advertisement
USER GUIDE
R10+ CAR DVR
Your expert witness on board
Languages
English 4
3
Community
/kaiserbaas
4
Tech support: e: [email protected] w: www.kaiserbaas.com/support p: Australia 1300 302 306 p: New Zealand 0800 302 306
(business hours, AEST)
Contents
5
6
Safety Precautions
Before using your R10+ Car DVR, please ensure you have read and understood all of the information below.
• Only use the provided USB-mini cable to power the
R10+.
• Do not expose the R10+ to water, dust, oil or temperatures above 70˚c.
• Avoid leaving the R10+ in direct sunlight for prolonged periods of time.
• Please do not attempt to adjust the camera or settings whilst you are operating your vehicle.
PLEASE OBEY ALL ROAD LAWS IN YOUR REGION WHILST
USING YOUR R10+. CHECK ALL LOCAL LEGISLATION
BEFORE USE.
What’s in the Box
Please ensure the product package has all the following contents:
A
B
C
R10 Car DVR
Windscreen Mount
3m USB Mini Cable
E
F
G
D
User Guide
Car Charger
80cm USB Mini Cable
Adhesive Pad
A
C
E
D
G
F
B
7
8
Product Diagram
1
Wide Angle Lens
2
Mounting Slot
3
2.7” Display
4
POWER Button
5
MENU Button
6
MODE Button
7
UP Button
8
OK Button
9
DOWN Button
10
Micro SD Slot
11
HDMI Mini Port (adapter required for HDMI)
12
AV Out Port
13
Mini USB Port
2
12
13
1
10
11
4
5
6
3
7
8
9
Setting up the R10+
General
• Insert a Micro SD card into the allocated slot on the left side of the R10+. An ideal placement for the R10+ is behind the rear vision mirror.
• The R10+ will power up and start recording as soon as it receives power from the connected USB-mini power cable (i.e turning your car on)
Car set up
• Clean your windscreen, making sure the placement of the R10+ does not obscure the view of the driver.
• Attach the R10+ to the mount by sliding the R10+ connection from left to right along the mount connection until latched into place.
• Remove the protective layer from the 3M adhesive on the mount.
• Stick the adhesive to the inside of the front windscreen in the desired position. Press for 30 seconds to ensure that the R10+ is mounted securely.
• Adjust the pivot connection to ensure that the R10+ is correctly angled.
• Finally connect the R10+ to power using the 3m USBmini power cable and the USB car charger, make any final adjustments to placement as necessary.
9
10
In Car Operation
The R10+ is optimised to use a Class 6 Micro SD card (not included) with at least 8GB of free space. For best results please use a Class 6 Micro SD card.
• The internal G-sensor will register any impacts and will log them as an ‘Event’. These ‘Event’ files will be stored in the RO file and will not be recorded over by regular footage. These files need to be manually deleted from your Micro SD card by connecting your R10+ to your computer or by formatting the Micro SD card.
• For more information on the R10+ interface please see page 12
Computer Connection
• Either connect the R10+ via the USB-mini cable, or insert the Micro SD card (not included) to your computer via an SD card adapter.
• Select “Mass Storage” mode to access files.
• R10+ will appear as an external storage device.
• Video files will be kept in a directory within the external storage under the directory titled VOLUME1/CARDV/
MOVIE (Event files will be moved to the RO file)
• Click on any of the video files for playback.
11
12
Interface
Recording/Viewfinder screen
From this screen you can manually start and stop recording using the OK button. You can also navigate to the menu screen by using the MENU button. Cycle through the
Recording and Video Playback modes using the MODE key.
To cycle through these modes you will need to ensure that the camera is not recording. In Photo mode the UP and
DOWN buttons are used to control the zoom function.
1
3
4
5
6
7
2
8
12
11
9
10
1
Mode (movie/photo)
2
G-sensor (On/Off)
3 Loop time (how long your camera will film before looping and creating a new file)
4
Exposure
5 Sound
6 Licence plate
7 Date
8 Time
9 Battery
10 Memory
11 Resolution
12 Recording time
Playback
In this screen the UP and DOWN buttons are used to navigate through files and the OK button is used to play back files. The MODE button is used to navigate back. Once a video is playing, the UP and DOWN buttons are used to control the volume and the OK button pauses. The MODE button stops the video.
