Zanussi FLD 1206 Instruction manual

AUDIO VIDEO SURROUND RECEIVER
KRF-X9080D
INSTRUCTION MANUAL
KENWOOD CORPORATION
About the supplied remote control
Compared to standard remote controls, the remote control supplied with this receiver has several
operation modes. These modes enable the remote control to control other audio/video components. In
order to effectively use the remote control, it is important to read the operating instructions and obtain
a proper understanding of the remote control and how to switch its operation modes (etc.).
Using the remote control without completely understanding its design and how to switch the operation
modes may result in incorrect operations.
B60-5455-00 00 MA
*5455/01-09/EN
1
(Y, X)
0404
04.6.16, 4:02 PM
Before applying the power
Units are designed for operation as follows.
U.S.A. and Canada ........................................... AC 120 V only
Australia ........................................................... AC 240 V only
Europe and U.K. ............................................... AC 230 V only
China and Russia ............................................. AC 220 V only
Other countries .......... AC 110-120 / 220-240 V switchable*
* AC voltage selection
The AC voltage selector switch on the rear panel is set to the voltage
that prevails in the area to which the unit is shipped. Before connecting
the power cord to your AC outlet, make sure that the setting position
of this switch matches your line voltage. If not, it must be set to your
voltage in accordance with the following direction.
AC voltage selector switch
AC 220240V~
Move switch lever to match
your line voltage with a
small screwdriver or other
pointed tool.
AC 110120V~
Caution : Read this page carefully to ensure safe
operation.
How to use this manual
This manual is divided into four sections, Preparations, Operations,
Remote Control, and Additional Information.
Preparations
Shows you how to connect your audio and video components to the
receiver and prepare the surround processor.
Since this receiver works with all your audio and video components,
kindly follow the instructions in this manual for the correct connections.
Operations
Shows you how to operate the various functions available on the
receiver.
Remote Control
Shows you how to operate other components using the remote control,
as well as a detailed explanation of all remote control operations. Once
you have registered your components with the proper setup codes, you’ll
be able to operate both this receiver and your other AV components (TV,
VCR, DVD player, CD player, etc.) using the remote control supplied with
this receiver.
VOLTAGE SELECTOR
Additional Information
Shows you additional information such as “In case of difficulty”
(troubleshooting) and “Specifications”.
Maintenance of the unit
Note :
Our warranty does not cover damage caused by excessive line
voltage due to improper setting of the AC voltage selector switch.
When the front panel or case becomes dirty, wipe with a soft, dry
cloth. Do not use thinner, benzine, alcohol, etc. for these agents may
cause discoloration.
Safety precautions
In regard to contact cleaner
WARNING :
TO PREVENT FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
Do not use contact cleaners because it could cause a malfunction. Be
specially careful not to use contact cleaners containing oil, for they
may deform the plastic component.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL,
WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO
ALERT THE USER TO THE PRESENCE OF UNINSULATED
“DANGEROUS VOLTAGE” WITHIN THE PRODUCT’S
ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE
TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO
PERSONS.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL
TRIANGLE IS INTENDED TO ALERT THE USER TO THE
PRESENCE OF IMPORTANT OPERATING AND
MAINTENANCE (SERVICING) INSTRUCTIONS IN THE
LITERATURE ACCOMPANYING THE APPLIANCE.
2 EN
*5455/01-09/EN
2
04.6.16, 4:02 PM
Before applying the power
Contents
Caution : Read the pages marked
safe operation.
carefully to ensure
Before applying the power ......................................................... 2
Safety precautions ...................................................................... 2
How to use this manual .............................................................. 2
Unpacking .................................................................................... 4
Preparing the remote control ...................................................... 4
Special features ........................................................................... 5
Names and functions of parts .................................................... 6
Basic remote control operations for other
components ....................................................... 38
Remote
Control
Main unit ...................................................................................... 6
Remote control unit .................................................................... 7
Setting up the system ........................................ 8
Preparations
Connecting the terminals .................................. 9
Connecting audio components ........................ 10
Connecting video components ........................ 11
Digital connections .......................................... 12
Connecting video components
(COMPONENT VIDEO) .................................... 13
Connecting a DVD player (6-channel input) ..... 14
Connecting the speakers ................................. 15
PRE OUT connections ..................................... 16
Connecting to another room (ROOM B) ........ 17
Connecting to the AV AUX jacks ..................... 18
Connecting the antennas ................................. 18
Additional
Information
Registering setup codes for other
components ..................................................... 38
Searching for your codes ................................. 38
Checking the codes ......................................... 38
Re-assigning device keys ................................ 39
Operating other components .......................... 39
Storing the remote control of the other
components ..................................................... 40
Setup code chart .............................................. 41
Cassette deck, CD player & MD recorder
operations ........................................................ 46
Other components’ operations ....................... 47
In case of difficulty .......................................... 49
Specifications .................................................. 51
Preparing for surround sound ....................... 19
Speaker settings .............................................. 19
Normal playback .............................................. 23
Preparing for playback ..................................... 23
Listening to a source component .................... 23
Adjusting the sound ......................................... 24
Recording .......................................................... 26
Recording audio (analog sources) ................... 26
Recording video ............................................... 26
Recording audio (digital sources) .................... 26
Listening to radio broadcasts ....................... 27
Operations
Tuning radio stations ....................................... 27
Presetting radio stations manually .................. 27
Receiving preset stations ................................ 28
Receiving preset stations in order (P.CALL) ... 28
Ambience effects ............................................. 30
Surround modes .............................................. 30
Surround play ................................................... 33
DVD 6-channel playback .................................. 35
Convenient functions ....................................... 35
3 EN
*5455/01-09/EN
3
04.6.16, 4:02 PM
Before applying the power
Unpacking
Preparing the remote control
Unpack the unit carefully and make sure that all accessories are
present.
FM indoor antenna (1)
AM loop antenna (1)
Remote control unit (1)
RC-R0820
Batteries (R6/AA) (2)
Loading the batteries
1 Remove the cover.
2 Insert the batteries.
3 Close the cover.
• Insert two AA-size (R6) batteries as indicated by the polarity markings.
*AC plug adapter (1)
*Use to adapt the plug on the power
cord to the shape of the wall outlet.
(Accessory only for regions where
use is necessary.)
If any accessories are missing, or if the unit is damaged or fails to operate,
notify your dealer immediately. If your unit was shipped to you directly,
notify your shipper immediately. Kenwood recommend that you retain
the original carton and packing materials in case you need to move or ship
the unit in the future.
Keep this manual handy for future reference.
Operation
When the STANDBY indicator is lit, the power turns ON when you press
the POWER RCVR key on the remote control. When the power comes
ON, press the key you want to operate.
Operating range
(Approx.)
Remote sensor
6m
Channel space switching
(Except for the Europe and Australia)
The space between radio channels has been set to the one that
prevails in the area to which the system is shipped. However, if the
current channel space setting does not match the setting in the area
where the system is to be used, for instance when you move from
area 1 or area 2 shown in the following table or vice versa, proper
reception of AM/FM broadcasts cannot be expected. In this case,
change the channel space setting in accordance with your area by
referring to the following table.
CHANNEL
Space Frequency
Area
1.
U.S.A., Canada and South
American countries
FM: 100 kHz
AM: 10 kHz
2.
Other countries
FM: 50 kHz
AM: 9 kHz
50us
75us
AM 9kHz AM 10kHz
FM50kHz FM100kHz
DE-EMPHASIS
CHANNEL SPACE
POWER RCVR
Infrared ray system
• When pressing more than one remote control key successively, press
the keys securely by leaving an interval of 1 second or more between
keys.
Notes
1. The supplied batteries may have shorter lives than ordinary batteries
due to use during operation checks.
2. When the remote-controllable distance gets shorter than before,
replace both batteries with new ones.
3. Placing the remote sensor in direct sunlight, or in direct light from a
high frequency fluorescent lamp may cause malfunction.
In such a case, change the location of the system installation to prevent
malfunction.
Turn the power OFF by pressing the POWER key before moving the
switch level. Move the switch lever to match your area with a small
screwdriver or other pointed tool, then turn the power ON again.
4 EN
*5455/01-09/EN
4
04.6.16, 4:03 PM
Before applying the power
Special features
True home theater sound
DTS 96/24
This receiver incorporates a wide variety of surround modes to bring you
maximum enjoyment from your video software. Select a surround mode
according to your equipment or the software you are going to play and
enjoy!
º
DTS 96/24 made it possible to achieve a wide frequency range of over
40 kHz by increasing the sampling frequency to 96 or 88.2 kHz.
Moreover, DTS 96/24’s ability of 24 bit resolution offers the same
frequency band and dynamic range as 96 kHz/24 bit PCM.
DTS 96/24 is, as with conventional DTS Surround, compatible with
multi-channels. Therefore, sources recorded using DTS 96/24
technologies can be played in high sampling frequency, multi-channel
audio with ordinary DVDs and CDs.
THX
THX mode activates proprietary THX features that help recreate the
cinematic experience in a home environment.
›
THX Surround EX
Neo:6
During THX Surround EX mode, film soundtracks that have been
encoded with Dolby Digital Surround EX technology are able to reproduce an extra channel which has been added during the mixing of the
program. This channel is called Surround Back.
THX Surround EX mode activates proprietary THX features that help
recreate the cinematic experience in a home environment.
›
Neo:6 is a new technology which was developed by DTS. It can produce
high grade 6 channels surround with an astonishing fidelity from 2
channels content. Neo:6 has 2 mode, "CINEMA" mode is for movie
playback and "MUSIC" mode is for music playback.
Dolby Digital and Dolby Digital EX
The DOLBY DIGITAL mode lets you enjoy full digital surround from
software processed in the Dolby Digital format. Dolby Digital provides
up to 5.1 channels of independent digital audio for better sound quality
and more powerful presence than conventional Dolby Surround.
As for Dolby Digital EX, it creates six full-bandwidth output channels
from the 5.1 channel sources. This is done using a matrix decoder that
derives three surround channels from the two in the original recording.
For best results, Dolby Digital EX should be used with movie soundtracks
recorded with Dolby Digital Surround EX.
Dolby PRO LOGIC IIx and Dolby PRO LOGIC II
DOLBY PRO LOGIC II, whilst totally compatible with its predecessor
PRO LOGIC, provides greater advantages in surround sound. It allows
user to enjoy the conventional stereo or Dolby Surround with a
convincing “5.1 like” presentation. PRO LOGIC II offers special features
for controlling the overall spatial, dimensionality and frontal sound field
imaging. PRO LOGIC II produces an impressive surround sound from
video software marked
and three-dimensional space
from music CD. When listening to music, you will be able to enjoy the
experience of sheer STEREO surround sound.
DOLBY PRO LOGIC IIx enhanced DOLBY PRO LOGIC II’s features.
It creates 6.1 channel and 7.1 channel surround sound from stereo or
5.1 channel signals. This feature provides you an astonishing ambience
effect which makes you feel you are surrounded by natural sound.
Especially 7.1 channel surround sound can produce real back sound
from Surround Back speakers.
DTS and DTS-ES
DTS (Digital Theater System) is a 5.1 channel digital audio format that
provides five full spectrum channels and one low-frequency (subwoofer)
channel for unprecedented clarity, optimum channel separation and a
(wide) dynamic range.
DTS-ES (Extended Surround) presents 6.1 channels surround system
with additional Surround Back channel which evolved from the
conventional 5.1 channels surround system. DTS-ES format that was
recorded in DVD, CD or LD comprises of two modes. DTS-ES Discrete
6.1 produce the discrete surround back which is completely independent
and DTS-ES Matrix 6.1 produces the surround back which synthesized
within the left and right surround channels using matrix technology.
DTS-ES has perfect compatibility with the conventional 5.1 channels
surround system. 6.1 channels surround with an additional surround
back presents a more natural presence and surround effects by
increasing the impression of the sound image from back.
Important:
When a DTS disc is played on a CD, LD or DVD player, noise may be
output from the analog output. It is recommended that you connect the
digital output of the player to the digital input of this unit.
DSP surround modes
The DSP (Digital Signal Processor) used for this receiver incorporates
a variety of high quality adjustable sound fields, like “ARENA”, “JAZZ
CLUB”, “THEATER”, “STADIUM” and “DISCO”. It is compatible with
almost any kind of program source.
DVD 6-channel input
If you own a DVD player equipped with 6-channel output, this receiver
allows you to obtain the full surround sound impact of DVD source
material featuring multi-channel encoding. Since the source signals are
digital and each channel is input independently, the resulting ambience
is far superior to what can be achieved with conventional surround
sound systems.
ACTIVE EQ
ACTIVE EQ mode will produce a more dynamic sound quality in any
condition. You can enjoy a more impressive sound effect when ACTIVE
EQ is turned on.
SPEAKER EQ
SPEAKER EQ function is to adjust the receiver’s audio output
characteristics with the speakers’ characteristics which differs
depending on the size of the speakers. When activating the SPEAKER
EQ function, you will be able to enjoy a more natural and dynamic sound
experience even with small size speakers.
Universal IR (InfraRed) remote control
In addition to the basic receiver, the remote control supplied with this
receiver can also operate almost all of your remote controllable audio
and video components. Just follow the simple setup procedure to
register the components you have connected.
Video up conversion
This receiver can convert the incoming composit video signals to SVideo signal.
If your monitor TV has S-Video jacks, it is not necessary to do the
composit video connections, just use an S-Video cord to connect the
receiver and your monitor TV.
5 EN
*5455/01-09/EN
5
04.6.16, 4:03 PM
Names and functions of parts
Main unit
Speaker
indicators
CLIP
Input mode
indicator indicators
MUTE
indicator
*Input channel indicators
SP
MUTE
A B
CLIP
Listen mode
indicators
OPTICAL 6CH INPUT AUTO DETECT
COAXIAL
L
C SW R
The Input channel indicaLFE
tors lights up to indicate the
channels contained in the
SL S
SB
SR
input signal. The "S"
indicator lights when the
surround component
*Input channel indicators
consists of a single
Output channel indicators
channel.
ANALOG
DSP MODE
96kHzfs
DTS DOLBY DIGITAL STEREO NEO:6
THX
MATRIX
Surround EX
DISCRETE PRO LOGIC LOUDNESS
AUTO indicator
MEMORY indicator
STEREO indicator
AUTO
MEMORY
STEREO
TUNED
Display
TUNED indicator
Frequency display
Input display
Preset channel display
Surround mode display
VOLUME CONTROL
STANDBY
THX
ON/STANDBY
A SPEAKERS B
THX
DOLBY DIGITAL
SPEAKER EQ
DTS
ACTIVE EQ
DSP
SPEAKER EQ ACTIVE EQ
DSP
STEREO INPUT MODE DIMMER
DOWN
UP
MUTE
POWER
DVD/6CH
CD/DVD
PHONO
MULTI CONTROL
TUNER
SOUND TONE
-ON –OFF
PHONES
VIDEO 1
VIDEO 2
1 POWER ON/OFF key
(
Use to turn the main power on or off.
(
2 ON/STANDBY key
Use to turn the power ON/STANDBY when
the POWER is turned on.
STANDBY indicator
3 SPEAKERS keys
£
Use to turn the A/B speakers on or off.
4 THX key
‹
Use to switch the status of THX.
5 SPEAKER EQ key
¢
Use to select SPEAKER EQ’s setting.
6 Surround LED (light-emitting diode)
indicators
THX indicator
›
Lights when the THX mode has been chosen.
THX mode may or may not be activated
depending upon the applicable playback
mode.
SPEAKER EQ indicator
∞
Lights when the receiver is in the SPEAKER
EQ mode.
ACTIVE EQ indicator
¢
Lights when the receiver is in the ACTIVE EQ
mode.
DOLBY DIGITAL indicator
‹
Lights when the receiver is in the Dolby
Digital mode.
VIDEO 3
MD/TAPE
7
8
9
0
!
@
#
$
%
LISTEN MODE
SETUP
AV AUX
S VIDEO
BAND
VIDEO
L-AUDIO-R
AUTO MEMORY
DTS indicator
‹
Lights when the receiver is in the DTS mode.
DSP indicator
‹
Lights when the receiver is in the DSP mode.
ACTIVE EQ key
¢
Use to select ACTIVE EQ’s setting.
DSP key
‹
Use to select any of the DSP mode.
STEREO key
‹
Use to switch the listen mode to STEREO.
INPUT MODE key
8
Use to switch between the full auto, digital
and analog inputs.
DIMMER key
Use to select the REC MODE.
§
Use to adjust the brightness of the display.
fi
VOLUME CONTROL knob
£
MUTE key
¢
Use to temporarily mute the sound.
PHONES jack
∞
Use for headphone listening.
Input Selector keys
£
DVD/6CH, CD/DVD, PHONO , TUNER,
VIDEO 1, VIDEO 2, VIDEO 3, MD/TAPE
Use to select input sources.
^ SOUND key
fi
Use to adjust the sound quality and the
ambience effects.
& BAND key
¶
Use to select the broadcast band.
* AUTO key
¶
Use to select the auto or manual tuning
mode.
( TONE key
¢
Use to switch the status of TONE control.
) MEMORY key
•
Use to store radio stations in the preset
memory and to start the Auto Memory.
¡ SETUP key
(
Use to select the speakers' settings etc.
™
keys
(
Use for selection adjustments during sound,
setup and preset channel functions.
£ MULTI CONTROL knob
(
Use to control a variety of settings.
¢ LISTEN MODE knob
‹
Use to select the listening mode.
∞ AV AUX (S VIDEO, VIDEO, L-AUDIO-R)
jacks
*
§ AV AUX key
*
Use to switch the input to AV AUX.
Standby mode
CAUTION
While the standby indicator is lit, a small amount of power is supplied to
the system to back up the memory. This is called standby mode. Under the
condition, the system can be turned ON by remote control unit.
The power in this equipment will not be completely cut off from the
AC wall outlet when the main switch is turned OFF.
6 EN
*5455/01-09/EN
6
04.6.16, 4:03 PM
Names and functions of parts
Remote control unit
This remote control unit can be used not only for Kenwood products but also for other non-Kenwood products by setting the appropriate manufacturer’s
setup codes.
°
(
1
VID1
TUNER
VID2
VID3
SR
TV
5
6
P. Call
P. Call
Multi
2
¡
™
Pow
er
r
we
4
)
TV
POWER
RCVR
C Po
3
3
CD
DVD
MD
TAPE
AV AUX
PHONO
2
DVD
6CH
Enter
7
£
¢
Multi
1
8
0
+ 10
4
5
6
9
+ 100
∞
TV Mute
Page
Return
OSD
Last / A/B
Exit
§
¶
•
ª
º
Guide
Disc Skip
Menu
Disc Sel.
Mute
Input Sel.
7
8
9
0
!
@
#
$
%
^
&
*
+
¢
+
Tone
CH
4
VOL
Sound
–
–
TV
VOL
+
TV Input
Tune –
–
Bass
Boost
Band
Tune +
Auto
Top Menu
Info / Flip
Setup
Dimmer
⁄
¤
‹
›
Loudness
Listen Mode
Active
EQ
DSP
Mode
Stereo
Speaker
EQ
THX
Input
Mode
Learn
fi
fl
If the name of a function on the receiver
is different from the one’s on the
remote control, the name of the remote
control key in this manual is indicated
in parentheses.
1 Source keys (MD/TAPE, CD/DVD, DVD/
6CH, TUNER, VID1, VID2, VID3, AV AUX,
PHONO)
°
When press and hold for more than 3
seconds, they are used to select the
registered components.
Input Selector keys (MD/TAPE, CD/DVD, DVD/
6CH, TUNER, VID1, VID2, VID3, AV AUX,
£
PHONO)
When press and release in less than 3 seconds,
they are used to select the input sources.
2 SRC ( source) Power key
Use to turn the other source components on
or off.
3 Numeric keys
°
Provide functions identical to those of the
original remote control supplied with the
component you are controlling.
