Yamaha EC-03 Owner`s manual

✤✰✯✲✣❉❖
❉❊ ✤ Read this manual carefully before operating this vehicle.
OWNER’S MANUAL
EC-03
1CB-28199-E0
✤✰✯✲✣❉❖
❉❊ ✥ EAU46090
Q Read this manual carefully before operating this vehicle. This manual should stay with this vehicle if it is sold.
1CB-9-E0.book 1 ページ
2010年10月15日 金曜日 午前10時19分
INTRODUCTION
EAU10113
Welcome to the Yamaha world of motorcycling!
As the owner of the EC-03, you are benefiting from Yamaha’s vast experience and newest technology regarding the design
and manufacture of high-quality products, which have earned Yamaha a reputation for dependability.
Please take the time to read this manual thoroughly, so as to enjoy all advantages of your EC-03. The Owner’s Manual does
not only instruct you in how to operate, inspect and maintain your scooter, but also in how to safeguard yourself and others
from trouble and injury.
In addition, the many tips given in this manual will help keep your scooter in the best possible condition. If you have any further questions, do not hesitate to contact your Yamaha dealer.
The Yamaha team wishes you many safe and pleasant rides. So, remember to put safety first!
Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most current product information available at the time of printing, there may be minor discrepancies between your scooter and this
manual. If there is any question concerning this manual, please consult a Yamaha dealer.
EWA12411
WARNING
Please read this manual carefully and completely before operating this scooter.
1CB-9-E0.book 1 ページ
2010年10月15日 金曜日 午前10時19分
IMPORTANT MANUAL INFORMATION
EAU10132
Particularly important information is distinguished in this manual by the following notations:
This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety messages that follow this symbol to avoid possible injury
or death.
WARNING
A WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
NOTICE
A NOTICE indicates special precautions that must be taken to avoid damage to the
vehicle or other property.
TIP
A TIP provides key information to make procedures easier or clearer.
1CB-9-E0.book 2 ページ
2010年10月15日 金曜日 午前10時19分
IMPORTANT MANUAL INFORMATION
EAU10200
EC-03
OWNER’S MANUAL
©2010 by Yamaha Motor Co., Ltd.
1st edition, September 2010
All rights reserved.
Any reprinting or unauthorized use
without the written permission of
Yamaha Motor Co., Ltd.
is expressly prohibited.
Printed in Japan.
1CB-9-E0.book 1 ページ
2010年10月15日 金曜日 午前10時19分
TABLE OF CONTENTS
SAFETY INFORMATION .................. 1-1
Further safe-riding points ................ 1-4
Charging the battery safely ............. 1-5
DESCRIPTION ..................................
Left view ..........................................
Right view ........................................
Controls and instruments.................
2-1
2-1
2-2
2-3
EC-03 FEATURES .............................
Features .........................................
Standard mode/power mode ..........
Traveling distance ..........................
Effective use of the battery .............
Battery level ....................................
3-1
3-1
3-1
3-2
3-3
3-4
INSTRUMENT AND CONTROL
FUNCTIONS ....................................... 4-1
Beeper ............................................ 4-1
Main switch/steering lock ................ 4-1
Multi-function display ...................... 4-2
Using the security lock .................... 4-7
Handlebar switches ...................... 4-11
Front brake lever .......................... 4-11
Rear brake lever ........................... 4-11
Seat .............................................. 4-12
Helmet holder ............................... 4-12
Luggage hook ............................... 4-13
Grab bar ....................................... 4-13
FOR YOUR SAFETY –
PRE-OPERATION CHECKS ............. 5-1
CHARGING THE BATTERY..............
Battery charging location ................
Charging procedure .......................
Charging time .................................
Display of charging progress
status ..........................................
About the battery ............................
OPERATION AND IMPORTANT
RIDING POINTS.................................
Preparations for starting off ............
Starting off ......................................
Acceleration and deceleration ........
Braking ...........................................
Parking ...........................................
PERIODIC MAINTENANCE AND
ADJUSTMENT ...................................
General maintenance and
lubrication chart ..........................
Checking for irregular motor
sounds ........................................
Checking the accelerator grip ........
Tires ...............................................
Cast wheels ....................................
Adjusting the front and rear
brake lever free play ...................
6-1
6-1
6-3
6-8
6-9
6-9
7-1
7-1
7-3
7-4
7-5
7-5
8-1
8-2
8-4
8-4
8-5
8-6
8-6
Checking the front and rear brake
shoes ........................................... 8-8
Checking and lubricating the
cables .......................................... 8-8
Lubricating the front and rear
brake levers ................................. 8-9
Checking and lubricating the
centerstand .................................. 8-9
Checking the front fork .................. 8-10
Checking the steering ................... 8-10
Checking the wheel bearings ........ 8-11
Replacing the headlight bulb ........ 8-11
Replacing the tail/brake light
bulb ............................................ 8-12
Replacing a turn signal light
bulb ............................................ 8-13
Checking the charging cord and
charging plug ............................. 8-14
Troubleshooting ............................ 8-15
SCOOTER CARE AND STORAGE.... 9-1
Matte color caution ......................... 9-1
Care ................................................ 9-1
Storage ........................................... 9-3
SPECIFICATIONS ........................... 10-1
CONSUMER INFORMATION........... 11-1
Identification numbers ................... 11-1
1CB-9-E0.book 1 ページ
2010年10月15日 金曜日 午前10時19分
SAFETY INFORMATION
EAU50653
Be a Responsible Owner
As the vehicle’s owner, you are responsible for the safe and proper operation
of your scooter.
Scooters are single-track vehicles.
Their safe use and operation are dependent upon the use of proper riding
techniques as well as the expertise of
the operator. Every operator should
know the following requirements before
riding this scooter.
He or she should:
 Obtain thorough instructions from
a competent source on all aspects
of scooter operation.
 Observe the warnings and maintenance requirements in this Owner’s Manual.
 Obtain qualified training in safe
and proper riding techniques.
 Obtain professional technical service as indicated in this Owner’s
Manual and/or when made necessary by mechanical conditions.
Safe Riding
Perform the pre-operation checks each
time you use the vehicle to make sure it
is in safe operating condition. Failure to
inspect or maintain the vehicle properly
increases the possibility of an accident
or equipment damage. See page 5-1
for a list of pre-operation checks.
 This scooter is designed to carry
the operator only. No passengers.
 The failure of motorists to detect
and recognize scooters in traffic is
the predominating cause of automobile/scooter accidents. Many
accidents have been caused by an
automobile driver who did not see
the scooter. Making yourself conspicuous appears to be very effective in reducing the chance of this
type of accident.
Therefore:
• Wear a brightly colored jacket.
• Use extra caution when you are
approaching
and
passing
through intersections, since intersections are the most likely
places for scooter accidents to
occur.
• Ride where other motorists can
1-1
see you. Avoid riding in another
motorist’s blind spot.
 Many accidents involve inexperienced operators. In fact, many operators who have been involved in
accidents do not even have a current driver’s license.
• Make sure that you are qualified
and that you only lend your
scooter to other qualified operators.
• Know your skills and limits.
Staying within your limits may
help you to avoid an accident.
• We recommend that you practice riding your scooter where
there is no traffic until you have
become thoroughly familiar with
the scooter and all of its controls.
 Many accidents have been caused
by error of the scooter operator. A
typical error made by the operator
is veering wide on a turn due to excessive speed or undercornering
(insufficient lean angle for the
speed).
• Always obey the speed limit and
never travel faster than warrant-
1
1CB-9-E0.book 2 ページ
2010年10月15日 金曜日 午前10時19分
SAFETY INFORMATION
1




ed by road and traffic conditions.
• Always signal before turning or
changing lanes. Make sure that
other motorists can see you.
The posture of the operator is important for proper control. The operator should keep both hands on
the handlebar and both feet on the
operator footrests during operation
to maintain control of the scooter.
Do not place magnets or objects
with a strong magnetic force near
the accelerator grip. In addition, do
not place objects susceptible to
magnetic forces (i.e., credit cards,
watches, etc.) close to the accelerator grip.
Never ride under the influence of
alcohol or other drugs.
This scooter is designed for
on-road use only. It is not suitable
for off-road use.
Avoid submerged roads
Do not ride on flooded roads. Water
could cause power unit failure, electric
leakage, and/or short-circuiting.
Protective Apparel
The majority of fatalities from scooter
accidents are the result of head injuries. The use of a safety helmet is the
single most critical factor in the prevention or reduction of head injuries.
 Always wear an approved helmet.
 Wear a face shield or goggles.
Wind in your unprotected eyes
could contribute to an impairment
of vision that could delay seeing a
hazard.
 The use of a jacket, substantial
shoes, trousers, gloves, etc., is effective in preventing or reducing
abrasions or lacerations.
 Never wear loose-fitting clothes,
otherwise they could catch on the
control levers or wheels and cause
injury or an accident.
 Always wear protective clothing
that covers your legs, ankles, and
feet. The engine or exhaust system become very hot during or after operation and can cause burns.
Loading
Adding accessories or cargo to your
scooter can adversely affect stability
1-2
and handling if the weight distribution of
the scooter is changed. To avoid the
possibility of an accident, use extreme
caution when adding cargo or accessories to your scooter. Use extra care
when riding a scooter that has added
cargo or accessories. Here, along with
the information about accessories below, are some general guidelines to follow if loading cargo to your scooter:
The total weight of the operator, accessories and cargo must not exceed the
maximum load limit. Operation of an
overloaded vehicle could cause an
accident.
Maximum load:
87 kg (192 lb)
When loading within this weight limit,
keep the following in mind:
 Cargo and accessory weight
should be kept as low and close to
the scooter as possible. Securely
pack your heaviest items as close
to the center of the vehicle as possible and make sure to distribute
the weight as evenly as possible
on both sides of the scooter to min-
1CB-9-E0.book 3 ページ
2010年10月15日 金曜日 午前10時19分
SAFETY INFORMATION
imize imbalance or instability.
 Shifting weights can create a sud-
den imbalance. Make sure that accessories and cargo are securely
attached to the scooter before
riding. Check accessory mounts
and cargo restraints frequently.
• Properly adjust the suspension
for your load (suspension-adjustable models only), and
check the condition and pressure of your tires.
• Never attach any large or heavy
items to the handlebar, front
fork, or front fender. Such items
can create unstable handling or
a slow steering response.
 This vehicle is not designed to
pull a trailer or to be attached to
a sidecar.
Genuine Yamaha Accessories
Choosing accessories for your vehicle
is an important decision. Genuine
Yamaha accessories, which are available only from a Yamaha dealer, have
been designed, tested, and approved
by Yamaha for use on your vehicle.
Many companies with no connection to
Yamaha manufacture parts and accessories or offer other modifications for
Yamaha vehicles. Yamaha is not in a
position to test the products that these
aftermarket
companies
produce.
Therefore, Yamaha can neither endorse nor recommend the use of accessories not sold by Yamaha or
modifications not specifically recommended by Yamaha, even if sold and
installed by a Yamaha dealer.
Aftermarket Parts, Accessories,
and Modifications
While you may find aftermarket products similar in design and quality to
genuine Yamaha accessories, recognize that some aftermarket accessories
or modifications are not suitable because of potential safety hazards to you
or others. Installing aftermarket products or having other modifications performed to your vehicle that change any
of the vehicle’s design or operation
characteristics can put you and others
at greater risk of serious injury or death.
You are responsible for injuries related
to changes in the vehicle.
Keep the following guidelines in mind,
1-3
as well as those provided under “Loading” when mounting accessories.
 Never install accessories or carry
cargo that would impair the performance of your scooter. Carefully
inspect the accessory before using
it to make sure that it does not in
any way reduce ground clearance
or cornering clearance, limit suspension travel, steering travel or
control operation, or obscure lights
or reflectors.
• Accessories fitted to the handlebar or the front fork area can
create instability due to improper
weight distribution or aerodynamic changes. If accessories
are added to the handlebar or
front fork area, they must be as
lightweight as possible and
should be kept to a minimum.
• Bulky or large accessories may
seriously affect the stability of
the scooter due to aerodynamic
effects. Wind may attempt to lift
the scooter, or the scooter may
become unstable in cross
winds. These accessories may
also cause instability when
1
1CB-9-E0.book 4 ページ
2010年10月15日 金曜日 午前10時19分
SAFETY INFORMATION
1
passing or being passed by
large vehicles.
• Certain accessories can displace the operator from his or
her normal riding position. This
improper position limits the freedom of movement of the operator and may limit control ability,
therefore, such accessories are
not recommended.
 Use caution when adding electrical accessories. If electrical accessories exceed the capacity of the
scooter’s electrical system, an
electric failure could result, which
could cause a dangerous loss of
lights or motor power.
Aftermarket Tires and Rims
The tires and rims that came with your
scooter were designed to match the
performance capabilities and to provide
the best combination of handling, braking, and comfort. Other tires, rims, sizes, and combinations may not be
appropriate. Refer to page 8-5 for tire
specifications and more information on
replacing your tires.
Transporting the Scooter
Be sure to observe following instructions before transporting the scooter in
another vehicle.
 Remove all loose items from the
scooter.
 Point the front wheel straight
ahead on the trailer or in the truck
bed, and choke it in a rail to prevent movement.
 Secure the scooter with tie-downs
or suitable straps that are attached
to solid parts of the scooter, such
as the frame or upper front fork triple clamp (and not, for example, to
rubber-mounted handlebars or
turn signals, or parts that could
break). Choose the location for the
straps carefully so the straps will
not rub against painted surfaces
during transport.
 The suspension should be compressed somewhat by the
tie-downs, if possible, so that the
scooter will not bounce excessively during transport.
Further safe-riding points
 Make sure to signal clearly when
making turns.
 Braking can be extremely difficult





