after the production of this product, and certain available features may be subject to
delayed availability;
- not all new and existing disc format versions are supported by this product;
- new and existing disc formats may be revised, changed, updated, improved and/or supplemented;
- some discs are produced in a manner that allows specific or limited operation and feature during
playback;
- some features may be optional, additional features may have been added after the production of this
product or certain available features may be subject to delayed availability;
- some discs bearing the BD-ROM, BD-RE/R, DVD-VIDEO, DVD-RW/-R, DVD+RW/+R and CD-RW/R
logos may still be non-standardized discs;
- some discs may not be played depending on their physical state or recording conditions;
- problems and errors can occur during the creation of Blu-ray Disc, DVD software and/or the
manufacture of discs;
- this product operates differently than a standard DVD product or other AV equipment; and/or
- for reasons noted throughout this user manual and for other reason(s) discovered and posted by
SAMSUNG customer care centre.
o If you encounter disc compatibility or product operation problems, please contact SAMSUNG customer
care centre.
You may also contact SAMSUNG customer care centre for possible updates on this product.
o For additional information on playback restrictions and disc compatibility, refer to the Precautions,
Before Reading the user manual, Disc Types and Characteristics, and Before Playing sections of this
user manual.
Appendix
Copy Protection
o Because AACS (Advanced Access Content System) is approved as content protection system for Bluray Disc format, similar to use of CSS (Content Scramble System) for DVD format, certain restrictions
are imposed on playback, analogue signal output, etc., of AACS protected contents.
The operation of this product and restrictions on this product may vary depending on your time of
purchase as those restrictions may be adopted and/or changed by AACS after the production of this
product. Furthermore, BD-ROM Mark and BD+ are additionally used as content protection system for
Blu-ray Disc format, which imposes certain restrictions including playback restrictions for BD-ROM
Mark and/or BD+ protected contents. To obtain additional information on AACS, BD-ROM Mark, BD+,
or this product, please contact SAMSUNG customer care centre.
o Many Blu-ray Disc/DVDs are encoded with copy protection. Because of this, you should only connect
your Product directly to your TV, not to a VCR. Connecting to a VCR results in a distorted picture from
copy-protected Blu-ray Disc/DVDs.
o This item incorporates copy protection technology that is protected by U.S. patents and other
intellectual property rights of Rovi Corporation. Reverse engineering and disassembly are prohibited.
o Under the U.S. Copyright laws and Copyright laws of other countries, unauthorized recording, use,
display, distribution, or revision of television programmes, videotapes, Blu-ray Discs, DVDs, and other
materials may subject you to civil and/or criminal liability.
o Cinavia Notice : This product uses Cinavia technology to limit the use of unauthorized copies of
some commercially-produced film and videos and their soundtracks. When a prohibited use of
an unauthorized copy is detected, a message will be displayed and playback or copying will be
interrupted.
More information about Cinavia technology is provided at the Cinavia Online Consumer Information
Centre at http://www.cinavia.com. To request additional information about Cinavia by mail, send a
postcard with your mailing address to: Cinavia Consumer Information Centre, P.O. Box 86851, San
Diego, CA, 92138, USA.
This product incorporates proprietary technology under licence from Verance Corporation and is
protected by U.S. Patent 7,369,677 and other U.S. and worldwide patents issued and pending as well
as copyright and trade secret protection for certain aspects of such technology. Cinavia is a trademark
of Verance Corporation. Copyright 2004-2010 Verance Corporation. All rights reserved by Verance.
Reverse engineering or disassembly is prohibited.
Network Service Disclaimer
All content and services accessible through this device belong to third parties and are protected by
copyright, patent, trademark and/or other intellectual property laws. Such content and services are
provided solely for your personal noncommercial use. You may not use any content or services in a
manner that has not been authorized by the content owner or service provider. Without limiting the
foregoing, unless expressly authorized by the applicable content owner or service provider, you may
not modify, copy, republish, upload, post, transmit, translate, sell, create derivative works, exploit, or
distribute in any manner or medium any content or services displayed through this device.
| 64 English
o Dolby and the double-D symbol are registered trademarks of Dolby Laboratories.
o Manufactured under licence under U.S. Patent Nos: 5,956,674; 5,974,380;
6,226,616; 6,487,535; 7,212,872; 7,333,929; 7,392,195; 7,272,567 & other U.S.
and worldwide patents issued & pending. DTS-HD, the Symbol, & DTS-HD and the
Symbol together are registered trademarks & DTS-HD Master Audio is a trademark of
DTS, Inc. Product includes software. © DTS, Inc. All Rights Reserved.
o DivX
- ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a
subsidiary of Rovi Corporation. This is an official DivX Certified® device that plays DivX video. Visit
divx.com for more information and software tools to convert your files into DivX videos.
- ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to play
purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate the
DivX VOD section in your device setup menu. Go to vod.divx.com for more information on how to
complete your registration.
English
65 |
Appendix
Licence
09
THIRD PARTY CONTENT AND SERVICES ARE PROVIDED "AS IS." SAMSUNG DOES NOT WARRANT
CONTENT OR SERVICES SO PROVIDED, EITHER EXPRESSLY OR IMPLIEDLY, FOR ANY PURPOSE.
SAMSUNG EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED
TO, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. SAMSUNG
DOES NOT GUARANTEE THE ACCURACY, VALIDITY, TIMELINESS, LEGALITY, OR COMPLETENESS
OF ANY CONTENT OR SERVICE MADE AVAILABLE THROUGH THIS DEVICE AND UNDER NO
CIRCUMSTANCES, INCLUDING NEGLIGENCE, SHALL SAMSUNG BE LIABLE, WHETHER IN
CONTRACT OR TORT, FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL
DAMAGES, ATTORNEY FEES, EXPENSES, OR ANY OTHER DAMAGES ARISING OUT OF, OR IN
CONNECTION WITH, ANY INFORMATION CONTAINED IN, OR AS A RESULT OF THE USE OF ANY
CONTENT OR SERVICE BY YOU OR ANY THIRD PARTY, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES.
Third party services may be terminated or interrupted at any time, and Samsung makes no representation
or warranty that any content or service will remain available for any period of time. Content and services
are transmitted by third parties by means of networks and transmission facilities over which Samsung
has no control. Without limiting the generality of this disclaimer, Samsung expressly disclaims any
responsibility or liability for any interruption or suspension of any content or service made available
through this device.
Samsung is neither responsible nor liable for customer service related to the content and services.
Any question or request for service relating to the content or services should be made directly to the
respective content and service providers.
Samsung is neither responsible nor liable for customer service related to the content and services.
Any question or request for service relating to the content or services should be made directly to the
respective content and service providers.
Appendix
- DivX Certified® to play DivX® video up to HD 1080p, including premium content.
DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or its subsidiaries
and are used under license.
Covered by one or more of the following U.S. patents : 7,295,673; 7,460,668; 7,515,710; 7,519,274
o The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI
Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.
o Oracle and Java are registered trademarks of Oracle and/or its affiliates. Other names
may be trademarks of their respective owners
o Rovi Flow-Down Licence Terms (Terms of Use)
- This application incorporates software and technology of Rovi Corporation ("Rovi"). The Rovi software
and technology (collectively, the "Rovi Technology") allows End Users to access music-related data
("Rovi Data") over the Internet and otherwise from proprietary Rovi databases (the "Rovi Databases")
located on Rovi servers (the "Rovi Servers") and to perform other functions. You may access and use
Rovi Data only by means of the intended End User functions of this application software.
- You agree that you will use the Rovi Data, the Rovi Technology, and the Rovi Servers for your own
personal non-commercial use only. You agree not to assign, copy, transfer or transmit the Rovi
Data to any third party. You agree not to use or exploit Rovi Data, the Rovi Technology, the Rovi
Databases, or the Rovi Servers, except as expressly permitted herein.
- You agree that your non-exclusive licence to access the Rovi Databases and to use the Rovi Data,
the Rovi Technology, and the Rovi Servers will terminate if you violate these restrictions. If your
licence terminates, you agree to cease any and all use of the Rovi Data, the Rovi Technology, and the
Rovi Servers. Rovi reserves all rights in Rovi Data, the Rovi Technology, and Rovi Servers, including
all ownership rights. You agree that Rovi may enforce its rights under this Agreement against you
directly in its own name.