Multi (multi control) %/fi keys
(
Use to control a variety of settings.
Use to operate other components.
P.Call @/# keys
•
Use for selection adjustments during sound,
set up and preset channel functions.
Enter key
Use to operate other components.
4 Return key
Use to operate the DVD component.
Exit key
Use to operate other components.
5 Disc Skip key
If CD is selected as the input source, this
key functions as the multi-CD player disc
skip key.
Last/ A/B key
If TAPE is selected as the input source,
this is A and B deck of a double cassette
deck.
Use to operate other components.
6 Disc Sel. key
Use to operate other components.
Input Sel. key
Use to operate other components.
7 CH +/– keys
Use to select the channels.
¢ / 4 keys
If CD, MD and DVD as the input source,
these keys function as skip keys.
8 TV Input key
Use when in TV operation.
9 TV VOL +/– keys
Use to adjust the TV’s volume.
0 1/¡ keys
If CD, MD or Tape is selected as the
input source, this key functions as
search keys.
Tune – / + keys
¶
Use to operate the tuner mode.
! 8 key
Use to operate other components.
Dimmer key
Use to select the REC MODE.
§
Use to adjust the brightness of the display.
fi
@ 3/8 key
If CD is selected as the input source, this
key functions as the play/pause key.
If MD or TAPE key is selected as input
source, this key functions as the play key.
Band key
¶
Use to select the broadcast band.
# 2 key
If Tape is selected, this key functions as
reverse play key.
Info/Flip key
Use to operate other components.
$ Listen Mode 5/∞ keys
‹
Use to select the listening mode.
% DSP Mode key
‹
Use to select any of the DSP mode.
^ Active EQ key
¢
Use to select ACTIVE EQ’s setting.
& THX key
‹
Use to switch the status of THX.
* Stereo key
‹
Use to switch the listen mode to STEREO.
( LCD (Liquid Crystal Display)
) TV key
Use to select the TV equipment.
(
¡ POWER RCVR ( receiver) key
Use to turn the receiver on or off.
™ TV Power key
Use to turn the TV on or off.
£ +100 key
Use to select the disc number with the
multi-CD player.
TV Mute key
Use to temporarily mute the TV sound.
¢ Page 5/∞ keys
Use to operate the DVD component.
∞ OSD (on screen display) key
Use to operate the DVD component.
Guide key
Use to operate other components.
§ Menu key
Use to operate other components.
¶ Mute key
¢
Use to temporarily mute the sound.
• Tone key
¢
Use to switch the status of TONE control.
Sound key
fi
Use to adjust the sound quality and the
ambience effects.
ª VOL +/– keys
£
Use to adjust the receiver’s volume.
º Bass Boost key
¢
Use to select the maximum adjustment
setting for the low frequency range.
⁄ ÷ key
If MD or Tape is selected, this key
functions as record key.
If VCR is selected, this key functions as
record key when it pressed twice
sequentially.
Top Menu key
Use to operate the DVD component.
Setup key
(
Use to select the speakers’ settings etc.
¤ Loudness key
¢
Use to switch the status of LOUDNESS.
‹ Speaker EQ key
¢
Use to select SPEAKER EQ’s setting.
› 7 key
If CD, MD, or TAPE is selected as the
input source, this key functions as the
stop key.
Auto key
¶
Use to select the auto or manual tuning
mode.
fi Learn key
Use to register other components.°
Use to memorize the operation of the
other remote controls.
‚
fl Input Mode key
8
Use to switch between the full auto,
digital and analog inputs.
7 EN
*5455/01-09/EN
7
04.6.16, 4:03 PM
Setting up the system
Make connections as shown in the following pages.
When connecting the related system components, be sure
to refer to the instruction manuals supplied with the
components you are connecting.
Do not connect the power cord to a wall outlet until all
connections are completed.
Notes
1. Be sure to insert all connection cords securely. If their connections
are imperfect, sound may not be produced or there will be noise inference.
2. Be sure to remove the power cord from the AC outlet before plugging
or unplugging any connection cords. Plugging/unplugging connection
cords without disconnecting the power cord can cause malfunctions
and may damage the unit.
3. Do not connect power cords from components whose power
consumption is larger than what is indicated on the AC outlet at the
rear of this unit.
Analog connections
Audio connections are made using RCA pin cords. These cables transfer
stereo audio signal in an “analog” form. This means the audio signal
corresponds to the actual audio of two channels. These cables usually
have 2 plugs on each end, one red for the right channel and one white for
the left channel. These cables are usually packed together with the
source unit, or are available at your local electronics retailer.
Microcomputer malfunction
If operation is not possible or an erroneous display appears, even
though all connections have been made properly, reset the
microcomputer referring to “In case of difficulty”.
o
Memory back up function
Please note that the following items will be deleted from the unit's
memory if the power cord is disconnected from the AC outlet for
approximately 1 day.
• Power mode
• Input selector settings
• Picture output
• Speaker ON/OFF
• Volume level
• BASS, TREBLE, INPUT level
• TONE ON/OFF
• LOUDNESS ON/OFF
• Dimmer level
• MD/TAPE settings
• Listen mode setting
• Speaker settings
• Distance setting
• Input mode setting
• Sound mode settings
• Broadcast band
• Frequency setting
• Preset stations
• Tuning mode
• ACTIVE EQ mode
• SPEAKER EQ mode
Input mode settings
CD/DVD, VIDEO 2, VIDEO 3 and DVD/6CH inputs each include jacks
for digital audio input and analog audio input.
The initial factory settings for audio signal playback for CD/DVD,
DVD/6CH and VIDEO 2 and VIDEO 3.
After completing connections and turning on the receiver, follow the
steps below.
INPUT MODE
Input Selector
LISTEN MODE
1 Use the Input Selector keys to select CD/DVD, VIDEO 2,
VIDEO 3 or DVD/6CH.
2 Press the INPUT MODE key.
Each press switches the setting as follows:
In DTS play mode
1 FULL AUTO (digital input, analog input)
2 DIGITAL MANUAL (digital input)
In CD/DVD, VIDEO 2, VIDEO 3 or DVD/6CH play mode
1 FULL AUTO (digital input, analog input)
2 DIGITAL MANUAL (digital input)
3 6CH INPUT (DVD/6CH input)
4 ANALOG (analog input)
Digital input:
Select this setting to play digital signals from a DVD, CD, or LD
player.
Analog input:
Select this setting to play analog signals from a cassette deck, VCR,
or record player.
Auto detect:
In “FULL AUTO” mode (AUTO DETECT indicator light up), the
receiver detects the digital or analog input signals automatically.
Priority is given to digital signal during input mode selection. The
receiver will select the input mode and listening mode automatically
during playback to match the type of input signal (Dolby Digital,
PCM, DTS) and the speaker setting. The OPTICAL and COAXIAL
indicator on the display will light up when digital signal is detected.
If the input signal is analog, the ANALOG indicator will light up.
To keep the receiver set to the currently selected listening mode,
use the INPUT MODE key to select “DIGITAL MANUAL” (manual
sound). However, even when this setting is selected, there may be
cases in which the listening mode is selected automatically to
match a Dolby Digital source signal depending on the combination
of listening mode and source signal.
At DIGITAL MANUAL, if the audio reproduction stops in the
middle due to change in the input signals, etc. press the LISTEN
MODE knob.
If the INPUT MODE key is pressed quickly, sound may not be
produced. Press the INPUT MODE key again.
8 EN
*5455/01-09/EN
8
04.6.16, 4:03 PM
Setting up the system
Connecting the terminals
1 Strip coating.
2 Loosen.
Speaker placement
Center Speaker
3 Insert.
4 Secure.
Front Speakers Subwoofer
(L, R)
Surround Speakers
(L, R)
1 Strip coating.
3 Insert the cord.
2 Push the lever.
4 Return the lever.
• Never short circuit the + and – speaker cords.
• If the left and right speakers are connected inversely or the speaker
cords are connected with reversed polarity, the sound will be unnatural
with ambiguous acoustic imaging. Be sure to connect the speakers
correctly.
Speaker impedance
After confirming the speaker impedance indications printed on the
rear panel of the receiver, connect speakers with matching
impedance ratings. Using speakers with a rated impedance other
than that indicated on the rear panel of the receiver could result in
malfunctions or damage to the speakers or receiver.
Surround Back
Left Speaker
Listening
position
Surround Back
Right Speaker
Front (Left and Right) Speakers
Place at the front left and right of the listening position. Front speakers
are required for all surround modes.
Center Speaker
Place front and center. This speaker stabilizes the sound image and
helps recreate sound motion. Required for surround playback.
Surround (Left and Right) Speakers
Place at the direct left and right, or slightly behind, the listening
position at even heights, approximately 1 meter above the ears of the
listeners. These speakers recreate sound motion and atmosphere.
Required for surround playback.
Subwoofer
Reproduces powerful deep bass sounds.
Surround Back (Left and Right) Speakers
Place the speakers directly at the rear of the listening position. The
optimum position depends mainly on the room condition.
• Although the ideal surround system consists of all the speakers
listed above, if you don't have a Center Speaker or a Subwoofer, you
can divide those signals between the available speakers in the
speaker settings steps to obtain the best possible surround
reproduction from the speakers you have available.
(
9 EN
*5455/01-09/EN
9
04.6.16, 4:03 PM
Setting up the system
Connecting audio components
To AC wall outlet
Shape of AC outlets
Australia
Except for the
Australia
L
R
IN
PHONO
IN
CD/DVD
REC OUT
PLAY IN
MD/TAPE
Cassette Deck or
MD Recorder
OUT
IN
CD or DVD Player
OUT
Moving coil (MC) cartridge
record player cannot be used
directly from the receiver unit.
It can only be used when another equalizer amplifier is connected.
OUT
Record Player
CAUTION
Be sure to adhere to the following, or proper ventilation will be blocked causing damage or fire hazard.
• Do not place any objects impairing heat radiation onto the top of the unit.
• Leave some space around the unit (from the largest outside dimension including projection) equal to or greater than, shown below.
Top panel : 50 cm
Side panel : 10 cm
Back panel : 10 cm
10 EN
*5455/10-18/EN
10
04.6.16, 4:09 PM
Setting up the system
Connecting video components
S Video jacks
About the S VIDEO
Jacks
S VIDEO
OUT
VIDEO
S VIDEO
IN
VIDEO
S VIDEO
IN
VIDEO
S VIDEO
IN
VIDEO
S VIDEO
IN
VIDEO
S VIDEO
OUT
VIDEO
S VIDEO
Use the S VIDEO Jacks to
make connections to
video components with
S VIDEO IN/OUT Jacks.
• If you use the S VIDEO
jacks to connect your video
playback components, be
sure to use the S VIDEO
jacks when connecting
your monitor and video
recording components.
OUT
VIDEO
IN
VIDEO
IN
VIDEO
IN
VIDEO
IN
VIDEO
OUT
VIDEO
DVD
MONITOR
REC OUT PLAY IN
VIDEO 1
PLAY IN
VIDEO 2
PLAY IN
VIDEO 3
Monitor TV
VIDEO
IN
Video Deck
IN
OUT
IN
Video
OUT
OUT
Audio
DVD Player or LD Player
Video
OUT
Video
OUT
Audio
DVD Player or LD Player
OUT
Audio
A video component with digital audio outputs should be connected to the VIDEO 2 or VIDEO 3 jacks.
11 EN
*5455/10-18/EN
11
04.6.16, 4:09 PM
Setting up the system
Digital connections
The digital in jacks can accept DTS, Dolby Digital, or PCM signals. Connect components capable of outputting DTS, Dolby Digital, or standard PCM (CD)
format digital signals.
If you have connected any digital components to the receiver, be sure to read the “Input mode settings” section carefully.
8
COAXIAL
OPTICAL
CD/DVD
OPTICAL
VIDEO 3
OPTICAL
MONITOR
VIDEO
2
OPTICAL DIGITAL
IN (AUDIO)
DVD/
6CH
DIGITAL IN
DIGITAL OUT
Optical
fiber cable
OPTICAL DIGITAL
OUT (AUDIO)
Optical fiber cable
MD Recorder
Component with DTS,
Dolby Digital, or PCM
OPTICAL DIGITAL OUT
Connect the video signal and analog
audio signals to the VIDEO 3 jacks.
(See “Connecting video components”.)
!
Optical fiber
cable
OPTICAL DIGITAL
OUT (AUDIO)
CD or DVD Player
COAXIAL
DIGITAL
OUT
(AUDIO)
COAXIAL DIGITAL
OUT (AUDIO)
Component with DTS,
Dolby Digital, or PCM
COAXIAL DIGITAL OUT
Connect the video signal and analog
audio signals to the VIDEO 2 jacks.
(See “Connecting video components”.)
!
RF digital demodulator
(Commercially available)
DOLBY DIGITAL RF
OUT (AUDIO)
PCM OUT
LD Player
To connect an LD player with a DIGITAL RF OUT, connect the LD player to a RF digital demodulator (commercially available).
Next, connect the DIGITAL OUT jacks of the demodulator to the DIGITAL IN jacks of the receiver.
Connect the video signal and analog audio signals to the VIDEO 2 or VIDEO 3 jacks. (See “Connecting video components”.)
12 EN
*5455/10-18/EN
12
04.6.16, 4:09 PM
Setting up the system
Connecting video components (COMPONENT VIDEO)
If you have connected the receiver to a video component with COMPONENT jacks, you can get a better picture quality than by connecting to the S-VIDEO
jacks.
COMPONENT VIDEO
VIDEO
3
IN
DVD
IN
Y
CB
CR
VIDEO 2 IN
Y
CB
Y
CB
CR
MONITOR OUT
CR
Monitor TV
(with component jacks)
CR IN
CB IN
Y IN
CR OUT
CB OUT
Video Recorder, DVD Recorder,
Satellite Cable Tuner & Game
Player (with component jacks)
Y OUT
CR OUT
CB OUT
DVD Player (with component jacks)
Y OUT
CR OUT
CB OUT
Video Recorder, DVD Recorder,
Satellite Cable Tuner & Game
Player (with component jacks)
Y OUT
When connecting the TV to the COMPONENT jacks, be sure to connect all the other components to the COMPONENT jacks.
13 EN
*5455/10-18/EN
13
04.6.16, 4:09 PM
Setting up the system
Connecting a DVD player (6-channel input)
If you have connected a DVD player to the receiver with digital connection, be sure to read the “Input mode settings” section carefully.
OUT
VIDEO
IN
VIDEO
IN
VIDEO
IN
VIDEO
IN
VIDEO
COAXIAL
OUT
VIDEO
OPTICAL
CD/DVD
OPTICAL
VIDEO 3
OPTICAL
MONITOR
VIDEO
2
DVD
MONITOR
DVD/
6CH
DIGITAL IN
S VIDEO
IN
VIDEO
S VIDEO
IN
VIDEO
DIGITAL OUT
S VIDEO
IN
VIDEO
S VIDEO
OUT
VIDEO
VIDEO
OUT
DVD
MONITOR
ROOM B
CENTER
PLAY IN
VIDEO 2
VIDEO OUT
COAXIAL
DIGITAL OUT
(AUDIO)
PLAY IN
VIDEO 3
FRONT
FRONT
OUT L/R
SURROUND
DVD/6CH INPUT
SURROUND
OUT L/R
CENTER
OUT
DVD Player
SUBWOOFER
OUT
S VIDEO
OUT
S VIDEO cord
14 EN
*5455/10-18/EN
14
04.6.16, 4:09 PM
SUB
WOOFER
8
Setting up the system
Connecting the speakers
Surround Back Speakers
Left
Surround Speakers
Right
Left
Right
Powered
Subwoofer
SURROUND
R
+
SURROUND
R
BACK
+
GRAY
L
BLUE
-
-
+
TAN
L
BROWN
-
-
+
CENTER
SUB
WOOFER
RED
WHITE
GREEN
FRONT B
+
R
L
-
+
R
FRONT A
L
-
-
+
CENTER
Left
Right
Front Speakers B
Center
Speaker
Right
Left
Front Speakers A
• To make sure that each speaker has been connected properly, pay attention to the test tone from each speaker.
Refer to “5 Adjust the speaker volume level.”.
)
• This model is designed on the assumption that a pair of Surround Back Speakers is connected.
When use only one Surround Back Speaker, connect it with either speaker terminal of “SURROUND BACK L” or “SURROUND BACK R” and
increase the volume level of the test tone by 3 dB for the channel which has been connected.
)
In this case, when “Dolby PRO LOGICIIx” is selected at LISTEN MODE, sound is output at the connected channel only.
15 EN
*5455/10-18/EN
15
04.6.16, 4:09 PM
Setting up the system
PRE OUT connections
This receiver has additional PRE OUT jacks. These can be used for various purposes, but will need to be connected to an external power amplifier as
shown in the example below.
CENTER
L
R
ROOM B
FRONT
SURROUND SURROUND
BACK
SUB
WOOFER
PRE OUT
Power Amplifier
Center Speaker
Powered
Subwoofer
Surround Back
Speakers
Power Amplifier
L
R
Surround Speakers
Power Amplifier
L
R
Front Speakers
Power Amplifier
L
R
• Connecting a speaker cord directly to a PRE OUT jack will not produce any sound from the speaker.
• To use the PRE OUT jacks, press only the SPEAKERS A key to the ON position.
• This model is designed on the assumption that a pair of Surround Back Speakers is connected.
When use only one Surround Back Speaker, connect it with either speaker terminal of “SURROUND BACK L” or “SURROUND BACK R” and
increase the volume level of the test tone by 3 dB for the channel which has been connected.
)
In this case, when “Dolby PRO LOGICIIx” is selected at LISTEN MODE, sound is output at the connected channel only.
16 EN
*5455/10-18/EN
16
04.6.16, 4:09 PM
Setting up the system
Connecting to another room (ROOM B)
This connection allows you to connect your main system to a monitor TV and speaker system located in another area (ROOM B).
CENTER
VIDEO
OUT
L
R
ROOM B
ROOM B
FRONT
SURROUND SURROUND
BACK
SUB
WOOFER
PRE OUT
Front Speakers
(Room B)
Power Amplifier
Monitor TV (Room B)
ROOM A
(Main system)
ROOM B
The sound from ROOM B PRE OUT jacks is the same as that of the Front Speakers.
When listening in another room (ROOM B), set the LISTEN mode to STEREO. ›
17 EN
*5455/10-18/EN
17
04.6.16, 4:09 PM
Setting up the system
Connecting to the AV AUX jacks
Connecting the antennas
The AV AUX jacks are convenient for connection of video components
such as a camcorder or a video game.
The broadcast reception cannot be made unless the antennas are
connected. Connect the antennas correctly as instructed below.
AM loop antenna
AV AUX
Place the supplied loop antenna as far as possible from the receiver, TV
set, speaker cords and power cord, and adjust the direction for best
reception.
AM antenna terminal connections
1 Push lever.
S VIDEO
VIDEO
2 Insert cord.
3 Release lever.
L-AUDIO-R
FM indoor antenna
The supplied indoor antenna is for temporary use only. For stable signal
reception we recommend using an outdoor antenna. Disconnect the
indoor antenna when you connect one outdoors.
FM antenna terminal connections
Insert cord.
S VIDEO cord
FM outdoor antenna
Lead the 75Ω coaxial cable connected to the FM outdoor antenna into the
room and connect it to the FM 75Ω terminal.
VIDEO OUT
S VIDEO OUT
Camcorder, other
VCR, video game or
portable MD Player
AUDIO OUT
Attach to the stand
ANTENNA
AM
• To select the source connected to the AV AUX jacks press AV
AUX key.
£
• When you connect the audio source such as the MD player, you
do not need to connect the video cable.
• When you connect the unit and the component with the S
VIDEO cord, you can enjoy better picture quality.
