Samsung SPL4225 Operating instructions

Owner’s Instructions
SPL4225
Samsung Electronics America inc.
105 Challenger Road, Ridgefield Park, N.J. 07660-0511, U.S.A
SERVICE DIVISION
TEL: 1-800-SAMSUNG (1-800-726-7864)
www.samsungsupport.com
BN68-00262A-01(ENG)
Warning! Important Safety Instructions
Thank You for Choosing Samsung
Thank you for choosing Samsung! Your new Samsung product represents the latest in television technology. We designed it with easy-to-use on-screen menus and closed captioning capabilities, making it
one of the best products in its class. We are proud to offer you a product that will provide convenient,
dependable service and enjoyment for years to come.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact
with any inside part of this product.
Important Safety Information
Always be careful when using your Monitor. To reduce the risk of fire, electrical shock, and other
injuries, keep these safety precautions in mind when installing, using, and
maintaining your machine.
• Read all safety and operating instructions before operating your Monitor.
• Keep the safety and operating instructions for future reference.
This symbol alerts you that important literature concerning operation and maintenance has been
included with this product.
• Heed all warnings on the Monitor and in the operating instructions.
• Follow all operating and use instructions.
Note to CATV system installer: This reminder is provided to call CATV system installer's attention to Article 820-40 of the National Electrical Code (Section 54 of Canadian Electrical Code, Part I), that provides
guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the
grounding system of the building as close to the point of cable entry as practical.
• Unplug the Monitor from the wall outlet before cleaning. Use a damp cloth; do not use liquid or
aerosol cleaners.
• Never add any attachments and/or equipment without approval of the manufacturer. Such additions
can increase the risk of fire, electric shock, or other personal injury.
Caution: FCC/CSA regulations state that any unauthorized changes or modifications to this equipment may
void the user's authority to operate it.
• Do not use the Monitor where contact with or immersion in water is a possibility, such as near bath
tubs, sinks, washing machines, swimming pools, etc.
Caution: To prevent electric shock, match the wide blade of plug to the wide slot, and fully insert the plug.
• Do not place the Monitor on an unstable cart, stand, tripod, bracket,
table, or floor where it can fall. A falling Monitor can cause serious
injury to a child or adult, and serious damage to the appliance. Use
only with a cart, stand, tripod, bracket, or table recommended by the
manufacturer or sold with the Monitor. Follow the manufacturer's
instructions when mounting the unit, and use a mounting accessory
recommended by the manufacturer. Move the Monitor and cart with
care. Quick stops, excessive force, and uneven surfaces can make the
unit and cart unsteady and likely to overturn.
Attention: pour eviter les chocs electriques, introduire la lame le plus large de la fiche dans la borne correspondante de la prise et pousser jusqu'au fond.
Important: One Federal Court has held that unauthorized recording of copyrighted TV programs is an
infringement of U.S. copyright laws.
Certain Canadian programs may also be copyrighted and any unauthorized recording in whole or in part
may be in violation of these rights.
TO PREVENT DAMAGE WHICH MAY RESULT IN FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
• Provide ventilation for the Monitor. The unit is designed with slots in the cabinet for ventilation to protect it from overheating. Do not block these openings with any object, and do not place the Monitor
on a bed, sofa, rug, or other similar surface. Do not place it near a radiator or heat register. If you
place the Monitor on a rack or bookcase, ensure that there is adequate ventilation and that you've
followed the manufacturer's instructions for mounting.
• Operate your Monitor only from the type of power source indicated on the marking label. If you are
not sure of the type of power supplied to your home, consult your appliance dealer or local power
company.
• Use only a grounded or polarized outlet. For your safety, this Monitor is equipped with a polarized
alternating current line plug having one blade wider than the other. This plug will fit into the power
outlet only one way. If you are unable to insert the plug fully into the outlet, try reversing the plug. If
the plug still does not fit, contact your electrician to replace your outlet.
2
3
FCC Information
• Protect the power cord. Power supply cords should be routed so that they won’t be walked on or pinched
by objects placed on or against them. Pay particular attention to cords at plugs, convenience receptacles, and the point where they exit from the unit.
• Unplug the Monitor from the wall outlet and disconnect the antenna or cable system during a lightning
storm or when left unattended and unused for long periods of time. This will prevent damage to the unit
due to lightning and power-line surges.
• Avoid overhead power lines. An outside antenna system should not be placed in the vicinity of overhead
power lines or other electric light or power circuits or where it can fall into such power lines or circuits.
When installing an outside antenna system, be extremely careful to keep from touching the power lines
or circuits. Contact with such lines can be fatal.
• Do not overload the wall outlet or extension cords. Overloading can result in fire or electric shock.
• Do not insert anything through the openings in the unit, where they can touch dangerous voltage points
or damage parts. Never spill liquid of any kind on the Monitor.
• Ground outdoor antennas. If an outside antenna or cable system is connected to the Monitor, be sure the
antenna or cable system is grounded so as to provide some protection against voltage surges and builtup static charges. Section 810 of the National Electrical Code, ANSI/NFPA No.70-1984, provides information about proper grounding of the mast and supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to
grounding electrodes, and requirements for the grounding electrode.