1-4
EAUT2030
on a wet road. Avoid hard braking,
because the scooter could slide.
Apply the brakes slowly when
stopping on a wet surface.
Slow down as you approach a corner or turn. Once you have completed a turn, accelerate slowly.
Be careful when passing parked
cars. A driver might not see you
and open a door in your path.
Railroad crossings, streetcar rails,
iron plates on road construction
sites, and manhole covers become extremely slippery when
wet. Slow down and cross them
with caution. Keep the scooter upright, otherwise it could slide out
from under you.
The brake lining could get wet
when you wash the scooter. After
washing the scooter, check the
brakes before riding.
Always wear a helmet, gloves,
trousers (tapered around the cuff
1CB-9-E0.book 5 ページ
2010年10月15日 金曜日 午前10時19分
SAFETY INFORMATION
and ankle so they do not flap), and
a bright colored jacket.
 Do not carry too much luggage on
the scooter. An overloaded scooter is unstable.
EAU50823
Charging the battery safely
 Do not charge the battery in areas
potentially exposed to rain or water. This could cause an electric
shock or short circuit.
 Be sure to plug the charging plug
only directly to a grounded electrical outlet with residual-current device (RCD) protection to charge
the battery. If incorrectly grounded,
this could cause an electric shock
or short circuit.
 If the vehicle is damaged due to
overturning or accident, do not
plug in the charging plug to an outlet. This could cause an electric
shock or short circuit. Have your
vehicle checked by a Yamaha
1-5
dealer as soon as possible.
 If the charging cord or charging
plug is damaged, do not plug in to
an outlet. This could cause an
electric shock or short circuit. Have
your vehicle checked by a
Yamaha dealer as soon as possible.
1
1CB-9-E0.book 1 ページ
2010年10月15日 金曜日 午前10時19分
DESCRIPTION
EAU10410
Left view
1
1
2
3
2
7
6
5
1. Main switch/steering lock (page 4-1)
2. Seat lock (page 4-12)
3. Grab bar (page 4-13)
4. Motor housing
5. Rear brake lever free play adjusting nut (page 8-6)
6. Footrest
7. Front brake lever free play adjusting nut (page 8-6)
2-1
4
1CB-9-E0.book 2 ページ
2010年10月15日 金曜日 午前10時19分
DESCRIPTION
EAU10420
Right view
1 2
3
2
3
4
5
6
7
5
8
4
1. Charging cord (page 6-4)
9
2. Seat (page 4-12)
3. Luggage hook (page 4-13)
4. Footrest
5. Centerstand (page 8-9)
2-2
1CB-9-E0.book 3 ページ
2010年10月15日 金曜日 午前10時19分
DESCRIPTION
EAU10430
Controls and instruments
1
1
2
4
3
2
3
4
5
6
7
5
8
9
1. Rear brake lever (page 4-11)
2. Handlebar switches (page 4-11)
3. Multi-function display (page 4-2)
4. Front brake lever (page 4-11)
5. Accelerator grip (page 8-4)
2-3
1CB-9-E0.book 1 ページ
2010年10月15日 金曜日 午前10時19分
EC-03 FEATURES
Features
EAU50470
The features of the EC-03 are following:
 The driving power source is only
electricity and there is no need for
fuel supply or engine oil change.
 High performance motor with
greatly reduced noise and vibration providing a pleasant ride.
 Charging the vehicle can be done
via a grounded electrical outlet
with residual-current device (RCD)
protection.
EAU50322
Standard mode/power mode
1
The motor driving power can be selected according to riding conditions, road
conditions, etc.
The standard mode is suitable for normal riding, while the power mode provides more comfortable riding when
ascending hills.
Switching the mode
Pushing button 1 “POWER” switches
between the standard mode and the
power mode.
2
3
1. Power mode indicator “POWER”
When the power mode indicator “POWER” is displayed, the vehicle is set to
the power mode. When the power
mode indicator “POWER” is not displayed, the vehicle is set to the standard mode.
TIP
The mode that is currently set is stored
in memory even if the key is turned to
“OFF”.
Choosing the mode
Referring to the table below, choose
the mode according to the riding conditions. The standard mode consumes
less battery power so that the distance
3-1
4
5
6
7
8
9
1CB-9-E0.book 2 ページ
2010年10月15日 金曜日 午前10時19分
EC-03 FEATURES
traveled on a single charge increases.
1
Mode
2
Starting off
Applicable Flat road
conditions Ascending
3
Descending
4
5
6
7
8
9
Power* Standard
: Recommended mode for effective
operation
: Less effective operation than the
power mode
: Distance traveled is shorter than
the standard mode
Traveling distance
EAU50332
TIP
The distance that can be traveled on a
single charge varies according to the
riding and road conditions.
These conditions include the number of
starts and stops, vehicle load, the
steepness of slopes, road conditions,
wind direction and velocity, ambient
temperature, charging status, decreased battery performance, and low
tire air pressure.
Distance traveled on a single
charge
The data in the following chart was
measured at Yamaha Motor Co., Ltd. It
was measured when traveling with a
new battery at an ambient temperature
and vehicle load (total weight of rider
and luggage) as shown below on a dry
road surface in the absence of wind.
TIP
The maximum slope ascending capacity is a gradient of approximately 16%
(about 9 degrees).
 The distance that can be traveled
becomes shorter when continu3-2
1CB-9-E0.book 3 ページ
2010年10月15日 金曜日 午前10時19分
EC-03 FEATURES
ously riding in the power mode as
compared with riding in the standard mode.
 Because of the battery character,
the riding distance might be reduced according to the ambient
temperature due to changes of the
battery temperature.
 The distance that can be traveled
becomes 5–10% shorter when the
vehicle load is increased 10 kg.
EAU50342
Effective use of the battery
If the battery is left nearly fully charged
(4–5 segments shown on the battery
charge indicator) and exposed to high
temperature for an extended period, it
will rapidly deplete. To extend the battery life, handle as follows:
 Choose a cool place with no direct
sunlight when charging the battery.
 Do not store the battery with a
charge less than 20% (below the
last segment of the battery level indicator) for an extended period of
time.
 Choose a cool and well-ventilated
place without direct sunlight for
storing the vehicle.
 When not used for a long period of
time, charge the battery until the
2–3 segments of the battery
charge indicator are shown and
then store the vehicle in a cool
place
(optimum
temperature
15 C – 25 C). Check the battery
level while the vehicle is in storage.
If the battery level drops to the last
segment, recharge the battery until
3-3
2–3 segments of the battery
charge indicator are shown.
ECA17071
NOTICE
If the battery is discharged until the
battery is depleted, recharging will
not be possible and the battery will
not be usable.
Depleting battery image
Using at normal
temperature
Battery
capacity
(%)
Using at high
temperature
2
3
4
5
6
7
Period of use
8
9
1CB-9-E0.book 4 ページ
2010年10月15日 金曜日 午前10時19分
EC-03 FEATURES
Battery level
1
EAU50351
TIP
Be sure to check the battery level before each ride.
2
3
4
5
6
7
8
9
Checking the battery level
Check the number of segments displayed in the battery level indicator.
TIP
While charging the battery, the indicator shows the progress status of charging. This differs from the indication of
remaining charge when the vehicle is in
use. See page 6-9.
1
1. Battery level indicator
Battery level indicator
When the key is turned to “ON”, all segments of the battery level indicator
come on for a few seconds, and then
show a general indication of the remaining battery charge corresponding
to the amount of the electric output.
3-4
1CB-9-E0.book 5 ページ
2010年10月15日 金曜日 午前10時19分
EC-03 FEATURES
Battery level reference table
Lit
Battery level
(%)
Flashing
Battery level indicator
in the display
What to do
2
OK. Go ahead with riding.
3
OK. Go ahead with riding.
The 4th segment flashes to indicate that the remaining battery charge is now above
half level.
4
5
OK. Go ahead with riding.
Decreased ability to ascend slopes.
Charge the battery.
The last segment flashes and the beeper sounds to indicate that the remaining battery
charge is now about 10%.
Stop riding immediately and charge the battery.
There is no battery charge left and it is impossible to ride.
Charge the battery immediately.
This symbol may not be displayed depending on the battery condition.
3-5
6
7
8
9
1CB-9-E0.book 1 ページ
2010年10月15日 金曜日 午前10時19分
INSTRUMENT AND CONTROL FUNCTIONS
Beeper
1
2
3
4
5
6
EAU49982
The EC-03 informs you of the following
operations and status of the vehicle using the beeper.
 Key in “ON” position
 Standby mode (See page 7-2.)
 A control button is pushed
 Security lock unlocked
 Security lock unlock failed
 Enters the riding mode (see
page 4-6).
 Turn signals in use
 Battery level is approx. 10% (See
page 3-5.)
 Battery charging started
Main switch/steering lock
OFF
EAU10460
ON
EAU10661
OFF
All electrical systems are off. The key
can be removed.
EWA10061
LOCK
The main switch/steering lock controls
the ignition and lighting systems, and is
used to lock the steering. The various
positions are described below.
8
9
WARNING
Never turn the key to “OFF” or
“LOCK” while the vehicle is moving.
Otherwise the electrical systems will
be switched off, which may result in
loss of control or an accident.
EAU10683
EAU50000
7
key to “OFF” and then back to “ON”
again.
ON
All electrical systems are supplied with
power, and the headlight, meter lighting
and taillight come on. The key cannot
be removed.
TIP
To protect the battery, the EC-03 is
equipped with an auto-off function. The
power stops automatically if the vehicle
is stopped for more than five minutes.
To cancel the auto-off function, turn the
4-1
LOCK
The steering is locked, and all electrical
systems are off. The key can be removed.
1CB-9-E0.book 2 ページ
2010年10月15日 金曜日 午前10時19分
INSTRUMENT AND CONTROL FUNCTIONS
To lock the steering
To unlock the steering
Multi-function display
EAU50023
EWA12312
2
2
1
1. Push.
1. Push.
2. Turn.
2. Turn.
1. Turn the handlebars all the way to
the left.
2. Push the key in from the “OFF” position, and then turn it to “LOCK”
while still pushing it.
3. Remove the key.
1
WARNING
Be sure to stop the vehicle before
making any setting changes to the
multi-function display. Changing
settings while riding can distract the
operator and increase the risk of an
accident.
2
3
4
Push the key in, and then turn it to
“OFF” while still pushing it.
5
6
7
8
9
4-2
1CB-9-E0.book 3 ページ
2010年10月15日 金曜日 午前10時19分
INSTRUMENT AND CONTROL FUNCTIONS
10
9
1
2
8
1
7
2
3
3
4
nosis device for the battery and control
unit. When the key is turned to “ON”,
the self-diagnosis starts automatically
and all of the display segments of the
multi-function meter appear. Once the
self-diagnosis is completed, the display
automatically changes to the standby
mode. When in the standby mode,
“PUSH” starts flashing.
6
2. Button 2 “SET”
5
3. Button 3 “SELECT”
5
When the vehicle is in the riding mode,
the operating status indicator “RUN”
and the ready indicators appear.
6
1. Power mode indicator “POWER”
2. Warning mark “
1
”
3. Speed warning indicator “SPEED”
8
2
3
1. Button 1 “POWER”
4
7
1
4. Tripmeter/odometer/temperature warning
display “Trip”/“Odo”/“HEAT”
2
Push any of the following buttons to enter the riding mode.
5. Control buttons
9
6. Warning light
7. Battery level indicator
8. Operating status indicator “RUN”
9. Security lock indicator “
LOCK”
10.Speedometer
1. Operating status indicator “RUN”
The EC-03 is equipped with a self-diag-
2. Ready indicators
4-3
1CB-9-E0.book 4 ページ
2010年10月15日 金曜日 午前10時19分
INSTRUMENT AND CONTROL FUNCTIONS
TIP
When the vehicle is in the riding mode,
the beeper sounds. The beeper stops
when either brake lever is squeezed or
the vehicle starts moving.
Control buttons
Button 1 “POWER”
Button 2 “SET”
Button 3 “SELECT”
The following operations and settings
are made using these buttons.
 Changing from the standby mode
to the riding mode
 Switching between the standard
mode and the power mode
 Switching between the odometer
and the tripmeter
 Resetting the tripmeter
 Registering or changing the security number
 Locking and unlocking the security
lock
Speedometer
The speedometer shows the riding
speed.
Tripmeter “Trip”
The tripmeter shows the distance traveled since it was last set to zero. To reset the tripmeter, push and hold button
3 “SELECT” for a few seconds until
“0.0” is displayed.
Odometer “Odo”
Push button 3 “SELECT” for at least
one second to switch the display to the
odometer.
The odometer shows the total distance
traveled. Use the odometer as a reference for the intervals between performing periodic maintenance.
Push button 3 for at least one second to
switch the display to the tripmeter.
Temperature warning display
“HEAT”/“COOL”
The EC-03 is equipped with a temperature protection function to protect the
battery and control unit.
If a problem is detected, the tripmeter/
odometer display is canceled and
“COOL” or “HEAT” flash.
 When the temperature of the battery or control unit exceeds a specified temperature, “HEAT” flashes.
4-4
 When the temperature of the bat-
tery falls below a specified temperature, “COOL” flashes.
TIP
 When the temperature of the bat-




