10” x 18” Pen Lathe

70-105

4001824

Operator’s Manual

Record the serial number and date of purchase in your manual for future reference.

Serial Number: _________________________ Date of purchase: _________________________

For technical support or parts questions, email [email protected] or call toll free at (877)884-5167

70-105M1

www.rikontools.com

TABLE OF CONTENTS

Specifications.................................................................................................................. 2

Safety Instructions ........................................................................................................ 3 - 6

Getting To Know Your Machine ........................................................................................... 7

Contents of Package ...................................................................................7 - 8

Installation .....................................................................................................8

Assembly ............................................................................................................ 9 - 11

Adjustments........................................................................................................ 11 - 14

Operation .................................................................................................................. 14

Maintenance ......................................................................................... 15

Electricals & Wiring Diagram .....................................................................................5 & 15

Troubleshooting .......................................................................................................... 16

Accessories ........................................................................................................................ 17

Warranty ................................................................................................................. 17

Parts Diagram ........................................................................................................... 18

Parts List ........................................................................................................... 19

SPECIFICATIONS

Motor .................................................................................................1/2 HP, TEFC

Motor Speed (no load).......................................................................... 1,700 RPM

Volts, Phase ........................................................................................ 120 V, 1 Ph

Amps, Hertz ....................................................................................... 3.7 A, 60 Hz

Swing Over Bed ............................................................................... 10” (254 mm)

Swing Over Tool Rest Base.......................................................... 7-1/4” (184 mm)

Distance Between Centers............................................................... 18” (457 mm)

Speeds ............................................................................................................... 5

Speed Ranges ................................................ 500, 1175, 1850, 2225, 3200 RPM

Spindle Rotation ....................................................... Forward Only (C-Clockwise)

Spindle Nose Threading.......................................................................... 1” x 8 TPI

Headstock Taper ............................................................................................ MT-2

Tailstock Taper ............................................................................................... MT-2

Hole Through Drive Spindle .............................................................. 3/8” (10 mm)

Hole Through Tailstock ...................................................................... 3/8” (10 mm)

Tailstock Ram Travel ................................................................... 1-3/4" (44.5 mm)

Tool Rest Post Diameter ................................................................ 5/8” (15.8 mm)

Overall Size (LxWxH)............... 35-1/2” x 10-1/2” x 14-3/4” (902 x 267 x 375 mm)

Cast Base Size (LxW) ......................................... 29-1/2” x 7-3/8” (749 x 187 mm)

Net Weight ...................................................................................... 75 lbs. (34 kg)

NOTE: The specifications, photographs, drawings and information in this manual represent the current model when the manual was prepared. Changes and improvements may be made at any time, with no obligation on the part of Rikon Power Tools, Inc. to modify previously delivered units. Reasonable care has been taken to ensure that the information in this manual is correct, to provide you with the guidelines for the proper safety, assembly and operation of this machine.

2

SAFETY INSTRUCTIONS

IMPORTANT!

Safety is the single most important consideration in the operation of this equipment.

The following

instructions must be followed at all times. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury.

There are certain applications for which this tool was designed. We strongly recommend that this tool not be modified and/or used for any other application other than that for which it was designed. If you have any questions about its application, do not use the tool until you have contacted us and we have advised you.

SAFETY SYMBOLS

SAFETY ALERT SYMBOL: Indicates DANGER, WARNING, or CAUTION. This symbol may be used

in conjunction with other symbols or pictographs.

Indicates an imminently hazardous situation, which, if not avoided, could result in death or

serious injury.

Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious

injury.

Indicates a potentially hazardous situation, which, if not avoided, could result in minor or

moderate injury.

NOTICE:

Shown without Safety Alert Symbol indicates a situation that may result in property damage.

GENERAL SAFETY

KNOW YOUR POWER TOOL. Read the owner’s manual carefully. Learn the tool’s applications, work capabilities, and its specific potential hazards.

4.

AVOID A DANGEROUS WORKING ENVIRONMENT.

DO NOT use electrical tools in a damp environment or expose them to rain.

BEFORE USING YOUR MACHINE

To avoid serious injury and damage to the tool, read and follow all of the Safety and Operating Instructions before operating the machine.

5. DO NOT use electrical tools in the presence of flammable liquids or gasses.

6. ALWAYS keep the work area clean, well lit, and organized. DO NOT work in an environment with floor surfaces that are slippery from debris, grease, and wax.

1. Some dust created by using power tools contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.

Some examples of these chemicals are:

- Lead from lead-based paints.

- Crystalline silica from bricks, cement, and other

masonry products.

- Arsenic and chromium from chemically treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

2. READ the entire Owner’s Manual. LEARN how to use the tool for its intended applications.

7. KEEP VISITORS AND CHILDREN AWAY. DO NOT permit people to be in the immediate work area, especially when the electrical tool is operating.

8. DO NOT FORCE THE TOOL to perform an operation for which it was not designed. It will do a safer and higher quality job by only performing operations for which the tool was intended.

9. WEAR PROPER CLOTHING. DO NOT wear loose clothing, gloves, neckties, or jewelry. These items can get caught in the machine during operations and pull the operator into the moving parts. The user must wear a protective cover on their hair, if the hair is long, to prevent it from contacting any moving parts.