- Rovi reserves the right to delete data from the Rovi Databases or to change data categories for any
cause that Rovi deems sufficient. No warranty is made that the Rovi Technology or Rovi Servers are
error-free or that functioning of Rovi Technology or Rovi Servers will be uninterrupted. Rovi is not
obligated to provide you with any new enhanced or additional data types or categories that Rovi may
choose to provide in the future and is free to discontinue its online services at any time.
- The data you submit to use will not be personal data or personally identifiable data, but rather
only data respecting music albums and associated data that does not appear in the Rovi Lookup
Database. You certify that to the best of its knowledge the album to which the submitted data
corresponds is commercially available and that you End User are lawfully permitted to submit the
data.
| 66 English
o Blu-ray Disc™, Blu-ray™, and the logos are trademarks of Blu-ray Disc Association.
English
67 |
Appendix
o Open Source Licence Notice
- In the case of using open source software, Open Source Licences are available on the product
menu.
09
- To the extent that you, the End User, provide any information or original works of authorship to be
added to Rovi Databases, you represent and warrant that you are the sole author of such work(s)
and further hereby assign to Rovi all rights of copyright therein, including the right to register the
copyright in such work(s) as part of the Rovi Database.
- THE ROVITECHNOLOGY AND EACH ITEM OF ROVI DATA ARE LICENCED TO YOU "AS IS." ROVI
MAKES NO REPRESENTATIONS OR WARRANTIES, EXPRESS OR IMPLIED, REGARDING THE
ACCURACY OF ANY ROVI DATA ON THE ROVI SERVERS. ROVI DISCLAIMS ALL WARRANTIES
EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE AND NON-INFRINGEMENT.
ROVI DOES NOT WARRANT THE RESULTS THAT WILL BE OBTAINED BY YOUR USE OF THE
ROVI TECHNOLOGY OR ANY ROVI SERVER. IN NO CASE WILL ROVI BE LIABLE TO YOU OR
ANY THIRD PARTY FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES OR FOR ANY
LOST PROFITS OR LOST REVENUES RESULTING FROM YOUR USE OF ROVI DATA, THE ROVI
TECHNOLOGY OR OTHERWISE.
Appendix
Additional Information
Note
3D Settings
o For some 3D discs, to stop a movie during 3D playback, press the 5 button once. The movie
stops and the 3D mode option is de-activated.
To change a 3D option selection when you are playing a 3D movie, press the 5 button once.
The Blu-ray menu appears. Press the 5 button again, then select 3D Settings in the Blu-ray
menu.
o Depending on the content and the position of the picture on your TV screen, you may see vertical
black bars on the left side, right side, or both sides.
TV Aspect Ratio
o Depending on the disc type, some aspect ratios may not be available.
o If you select an aspect ratio and option which is different than the aspect ratio of your TV screen,
then the picture might appear to be distorted.
o If you select the 16:9 Original, your TV may display 4:3 Pillarbox (black bars on sides of picture).
BD Wise (Samsung Products only)
Settings
o When BD Wise is on, the Resolution setting automatically defaults to BD Wise and BD Wise
appears in the Resolution menu.
o If the product is connected to a device that does not support BD Wise, you can not use the BD
Wise function.
o For proper operation of BD Wise, set the BD Wise menu of both the product and the TV to On.
Digital Output
o Be sure to select the correct Digital Output or you will hear no sound or just loud noise.
o If the HDMI device (AV receiver, TV) is not compatible with compressed formats (Dolby Digital,
DTS), the audio signal outputs as PCM.
o Regular DVDs do not have BONUSVIEW audio and Navigation Sound Effects.
PCM Downsampling
o Even when PCM Downsampling is set to Off, some discs will only output downsampled audio
through the optical digital outputs.
o HDMI
- If your TV is not compatible with compressed multi-channel formats (Dolby Digital, DTS), the
product may output PCM 2ch downmixed audio even though you selected Bitstream (either
Reencoded or Unprocessed) in the setup menu.
- If your TV is not compatible with PCM sampling rates over 48kHz, the product may output
48kHz.
| 68 English
BD-LIVE Internet Connection
Settings
o In the external memory mode, disc playback may be stopped if you disconnect the USB device in
the middle of playback.
o Only those USB devices formatted in FAT file system (DOS 8.3 volume label) are supported.