AM loop antenna
GND
FM indoor antenna
75
FM
FM outdoor antenna
Use an antenna
adaptor
(Commercially
available)
18 EN
*5455/10-18/EN
18
04.6.16, 4:10 PM
Preparing for surround sound
Speaker settings
To enable you to obtain optimum enjoyment from the receiver’s listening
modes, make sure to complete the speaker settings (Subwoofer, Front,
Center, and Surround Speakers) as described below.
ON/STANDBY
SETUP
4 Select a speaker system.
If you have THX certified speakers, please set them to NML/THX.
1 Select the SP SETUP and press the SETUP key again so that
the Subwoofer setting indication “SUBW ON” appears.
MULTI CONTROL
L
C SW R
LFE
SL S
SB
SP
MUTE
A B
CLIP
DTS. DOLBY DIGITAL STEREO
OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC LOUDNESS
ANALOG
96kHzfs
NEO:6
COAXIAL
CSII
THX
Surround EX
RDS
RTY
AUTO
MEMO
STEREO
TUNED
SR
2 Use the MULTI CONTROL knob or Multi (%/fi) keys to select
the appropriate Subwoofer setting.
POWER ON/OFF SOUND
1 SUBW ON : Subwoofer setting mode to the receiver is
ON.
2 SUBW OFF : Subwoofer setting mode to the receiver is
OFF.
TUNER
POWER RCVR
(Multi %/ fi,
@/#)
• The initial setting is “SUBW ON”.
• When the setting “SUBW OFF” is selected, the Front Speakers
are automatically set to “FRNT LARGE” and the procedure skips
to step 6.
Before step 6, press the SETUP key to accept the setting.
• When Subwoofer output sound is required, select “FRNT NML/
THX”, or select both “FRNT LARGE” and “SW RE-MIX ON”.
Sound
Setup
3 Press the ∧ key or # key to accept the setting.
• The Front Speakers setting indication “FRNT” appears.
1 Turn on the power to this receiver by pressing the POWER
ON/OFF and ON/STANDBY
key or POWER RCVR key.
C SW R
LFE
L
2 For the remote control, press and hold the TUNER key for
SL S
SB
SP
MUTE
A B
CLIP
DTS. DOLBY DIGITAL STEREO
OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC LOUDNESS
ANALOG
96kHzfs
COAXIAL
NEO:6
CSII
THX
Surround EX
RDS
RTY
AUTO
MEMO
STEREO
TUNED
SR
more than 3 seconds to switch to receiver mode.
3 Press the SETUP
key to enter the SETUP mode.
4 Use the MULTI CONTROL knob or Multi (%/fi) keys to select
the appropriate Front Speakers setting.
∨ keys or @/ # keys for the following displays.
Use ∧/∨
1
2
3
4
5
6
7
1 FRNT NML/THX : Average size Front Speakers are
connected to the receiver.
2 FRNT LARGE
: Large Front Speakers are connected
to the receiver.
SP SETUP
TEST TONE
BASS PEAK
SP DISTANCE
LFE LEVEL
DISP MODE
EXIT
• For “FRNT LARGE” selection, no sound will be heard from
Subwoofer even when it is set to on. However, if you select
“SW RE-MIX ON” when Subwoofer is selected, you will be able
to hear sound from the Subwoofer.
When in STEREO mode, the sound goes directly to Front
Speaker.
The flow of the SETUP is as follows:
SP
SETUP
Subwoofer
Front
TEST
TONE
BASS
PEAK
T. TONE T. TONE
AUTO MANUAL
Center
Surround
Surround
Back
Subwoofer
Re-mix
L
C
R
SR
SBR
SBL
SL
SW
SP
DISTANCE
LFE
LEVEL
DISP
MODE
Front Left
Display Selector
Center
Display Listen
L
Front Right
C
Surround Right
R
Surround Back Right
SR
Surround Back Left
SBR
Surround Left
SBL
Subwoofer
SL
EXIT
5 Press the ∧ key or # key to accept the setting.
• The Center Speaker setting indication “CNTR” appears.
6 Use the MULTI CONTROL knob or Multi (%/fi) keys to select
the appropriate Center Speaker setting.
If you selected “LARGE” as the Front Speakers setting,
1 CNTR NML/THX : An average size Center Speaker is
connected to the receiver.
2 CNTR LARGE
: A large Center Speaker is connected
to the receiver.
3 CNTR OFF
: Center Speaker setting mode to the
receiver is OFF.
If you selected “NML/THX” as the Front Speakers setting,
SW
1 CNTR NML/THX : An average size Center Speaker is
connected to the receiver.
2 CNTR OFF
: Center Speaker setting mode to the
receiver is OFF.
Continued to next page.
19 EN
*5455/19-29/EN
19
04.6.16, 4:16 PM
Preparing for surround sound
5 Adjust the speaker volume level.
7 Press the ∧ key or # key again to accept the setting.
• The Surround Speaker indication “SURR” appears.
8 Use the MULTI CONTROL knob or Multi (%/fi) keys to select
the appropriate Surround Speaker setting.
If you selected “LARGE” as the Center Speaker setting,
1 SURR NML/THX : Average size Surround Speakers are
connected to the receiver.
2 SURR LARGE
: Large Surround Speakers are
connected to the receiver.
3 SURR OFF
: Surround Speaker setting mode to
the receiver is OFF.
From your usual listening position, adjust the volume levels. The
volume levels from each speaker should be the same.
• The receiver enters the speaker volume level adjustment mode.
• Indicators appear only for the channels of the speakers selected
in step 4.
Be aware that the TEST TONE is quite a loud sound (0dB).
∨ keys or @/#keys to select TEST TONE.
1 Press the ∧/∨
2 Press the SETUP key for the following displays:
1 T.TONE AUTO
2 T.TONE MANUAL
If you selected other than “LARGE” as the Center Speaker
setting,
1 SURR NML/THX : Average size Surround Speakers are
connected to the receiver.
2 SURR OFF
: Surround Speaker setting mode to
the receiver is OFF.
• When the setting “SURR OFF” is selected, you may skip to step
!.
3 The selection of AUTO/MANUAL TEST TONE is done by the
MULTI CONTROL knob or Multi (%/fi) keys.
Press the SETUP key again to begin TEST TONE.
Use the MULTI CONTROL knob or Multi (%/fi) keys to adjust
the volume level of the test tone output from the speaker
channel to be adjusted.
For AUTO selection, the first test tone is heard from the Front
Left Speaker for 2.5 seconds. The next test tone is heard from
the speakers in the following sequence for 2 seconds each.
9 Press the ∧ key or # key again to accept the setting.
• The Surround Speaker setting indication “SB” appears.
0 Use the MULTI CONTROL knob or Multi (%/fi) keys to select
appropriate Surround Back Speaker setting.
If you selected “LARGE” as the Surround Speaker setting,
1 SB NML/THX : Average size Surround Back Speaker is
connected to the receiver.
2 SB LARGE
: Large Surround Back Speaker is connected to the receiver.
3 SB OFF
: Surround Back Speaker setting mode to
the receiver is OFF.
L
SL S
C SW R
LFE
SB
SP
MUTE
A B
CLIP
DTS. DOLBY DIGITAL STEREO
OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC LOUDNESS
COAXIAL ANALOG
96kHzfs
NEO:6
CSII
THX
Surround EX
RDS
RTY
AUTO
MEMO
STEREO
TUNED
SR
LEFT
CNTR
SUBW
SL
RIGHT
SBL
SR
SBR
The channel indication blinks while the test tone is being output.
L
SL S
C SW R
LFE
SB
SP
MUTE
A B
CLIP
DTS. DOLBY DIGITAL STEREO
OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC LOUDNESS
ANALOG
96kHzfs
COAXIAL
NEO:6
CSII
THX
Surround EX
RDS
RTY
AUTO
MEMO
STEREO
TUNED
SR
• If you change the volume level settings for the speakers while
listening to music, the settings referred to on this page are also
changed.
fi
• If the speaker setting selects are OFF, the speaker level settings
are reset.
If you selected “NML/THX” as the Surround Speaker setting,
∨ keys or @/# keys each
For MANUAL selection, press the ∧/∨
time to select the speaker channel.
1 SB NML/THX : Average size Surround Back Speaker is
connected to the receiver.
2 SB OFF
: Surround Back Speaker setting mode to
the receiver is OFF.
4 Press the SETUP key again.
• The test tone is turned off and return to the main setup displays.
! Press the ∧ key or # key again to accept the setting.
• The Subwoofer re-mix setting indication “SW RE-MIX” appears.
@ Use the MULTI CONTROL knob or Multi (%/fi) keys to select
the appropriate Subwoofer re-mix setting.
1 SW RE-MIX ON : Subwoofer re-mix setting mode to
the receiver is ON.
2 SW RE-MIX OFF : Subwoofer re-mix setting mode to
the receiver is OFF.
6 Adjust the bass peak level.
A restriction is put on the low frequency so that the bass peak level
will not go higher than the acceptable level when the volume is
increased.
If Subwoofer is OFF, the limitation will affect the low frequency of
the Front Left and Right Speakers.
∨ keys or @/ # keys to select BASS PEAK and press
1 Press the ∧/∨
the SETUP key.
SW
• If subwoofer is turned off, subwoofer re-mix setting is not visible.
# Press the SETUP key again to return to the main setup
displays.
SP
MUTE
A B
CLIP
DTS. DOLBY DIGITAL STEREO
OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC LOUDNESS
ANALOG
96kHzfs
COAXIAL
20
CSII
THX
Surround EX
RDS
RTY
2 Use the MULTI CONTROL knob or Multi (%/fi) keys to adjust
the bass peak level to –30dB.
• The adjustment range is from – 30dB to 0dB and OFF.
20 EN
*5455/19-29/EN
NEO:6
AUTO
MEMO
STEREO
TUNED
LFE
04.6.16, 4:16 PM
Preparing for surround sound
3 For optimum bass peak level, keep increasing the bass peak
level by using the MULTI CONTROL knob or Multi (%/fi)keys
while test tone is being output until clip sound is heard from
the Subwoofer or Front Speaker.
SW
SP
MUTE
A B
CLIP
DTS. DOLBY DIGITAL STEREO
OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC LOUDNESS
COAXIAL ANALOG
96kHzfs
NEO:6
CSII
THX
Surround EX
∨ keys or @/# keys to select the DISP MODE.
1 Press the ∧/∨
2 Press the SETUP key for the following displays:
1 DISP SELECTOR
2 DISP LISTEN
RDS
RTY
AUTO
MEMO
STEREO
TUNED
LFE
9 Select the display mode.
3 Use the MULTI CONTROL knob or Multi (%/fi) keys to select
the display mode.
4 Press the SETUP key to accept the setting.
L
7 Input the distance to the speakers.
: Displays the current input selector.
: Displays the current listen mode.
R
SP
MUTE
A B
CLIP
DTS. DOLBY DIGITAL
OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC
ANALOG
96kHzfs
NEO:6
CSII
COAXIAL
THX
Surround EX
SL S
• Indicators appear only for the channels of the speakers selected
in step 4.
∨ keys or @/# keys to select the SP DISTANCE
1 Press the ∧/∨
on setup displays and press the SETUP key again.
2 Measure the distance from the listening position to each of
the speakers.
SR
4 Press the SETUP key again to accept the setting.
5 Use the ∧ key or # key to select EXIT.
L
R
SP
MUTE
A B
CLIP
DTS. DOLBY DIGITAL
OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC
ANALOG
96kHzfs
NEO:6
COAXIAL
SB
CSII
THX
Surround EX
RDS
RTY
AUTO
MEMO
STEREO
TUNED
LFE
SL S
Jot down the distance to each of the speakers.
Distance to Front Left Speaker (L) : ____ feet (meters)
Distance to Center Speaker (C)
: ____ feet (meters)
Distance to Front Right Speaker (R) : ____ feet (meters)
Distance to Surround Right Speaker (SR)
: ____ feet (meters)
Distance to Surround Back Right Speaker(SBR)
: ____ feet (meters)
Distance to Surround Back Left Speaker (SBL)
: ____ feet (meters)
Distance to Surround Left Speaker (SL)
: ____ feet (meters)
Distance to Subwoofer (SW)
: ____ feet (meters)
SB
RDS
RTY
AUTO
MEMO
STEREO
TUNED
LFE
SR
6 Press the SETUP key to exit the SETUP mode.
∨ keys or @/# keys to select the speakers and the
3 Use the ∧/∨
MULTI CONTROL knob or Multi (%/fi) keys to adjust the
distance to the Front Speakers.
The speaker indicator to be adjusted blinks.
L
SL S
C SW R
LFE
SB
SP
MUTE
A B
CLIP
DTS. DOLBY DIGITAL
OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC LOUDNESS
ANALOG
96kHzfs
COAXIAL
NEO:6
CSII
THX
Surround EX
RDS
RTY
AUTO
MEMO
STEREO
TUNED
SR
Indication in feet
Indication in meters
• The allowable setting range is 1 to 30 feet (0.3 to 9.0 m),
adjustable in 1 foot (0.3 m) increments.
4 Repeat steps 3 to input the distance for each of the speakers.
5 Press the SETUP key again to return to main setup displays.
• The speakers you have selected should appear on the display.
Confirm that all the speakers have been correctly selected.
8 Adjust the LFE LEVEL (Low Frequency Effects).
∨ keys or @/# keys to select the LFE LEVEL and
1 Press the ∧/∨
press the SETUP key.
2 Use the MULTI CONTROL knob or Multi (%/fi) keys to adjust
the LFE LEVEL.
L
R
SP
MUTE
A B
CLIP
DTS. DOLBY DIGITAL
OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC
ANALOG
96kHzfs
COAXIAL
SL S
SB
NEO:6
CSII
THX
Surround EX
RDS
RTY
AUTO
MEMO
STEREO
TUNED
LFE
SR
3 Press the SETUP key again to return to main setup displays.
21 EN
*5455/19-29/EN
21
04.6.16, 4:16 PM
Preparing for surround sound
Input level adjustment (analog sources only)
If the input level of an analog source signal is too high, the CLIP indicator
will light up to indicate the source signal. Adjust the input level.
L
C
LFE
SL S
SB
R
SP
MUTE
OPTICAL 6CH INPUT AUTO D
A B
CLIP
COAXIAL
ANALOG
96k
SR
1 Use the Input Selector keys to select the source of which the
input level you want to adjust.
• You can store a separate input level for each input source.
∨ keys or @/# keys repeatedly until
2 Press the SOUND and ∧/∨
the “INPUT” indication appears.
3 Use the MULTI CONTROL knob or Multi (%/fi) keys to adjust the
input level.
L
SL S
C
LFE
SB
R
SP
MUTE
A B
CLIP
DTS. DOLBY DIGITAL
OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC
ANALOG
96kHzfs
COAXIAL
NEO:6
CSII
THX
Surround EX
RDS
RTY
AUTO
MEMO
STEREO
TUNED
SR
• The adjustment mode is displayed for approximately 20 seconds.
• The input level may be adjusted to any one of three settings:
0dB, -3dB, and -6dB. (The initial setting is 0dB.)
4 Press the SOUND key again to return to the input indication.
22 EN
*5455/19-29/EN
22
04.6.16, 4:16 PM
Normal playback
Listening to a source component
Preparing for playback
Some preparatory steps are needed before starting playback.
VOLUME CONTROL
ON/STANDBY
SPEAKERS
INPUT MODE
Input Selector
POWER ON/OFF MD/TAPE
AV AUX
Input Selector
Turning on the receiver
VOL
/
1 Turn on the power to the related components.
2 Turn on the power to this receiver by pressing the POWER
ON/OFF and ON/STANDBY key.
Selecting the input mode
If you have selected a component connected to the CD/DVD, VIDEO 2,
VIDEO 3 or DVD/6CH jacks, make sure that the input mode setting is
correct for the type of audio signal to be used.
8
Selecting MD/TAPE
Select the source name corresponding to the component connected
to the MD/TAPE jacks. The initial factory setting is “TAPE”. To
change the source to “MD”, follow the steps below:
Hold down the MD/TAPE key for more than 2 seconds.
• The source indication changes to “MD”.
• To return to the original indication, repeat the above procedure.
Press the SPEAKERS key to select the speaker system to be
used.
:
B ON
:
A+B ON :
A+B OFF :
source you want to listen to.
Selecting a source using each key.
1
2
3
4
5
6
7
8
9
“DVD/6CH”
“CD/DVD”
“PHONO”
“TUNER”
“VIDEO 1”
“VIDEO 2“
“VIDEO 3”
“MD/TAPE”
“AV AUX”
2 Start playback from the selected source.
Selecting the speaker system
A ON
1 Use the Input Selector and AV AUX key to select the
3 Use the VOLUME CONTROL knob or VOL +/– keys to adjust
the volume.
Sound from the speakers connected to the SPEAKERS A
terminals on the rear panel.
Sound from the speakers connected to the SPEAKERS B
terminals on the rear panel. No sound will be heard from
the subwoofer.
Sound from both the speakers connected to the
SPEAKERS A and B terminals on the rear panel.
No sound from the speakers. Use this setting when
listening with headphones for stereo sound in all playback
modes. The display segments are different depending on
the type of input signal.
The indicator for the speakers
you want to use should be lit.
L
SL S
C
LFE
SB
R
SP
MUTE
A B
CLIP
OPTICAL 6CH INPUT AUTO DETECT CIN
ACT
DS
ANALOG
96kHzfs
COAXIAL
SR
• Selecting “6CH INPUT” by pressing the INPUT MODE key, whereby
“DVD/6CH” is the input source will cause SPEAKERS A to be selected
automatically.
23 EN
*5455/19-29/EN
23
04.6.16, 4:16 PM
Normal playback
Adjusting the sound
Once-touch low frequency emphasis (BASS BOOST)
(remote control only)
SPEAKER EQ ACTIVE EQ
SPEAKERS
TONE MULTI CONTROL
You can adjust the sound quality when the receiver is in the PCM stereo
mode, analog stereo mode and when “THX OFF”.
Press the Bass Boost key.
• Press the key once to select the maximum (+10) low frequency
emphasis setting.
• This key does not function when the receiver is in the sound quality
or ambience effects adjustment mode.
• This function is available only for speakers connected to FRONT A
terminals.
MUTE VOLUME
CONTROL
PHONES
Switching back to the previous setting
Press the Bass Boost key again.
TUNER
POWER RCVR
Tone
(Multi %/ fi)
Adjusting the LOUDNESS mode (remote control only)
Mute
You can adjust the Loudness function which controls the low volume
settings to maintain the music's richness. The adjustment can be made
when the receiver is in the PCM stereo mode, analog stereo mode and
when “THX OFF”.
VOL /
Bass Boost
Loudness
Speaker EQ
Active EQ
Press the Loudness key to turn the LOUDNESS setting ON.
• This function is available only for speakers connected to FRONT A
terminals.
To cancel
Adjusting the TONE
You can adjust the sound quality when the receiver is in the PCM stereo
mode, analog stereo mode and when “THX OFF”.
Press the Loudness key again so that the “LOUDNESS” indicator
goes off.
1 For the remote control, press and hold the TUNER key for more
than 3 seconds to switch to receiver mode.
Muting the sound
2 Press the TONE key to select the TONE mode.
Press the MUTE key.
The MUTE key lets you mute the sound of the speakers.
3 Use the MULTI CONTROL knob or Multi (%/fi) keys to select
TONE ON/OFF.
L
C
LFE
SL S
R
SB
SP
MUTE
A B
CLIP
DTS. DOLBY DIGITAL STEREO
OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC LOUDNESS
ANALOG
96kHzfs
COAXIAL
NEO:6
CSII
THX
Surround EX
RDS
RTY
SR
BASS : Select this to adjust the low frequency range.
TREBLE : Select this to adjust the high frequency range.
5 Use the MULTI CONTROL knob or Multi (%/fi) keys to adjust the
sound quality.
SL S
C
LFE
SB
R
L
AUTO
MEMO
STEREO
TUNED
4 When in TONE ON selection, press the TONE key for the following
displays.