3. GROUND ALL TOOLS. If the tool is supplied with a 3 prong plug, it must be plugged into a 3-contact electrical receptacle. The 3rd prong is used to ground the tool and provide protection against accidental electric shock.

DO

NOT remove the 3rd prong. See Grounding Instructions on the following pages.

10. CHILDPROOF THE WORKSHOP AREA by removing switch keys, unplugging tools from the electrical receptacles, and using padlocks.

3

11.

ALWAYS UNPLUG THE TOOL FROM THE

ELECTRICAL RECEPTACLE when making adjustments, changing parts or performing any maintenance.

SAFETY INSTRUCTIONS

12.

KEEP PROTECTIVE GUARDS IN PLACE AND IN

WORKING ORDER.

13. AVOID ACCIDENTAL STARTING. Make sure that the power switch is in the “OFF” position before plugging in the power cord to the electrical receptacle.

14. REMOVE ALL MAINTENANCE TOOLS from the immediate area prior to turning “ON” the machine.

25.

ALWAYS WEAR A DUST MASK TO PREVENT

INHALING DANGEROUS DUST OR AIRBORNE

PARTICLES, including wood dust, crystalline silica dust and asbestos dust. Direct particles away from face and body. Always operate tool in well ventilated area and provide for proper dust removal. Use dust collection system wherever possible. Exposure to the dust may cause serious and permanent respiratory or other injury, including silicosis (a serious lung disease), cancer, and death. Avoid breathing the dust, and avoid prolonged contact with dust. Allowing dust to get into your mouth or eyes, or lay on your skin may promote absorption of harmful material. Always use properly fitting NIOSH/OSHA approved respiratory protection appropriate for the dust exposure, and wash exposed areas with soap and water.

15.

USE ONLY RECOMMENDED ACCESSORIES. Use of incorrect or improper accessories could cause serious injury to the operator and cause damage to the tool. If in doubt, check the instruction manual that comes with that particular accessory.

16.

NEVER LEAVE A RUNNING TOOL UNATTENDED.

Turn the power switch to the “OFF” position.

DO NOT

leave the tool until it has come to a complete stop.

17.

DO NOT STAND ON A TOOL. Serious injury could result if the tool tips over, or you accidentally contact the tool.

18.

DO NOT store anything above or near the tool where anyone might try to stand on the tool to reach it.

19.

MAINTAIN YOUR BALANCE. DO NOT extend yourself over the tool. Wear oil resistant rubber soled shoes. Keep floor clear of debris, grease, and wax.

20.

MAINTAIN TOOLS WITH CARE. Always keep tools clean and in good working order. Keep all blades and tool bits sharp, dress grinding wheels and change other abrasive accessories when worn.

21.

EACH AND EVERY TIME, CHECK FOR DAMAGED

PARTS PRIOR TO USING THE TOOL. Carefully check all guards to see that they operate properly, are not damaged, and perform their intended functions. Check for alignment, binding or breaking of moving parts. A guard or other part that is damaged should be immediately repaired or replaced.

22.

DO NOT OPERATE TOOL WHILE TIRED, OR

UNDER THE INFLUENCE OF DRUGS, MEDICATION

OR ALCOHOL.

23.

SECURE ALL WORK. Use clamps or jigs to secure the work piece. This is safer than attempting to hold the work piece with your hands.

24.

STAY ALERT, WATCH WHAT YOU ARE DOING,

AND USE COMMON SENSE WHEN OPERATING A

POWER TOOL.

A moment of inattention while operating power tools may result in serious personal injury.

4

26.

USE A PROPER EXTENSION CORD IN GOOD

CONDITION. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. The table on the following page shows the correct size to use depending on cord length and nameplate amperage rating. If in doubt, use the next heavier gauge.

The smaller the gauge number, the larger diameter of the extension cord. If in doubt of the proper size of an extension cord, use a shorter and thicker cord. An undersized cord will cause a drop in line voltage resulting in a loss of power and overheating.

USE ONLY A 3-WIRE EXTENSION CORD THAT HAS

A 3-PRONG GROUNDING PLUG AND A 3-POLE

RECEPTACLE THAT ACCEPTS THE TOOL’S PLUG.

27.

ADDITIONAL INFORMATION regarding the safe and proper operation of this product is available from:

• Power Tool Institute

1300 Summer Avenue

Cleveland, OH 44115-2851

www.powertoolinstitute.org

• National Safety Council

1121 Spring Lake Drive

Itasca, IL 60143-3201

www.nsc.org

• American National Standards Institute

25 West 43rd Street, 4th Floor

New York, NY 10036

www.ansi.org

• ANSI 01.1 Safety Requirements for

Woodworking Machines and the

U.S. Department of Labor regulations

www.osha.gov

28.

SAVE THESE INSTRUCTIONS. Refer to them frequently and use them to instruct others.

SAFETY INSTRUCTIONS

ELECTRICAL SAFETY

EXTENSION CORDS

THIS TOOL MUST BE GROUNDED

WHILE IN USE TO PROTECT THE OPERATOR FROM

ELECTRIC SHOCK.

THE USE OF AN EXTENSION CORD

WITH THIS MACHINE IS NOT RECOMMENDED. For best power and safety, plug the machine directly into a dedicated, grounded electrical outlet that is within the supplied cord length of the machine.