We recommend you use USB devices that support USB 2.0 protocol with 4 MB/sec or faster
read/write speed.
o The Resume Play function may not work after you format the storage device.
o The total memory available to Delete BD Data may differ, depending on the conditions.
Anynet+(HDMI-CEC)
o Depending on your TV, certain HDMI output resolutions may not work. Please refer to the user
manual of your TV.
o This function is not available if the HDMI cable does not support CEC.
o If your Samsung TV has an Anynet+ logo, then it supports the Anynet+ function.
Selecting the Audio Language
o The ◄► indicator will not appear on the screen if the BONUSVIEW section does not contain any
BONUSVIEW audio settings.
o The languages available through the Audio Language function depend on the languages that are
encoded on the disc. This function or certain languages may not be available.
o Some Blu-ray Discs may allow you to select either the PCM or Dolby Digital audio soundtrack in
English.
Media Play
Selecting the Subtitle Language
o Depending on the Blu-ray Disc / DVD, you may be able to change the desired subtitle in the Disc
Menu. Press the DISC MENU button.
o This function depends on the selection of subtitles that are encoded on the disc and may not be
available on all Blu-ray Discs/DVDs.
o Information about the main feature BONUSVIEW mode will also appear if the Blu-ray Disc has a
BONUSVIEW section.
o This function changes both the primary and secondary subtitles at the same time.
o The total numbers of primary and secondary subtitles are displayed respectively.
o If you press the SUBTITLE button on the remote control, the subtitle bar appears.
Press the RETURN button to remove the subtitle bar.
English
69 |
Appendix
Delete BD Data
09
o What is a valid certificate?
When the product uses BD-LIVE to send the disc data and a request to the server to certify the
disc, the server uses the transmitted data to check if the disc is valid and sends the certificate
back to the product.
o The Internet connection may be restricted while you are using BD-LIVE contents.
Appendix
Resolution according to the output mode
Blu-ray Disc/E-contents/Digital Contents playback
Setup
HDMI / not
connected
HDMI / connected
Contents Type
HDMI Mode
E-contents/
Digital contents
VIDEO Mode
VIDEO Mode
1080p
576i/480i
-
Max. Resolution of TV
input
Max. Resolution
of TV input
576i/480i
-
Movie Frame : Auto (24Fs)
1080@24F
1080@24F
1080p
576i/480i
-
720p
720p
1080i
480i
720p
576i/480i
576i/480i
576p/480p
576i/480i
576i/480i
Blu-ray Disc
Resolution of Blu-ray
Disc
BD Wise
Auto
1080p
1080i
576p/480p
576i/480i
1080p
1080i
576p/480p
-
576i/480i
-
-
-
576i/480i
576i/480i
DVD playback
Output
Setup
HDMI / connected
HDMI Mode
VIDEO Mode
Auto
Max. Resolution of TV input
576i/480i
1080i
1080i
BD Wise
1080p
720p
576p/480p
576i/480i
| 70 English
576i/480i
1080p
720p
576p/480p
-
576i/480i
576i/480i
576i/480i
576i/480i
576i/480i
-
HDMI / not connected
VIDEO Mode
-
576i/480i
576i/480i
576i/480i
576i/480i
DTV View
Auto
DTV Smart
Resolution "Auto"
DTV Smart
Resolution "Off"
1080p
1080i
720p
576p/480p
576i/480i
HDMI Mode
1080p
VIDEO Mode
Resolution of
Broadcast stream
Max Resolution of
TV input
1080p
HDMI / not connected
-
Appendix
BD Wise
HDMI / connected
09
Output
Resolution
576i/480i
VIDEO Mode
576i/480i
-
576i/480i
-
1080i
576i/480i
576i/480i
576p/480p
576i/480i
576i/480i
720p
-
576i/480i
-
576i/480i
576i/480i
| NOTE |
! DTV smart resolution is activated only when resolution option is set to Auto.