The Federal Communications Commission Radio
Frequency Interference Statement includes the following warning:
NOTE: This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures.
User Information
• Do not attempt to service the Monitor yourself. Refer all servicing to qualified service personnel. Unplug
the unit from the wall outlet and refer servicing to qualified service personnel under the following conditions:
- when the power-supply cord or plug is damaged
- if liquid has been spilled on the unit or if objects have fallen into the unit
- if the Monitor has been exposed to rain or water
- if the Monitor does not operate normally by following the operating instructions
- if the Monitor has been dropped or the cabinet has been damaged
- when the Monitor exhibits a distinct change in performance
Changes or modifications not expressly approved
by the party responsible for compliance could
void the user’s authority to operate the equipment.
If necessary, consult your dealer or an experienced radio/television technician for additional
suggestions. You may find the booklet called How
to Identify and Resolve Radio/TV Interference
Problems helpful. This booklet was prepared by
the Federal Communications Commission. It is
available from the U.S. Government Printing
Office, Washington, DC 20402, Stock Number
004-000-00345-4 .
• If you make adjustments yourself, adjust only those controls that are covered by the operating instructions. Adjusting other controls may result in damage and will often require extensive work by a qualified
technician to restore the Monitor to normal.
Warning
• When replacement parts are required, be sure the service technician uses replacement parts specified by
the manufacturer or those that have the same characteristics as the original part. Unauthorized substitutions may result in additional damage to the unit.
• Upon completion of any service or repairs to this Monitor, ask the service technician to perform safety
checks to determine that the Monitor is in a safe operating condition.
• The PDP can properly operate within the temperature range of 32~104˚F and humidity 80%.
Do not use in a hot and humid place. within the temperature range of
• Before moving the PDP equipped with speakers, separate the speakers from the PDP.
If you move the PDP holding the speakers, it may result in a detachment of the PDP and cause any
damage to the PDP and other personal injury.
4
User Instructions
This is a Class B product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
User must use shielded signal interface cables to
maintain FCC compliance for the product.
Declaration of conformity for products marked
with FCC Logo. This device complies with Part 15
of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and
(2) this device must accept any interference
received, including interference that may
cause undesired operation.
The party responsible for product compliance:
SAMSUNG ELECTRONICS CO., LTD
America QA Lab of Samsung
3351 Michelson Drive, Suite #290,
Irvine, CA 92612, U.S.A
Tel) 949-975-7310
Fax) 949-975-7328
Provided with this monitor is a detachable power
supply cord with IEC320 style terminations.
It may be suitable for connection to any UL Listed
personal computer with similar configuration.
Before making the connection, make sure the voltage rating of the computer convenience outlet is
the same as the monitor and that the ampere rating of the computer convenience outlet is equal to
or exceeds the monitor voltage rating.
For 110 Volt applications, use only UL Listed
detachable power cord with NEMA configuration
5-15P type (parallel blades) plug cap. For 230
Volt applications use only UL Listed Detachable
power supply cord with NEMA configuration
6015P type (tandem blades) plug cap.
IC Compliance Notice
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations of ICES-003.
Notice de Conformité IC
Cet appareil numérique de Classe B respecte
toutes les exigences du Règlement ICES-003 sur
les équipements produisant des interférences au
Canada.
European Notice
Products with the CE Marking comply with both
the EMC Directive (89/336/EEC), (92/31/EEC),
(93/68/EEC) and the Low Voltage Directive
(73/23/EEC) issued by the Commission of the
European Community. Compliance with these
directives implies conformity to the following European Norms:
• EN55022 : 1998 Class B
• EN55024 : 1998
• EN61000-3-2 : 1995
• EN61000-3-3 : 1995
5
User Instructions
Screen Image retention
Do not display a still image (such as on a video game or when hooking up a PC to this Monitor) on the
plasma monitor panel for more than several minutes as it can cause screen image retention. This image
retention is also known as “screen burn”. To avoid such image retention, refer to page 28 of this manual to
reduce the degree of brightness and contrast of this screen when displaying a still image.
Cell Defect
The plasma display panel consists of fine cells. Although the panels are produced with more than 99.9
percent active cells, there may be some cells that do not produce light or remain lit.
Table of Contents
Setup
Connecting PC and Operation
Your New Plasma Display Panel ........................10
Connecting to a PC..........................................46
Remote Control Buttons ....................................12
Adjusting the PC Screen ..................................50
Wall Installation Instructions ..............................14
Changing the Position of the Image....................51
Turning the PDP On and Off..............................18
Changing the Size of the Image ........................52
Enlarging the Image (Zoom) ..............................53
Connection (Connecting Speakers /
Receiver)
Altitude
Connecting Speakers ......................................22
The PDP will not operate normally at altitudes above 6500 ft.
Connecting a VCR/Cable Box ..........................23
Warranty
Warranty Period: One year starting from the purchase of your Monitor.
Warranty does not cover any damage caused by image retention.