IN THE EVENT OF A MALFUNCTION OR BREAKDOWN,

grounding provides the path of least resistance for electric current and reduces the risk of electric shock. This tool is equipped with an electric cord that has an equipment grounding conductor and requires a grounding plug (not included). The plug MUST be plugged into a matching electrical receptacle that is properly installed and grounded in accordance with ALL local codes and ordinances.

DO NOT MODIFY ANY PLUG. If it will not fit the electrical receptacle, have the proper electrical receptacle installed by a qualified electrician.

If and extension cord needs to be used, it should only be for a limited operation of the machine. The extension cord should be as short as possible in length, and have a minimum gauge size of 14AWG.

Check extension cords before each use. If damaged replace immediately. Never use a tool with a damaged cord, since touching the damaged area could cause electrical shock, resulting in serious injury.

IMPROPER ELECTRICAL CONNECTION of the equipment grounding conductor can result in risk of electric shock. The conductor with the green insulation

(with or without yellow stripes) is the equipment grounding conductor. DO NOT connect the equipment grounding conductor to a live terminal if repair or replacement of the electric cord or plug is necessary.

Use a proper extension cord. Only use cords listed by

Underwriters Laboratories (UL). Other extension cords can cause a drop in line voltage, resulting in a loss of power and overheating of tool. When operating a power tool outdoors, use an outdoor extension cord marked “W-A” or “W”.

These cords are rated for outdoor use and reduce the risk of electric shock.

CHECK with a qualified electrician or service personnel if you do not completely understand the grounding instructions, or if you are not sure the tool is properly grounded when installing or replacing a plug.

USE ONLY A 3-WIRE EXTENSION CORD THAT HAS

THE PROPER TYPE OF A 3-PRONG GROUNDING PLUG

THAT MATCHES THE MACHINE’S 3-PRONG PLUG AND

ALSO THE 3-POLE RECEPTACLE THAT ACCEPTS THE

TOOL’S PLUG. *

REPLACE A DAMAGED OR WORN CORD

IMMEDIATELY.

This tool is intended for use on a circuit that has an electrical receptacle as shown in FIGURE A. It shows a

3-wire electrical plug and electrical receptacle that has a grounding conductor. If a properly grounded electrical receptacle is not available, an adapter as shown in

FIGURE B can be used to temporarily

FIG. A

connect this plug to a 2-contact ungrounded receptacle. The adapter has a rigid lug extending from it that MUST be connected to a permanent earth ground, such as a properly grounded receptacle box.

THIS ADAPTER IS PROHIBITED IN

CANADA.

Keep the extension cord clear of the working area. Position the cord so that it will not get caught on lumber, tools or other obstructions while you are working with your power tool.

* Canadian electrical codes require extension cords

to be certified SJT type or better.

** The use of an adapter in Canada is not acceptable.

FIG. B

5

SAFETY INSTRUCTIONS

SPECIFIC SAFETY INSTRUCTIONS FOR WOOD LATHES

This machine is intended for the shaping, smoothing and finishing of solid woods and composite materials made specifically for lathe work. The permissible work piece dimensions must be observed (see Technical

Specification). Any other use not as specified, including modification of the machine or use of parts not tested and approved by the equipment manufacturer, can cause unforeseen damage and invalidate the warranty.

ATTENTION: Use of this lathe still presents risks that cannot be eliminated by the manufacturer. Therefore, the user must be aware that wood working machines are dangerous if not used with care and all safety precautions are adhered to.

1. Do not operate this machine until you have read all of the following instructions.

2. Do not attempt to operate this machine until it is completely assembled.

3. Do not turn ON this machine if any pieces are damaged or missing.

4. This machine must be properly grounded.

5. If you are not familiar with the operation of the machine, obtain assistance from a qualified person.

6. Always wear approved, safety protective eye wear and hearing protection when operating this machine.

7. Always wear a dust mask and use adequate dust collection and proper ventilation.

8. Do not wear loose clothing or jewelry when operating this machine. Keep long hair tied back.

9. Always make sure the power switch is in the OFF position prior to plugging in the machine.

10. Always make sure the power switch is in the OFF position and the machine is unplugged when doing any cleaning, assembly, setup operation, or when not in use.

11. Use only sharp lathe tools. Dull tools can damage your work and are unsafe to use.

12. When turning between centers, make sure the headstock and tailstock are snug against the work piece.

13. When face plate turning, rough-cut the work close to the finished shape before screwing it to the face plate.

14. Never jam tools into the work piece or take too big of a cut.

15. Make sure there are no loose knots, nails, staples, dirt or foreign objects in the work piece to be turned.

16. Wood should not be warped, cracked or have improperly made or cured glue joints.

17. Test spin the work piece to ensure that it does not hit the lathe bed or tool rest before turning on the lathe.

18. Start the lathe at slow speeds to check the settings, then increase the speed to your desired level for working.

19. Low speeds are best for roughing stock, and for long or large diameter work pieces.

20. If excessive vibration occurs, stop the lathe to check the work piece settings between centers or on face plates.

21. For sanding or applying finishes, remove the tool rest from the machine. Use low speeds to avoid heat build-up.

22. Never stop the machine by grabbing the work piece, faceplate or hand wheel. Let the machine stop on its own.

23. The use of any accessories or attachments not recommended may cause injury to you and damage your machine.

24. Remove material or debris from the work area. Keep the floor and work area neat and clean.

25. Keep these instructions for future reference.

This owner’s manual is not a teaching aid and is intended to show assembly, adjustments, and general use.