! If the TV you connected to the product does not support Movie Frame or the resolution you selected, the message "If no
pictures are shown after selecting Yes, please wait for 15 seconds before returning to the previous resolution. Do you want
to change the resolution?" appears. If you select Yes, the TV’s screen will go blank for 15 seconds, and then the resolution
will revert to the previous resolution automatically.
! If the screen stays blank after you have changed the resolution, remove all discs, and then press and hold the @ button
on the front of the product for more than 5 seconds. All settings are restored to the factory default. Follow the steps on the
previous page to access each mode and select the Display Setup that your TV will support.
! When the factory default settings are restored, all stored user BD data is deleted.
! The Blu-ray Disc must have the 24 frame feature for the product to use the Movie Frame (24Fs) mode.
English
71 |
Appendix
Digital Output Selection
Setup
Connection
HDMI
supported
AV
receiver
Up to PCM
7.1ch
Up to PCM
Dolby Digital
7.1ch
Dolby Digital Up to PCM
Plus
7.1ch
Audio Stream
Up to PCM
Dolby TrueHD
on Blu-ray
7.1ch
Disc
Up to PCM
DTS
6.1ch
DTS-HD High
Up to PCM
Resolution
7.1ch
Audio
DTS-HD
Up to PCM
Master Audio
7.1ch
PCM
PCM 2ch
Up to PCM
Audio Stream Dolby Digital
5.1ch
on DVD
Up to PCM
DTS
6.1ch
PCM
Dolby Digital
Audio Stream
of Broadcast
Dolby Digital
Plus
MPEG1
Layer 2
HE-AAC
| 72 English
Bitstream
(Unprocessed)
PCM
Up to PCM
5.1ch
Optical
HDMI
supported
AV receiver
Optical
PCM 2ch
PCM
PCM 2ch
Bitstream
(Re-encoded
DTS)
HDMI
HDMI supported
supported AV
AV receiver or
receiver or
Optical
Optical
Re-encoded DTS
PCM 2ch
Dolby Digital Dolby Digital Re-encoded DTS
PCM 2ch
Dolby Digital
Dolby Digital Re-encoded DTS
Plus
PCM 2ch Dolby TrueHD Dolby Digital Re-encoded DTS
PCM 2ch
DTS
Re-encoded DTS
DTS
Re-encoded DTS
DTS
Re-encoded DTS
PCM 2ch
PCM 2ch
Re-encoded
Dolby Digital *
PCM 2ch
Dolby Digital
Dolby Digital
DTS
DTS
PCM 2ch
PCM 2ch
Dolby Digital Dolby Digital
PCM 2ch
PCM 2ch
DTS
DTS
PCM 2ch
Dolby Digital Dolby Digital Re-encoded DTS
Up to PCM
5.1ch
PCM 2ch
Dolby Digital
Dolby Digital Re-encoded DTS
Plus**
PCM 2ch
PCM 2ch
Up to PCM
5.1ch
PCM 2ch
PCM 2ch
Re-encoded
Dolby Digital *
Re-encoded
Dolby Digital *
Re-encoded
Dolby Digital *
Re-encoded
Dolby Digital *
Re-encoded
Dolby Digital *
DTS
DTS-HD High
Resolution
Audio
DTS-HD
Master Audio
PCM 2ch
PCM 2ch
Bitstream
(Re-encoded
Dolby D)
PCM 2ch
PCM 2ch
Re-encoded Re-encoded
Re-encoded DTS
Dolby Digital Dolby Digital
Re-encoded
Dolby Digital *
Re-encoded
Dolby Digital
Re-encoded
Dolby Digital
PCM 2ch
Re-encoded
Dolby Digital
Any
HDMI
supported
AV
receiver
Optical
Decodes the main feature
audio and BONUSVIEW
audio stream together
into PCM audio and adds
Navigation Sound Effects.
HDMI
supported
AV receiver
Optical
Outputs only the main
feature audio stream so that
your AV receiver can decode
the audio bitstream.
You will not hear
BONUSVIEW audio or
Navigation Sound Effects.
Bitstream
(Re-encoded
DTS)
Bitstream
(Re-encoded
Dolby D)
Decodes the main
feature audio and
BONUSVIEW audio
stream together
into PCM audio and
adds Navigation
Sound Effects, then
re-encodes the
PCM audio into DTS
bitstream.