Moving the Zoom Picture ..................................54
Picture Quality Adjustment ................................55
Information ....................................................58
Power Saver (PC mode only) ............................59
Connecting a DVD ..........................................24
Connecting a Set-Top Box ................................25
Picture Control
Customizing the Picture ....................................28
Using Automatic Picture Settings ........................29
Function Description
Selecting a Menu Language..............................62
Setting the Multi Control ..................................63
Using the Key Lock ..........................................64
Setting up Your Remote Control ........................65
Viewing the Picture-in-Picture ............................30
Changing the Screen Size ................................33
Freezing the Picture..........................................34
Sound Control
Appendix
Troubleshooting ..............................................68
Care and Maintenance ....................................69
Specifications..................................................70
Customizing the Sound ....................................36
Using Automatic Sound Settings ........................37
Using the Surround ........................................38
Time Setting
Setting the Clock ............................................40
Setting the Sleep Timer ....................................41
Setting the Timers ............................................42
6
7
P
L
A
S
M
A
D
I
S
P
L
A
Y
P
A
N
E
L
Setup
Your New Plasma Display Panel ....................................................10
Remote Control Buttons ................................................................12
Wall Installation Instructions ..........................................................14
Turning the PDP On and Off ..........................................................18
Your New Plasma Display Panel
Front Panel
Rear Panel
Speakers
POWER
Press to turn
the PDP on
and off.
SOURCE, MENU, VOLUME (-,+),
SELECT (▼,▲), MUTE
Remote Control Signal Receiver
Aim the remote control towards
this spot on the Monitor.
Checking Accessories
ΠExternal Speaker Out jacks
ˆ S-Video Input jack
Connect external speakers.
Connect a S-Video signal from an S-VHS VCR
or DVD player.
´ PC(RGB) Input jack (15pin)
Connect to the video output jack on your PC.
ˇ Component Video Input jacks ( Y/P /P )
b
Remote Control/
AAA Batteries
PC Cable
Video/Audio Cables
Video Cable
r
Component 1 inputs are for 480i/480p.
Component 2 inputs are for 480p/720p/
1080i.
¨ Video Input jack
Connect a video signal from external sources
such as VCRs or DVD players.
Power Cord
10
S-VIDEO Cable
Ferrite Cores(2EA)
Ø Audio Input (Video/Component1/2/PC(RGB))
jacks
Connect a audio signal from external sources
such as VCRs, PC or DVD players.
∏ Service Jack
Connect the RS-232C input jack to your PC.
” Power Input jack
Connect the supplied power cord.
Owner’s Instructions
11
Remote Control Buttons
ı VCR control buttons
Remote Control
ΠPower button
Turns the PDP on and off.
´ Number buttons
ˇ Display button
Press to display information on the PDP screen.
¨ Menu button
Displays the main on-screen menu.
ˆ CH (Channel) and VOL (Volume) buttons
Channel and Volume buttons are used for selecting
menu items in the menu mode.
Ø Mute button
Press to mute the PDP sound.
∏ P.Mode button
Adjust the PDP picture by selecting one of the preset
factory settings (or select your personal, customized
picture settings.)
” Aspect button
Press to change the screen size.
Flip the cover open
in the arrow direction.
Controls VCR tape functions: Stop, Rewind,
Play/Pause, Fast Forward.
˜ SET button
S.Sel
Used during setup of this remote control, so that it will
work compatibly with other devices (VCR, cable box,
DVD, etc.)
¯ Clock set button
Press to set clock.
˘ PIP control buttons
Source : Press to select one of the available signal
sources for the PIP window.
S.Sel : Press to select the Audio (PIP or Main).
Locate : Press to move the PIP window on the screen.
¿ PC control buttons
Auto Adjust
Scaling
Zoom/Pan
¸ S.Mode button
Adjust the PDP sound by selecting one of the preset
factory settings (or select your personal, customized
sound settings.)
˛ Sleep button
Press to select a preset time interval for automatic
shutoff.
’ Mode button
Selects a target device to be controlled by the Samsung remote control (ie., VCR, Cable, or DVD players).
˝ Clock Display button
Installing the Batteries in Your Remote Control
Press to display clock on the PDP screen.
Ô Source button
Press to display all of the available video sources
(ie., Video, S-Video, Component1, Component2,
PC(RGB)).
 Joystick button
cover
1 toSlideopenthethebackbattery
compartment of the
remote control
Install two AAA size batterthe cover back into
2 ies.
3Slide
Make sure to match the
place.
“+” and “-” ends of the batteries with the diagram
inside the compartment.
Use to highlight on-screen menu items and change
menu values.
Ò Still button
Press to pause the current screen.
Ú PIP button
Activates picture in picture.
Æ Source selection buttons
Press to directly select Video, S-Video, Component1,
Component2 or PC(RGB).
12
Remote Control Operation Range.
You can use your remote control within a distance of 23 feet and an angle of 30 degrees
from the left and right sides of the remote control receiver of the monitor.
13
Wall Installation Instructions
Installation Notes
1
2
Installing the Display on the Wall Attachment Panel
Do not install the PDP in any location other than vertical walls.