L
Blinks
SP
MUTE
A B
CLIP
DTS. DOLBY DIGITAL STEREO
OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC LOUDNESS
ANALOG
96kHzfs
COAXIAL
NEO:6
CSII
THX
Surround EX
RDS
RTY
AUTO
MEMO
STEREO
TUNED
SR
SL S
C
LFE
SB
R
SP
MUTE
A B
CLIP
OPTICAL 6CH INPUT AUTO DETECT CIN
AC
DS
ANALOG
96kHzfs
COAXIAL
SR
To cancel
Press the MUTE key again so that the “MUTE” indicator goes off.
• MUTE ON can also be deactivated by turning the VOLUME
CONTROL knob or pressing VOL +/– keys.
ACTIVE EQ mode
You can enjoy a more impressive sound effect when ACTIVE EQ is
turned ON.
Press the ACTIVE EQ key for the following selections;
• The bass and treble levels are adjustable from -10 to +10 in 2 step
increments.
• The adjustment item is displayed for approximately 20 seconds.
• This function is available only for speakers connected to FRONT A
terminals.
1 ACTIVE EQ MUSIC
: Effective when listening to music.
(The ACTIVE EQ indicator lights up.)
2 ACTIVE EQ CINEMA : Effective when watching a movie.
(The ACTIVE EQ indicator lights up.)
3 ACTIVE EQ TV
: Effective when watching TV.
(The ACTIVE EQ indicator lights up.)
4 ACTIVE EQ OFF
: The ACTIVE EQ function is turned OFF.
(The ACTIVE EQ indicator goes off.)
• “ACTIVE EQ” will scroll from right to left.
• ACTIVE EQ function will not be available when in REC MODE, or
when searching or presetting radio stations.
24 EN
*5455/19-29/EN
24
04.6.16, 4:16 PM
Normal playback
SPEAKER EQ mode
Listening with headphones
SPEAKER EQ function is to adjust the receiver’s audio output
characteristics with the speakers’ characteristics which differs depending
on the size of the speakers. When activating the SPEAKER EQ function,
you will be able to enjoy a more natural and dynamic sound experience
even with small size speakers.
1 Press the A and B Speaker keys so that the speaker indicator
goes off.
Make sure the SPEAKERS
indicators are turned off.
Press the SPEAKER EQ key to switch the following setting;
L
1 SPEAKER EQ SMALL
: To select a small size speaker.
(The SPEAKER EQ indicator lights up.)
2 SPEAKER EQ MEDIUM : To select a medium size speaker.
(The SPEAKER EQ indicator lights up.)
3 SPEAKER EQ OFF
: The SPEAKER EQ function is turned
OFF.
(The SPEAKER EQ indicator goes off.)
• “SPEAKER EQ” will scroll from right to left.
• SPEAKER EQ function will not be available when in REC MODE,
or when searching or presetting radio stations.
• SPEAKER EQ function will not be available when “LARGE” is
selected for Front Speaker at the speaker settings.
R
SP
MUTE
OPTICAL 6CH INP
A B
CLIP
COAXIAL
ANA
LFE
SL S
SB
SR
• If you turn off all of the speakers when in surround mode, the surround
mode will be cancelled as well, resulting in stereo playback.
2 Connect headphones to the PHONES jack.
PHONES
3 Use the VOLUME CONTROL knob or VOL +/– keys to adjust
the volume.
25 EN
*5455/19-29/EN
25
04.6.16, 4:16 PM
Recording
Recording audio (analog sources)
3 Press and hold the DIMMER key for more than 2 seconds to select
the REC MODE AUTO or REC MODE MANUAL.
1 REC MODE off
: The digital input record mode is
switched off.
2 REC MODE AUTO
: The digital input signals (DTS, Dolby
Digital, or PCM) are identified
automatically and converted into stereo
signals that are ready for recording.
3 REC MODE MANUAL : The input signal type at the moment
this mode is selected is held
throughout this mode.
MD/TAPE
Recording a music source
2 Set the MD or TAPE recorder to record.
• When the REC MODE MANUAL is selected, the digital input signal
is converted to stereo signals (down-mix). But once the digital signal
is changed to other signal, no signal is output.
When the REC MODE AUTO is selected, the digital input signal is
converted to stereo signals even if the digital sign
3 Start playback, then start recording.
For REC MODE AUTO :
1 Use the Input Selector keys to select the source (other than “MD/
TAPE”) you want to record.
L
Recording video
SL S
C
LFE
SB
R
SP
MUTE
A B
CLIP
DTS. DOLBY DIGITAL STEREO
OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC LOUDNESS
ANALOG
96kHzfs
COAXIAL
NEO:6
CSII
THX
Surround EX
RDS
RTY
AUTO
MEMO
STEREO
TUNED
SR
1 Use the Input selector keys to select the video source (other than
“VIDEO 1”) you want to record.
2 Set the video deck connected to VIDEO 1 to record.
• Select the REC mode to record a digital input source.
3 Start playback, then start recording.
• Recording may not be normal for some video software. This is due
to the copy guard condition.
o
L
SL S
C
LFE
SB
R
SP
MUTE
A B
CLIP
DTS. DOLBY DIGITAL STEREO
OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC LOUDNESS
ANALOG
96kHzfs
COAXIAL
NEO:6
CSII
THX
Surround EX
RDS
RTY
AUTO
MEMO
STEREO
TUNED
SR
For REC MODE MANUAL :
Recording audio (digital sources)
L
Switch on the REC MODE to record a digital input source.
Usually use the REC MODE AUTO to record audio input sources. When
the digital mode changes during recording in the REC MODE AUTO, the
audio input source may be interrupted momentarily.
SL S
Recording music in REC MODE AUTO or MANUAL
L
SL S
C
LFE
SB
C
LFE
SB
R
SP
MUTE
A B
CLIP
DTS. DOLBY DIGITAL STEREO
OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC LOUDNESS
ANALOG
96kHzfs
COAXIAL
NEO:6
CSII
THX
Surround EX
SR
R
RDS
RTY
AUTO
MEMO
STEREO
TUNED
SP
MUTE
A B
CLIP
DTS. DOLBY DIGITAL STEREO
OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC LOUDNESS
ANALOG
96kHzfs
COAXIAL
NEO:6
CSII
THX
Surround EX
RDS
RTY
AUTO
MEMO
STEREO
TUNED
SR
DIMMER
4 Start playback, then start recording.
• If the audio reproduction stops in the middle due to change in the
input signals, etc., press the DIMMER key.
Input Selector
1 Use the Input Selector keys to select the source (CD/DVD,
DVD/6CH, VIDEO 2, VIDEO 3 ) you want to record.
2 Set the MD or TAPE recorder to record.
26 EN
*5455/19-29/EN
26
04.6.16, 4:16 PM
Listening to radio broadcasts
The receiver can store up to 40 stations in the memory and recall them
by one-touch operation.
Presetting radio stations manually
Tuning radio stations
MULTI CONTROL
MULTI CONTROL
BAND
TUNER
TUNER
AUTO
1 Tune to the station you want to store.
2 Press the MEMORY key while receiving the station.
TUNER
Blinks for 20 seconds
(Multi %/ fi)
L
SL S
Band
Tune – 1
Tune + ¡
1 Use the TUNER key to select the tuner.
2 Use the BAND key to select the desired broadcast band.
Each press switches the band.
SL S
C
LFE
R
SB
SP
MUTE
A B
CLIP
C
LFE
SB
R
SP
MUTE
A B
CLIP
Lights for 20 seconds
DTS. DOLBY DIGITAL STEREO
OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC LOUDNESS
COAXIAL ANALOG
96kHzfs
NEO:6
CSII
THX
Surround EX
RDS
RTY
AUTO
MEMORY
STEREO
TUNED
SR
Proceed to step 3 within 20 seconds.
(If more than 20 seconds elapse, press the MEMORY key again).
Auto
L
MEMORY
DTS. DOLBY DIGITAL STEREO
OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC LOUDNESS
ANALOG
96kHzfs
NEO:6
COAXIAL
CSII
THX
Surround EX
RDS
RTY
AUTO
MEMO
STEREO
TUNED
SR
3 Use the MULTI CONTROL knob or Multi (%/ fi) keys to select
one of the station presets (1 – 40).
4 Press the MEMORY key again to confirm the setting.
• Repeat steps 1, 2, 3 and 4 to store as many stations as
necessary.
• If you store a station at a previously used preset, the old station will
be replaced by the new one.
3 Use the AUTO key to select the desired tuning method.
Each press switches the tuning method to either auto or manual
tuning.
“AUTO” indicator lights up in the display.
DTS. DOLBY DIGITAL STEREO
CAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC LOUDNESS
ANALOG
96kHzfs
XIAL
NEO:6
CSII
RDS
RTY
THX
Surround EX
AUTO
MEMO
STEREO
TUNED
• Normally, set to “AUTO” (auto tuning). If the radio waves are weak
and there is a lot of interference, switch to manual tuning. (With
manual tuning, stereo broadcasts will be received in monaural.)
4 Use the MULTI CONTROL knob or Multi (% / fi ) keys, or
Tune – 1 /+ ¡ keys to select the station.
“STEREO” lights when a broadcast is being received in stereo.
DTS. DOLBY DIGITAL STEREO
TICAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC LOUDNESS
AXIAL ANALOG
96kHzfs
NEO:6
CSII
THX
Surround EX
RDS
RTY
AUTO
MEMO
STEREO
TUNED
“TUNED” is displayed when a station is received.
Auto tuning
: The next station is tuned automatically.
Manual tuning : Turn the knob or use the Multi (%/fi) keys to
select the desired station.
27 EN
*5455/19-29/EN
27
04.6.16, 4:16 PM
Listening to radio broadcasts
Receiving preset stations
Receiving preset stations in order (P.CALL)
TUNER
TUNER
(P.Call @/#)
Numeric keys
1 Press the TUNER key to select tuner as the source.
2 Enter the number of the preset station you want to receive
(up to “40”).
• Each time you press the key, another preset station is received in
order.
Press the numeric keys in the following order:
For “15”, press
For “20”, press
1 Press the TUNER key to select the tuner as the source.
2 Use the P.Call @/ # keys to select the desired station.
0, 5
0, 0, )
Pressing the P.Call # does the following:
• If you make a mistake entering a two digit number, press the +10
key repeatedly to return to the original display and start again.
L
SL S
C
LFE
SB
R
SP
MUTE
A B
CLIP
DTS. DOLBY DIGITAL STEREO
OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC LOUDNESS
ANALOG
96kHzfs
COAXIAL
NEO:6
CSII
THX
Surround EX
RDS
RTY
Pressing the P.Call @ does the following:
AUTO
MEMO
STEREO
TUNED
SR
Holding down the # or @ key, lets you skip through the presets,
receiving each preset station at 0.5 second intervals.
28 EN
*5455/19-29/EN
28
04.6.16, 4:17 PM
Listening to radio broadcasts
29 EN
*5455/19-29/EN
29
04.6.16, 4:17 PM
Ambience effects
This receiver is equipped with listening modes that allow you to enjoy an enhanced sonic ambience with a variety of video
sources.
In order to obtain the optimum effect from the surround modes, make sure to input the proper speaker settings beforehand.
(
Surround modes
The below speaker placements are for 5.1 channel surround sound
system which are;
• Dolby Digital
• Dolby Pro Logic II
• THX
• DTS
• DTS 96/24
• DSP
• DVD 6-channel
The below speaker placements are for 6.1 or 7.1 channel surround
sound system which are;
• Dolby Digital EX*
• DTS-ES*
• THX Surround EX*
• Neo:6*
• Dolby Pro Logic IIx
(*The same signal comes out from SBL and SBR.)
TV / SCREEN
TV / SCREEN
L
SW
C
R
SL
L
SR
SW
C
R
SL
SR
SBL
SBR
No Surround Back speaker
With Surround Back Left and Right Speakers
Even if the speaker configuration is different from above, this receiver
will let you enjoy Dolby Digital and DTS sources in a suitable condition
for every speaker configuration.
Manufactured under license from Dolby Laboratories. “Dolby”,
“Pro Logic”, “Surround EX” and the double-D symbol are trademarks of Dolby Laboratories.
L
SW
C
R
SL
SR
SBL
SBR
“DTS”, ”DTS-ES”, “Neo:6”
and “DTS 96/24” are trademarks of Digital Theater Systems, Inc.
Front Left speaker
Subwoofer
Center speaker
Front Right speaker
Surround Left speaker
Surround Right speaker
Surround Back Left speaker
Surround Back Right speaker
THX is a trademark or registered trademark of THX Ltd. Surround EX
is a jointly developed technology of THX and Dolby Laboratories, Inc.
and is a trademark of Dolby Laboratories, Inc. Used under authorization. All rights reserved.
30 EN
*5455/30-37/EN
30
04.6.16, 2:17 PM
Ambience effects
Dolby Digital
DTS
The Dolby Digital surround format lets you enjoy up to 5.1
channels of digital surround sound from Dolby Digital program
).
sources (such as Laserdisc or DVD software marked
Compared with previous Dolby surround, Dolby Digital provides
even better sound quality, greater spatial accuracy, and improved
dynamic range.
The DTS multi-channel audio format is available on CD, LD and
DVD software. DTS is a strictly digital format and cannot be
decoded inside most CD, LD or DVD players. For this reason, if you
attempt to listen to DTS encoded software through the analog
output of your new CD, LD or DVD player, you will experience
digital noise in most cases. This noise can be quite loud if the
analog output is connected directly to a high power amplification
system. Proper measures for playing the digital output as described below should be taken to avoid this situation. To enjoy DTS
Digital Surround playback, an external 5.1 channel DTS Digital
Surround decoder system or an amplifier with a built-in DTS Digital
Surround decoder must be connected to the digital output (S/P
DIF, AES/EBU or TosLink) of a CD, LD or DVD player.
All models are incorporated with the DTS decoder.
Dolby Digital EX
Dolby Digital EX is an extension of Dolby Digital technology, Dolby
Digital EX creates six full-bandwidth output channels from 6.1channel sources. This is done using a matrix decoder that derives
three surround channels from the two in the original recording.
This is achieved by using three different surround signals, surround left, surround right, and surround back, each driving its own
array of speakers. Think of it as adding a center channel for the rear
speakers, which give more diffuse and natural surround effect,
even if you wanted the ability to completely encircle the audience
with sound, positioning sound effects exactly where they would
be heard in real life. For best results, Dolby Digital EX should be
used with movie soundtracks recorded with Dolby Digital Surround EX which contain a digital flag that will automatically
activate this feature. However, for titles released prior to late
2001, this feature has to be activated manually.
Although only Dolby Digital soundtracks incorporate a separate
low frequency channel, connecting a subwoofer will also improve
deep bass performance in the other surround modes.
The indication “LFE” appears in the display when a signal is being
input for this channel.
DTS-ES
DTS-ES (Digital Theater System-Extended Surround) presents 6.1
channels surround system with additional Surround Back channel
which evolved from the conventional 5.1 channels surround
system. DTS-ES format that was recorded in DVD, CD or LD
comprises of two modes. DTS-ES Discrete 6.1 produces the
discrete surround back which is completely independent and DTSES Matrix 6.1 produces the surround back which synthesised
within the left and right surround channels using matrix technology. DTS-ES has perfect compatibility with the conventional 5.1
channels surround system. 6.1 channels surround with an additional surround back presents a more natural presence and surround effects by increasing the impression of the sound image
from back. Programs which are recorded using DTS-ES technology consist of information flags which will be able to control the
Discrete and Matrix mode. Thus, it can automatically select the
best matched mode.
Dolby PRO LOGIC IIx and Dolby PRO LOGIC II
Neo:6
Dolby Pro Logic II was designed specifically to provide a new
sense of spatiality, directionality and articulation of sounds from
Dolby Surround encoded sources (such as video and Laserdisc
software marked
). This is achieved with an intelligent, built-in feedback logic design, a matrix surround decoding
and the decoding of stereo, full bandwidth surround outputs.
DOLBY PRO LOGIC IIx enhanced DOLBY PRO LOGIC II’s features.
It creates 6.1 channel and 7.1 channel surround sound from stereo
or 5.1 channel signals. This feature provides you an astonishing
ambience effect which makes you feel you are surrounded by
natural sound. Especially 7.1 channel surround sound can produce
real back sound from Surround Back speakers.
Neo:6 is a new technology which was developed by DTS. It can
produce high grade 6 channels surround with an astonishing
fidelity from 2 channels content. Neo:6 has 2 modes, “CINEMA”
mode is for movie playback and “MUSIC” mode is for music
playback.
The PRO LOGICIIx modes programmed into this model are
“MOVIE”, “MUSIC” and “GAME”. The PRO LOGIC II modes
programmed into this model are “MOVIE”, “MUSIC”, “GAME”
and “PRO LOGIC”. The “MOVIE” mode has preset characteristics to produce a calibrated, high-level surround sound playback
while the “MUSIC” mode has user-adjustable characteristics to
offer the three optional controls, like “Dimension”, “Center Width”
and “Panorama” modes to allow optimization of the soundfields
as desired. The “Dimension” control allows the user to gradually
adjust the soundfield either towards the front or towards the rear;
the “Center Width” control allows various adjustment of the leftcenter-right speakers’ balance; the “Panorama” mode extends
the front stereo image to include the surround speakers for an
exciting “wraparound” effect with side wall imaging.
The “GAME” mode provides surrounded and exciting sound
when you enjoy game or TV. Especially in PRO LOGIC IIx “GAME”
mode, base sound not only from Front and Center but also from
Surround channel is added to Subwoofer. This provides even
more dynamic surround effects.
DTS 96/24
DTS 96/24 made it possible to achieve a wide frequency range of
over 40 kHz by increasing the sampling frequency to 96 or 88.2
kHz. Moreover, DTS 96/24’s ability of 24 bit resolution offers the
same frequency band and dynamic range as 96 kHz/24 bit PCM.
DTS 96/24 is, as with conventional DTS Surround, compatible with
multi-channels. Therefore, sources recorded using DTS 96/24
technologies can be played in high sampling frequency, multichannel audio with ordinary DVDs and CDs.
DTS has a “.1” or “LFE” channel.
The indication “LFE” appears in the display when a signal is being
input for this channel.
Note
LFE = Low Frequency Effects. This channel delivers separate nondirectional bass signals to the subwoofer for more dynamic deep
bass sound effects.
31 EN
*5455/30-37/EN
31
04.6.16, 2:17 PM
Ambience effects
THX
THX Surround EX mode
Movie soundtracks are mixed in special movie theatres called dubbing stages and are designed to be played back in movie theatres with
similar equipment and conditions. This same soundtrack is then
transferred directly onto Laserdisc, VHS tape, DVD, etc., and is not
changed for playback in a small home theatre environment.
THX engineers developed patented technologies to accurately translate the sound from the movie theatre environment into the home,
correcting the tonal and spatial errors that occur. Activate THX
whenever watching a movie that was intended for the playback in a
Cinema. On this product, when the THX indicator is on, the following
THX features are automatically added in movie playback modes (e.g.
Dolby Digital+THX, DTS+THX, THX Surround EX, etc):
THX Surround EX-Dolby Digital Surround EX is a joint development of
Dolby Laboratories and the THX division of Lucasfilm Ltd.
In a movie theatre, film soundtracks that have been encoded with
Dolby Digital Surround EX technology are able to reproduce an extra
channel which has been added during the mixing of the program. This
channel, called Surround Back, places sounds behind the listener in
addition to the currently available front left, front center, front right,
surround right, surround left and subwoofer channels. This additional
channel provides the opportunity for more detailed imaging behind
the listener and brings more depth, spacious ambience and sound
localization than ever before.
Re-equalization (Re-EQ)
The tonal balance of a film soundtrack will be excessively bright and
harsh when played back over audio equipment in the home because
film soundtracks were designed to be played back in large movie
theatres using very different professional equipment. Re-Equalization restores the correct tonal balance for watching a movie soundtrack
in a small home environment.