Decodes the main
feature audio and
BONUSVIEW audio
stream together
into PCM audio and
adds Navigation
Sound Effects, then
re-encodes the PCM
audio into Dolby
Digital bitstream.
HDMI
HDMI supported
supported AV
AV receiver or
receiver or
Optical
Optical
* If the Source Stream is 2ch or mono, "Re-encoded Dolby D" setting is not applied. Output will be PCM
2ch.
** If the Audio Description is set to On, audio output will be changed Dolby Digital even if the original
broadcast stream is Dolby Digital Plus.
| NOTE |
! For Dolby Digital Plus stream on Internet Content, PCM Output via HDMI supported up to 5.1ch.
English
73 |
Appendix
Connection
Definition for
Blu-ray Disc
Bitstream
(Unprocessed)
PCM
09
Setup
Appendix
Troubleshooting
Before requesting service, please try the following solutions.
PROBLEM
SOLUTION
No operation can be performed with the
remote control.
o Check the batteries in the remote control. They may need replacing.
o Operate the remote control at a distance of no more than 6.1m.
o Remove the batteries and hold down one or more buttons for several
minutes to drain the microprocessor inside the remote control to reset it.
Reinstall the batteries and try to operate the remote control again.
Disc does not play.
o Ensure that the disc is installed with the label side facing up.
o Check the region number of the Blu-ray/DVD disc.
Disc Menu does not appear.
o Ensure that the disc has disc menus.
The prohibition message appears on the
screen.
o This message appears when an invalid button is pressed.
o The Blu-ray Disc/DVD’s software doesn’t support the feature (e.g., angles).
o You’ve requested a title or chapter number or search time that is out of
range.
Play mode differs from the Setup Menu
selection.
o Some of the functions selected in the Setup Menu may not work properly if
the disc is not encoded with the corresponding function.
The screen ratio cannot be changed.
o The Screen Ratio is fixed on your Blu-ray/DVD disc.
o This is not a problem with the product.
No audio.
o Make sure you have selected the correct Digital Output in the Audio Options
Menu.
The screen is blocked
o If the HDMI output is set to a resolution your TV cannot support (for
example, 1080p), you may not see a picture on your TV.
o Press the @ button (on front panel) for more than 5 seconds with no disc
inside. All settings will revert to the factory settings.
o When the factory default settings are restored, all stored user BD data is
deleted.
Forgot password
o Press the @ button (on front panel) for more than 5 seconds with no disc
inside. All settings including the password will revert to the factory settings.
Don’t use this unless absolutely necessary.
o When the factory default settings are restored, all stored user BD data is
deleted.
| 74 English
PROBLEM
SOLUTION
The picture is noisy or distorted
o Make sure that the disc is not dirty or scratched.
o Clean the disc.
No HDMI output.
o Check the connection between the TV and the HDMI jack of the product.
o Check if your TV supports 480p, 720p, 1080i, 1080p HDMI input
resolution.
Abnormal HDMI output screen.
o If random noise appears on the screen, it means that TV does not support
HDCP (High-bandwidth Digital Content Protection).
AllShare function
I can see folders shared through AllShare,
but I cannot see the files.
o AllShare shows only files corresponding to the Videos, Photos, and Music
categories. Files that do not correspond to these categories may not be
displayed.
Video is played intermittently.
o Check if the network is stable.
o Check if the network cable is properly connected and if the network is not
overloaded.
o The wireless connection between the DLNA compatible device and the
product is unstable.
Check the connection.
AllShare connection between product and PC o The IP address under the same subnetwork should be unique.
is unstable.
If they are not, IP interference can cause this phenomenon.
o Check if you have a firewall enabled.
If so, disable the firewall function.
English
75 |
Appendix
o Go to the contents and find the section of the user manual that contains the
explanations regarding the current problem, and follow the procedure once
again.
o If the problem still cannot be solved, please contact your nearest Samsung
authorized service centre.
09
If you experience other problems.
Appendix
PROBLEM
BD-LIVE
SOLUTION
I cannot connect to the BD-LIVE server.
o Check whether the network connection is successful or not by using the
Network Status menu. (See page 27)
o Check whether the USB memory device is connected to the product.
o The memory device must have at least 1GB of free space to accommodate
the BD-LIVE service.