To protect the performance of the PDP and prevent problems, avoid the following
places:
•
•
•
•
3
Do
Do
Do
Do
not
not
not
not
install
install
install
install
next to smoke and fire detectors.
in an area subjected to vibration.
in an area subjected to high voltage.
near or around any heating apparatus.
1
See the drawing of the wall attachment panel shown in page 14 to check for
the stability of the wall where the PDP is to be installed. If the wall is not
enough strong to support the PDP, strengthen the wall before installation.
2
Fix the wall attachment panel on the wall using bolts as shown in the following
figure: Fixing bolts must protrude from the wall appox. 0.6 inches.
3
Using the wall attachment panel, you may adjust the angle of the display from
0 to 20 degrees. The angle can be set in 5 stages with 5 degrees of distance
each, using the angle control holes on the sides of the panel.
Use only recommended parts and components.
Parts (Wall attachment panel is sold separately. Check with your dealer)
Wall attachment panel
34.61 inches
24.57 inches
When the angle
has been set to 5
degrees.
Angle control holes
When the panel
hasn't been tilted.
When the angle
has been set to
15 degrees.
5 degrees of tilt
10 degrees of tilt
15 degrees of tilt
20 degrees of tilt
No tilt
bolt
Insulation holder
Continued...
14
15
4
Remove four large screws from the rear side of the display.
Separating the Display from the Wall Attachment Panel
Remove the fixing bolts from both sides (left and right) of the wall attachment panel. Lift and pull the
bottom of the display a small amount, to separate the insulation holder point from the bottom of the
wall attachment panel.
Lift the display and separate the insulation holder point from the groove on top of the wall attachment
panel.
Œ
5
Insert the bolts and insulation sinto the four screwholes as shown in the following figure:
ΠBolt
´ Insulation holder
6
´
Put the insulation rubber point protruding from the rear top of the display in
the groove on the top of the wall attachment panel. Lift up the display a little
bit so that the insulation rubber point at the bottom of the rear side of the
display is put in the groove at the bottom of the wall attachment panel.
(Do not lift the display with any pressure. The insulation rubber at the top may
be taken off. )
Œ
´
16
17
Turning the Monitor(PDP) On and Off
Turning the Monitor(PDP) On and Off
Displaying Status Information
Press the Display button on the remote control. The PDP will
display the Screen size, Resolution, Current time, and screen
mode.
Press the Power button on the remote control.
The PDP will be turned on and you will be ready to use it’s
features.
You can also use the Power button on the front of the
PDP.
DISPLAY
Main
SUB
P.MODE
Scaling
S.MODE
Resolution
: Video
: Not Available
: Custom
: Wide
: Custom
: 720 X 480 60Hz
Notes:
• If your Monitor isn’t turned on when the power button is
pressed: Press the MODE button to check if the Monitor
mode has been chosen (
).
Displaying Clock
Press the Clock Display button on the remote control.
The Current time will be displayed on the screen.
Viewing the Menus and Displays
10 : 30 AM
Your PDP has a simple, easy-to-use menu system that appears on the PDP screen. This system makes it convenient and fast to use features on the PDP. Your PDP also lets you display the status of many of your PDP’s
features.
Viewing the Menus
1
With the power on, press the Menu button on the
remote control. The main menu appears on the screen.
The Video menu is selected.
VIDEO
Select
Contrast
Brightness
Sharpness
Color
Tint
R 50
Move
2
18
Custom
100
50
50
50
G 50
Enter
Exit
Use the joystick (up, down) button to move items in the
menu. Use the joystick (left, right) button to display,
change, or use the selected items.
Use the joystick (
) button to enter items in the menu.
On screen menus disappear from the screen
automatically after about thirty seconds, or you can
press the Menu button on your remote control to exit the
menu.
19
P
L
A
S
M
A
D
I
S
P
L
A
Y
P
A
N
E
L
Connections
(Connecting Speakers / Receiver)
Connecting
Connecting
Connecting
Connecting
Speakers ....................................................................22
a VCR/Cable Box ......................................................23
a DVD ......................................................................24
a Set-Top Box..............................................................25
Connecting Speakers
Connecting a VCR/Cable Box
Power Plug
Audio Cable
Speaker Audio Cable
S-Video Cable
Video Cable
✱ External speakers MUST have a power handling capability of 7 watts minimum(impedance 8ohm).
How to Connect
How to Connect
Connect the speaker audio cable to the external speaker output jack on the rear of the PDP,
matching the “+” and “-” ends of the cable with the diagram on the PDP.
1
Connect Video/S-Video cable between the Video/S-Video Output jack on the VCR/Cable
box and the Video Input jack on the PDP.
• For better video, use an S-Video cable.
2
Connect an Audio cable between the Audio Output jacks on the VCR/Cable box and the
Audio Input jacks (Video) on the PDP.
Connecting PDP and Speakers / Stand and Speakers
1
2
Fix the bracket onto the guide pole located on the rear
of speaker and fasten the screws.
• Connecting Speakers to Stands.
1. Turn on PDP and press the Video or S-Video(if S-Video jack is connected.) button on your
remote control.