tery exceeds a specified temperature, “HEAT” flashes and the
driving power is reduced to limit
the electric output from the battery,
but this is normal.
When the temperature of the battery falls below a specified temperature, “COOL” flashes and the
driving power is reduced to limit
the electric output from the battery,
but this is normal.
If the vehicle is ridden for an extended period in high temperatures, “HEAT” may flash and the
riding speed may be reduced.
If the vehicle is ridden after it has
been left in a hot place or under direct sunlight, “HEAT” may flash
and the riding speed may be reduced.
If the vehicle is ridden after it has
been left in an excessively cold
place (less than 0 C), “COOL”
2
3
4
5
6
7
8
9
1CB-9-E0.book 5 ページ
2010年10月15日 金曜日 午前10時19分
INSTRUMENT AND CONTROL FUNCTIONS
1
2
3
4
5
6
7
8
9
may flash and the riding speed
may be reduced.
 When the battery level indicator
shows less than two segments, if
the vehicle is exposed to higher
temperatures, “COOL” may flash
and the riding speed may be reduced.
 When riding on a long uphill
stretch, “HEAT” may flash and the
riding speed may be reduced.
 When riding on a long uphill
stretch, the temperature of the
control unit may rise and “HEAT”
may flash. If you ride continually,
the operating status indicator
“RUN” goes off to protect the control unit and further riding may be
impossible, but this is not a malfunction.
The vehicle can be ridden when the operating status indicator “RUN” appears
in the display, however riding speed
may be reduced. This is due to reduced
electric output from the battery because of high battery temperature.
1
1
2
1. Operating status indicator “RUN”
2. Temperature indicator “HEAT”
If the battery level indicator shows less
than two segments, or the electric output from the battery is limited because
of the battery temperature, the riding
power is substantially reduced, but this
is not a malfunction.
When the battery and control unit have
reached their normal operating temperature and the operating status indicator
“RUN” appears, the temperature warning display automatically changes back
to the tripmeter/odometer display.
If the operating status indicator “RUN”
does not appear, the vehicle cannot be
ridden.
4-5
1. Tripmeter/odometer
Turn the key to “OFF” and allow the
battery and control unit to cool down
before riding again.
TIP
When the operating status indicator
“RUN” disappears and riding cannot be
continued, the temperature warning
display can be canceled by turning the
key to “OFF” and then back to “ON” after the battery and control unit have
cooled down.
EWA15630
WARNING
Before pushing or moving the
EC-03, be sure to turn the key to
“OFF”. The vehicle may suddenly
1CB-9-E0.book 6 ページ
2010年10月15日 金曜日 午前10時19分
INSTRUMENT AND CONTROL FUNCTIONS
start to move if the accelerator grip
is turned while the key is turned to
“ON”.
Speed warning indicator “SPEED”
If the vehicle speed exceeds 45 km/h,
the speed warning indicator appears
and the warning light flashes.
Operating status indicator “RUN”
This indicator appears when the vehicle can be ridden.
Battery level indicator
This indicator shows the remaining battery charge.
When only one battery indicator segment remains, recharge the battery as
soon as possible. (See page 3-4 for
more information about the battery level.)
2
1
2
1
1. Battery level indicator
TIP
Make sure that the battery is sufficiently
charged before riding.
If the self-diagnosis detects a problem
with the battery, the warning light
comes on, the warning mark “
” appears, and all segments of the battery
level indicator flash. The electric output
from the battery may also be reduced.
3
3
1. Battery level indicator
2. Warning light
3. Warning mark “
”
The vehicle can still be ridden, but it
must be checked by a Yamaha dealer
as soon as possible.
Power mode indicator “POWER”
This indicator comes on when the vehicle is set to the power mode. (See
“Switching the mode” on page 3-1 for
switching the display between the standard mode and the power mode.)
Warning light
This warning light comes on or flashes
as follows:
4-6
4
5
6
7
8
9
1CB-9-E0.book 7 ページ
2010年10月15日 金曜日 午前10時19分
INSTRUMENT AND CONTROL FUNCTIONS
1
2
3
4
5
6
7
8
9
Speed warning indicator
The warning light flashes when vehicle
speed exceeds 45 km/h. At the same
time, the speed warning indicator
“SPEED” appears.
Error warnings
If a problem is detected, the warning
light comes on. In this case, check for
the warning mark “
”. If this warning
mark also appears, have a Yamaha
dealer check the vehicle.
Using the security lock
EAU50033
The EC-03 is equipped with a security
lock that can be used by registering a
security number. Once the security
number has been set, the vehicle cannot be ridden unless the correct security number is entered, even if the key is
turned to “ON”.
ters the standby
“PUSH” flashes.
mode
and
1
Registering and changing the security number
EWA15610
Warning mark “
”
This warning mark flashes if a problem
is detected. If the warning mark keeps
flashing after turning the key to “OFF”
and then back to “ON”, have a Yamaha
dealer check the vehicle.
WARNING
Be sure to stop the vehicle before
registering or changing the security
number. Changing settings while
riding can distract the operator and
increase the risk of an accident.
TIP
After turning the key to “ON”, the warning mark appears. If the warning mark
goes out after a few seconds, there is
no malfunction. Go ahead with riding.
TIP
The security number registration/
change mode is canceled if the registering procedure is not completed in
one minute. If the mode cancels, repeat
the procedure.
1. Turn the key to “ON”.
All display segments appear for a
few seconds, then the vehicle en4-7
1. Security lock indicator “
LOCK”
TIP
When the security lock has been
locked, the security number indicator
“ LOCK” appears when the vehicle is
in the standby mode.
2. Change to the riding mode by
pushing any of the buttons.
1CB-9-E0.book 8 ページ
2010年10月15日 金曜日 午前10時19分
INSTRUMENT AND CONTROL FUNCTIONS
1
2
3
1. Button 1 “POWER”
2. Button 2 “SET”
3. Button 3 “SELECT”
The display shows that the vehicle
is in the riding mode.
to unlock the security lock. (See
page 7-1 for more information
about unlocking the security
lock.)
 When the vehicle enters the riding
mode, the beeper sounds. The
beeper stops sounding when either brake lever is squeezed or the
vehicle starts moving.
3. Press buttons 2 and 3 simultaneously.
The display changes to the security lock registration mode.
Registering the security number
for the first time
Proceed to step 5.
2
3
1
2
1. Input number indicator “– – – – –”
2. Registered number indicator “OLD”
4. Use the buttons to enter the registered security number.
4
5
6
7
Changing the security number
“OLD” and “– – – – –” are displayed.
8
9
Proceed to step 5 if the correct security number is entered.
If an incorrect number is entered,
the beeper sounds, “NG” flashes
TIP
 When the security lock is locked,
after changing to the riding
mode, enter the security number
4-8
1CB-9-E0.book 9 ページ
2010年10月15日 金曜日 午前10時19分
INSTRUMENT AND CONTROL FUNCTIONS
1
a security number.
for a few seconds, and the vehicle
returns to the riding mode. Repeat
the procedure from step 3.
When a four-digit security number
has been entered, “OK or NG” is
displayed.
2
3
1
4
5
1. Input number indicator “– – – – –”
1
1. Incorrect number indicator “NG”
6
2
5. “NEW” and “– – – – –” are displayed.
2. New number indicator “NEW”
Enter a new security number.
The security number consists of a
four-digit number. Enter a number
using the buttons.
6. Push button 3 “SELECT” to display
“OK”.
7
8
9
1
TIP
The number “1111” cannot be used as
4-9
1. Number confirmation indicator “OK”
1CB-9-E0.book 10 ページ
2010年10月15日 金曜日 午前10時19分
INSTRUMENT AND CONTROL FUNCTIONS
7. Push button 2 “SET”. The security
number flashes for a few seconds,
and then the vehicle enters the
riding mode.
Locking and unlocking the security
lock
Locking the security lock
Push button 2 “SET” for a few seconds.
When the security lock is locked, the
security lock indicator “ LOCK” is displayed.
security number. (See “Preparations
for starting off” on page 7-1.)
2
3
1
4
5
TIP
6
 Be sure to record the security
number and keep it in a safe place.
 Pushing button 3 “SELECT”
switches the display between “OK”
and “NG”.
 To change the registered security
number, switch the display to “NG”
by pushing button 3 “SELECT”,
and then push button 2 “SET”. Repeat the procedure from step 5.
7
1. Security lock indicator “
LOCK”
TIP
Do not lock the security lock when having a Yamaha dealer perform service or
repairs on the vehicle.
Unlocking the security lock
Change to the standby mode by pushing one of the buttons, then enter the
4-10
8
9
1CB-9-E0.book 11 ページ
2010年10月15日 金曜日 午前10時19分
INSTRUMENT AND CONTROL FUNCTIONS
Handlebar switches
1
EAU12348
EAU12900
Front brake lever
Left
1
Rear brake lever
EAU12950
1
2
3
1
4
2
5
6
1. Turn signal switch “
2. Horn switch “
1. Front brake lever
/
”
”
EAU12460
7
8
9
Turn signal switch “ / ”
To signal a right-hand turn, push this
switch to “ ”. To signal a left-hand
turn, push this switch to “ ”. When released, the switch returns to the center
position. To cancel the turn signal
lights, push the switch in after it has returned to the center position.
1. Rear brake lever
The front brake lever is located on the
right handlebar grip. To apply the front
brake, pull this lever toward the handlebar grip.
EAU12500
Horn switch “
”
Press this switch to sound the horn.
4-11
The rear brake lever is located on the
left handlebar grip. To apply the rear
brake, pull this lever toward the handlebar grip.
1CB-9-E0.book 12 ページ
2010年10月15日 金曜日 午前10時19分
INSTRUMENT AND CONTROL FUNCTIONS
EAUT3170
Seat
Helmet holder
The helmet holder is located under the
seat. A helmet holding cable is provided under the seat to secure a helmet to
the helmet holder.
To open the seat
1. Place the vehicle on the centerstand.
2. Insert the key in the lock, and then
turn it clockwise.
1
EAU50060
To close the seat
1. Fold the seat down, and then push
it down to lock it in place.
2. Remove the key.
TIP
Make sure that the seat is properly secured before riding.
To secure a helmet to the helmet
holder
1. Open the seat. (See page 4-12.)
2. Pass the helmet holding cable
through the buckle on the helmet
strap as shown, and then hook the
end of the helmet holding cable
over the helmet holder.
2
3
4
5
6
1
7
1. Unlock.
2
3. Fold the seat up.
8
9
1. Helmet holding cable
2. Helmet holder
3. Securely
close
the
seat.
WARNING! Never ride with a
4-12
1CB-9-E0.book 13 ページ
2010年10月15日 金曜日 午前10時19分
INSTRUMENT AND CONTROL FUNCTIONS
1
2
3
4
helmet attached to the helmet
holder, since the helmet may hit
objects, causing loss of control
and possibly an accident.[EWA10161]
To release the helmet from the helmet holder
Open the seat, remove the helmet
holding cable from the helmet holder
and the helmet, and then close the
seat.
Luggage hook
EAUT1072
EWAT1031
WARNING
 Do not exceed the load limit of
1 kg (2 lb) for the luggage hook.
 Do not exceed the maximum
load of 87 kg (192 lb) for the vehicle.
Grab bar
Hold the grab bar with your right hand
to place the vehicle on the centerstand.
1
5
1. Grab bar
6
1
7
8
1. Luggage hook
9
4-13
EAU29910
1CB-9-E0.book 1 ページ
2010年10月15日 金曜日 午前10時19分
FOR YOUR SAFETY – PRE-OPERATION CHECKS
EAU15596
Inspect your vehicle each time you use it to make sure the vehicle is in safe operating condition. Always follow the inspection
and maintenance procedures and schedules described in the Owner’s Manual.
EWA11151
WARNING
Failure to inspect or maintain the vehicle properly increases the possibility of an accident or equipment damage.
Do not operate the vehicle if you find any problem. If a problem cannot be corrected by the procedures provided in
this manual, have the vehicle inspected by a Yamaha dealer.
Before using this vehicle, check the following points:
ITEM
Front brake
Rear brake
Control cables
Wheels and tires
Brake levers
Centerstand
Chassis fasteners
CHECKS
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Check operation.
Lubricate cable if necessary.
Check lever free play.
Adjust if necessary.
Check operation.
Lubricate cable if necessary.
Check lever free play.
Adjust if necessary.
Make sure that operation is smooth.
Lubricate if necessary.
Check for damage.
Check tire condition and tread depth.
Check air pressure.
Correct if necessary.
Make sure that operation is smooth.
Lubricate lever pivoting points if necessary.
Make sure that operation is smooth.
Lubricate pivot if necessary.
Make sure that all nuts, bolts and screws are properly tightened.
Tighten if necessary.
5-1
2
3
PAGE
4
8-6, 8-8
5
6
8-6, 8-8
7
8-8
8
8-5, 8-6
9
8-9
8-9
—
1CB-9-E0.book 2 ページ
2010年10月15日 金曜日 午前10時19分
FOR YOUR SAFETY – PRE-OPERATION CHECKS
ITEM
1
Instruments, lights, signals
and switches
CHECKS
• Check operation.
• Correct if necessary.
PAGE
—
2
3
4
5
6
7
8
9
5-2
1CB-9-E0.book 1 ページ
2010年10月15日 金曜日 午前10時19分
CHARGING THE BATTERY
Yamaha dealer check the vehicle.
EAU50560
EWA15760