You can check the available size in Delete BD Data. (See page 27)
o Check whether the BD-LIVE Internet Connection menu is set to Allow(All).
o If all above fails, contact the contents provider or update the product to the
latest firmware.
When using the BD-LIVE service, an error
occurs.
o The memory device must have at least 1GB of free space to accommodate
the BD-LIVE service.
You can check the available size in Delete BD Data. (See page 27)
Recording
"Performance test failed." message appears, o Using lower quality USB storage device not supporting Recording function
and also Schedule Recording / recording and
can cause this kind of problem.
Timeshift function does not work.
It is recommended to use USB HDD storage device.
o Recommended specification of USB HDD is at least 5400 rpm.
USB HDD of RAID type is not supported.
| NOTE |
! When the factory default settings are restored, all stored user BD data is deleted.
Repairs
If you contact us to repair your product, an administration fee may be charged if either:
1.
2.
An engineer is called out to your home at your request and there is no defect in the product.
You bring the unit to a repair centre and there is no defect in the product.
We will provide you with the amount of the administration fee before we make a home visit or begin any
work on your product.
We recommend you read this manually thoroughly, search for a solution on line at www.samsung.com,
or contact Samsung Customer Care before seeking to repair your product.
| 76 English
Specifications
Video Output
Audio Output
Network
HDD Capacity
-
Composite Video (Analogue)
Analogue
Digital
Ethernet
Wireless LAN
Security
WPS(PBC)
BD-E8500A
BD-E8900A
Appendix
HDMI
3.2 Kg
430 (W) X 300 (D) X 59 (H) mm
+5°C to +35°C
10 % to 75 %
Resolution : 1080p, 1080i, 720p, 576p/480p
PCM, Bitstream
RCA Terminal, 1.0Vp-p (75ohm load)
Resolution : 576i/480i
RCA Terminal, 2 Channel (2Vrms ± 10%)
TOS-Link Optical
100BASE-TX Terminal
Built-in
WEP(OPEN/SHARED)
WPA-PSK(TKIP/AES)
WPA2-PSK(TKIP/AES)
Supported
500GB
1TB
09
General
Weight
Dimensions
Operating Temperature Range
Operating Humidity Range
Video
Audio
Network speeds equal to or below 10Mbps are not supported.
Design and specifications are subject to change without prior notice.
For the power supply and power consumption, refer to the label attached to the product.
Weight and dimensions are approximate.
English
77 |
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer
care center.
` Asia Pacific
AUSTRALIA
NEW ZEALAND
CHINA
HONG KONG
Area
Contact Centre
1300 362 603
0800 SAMSUNG (0800 726 786)
400-810-5858
(852) 3698 4698
Web Site
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com/hk
www.samsung.com/hk_en/
VIETNAM
1800 1100 11
3030 8282
1800 3000 8282
1800 266 8282
0800-112-8888
021-5699-7777
1800-88-9999
1-800-10-SAMSUNG(726-7864) for PLDT
1-800-3-SAMSUNG(726-7864) for Digitel
1-800-8-SAMSUNG(726-7864) for Globe
02-5805777
1800-SAMSUNG(726-7864)
1800-29-3232
02-689-3232
0800-329-999
0266-026-066
1 800 588 889
www.samsung.com
U.A.E
OMAN
KUWAIT
BAHRAIN
Egypt
JORDAN
IRAN
Morocco
Saudi Arabia
800-SAMSUNG (726-7864)
800-SAMSUNG(726-7864)
183-2255
8000-4726
08000-726786
800-22273
021-8255
080 100 2255
9200-21230
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
NIGERIA
0800-726-7864
0800-10077
0302-200077
8000 0077
800-00-0077
7095- 0077
0800 724 000
0800 300 300
0685 88 99 00
0860-SAMSUNG(726-7864 )
INDIA
INDONESIA
MALAYSIA
PHILIPPINES
SINGAPORE
THAILAND
TAIWAN
` Middle East
` Africa
Ghana
Cote D’ Ivoire
Senegal
Cameroon
KENYA
UGANDA
TANZANIA
SOUTH AFRICA
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
AK68-02230H-00
AK68-02230H-00