1 2
3
5
4
6
1
Video icon
2 File name
3 Resolution
4 Date
5
Time
6 Battery
Menu
The R10+ menu can be accessed by pushing the MENU button. The MENU button can then be used to cycle through the different menus. The UP and DOWN buttons are used to navigate though the sub-menus and the OK and MENU buttons are used to select and navigate back respectively.
13
14
Film menu
Resolution:
Defines the level of recording detail.
Loop Recording
Sets the length of recording loop files.
WDR
Toggles wide dynamic range.
• 1296P (scaled up)
• 1080P
• 720P
• WVGA
• VGA
• Off
• 1 Minute
• 3 Minutes
• 5 Minutes
• Off
• On
Exposure
Sets exposure levels.
Motion Detection
Triggers recording when motion is detected.
Record Audio
Mutes or unmutes recording.
Date Stamp
Add or remove the date stamp from footage.
• -1/3
• -2/3
• -1.0
• -4/3
• -5/3
• -2.0
• Off
• On
• +2.0
• +5/3
• +4/3
• +1.0
• +2/3
• +1/3
• +0.0
• Off
• On
• Off
• On
15
16
Parking Guard
When activated, the R10+ will detect an impact or shock after the car has been parked, triggering a
30 second recording.
• Off
• On
G-Sensor
Determine the sensitivity of the trigger for the
Parking Guard and Event
Recording.
• Off
• Low
• Medium
• High
Camera Settings Menu
In the menu, push the MENU button a second time to navigate to the camera settings menu.
Date/Time
Set time and date to be displayed on footage.
Auto power off
Determine duration of inactivity before the camera powers down.
Beep sound
Toggle settings for sounds that indicate button use.
• Off
• 30 Seconds
• 1 Minute
• Off
• On
Language
Set language for device.
Frequency
Allows the frequency to be edited.
Carplate
Add or remove your licence plate from the footage.
• 50 Hz
• 60 Hz
• Off
• On (Enter licence plate number)
Format
A quick way to delete all items on the inserted
Micro SD card. (This will permanently delete all footage on the card)
Default setting
This resets all of the settings on your R10+.
Screen saver
The screen saver function puts the screen to sleep whilst recording. Select the length of time before the screen saver activates.
Version
This displays the camera version number.
• Off
• 1 Minute
• 5 Minutes
• 10 Minutes
17
18
Specifications
Dimension (L x W x H)
Weight
Lens
CMOS
LCD Display
Resolution
110mm x 47mm x 25mm
70g
140˚ Wide Angle Lens
AR0330
2.7” 16:9
1920 x 1080 FHD 30fps
Compresson format
Cigarette adaptor
Input voltage
H.264
DC 12/24 V
Main unit Input voltage DC 5 V
Power Current DC5V Recording current 450mA/
Standby 350mA
Power Consumption
Battery
Storage
2.3W
180mAh Lithium polymer
Class 6 Recommended
Max 32GB
Operation Temperature -20°C - 65°C
Storage Temperature -20°C - 75°C
Frequently Asked Questions
Q. The image is blurry.
A. Try repositioning the camera. For best results, try and aim the camera through a section of the windshield that is not overly curved or angled, as this can cause a blurring effect.
Q. My device will not record.
A. Please ensure that you have your R10+ connected to a power source using the supplied USB-mini power cable and that you have a Micro SD card inserted that is Class 4
(ideally Class 6) or above and 32GB or below.
Q. My HDMI cable will not fit in the HDMI socket on the camera.
A. The socket at the top of the R10+ is a mini HDMI port and requires a mini HDMI adapter (not included) for use with
HDMI cables.
Q. I can’t delete files off of my Micro SD card using the
R10+ settings.
A. It may be that the file that you are trying to delete has been flagged as an “Event” file by the R10+ G-sensor. These files can only be deleted by connecting your R10+ to a computer, or by formatting your Micro SD card.
19
20
Contact Us
Having trouble setting your R10+ Car DVR up?
Please contact us. No question too big or small and we are more than happy to help.
Please visit: www.kaiserbaas.com/support
Or email: [email protected]
For further information please visit: www.kaiserbaas.com
Tech support: e: [email protected] w: www.kaiserbaas.com/support p: Australia 1300 302 306 p: New Zealand 0800 302 306
(business hours, AEST)
advertisement
Related manuals
advertisement