WARNING
If the vehicle is damaged due to
overturning or accident, do not
plug in the charging plug to the
outlet. Otherwise it could cause
an electric shock or short circuit. Have a Yamaha dealer
check the charging plug before
charging the battery.
Charge the vehicle where no
rain can get to it, as this could
cause an electric shock or short
circuit.
Be sure to plug in the charging
plug to a grounded electrical
outlet with residual-current device (RCD) protection for charging the battery. If grounded
incorrectly, this could cause an
electric shock or short circuit.
Do not remove the plastic cover
under the seat to check the battery or built-in battery charger
as this increases the risk of an
electric shock or short circuit. If
any problem is found, have a
Battery charging location
EAU50383
EWA15872
WARNING
Charging the battery incorrectly can
cause electric shock or fire. Serious
injury or death can occur if you ignore any of the following:
 Read all instructions and labels
before charging the battery.
 Choose a dry location with a
flat, stable surface that is protected from rain or water spray.
The area must have good ventilation and be free of flammable
objects or sources of heat.
 Be sure the vehicle, charging
cord, and charging plug will not
be disturbed by children or other bystanders, or animals.
 Connect the charging plug only
directly to a grounded electrical
outlet with residual-current device (RCD) protection. Do not
use an ungrounded extension
cord or multi-outlet plug with
the charging cord.
 If your vehicle has been damaged due to overturn or acci-
1
1. Plastic cover
6-1
2
3
4
5
6
7
8
9
1CB-9-E0.book 2 ページ
2010年10月15日 金曜日 午前10時19分
CHARGING THE BATTERY
1
dent, do not plug in the charging
cord.
Have
your
vehicle
checked by a Yamaha dealer as
soon as possible.
2
3
4
posed to direct sunlight or near
a heater.
 Do not charge when there is risk
of thunderstorms or lightning.
Electrical surges could cause
damage.
 Do not use the AC outlet of a car
or generator for charging the
battery as this could cause a
malfunction.
Park the vehicle on a flat, stable surface near a grounded electrical outlet
with residual-current device (RCD) protection. The area must be dry and, if
necessary, sheltered to prevent rain
water or other moisture from wetting
the vehicle, charging cord, or outlet.
The environment affects the duration
of battery charging. For optimum
charging, charge the battery out of direct sunlight in an ambient temperature of 15 C – 25 C.
5
6
7
8
9
ECA17451
NOTICE
Improper charging can damage the
battery and built-in battery charger.
 Do not charge in a place ex-
TIP
Although charging between 15 C – 25 C
provides the best results, the battery can
be charged within an ambient temperature range of –5 C – 50 C. A depleted
battery cannot be charged if ambient tem6-2
perature is below 0 C.
Examples of recommended charging locations
A cool, shaded and well-ventilated
place.
A place that does not fall below –5 C
overnight.
1CB-9-E0.book 3 ページ
2010年10月15日 金曜日 午前10時19分
CHARGING THE BATTERY
Examples of unsuitable charging
locations
Charging in a place exposed to direct
sunlight or near a heater.
Charging procedure
EWA15691


Charging in cold places such as in a
storage shed, outdoors or in the winter.
EAU50394


WARNING
Do not handle the charging plug
with wet hands. You could be
electrocuted.
Do not charge the battery if any
damage, corrosion, rust or
looseness is found with the
charging plug, charging cord or
grounded electrical outlet. This
could cause a fire, electric
shock or short circuit.
If any unusual odor or smoke
emerges from the vehicle during charging, stop charging the
battery immediately and consult
your Yamaha dealer.
Electromagnetic waves emitted
from the battery charger could
interfere with the function of
heart devices or other electrical
medical equipment and cause
injury. If you use an implant-type cardiac pacemaker or
defibrillator, or other electrical
medical device, be sure to consult with your doctor or the
6-3
manufacturer to check whether
being near the battery charger
could affect the device.
2
3
4
EWA15881
WARNING
Do not use the charging cord or
charging plug if damaged (i.e., broken or exposed leads) because it
could cause electric shock or fire. If
such damage is found on the charging cord, stop using it immediately
and have a Yamaha dealer check the
vehicle. Handle the charging cord
carefully by observing the following:
 Do not twist the charging cord,
wrap it into a tight loop, or subject it to sharp bends.
 Be sure the charging cord cannot be caught in a door or win-
5
6
7
8
9
1CB-9-E0.book 4 ページ
2010年10月15日 金曜日 午前10時19分
CHARGING THE BATTERY
dow.
the charging plug.
storing place as shown.
 Do not pull or apply excessive
1
2