CALIFORNIA PROPOSITION 65 WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Your risk from exposure to these chemicals varies, depending on how often you do this type of work. To reduce your exposure, work in a well-ventilated area and with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.

For more detailed information about California Proposition 65 log onto rikontools.com.

6

P

O

J

Q

O

A

R

B

C

GETTING TO KNOW YOUR MACHINE

E

F

G

H

I

A Headstock

B Spindle

C Spur center

D

J

N

S

T

U

M

M

C

V

L

K

P

F Tool rest locking lever

G Live center

H Tailstock

I Tailstock hand wheel

J Lathe bed

K Electric cord & plug

L On / Off switch

M Motor

N Motor mount & pivot lever

O Rubber feet

P Motor pulley & cover

Q Spindle hand wheel

R Tailstock spindle lock

S Tailstock spindle (RAM)

T Tailstock locking lever

U Tool rest base

V Spindle pulley & cover

CONTENTS OF PACKAGE

Model #70-105 Pen Lathe is shipped complete in one box.

Unpacking and Clean-up

1. Carefully remove all contents from the shipping carton. Compare the contents with the list of contents to make sure that all of the items are accounted for, before discarding any packing material.

Place parts on a protected surface for easy identification and assembly. If any parts are missing or broken, please call RIKON Customer Service (877-884-5167) as soon as possible for replacements.

DO NOT turn your machine ON if any of these items are missing. You may cause injury to yourself or damage to the machine.

2. Report any shipping damage to your local distributor.

3. Clean all rust protected surfaces with ordinary house hold type grease or spot remover. Do not use; gasoline, paint thinner, mineral spirits, etc. These may damage painted surfaces.

4. Apply a coat of paste wax to the lathe bed to prevent rust. Wipe all parts thoroughly with a clean dry cloth.

5. Set packing material and shipping carton aside. Do not discard until the machine has been set up and is running properly.

7

CONTENTS OF PACKAGE

B

C

D

E

A

LIST OF LOOSE PARTS

A Lathe Bed with Headstock, Tailstock and

Motor Assemblies

B

C

D

E

F Knockout Bar

G 32mm Wrench

H

I

J

K

Tool Rest Base Assembly

6” Tool Rest

Spur Center

Live Center

Rubber Feet with mounting screw (4)

3mm & 4mm Hex Wrenches

Tailstock Hand Wheel & Screw

Manual & Warranty Card (not shown)

F

G

H

I

TOOLS NEEDED FOR ASSEMBLY

J

- Slotted Screwdriver

- 13mm & 17mm or Adjustable Wrenches

MOVING & INSTALLING THE LATHE

INSTALLATION

be needed if the motor can swing free below the bed casting when mounted on the stand plate.

1. When moving the lathe, DO NOT use the headstock assembly, motor, tool rest or tailstock assembly as this may damage the machine. Hold under the lathe’s bed to lift and move the machine.

3. For best power and safety, the lathe should be plugged directly into a dedicated grounded electrical outlet that is within the supplied cord length of the machine. The use of an extension cord is not recommended.

2. The lathe is supplied with rubber feet for use on a bench. To permanently mount the machine on a bench, use the f our mounting holes in lathe’s base. Remove the rubber feet and insert

1” to 1-1/4” thick spacers (washers, bushings, wood strips) under the lathe when screwing or bolting the machine down (mounting hardware is not provided).

NOTE: The TEFC motor requires

1” extra space below the bed to allow airflow and room to pivot the motor down for belt changes.

For mounting on a stand, the spacers may not

5. Make sure that the machine is level. If possible, secure it to a bench or its stand to the floor with lag screws (not supplied). This will reduce any possible vibration during use.

8

4. Align the machine so there is ample space in front and in back for working and moving around it. Locate it so any turning debris or kickback will not face aisles, doorways, or other work areas that bystanders may be in. Do not locate or use the machine in damp or wet conditions.

ASSEMBLY

NOTE: Pending packaging changes at the factory, some lathe parts may already be pre-assembled on the machine. The assembly steps listed should none-the-less be reviewed for information on the lathe parts and their adjustments.

THE MACHINE MUST NOT BE

PLUGGED IN AND THE POWER SWITCH MUST BE IN THE

OFF POSITION UNTIL ALL ADJUSTMENTS ARE COMPLETE.

INSTALL THE RUBBER FEET

1. Screw the rubber feet onto the four corners of lathe bed casting. The threaded post has a hex nut to secure and adjust the feet height, if necessary, if the bench is not level. FIG. 1.

FIG. 1

INSTALL THE TOOL REST BASE

1. Remove the tailstock assembly from the lathe bed. Release the locking lever handle (A) at the rear of the tailstock, and slide the tailstock assembly off of the end of the lathe bed. FIG. 2

2. Slide the tool rest base onto the lathe bed.

NOTE: To adjust the clamping action of the tool rest base, or tailstock, adjust the locking nut (B) - turn it clockwise to tighten, and counterclockwise to loosen. This nut adjustment can be done when the tool rest base or tailstock are on, or off of the lathe bed. The locking lever must be loose when the nut is adjusted. Then, with the tool rest base or tailstock installed on the bed, test the clamping action after nut adjustments are made.