Movies that were created using the Dolby Digital Surround EX
technology, when released into the home consumer market may
exhibit a Dolby Digital Surround EX logo on the packaging. A list of
movies created using this technology can be found on the Dolby web
site at http://www.dolby.com.
Only receiver and controller product bearing the THX Surround EX
logo, when in the THX Surround EX mode, faithfully reproduce this
new technology in the home.
Timbre Matching
The human ear changes our perception of a sound depending on the
direction from which the sound is coming. In a movie theatre, there
is an array of surround speakers so that the surround information is
all around you. In a home theatre, you use only two speakers located
to the side of your head. The Timbre Matching feature filters the
information going to the surround speakers so that they more closely
match the tonal characteristics of the sound coming from the front
speakers. This ensures seamless panning between the front and
surround speakers.
This product may also engage the “THX Surround EX” mode during
the playback of 5.1 channel material that is not Dolby Digital Surround
EX encoded. In such case the information delivered to the Surround
Back channel will be program dependent and may or may not be very
pleasing depending on the particular soundtrack and the taste of the
individual listener.
DSP mode
Adaptive Decorrelation
In a movie theatre, a large number of surround speakers help create
an enveloping surround sound experience, but in a home theatre
there are usually only two speakers. This can make the surround
speakers sound like headphones that lack spaciousness and envelopment. The surround sounds will also collapse into the closest speaker
as you move away from the middle seating position. Adaptive
Decorrelation slightly changes one surround channel's time and
phase relationship with respect to the other surround channel. This
expands the listening position and creates - with only two speakers
- the same spacious surround experience as in a movie theatre.
THX Select
Before any home theatre component can be THX Select certified, it
must incorporate all the features above and also pass a rigorous
series of quality and performance tests. Only then can a product
feature the THX Select logo. Hundreds of parameters in both the
digital and analog domain are tested and required to meet very
specific high quality standards which is your guarantee that the Home
Theatre products you purchase will give you superb performance for
many years to come. THX Select requirements cover every aspect of
the product including pre-amplifier and power amplifier performance
and operation.
The DSP mode lets you add the atmosphere of a live concert or hall
to almost any type of program source. These modes are particularly
effective when used with stereo program sources, like CD, television,
and FM radio. You might enjoy trying the ARENA, JAZZ CLUB,
THEATER, STADIUM or DISCO mode the next time you watch a
concert or sporting event!
What's DSP mode?
DSP stands for Digital Signal Processor.
The way a sound is heard in an actual environment depends on a
variety of different factors. One of the most important is reverberation
(the act of decaying elements of sound echoing in various places).
The DSP modes produce the feeling of presence by using the DSP to
create reverberation, without spoiling the sound quality of the original
signal.
DVD 6-channel mode
Using a DVD player or the like equipped with six (5.1) output channels
and the receiver, you can enjoy multi-channel encoded DVD source
material in all its splendor. Since the source signals are digital and
each channel is input independently, the resulting sound quality,
sense of spaciousness, and dynamic range are superb.
The indication "6CH INPUT" appears in the display during DVD 6channel mode selection.
32 EN
*5455/30-37/EN
32
04.6.16, 2:17 PM
Ambience effects
Surround play
The DTS compatible models can reproduce a CD, DVD, or LD carrying the
DTS mark.
DOLBY DIGITAL can be used when playing DVD or LD software bearing
the
mark and DOLBY DIGITAL format digital broadcasts (etc.).
DOLBY PRO LOGIC can be used when playing video, DVD, or LD
mark.
software bearing the
THX DSP STEREO INPUT MODE
Input Selector
LISTEN MODE
Input
Selector
DSP Mode
Stereo
Listen Mode 5/ ∞
Input Mode
THX
Preparations
• Turn ON related components.
• Complete “Preparing for surround sound” (speaker settings). (
• Use the Input Selector keys to select the component you wish to play
back with surround sound.
• Use the INPUT MODE key to select the input mode (analog or digital)
for the source you wish to play back.
8
• Noise will be produced when a DTS source is played by selecting the
analog input.
1 Start playing the video software.
2 Use the LISTEN MODE knob or Listen Mode 5/ ∞ keys to
select the listening mode.
When the DOLBY DIGITAL or DOLBY DIGITAL EX signal is
input :
1 DOLBY DIGITAL
: DOLBY DIGITAL surround.
(DOLBY DIGITAL indicator lights up.)
2 DOLBY D EX
: DOLBY DIGITAL EX surround.
(DOLBY DIGITAL indicator lights up.)
3 ŸD+PLIIx MOVIE : DOLBY DIGITAL+PRO LOGIC IIx
surround MOVIE mode.
(DOLBY DIGITAL and PRO LOGIC
indicators light up.)
4 ŸD+PLIIx MUSIC : DOLBY DIGITAL+PRO LOGIC IIx surround
MUSIC mode.
(DOLBY DIGITAL and PRO LOGIC
indicators light up.)
5 PLIIx MOVIE
: PRO LOGIC IIx surround MOVIE mode.*
(DOLBY DIGITAL and PRO LOGIC
indicators light up.)
6 PLIIx MUSIC
: PRO LOGIC IIx surround MUSIC mode.*
(DOLBY DIGITAL and PRO LOGIC
indicators light up.)
7 PLIIx GAME
: PRO LOGIC IIx surround GAME mode.*
(DOLBY DIGITAL and PRO LOGIC
indicators light up.)
8 PLII MOVIE
: PRO LOGIC II surround MOVIE mode.*
(DOLBY DIGITAL and PRO LOGIC
indicators light up.)
9 PLII MUSIC
: PRO LOGIC II surround MUSIC mode.*
(DOLBY DIGITAL and PRO LOGIC
indicators light up.)
0 PLII GAME
: PRO LOGIC II surround GAME mode.*
(DOLBY DIGITAL and PRO LOGIC
indicators light up.)
- PRO LOGIC
: PRO LOGIC II surround PRO LOGIC mode.*
(DOLBY DIGITAL and PRO LOGIC
indicators light up.)
= STEREO
: Normal stereo playback.
(DOLBY DIGITAL and STEREO indicators
light up.)
(* This mode can be selected only when 2 channel stereo signal
comes in.)
When you select DOLBY DIGITAL
“DOLBY DIGITAL” will be displayed.
L
The listening mode settings are stored separately for each input. If
the input mode is set to full auto (“AUTO DETECT” lights), the
receiver selects the optimal listening mode automatically based on
the type of input signal and the speaker settings.
Each turn of the LISTEN MODE knob or press of the Listen Mode
5/ ∞ keys switches the setting as listed below.
The listening mode settings are different depending on the type
of input signal.
Dolby Digital Surround EX compliant disc :
Dolby Digital Surround EX compliant disc contains identification
signals. When you choose FULL AUTO during “Input mode settings” (8), this amplifier detects the identification signals and
selects an optimum LISTEN mode automatically.
Sometimes we find some discs which are Dolby Digital Surround EX
compliant discs but do not contain the identification signals. In this
case, select one of the LISTEN modes which are for 6.1 or 7.1
channel surround mode.
SL
C SW R
LFE
SB
SP
MUTE
A B
CLIP
DTS. DOLBY DIGITAL STEREO
OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC LOUDNESS
ANALOG
96kHzfs
COAXIAL
NEO:6
CSII
THX
Surround EX
RDS
RTY
AUTO
MEMO
STEREO
TUNED
SR
When the DTS or DTS-ES (matrix or discrete) signal is input :
1 DTS-ES Mtrx 6.1 : DTS-ES MATRIX 6.1 channel surround.
(DTS and MATRIX indicators light up.)
2 DTS-ES Dscrt 6.1 : DTS-ES DISCRETE 6.1 channel surround.
(DTS and DISCRETE indicators light up.)
3 DTS
: DTS 5.1 channel surround.
(DTS indicator lights up.)
4 DTS+NEO:6 Cin : DTS+NEO:6 surround CINEMA mode.
(DTS and NEO:6 indicators light up.)
5 NEO:6 CINEMA : NEO:6 surround CINEMA mode.*
(DTS and NEO:6 indicators light up.)
6 NEO:6 MUSIC
: NEO:6 surround MUSIC mode.*
(DTS and NEO:6 indicators light up.)
7 DTS 96/24
: DTS 96/24 playback mode.
(DTS indicator lights up.)
8 STEREO
: Normal stereo playback.
(DTS and STEREO indicators light up.)
(* This mode can be selected only when 2 channel stereo signal
comes in.)
Continued to next page.
33 EN
*5455/30-37/EN
33
04.6.16, 2:17 PM
Ambience effects
When the analog signal or the digital signal (except for
DOLBY DIGITAL or DTS signal) is input :
1 PLIIx MOVIE
2 PLIIx MUSIC
3 PLIIx GAME
4 PLII MOVIE
5 PLII MUSIC
6 PLII GAME
7 PRO LOGIC
8 NEO:6 CINEMA
9 NEO:6 MUSIC
0 STEREO
: PRO LOGIC IIx surround MOVIE mode.
(PRO LOGIC indicator lights up.)
: PRO LOGIC IIx surround MUSIC mode.
(PRO LOGIC indicator lights up.)
: PRO LOGIC IIx surround GAME mode.
(PRO LOGIC indicator lights up.)
: PRO LOGIC II surround MOVIE mode.
(PRO LOGIC indicator lights up.)
: PRO LOGIC II surround MUSIC mode.
(PRO LOGIC indicator lights up.)
: PRO LOGIC II surround GAME mode.
(PRO LOGIC indicator lights up.)
: PRO LOGIC II surround PRO LOGIC mode.
(PRO LOGIC indicator lights up.)
: NEO:6 surround CINEMA mode.
(NEO:6 indicator lights up.)
: NEO:6 surround MUSIC mode.
(NEO:6 indicator lights up.)
: Normal stereo playback.
(STEREO indicator lights up.)
• Dolby Digital or DTS signal having more channels than the maximum
number of playback channels available using this model’s current
settings is input, downmixing is performed to match the number of
available channels.
3 DSP mode (Digital Signal Processor).
DSP can produce these effects without spoiling the sound quality of
the original music or video source.
This mode can be selected when digital signals other than DOLBY
DIGITAL or DTS, or analog signal come in.
1 Pressing the DSP key or DSP Mode key will display the
current DSP MODE status.
2 Each press of the key will switch to the next status as shown
bellow:
1
2
3
4
5
ARENA
JAZZ CLUB
THEATER
STADIUM
DISCO
:
:
:
:
:
DSP surround ARENA mode.
DSP surround JAZZ CLUB mode.
DSP surround THEATER mode.
DSP surround STADIUM mode.
DSP surround DISCO mode.
• The DSP mode selection is displayed for approximately 3 seconds.
• THX functions when the display segment is turned ON.
• THX Sur EX ON and THX Sur EX AUTO will not be available if
surround back speakers are turned OFF.
• The THX setting differs depending on the input selector.
• When PL IIx MUSIC, PL IIx GAME, PL II MUSIC, PL II GAME, NEO:6
MUSIC, ACTIVE EQ or SPEAKER EQ is ON, THX function will not
be effective.
5 Adjust the volume.
Switching the LISTEN mode to STEREO temporarily
Pressing the STEREO key changes the currently selected LISTEN mode
into STEREO. It will be changed back to the original LISTEN mode by
pressing the STEREO key again.
• If the power is turned off and turned back on, or the input selector is
switched to another and switched back, the LISTEN mode will be back
to the original one.
Notes
• Depending on the type of the signal or speaker setting, some listening
modes cannot be selected.
• When playback is started, the sound may be cut or interrupted before
the input source is confirmed as Dolby Digital.
• To enjoy Dolby Digital surround (as well as all the other listening modes)
from a single component, be sure to use a Dolby Digital compatible
source component.
• Dialogue Normalization (Dial Norm) is a feature of Dolby Digital. It is able
to automatically maintain the overall audio output level constant.
L
SL
C
LFE
R
SP
MUTE
A B
CLIP
DTS. DOLBY DIGITAL STEREO
OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC LOUDNESS
ANALOG
96kHzfs
COAXIAL
SR
THX
Surround EX
RDS
RTY
When playing some Dolby Digital sources, you may see in the display
a message "DIALNORM OFFSET xxdB". This is because some
soundtracks may be recorded either louder or quieter than normal. The
xx number shows by how much.
For example, if the message says “DIALNORM OFFSET +4dB” you
know that this particular recording was encoded 4dB louder than
normal. If you wish, you can turn down the volume control by 4dB to
keep the playback level consistent.
This mode creates a home theater environment which is able to
reproduce a cinema surround sound system featuring improved
special representation and acoustic imaging of surround channels by
translating THX Surround EX technology.
Press the THX key to switch the following setting :
1 THX Sur EX AUTO : THX Surround EX function is turned ON
when Dolby Digital Surround EX signal is
detected.
(THX indicator lights up.)
2 THX Sur EX ON
: THX Surround EX function is turned ON
when Dolby Digital 5.1ch signal is
detected.
(THX indicator lights up.)
3 THX ON
: THX mode is turned ON.
(THX indicator lights up.)
4 THX OFF
: THX mode is turned OFF.
(THX indicator goes off.)
34 EN
34
CSII
AUTO
MEMO
STEREO
TUNED
4 THX mode.
*5455/30-37/EN
NEO:6
04.6.16, 2:17 PM
Ambience effects
DVD 6-channel playback
Convenient functions
Using a DVD player or the like equipped with six (5.1) output channels and
the receiver, you can enjoy surround sound playback.
Connecting a DVD player which can decode the surround signal itself is
also acceptable.
STEREO DIMMER
MULTI CONTROL
VOLUME
CONTROL
INPUT MODE
SOUND
LISTEN MODE
TUNER
DVD/6CH
(Multi %/ fi,
@ / #)
DVD/6CH
Sound
Dimmer
VOL
Listen Mode5/ ∞
/
Input Mode
Stereo
Adjusting the sound
You can make further adjustments to the sound while listening to
playback in the surround mode.
Preparations
• Connect your DVD player to the DVD/6CH jacks of the receiver.
• Turn on all other components that will be used.
• Complete “Preparing for surround sound”.
(
1 Press “DVD/6CH” as the input source.
2 Select "6CH INPUT" by pressing the INPUT MODE key.
1 For the remote control, press and hold the TUNER key for more
than 3 seconds to switch to receiver mode.
∨ keys or @/# keys
2 Press the SOUND key and then use the ∧/∨
until the desired item appears in the display.
∨ keys or @/# keys, the menu
Each time you press the ∧ /∨
changes as follows:
Note that some items are not displayed in certain modes.
• If speaker system B is on when “6CH INPUT” is selected as the
input source, it switches off and speaker system A turns on
automatically.
1 CNTR (Center Speaker level adjustment)*
2 SR (Right Surround Speaker level adjustment)*
3 SBR (Surround Back Right Speaker level adjustment)*
4 SBL (Surround Back Left Speaker level adjustment)*
5 SL (Left Surround Speaker level adjustment)*
6 SUBW (Subwoofer level adjustment)*
7 INPUT (Input level adjustment - analog mode only)
™
8 MIDNIGHT (Midnight mode ON/OFF - Dolby Digital and DTS
mode only)
9 PANORAMA (Panorama mode ON/OFF)**
0 DIMENSION (Dimension adjustment)**
- CENTER WIDTH (Center width adjustment)**
= DUAL MONO (Dual Mono selection - Dolby Digital mode only)
3 Start playback of the DVD software.
4 Adjust the volume.
• It is not possible to adjust the volume level or sound quality (SET
UP, SOUND, LISTEN MODE, ACTIVE EQ, SPEAKER EQ, STEREO, DSP, LOUDNESS and TONE key will not be functional) of
the channels separately when the receiver is in the 6CH INPUT
mode. Adjust the volume with the controls of the DVD player.
For the powered subwoofer, you can adjust the volume of the
subwoofer using the subwoofer’s own volume control.
*
**
The adjustment is only temporary for the current input selection.
The value will return automatically to the original setup value when
the power is turned on/off or when the input selector is changed.
Pro Logic IIx Music and Pro Logic II Music mode only.
3 Use the MULTI CONTROL knob or Multi (%/fi) keys to adjust the
setting as desired.
• The adjustment item is displayed for approximately 20 seconds.
35 EN
*5455/30-37/EN
35
04.6.16, 2:17 PM
Ambience effects
Midnight mode (Dolby Digital and DTS mode only)
When watching movies at night , you might not be able to raise the
volume as loud as normal. Midnight mode compresses the dynamic
range of previously specified heavy sound passage of the Dolby Digital
and DTS sound track (like scenes with sudden increases in volume) to
minimize the difference in volume between the scenes with heavy
sound passage and scenes with normal sound passage. This makes it
easy to hear all of the sound track, even when listening at low volumes.
∨ keys or @/# keys until
1 Press the SOUND key, then press the ∧/∨
“MIDNIGHT” appears on the display.
• This can be selected only if CD/DVD, DVD/6CH, VIDEO 2 or VIDEO3 is
selected as the source and the listen mode is set to “DOLBY DIGITAL”
or “DTS”.
2 Use the MULTI CONTROL knob or Multi (%/fi) keys to select
the ON or OFF setting.
L
C
LFE
SL S
SB
R
SP
MUTE
A B
CLIP
DTS. DOLBY DIGITAL STEREO
OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC LOUDNESS
ANALOG
96kHzfs
COAXIAL
NEO:6
CSII
THX
Surround EX
When listening to music with certain recordings, you will also be able to
achieve a suitable balance from all the speakers by adjusting the
dimension mode.
∨ keys or @/# keys until
1 Press the SOUND key, then press the ∧/∨
“DIMENSION” appears on the display.
2 Use the MULTI CONTROL knob or Multi (%/fi) keys to adjust
the soundfield towards the rear or the front.
Soundfield is adjusted towards the front.
L
R
SP
MUTE
A B
CLIP
DTS. DOLBY DIGITAL STEREO
OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC LOUDNESS
ANALOG
96kHzfs
COAXIAL
NEO:6
CSII
RDS
RTY
THX
Surround EX
AUTO
MEMO
STEREO
TUNED
LFE
RDS
RTY
AUTO
MEMO
STEREO
TUNED
SR
Dimension mode (Pro Logic IIx Music and Pro Logic II Music
mode only)
Soundfield is in neutral position.
L
R
SP
MUTE
A B
CLIP
DTS. DOLBY DIGITAL STEREO
OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC LOUDNESS
ANALOG
96kHzfs
COAXIAL
NEO:6
CSII
• The adjustment item is displayed for approximately 20 seconds.
• Some Dolby Digital or DTS software may not be compatible with the
Midnight mode.
S
RDS
RTY
THX
Surround EX
AUTO
MEMO
STEREO
TUNED
LFE
SB
Soundfield is adjusted towards the rear.
Panorama mode (Pro Logic IIx Music and Pro Logic II Music
mode only)
L
R
SP
MUTE
A B
CLIP
DTS. DOLBY DIGITAL STEREO
OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC LOUDNESS
ANALOG
96kHzfs
COAXIAL
NEO:6
CSII
RDS
RTY
THX
Surround EX
AUTO
MEMO
STEREO
TUNED
LFE
When listening to music, you will be able to enjoy the “wraparound”
sound effect when you adjust the panorama mode.
∨ keys or @/# keys until
1 Press the SOUND key, then press the ∧/∨
“PANORAMA” appears on the display.
Center Width mode (Pro Logic IIx Music and Pro Logic II
Music mode only)
2 Use the MULTI CONTROL knob or Multi (%/fi) keys to
select PANORAMA ON or OFF.
Center width adjustment allows you to enjoy an enhanced sound when
listening to music through center image from only Center Speaker, or
Left and Right Speakers or various combinations adjustments.