3

4
5

6

7

8
9

force to the charging cord.
Do not drop the charging cord
or charging plug or expose it to
strong impact.
Do not secure the charging cord
or charging plug in a place with
sharp objects such as a nail.
Do not step on the charging
cord or charging plug or place
any object on them.
Do not leave the charging cord
or charging plug near a heater
or other source of heat.
Do not modify the charging cord
or charging plug.
Park the vehicle carefully so the
charging cord cannot be
pinched, stepped on, or pulled
accidentally. Also be sure the
vehicle cannot be knocked over
which could stretch or damage
the charging cord or charging
plug.
Do not pull the charging cord to
unplug the charging plug from
the electrical outlet. Pull only
1
Starting charging
1. Place the vehicle on the centerstand.
2. Turn the key to “OFF”.
3. Open the seat. (See page 4-12 for
more information.)
1. Charging plug
2. Charging cord
5. Place the charging cord in one of
the grooves. NOTICE: The charging cord may be damaged if not
placed into a groove before
closing the seat.[ECA17460]
1
4. Grasp the charging plug, and then
unwrap the charging cord from its
6-4
2
1. Groove
1CB-9-E0.book 5 ページ
2010年10月15日 金曜日 午前10時19分
CHARGING THE BATTERY
along with other electrical
equipment which may exceed
the outlet’s amperage and overheat the outlet.
 Be sure to plug in the charging
plug firmly.
6. Close the seat and push down on
the back to lock it in position.
TIP
Before closing the seat, make sure that
nothing is left under it.
7. Remove the key. To help prevent
theft, be sure to lock the steering,
and then remove the key when
charging the battery.
8. Inspect the charging plug for any
damage. Remove any dust, soil,
oil or water with a dry cloth if necessary. Plug the charging plug into
a grounded electrical outlet with
residual-current device (RCD) protection.
1
2
3
1. Charging plug
4
EWA15891
WARNING
To avoid serious injury or death
from electric shock or fire:
 Do not use the charging plug if it
has a damaged or loose prong.
Have a Yamaha dealer check the
vehicle.
 Check the charging plug for any
foreign objects such as dust,
soil, oil or water before charging. If necessary, wipe the plug
clean with a dry cloth.
 Do not use an ungrounded extension cord or a multi-outlet
plug between the charging cord
and the outlet.
 Do not use the electrical outlet
6-5
5
6
7
8
9
9. When the charging plug is plugged
into an electrical outlet, charging
starts automatically. The battery
1CB-9-E0.book 6 ページ
2010年10月15日 金曜日 午前10時19分
CHARGING THE BATTERY
indicator level appears in the display and the beeper sounds. All indicator segments appear for a few
seconds, and the charging
progress status is shown.
1
2
3
1
4
1. Temperature indicator “HEAT”
 If ambient temperature is below
5
6
TIP
 The battery may be above the
7
8
9
maximum 50 C suitable for charging immediately after riding. In this
case, the charger enters a waiting
mode and “HEAT” flashes until the
battery and battery charger reach
the specified temperature. Charging then starts automatically.
–5 C, “COOL” flashes and the
vehicle enters a waiting mode until the battery and battery charger
reach the specified temperature.
Charging then starts automatically.
1
1. Temperature indicator “COOL”
 If the battery is already fully
charged when the charging plug is
plugged in, the display will show
the fully charged status for a few
minutes and then go off. The battery charger will not charge the
battery further.
10. The battery charging status can be
checked in the display. (See page
6-9 for more information about the
charging status display.)
11. Charging can be stopped or restarted by unplugging or plugging
in the charging plug.
TIP
 Only the battery level indicator ap6-6
1CB-9-E0.book 7 ページ
2010年10月15日 金曜日 午前10時19分
CHARGING THE BATTERY
ing plug can be damaged when
closing the seat.[ECA17480]
pears in the display during charging. The display goes off if the
charging plug is unplugged during
charging.
 Even if the key is turned to “ON”,
the vehicle does not enter the
standby mode during charging.
2
1
2
1
3
Completing charging
When the battery is fully charged, the
display goes off automatically after a
few minutes.
1. Grasp the charging plug, and then
unplug it from the electrical outlet.
NOTICE: Do not pull the charging cord to unplug the charging
plug from the electrical outlet.
This could damage the charging
cord.[ECA17470]
1. Charging plug
3
4
2. Open the seat. (See page 4-12 for
more information.)
1. Charging plug
2. Groove
5
3. Charging cord
4. Secure the charging cord by placing it in the holder as shown.
6
7
1
8
3. Hold the charging plug, and while
pressing the charging cord into the
groove, wind it clockwise as
shown. NOTICE: If the charging
cord is not wound properly, the
vehicle, charging cord or charg6-7
9
1. Holder
1CB-9-E0.book 8 ページ
2010年10月15日 金曜日 午前10時19分
CHARGING THE BATTERY
5. Close the seat, and push down on
the back to lock it in position.
1
TIP
 Before closing the seat, make sure
that nothing is left under the seat.
2
 Make sure that the seat is securely
locked before riding.
3
6. Remove the key.
EWA15900
4
5
6
7
8
9
WARNING
When not in use, do not leave the
charging plug plugged into an outlet. Dust or foreign objects could
build up and cause a fire. Be sure to
unplug the charging plug from the
outlet after use.
EAU50402
Charging time
Normal charging
Charging time varies depending on the
riding conditions before charging, remaining battery level, and ambient temperature. It takes approximately seven
hours to charge the battery from a 0%
charged level in the optimum ambient
temperature range of 15 C – 25 C.
100
Battery
level (%)
50
0
2.0
4.0
7.0
Charging time (hours)
TIP
When the charging process is completed, the power from the built-in battery
charger is cut off automatically.
Waiting mode for charging
The vehicle enters a waiting mode if the
6-8
temperature is not suitable for charging
as follows:
 The battery may be above the
maximum 50 C immediately after
riding. In this case, the charger enters a waiting mode and “HEAT”
flashes until the battery and battery charger reach the specified
temperature.
 If ambient temperature is below
–5 C, “COOL” flashes until the
battery and battery charger reach
the specified temperature.
When the temperature is suitable for
charging, charging starts automatically.
1CB-9-E0.book 9 ページ
2010年10月15日 金曜日 午前10時19分
CHARGING THE BATTERY
EAU50411
Display of charging progress
status
The charging process is displayed by
the battery level indicator.
Charging progress
status (%)
0
Charging progress
status in the display
20
20 40
40 60
60 80
About the battery
EAU50425
Lithium-ion (Li-ion) battery
The Li-ion battery used in the EC-03
features high energy density and has a
high voltage (approximately three times
that of nickel-cadmium (Ni-Cd) or nickel-hydrogen (Ni-MH) batteries), meaning it can be made both compact and
lightweight.
Nickel-cadmium and nickel-hydrogen
batteries have a memory effect that
causes electric output capacity to decrease as a result of repeated partial
discharging and charging, so that they
need to have to be completely discharged periodically. Li-ion batteries
can be repeatedly partially charged
without requiring fully discharging.
TIP
80 99
 It is not necessary to use up the
Not displayed
100
Lit
Flashing
battery before charging.
 The electric output capacity decreases over time and use, but the
rate at which it depletes depends
on condition of use.
 The battery discharge may vary
depending on the ambient temper6-9
ature. At low temperatures, the
traveling distance on a single
charge is reduced compared with
normal temperatures and charging
also takes longer. At low temperatures, the electric output capacity
decreases, compared with normal
temperatures, and traveling distance on a single charge is reduced, but this is normal.
 Storing the vehicle in an extremely
hot or cold place could decrease
the electric output capacity.
 Even if the battery is not used, the
battery discharges gradually.
Recycling the battery
Li-ion batteries can be recycled. If the
electric output capacity decreases excessively due to depletion, have a
Yamaha dealer replace the battery. Always follow local regulations regarding
the disposal of batteries.
2
3
4
5
6
7
8
9
1CB-9-E0.book 10 ページ
2010年10月15日 金曜日 午前10時19分
CHARGING THE BATTERY
the accumulated charging amount has
reached 14000 Ah, the battery will no
longer be usable.
1
TIP
 When the battery is replaced with
2
3
4
5
6
7
8
9
Battery depletion
The electric output capacity of the
Li-ion battery used in the EC-03 gradually decreases in the course of use. Although the extent of depletion varies
based on the conditions of use, electric
output capacity typically decreases to
70% of a new battery when having traveled 8000–10000 km for two years.
This is equivalent to charging about
500 times with the condition of riding
16–20 km on a single charge.
a new one, fully charge the battery
once before using it. If the battery
is not fully charged, the battery level indicator does not show the precise battery level.
 At low temperatures such as 0 C,
the electric output capacity decreases by approximately 20%
compared with normal temperature.
 If a depleted battery is used at low
temperatures, the electric output
capacity decreases by approximately 20% compared with normal
temperatures.
Battery electric output auto-stopping function
The battery is equipped with a function
to prevent further use in case of excessive depletion. When eight years have
passed since initial battery charging or
6-10
1CB-9-E0.book 1 ページ
2010年10月15日 金曜日 午前10時19分
OPERATION AND IMPORTANT RIDING POINTS
EAU15951
Read the Owner’s Manual carefully to
become familiar with all controls. If
there is a control or function you do not
understand, ask your Yamaha dealer.
EWA10271
WARNING
Failure to familiarize yourself with
the controls can lead to loss of control, which could cause an accident
or injury.
EAU50092
start moving unexpectedly if the accelerator grip is turned accidentally.
TIP
Make sure the accelerator grip is
closed before starting off. An error
could occur if the accelerator grip is
turned.
3. Put your right foot on the footrest,
and sit on the seat. At the same
time support the vehicle with your
left foot so that the vehicle does
not fall over.
Preparations for starting off
2
3
1. Stand on the left side of the vehicle.
4
5
6
2. While pulling the rear brake lever
with your left hand and holding the
grab bar with your right hand, push
the vehicle off the centerstand.
EWA15660
WARNING
Before placing the vehicle on or
pushing it off the centerstand or sitting on the seat, be sure the key is
“OFF”. Otherwise, the vehicle could
7-1
4. Squeeze the rear brake with your
left hand to prevent the vehicle
from moving.
7
8
9
1CB-9-E0.book 2 ページ
2010年10月15日 金曜日 午前10時19分
OPERATION AND IMPORTANT RIDING POINTS
“
5. Turn the key to “ON”.
LOCK” comes on.
 If the accelerator grip is turned
1
while the vehicle is in the standby
mode, the beeper sounds.
2
6. Cancel the standby mode by
pressing one of the buttons.
1
3
4
2
3
After all displays come on for a few
seconds, the vehicle enters the
standby mode.
5
1. Input number indicator “– – – – –”
1
6
1. Button 1 “POWER”
7
2. Button 2 “SET”
3. Button 3 “SELECT”
8
The vehicle enters the security
lock unlocking mode.
“– – – – –” is displayed.
9
1. Security lock indicator “
LOCK”
TIP
 When the security lock is locked,
the
security
lock
1
indicator
7-2
TIP
If the security lock is not locked, after
canceling the standby mode, the vehicle enters the riding mode. When the
vehicle is in the riding mode, the beeper
sounds. The beeper stops sounding
when either brake lever is squeezed or
the vehicle starts moving. Proceed to
step 8.
7. Enter the security number using
the buttons.
Entering the correct number unlocks the security lock and the vehicle enters the riding mode.
1CB-9-E0.book 3 ページ
2010年10月15日 金曜日 午前10時19分
OPERATION AND IMPORTANT RIDING POINTS
TIP
When the vehicle enters the riding
mode, the beeper sounds. The beeper
stops sounding when either brake lever
is squeezed or the vehicle starts moving.
If the entered security number is
incorrect, the buzzer sounds, “NG”
flashes for a few seconds, and the
vehicle returns to the standby
mode.
curity lock cannot be unlocked even if
the correct security number is entered.
Repeat the procedure after first turning
the key to “OFF” and then back to “ON”
again.
8. Check the battery level indicator to
make sure that the remaining
charged level is sufficient. (See
page 3-4 for more information
about the charge level.)
EAU50103
Starting off
1. Check that the operating status indicator “RUN” is displayed, and
that the vehicle is in the riding
mode.
1
2
2
3
4
5
6
1. Operating status indicator “RUN”
2. Power mode indicator “POWER”
1
1
1. Battery level indicator
1. Incorrect number indicator “NG”
If this occurs, repeat the procedure
from the step 6.
TIP
If an incorrect security number is entered three times in succession, the se-
TIP
If the vehicle is set to the power mode,
the power mode indicator “POWER” is
displayed. (See page 3-1 for more information about switching the display
between the standard mode and the
power mode.)
2. Switch the turn signal on.
7-3
7
8
9
1CB-9-E0.book 4 ページ
2010年10月15日 金曜日 午前10時19分
OPERATION AND IMPORTANT RIDING POINTS
EAU50111
Acceleration and deceleration
1
(b)
2
3
4
5
6
7
8
(a)
TIP
The beeper sounds while the turn signal switch is signaling.
3. Check in front of and behind the
vehicle to make sure that it is safe
to start off.
4. Release the rear brake lever.
5. Check for oncoming traffic, and
then slowly turn the accelerator
grip in order to start off.
6. Push the turn signal switch to cancel the turn signals.
TIP
To protect the battery, the EC-03 is
equipped with an auto-off function. The
power stops automatically if the vehicle
is stopped for more than five minutes.
To restart the vehicle after the vehicle
has been stopped for more than five
minutes, turn the key to “OFF” and then
back to “ON” again.
9
7-4
The speed can be adjusted by opening
and closing the accelerator grip. To increase the speed, turn the accelerator
grip in direction (a). To reduce the
speed, turn the accelerator grip in direction (b).
1CB-9-E0.book 5 ページ
2010年10月15日 金曜日 午前10時19分
OPERATION AND IMPORTANT RIDING POINTS
Braking
EAU50961
Front
Parking
To prevent theft, be sure to lock the
steering and remove the key when
parking. It is recommended to additionally use a chain lock or other type of
motorcycle lock.
EWA10300




WARNING
Avoid braking hard or suddenly
(especially when leaning over to
one side), otherwise the scooter
may skid or overturn.
Railroad crossings, streetcar
rails, iron plates on road construction sites, and manhole
covers become extremely slippery when wet. Therefore, slow
down when approaching such
areas and cross them with caution.
Keep in mind that braking on a
wet road is much more difficult.
Ride slowly down a hill, as braking downhill can be very difficult.
EAU50122
2
EWA15580
Rear
WARNING
Do not park on a slope or on soft
ground, otherwise the vehicle may
overturn.
3
TIP
5
4
 If the vehicle is parked in an ex-
tremely hot or cold place, the temperature protection function may
be activated when the key is
turned to “ON”. If this is activated,
“HEAT” or “COOL” flashes on the
tripmeter/odometer display. (See
page 4-4 “Temperature warning
display” for more information about
the temperature protection function.)
 It is recommended to lock the security lock when parking. (See
page 4-10 for more information
about locking the security lock.)
1. Close the accelerator grip completely.
2. Apply both front and rear brakes
simultaneously while gradually increasing the pressure.
7-5
6
7
8
9
1CB-9-E0.book 1 ページ
2010年10月15日 金曜日 午前10時19分
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU50130
1
2
3
4
5
6
7
8
9
Periodic inspection, adjustment, and lubrication will keep your vehicle in the
safest and most efficient condition possible. Safety is an obligation of the vehicle owner/operator. The most important
points of vehicle inspection, adjustment, and lubrication are explained on
the following pages.
The intervals given in the periodic
maintenance charts should be simply
considered as a general guide under
normal riding conditions. However, depending on the weather, terrain, geographical location, and individual use,
the maintenance intervals may need to
be shortened.
EWA10321
WARNING
Failure to properly maintain the vehicle or performing maintenance activities incorrectly may increase
your risk of injury or death during
service or while using the vehicle. If
you are not familiar with vehicle service, have a Yamaha dealer perform
service.
EWA15840
WARNING
Turn the key to “OFF” when performing maintenance unless otherwise specified. A running motor has
moving parts that can catch on body
parts or clothing and electrical parts
that can cause shocks or fires.
EWA15830
WARNING
This scooter is designed for use on
paved roads only.
EWA15460
WARNING
Brake discs, calipers, drums, and
linings can become very hot during
use. To avoid possible burns, let
brake components cool before
touching them.
8-1
1CB-9-E0.book 2 ページ
2010年10月15日 金曜日 午前10時19分
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU50610
TIP
 The annual checks must be performed every year, except if a kilometer-based maintenance is performed in-
stead.
 From 30000 km, repeat the maintenance intervals starting from 6000 km.
 Items marked with an asterisk should be performed by a Yamaha dealer as they require special tools, data and technical
skills.
3
EAU50620
General maintenance and lubrication chart
NO.
ITEM
1 *
Front brake
2 *
2
Rear brake
3 *
Wheels
4 *
Tires
5 *
Wheel bearings
6 *
Steering bearings
CHECK OR MAINTENANCE JOB
• Check operation and adjust
brake lever free play.
• Replace brake shoes.
• Check operation and adjust
brake lever free play.
• Replace brake shoes.
• Check runout and for damage.
• Check tread depth and for
damage.
• Replace if necessary.
• Check air pressure.
• Correct if necessary.
• Check bearing for looseness or
damage.
• Check bearing play and steering
for roughness.
• Lubricate with
lithium-soap-based grease.
ODOMETER READING
4
1000 km
6000 km
12000 km
18000 km
24000 km
ANNUAL
CHECK
5






6


7
Whenever worn to the limit






Whenever worn to the limit














Every 24000 km
8-2

8

9
1CB-9-E0.book 3 ページ
2010年10月15日 金曜日 午前10時19分
PERIODIC MAINTENANCE AND ADJUSTMENT
NO.
ITEM
1
7 *
Chassis fasteners
2
8
3
4
5
9
10
Centerstand
11 *
Front fork
12 *
13 *
6
7
8
Front brake lever
pivot shaft
Rear brake lever
pivot shaft
14
Shock absorber
assembly
Front and rear
brake switches
Moving parts and
cables
15 *
Accelerator grip
16 *
Lights, signals and
switches
17 *
Motor noise
18 *
Charging cord and
plug
9
ODOMETER READING
6000 km
12000 km
18000 km
24000 km
ANNUAL
CHECK

































• Lubricate.