3. Re-install the tailstock onto the lathe bed.

Tool Rest Base

B

FIG. 2

A

C

Tailstock

INSTALL THE TAILSTOCK HANDLE

1. With a slotted screwdriver (not supplied) attach the tailstock handle (C) to the hand wheel with the screw provided. FIG. 3.

FIG. 3

Tool

Rest

Base

Tool Rest

Locking

Lever

INSTALL THE TOOL REST

1. Loosen the locking lever on the side of the tool rest base, and insert tool rest post into the base.

2. Adjust the tool rest’s height up or down to your desired position, and then secure The tool rest base in place with is locking lever. FIG. 4.

9

FIG. 4

Tool Rest Base

Locking Lever

ASSEMBLY

THE MACHINE MUST NOT BE PLUGGED IN AND THE POWER SWITCH

MUST BE IN THE 'OFF' POSITION UNTIL ASSEMBLY IS COMPLETE.

A

INSTALL THE SPUR CENTER

Insert the spur center into the headstock spindle.

The spur center (A) has a No. 2 Morse Taper shank, that matches the taper on the inside of the headstock spindle for a secure, friction fit. FIG. 5.

NOTE: If replacing the spur center, or purchasing new centers, make sure that the item is machined with a No. 2 Morse Taper shank.

FIG. 5

Headstock

B

A

THE KNOCKOUT BAR

The knockout bar (B) is used to remove the spur center from the headstock spindle.

Insert the knockout bar into the spindle hole at opposite side from spur center. The knockout bar is then used to hit the back end of the spur center to release it from the spindle. Carefully hold the spur center as it is knocked out of the spindle, so that it does not fly out and get damaged, or injure your hand. FIG. 6.

Headstock

C

FIG. 6

INSTALL THE LIVE CENTER

Insert the live center (C) into the tailstock spindle.

This center also has a No. 2 Morse Taper shank.

FIG. 7.

To remove live center from the tailstock spindle, loosen the tailstock’s spindle locking lever and rotate the hand wheel counterclockwise to retract spindle into the body of the tailstock. The live center will automatically be pushed out of the spindle. Carefully hold the live center as it is pushed out of the spindle, so that it does not fall out and get damaged, or injure your hand.

The knockout bar (B) can also be used to release the live center from the tailstock. FIG. 8.

10

C

FIG. 7

Tailstock

Tailstock

FIG. 8

B

ASSEMBLY

INSTALLING A FACEPLATE

The 70-105 lathe is designed with pen turning in mind, and DOES NOT include a faceplate which is used for mounting wood for the making of plates, dishes, small trays and bowls up to 10” diameter. Faceplates with 1”x8 TPI threading are available separately. To mount on your lathe:

1. Securely mount your wood onto the faceplate with wood screws. The work piece should be

“rough cut” as close as possible to the finished round shape before mounting.

Faceplates

Available

Separately

FIG. 9

2. Thread the faceplate clockwise onto the headstock spindle. FIG. 9.

5. After completing your turning, remove the face- plate from the headstock spindle by reversing steps 2-3.

3. Secure the faceplate in place onto the spindle with a hex wrench, and/or an open end wrench, pending the fastening design of faceplate used.

4. Set the tool rest to the proper position and height for turning the wood. See page 14 for recommended RPM speeds for working different diameters. Set the lathe speeds accordingly - see page 12 for instructions on the process.

6. Once the faceplate has been removed from the lathe, the finished turned work can be removed from the faceplate by removing the fastening screws. The holes in the rear of your work can be filled or plugged for best appearance.

Visit RIKON’s website at www.rikontools.com for a list of accessories for use with wood lathes.

ADJUSTMENTS

ADJUSTING THE TOOL REST

The tool rest base can be easily moved along the lathe bed to position it along the length of your work piece, and also adjusted in or out to set the tool rest close to the work for turning. Loosen the tool rest base locking lever counterclockwise, slide tool rest base to a new position, and then re-tighten the base’s locking lever, clockwise.

Tool

Rest

Base

Tool Rest

Locking

Lever

Tool Rest Base

Locking Lever

To adjust the height of the tool rest, loosen the tool rest locking lever, raise or lower tool rest, then re-tighten the rest’s locking lever. FIG. 10.

FIG. 10

Note: Position the tool rest as close to the work piece as possible. It should be 1/8” above the center line of the work piece.

11

NOTE: To adjust the clamping action of the tool rest base, or the tailstock, adjust the locking nut - turn it clockwise to tighten, and counterclockwise to loosen. See FIG. 2 and instructions on page 9.

ADJUSTMENTS

ADJUSTING THE TAILSTOCK

Loosen the locking lever (A) to move the tailstock along the lathe bed to the desired position for holding your work piece. Then tighten the locking lever to secure the tailstock on the bed. FIG. 11.

C

Tailstock

To adjust the clamping action of the tailstock on the bed, adjust the lower locking nut.