2. Turn on your VCR, insert a videotape and press the Play button.
After removing the three screws on the PDP, clamp
thespeaker and the PDP together and fasten the screws.
Guide
pole
Videotape Playback:
Guide
pole
Guide
pole
22
23
Connecting a DVD (480i/480p)
Connecting a Set-Top Box(480p/720p/1080i)
Power Plug
Power Plug
Video (Y, Pb, Pr) Cable
Video (Y, Pb, Pr) Cable
Audio Cable
How to Connect
How to Connect
1
Connect a Video cable between the DVD Output jacks on the DVD and the Component1
Video Input (Y,Pb,Pr) Input jacks on the PDP.
1
Connect a Video cable between the Set-Top Box (Y,Pb,Pr) Output jacks on the Set-Top Box and
the Component 2 Video Input (Y,Pb,Pr) Input jacks on the PDP.
2
Connect an Audio cable between the Audio Output jacks on the DVD and the Audio Input
jacks (Component) on the PDP .
2
Connect an Audio cable between the Audio Output jacks on the Set-T op Box and the Audio
Input jacks (Component) on the PDP .
Play to DVD:
24
Audio Cable
To Watch DTV:
1. Turn on PDP and press the Component button to select the Component1 mode.
2. Turn on your DVD, insert a DVD disc and press the Play button.
1. Turn on PDP and press the Component button to select the Component2 mode.
2. Turn on your DTV receiver.
• For an explanation of Component video, see your DVD owner’s instructions.
• For an explanation of Component video, see your DTV receiver owner’s instructions.
25
P
L
A
S
M
A
D
I
S
P
L
A
Y
P
A
N
E
L
Picture Control
Customizing the Picture ................................................................28
Using Automatic Picture Settings ....................................................29
Viewing the Picture-in-Picture..........................................................30
Changing the Screen Size ............................................................33
Freezing the Picture ......................................................................34
1
Customizing the Picture
Using Automatic Picture Settings
You can use the on-screen menus to change the Brightness, Contrast, Sharpness, Color, and
Tint settings of your PDP.
Your PDP has automatic picture settings that allow you to adjust the video display easily.
Press the Menu button, then press the joystick to
enter.
VIDEO
Select
Contrast
Brightness
Sharpness
Color
Tint R 50
Move
2
Move the joystick left or right to select “Custom”.
You will also see the items “Contrast”, “Brightness”,
“Sharpness”, “Color” and “Tint”.
Move the joystick up or down to select the item you
wish to change.
1
!
Quick way to access the picture setting: Just
press “P.Mode” on the remote control.
Adjust
VIDEO
Select
Contrast
Brightness
Sharpness
Color
Tint R 50
Move
2
100
50
50
50
G 50
Move the joystick left or right to select “Custom”,
“Standard”, “Mild”, or “Dynamic” picture setting.
• You can select “High,” “Middle,” “Low,” or
“Custom” in PC mode.
Custom
100
50
50
50
G 50
3
Custom
100
50
50
50
G 50
Adjust
Exit
VIDEO
Select
select
Exit
VIDEO
Adjust
Press the Menu button, then press the joystick to
enter.
Exit
Custom
Select
Contrast
Brightness
Sharpness
Color
Tint R 50
Standard
Exit
Press the Menu button to exit.
Exit
Move the joystick left or right to change the value of
the item.
Contrast
5
Adjust
Select
Contrast
Brightness
Sharpness
Color
Tint R 50
Move
4
100
50
50
50
G 50
VIDEO
Move
3
Custom
60
Press the Menu button to exit.
Note
• In the PC mode, you can’t adjust the sharpness, color and tint.
28
29
Viewing the Picture-in-Picture
Selecting an External Signal
Selecting the PIP Screen
1
You can use PIP to view a signal from an external source, such as a VCR.
Press the Menu button. Move the joystick up or down to
select “PIP”, then press the joystick to enter.
PIP
Select
!
1
Off
Quick way to access the PIP: Just press “PIP”
on the remote control.
Move
Enter
Press the Menu button. Move the joystick up or
down to select “PIP”, then press the joystick to
enter.
!
Exit
PIP
Select
Quick way to access the PIP source: Just press
“Source” in the cover on the remote control.
Move
2
Move the joystick left or right to select “On”.
The PIP image will appear in the corner of the screen.
PIP
Select
2
On
Locate
Source
Move
Move the joystick up or down to select “Source”,
then move the joystick left or right to enter.
3
Adjust
Exit
PIP
Select
On
Locate
Source
Adjust
Exit
Move
Press the Menu button to exit.
On
Locate
Source
3
Adjust
Move the joystick up or down to select an external
signal, then move the joystick left or right.
Exit
PIP
VIDEO
S-VIDEO
Move
Exit
Note
• The PIP function operates in PC mode or Component2 mode only.
30
4
Press the Menu button to exit.
31
Changing the Screen Size
(When entering the Video mode)
Changing the Location of the PIP Image
When you press the Aspect button on the remote control, the PDP’s screen mode should appear in
sequence. The screen displays in this order: Wide, Panorama, Zoom1, Zoom2, Stretch, 4:3.