1 PANORAMA ON : PANORAMA mode is ON.
2 PANORAMA OFF : PANORAMA mode is OFF.
L
R
SP
MUTE
A B
CLIP
DTS. DOLBY DIGITAL STEREO
OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC LOUDNESS
ANALOG
96kHzfs
COAXIAL
S
NEO:6
CSII
THX
Surround EX
RDS
RTY
AUTO
MEMO
STEREO
TUNED
LFE
SB
∨ keys or @/# keys until
1 Press the SOUND key, then press the ∧/∨
“CENTER WIDTH” appears on the display.
• The CENTER WIDTH indication scrolls across the display.
• When the center speaker is switched OFF, this mode will not be
effective.
2 Use the MULTI CONTROL knob or Multi (%/fi) keys to adjust
the left-center-right output.
Center image will be heard from Center Speaker only.
L
R
SP
MUTE
A B
CLIP
DTS. DOLBY DIGITAL STEREO
OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC LOUDNESS
ANALOG
96kHzfs
COAXIAL
NEO:6
CSII
THX
Surround EX
S
RDS
RTY
AUTO
MEMO
STEREO
TUNED
LFE
SB
Center image will be heard from Left and Right Speakers only.
L
R
SP
MUTE
A B
CLIP
DTS. DOLBY DIGITAL STEREO
OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC LOUDNESS
ANALOG
96kHzfs
COAXIAL
S
NEO:6
CSII
THX
Surround EX
RDS
RTY
AUTO
MEMO
STEREO
TUNED
LFE
SB
• When in other position, center image from Center Speaker, Left and
Right speakers can be heard simultaneously with various combinations.
36 EN
*5455/30-37/EN
36
04.6.16, 2:18 PM
Ambience effects
Dual Mono mode (Dolby Digital mode only)
96kHz LPCM playback
When the Dolby Digital source have Multiplex sound, you can select
Main / Sub sound for Audio output.
The receiver is compatible with the 96kHz LPCM playback. To play a
96kHz DVD, set the listen mode other than DSP mode.
∨ keys or @/# keys until
1 Press the SOUND key, then press the ∧/∨
“DUAL MONO” appears on the display.
• This can be selected only if CD/DVD, DVD/6CH, VIDEO 2 or VIDEO
3 is selected as the source, and the input signal is set to “Dolby
Digital”.
• In FULL AUTO input mode and the listen mode is set to DSP mode, the
listen mode will automatically be STEREO.
• When in DIGITAL MANUAL input mode and the listen mode is set to
DSP mode, “96kHz LPCM” will appear in the display and no sound can
be heard from the speakers.
Use the LISTEN MODE knob or STEREO key to select STEREO mode
to output sound from the speakers.
2 Use the MULTI CONTROL knob or Multi (%/fi) keys for the
following selection.
1
2
3
4
Main
Sub
Main + Sub
Stereo
:
:
:
:
Multiplex Main channel output.
Multiplex Sub channel output.
Multiplex Main + Sub channel output.
Main channel from the left speaker. / Sub
channel from the right speaker.
OPTICAL 6CH INPUT
LFE
• The adjustment item is displayed for approximately 20 seconds.
Display dimmer adjustment
The dimmer function lets you select the brightness of the receiver's
display. You might find this useful if you darken your room to watch
movies or listen to music.
Each time you press the DIMMER key, the display brightness
changes among the three available settings.
Select the brightness level you find most pleasing.
L
R
SP
MUTE
A B
CLIP
DTS. DOLBY DIGITAL
OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ.
ACTIVE EQ.
MATRIX
DSP MODE DISCRETE PRO LOGIC LOUDNESS
ANALOG
96kHzfs
COAXIAL
R
L
R
CSII
THX
Surround EX
RDS
RTY
DOLBY DIGITAL
SP
L
NEO:6
AUTO
MEMO
STEREO
TUNED
LFE
A
PRO LOGIC
DOLBY DIGITAL STEREO
SP
A
PRO LOGIC
37 EN
*5455/30-37/EN
37
04.6.16, 2:18 PM
Basic remote control operations for other components
The remote control supplied with this receiver is also capable
of controlling components from a variety of manufacturers
once you register the appropriate setup codes into the
remote control unit.
Low battery warning
Replace all two batteries with new ones when you notice a shortening
of the distance from which the remote control will operate.The
remote control is designed to retain setup codes in memory while
you change batteries.
Registering setup codes for other components
Source
keys
• If performed correctly,
will blink twice.
• Point the remote control at the component and press SRC Power
key once. It should turn on/off but if it does not, repeat step 2 to 4
• If the component still does not work, try searching for the code.
5 Repeat steps 2 to 4 to register additional components until
all components have been registered.
Note
Although each setup code is designed to work with a number of
different models, certain codes may not work with some models.
(Also, certain codes may only operate some of the functions available
on a given model.)
Searching for your codes
SRC Power
If your component does not respond after trying all the codes listed for
your component, or if your component is not listed at all, try searching
for your code.
For example, to search for code for your TV:
Numeric keys
1 Press the TV key once. Next, press and hold the Learn key
until
blinks twice, then release the Learn key.
Learn
1 Find the setup code of the component to be registered.
• Refer to the setup code lists to find the setup code for the
component to be registered.
q
Example: To register a DVD made by KENWOOD, you would enter
“0534”.
Input
Component
Maker
Code
Key
DVD/6CH
DVD player
KENWOOD
0534
DVD 6CH
2 Press the numeric key to enter 9 , 9 , 1.
• will blink twice.
3 Point the remote control at the TV and slowly alternate
between pressing the TV Power and TV key.
• Stop when the TV turns on/off.
• In the search mode, the remote control will send IR codes from its
library to the selected device, starting with the most popular code
first.
4 Press the Learn key once to lock in the code.
5 To search for the codes of your other components, repeat
CD/DVD
CD and MD (Kenwood)
steps 1 through 4, but substitute the appropriate key (i.e.,
DVD/6CH, CD/DVD, VID1, VID2, VID3, TV, MD/TAPE, AV AUX,
PHONO, SRC Power).
MD/TAPE
Cassette deck (Kenwood)
• PHONO key has to be re-assigned to another key before a setup
VID1 , AV AUX
VCR and PVR
Source key
Other components
DVD/6CH
DVD
code can be programmed.
VID2
Cable and DTV decoder
VID3
Satellite
PHONO
Additional key for re-assigning
TV
TV/VCR combo, TV/DVD combo, TV
2 Press the Source keys (DVD/6CH, CD/DVD, VID1, VID2, VID3,
TV, MD/TAPE, AV AUX, PHONO).
• PHONO key has to re-assigned to another key before a setup
code can be registered.
q
• While in Tuner mode, setup code function will not be available.
3 Press and hold the Learn key until the
blinks twice, then
release the Learn key.
4 Press the Numeric keys to enter the four-digit code for the
component to be registered.
Checking the codes
If you have setup the remote control using the procedures described in
“Searching for your codes”, you may need to find out which four-digit
code is operating your equipment:
For example, to find out which code is operating your TV:
1 Press the TV key once. Next, press and hold the Learn key
until
blinks twice, then release the Learn key.
2 Press the numeric key to enter 9 , 9 , ).
• will blink twice.
3 To view the code for the first digit, press “1” once. Wait for 3
seconds, counts the number of times
and write down that number.
• If a code digit is “0”, the
38 EN
*5455/38-52/EN
38
04.6.16, 4:28 PM
blinks (e.g., blinks=3)
will not blink.
Basic remote control operations for other components
Operating other components
4 Repeat step 3 three more times for the remaining digits. Use
“2” for the second digit, “3” for the third digit, and “4” for the
fourth digit.
5 To check the codes of your other components, repeat steps
1 through 4 , but substitute the appropriate key (i.e.,
DVD/6CH, CD/DVD, VID1, VID2, VID3, TV, MD/TAPE, AV AUX,
PHONO) for the component you are checking.
•
•
This operation lets you operate the registered components.
Source
keys
SRC Power
As suggested earlier on, write down each of the four-digit code.
PHONO key has to be re-assigned to another key before a setup
code can be programmed.
Re-assigning device keys
The remote control can be setup to control second TV or VCR, or any
combination of eight home entertainment components.
For example, to control the operation of two different VCR using the
remote control, the user need to re-assign the unused VID2 key to
operate the second VCR(VID1) as follows:
1 Press and hold the Learn key until
blinks twice, then
release the Learn key.
• Pressing the source keys also changes the input selector on the
receiver.
2 Press the SRC Power key.
• To return to the receiver operation mode, press the TUNER key for
more than 3 seconds.
3 Press the operation keys you desire.
2 Press the Numeric key to enter 9 , 9 , 2.
• will blink twice.
y
The remote control mode remains at the selected input. If you
wish to operate another component, repeat step 2 or 3.
3 Press VID1 key once, then press the VID2 key once.
• The user now can operate VID2 as a second VCR along with VID1.
• Refer to the table in the previous page for the combination of
source keys and the other components assignment.
1 Use the Source keys to select the component you desire.
°
Resetting the Remote Control
• To initialize the remote control, press the Learn key until blinks
twice. Then press the Numeric key to enter 9, 8, 1.
will
blink twice.
4 To re-assign other device keys, repeat steps 1 through 3 by
substituting the key sequence from the below chart for the
most popular components:
To re-assign key
Sequence
TV as 2nd VID1 key
TV as 2nd VID2 key
TV as 2nd CD/DVD key
TV back to TV key
VID1 as 2nd TV key
VID1 as 2nd VID2 key
VID1 as 2nd CD/DVD key
VID1 back to VID1 key
Perform
Learn
Learn
Learn
Learn
Learn
Learn
Learn
Learn
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
2
2
2
2
2
2
2
2
VID1
VID2
CD/DVD
TV
TV
VID2
CD/DVD
VID1
TV
TV
TV
TV
VID1
VID1
VID1
VID1
5 To clear the re-assignment and reset the remote control to its
original operation mode:
1 Press and hold the Learn key until
the Learn key.
blinks twice, then release
2 Press the numeric key to enter 9 , 9 , 2.
3 Press VID2 key twice.
•
•
•
When a re-assignment is done, will blink twice to confirm
your choice. At that time, you will need to program the remote
control in order to control the new component.
If an invalid key sequence is entered,
blink once and return to
normal operation.
When in Tuner mode, re-assignment is not available.
39 EN
*5455/38-52/EN
39
04.6.16, 4:28 PM
Basic remote control operations for other components
Storing the remote control code of the other
components
The remote control unit can store the remote control code of the other
components and you can operate the other components from the remote
control unit. The remote control code is stored on the key or memory of
the remote control unit.
Storing on the key
You can store the remote control code to the key as shown below:
6 From the remote control unit of the other source, press the key
that you want to store.
• The remote control code is sent to the remote control unit.
• “OK” appears when finished.
• If the code cannot be stored after a few attempts, “ERROR” will
appear. Repeat from step 2 onwards.
7 The remote control code is stored on the key of this remote
control unit.
8 Repeat step 4 to 6 to store additional components until all
LCD
Source keys
the desired components are stored.
VID1
TUNER
VID2
VID3
TV
4
6
P. Call
Enter
1 Press and hold the Learn key for 3 seconds until
then release the Learn key.
7
Multi
1
8
0
+ 10
Return
Disc Skip
9
Return
Guide
¡Rewind
1Fast forward
3/8Play/Pause
2Info/Flip
Menu
Disc Sel.
OSD
Menu
+
TV
VOL
+
–
TV Input
Tune –
Dimmer
Bass
Boost
Band
Tune +
Auto
Top Menu
Info / Flip
Setup
Loudness
Listen Mode
Active
EQ
blinks twice to indicate that the stored remote control code are
deleted.
VOL
Sound
–
–
3 Press the Source key, then press the stored key twice until
blinks twice.
+
Tone
CH
4
DSP
Mode
Stereo
Speaker
EQ
THX
Input
Mode
Learn
7Stop
Learn
1 Point the infrared ray system part of another remote control
unit to the remote sensor of the remote control unit.
Remote control
unit of the other
source.
Infrared ray system part
2 Press and hold the Learn key for 3 seconds until
blinks
twice, then release the Learn key.
3 Press the numeric key to enter 9, 7, 5.
4 Press any of the source keys (PHONO, VID1, VID2, VID3, DVD/
6CH, AV AUX, CD/DVD, MD/TAPE, TV ) to select the input of the
desired remote control unit.
• While in Tuner mode, learning code function will not be available.
5 Press the desired key of the remote control unit.
• “LEARN” appears on the display.
40 EN
*5455/38-52/EN
40
blinks twice,
2 Press the numeric key to enter 9, 7, 6.
•
Mute
Input Sel.
¢
CH +/–
Skip ¢/4
+ 100
OSD
Last / AB
Exit
Disc Skip
Disc Sel.
Page∞/5
TV Mute
Page
blinks twice.
0 To clear the stored remote control code of the other sources:
5
Multi
P. Call
Pow
er
r
we
SR
seconds until
TV
C Po
2
9 To exit the learning mode, press and hold the Learn key for 3
MD
TAPE
POWER
RCVR
3
Numeric keys
CD
DVD
AV AUX
PHONO
SRC Power
DVD
6CH
04.6.16, 4:28 PM
Basic remote control operations for other components
Setup code chart
TV setup codes
Cassette deck setup codes
Maker
Setup codes
Maker
Setup codes
Maker
Setup codes
Kenwood
0070, 0071, 0092, 0183,
0205, 0233, 0234, 0251,
0386
AGB
ASA
Acura
Admiral
Adyson
Aiwa
Akai
0516
0087, 0104, 0802
0009
0087, 0163
0217
0701, 0800
0208, 0361, 0516, 0602,
0708, 1537
0803
0272
0264, 0218, 0493
0009, 0036, 0037, 0218,
0211, 0371, 0581, 0668,
0803, 0805,
0294
0217, 0400
0037, 0009, 0177, 0354,
0371, 0412, 0433, 0516,
0800
0009, 0803
0216, 0217
0218, 0802
0206
0037, 0109
0087, 0206, 0336
0282
0294
0218
0800
0087, 0565
0380
0009, 0218, 0803, 0805,
0010, 0037, 0505, 0512,
0535, 0554
0178
0370, 0486, 0714, 0715
0037
0217
0195, 0200, 0327, 0328,
0535
0218, 0668, 1037
0282
0247
0217
0109, 0196, 0198, 0335
0087
0216
0087
0009, 0036, 0037, 0211,
0218, 0272, 0282, 0294,
0355, 0371, 0374, 0519,
0581, 0668, 0698, 0805,
0803
0074, 0084, 0247, 0800
0216
0247
0036
0009
0037
0037
0087
0009, 0803
0037
Clatronic
Condor
Contec
Continental Edison
Crosley
Crown
0247, 0370
0370
0009, 0036, 0216
0196, 0198, 0399
0074, 0084, 0087
0009, 0037, 0370, 0418,
0579, 0803, 0805
0218
0009, 0037, 0374, 0499,
0805
0218
0037, 0803
0009
0208, 0548
0037, 0072, 0272, 0516,
0800
0009, 0037
0336, 0519
0217
0070, 0087, 0800
0259
0803
0037, 0548
0218
0009
0087, 0361
0037, 0012
0804, 0805
0516
0206
0037, 0073, 0109, 0190,
0193, 0238, 0335, 0560
0009, 0216, 0217, 0247,
0294, 0668, 0802, 0803
0193, 0216, 0361, 0800
0208, 0346
0037, 0070, 0072, 0087,
0104, 0105, 0179, 0346,
0411, 0516, 0800
0104, 0208, 0217, 0303,
0370
0455
0193
0037, 0087
0163, 0247, 0264, 0448
0072, 0206, 0683
0264, 0179, 0294, 0303,
0800
0037, 0043, 0072, 0217,
0516
0218
0009
0163, 0218
0037, 0109, 0178, 0217,
0290, 0377, 0802
0803
0037, 0217, 0036, 0072,
0179, 0371, 0374, 0499,
0634, 0802, 0800, 0805,
0803
0370
0163, 0361, 0804
0037, 0045, 0072, 0208,
0217, 0339, 0516
CD and MD player setup codes
Maker
Setup codes
Kenwood
0028,
0338,
0626,
0826,
1490
0036,
0339,
0677,
0858,
0037,
0340,
0681,
0859,
0190,
0523,
0692,
1059,
Akiba
Akito
Akura
Alba
Allorgan
Amplivision
Amstrad
Anitech
Arcam
Asuka
Atlantic
Audiosonic
Autovox
BPL
BSR
BTC
Baird
Bang & Olufsen
Barco
Basic Line
Baur
Beaumark
Beko
Beon
Binatone
Blaupunkt
Blue Sky
Blue Star
Bondstec
Boots
Brandt
Brionvega
Britannia
Bruns
Bush
CGE
CS Electronics
CTC
Carrefour