See the instructions listed on page 9, FIG. 2.

Lathe Bed

B

FIG. 11

A

To adjust the tailstock spindle in or out to hold or release your work piece, loosen the locking lever

(B) and turn the hand wheel (C). The tailstock spindle (ram) (D) will travel from 0” to 1-3/4”.

When the tailstock spindle holding the live center

(E) is in a desired position, tighten the locking lever (A). FIG. 11.

THE MACHINE MUST NOT BE

PLUGGED IN AND THE POWER SWITCH MUST BE IN THE

OFF POSITION UNTIL ALL ADJUSTMENTS ARE COMPLETE.

Motor Pulley

FIG. 12

D

E

Spindle Pulley

CHANGING SPINDLE SPEEDS

The lathe features five step motor and spindle pulleys to provide different spindle speeds. Open the two access covers to change spindle speeds.

FIG. 12.

1. With the access covers open, loosen the locking lever handle (F) that secures the motor in place, and raise the motor mounting plate lever

(G) to release the belt tension on the motor and spindle pulleys.

2. Check the speed and belt position chart to determine the spindle speed required for your turning. Then move the drive belt to the desired pulley combination.

3. With the locking lever handle and motor being loose, the motor’s weight will provide the proper tension on the drive belt. Re-tighten the locking lever and close access cov ers.

NOTE: Do not put excess tension on the drive belt or excess wear or damage to the bearing or motor may result.

12

G

5 SPINDLE SPEEDS

500 RPM

(A on F)

1,175 RPM

(B on G)

A B C D E

Head

Stock

1,850 RPM

(C on H)

2,225 RPM

(D on I)

3,200 RPM

(E onJ)

F

FIG. 13

F G H I J Motor

ADJUSTMENTS

CHANGING THE DRIVE BELT

To change the belt, the whole spindle shaft needs to be shifted right, out of the headstock, towards the tailstock. This will allow the new belt to be slipped over the spindle and onto the spindle pulley. Then the whole spindle shaft assembly can be re-installed so turning can be resumed.

A

A

1. Unplug the lathe from the power source.

2. Remove any accessories from the spindle - spur center, pen mandrel, chuck, faceplate, etc..

3. Open the rear spindle pulley cover (FIG. 14,

A) and the lower, side motor pulley cover (B) to gain access to the drive belt and pulleys that are inside of the headstock and bed casting.

4. Loosen the motor mount locking lever handle

(FIG. 13, F) and lift the motor mounting plate lever (G) to loosen the tension on the belt. The belt can now be removed from the lower motor pulley (FIG. 14, B).

5. Loosen the set screws that attaches the hand wheel (C) to the spindle, and remove the hand wheel. FIG. 15.

B

C

B

FIG. 14

D

Remove

Spindle

6. Remove the set screw(s) that attaches the spindle pulley to the spindle. The pulley should now be loose on the spindle. FIG. 14, A.

NOTE: There may be two (2) set screws in the threaded hole, one on top of the other. If assembled in this manner, this stacking prevents the set screws from loosening during use.

7. Carefully knock the spindle, towards the tailstock. Use a block of wood against the spindle end to prevent any damage when it is hit with a mallet/hammer. The spindle pulley, now loose, will slide along the spindle.

FIG. 15

8. Remove the old belt, if present, and install the new belt over the spindle pulley. Return the pulley back onto the spindle, and re-install the spindle back into the headstock casting. As in step 7, carefully knock the spindle and bearings back into place with a block of wood and mallet.

9. Secure the spindle pulley in place on the spindle with the set screw(s). Make sure that the set screws engage back onto the flat section on the spindle to eliminate slippage.

13

10. Re-assemble the remaining headstock parts by reversing the procedure previously described.

Changing the Bearings

ADJUSTMENTS

If the bearings ever need to be changed, the whole spindle shaft needs to be shifted right, out of the headstock, towards the tailstock. Then the bearings can be removed from the headstock casting. With the new bearings in place, the spindle shaft assembly can be re-installed, so turning can be resumed.

1. Unplug the lathe from the power source.

2.

Remove any accessories from the spindle - spur center, pen mandrel, chuck, faceplate, etc..

4.

Carefully knock out the spindle towards the tailstock. Use a block of wood or big dowel against the spindle end to prevent any damage when it is hit with a mallet/hammer. The spindle pulley, now loose, will slide along the spindle.

5. Carefully pull out, or knock out the old bearings. Use a mallet/hammer with a block of wood against the bearings to prevent any damage to the machine. Do not remove the large retaining C-Clips from the inside of the castings. These clips properly position the bearings when in place.

3. Follow the steps 2-7 described in CHANGING

THE DRIVE BELT on page 13, to remove the hand wheel and loosen the spindle pulley from the spindle. The drive belt will be loose on the spindle.

6. Install the two new Bearings in the front and in the rear holes of the headstock.

7. Re-assemble the lathe parts by reversing the procedure previously described.

OPERATION

It is strongly recommended that you read books, trade magazines, or get formal training to maximize the potential of using your lathe, while also minimizing the risks. Before turning on the machine, review the safety precautions on pages 3 to 6. Make sure that you fully understand the features, adjustments and capabilities of the machine that are outlined throughout this manual.