Note
1
Press the Menu button. Move the joystick up or
down to select “PIP”, then press the joystick to
enter.
!
2
Select
On
Locate
Source
Quick way to access the PIP location: Just press
“Locate” in the cover on the remote control.
Move the joystick up or down to select “Locate”,
then move the joystick left or right to enter.
• If you watch a still image or the 4:3 mode for a long time(over 2 hours), an image may be burned
onto the screen, View the monitor in Wide or Panorama mode as much as possible.
PIP
Move
Adjust
Wide
Zoom2
Sets the picture to 16:9 wide mode.
Magnifies the size of the picture more than
Zoom1.
Panorama
Stretch
Converts regular 4:3 aspect ratio screen to
widescreen.
Moves the Zoom2 picture up a little to fully
show the bottom. Use this picture size if you
want to view the Zoom2 picture along with
captions when watching movies.
Exit
PIP
Select
On
Locate
Source
Move
3
Move the joystick to move the PIP screen where you
want.
Adjust
Exit
PIP
Caption
Adjust
4
Press the Menu button to exit.
Exit
Zoom1
4:3
Magnifies the picture vertically on screen.
Sets the picture to 4:3 normal mode. This is a
standard PDP screen size.
Note
• In VIDEO, S-VIDEO, and Component1 modes, all screen modes can be selected.
(Wide ➝ Panorama ➝ Zoom1 ➝ Zoom2 ➝ Stretch ➝ 4:3).
32
33
Freezing the Picture
Still
Press the Still button on the remote control to freeze a moving picture. Press again to cancel.
P
L
A
S
M
A
D
I
S
P
L
A
Y
P
A
N
E
L
Sound Control
Customizing the Sound ................................................................36
Using Automatic Sound Settings ....................................................37
Using the Surround ......................................................................38
34
Customizing the Sound
1
Press the Menu button. Move the joystick up or
down to select “SOUND”, then press the joystick
to enter.
SOUND
Select
Treble
Bass
Balance
Surround
Move
2
Move the joystick left or right to select “Custom”.
You will also see the items “Treble”, “Bass”,
“Balance” and “Surround”.
Custom
50
50
0
Adjust
Select
Treble
Bass
Balance
Surround
Move the joystick up or down to select the item you
wish to change.
Press the Menu button. Move the joystick up or
down to select “SOUND”, then press the joystick
to enter.
!
Quick way to access the sound setting: Just press
“S.Mode” in the cover on the remote control.
Exit
SOUND
Select
Treble
Bass
Balance
Surround
Move
Custom
50
50
0
2
Move the joystick left or right to select “Custom”,
“Standard”, “Music”, “Movie” or “Speech” sound
setting.
Custom
50
50
0
Off
Adjust
Exit
SOUND
Select
Balance
Surround
Standard
0
Off
Off
Adjust
Move
Exit
SOUND
Select
Treble
Bass
Balance
Surround
Move
1
Off
SOUND
Move
3
Using Automatic Sound Settings
Custom
50
50
0
3
Adjust
Exit
Press the Menu button to exit.
Off
Adjust
Exit
Note
4
• The Automatic Sound Setting function doesn’t operate in PC mode.
Move the joystick left or right to change the value of
the item.
Treble
5
36
60
Press the Menu button to exit.
37
Using the Surround
1
Press the Menu button. Move the joystick up or
down to select “SOUND”, then press the joystick
to enter.
SOUND
Select
Treble
Bass
Balance
Surround
Move
2
Move the joystick up or down to select “Surround”,
then move the joystick left or right to select
“Concert”, “Hall” or “Stadium”.
50
50
0
Off
Adjust
Exit
SOUND
Select
Treble
Bass
Balance
Surround
Move
3
Custom
Custom
50
50
0
Concert
Adjust
Exit
Press the Menu button to exit.
P
L
A
S
M
A
D
I
S
P
L
A
Y
P
A
N
E
L
Time Setting
Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Setting the Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Setting the Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
38
Setting the Clock
Setting the Sleep Timer
This PDP has a built-in clock that will appear on screen when you press the Clock Display button on the
remote control.
1
Press the Menu button. Move the joystick up or
down to select “TIME”, then press the joystick to
enter.
!
2
Quick way to access the Clock Set : Just press
“Clock Set” in the cover on the remote control.
Clock
12 : 00 AM
On time
12 : 00 AM Off
Off time
12 : 00 AM Off
On time volume
10
Sleep Timer
Off
Clock Display
Move the joystick left or right to select minute, then
move the joystick up or down to select the correct
minute.
4
• If you want to display the Clock on screen, move
the joystick down to select “Clock Display”, then
move the joystick right.
!
5
40
Press the Menu button. Move the joystick up or
down to select “TIME”, then press the joystick to
enter.
!
Quick way to access the sleep timer: Just press
“Sleep” in the cover on the remote control.