Cascade
Cathay
Centurion
Century
Cimline
Clarivox
Cybertron
Daewoo
Dainichi
Dansai
Dayton
De Graaf
Decca
Dixi
Dual
Dual Tec
Dumont
Elbe
Elcatech
Elin
Elite
Elta
Emerson
Erres
ESC
Europhon
Expert
Ferguson
Firstline
Fidelity
Finlandia
Finlux
Fisher
Flint
Forgestone
Formenti
Frontech
Fujitsu
Funai
GEC
GPM
Geloso
Genexxa
GoldStar
Goldhand
Goodmans
Gorenje
Graetz
Granada
41 EN
*5455/38-52/EN
41
04.6.16, 4:28 PM
Basic remote control operations for other components
Setup code chart
TV setup codes (continue)
Maker
Setup codes
Maker
Setup codes
Maker
Setup codes
Grandin
0282, 0610, 0802, 0800,
0803
0070, 0195, 0487, 0535,
0554, 0556, 0587, 0706,
0803, 0901
0009, 0282, 0412, 0803
0037, 0361, 0556, 0802
0516
0093
0009, 0036, 0037, 0179,
0218, 0803, 0804
0282, 0400, 0455
0036, 0043, 0044, 0105,
0109, 0163, 0196, 0198,
0217, 0225, 0548, 0578,
0719, 0730, 0800
0216, 0374
0037, 0264, 0282, 0803
0217, 0264, 0371
0218
0074
0371
0163, 0361, 0548, 0804
0802, 0805
0074, 0084, 0247, 0370,
0418, 0630, 0800
0037
0163
0072, 0516
0037, 0163, 0247, 0361,
0512
0037, 0102, 0217, 0264,
0377
0218
0901
0036, 0053, 0094, 0190,
0192, 0371, 0606, 0653,
0683
0009, 0216, 0217, 0218,
0282, 0803
0163, 0206
0610
0556
0037
0216
0259, 0435
0037, 0803
0087
0009
0805
0037, 0072, 0264, 0294,
0803
0037
0087, 0512, 0802, 0806
0804
0206
0194, 0361
0009, 0037, 0057, 0104,
0105, 0109, 0163, 0217,
0346, 0374, 0480, 0800
0512
0087, 0102, 0247, 0516
0102, 0516
0648
0217, 0264, 0803
Marantz
Marelli
Mark
Matsui
0037, 0556
0087
0037
0009, 0011, 0036, 0037,
0072, 0208, 0211, 0217,
0177, 0272, 0294, 0354,
0355, 0371, 0443, 0487,
0516, 0579
0043
0012, 0037
0668
0009, 0800, 0802, 1037
0337, 0803
0087, 0275, 0367, 0388,
0447, 0535, 0802, 0806
0070, 0487, 0535
0412
0033, 0036, 0087, 0108,
0354, 0512, 0535
0216, 0290, 0291, 0292,
0516, 0609
0009, 0216, 0800, 0803
0800
0556
0170, 0704
0037, 0337
0037, 0087, 0505, 0556
0179, 0803
0037, 0072,0216, 0218,
0264, 0337
0102
0361, 0473, 0480, 0548,
0606, 0631, 0804
0109, 0196, 0198, 0560
0163, 0361, 0800
0433
0037, 0177, 0294, 0355,
0443, 0516, 0655
0072, 0217, 0218, 0264,
0412, 0493, 0800, 0802,
0803
0218
0072, 0157
0010, 0036, 0037, 0217,
0505, 0512, 0535, 0556
0370, 0418, 0802, 0803
0217, 0264
0126, 0163, 0226, 0250,
0367, 0650, 0806, 1650
0216, 0238
0196, 0198
0009
0800
0074, 0084, 0087, 0247
0012, 0037, 0043, 0087,
0193, 0374, 0556
0087
0012, 0037, 0087
0109, 0163, 0166
0697
0516
0009, 0361
0804
0800
Protech
0009, 0037, 0102, 0217,
0247, 0264, 0337, 0418,
0668
0012
0010, 0011, 0037, 0070,
0074, 0084, 0104, 0200,
0327, 0328, 0361, 0505,
0512, 0535
0036
0037
0070
0087
0012, 0037
0087, 0516
0036
0361
0037
0163, 0206, 0264, 0259
0009, 0218, 0264, 0418,
0802, 0803, 0804, 0805
0012, 0037, 0043, 0193
0036, 0217, 0264, 0668,
0804
0010, 0087, 0102, 0177,
0294, 0516
0087, 0109, 0163, 0196,
0198, 0335
0238
0610
0009, 0011, 0033, 0177,
0211, 0264, 0354, 0516
0163, 0194, 0361, 0548
0102, 0516
0009, 0037, 0217, 0264,
0290, 0370, 0556, 0587,
0618, 0644, 0804
0216
0655, 0706
0011, 0036, 0045, 0072,
0104, 0157, 0208, 0339
0361, 0800
0037, 0057, 0218, 0247,
0303, 0336, 0371, 0394,
0668, 0800, 0803, 1137
0163, 0206, 0259, 0411
0036, 0093, 0256, 0901,
1193
0803
0294
0087, 0102, 0516
0037, 0157, 0195, 0200,
0327, 0328, 0535, 0802
0802
0036
0087
0010, 0087, 0102, 0177,
0294, 0516
0696
0163
0208
0037, 0802
0009, 0037
0163, 0208
0010, 0011, 0036, 0505,
0651, 1505, 1651
Grundig
HCM
Hanseatic
Hantarex
Havermy
Hinari
Hisawa
Hitachi
Huanyu
Hypson
ICE
ICeS
IR
ITS
ITT
ITV
Imperial
Indiana
Ingelen
Inno Hit
Interfunk
Intervision
Isukai
JMB
JVC
Kaisui
Kapsch
Karcher
Kathrein
Kendo
Kingsley
Kneissel
Korpel
Korting
Koyoda
Lenco
Leyco
Liesenk & Tter
Loewe
Logik
Luma
Luxor
M Electronic
MTC
Magnadyne
Magnafon
Magnum
Manesth
McMichael
Mediator
Medion
Memorex
Memphis
Metz
Minerva
Minoka
Mitsubishi
Mivar
Multitech
Murphy
Myryad
NEC
NEI
Neckermann
Nesco
Nikkai
Nobliko
Nokia
Nordmende
Oceanic
Onwa
Orion
Osaki
Oso
Osume
Otto Versand
Palladium
Panama
Panasonic
Pathe Cinema
Pathe Marconi
Pausa
Perdio
Philco
Philips
Phoenix
Phonola
Pioneer
Polytron
Prandoni Prince
Profex
Profitronic
Proline
Pye
Quelle
Questa
R-Line
RBM
RFT
Radiola
Radiomarelli
Rank Arena
Rediffusion
Revox
Rex
Roadstar
SBR
SEG
SEI
Saba
Saccs
Sagem
Saisho
Salora
Sambers
Samsung
Sandra
Sansui
Sanyo
Schaub Lorenz
Schneider
Seleco
Sharp
Shintom
Shorai
Siarem
Siemens
Silva
Silver
Singer
Sinudyne
Skysonic
Solavox
Sonitron
Sontec
Sonoko
Sonolar
Sony
42 EN
*5455/38-52/EN
42
04.6.16, 4:28 PM
Basic remote control operations for other components
Setup code chart
VCR setup codes
TV setup codes (continue)
Maker
Setup codes
Maker
Setup codes
Maker
Setup codes
Soundwave
Standard
Stern
Sunkai
Sunstar
Suntronic
Susumu
Sysline
T+A
Tandy
Tashiko
Tatung
0037, 0418
0009, 0217, 0218
0163, 0206, 0259
0294, 0355
0800
0800
0218
0037
0447
0072, 0163, 0217, 0218
0036, 0043, 0217, 0800
0037, 0072, 0217, 0516,
0800
0037, 0698, 0712, 1437
0217, 0247
0250, 0650
0179
0074, 0084, 0101, 0109,
0262, 0335 , 0625
0009
0036, 0206, 0217
0218, 0294, 0800
0803
0216, 0218
0109, 0196, 0198, 0399,
0625,
0037, 0072, 0074, 0084,
0104, 0190, 0192, 0193,
0361, 0499, 0512, 0535,
0505
0282
0036, 0070, 0508, 0243,
0718, 1508
0177, 0243, 0516
0206, 0303, 0804
0192
0102
0037, 0074, 0104, 0105,
2064, 0370, 0346, 0492,
0535, 0802, 0800, 0804
0037
0247
0217
0802
0800
0087, 0163
0217
0037
0102
0036, 0087
0037, 0216
Asa
Aiwa
Akai
Alba
Baird
Bang & olufsen
Blaupunkt
Brandt
Brandt Electronic
Bush
Combitech
Cyrus
Daewoo
De Graaf
Decca
Denon
Dual
Dumont
Elbe
Ferguson
Finlandia
Finlux
Firstline
Fisher
GEC
Goodmans
Graetz
Granada
Grundig
Hinari
Hitachi
ITT
0081
0348, 0352
0041, 0106, 0315
0315, 0352
0041, 0104
0499
0162, 0195, 0226
0320, 0321, 0493
0041
0352
0352
0081
0637, 0642
0042, 0166
0081
0042
0041
0081, 0104
0038
0041, 0320, 0321, 0493
0081, 0104
0042, 0081, 0104
0043, 0045
0046, 0104
0081
0637
0041, 0104
0046, 0081, 0104
0081, 0195, 0226, 0347
0004, 0352
0004, 0041, 0042, 0166
0041, 0046, 0104, 0106,
0384
0004
0081
0041, 0067, 0384
0106
0041
0004, 0081, 0162, 1562
0004
0043, 0046, 0048, 0106,
0104,
0038
0045
0081
0004, 0348, 0352
0348
0046, 0104
0162, 0195, 0347, 1562
0195
0043, 0067, 0081
0081
0038, 0041, 0067
0081
0041, 0046, 0104, 0106
Nordmende
0041, 0320, 0321, 0384,
0494
0041
0348, 0315
0004, 0348, 0352
0081
0041
0162, 0226, 0836, 1562,
1662
0041
0042
0038
0081, 0384
0081
0067, 0081
0081
0046
0081
0081
0041, 0384
0081
0004, 0081
0041, 0320, 0321, 0384,
0494
0004
0043, 0046, 0106
0432
0041, 0067
0046, 0104
0352
0041, 0104
0081
0041
0048
0104
0004
0081, 0104, 0195
0045
0004, 0081
0046
0032, 0033, 1032
0348
0041, 0081
0162, 0226
0041, 0493
0041, 0320, 0321, 0384,
0493, 0494
0041, 0067, 0320, 0321,
0384, 0493, 0494, 0528
0041, 0104
0041, 0043, 0045, 0081,
0384
0081, 0106, 0195
0615
Teac
Tec
Technics
Technol Ace
Telefunken
Teletech
Teleton
Tensai
Tenosal
Texet
Thomson
Thorn
Tomashi
Toshiba
Triumph
Uher
Ultra
Ultravox
Universum
Vestel
Videosat
Videotechnic
Videomagic
Villain
Voxson
Waltham
Watson
Watt Radio
Wega
White
Westinghouse
Yamishi
Yapshe
Yoko
Yokan
Zanussi
0803
0250
0037, 0217, 0264, 0804
0803
0206
Ingersol
Interfunk
JVC
Kendo
Kenwood
Loewe
Logik
Luxor
M Electronic
Manesth
Marantz
Matsui
Medion
Memorex
Metz
Minerva
Mitsubishi
Myryad
NEC
Neckermann
Nokia
Oceanic
Okano
Orion
Otto Versand
Palladium
Panasonic
Pathe Marconi
Pentax
Philco
Philips
Phonola
Pioneer
Pye
Quartz
Quelle
Radiola
Rex
SBR
SEI
Saba
Saisho
Salora
Samsung
Sansui
Sanyo
Saville
Schaub Lorenz
Schneider
Seleco
Sharp
Shintom
Shorai
Siemens
Singer
Sunudyne
Sonolor
Sony
Sunkai
Tatung
Technics
Teleavia
Telefunken
Thomson
Thorn
Toshiba
Universum
Wharfedale
43 EN
*5455/38-52/EN
43
04.6.16, 4:28 PM
Basic remote control operations for other components
Setup code chart
Satellite setup codes
Maker
Setup codes
Maker
Setup codes
Maker
Setup codes
ABsat
AST
Akai
Alba
Aldes
Amstrad
0123, 0832
0321, 0351
0515
0421, 0455, 0515, 0613
0288
0252, 0345, 0501, 0675,
0689, 0847, 1113
0288, 0369, 0519, 0713
0421
0834, 1043, 1205
0243
0142, 1129
0108
0173, 0358, 0501, 0520,
0548
0364
0396
0369, 0530, 0834
0515, 0668, 0710
0369
0173
0243, 0829
0847, 1175
Gooding
Grundig
0571
0139, 0140, 0173, 0571,
0750, 0805, 0847, 1150
1011, 1159
0173, 0396, 0397, 0398,
0495, 0501, 0573, 0882,
1085
0455
0668
0283, 0863, 1176
0243, 0288, 0794
0609, 0816
1011, 1159
0108
0871
0592
0710
0364
0515, 0571
0123, 0173, 0200, 0249,
0331, 0358, 0442, 0480,
0553, 0622, 0658, 1057,
1224
0794
0331
0173
0421
1043
0520, 0607
0421
0592
1122
1017
0369
0108, 0573
0455, 0520, 0592, 0765,
1017, 1083
0200
0495, 0750
0571
0853
0243
0084, 0713, 1215
1003
0571
0132, 0243, 0683, 0829,
1103
0642, 0879
0331
0200
0501
0692, 0834
0732
0713
0108, 0397, 0455, 0573,
0723, 0751, 0873, 1023,
1127
1022
0501
0241, 0455, 0497,0720,
0791, 0795, 0847, 0867,
0887, 1175
0571
0501
0879, 0615
Panasonic
Panda
Patriot
Philips
0847, 1104
0455
0515
0133, 0200, 0292, 0455,
0571, 0710, 0750, 0805,
0853, 0898, 1118
0288, 0592
0329, 0352, 0853
1123
0132
0455
0288
0519, 0628
0200, 0288
0200
0396, 0882, 1113
0321, 0351
0369, 0421, 0742, 1087
0856
0157, 0240, 0713, 1200
0417
0520, 0690, 0710, 0885
0455
0820, 1114, 1253
0108
1017, 1243
0421, 0520, 0692
0605
1009
1083
0805
0552, 1111
0396, 0530
0173, 0683
1014
0240, 0288, 0519, 0605,
0628, 0713, 0880
0132
0278, 0847
1122
0132, 0879, 1088, 1105,
1159
0794
0887
0820
0455
0501, 0548, 1099, 1100,
1195
0421
0243, 0613
0605
0114, 0157, 0501
0455, 0853, 1012, 1046
0668
1206
0321, 0351
0414, 0501
0115
0136
0173, 0571
0351, 0690
0200
1042
Ankaro
Anttron
Arcon
Armstrong
Aston
Astra
Astro
AudioTon
Avalon
Axis
BT
Best
Blaupunkt
Boca
British Sky
Broadcasting
CNT
Cambridge
Canal Digital
Canal Satellite
Canal+
CityCom
Commlink
Connexions
Conrad
Crown
Cyrus
D-box
DMT
DNT
Digenius
Distratel
Dynasat
EIF
Echostar
Elta
Emanon
Engel
Eurostar
FTE
Ferguson
Fidelity
Finlux
Force NO AS
Fracarro
Freecom
Fuba
Galaxis
Galaxisat
Gardiner
Gold Box
0520
0515
0853
0853
0853
0115, 0818, 1176
0288
0396
0115, 0607
0243
0200
0723
1075
0200, 0396
0299
0084, 0885
0679
0417
0167, 0312, 0396, 0453,
0454, 0511, 0610, 0713,
0853, 0871, 1086, 1169
0364
0421
1017
0679, 1025, 1026
0331, 0863
0711
0252, 0675
0397, 0414, 0455, 0108
1101
0871
0421
0369, 0396, 0414, 0417,
0421
0283, 0288, 0364, 0833,
0834, 0863, 1101, 1111
0321
0818
0853
HDT
Hirschmann
Hitachi
Houston
Humax
Huth
IRTE
Hyundai
ITT
InVideo
Intervision
JOK
JSR
JVC
Kathrein
KeyWest
Kosmos
Kreiselmeyer
Kyostar
L&S Electronic
La Sat
Lenco
Lennox
Lifesat
Logix
Lupus
Luxor
Manhattan
Marantz
Maspro
Matsui
MediaSat
Mediamarkt
Metronic
Micronic
Minerva
Morgan’s
Multichoice
Multistar
Myryad
Neuhaus
Neusat
NextWave
Nikko
Nokia
Orbit
Orbitech
Pace
Palladium
Palsat
Panasat
Phonotrend
Pioneer
Praxis
Preisner
Promax
Prosat
Quadral
RFT
Radiola
Radix
SAT
SEG
SKY
SM Electronic
STVI
Saba
Sabre
Sagem
Salora
Samsung
SatPartner
Satcom
Satplus
Satstation
Schneider
Schwaiger
Seemann
Siemens
Sky Television
Skymaster
Smart
Sony
Starland
Strong
Sunstar
Supernova
TPS
Tantec
TechniSat
Telefunken
Teleka
Telesat
Telestar
Thomson
Tonna
Topfield
Triad
Triasat
Triax
Twinner
Universum
VTech
Ventana
Visiosat
44 EN
*5455/38-52/EN
44
04.6.16, 4:28 PM
Basic remote control operations for other components
Setup code chart
Satellite setup codes (continue)
DVD player setup codes
Maker
Setup codes
Maker
Setup codes
Maker
Setup codes
Vortec
Wisi
0421
0173, 0321, 0351, 0372,
0396, 0406, 0455, 0638,
0690
0123
0114, 0321, 0331, 0520,
0552, 0818, 1075
0856
0794
Afreey
Aiwa
Akai
Alba
Amoisonic
Amstrad
Apex Digital
Bush
Cat
Clatronic
Cyber Home
Cytron
Daewoo
Dansai
Decca
Denon
Denver
DiViDo
Enterprise
GoldStar
Goodmans
GPX
Greenhill
Grundig
H&B
Harman/Kardon
Himage
HiMAX
Hitachi
Hiteker
JVC
Jeutech
Kenwood
Konka
LG
Lasonic
Lecson
Lenco
Lenoxx
Limit
Logic
Mediencom
MiCo
Minato
Minowa
NAD
Nintaus
Onkyo
Optim
Oritron
Panasonic
Philco
Philips
Pioneer
REC
Redstar
Revoy
Roadstar
Rotel
SM Electronic
Slim Art
Samsung
Sanyo
Scheinder
0698
0641
0611
0717
0764
0713
0672, 0795
0516, 0690, 0811
0786, 0787, 0789
0788
0714, 0816
0716
0770, 0784, 0832, 0833
0770
0770
0490, 0634
0778
0705
0591
0741
0790
0769
0717
0539, 0701, 0705, 0775
0818
0702
0518
0843
0664
0672
0558, 0623
0777
0490, 0534, 0737
0711
0741
0743
0696
0774
0819
0768
0783
0746, 0773
0723, 0751
0752
0712
0692
0793
0612, 0627, 1612
0747
0651
0490
0690
0539, 0646
0525, 0571
0689
0748, 0763, 0805
0699
0689
0623
0690, 0730
0784
0573, 0744
0670
0783
Scott
Sherwood
Skyworth
Sony
Tatung
Teac
Technics
TerraTec
Thomson
Toshiba
Tredex
Umax
Wesder
Wharfedale
Xoro
Xwave
Yamakawa
Yelo
Zeus
0718
0633
0766
0533, 1533
0770, 0771
0759
0490
0825
0551, 0522
0503
0799, 0800, 0803
0690
0699
0686, 0696
0806, 0829
0709
0665, 0710, 0765
0780
0784
XSat
Zehnder
Zenith
Zwergnase
Cable setup codes
Maker
Setup codes
Alcatel
Birmingham cable
Communications
British Telecom
Cable & Wireless
Cabletime
Cryptovision
Decsat
Director
Filmnet
France Telecom
Golden Channel
Grundig
HyperVision
Jerrold
MNet
Mr. Zap
Noos
Ono
PVP Stereo
Visual Matrix
Pace
Philips
Pioneer
Sagem
Scientific Atlanta
Supercable
Tele+1
Thomson
Torx
Tudi
United Cable
Videoway
Visionetics
Westminster
Zenith
0896, 0897
0276
0003, 0105
1068
0448, 0665, 0377, 0271
0600
0423
0476
0443
0896, 0897, 0451
1110
0529
0619
0276, 0003
0443, 0019
1112
0817
1068
0003
1068, 1060
0619
0144
0817
0277, 0008, 0477
0276
0443
1110
0003
0286
0003
0250
1064
0105, 0716
0000
DTV decoder setup codes
Maker
Setup codes
Grundig
Panasonic
Pioneer
Princeton
Samsung
Sensory Science
Sharp
0467
1120
1010
0113, 0295
1190
1126
1010
45 EN
*5455/38-52/EN
45
04.6.16, 4:28 PM
Basic remote control operations for other components
Cassette deck, CD player & MD recorder operations
Refer to the following for the type of remote control operations available for each component.
1 Select the input source.
2 Press the keys corresponding to the operations you desire.
Refer to the following sections for details.
• When pressing keys in succession, press each key firmly and be sure
to wait at least 1 second before pressing the next key.
• Numeric keys function the same as the numeric keys on the original
remote.
These keys can be used to perform the basic operations of KENWOOD and other manufacturers’ components which the setup code for each
component had been entered beforehand.
°
Cassette deck operations keys
VID1
CD player operation keys
VID3
VID2
VID1
TUNER
DVD
6CH
CD
DVD
VID2
VID3
AV AUX
MD
TAPE
CD
DVD
DVD
6CH
TUNER
MD
TAPE
AV AUX
PHONO
T
Numeric keys
(Select tracks)
7
P. Call
S
P. Call
Enter
2
Disc Sel.
(Disc selection)
+ 100
TV Mute
A/B
(Cassette Deck
selection)
Page
Return
Last/ A/B
Mute
¢ (Skip up)
4 (Skip down)
+
Tone
CH
VOL
Sound
–
4
1 (Rewind)
¡ (Fast Forward)
8 (Pause)
–
+
TV
VOL
–
Band
Dimmer
Auto
¶ (Record)
3/8 (Play/Pause)
Top Menu
Setup
Loudness
Listen
Mode
DSP
Mode
Stereo
Remote
Setup
THX
Input
Mode
Speaker
EQ
Active
EQ
+
¢
CH
2 (Reverse play)
VID1
TUNER
DVD
6CH
CD
DVD
VID2
VID3
AV AUX
MD
TAPE
PHONO
Auto
Top Menu
7 (Stop)
Info / Flip
S
T
6
P. Call
Enter
7
Multi
1
8
0
+ 10
9
+ 100
TV Mute
+100
(Select tracks)
Page
Return
OSD
Last/ A/B
Exit
Guide
Disc Skip
Menu
Disc Sel.
¢ (Skip up)
4 (Skip down)
Mute
Input Sel.
