INSTALLATION INSTRUCTIONS

3" SIDEBAR

09-18 DODGE RAM 1500 REGULAR CAB (INCL. 19-23 RAM 1500 CLASSIC)

10-23 DODGE RAM 25-5500 REGULAR CAB

PART# 223500

www.tacautoparts.com

3" SIDEBAR

09-18 DODGE RAM 1500 REGULAR CAB (INCL. 19-21 RAM 1500 CLASSIC)

10-23 DODGE RAM 25-5500 REGULAR CAB

PARTS LIST:

Qty Description

1 Driver/Left Sidebar

1 Passenger/Right Sidebar

1 Driver/Left Front Mounting Bracket

1 Passenger/Right Front Mounting Bracket

Qty Description

4 1/2” X 1-1/2” OD x 1/8" flat washers

4 12mm x 35mm Bolt/10mm Nut Plates

2 12mm x 32mm OD x 3mm Flat Washers

2 12mm Lock Washers

1 Driver/Left Front Support Bracket

1 Passenger/Right Front Support Bracket

1 Driver/Left Rear Mounting Bracket

1 Passenger/Right Rear Mounting Bracket

4 1/2” x 2” Hex Bolts

4 1/2” Lock Washers

4 8mm-1.25 x 30mm Hex Bolts

4 8mm x 28mm OD x 3mm flat washers

4 8mm Lock Washers

2 12mm Hex Nuts

4 12mm Plastic Retainers

4 10-1.50mm x 35mm Hex Bolts

6 10mm x 30mm OD x 2.5mm flat washers

6 10mm Lock Washers

2 10mm hex nut

2 10mm bolt plate

1 10mm Fish Wire

2 10mm Plastic Retainer

Passenger Side

Rear Mounting

Bracket

12mm x 35mm Bolt/10mm Nut

Plate (pictured with Plastic

Retainer installed for example)

Driver Side

Rear

Mounting

Bracket

10mm x 35mm Bolt Plate

(pictured with Plastic

Retainer and hardware)

Passenger

Side Front

Mounting

Bracket

Passenger Side Front

Support Bracket

Driver Side Front

Support Bracket

Driver Side

Front

Mounting

Bracket

Passenger/Right Sidebar

Front of Sidebar

PROCEDURE:

Driver/Left Sidebar

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS

CAREFULLY BEFORE STARTING INSTALLATION.

2. Starting at the passenger side-front of the vehicle, remove the tape covering the factory oval holes in the inner body panel located by the front tire.

3. Select (1) 10mm Bolt Plate and partially thread a Plastic Retainer onto it, (Fig 1A) . Insert the Bolt Plate into the oval hole, (Fig 1B) . Once the Bolt Plate is inserted, hold the Bolt end with one hand and tighten the Plastic Retainer with your other hand until it is tight against the body panel. IMPORTANT: The

Plastic Retainer is designed to prevent the Bolt Plate from falling into the body cavity and to aid in installing the Mounting Bracket.

FOR MID-YEAR 2015 & UP MODELS IT WILL BE NECESSARY TO USE THE 10MM FISH WIRE

TO INSTALL THIS BOLT PLATE.

Insert fish wire into small slot and fish it until threaded end is present at large slot (Figure 2A) . Pull this end out slightly and thread 10mm bolt plate onto end of fish wire (Figure 2B) . Carefully feed bolt plate into rocker panel by pulling on opposite end of fish wire. Align 10mm bolt in slot and remove fish wire. Thread the 10mm plastic retainer down the bolt plate until it is flush against the sheet metal. (Figure 2C)

www.tacautoparts.com Page 1 of 4 08/27/15(SP)

3" SIDEBAR

09-18 DODGE RAM 1500 REGULAR CAB (INCL. 19-21 RAM 1500 CLASSIC)

10-23 DODGE RAM 25-5500 REGULAR CAB

4.

Next, partially thread a Plastic Retainer onto the threaded end of a 12mm Bolt /10mm Nut Plate, (Fig

1C) .Insert the Bolt and Nut Plate with Plastic Retainer into the factory oval hole, (Figure 1B) . FOR MID-

YEAR 2015 & UP MODELS WITH PRE-INSTALLED 8mm THREADED INSERTS, SKIP THIS STEP

AND PROCEED TO STEP 5.

5. Select the passenger side front Mounting Bracket. Position the Mounting Bracket onto the 10mm Bolt

Plate. Secure the Bracket to the Bolt Plate with (1) 10mm flat washer, (1) 10mm lock washer & (1)

10mm Hex Nut (Figure 3) . Do not tighten at this time. Rotate the 12mm Bolt/10mm Nut plate until the threaded Nut end lines up with the remaining hole in the Mounting Bracket and body. Thread (1) 10mm x 35mm Hex Bolt, (1) 10mm Flat Washer and (1) 10mm Lock Washer into the threaded nut plate. For mid-year 2015 & up Rams equipped with pre-installed 8mm threaded inserts, substitute (1) 8mm x 30mm Hex Bolt, (1) 8mm Flat Washer and (1) 8mm Lock Washer for the 10mm hardware. Snug but do not tighten hardware at this time.