Typical Lathe Turning Operations

FIG. 16 shows the lathe set up for a typical spindle turning operation. Note: Position the tool rest as close to the work piece as possible. It should be

1/8” above the center line of the work piece.

For turning plates, bowls and small turnings, a chuck or faceplates can be used (available separately). The work piece should be “rough cut” as close as possible to the finished round shape before mounting. FIG. 17.

DIAMETER

OF WORK

Under 2”

2 to 4”

4 to 6”

6 to 8”

8 to 10”

10 to 12”

ROUGHING

RPM

1520

750

510

380

300

255

GENERAL

CUTTING

RPM

3200

1600

1080

810

650

540

FINISHING

RPM

3200

2480

1650

1240

1000

830

14

FIG. 16

FIG. 17

MAINTENANCE

Turn the power switch “OFF” and disconnect the plug from the outlet prior to adjusting or maintaining the machine. DO NOT attempt to repair or maintain the electrical components of the motor. Contact a qualified service technician for this type of maintenance.

1. Before each use:

- Check the power cord and plug for any wear or damage.

- Check for any loose screws, hardware, locking handles, jigs or various lathe accessories.

- Check the area to make sure it is clear of any misplaced tools, lumber, cleaning supplies, etc. that could hamper the safe operation of the machine.

2. Avoid a build-up of wood shavings and dust.

Regularly clean all parts of the machine using a soft cloth, brush or compressed air. A general cleaning should be done after every use to avoid future problems and ensure that the machine is in ready condition for its next use.

WARNING: If blowing sawdust, wear a proper dust mask and eye protection to prevent debris from being inhaled and blowing into your eyes.

3. Keep the lathe bed free of resin and rust.

Clean it regularly with a non-flammable solvent, then coat with a light film of dry lubricant spray, or wax, to enhance passage of the tool rest and tailstock on/over the bed.

4. Keep the lathe tools sharp, and make sure the steel is not loose in the handles so that no accidents might occur. Making sure that tools are in proper operating condition will ensure that the quality of your turning will be the best possible.

5. Check all lathe accessories (spur centers, live centers, chucks, tool rests, etc.) to ensure that they are in perfect working condition.

6. The lathe’s ball bearings are lifetime lubricated, sealed, and do not need any further care.

Keep the drive belt free of oil and grease to prevent slipping on the pulleys.

WIRING DIAGRAM

This machine must be grounded. Replacement of the power supply cable should only be done by a qualified electrician. See page 5 for additional electrical information.

This tool is intended for use on a circuit that has a 120 volt electrical receptacle. The illustration on page 5 shows the type of the 120v, 3-wire electrical plug and electrical receptacle that has a grounding conductor that is required.

15

TROUBLESHOOTING

PROBLEM

Motor will not start

Motor fails to develop full power.

PROBABLE CAUSE

1. Machine is not plugged in

2. Low voltage

3. Loose connection

1. Power line is overloaded

2. Undersize wires in supply system

3. Drive belt tension is too high

4. Low voltage

5. Worn motor

REMEDY

1. Plug in machine

2. Check fuses

3. Check plug and all connections

1. Correct the overload condition

2. Increase supply wire size or elimi-

nate extension cord if one is used

3. Adjust belt tension

4. Have voltage checked by an elec-

trician and corrected, if necessary

5. Replace the motor

Motor or Spindle Stalls or will not

start

Motor overheats

Excessive Vibration.

1. Excessive depth of cut

2. Loose or broken belt

3. Worn spindle bearings

4. Improper cooling of motor

5. Worn motor

1. Reduce cutting depth

2. Check tension or replace drive belt

3. Replace bearings

4. Clean motor to increase air flow, or

reduce motor running time

5. Replace Motor

1. Motor is overloaded

2. Air flow restricted on the motor

1. Reduce load on the motor

2. Clean motor to increase air flow

1. Work piece is warped, out of round, has

major flaw, or was improperly prepared

or centered for turning

2. Worn spindle bearings

3. Worn belt

4. Motor mount bolt or handles are loose

5. Lathe is on an uneven surface

1. Correct problem by planing, band

sawing, or discard the work piece

2. Replace the bearings

3. Replace the belt

4. Tighten all bolts or handles

5. Shim the lathe stand, or adjust the

feet on the stand for stability

Tailstock Moves when applying

pressure

1. Excessive pressure being applied by the

tailstock onto the work piece

2. Tailstock is not secured in place

3. Lathe bed and tailstock mating surfaces

are greasy or oily.

1. Apply only sufficient force with the

tailstock to hold the work piece

securely between centers.

2. Tighten tailstock locking lever

3. Remove tailstock and clean bed

surfaces with a cleaner degreaser

Tailstock or Tool Rest Base do not

lock in place

1. Incorrect adjustment on locking lever

mechanism

1. Adjust the nut under the clamping

plate to increase (or decrease) the

clamping pressure of the lock levers

Machine bogs down during cutting 1. Excessive depth of cut is taken

2. Turning tools are dull

1. Decrease the depth of cut

2. Sharpen the turning tools

Tools tend to grab or dig in.

1. Dull turning tools

2. Tool rest is set too low

3. Tool rest is set too far from the work piece

4. Improper turning tool is being used

1. Sharpen the tools

2. Reposition the tool rest height

3. Set the tool rest closer to the

work piece

4. Use the correct tool for operation

For parts or technical questions contact: [email protected] or 877-884-5167.