+
¢
CH
TV
VOL
+
VOL
Sound
–
4
–
8 (Pause)
Tone
+
TV Input
–
Bass
Boost
Tune –
Band
Tune +
Dimmer
Auto
Top Menu
3/8 (3 Play)
Info / Flip
Setup
Loudness
Listen
Mode
Active
EQ
DSP
Mode
Stereo
Remote
Setup
THX
Input
Mode
Speaker
EQ
1 (Search)
¡ (Search)
¶ (Record)
7 (Stop)
46 EN
*5455/38-52/EN
46
04.6.16, 4:28 PM
1 (Search)
¡ (Search)
Setup
Loudness
Listen
Mode
5
Multi
2
Bass
Boost
Dimmer
Active
EQ
Disc Skip
–
Tune +
V Pow
P. Call
Numeric keys
(Select tracks)
TV Input
Band
er
r
we
4
3
Sound
+
Tune –
TV
POWER
RCVR
Po
RC
TV
VOL
+
VOL
–
4
MD recorder operation keys
SRC Power
(Source power)
Tone
Tune +
Info / Flip
7 (Stop)
Mute
Input Sel.
–
Bass
Boost
TV Input
Tune –
Menu
Disc Sel.
Disc Sel.
+
Guide
Disc Skip
Input Sel.
¢
OSD
Last / A/B
Exit
Menu
+ 100
Page
Return
Guide
Disc Skip
9
TV Mute
OSD
Exit
8
0
+ 10
9
7
1
8
0
6
Enter
Multi
Multi
1
+ 10
5
Multi
P. Call
P. Call
2
4
3
6
Multi
V Pow
er
5
3
TV
POWER
RCVR
Po
RC
r
we
4
SRC Power
(Source power)
V Pow
er
r
we
Po
RC
T
TV
POWER
RCVR
S
PHONO
DSP
Mode
Stereo
Remote
Setup
THX
Input
Mode
Speaker
EQ
3/8(Play/pause)
Basic remote control operations for other components
Other components’ operations
Refer to the following for the type of remote control operations available for each component.
TV operation keys
VCR operation keys
VID1
TUNER
DVD
6CH
CD
DVD
VID1
TUNER
DVD
6CH
CD
DVD
VID2
VID3
AV AUX
MD
TAPE
VID2
VID3
AV AUX
MD
TAPE
1
Exit
8
0
+ 10
9
+ 100
TV Mute
TV Mute
Page
Last
(Last channel)
CH + / –
(Channel + / –)
TV VOL
Return
OSD
Last / A/B
Exit
Guide
Menu
Guide
Disc Skip
Menu
Disc Sel.
Mute
Input Sel.
+
¢
+
Tone
CH
–
+
TV
VOL
–
Band
Tune +
Auto
Top Menu
Info / Flip
Setup
Dimmer
THX
Input
Mode
Active
EQ
T
Enter
Info(Display)
Remote
Setup
Exit
%(Cursor up)
fi(Cursor down)
@Cursor left)
#(Cursor right)
8
0
+ 10
9
+ 100
Guide
TV Mute
Input Sel.
(Input selection)
Page
Return
OSD
Last / A/B
Exit
Menu
Mute
+
¢
Tone
CH
–
8 (Pause)
+
Last
(Last channel)
VOL
Sound
–
4
Menu
Guide
Disc Skip
Disc Sel.
Input Sel.
Info (Display)
Speaker
EQ
7
Multi
+
TV
VOL
TV Input
Tune –
Dimmer
–
Bass
Boost
Band
Tune +
Auto
Top Menu
Info / Flip
Loudness
Stereo
2
1
1 (Rewind)
¡ (Fast Forward)
Listen
Mode
DSP
Mode
6
Multi
Enter
TV Input
Bass
Boost
TV Input
Tune –
Numeric keys
CH + / –
(Channel + / –)
VOL
Sound
–
4
5
3
P. Call
T
S
P. Call
Multi
4
V Pow
P. Call
7
TV
POWER
RCVR
Po
RC
er
Enter
Enter
%(Cursor up)
fi(Cursor down)
@Cursor left)
#(Cursor right)
6
P. Call
2
TV Power
5
Multi
SRC Power
(Source power)
r
we
V Pow
er
r
we
4
3
Numeric keys
PHONO
TV
POWER
RCVR
Po
RC
S
PHONO
Setup
Loudness
Listen
Mode
DSP
Mode
Stereo
Remote
Setup
THX
Input
Mode
Speaker
EQ
Active
EQ
¶ (Record)
3/8 (3 Play)
7 (Stop)
REMOTE CONTROL UNIT RC-R0820
REMOTE CONTROL UNIT RC-R0820
DVD player operation keys
VID1
TUNER
DVD
6CH
CD
DVD
VID2
VID3
AV AUX
MD
TAPE
PHONO
T
S
4
5
3
8 (Pause)
7 (Stop)
Flip
P. Call
P. Call
Enter
7
Multi
1
8
0
+ 10
9
+ 100
TV Mute
Page
Return
OSD
Last/ A/B
Exit
Guide
Disc Skip
¢ Skip up
4 Skip down
6
Multi
2
Return
Disc Sel.
(Disc selection)
V Pow
er
Enter
Page ∞/5
(Page down or up)
TV
POWER
RCVR
Po
RC
r
we
SRC Power
(Source power)
Numeric keys
(Select tracks)
Menu
Disc Sel.
Mute
Input Sel.
+
¢
+
Tone
CH
VOL
Sound
–
4
–
TV
VOL
+
–
Bass
Boost
TV Input
Tune –
Band
Tune +
Dimmer
Auto
Top Menu
Setup
Info / Flip
%(Cursor up)
fi(Cursor down)
@Cursor left)
#(Cursor right)
+100
OSD (On Screen Display)
Menu
Disc Skip
1 (Search)
¡ (Search)
Top Menu
(Title)
Loudness
Listen
Mode
Active
EQ
DSP
Mode
Stereo
Remote
Setup
THX
Input
Mode
Speaker
EQ
3/8 (3 Play)
REMOTE CONTROL UNIT RC-R0820
47 EN
*5455/38-52/EN
47
04.6.16, 4:28 PM
Basic remote control operations for other components
Satellite operation keys
Cable operation keys
VID1
TUNER
DVD
6CH
CD
DVD
VID1
TUNER
DVD
6CH
CD
DVD
VID2
VID3
AV AUX
MD
TAPE
VID2
VID3
AV AUX
MD
TAPE
1
Exit
Last
(Last channel)
Input Sel.
(Input selection)
8
0
+ 10
9
Page
Return
OSD
Last / A/B
Exit
Guide
Disc Skip
+
Tone
–
TV
VOL
Sound
+
TV Input
Tune –
Dimmer
T
1
Auto
Top Menu
9
Listen
Mode
DSP
Mode
Stereo
Remote
Setup
THX
Input
Mode
Speaker
EQ
REMOTE CONTROL UNIT RC-R0820
+ 100
Page
Return
OSD
Last/ A/B
Exit
Tone
CH
TV
VOL
Sound
+
TV Input
Tune –
Dimmer
–
Bass
Boost
Band
Tune +
Auto
Top Menu
Info / Flip
Setup
Loudness
Listen
Mode
Active
EQ
Last(Last channel)
+
VOL
–
–
Menu
Guide
Menu
Mute
+
¢
4
Info
(Information)
Guide
TV Mute
Setup
Loudness
%(Cursor up)
fi(Cursor down)
@Cursor left)
#(Cursor right)
8
0
+ 10
Input Sel.
Input Sel.
(Input selection)
CH + / –
(Channel + / –)
Bass
Boost
Tune +
Info / Flip
Active
EQ
Menu
–
Band
7
Disc Sel.
VOL
–
4
Enter
Disc Skip
+
6
Multi
Exit
Mute
Input Sel.
¢
Page ∞¥5
Guide
2
Enter
Page ∞/5
(Page down or up)
5
Multi
Menu
Disc Sel.
CH
CH + / –
(Channel + / –)
+ 100
TV Mute
S
T
S
P. Call
7
Multi
4
3
Numeric Keys
V Pow
P. Call
P. Call
Enter
%(Cursor up)
fi(Cursor down)
@Cursor left)
#(Cursor right)
TV
POWER
RCVR
Po
RC
er
6
SRC Power
(Source power)
r
we
5
Multi
2
PHONO
V Pow
er
r
we
4
3
Enter
Numeric keys
TV
POWER
RCVR
Po
RC
P. Call
PHONO
SRC Power
(Source power)
DSP
Mode
Stereo
Remote
Setup
THX
Input
Mode
Speaker
EQ
Info
(Information)
REMOTE CONTROL UNIT RC-R0820
Notes
1. Certain codes may only operate some of the function available on a given model.
2. The above show the typical type functions available for each component. Some manufacturers use different key combinations to perform similar
functions. For that reason, we have programmed extra functions on some of the unused number keys to help you control your equipment.
48 EN
*5455/38-52/EN
48
04.6.16, 4:28 PM
In case of difficulty
Resetting the Microcomputer
With the power cord plugged in, turn the POWER ON/OFF
key OFF. Then, while holding down the ON/STANDBY
key, press POWER ON/OFF.
The microcomputer may malfunction (unit cannot be operated, or
shows an erroneous display) if the power cord is unplugged while
the power is ON, or due to some other external factor. If this
happens, execute the following procedure to reset the
microcomputer and return the unit to its normal operating
condition.
• Please note that resetting the microcomputer will clear the contents
of the memory and returns the unit to the state it was in when it left
the factory.
Amplifier
Symptom
Remedy
Cause
No sound from the speakers.
• Connect them properly referring to
“Connecting the speakers”
%
• Adjust the volume to a proper level.
• Turn OFF the MUTE.
¢
• Set the SPEAKERS switches to ON. £
• The speaker cords are disconnected.
• VOLUME is set to the minimum position.
• MUTE is ON.
• The SPEAKERS switches are set to OFF.
The standby indicator blinks and sound is
not output.
• Speaker cords are short-circuited.
• Turn the power off, eliminate the shortcircuiting, then turn on the power again.
Sound is not output from one of the speakers.
• The speaker cord is disconnected.
• Connect it properly referring to “Connecting
the speakers”.
%
• Set it up properly referring to “Speaker settings”.
(
• The speaker is not set up correctly.
Sound is not output from the surround
speakers and / or the center speaker, or their
sound is very small.
• The surround speaker cords and/or the center
speaker cord is disconnected.
• The speaker is not set up correctly.
• A surround mode has not been engaged.
• The surround and/or center volume controls
are set to the minimum level.
• Connect it properly referring to “Connecting
the speakers”.
%
• Set it up properly referring to “Speaker settings”.
(
• Select a surround mode.
• Adjust the speaker levels using the test tone.
)
A humming noise is generated when the
PHONO input selector is selected.
• The audio cord from the record player is not
connected to the PHONO jacks.
• The record player is not grounded.
• Insert the audio cord plugs securely into the
PHONO jacks.
• Connect the grounding wire to the GND
terminal on the rear panel.
When playing a Dolby Digital source signal
using a DVD player, the sound is cut off soon
after it starts.
• There are many possible causes for this
problem, depending on the type of DVD player
used.
• Set the input mode to digital manual before
starting playback of the Dolby Digital source.
8
No sound is produced during playback from
a DVD player.
• The input mode is set to digital manual.
• Press the INPUT MODE key to select to full
auto mode.
8
A video source cannot be recorded
normally.
• The software is copy-guarded.
• Copy-guarded video software cannot be
recorded.
Tuner
Cause
Remedy
Radio stations cannot be received.
• No antenna is connected.
• The broadcast band is not set properly.
• The frequency of the desired station is not
tuned.
• Connect an antenna.
*
• Set the broadcast band properly.
• Tune the frequency of the desired station.
¶
Interference.
• Noise due to ignition noise from an automobile.
• Install the outdoor antenna away from the
road.
• Turn off the power to the appliance.
Symptom
• Noise due to interference from an electric
appliance.
• Noise due to a nearby TV set.
A station which was preset cannot be
received by pressing the corresponding
numeric key.
• The preset station belongs to a frequency that
cannot be received.
• The preset memory was cleared because the
power cord had been unplugged for a long
period of time.
• Install the receiver farther away from the TV.
• Preset a station with a receivable frequency.
• Preset the station again.
49 EN
*5455/38-52/EN
49
04.6.16, 4:28 PM
In case of difficulty
Remote control unit
Symptom
Cause
Remedy
Certain inputs cannot be selected using the
remote control.
• No setup codes registered for the respective
input(s).
• Register a setup code at the respective input(s).
°
Remote control operation is not possible.
• The remote control is set to a different operation
mode.
• Batteries are exhausted.
• The remote control unit is too far away from
the main system, controlling angle is too large,
or there is an obstacle between the receiver
and the remote.
• No tape or CD is placed in the source
component.
• An attempt is made to play a tape which is
being recorded in the cassette deck.
• The remote control has not been set to the
operation mode for the component you wish
to control.
• Press any of the Input Selector keys to select
the appropriate operation mode.
• Replace with new batteries.
• Operate the remote control unit within the
controllable range.
• Place the tape or CD in the source component
which you want to play.
• Wait until recording has completed.
• Press any of the source keys or SRC Power
key to activate the operation mode for the
component you want to control before
operation.
·
50 EN
*5455/38-52/EN
50
04.6.16, 4:28 PM
Caution : Read this page carefully to ensure safe
operation.
Specifications
AUDIO section
DIGITAL AUDIO section
Rated power output during STEREO operation
DIN/IEC (20 Hz ~ 20kHz, 0.09 % T.H.D. at 8 Ω ) ...............................
............................................................................... 100 W + 100 W
(1 kHz, 10 % T.H.D. at 8 Ω ) ...................................... 130 W + 130 W
Effective power output during SURROUND operation
FRONT
(20 Hz ~ 20 kHz, 0.09 % T.H.D. at 8 Ω one channel driven)
............................................................................... 100 W + 100 W
(1 kHz, 10 % T.H.D. at 8 Ω one channel driven)
............................................................................... 130 W + 130 W
CENTER
(20 Hz ~ 20 kHz, 0.09 % T.H.D. at 8 Ω one channel driven)
.............................................................................................. 100 W
(1 kHz, 10 % T.H.D. at 8 Ω one channel driven) ................ 130 W
SURROUND
(20 Hz ~ 20 kHz, 0.7 % T.H.D. at 8 Ω one channel driven) ...........
............................................................................... 100 W + 100 W
(1 kHz, 10 % T.H.D. at 8 Ω one channel driven)
............................................................................... 130 W + 130 W
SURROUND BACK
(20 Hz ~ 20 kHz, 0.7 % T.H.D. at 8 Ω one channel driven) .........
................................................................................ 100W + 100 W
(1 kHz, 10 % T.H.D. at 8 Ω one channel driven)
............................................................................... 130 W + 130 W
Sampling frequency ...................... 32 kHz, 44.1 kHz, 48 kHz, 96 kHz
Input level / impedance / wave length
Optical .............................. –15 dBm ~ –24 dBm, 660 nm ±30 nm
Coaxial .......................................................................... 0.5 Vp-p / 75 Ω
Output level / impedance / wave length
Optical .............................. –21 dBm ~ –15 dBm, 660 nm ±30 nm
Total harmonic distortion ....................... 0.009 % (1 kHz, 50 W, 8 Ω )
Frequency response
(CD/DVD, TAPE, VIDEO 1, VIDEO 2, VIDEO 3, DVD/6CH)
................................................... 10 Hz ~ 100 kHz, 0 dB ~ –3.0 dB
PHONO ‘RIAA’ response .............. 40 Hz ~ 20 kHz, +1.5 dB ~ –3.0 dB
Maximum input level
PHONO (MM) .................................... 40 mV, 1 % T.H.D. at 1 kHz
Signal to noise ratio (IHF’66)
PHONO (MM) ........................................................................ 75 dB
Line (CD/DVD, TAPE, VIDEO 1, VIDEO 2, VIDEO 3, DVD/6CH)
............................................................................................... 95 dB
Loudness control
VOLUME at –30 dB level ...................................... +6 dB (100 Hz)
Input sensitivity / impedance
Ω
PHONO (MM) ........................................................... 4 mV / 47 kΩ
(CD/DVD, TAPE, VIDEO 1, VIDEO 2, VIDEO 3, DVD/6CH)
Ω
.............................................................................. 300 mV / 47 kΩ
Output level / impedance
Ω
TAPE REC ............................................................... 300 mV / 1 kΩ
PRE OUT (FRONT CHANNEL) ................................... 1 V / 500 Ω
PRE OUT (CENTER CHANNEL) ................................. 1 V / 500 Ω
PRE OUT (SURROUND CHANNEL) .......................... 1 V / 500 Ω
PRE OUT (SURROUND BACK CHANNEL) ............... 1 V / 500 Ω
PRE OUT (SUBWOOFER) .......................................... 1 V / 500 Ω
Tone control
BASS ................................................................ ±10 dB (at 100 Hz)
TREBLE ............................................................ ±10 dB (at 10 kHz)
VIDEO section
VIDEO inputs / outputs
VIDEO (composite) ................................................. 1 Vp-p / 75 Ω
S VIDEO inputs /outputs
S VIDEO (luminance signal) ................................... 1 Vp-p / 75 Ω
S VIDEO (chrominance signal) ....................... 0.286 Vp-p / 75 Ω
COMPONENT VIDEO inputs/ outputs
COMPONENT VIDEO (luminance signal) ............. 1 Vp-p / 75 Ω
COMPONENT VIDEO (CB/CR-signal) ................. 0.7 Vp-p / 75 Ω
FM tuner section
Tuning frequency range ................................. 87.5 MHz ~ 108.0 MHz
Usable sensitivity
MONO ............. 1.6 µV (75 Ω)/ 15.2 dBf (75 kHz dev, SINAD 30 dB)
50dB quieting sensitivity
STEREO ..................................... 28 µV (75 Ω)/ 40.2 dBf (75 kHz dev)
Total harmonic distortion
MONO (1 kHz, 75 kHz dev) .......................... 0.5% (65 dBf input)
STEREO (1 kHz, 67.5 + 67.5 kHz dev) ......... 0.7% (65 dBf input)
Signal to noise ratio
MONO (1 kHz, 75 kHz dev) ........................ 75 dB (65 dBf input)
STEREO (1 kHz, 67.5 + 67.5 kHz dev) ....... 68 dB (65 dBf input)
Stereo separation (1 kHz) ........................................................... 40 dB
Selectivity ( ±400 kHz) ................................................................ 50 dB
Frequency response (30 Hz ~ 15 kHz) .................... +0.5 dB, –3.0 dB
AM tuner section
Tuning frequency range (9 kHz step) ............... 531 kHz ~ 1,602 kHz
(10 kHz step) ............. 530 kHz ~ 1,610 kHz
Usable sensitivity (30% mod, S/N 20 dB) ......... 16 µV / (600 µV/m)
Signal to noise ratio (30% mod, 400 Hz) ............................................
.................................................................. 50 dB (60 dBµV EMF input)
GENERAL
Power consumption .................................................................. 300 W
Standby Power consumption .................................... less than 1.5W
AC outlet
SWITCHED ........................................................ (total 90 W max.)
Dimensions ..................................................... W : 440 mm (17-5/16")
H : 159 mm (6-1/4")
D : 392 mm (15-7/16")
Weight (Net) ............................................................ 12.1 kg (26.7 lb)
Notes
1. KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without notice.
2. The full performance may not be exhibited in an extremely cold location (under a water-freezing temperature).
51 EN
*5455/38-52/EN
51
04.6.16, 4:28 PM
For your records
Record the serial number, found on the back of the unit, in the spaces
designated on the warranty card, and in the space provided below. Refer
to the model and serial numbers whenever you call upon your dealer for
information or service on this product.
Model __________________ Serial Number ________________________
52 EN
*5455/38-52/EN
52
04.6.16, 4:28 PM