TIME
Clock
12 : 00 AM
On time
12 : 00 AM Off
Off time
12 : 00 AM Off
On time volume
10
Sleep Timer
Off
Clock Display
Move
Adjust
Exit
Exit
2
Move the joystick up or down to select “Sleep
Timer”.
Clock
10 : 00 AM
On time
12 : 00 AM Off
Off time
12 : 00 AM Off
On time volume
10
Sleep Timer
Off
Clock Display
Move
TIME
Clock
10 : 30 AM
On time
12 : 00 AM Off
Off time
12 : 00 AM Off
On time volume
10
Sleep Timer
Off
Clock Display
Move
Adjust
Exit
Exit
3
TIME
Clock
10 : 30 AM
On time
12 : 00 AM Off
Off time
12 : 00 AM Off
On time volume
10
Sleep Timer
Off
Clock Display
Adjust
Move the joystick left or right to select "AM", then
move the joystick up or down to select “AM” or
“PM”.
Adjust
TIME
Adjust
3
1
TIME
Move
Move the joystick left or right to select hour, then
move the joystick up or down to select the correct
hour.
You can set your PDP to automatically turn off after a preset interval.
Move
Move the joystick left or right to select the time interval for the PDP to stay on. The interval ranges from
10 to 360 minutes.
TIME
Clock
10 : 30 AM
On time
12 : 00 AM Off
Off time
12 : 00 AM Off
On time volume
10
Sleep Timer
10 Min.
Clock Display
Adjust
Move
Exit
Exit
4
TIME
Press the Menu button to exit.
Clock
10 : 30 AM
On time
12 : 00 AM Off
Off time
12 : 00 AM Off
On time volume
10
Sleep Timer
Off
Clock Display
Adjust
Move
Exit
Quick way to access the clock display: Just
press “Clock Display” on the remote control.
Press the Menu button to exit.
41
Setting the Timers
This PDP can be set to turn on or off automatically at specific times that you choose. Before using the
timers, you must set the PDP’s clock, as described previously.
Setting the On/Off Timer
1
Press the Menu button. Move the joystick up or
down to select “TIME”, then press the joystick to
enter.
6
TIME
Clock
12 : 00 AM
On time
12 : 00 AM Off
Off time
12 : 00 AM Off
On time volume
10
Sleep Timer
Off
Clock Display
Move
Adjust
Move the joystick up or down to select “On time”,
then move the joystick left or right.
Exit
TIME
Adjust
Exit
8
3
Move the joystick left or right to select hour, then
move the joystick up or down to select the correct
hour.
Move the joystick left or right to select minute, then
move the joystick up or down to select the correct
minute.
Move the joystick left or right to select “AM”, then
move the joystick up or down to select “AM” or
“PM”.
TIME
Clock
10 : 30 AM
On time
12 : 00 AM Off
Off time
12 : 00 AM Off
On time volume
10
Sleep Timer
Off
Clock Display
Move
Adjust
Exit
Press the Menu button to exit.
Move
Exit
TIME
Clock
10 : 30 AM
On time
6 : 30 AM Off
Off time
12 : 00 AM Off
On time volume
10
Sleep Timer
Off
Clock Display
Move
Exit
TIME
Clock
10 : 30 AM
On time
6 : 30 AM Off
Off time
12 : 00 AM Off
On time volume
10
Sleep Timer
Off
Clock Display
Adjust
42
Exit
TIME
Adjust
5
Move
Clock
10 : 30 AM
On time
6 : 00 AM Off
Off time
12 : 00 AM Off
On time volume
10
Sleep Timer
Off
Clock Display
Adjust
4
If you want to set the Off Time, move the joystick
down to select “Off Time”.
Set the “Off Time” just as you set “On Time”.
• If you want to set the volume level when the PDP
turns on, move the joystick down to select “On
time volume”. Move the joystick right to set the
volume level you want when the PDP turns on.
Clock
10 : 30 AM
On time
12 : 00 AM Off
Off time
12 : 00 AM Off
On time volume
10
Sleep Timer
Off
Clock Display
Move
TIME
Clock
10 : 30 AM
On time
6 : 30 AM On
Off time
12 : 00 AM Off
On time volume
10
Sleep Timer
Off
Clock Display
Adjust
7
2
Move the joystick left or right to select “Off”, then
move the joystick up or down to select “On”.
Move
Exit
43
P
L
A
S
M
A
D
I
S
P
L
A
Y
P
A
N
E
L
Connecting PC and Operation
Connecting to a PC ......................................................................46
Adjusting the PC Screen ................................................................50
Changing the Position of the Image ................................................51
Changing the Size of the Image ....................................................52
Enlarging the Image (Zoom) ..........................................................53
Moving the Zoom Picture ..............................................................54
Picture Quality Adjustment ............................................................55
Information ..................................................................................58
Power Saver (PC mode only)..........................................................59
Connecting to a PC
This PDP is not compatible with Macintosh PC.
Pin Configuration
• 15Pin Signal Cable (based on protruded pin)
Power Plug
PC (15pin)
Cable
Audio Cable
Setting up Your Monitor (Plug and Play)
Our adoption of the new VESA Plug and Play solution eliminates complicated and time consuming
setup. It allows you to install your monitor in a Plug and Play compatible system, without the usual
setup hassles and confusion. Your PC system can easily identify and configure itself for use with your
display. This monitor automatically tells the PC system its Extended Display Identification data (EDID)
using Display Data Channel (DDC) protocols.