•
•
•
•
•























CHECK OR MAINTENANCE JOB
1000 km
• Make sure that all nuts, bolts
and screws are properly
tightened.
• Lubricate with
lithium-soap-based grease.
• Lubricate with
lithium-soap-based grease.
• Check operation.
• Lubricate.
• Check operation and for oil
leakage.
• Check operation and shock
absorber for oil leakage.
• Check operation.
Check operation.
Correct if necessary.
Check operation.
Adjust headlight beam.
Check for irregular noise coming
from the motor.
• Correct if necessary.
• Check condition and for
damage.
• Replace if necessary.

8-3
1CB-9-E0.book 4 ページ
2010年10月15日 金曜日 午前10時19分
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU50143
Checking for irregular motor
sounds
Check the motor for irregular sounds.
TIP
The motor cannot be revved beyond a
certain motor speed by turning the accelerator grip when the vehicle is on the
centerstand.
EAU50154
Checking the accelerator grip
Before checking the accelerator grip,
check the following points.
 Make sure that the key is in the
“OFF” position. Turn the accelerator grip slowly and check that it
moves smoothly, and returns
smoothly when released.
 Check for any signs of deterioration or damage around the accelerator grip. Also check the
accelerator grip holder mounting
bolts for tightness.
 When washing the vehicle, avoid
spraying the area around the accelerator grip with water. If the
area around the accelerator grip is
particularly dirty, use a well-wrung
damp cloth to clean.
8-4
EWA15671
WARNING
If a problem is found in accelerator
grip operation, do not operate the
vehicle. Have the vehicle inspected
by a Yamaha dealer. Continuing to
use the vehicle with a problem increases the possibility of an accident or equipment damage.
1. Squeeze the rear brake lever with
your left hand.
2. Turn the key to “ON”.
3. Cancel the standby mode by
pressing one of the control buttons. (See page 4-3.)
4. Make sure that the operating status indicator “RUN” is displayed,
and that the vehicle is in the riding
mode. (See page 7-1 for more information about “Preparations for
starting off” and “Starting off”.)
5. Check that the accelerator grip
and motor operate smoothly when
the vehicle is accelerated by gradually turning the accelerator grip
while riding the vehicle. If there is a
problem, have a Yamaha dealer
check the vehicle.
2
3
4
5
6
7
8
9
1CB-9-E0.book 5 ページ
2010年10月15日 金曜日 午前10時19分
PERIODIC MAINTENANCE AND ADJUSTMENT
Tires
1
2
3
4
5
6
7
8
9
EAU50673
Tire inspection
To maximize the performance, durability, and safe operation of your vehicle,
note the following points regarding the
specified tires.
1
2
Tire air pressure
The tire air pressure should be checked
and, if necessary, adjusted before each
ride.
EWA10511
WARNING
Never overload your vehicle. Operation of an overloaded vehicle could
cause an accident.
Tire air pressure (measured on cold
tires):
Front:
200 kPa (2.00 kgf/cm2, 29 psi)
Rear:
250 kPa (2.50 kgf/cm2, 36 psi)
Maximum load*:
87 kg (192 lb)
* Total weight of rider, cargo and accessories
1. Tire tread depth
2. Tire sidewall
The tires must be checked before each
ride. If the center tread depth reaches
the specified limit, if the tire has a nail or
glass fragments in it, or if the sidewall is
cracked, have a Yamaha dealer replace the tire immediately.
Minimum tire tread depth (front and
rear):
1.6 mm (0.06 in)
TIP
The tire tread depth limits may differ
from country to country. Always comply
with the local regulations.
8-5
Tire information
This vehicle is equipped with cast
wheels and tube tires.
After extensive tests, only the tires listed below have been approved for this
model by Yamaha Motor Co., Ltd.
Front tire:
Size:
60/100-12 36J
Manufacturer/model:
INOUE RUBBER/MB80
Rear tire:
Size:
60/100-12 36J
Manufacturer/model:
INOUE RUBBER/MB80
EWA10471
WARNING
 Have a Yamaha dealer replace
excessively worn tires. Besides
being illegal, operating the vehicle with excessively worn tires
decreases riding stability and
can lead to loss of control.
 The replacement of all wheel
and brake-related parts, including the tires, should be left to a
Yamaha dealer, who has the
necessary professional knowl-
1CB-9-E0.book 6 ページ
2010年10月15日 金曜日 午前10時19分
PERIODIC MAINTENANCE AND ADJUSTMENT
edge and experience to do so.
 Ride at moderate speeds after
changing a tire since the tire
surface must first be “broken
in” for it to develop its optimal
characteristics.
EAU22002
Cast wheels
EWA10610
WARNING
The wheels on this model are not designed for use with tubeless tires.
Do not attempt to use tubeless tires
on this model.
To maximize the performance, durability, and safe operation of your vehicle,
note the following points regarding the
specified wheels.
 The wheel rims should be checked
for cracks, bends, warpage or
damage before each ride. If any
damage is found, have a Yamaha
dealer replace the wheel. Do not
attempt even the smallest repair to
the wheel. A deformed or cracked
wheel must be replaced.
 The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced. An
unbalanced wheel can result in
poor performance, adverse handling characteristics, and a shortened tire life.
8-6
EAU22152
Adjusting the front and rear
brake lever free play
The front and rear brake lever free play
should be measured at the positions as
shown.
2
Front
3
1
2
4
5
6
1. Front brake lever
7
2. Brake lever free play
8
9
1CB-9-E0.book 7 ページ
2010年10月15日 金曜日 午前10時19分
PERIODIC MAINTENANCE AND ADJUSTMENT
Front
Rear
dealer make this adjustment.
1
1
2
2
(a)
3
4
5
6
7
8
9
1
1. Rear brake lever
2. Brake lever free play
Front brake lever free play:
10.0–20.0 mm (0.39–0.79 in)
Rear brake lever free play:
10.0–20.0 mm (0.39–0.79 in)
Periodically check the front and rear
brake lever free play and, if necessary,
adjust them as follows.
To increase the brake lever free play,
turn the adjusting nut at the brake shoe
plate in direction (a). To decrease the
brake lever free play, turn the adjusting
nut in direction (b).
(b)
1. Front brake lever free play adjusting nut
Rear
(b)
1
(a)
1. Rear brake lever free play adjusting nut
EWA10650
WARNING
If proper adjustment cannot be obtained as described, have a Yamaha
8-7
1CB-9-E0.book 8 ページ
2010年10月15日 金曜日 午前10時19分
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU22361
Checking the front and rear
brake shoes
Front
2
1
The front and rear brake shoes must be
checked for wear at the intervals specified in the periodic maintenance and
lubrication chart. Each brake is provided with a wear indicator, which allows
you to check the brake shoe wear without having to disassemble the brake.
To check the brake shoe wear, check
the position of the wear indicator while
applying the brake. If a brake shoe has
worn to the point that the wear indicator
reaches the wear limit line, have a
Yamaha dealer replace the brake
shoes as a set.
1. Brake shoe wear indicator
2. Brake shoe wear limit line
Rear
EAU23095
Checking and lubricating the
cables
The operation of all control cables and
the condition of the cables should be
checked before each ride, and the cables and cable ends should be lubricated if necessary. If a cable is damaged
or does not move smoothly, have a
Yamaha dealer check or replace it.
WARNING! Damage to the outer
housing of cables may result in internal rusting and cause interference with cable movement. Replace
damaged cables as soon as possible to prevent unsafe conditions.[EWA10711]
Recommended lubricant:
Yamaha Chain and Cable Lube or
engine oil
2
3
4
5
6
7
8
9
2
1
1. Brake shoe wear indicator
2. Brake shoe wear limit line
8-8
1CB-9-E0.book 9 ページ
2010年10月15日 金曜日 午前10時19分
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU43631
Lubricating the front and rear
brake levers
1
Recommended lubricant:
Lithium-soap-based grease
EAU23192
Checking and lubricating the
centerstand
Front brake lever
2
3
4
5
6
The operation of the centerstand
should be checked before each ride,
and the pivots and metal-to-metal contact surfaces should be lubricated if
necessary.
Rear brake lever
7
EWA11301
WARNING
If the centerstand does not move up
and down smoothly, have a Yamaha
dealer check or repair it. Otherwise,
the centerstand could contact the
ground and distract the operator, resulting in a possible loss of control.
8
9
The pivoting points of the front and rear
brake levers must be lubricated at the
intervals specified in the periodic maintenance and lubrication chart.
Recommended lubricant:
Lithium-soap-based grease
8-9
1CB-9-E0.book 10 ページ
2010年10月15日 金曜日 午前10時19分
PERIODIC MAINTENANCE AND ADJUSTMENT
Checking the front fork
EAU42081
Checking the steering
The condition and operation of the front
fork must be checked as follows at the
intervals specified in the periodic maintenance and lubrication chart.
To check the condition
Check the inner tubes for scratches
and damage.
To check the operation
1. Place the vehicle on a level surface and hold it in an upright position. WARNING! To avoid injury,
securely support the vehicle so
there is no danger of it falling
over.[EWA10751]
2. While applying the front brake,
push down hard on the handlebars
several times to check if the front
fork compresses and rebounds
smoothly.
ECA10590
NOTICE
If any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or repair it.
EAU45511
Worn or loose steering bearings may
cause danger. Therefore, the operation
of the steering must be checked as follows at the intervals specified in the periodic maintenance and lubrication
chart.
1. Place the vehicle on the centerstand. WARNING! To avoid injury, securely support the vehicle
so there is no danger of it falling
over.[EWA10751]
2. Hold the lower ends of the front
fork legs and try to move them forward and backward. If any free
play can be felt, have a Yamaha
dealer check or repair the steering.
2
3
4
5
6
7
8
9
8-10
1CB-9-E0.book 11 ページ
2010年10月15日 金曜日 午前10時19分
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU23291
Checking the wheel bearings
ECA10650
2
3
4
6
7
8
9
Replacing the headlight bulb
This model is equipped with a halogen
bulb headlight. If the headlight bulb
burns out, replace it as follows.
1
5
EAU23797
The front and rear wheel bearings must
be checked at the intervals specified in
the periodic maintenance and lubrication chart. If there is play in the wheel
hub or if the wheel does not turn
smoothly, have a Yamaha dealer check
the wheel bearings.
NOTICE
Take care not to damage the following parts:
 Headlight bulb
Do not touch the glass part of
the headlight bulb to keep it free
from oil, otherwise the transparency of the glass, the luminosity
of the bulb, and the bulb life will
be adversely affected. Thoroughly clean off any dirt and fingerprints on the headlight bulb
using a cloth moistened with alcohol or thinner.
 Headlight lens
Do not affix any type of tinted
film or stickers to the headlight
lens.
Do not use a headlight bulb of a
wattage higher than specified.
8-11
1. Do not touch the glass part of the bulb.
1. Remove the headlight unit by removing the screws.
1
1. Screw
1CB-9-E0.book 12 ページ
2010年10月15日 金曜日 午前10時19分
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU24133
1
Replacing the tail/brake light
bulb
1. Remove the tail/brake light lens by
removing the screws.
2
1
1
3
1. Screw
1. Headlight bulb holder
2. Disconnect the headlight coupler,
and then remove the bulb cover.
1
2
4. Place a new headlight bulb into position, and then secure it with the
bulb holder.
5. Install the headlight bulb cover,
and then connect the coupler.
6. Install the headlight unit by installing the screws.
7. Have a Yamaha dealer adjust the
headlight beam if necessary.
4
2
1. Tail/brake light lens
5
6
2. Screw
2. Remove the burnt-out bulb by
pushing it in and turning it counterclockwise.
7
8
9
1. Headlight coupler
2. Headlight bulb cover
3. Unhook the headlight bulb holder,
and then remove the burnt-out
bulb.
8-12
1CB-9-E0.book 13 ページ
2010年10月15日 金曜日 午前10時19分
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU24204
Replacing a turn signal light
bulb
1
1
1. Remove the turn signal light lens
by removing the screw.
2
1
1
3
4
5
6
7
8
1. Tail/brake light bulb
3. Insert a new bulb into the socket,
push it in, and then turn it clockwise until it stops.
4. Install the lens by installing the
screws. NOTICE: Do not overtighten the screws, otherwise
the lens may break.[ECA10681]
1. Turn signal light bulb
2
1. Turn signal light lens
2. Screw
2. Remove the burnt-out bulb by
pushing it in and turning it counterclockwise.
9