6. Remove the passenger side front factory body bolt. Select the passenger side Front Support Bracket.

Insert the factory body bolt through the Support Bracket and up into its original position, (Figure 3) .

Line the other end of the Support Bracket up with the oval hole in the Front Mounting Bracket. Snug but do not tighten hardware at this time.

7. Move to the passenger side rear of the vehicle and remove the tape covering the factory oval hole in the inner body panel as described in Step 2 . Thread a Plastic Retainer onto the threaded end of a Bolt and Nut Plate, (Figures 1C & 4) . Insert the Bolt and Nut Plate into the factory hole, (see Steps 3 & 4 ).

8. Select the passenger side rear Mounting Bracket. Position the Mounting Bracket onto the installed Bolt and Nut Plate. Secure it with (1) 12mm Flat Washer, (1) 12mm Lock Washer and (1) 12mm Hex Nut,

(Figure 5) . Do not tighten at this time. Rotate the Bolt and Nut plate until the threaded Nut end lines up with the remaining hole in the Mounting Bracket and body. Thread (1) 10mm x 35mm Hex Bolt, (1)

10mm Flat Washer and (1) 10mm Lock Washer into the threaded nut on the Bolt and Nut Plate.

For mid-year 2015 Rams equipped with pre-installed 8mm threaded inserts at rear location, there is no need to align threaded nut with bracket and body. Instead, substitute (1) 8mm x 30mm Hex

Bolt, (1) 8mm Flat Washer and (1) 8mm Lock Washer for the 10mm hardware. Snug, but do not tighten hardware at this time.

9. Select the passenger Sidebar and fasten it to the front Mounting Bracket and Support Bracket with the included (1) 1/2 ” x 2” Hex Bolt, (1) 1/2” Lock Washer and (1) 1/2” Flat Washer, (Figure 6) . Do not tighten hardware at this time. Attach the Sidebar to the Rear Mounting Bracket with (1) 1/2” x 2” Hex

Bolt, (1) 1/2 ” Lock Washer and (1) 1/2” Flat Washer, (Figure 5) .

10. Level and align Sidebar properly and tighten all hardware including the factory body bolt.

11. Repeat Steps 2-10 for driver Sidebar installation.

12. Do periodic inspections to the installation to make sure all hardware is secure and tight.

To protect your investment , wax this product after installing. Regular waxing is recommended to add a protective layer over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish.

For stainless steel : Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild soap may be used also to clean the Sidebar.

For gloss black finishes : Mild soap may be used to clean the Sidebar. www.tacautoparts.com Page 2 of 4 08/27/15(SP)

Fig 1A

Fig 1B

Fish Wire

Note: 8mm factory threaded holes on Mid-Year 2015 models

(Fig 2A) Thread fish wire from small slot into large slot, driver side shown

3" SIDEBAR

09-18 DODGE RAM 1500 REGULAR CAB (INCL. 19-21 RAM 1500 CLASSIC)

10-23 DODGE RAM 25-5500 REGULAR CAB

Front

Fig 1C

Rotate Bolt and Nut plate to line up Nut with this hole in body panel. On Mid –

Year 2015 models use 8mm hardware and pre-installed threaded inserts.

Passenger side shown

(Fig 2B) Thread 10mm bolt plate onto fish wire. Be careful not to pull other end of fish wire from rocker panel slot

(Fig 2C) Align 10mm bolt in slot. Driver side shown www.tacautoparts.com Page 3 of 4 08/27/15(SP)

Factory body bolt

Fig 3

3" SIDEBAR

09-18 DODGE RAM 1500 REGULAR CAB (INCL. 19-21 RAM 1500 CLASSIC)

10-23 DODGE RAM 25-5500 REGULAR CAB

PASSENGER SIDE INSTALLATION PICTURED

Front

(1) 10mm x 35mm Hex Bolt

(1) 10mm Lock Washer

(1) 10mm Flat Washer

(For Mid-Year 2015 & up

Rams with pre-installed threaded inserts use 8mm hardware) Fig 1C

(1) 10mm x 35mm Hex Bolt

(1) 10mm Lock Washer

(1) 10mm Flat Washer

(For Mid-Year 2015 & up Rams with pre-installed threaded inserts use 8mm hardware)

Rear

(1) Bolt and Nut Plate

(2) 12mm Hex Nut

(2) 12mm Lock Washer

(2) 12mm Flat Washer

Rear

(Fig 4) Rotate Bolt and Nut plate to line up the

Nut with this hole in body panel. (For mid-

Year & up 2015 models with pre-installed

8mm threaded inserts, use 8mm hardware)

Factory body bolt

Fig 5

1/2" x 2" Hex Bolt

1/2" Flat Washer

1/2" Lock Washer

Fig 6

Complete Installation www.tacautoparts.com Page 4 of 4 08/27/15(SP)