16

ACCESSORIES

70-906 21” LATHE BED EXTENSION

70-920 LATHE STAND

Made of heavy cast iron, it bolts to the right end of the

70-105 Mini Lathe to extend the lathe’s working spindle length capacity to 39”.

Universal, all-steel

Stand adjusts from

23-1/4” to 37-1/4” long, and 24-1/2” to 34-1/2” working height.

ADDITIONAL LATHE ACCESSORIES

For additional lathe accessories or replacement parts, contact your local RIKON distributor, or visit the RIKON website at www.rikontools.com.

Tool rests, Face Plates, Drive Centers, Spur & Live

Centers, Drill Chuck & Arbor, Drive Belts, etc.

70-913 LATHE STAND EXTENSION

Universal, all-steel Stand

Extension bolts onto the

70-910 and 70-920 stands to support lathes with Bed

Extensions. The stand extension adjusts from

18-3/4” to 32-1/4” long, and

24-1/2” to 34-1/2” working height.

WARRANTY

17

8 7 6 5

PARTS DIAGRAM

4 5 5 5 6 5 7 5 8 5 9

9

2

1

3

5 5

3 2

2 1

2 2

2 3

2 4

2 5

2 6

2 7

2 8

2 9

3 0

1 0

1 1

1 2

1 3

3 1 3 2 3 3

70-105 Mini Lathe

6 0

1 6 9

2 0

1 4 1 1 1 0

1 9 1 8 1 7 5 4 5 3

5 2 5 1 5 0 4 9

4 3

1 5

4 6

4 5

4 1

4 0

3 9

4 4

4 3

4 2

4 8

9

4 7

3 4 3 5 3 6 3 7 3 8

18

PARTS LIST

70-105 10” x 18” Mini Lathe

KEY DESCRIPTION QTY PART

NO. NO.

KEY DESCRIPTION QTY PART

NO. NO.

25

26

27

28

29

30

21

22

23

24

17

18

19

20

13

14

15

16

9

10

11

12

7

8

5

6

3

4

1

2

Screw M5X10

Stationary Knob

Moving Knob

Back Lid

Washer 6

Spring Washer 6

Hex Socket Head Screw M6X25

Balance Wheel

Hex Socket Set Screw M6X10

Ball Bearing 6005-2RS

Retaining Ring 47

Headstock

Drive Pulley

Headstock Spindle

Hex Nut 10

Headstock Spur Center

Bed

Screw M5X10

Side Plate

Screw M5X10

Power Cord

Cord Strain Relief M14

Electric Box

Drive Belt 630mm

Motor Pulley

Hex Socket Head Screw M6X16

Spring Washer 6

Washer 6

Motor Plate

Screw M8X12

3

3

1

3

1

1

1

1

1

2

1

2

1

2

1

1

1

1

2

1

5

2

4

1

4

4

2

1

1

2

P70-105-17

P70-105-18

P70-105-19

P70-105-20

P70-105-21

P70-105-22

P70-105-23

P70-105-24

P70-105-25

P70-105-26

P70-105-27

P70-105-28

P70-105-29

P70-105-30

P70-105-1

P70-105-2

P70-105-3

P70-105-4

P70-105-5

P70-105-6

P70-105-7

P70-105-8

P70-105-9

P70-105-10

P70-105-11

P70-105-12

P70-105-13

P70-105-14

P70-105-15

P70-105-16

55

56

57

58

59

60

51

52

53

54

47

48

49

50

43

44

45

46

39

40

41

42

35

36

37

38

31

32

33

34

Big Washer 8

Locking Handle

Motor

Switch

Screw M4X30

Screw M4X25

Plate

Screw M5X25

Washer 5

Nut 5

Rubber Foot with Screw

Hex Nut 8

Lock Plate

Threaded Shaft

Hand Wheel

Screw M6X50

Rotation Handle

Locking Lever

Locking Handle

Tailstock Quill

Tailstock Locking Shaft

Live Center

Tailstock

Retaining Ring 10

Retaining Ring 12

Locking Lever

Locking Sleeve

Tool Rest

Tool Rest Base

Threaded Shaft & Sleeve

1

1

2

1

1

1

1

1

1

1

1

1

1

1

1

1

2

1

4

1

1

1

1

1

2

2

1

1

1

2

P70-105-47

P70-105-48

P70-105-49

P70-105-50

P70-105-51

P70-105-52

P70-105-53

P70-105-54

P70-105-55

P70-105-56

P70-105-57

P70-105-58

P70-105-59

P70-105-60

P70-105-31

P70-105-32

P70-105-33

P70-105-34

P70-105-35

P70-105-36

P70-105-37

P70-105-38

P70-105-39

P70-105-40

P70-105-41

P70-105-42

P70-105-43

P70-105-44

P70-105-45

P70-105-46

NOTE: Please reference the Manufacturer’s Part Number when calling for Replacement Parts.

For Parts under Warranty, the Serial Number of your machine is required.

19

For more information:

16 Progress Road

Billerica, MA 01821

877-884-5167 / 978-528-5380 [email protected]

70-105M1

www.rikontools.com

70-105