8-13
3. Insert a new bulb into the socket,
push it in, and then turn it clockwise until it stops.
4. Install the lens by installing the
screw. NOTICE: Do not overtighten the screw, otherwise the
lens may break.[ECA11191]
1CB-9-E0.book 14 ページ
2010年10月15日 金曜日 午前10時19分
PERIODIC MAINTENANCE AND ADJUSTMENT
 Replace the charging cord or
EAU50572
Checking the charging cord
and charging plug
charging plug if damaged. Otherwise, this could cause a fire,
electric shock or short circuit.
 Check that there is no damage to
the charging cord or charging plug,
and if problem is detected, have a
Yamaha dealer check the vehicle.
 Check that there is no dirt or foreign material on the charging cord
or charging plug. Wipe off any dirt
with a dry cloth.
ECA17101
NOTICE
Make sure that corrosion inhibitors,
solvents or oil do not come in contact with the charging cord or charging plug while checking the vehicle.
1
1. Crack
1
2
3
4
5
6
7
1
8
1. Tear
1. Bend
EWA15790
WARNING
 Do not check or repair the vehicle with the charging plug
plugged in to the outlet. This
could cause an electric shock or
short circuit.
8-14
9
1CB-9-E0.book 15 ページ
2010年10月15日 金曜日 午前10時19分
PERIODIC MAINTENANCE AND ADJUSTMENT
Troubleshooting
1
2
3
4
5
6
7
8
9
EAU50182
If a problem occurs, check the following
before taking the vehicle to a Yamaha
dealer. However, if no electric power is
supplied (nothing appears in the display), have a Yamaha dealer check the
vehicle.
The vehicle does not enter the
standby mode when the key is
turned to “ON”
Check the following:
1. Is the vehicle currently being
charged?
The vehicle does not enter the
standby mode when the key is
turned to “ON” during charging.
2. Was the key turned to “ON” while
the accelerator grip was being
opened?
If the key is turned to “ON” while
the accelerator grip is opened, the
vehicle does not enter the standby
mode. Close the accelerator grip,
turn the key to “OFF” and then
back to “ON”.
If the vehicle still fails to enter the standby mode, have a Yamaha dealer check
the vehicle.
The vehicle does not start off
Is the vehicle in the riding mode? (Does
the operating status indicator “RUN”
appear in the display?)
The vehicle cannot be ridden unless it
is in the riding mode.
After checking the above, try starting off
again by following the procedures described on page 7-1 “Preparations for
starting off” and page 7-3 “Starting off”
to restart the vehicle.
If the vehicle still does not start off, have
a Yamaha dealer check it.
The warning mark “
” appears
Turn the key to “OFF” and then back to
“ON”. If the warning mark “
” still appears, have a Yamaha dealer check
the vehicle.
TIP
Although the warning mark appears,
the vehicle can still be ridden if the operating status indicator “RUN” appears
and the vehicle is in the riding mode.
8-15
A light does not come on
Check the following:
1. Is the vehicle currently being
charged? Lights do not come on if
the vehicle is being charged.
2. Is the key turned to “ON”? (Does
anything appear in the display?)
If nothing appears in the display,
the auto-off function may be activated. Turn the key to “OFF” and
then back to “ON”.
3. Are all switches working properly?
After checking the above, and a light
does still not come on, proceed with the
following.
 If the headlight fails to come on,
the bulb may be burned out. Refer
to page 8-11 for replacement procedures.
 If a tail/brake light or turn signal
light fails to come on, a bulb may
be burned out. Refer to page 8-12
or 8-13 for replacement procedures.
If a light still does not come on, a fuse
may be blown. Have a Yamaha dealer
check the vehicle.
1CB-9-E0.book 16 ページ
2010年10月15日 金曜日 午前10時19分
PERIODIC MAINTENANCE AND ADJUSTMENT
ECA11981
NOTICE
Do not use a bulb of a wattage other
than specified to avoid causing extensive damage to the electrical system and possibly a fire.
The motor stops while riding
Check the following:
1. Is the battery sufficiently charged?
Check the battery level indicator. If
the remaining charge is insufficient, charge the battery before
continuing to ride.
2. Is “HEAT” flashing and did “RUN”
go off?
1
1. Temperature indicator “HEAT”
The temperature protection func-
tion has been activated. Turn the
key to “OFF”, and allow the vehicle
to cool down before continuing to
ride.
After checking the above, if the motor
still does not run, have a Yamaha dealer check the vehicle.
cient, charge the battery before
continuing to ride.
After checking the above, turn the key
to “ON” again. If the display and headlight do not come on, have a Yamaha
dealer check the vehicle.
EWA15630
WARNING
Before pushing or moving the
EC-03, be sure to turn the key to
“OFF”. The vehicle may suddenly
start to move if the accelerator grip
is turned while the key is turned to
“ON”.
WARNING
Before pushing or moving the
EC-03, be sure to turn the key to
“OFF”. The vehicle may suddenly
start to move if the accelerator grip
is turned while the key is turned to
“ON”.
The display and headlight go off
when the key is turned to “ON”
Check the following:
1. Has the vehicle been stopped for
more than five minutes?
To protect the battery, the EC-03 is
equipped with an auto-off function.
If the vehicle has been stopped for
more than five minutes, the power
is cut to save the battery charge.
2. Is the battery sufficiently charged?
If the remaining charge is insuffi8-16
EWA15630
The security lock cannot be unlocked
If an incorrect security number is entered three times in succession, the security lock cannot be unlocked even if
the correct security number is entered
after that.
Turn the key to “OFF” and then back to
“ON”, then try entering the correct security number again.
2
3
4
5
6
7
8
9
1CB-9-E0.book 17 ページ
2010年10月15日 金曜日 午前10時19分
PERIODIC MAINTENANCE AND ADJUSTMENT
1
The warning light comes on, and
“CHG” and the warning mark “
”
flash during charging
utes. If charging automatically stops
again, there may be a malfunction with
the vehicle. Stop charging and have a
Yamaha dealer check the vehicle.
When the key is turned to “ON”, the
warning light comes on and both
“CHG” and the warning mark “
”
flash in the display
2
3
there may be a malfunction with the vehicle. Have a Yamaha dealer check the
vehicle.
“– – – – –” flashes in the display
during charging
4
5
1
2
3
1. Warning light
6
7
8
9
1
2. Battery condition indicator “CHG”
3. Warning mark “
”
If a problem occurs during charging, the
charging automatically stops. The
warning light comes on and both “CHG”
and the warning mark “
” flash.
TIP
If this continues for five minutes, the
warning light goes off, along with all indicators in the display.
Unplug the charging plug from the outlet to stop charging, and then start
charging again after waiting a few min-
1. Charging error indicator “– – – – –”
1
2
3
1. Warning light
2. Battery condition indicator “CHG”
3. Warning mark “
”
The battery is not charged properly.
Turn the key “OFF” and then back to
“ON” in order to reset charging. Turn
the key to “OFF” and then charge the
battery again.
After charging, if the above still occurs,
8-17
If the battery voltage is below the specified level, the display shows this indicator. Continue charging.
If the warning light comes on and both
“CHG” and “
” flash in the display after charging for one hour, there may be
a malfunction with the vehicle. Have a
Yamaha dealer check the vehicle.
1CB-9-E0.book 18 ページ
2010年10月15日 金曜日 午前10時19分
PERIODIC MAINTENANCE AND ADJUSTMENT
The charging process is in the standby
mode because the battery temperature
is higher than 50 C. Allow the battery
to cool down.
When the battery temperature falls to
the specified temperature, “HEAT”
goes off and charging starts automatically. (See page 6-1 for more information about “Battery charging place”.)
1
2
3
“COOL” flashes in the display during charging
1. Warning light
2. Battery condition indicator “CHG”
3. Warning mark “
”
“HEAT” flashes in the display during charging
warm place.
When the battery temperature reaches
the specified temperature, “COOL”
goes off and charging starts automatically. (See page 6-1 for more information about “Battery charging place”.)
When the key is turned to “ON”, the
beeper sounds and the following
occurs
 The warning light flashes
 The warning mark “
” comes on
 The battery level indicator segments move from side to side
 “PUSH” indicator and “OLD” indicator alternately appear
2
3
4
5
6
7
8
1
1. Temperature indicator “COOL”
1
1. Temperature indicator “HEAT”
This is not a malfunction.
This is not a malfunction.
The charging process is in the standby
mode because the battery temperature
is lower than –5 C.
If this occurs, start recharging in a
8-18
9
1CB-9-E0.book 19 ページ
2010年10月15日 金曜日 午前10時19分
PERIODIC MAINTENANCE AND ADJUSTMENT
When charging is started, the beeper sounds, and the following indicates the battery is at the end of its
service life
 The warning light flashes
 The warning mark “
” comes on
 The “PUSH” indicator and “OLD”
indicator alternately appear in the
display
1
2
3
4
1
2
3
4
1. Battery level indicator
2. Warning light
5
3. Battery condition indicator “PUSH”/“OLD”
6
The battery is near the end of its service life.
Push one of the control buttons (See
page 4-3.) to cancel the beeper. This
switches the vehicle to the standby
mode.
7
8
9
4. Warning mark “
”
Cancel the standby mode by pushing a
control button again.
Although the vehicle can still be ridden
if the operating status indicator “RUN”
appears, the battery is near the end of
its service life. Consult a Yamaha dealer as soon as possible to order a replacement battery.
TIP
If a control button is pushed, the beeper
stops and the display changes to the
standby mode. If no control button is
pushed within five minutes, the auto-off
function is activated, and all power is
cut to protect the battery.
8-19
1
2
3
1. Warning light
2. Battery condition indicator “PUSH”/“OLD”
3. Warning mark “
”
The battery has reached the end of its
service life.
Have a Yamaha dealer replace the battery. Push one of the control buttons
(See page 4-3.) to cancel the beeper.
This display switches to the following
1CB-9-E0.book 20 ページ
2010年10月15日 金曜日 午前10時19分
PERIODIC MAINTENANCE AND ADJUSTMENT
indicating the battery has reached the
end of its service life.
1
2
1. Warning light
2. End of battery service life indicator “End”
Unplug the charging plug, and all indicators in the display go off.
TIP
 The beeper continues to sound
and “End” is displayed to indicate
the end of the battery service life
until one of the buttons are
pushed.
 To protect the battery, the EC-03 is
equipped with an auto-off function.
After five minutes have passed,
the power goes off, the beeper
stops and the display goes off.
The battery cannot be charged (the
battery level indicator remains low
after charging)
Is the charging plug properly plugged
into an outlet?
After checking, charge the battery
again by the procedures described in
“Charging procedure” on page 6-3.
If the battery still cannot be charged after checking the above, there could be
a malfunction in the battery charger.
Have a Yamaha dealer check the vehicle.
Unusual odor or smoke emerges
from the battery charger
Unplug the charging plug from the outlet immediately. Have a Yamaha dealer
check the vehicle.
The riding distance of a single
charge has become significantly
shorter
The battery has reached the end of its
service life.
Have a Yamaha dealer replace the battery.
8-20
The battery cannot be charged because the residual-current device
(RCD) protection has been activated
Stop charging and have a Yamaha
dealer check the vehicle.
2
3
4
5
6
7
8
9
1CB-9-E0.book 1 ページ
2010年10月15日 金曜日 午前10時19分
SCOOTER CARE AND STORAGE
Matte color caution
EAU37833
ECA15192
1
2
3
4
5
6
7
8
9
NOTICE
Some models are equipped with
matte colored finished parts. Be
sure to consult a Yamaha dealer for
advice on what products to use before cleaning the vehicle. Using a
brush, harsh chemical products or
cleaning compounds when cleaning
these parts will scratch or damage
their surface. Wax also should not
be applied to any matte colored finished parts.
EAU50831
Care
Cleaning
EWA15810
While the open design of a scooter reveals the attractiveness of the technology, it also makes it more vulnerable.
Rust and corrosion can develop even if
high-quality components are used. Frequent and proper care does not only
comply with the terms of the warranty,
but it will also keep your scooter looking
good, extend its life and optimize its
performance.
