Hilti X-PT 2 Operating Instruction

X-PT 2
Printed: 10.06.2015 | Doc-Nr: PUB / 5199244 / 000 / 02
Operating instructions
en
Mode d’emploi
fr
Manual de instrucciones
es
Manual de instruções
pt
1
ꙣ
Ꙥ
ꙥ
Ꙧ
ꙧ
Printed: 10.06.2015 | Doc-Nr: PUB / 5199244 / 000 / 02
2
3
4
5
6
7
8
Printed: 10.06.2015 | Doc-Nr: PUB / 5199244 / 000 / 02
9
10
ƒ
11
12
Printed: 10.06.2015 | Doc-Nr: PUB / 5199244 / 000 / 02
Programme
Technical description
No.
Description
Length
Weight
Ordering designation
Item no.
쩸
쩹
쩺
쩻
쩼
Pole tool
Tool holder
Extension
Extension
Grip section assy
31/2 ft (1.14 m)*
111/16 ft (0.51 m)
3 ft (0.93 m)
1 ft (0.31 m)
19/16 ft (0.48 m)
2.0 kg
0.6 kg
0.7 kg
0.3 kg
0.7 kg
X-PT 2
2105327
2094657
254684/4
254685/1
254687/7
DXA 3 ft
DXA 1 ft
*Overall length incl. DX 2
Selection chart
Pos.
Part
Number of sections
5 ft (1.45 m )
7 ft (2.07 m)
10 ft (3.00 m)
13 ft (3.93 m)
쩹
쩺
쩻
쩼
Tool holder
Extension
Extension
Grip section assy
1
–
1
1
1
1
–
1
1
2
–
1
1
3
–
1
Intermediate lengths, e.g. 8 ft (2.39 m) can be achieved by fitting a 1 ft (0.31 m) extension to the 7 ft (2.07 m) version
Malfunctioning and troubleshooting
Malfunction
Solution to problem (after lowering the pole tool – see cover)
Tool does not fire.
Check that the tubular extension pieces are screwed in as far as they will
go.
Advance the cartridge strip manually (pull) to the next position.
Cartridge has not been transported.
Manufacturer’s warranty - tools
Please contact your local Hilti representative if you have questions about the warranty conditions.
1
Printed: 10.06.2015 | Doc-Nr: PUB / 5199244 / 000 / 02
Assembling the pole tool
 Screw together the tubular sections and the tool holder. Tighten the
parts by hand only – do not use
tools, wrenches etc.
 Screw on the grip section. The
maximum permitted overall length
including the tool is 13 ft. (3.96 m).
A maximum of 3 extension tubes
may be used.
 Open the clamping bar by unscrewing the knurled screw.
 Insert the DX 2.
 Secure the tool with the clamping
bar by tightening the knurled screw.
 The firing lever must be positioned in front of the trigger.
The pole tool should be not used if the grip section, DX tool holder or tubular extension sections are cracked or
otherwise damaged. Defective parts should be replaced.
Operation
 Please refer to the DX 2 operating
instructions for information on loading and using the DX tool.
 Fastening: Hold the pole tool at
right angles to the surface into which
the fastener is to be driven. Press the
muzzle of the tool against the work
surface and then operate the firing
lever located on the grip section.
 The grip section can be rotated in
order to achieve a comfortable operating position.
Caution: Do not hold the pole tool
at an angle to the ceiling. It must
always be held perpendicular to
the surface of the material into
which the fastener is to be driven.
Disassembly
 Lower the tool for reloading as
shown in the illustration.
Caution: Do not bump/hit/drop grip
on hard surfaces (eg. floor, ground).
 Caution: Do not swing the pole
tool down horizontally while holding the end of the extension
tubes.
2
Printed: 10.06.2015 | Doc-Nr: PUB / 5199244 / 000 / 02
The DX tool should be removed and
the pole tool disassembled in the
reverse order to assembling the tool.
Hilti Corporation
Printed: 10.06.2015 | Doc-Nr: PUB / 5199244 / 000 / 02
2105176
Hilti = registered trademark of Hilti Corp., Schaan
Pos. 1 | 20150528
*2105176*
LI-9494 Schaan
Tel.: +423 / 234 21 11
Fax:+423 / 234 29 65
www.hilti.com