Before cleaning
1. Make sure that the seat is properly
closed before cleaning.
2. Make sure that all caps and covers
as well as all electrical couplers
and connectors, are tightly installed.
3. Remove extremely stubborn dirt,
with a degreasing agent and a
brush, but never apply such products onto seals, gaskets and wheel
axles. Always rinse the dirt and degreaser off with water.
9-1
WARNING
 Do not wash the vehicle while
charging the battery. This could
cause a fire or electric shock.
 Make sure that the seat is properly closed before washing. If
the seat is not properly closed,
water could splash on the battery or built-in charger. This
could cause an electric shock or
short circuit.
 Do not wash the charging cord
and charging plug. Wipe clean
with a dry rag.
ECA17121
NOTICE
 Avoid using strong acidic wheel
cleaners, especially on spoked
wheels. If such products are
used on hard-to-remove dirt, do
not leave the cleaner on the affected area any longer than instructed. Also, thoroughly rinse
the area off with water, immediately dry it, and then apply a corrosion protection spray.
1CB-9-E0.book 2 ページ
2010年10月15日 金曜日 午前10時19分
SCOOTER CARE AND STORAGE
 Improper cleaning can damage
plastic parts (such as cowlings,
panels, windshields, headlight
lenses, meter lenses, etc.) and
the mufflers. Use only a soft,
clean cloth or sponge with water to clean plastic. However, if
the plastic parts cannot be thoroughly cleaned with water, diluted mild detergent with water
may be used. Be sure to rinse
off any detergent residue using
plenty of water, as it is harmful
to plastic parts.
 Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, gasoline, rust removers
or inhibitors, brake fluid, antifreeze or electrolyte.
 Do not use high-pressure washers or steam-jet cleaners since
they cause water seepage and
deterioration in the following areas: seals (of wheel and swingarm bearings, fork and brakes),
electric components (couplers,
connectors, instruments, accelerator grip, switches and lights),
breather hoses and vents.
 For scooters equipped with a
windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning compounds for plastic may leave
scratches on the windshield.
Test the product on a small hidden part of the windshield to
make sure that it does not leave
any marks. If the windshield is
scratched, use a quality plastic
polishing
compound
after
washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
9-2
After riding in the rain, near the sea or
on salt-sprayed roads
Since sea salt or salt sprayed on the
roads during winter are extremely corrosive in combination with water, carry
out the following steps after each ride in
the rain, near the sea or on
salt-sprayed roads.
TIP
Salt sprayed on roads in the winter may
remain well into spring.
1. Clean the scooter with cold water
and a mild detergent after the motor has cooled down. NOTICE: Do
not use warm water since it increases the corrosive action of
the salt.[ECA10791]
2. Apply a corrosion protection spray
on all metal, including chrome- and
nickel-plated, surfaces to prevent
corrosion.
After cleaning
1. Dry the scooter with a chamois or
an absorbing cloth.
2. Use a chrome polish to shine
chrome, aluminum and stainless-steel parts.
2
3
4
5
6
7
8
9
1CB-9-E0.book 3 ページ
2010年10月15日 金曜日 午前10時19分
SCOOTER CARE AND STORAGE
1
2
3
4
5
6
7
8
9
3. To prevent corrosion, it is recommended to apply a corrosion protection spray on all metal,
including chrome- and nickel-plated, surfaces.
4. Use spray oil as a universal cleaner to remove any remaining dirt.
5. Touch up minor paint damage
caused by stones, etc.
6. Wax all painted surfaces.
7. Let the scooter dry completely before storing or covering it.
EWA15820
WARNING
Contaminants on the brakes or tires
can cause loss of control.
 Make sure that there is no oil or
wax on the brakes or tires. If
necessary, wash the tires with
warm water and a mild detergent.
 Before operating the scooter,
test its braking performance
and cornering behavior.
any excess.
 Never apply oil or wax to any
rubber and plastic parts, but
treat them with a suitable care
product.
 Avoid using abrasive polishing
compounds as they will wear
away the paint.
Storage
EAU50842
Short-term
Always store your scooter in a cool, dry
place and, if necessary, protect it
against dust with a porous cover. Be
sure the motor is cool before covering
the scooter.
TIP
ECA17130
 Consult a Yamaha dealer for ad-
vice on what products to use.
 Washing, rainy weather or humid
climates can cause the headlight
lens to fog. Turning the headlight
on for a short period of time will
help remove the moisture from the
lens.
NOTICE
 Storing the scooter in a poorly
ventilated room or covering it
with a tarp while it is still wet,
will allow water and humidity to
seep in and cause rust, power
unit failure, electric leakage, or
short-circuiting.
 To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemicals are stored.
Long-term
ECA10800
ECA17142
NOTICE
 Apply spray oil and wax sparingly and make sure to wipe off
NOTICE
 Charge the battery if the level
drops to the last segment. In or9-3
1CB-9-E0.book 4 ページ
2010年10月15日 金曜日 午前10時19分
SCOOTER CARE AND STORAGE
der to extend the battery life, it is
recommended to charge the
battery until the battery level indicator reaches a maximum of
2–3 segments. A lower or higher
charge is not recommended.
 Make sure that the amount of
charge remaining in the battery
does not fall below 20% (less
than the last segment of the battery level indicator). If stored under this condition for a long
period of time, the battery can
be damaged and may need to be
replaced depending on how low
the capacity is.
 Once the battery is completely
depleted, it cannot be recharged.
 After long-term storage, be sure
to recharge the battery before
using the vehicle. (It may take
longer to charge than usual.)
pivoting points of all levers as well
as the centerstand.
3. Check and, if necessary, correct
the tire air pressure, and then lift
the scooter so that both of its
wheels are off the ground. Alternatively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.
TIP
Make any necessary repairs before
storing the scooter.
2
3
4
5
6
7
8
9
Before storing your scooter for several
months:
1. Follow all the instructions in the
“Care” section of this chapter.
2. Lubricate all control cables and the
9-4
1CB-9-E0.book 1 ページ
2010年10月15日 金曜日 午前10時19分
SPECIFICATIONS
Dimensions:
1
2
3
4
5
6
7
8
9
10
Overall length:
1565 mm (61.6 in)
Overall width:
600 mm (23.6 in)
Overall height:
990 mm (39.0 in)
Seat height:
745 mm (29.3 in)
Wheelbase:
1080 mm (42.5 in)
Ground clearance:
110 mm (4.33 in)
Minimum turning radius:
1700 mm (66.9 in)
Weight:
Curb weight:
56 kg (123 lb)
Chassis:
Frame type:
Backbone
Caster angle:
25.00 
Trail:
75 mm (3.0 in)
Front tire:
Type:
With tube
Size:
60/100-12 36J
Manufacturer/model:
INOUE RUBBER/MB80
EAU50970
Rear tire:
Front suspension:
Type:
With tube
Size:
60/100-12 36J
Manufacturer/model:
INOUE RUBBER/MB80
Maximum load:
87 kg (192 lb)
* (Total weight of rider, cargo and accessories)
Tire air pressure (measured on cold
tires):
Front:
200 kPa (2.00 kgf/cm2, 29 psi)
Rear:
250 kPa (2.50 kgf/cm2, 36 psi)
Front wheel:
Rim size:
12 x 1.50
Rear wheel:
Rim size:
12 x 1.50
Front brake:
Type:
Drum brake
Operation:
Right hand operation
Rear brake:
Type:
Drum brake
Operation:
Left hand operation
10-1
Type:
Telescopic fork
Spring/shock absorber type:
Coil spring
Wheel travel:
50.0 mm (1.97 in)
Rear suspension:
Type:
Unit swing
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
55.0 mm (2.17 in)
Headlight:
Bulb type:
Halogen bulb
Bulb voltage, wattage  quantity:
Headlight:
12 V, 35 W/35 W  1
Tail/brake light:
12 V, 5.0 W/21.0 W  1
Front turn signal light:
12 V, 10.0 W  2
Rear turn signal light:
12 V, 10.0 W  2
Warning indicator light:
LED
1CB-9-E0.book 1 ページ
2010年10月15日 金曜日 午前10時19分
CONSUMER INFORMATION
Identification numbers
EAU48611
EAU26400
Vehicle identification number
Record the vehicle identification number and model label information in the
spaces provided below for assistance
when ordering spare parts from a
Yamaha dealer or for reference in case
the vehicle is stolen.
VEHICLE IDENTIFICATION
NUMBER:
EAU26540
Model label
1
1
2
3
4
1. Vehicle identification number
MODEL LABEL INFORMATION:
The vehicle identification number is
stamped into the steering head pipe.
Record this number in the space provided.
TIP
The vehicle identification number is
used to identify your motorcycle and
may be used to register your motorcycle with the licensing authority in your
area.
1. Model label
The model label is affixed to the frame
under the seat. (See page 4-12.)
Record the information on this label in
the space provided. This information
will be needed when ordering spare
parts from a Yamaha dealer.
5
6
7
8
9
10
11
11-1
1CB-9-E0.book 2 ページ
2010年10月15日 金曜日 午前10時19分
INDEX
A
Acceleration and deceleration....................7-4
Accelerator grip, checking..........................8-4
B
Battery, charging location ..........................6-1
Battery, charging procedure.......................6-3
Battery, charging safely .............................1-5
Battery, charging time ................................6-8
Battery, effective use of .............................3-3
Battery level ...............................................3-4
Battery type, about.....................................6-9
Beeper .......................................................4-1
Brake lever, front......................................4-11
Brake lever, rear ......................................4-11
Brake levers, lubricating.............................8-9
Brake shoes, checking...............................8-8
Braking.......................................................7-5
Grab bar...................................................4-13
Handlebar switches..................................4-11
Headlight bulb, replacing .........................8-11
Helmet holder...........................................4-12
W
Vehicle identification number .................. 11-1
M
Main switch/steering lock........................... 4-1
Maintenance and lubrication, periodic ....... 8-2
Matte color, caution ................................... 9-1
Model label .............................................. 11-1
Motor, checking for irregular sounds ......... 8-4
Multi-function display ................................. 4-2
P
Parking ...................................................... 7-5
Part locations............................................. 2-1
S
Safe-riding points....................................... 1-4
Safety information...................................... 1-1
Seat ......................................................... 4-12
Security lock, using.................................... 4-7
Specifications .......................................... 10-1
Standard mode/power mode ..................... 3-1
Starting off ................................................. 7-3
Starting off, preparations ........................... 7-1
Steering, checking ................................... 8-10
Storage ...................................................... 9-3
F
H
Identification numbers ............................. 11-1
Luggage hook.......................................... 4-13
Cables, checking and lubricating ...............8-8
Care ...........................................................9-1
Centerstand, checking and lubricating.......8-9
Charging cord and plug, checking ...........8-14
Charging display, progress status..............6-9
G
V
L
C
Features.....................................................3-1
Front and rear brake lever free play,
adjusting ..................................................8-6
Front fork, checking .................................8-10
Horn switch.............................................. 4-11
I
T
Tail/brake light bulb, replacing................. 8-12
Tires........................................................... 8-5
Traveling distance ..................................... 3-2
Troubleshooting....................................... 8-15
Turn signal light bulb, replacing............... 8-13
Turn signal switch.................................... 4-11
Wheel bearings, checking ....................... 8-11
Wheels ...................................................... 8-6
✤✰✯✲✣❉❖
❉❊ ✦ ✤✰✯✲✣❉❖
❉❊ ✧ YAMAHA MOTOR CO., LTD.
PRINTED ON RECYCLED PAPER
PRINTED IN JAPAN
2010.10–0.0×1 !
(E)