Connecting a PC to the PDP
1
2
Connect a PC (15pin) cable between the Video Output jack on the PC and the PC Input jack
(15p D-SUB) on the PDP.
• For an explanation of Component video, see your PC owner’s instructions.
Connect a Audio cable between the Audio Output jack on the PC and the Audio Input (PC)
on the PDP.
To watch the PC screen:
1. Turn on PDP and press the RGB button on the remote to select the PC mode.
2. Turn on PC and check for PC system requirements.
(Refer to pages 48 and 49 for PC system requirements.)
3. Adjust the PC screen. (Refer to page 50.)
46
47
How to Set up Your PC Software (Windows only)
The Windows display-settings for a typical computer are shown below. However, the actual screens on
your PC will probably be different, depending upon your particular version of Windows and your particular video card. But even if your actual screens look different, the same, basic set-up information will
apply in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.)
Notes:
Both screen position and size will vary, depending on the type of PC monitor and its resolution. The table
below shows all of the display modes that are supported:
Video signal
On the windows screen, select in the following
sequence : Start ➝ Settings ➝ Control Panel.
Dot X Line
Vertical
Frequency (Hz)
Horizontal
Frequency (KHz)
Vertical
polarity
Horizontal
polarity
640 X 350
70.086
31.469
N
P
85.080
37.861
N
P
640 X 400
85.080
37.861
P
N
720 X 400
70.087
31.469
P
N
85.039
37.927
P
N
59.940
31.469
N
N
72.809
37.861
N
N
75.000
37.500
N
N
85.008
43.269
N
N
56.250
35.156
N/P
N/P
60.317
37.879
P
P
72.188
48.077
P
P
75.000
46.875
P
P
85.061
53.674
P
P
60.004
48.363
N
N
70.069
56.476
N
N
75.029
60.023
P
P
84.997
68.677
P
P
640 X 480
IBM PC / AT
Compatible
800 X 600
When the control panel screen appears, click on
“Display” and a display dialog-box will appear.
1024 X 768
Select the “Settings” tab in the display dialog-box.
The two key variables that apply the PDP-PC interface are “resolution” and “colors.” The correct settings for these two variables are:
• Size (sometimes called “resolution”):
640 x 480 pixels.
• Color: “24-bit” color (might also be expressed
as “16 million colors”)Shown at left is a typical
screen for “Display” dialog box.
• The interlace mode is not supported.
• The PDP operates abnormally if a non-standard video format is selected.
Notes:
• When this PDP is used as a PC display, 24-bit color is supported (over 16 million colors).
• Depending on the manufacturer, y our PC display screen might appear different.
(and depending on your particular version of Windows).
Check your PC instruction book for information about connecting your PC to a PDP.
• If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 31.5kHZ (horizontal).
If a vertical-frequency option exists on your display settings dialog box, the correct value is “60”
or “60 Hz.” Otherwise, just click “OK” and exit
the dialog box.
• In some cases, abnormal signals (such as stripes) might appear on the screen when the PC power is turned
off (or if the PC is disconnected). If so, press the Source button to enter the VIDEO mode.
Also, make sure that the PC is connected.
• Connect only a PC monitor to the monitor output port while viewing the PC screen. (Otherwise, random
signals might appear).
Continued...
48
49
Adjusting the PC Screen
Changing the Position of the Image
Adjusting the R.G.B
After connecting the PDP to your PC, adjust the position of the screen if it is not well-aligned.
Preset:
• Press the RGB button to select the PC mode.
Preset:
1
• Press the RGB button to select the PC mode.
1
Press the Menu button, then press the joystick to
enter.
VIDEO
Select
Contrast
Brightness
Color Control
Move
2
Move the joystick up or down to select “Color
Control”, then move the joystick left or right to enter.
Custom
100
50
Adjust
Select
Contrast
Brightness
Color Control
Move
2
Adjust
Adjust
Exit
Exit
Press the Menu button to exit.
Move the joystick right or left to change the value of
the item, using the on-screen gauge as your guide.
50
50
50
Adjust
Exit
VIDEO
R
G
B
Move
50
Move the joystick left or right to select “Position”,
then adjust the position of screen by using the
joystick button.
VIDEO
Move
5
Exit
100
50
R
G
B
4
Adjust
English
Wide
Custom
3
Move the joystick up or down to select the item you
want to change.
Position
Language
Scaling
Zoom/Panning
Image Lock
Miscellaneous
Exit
VIDEO
Move
3
Press the Menu button. Move the joystick up or
down to select “SETUP”, then press the joystick
to enter.
70
50
50
Adjust
Exit
Press the Menu button to exit.
51
Changing the Size of the Image
Enlarging the Image (Zoom)
Preset:
Preset:
• Press the RGB button to select the PC mode.
• Press the RGB button to select the PC mode.
1
Press the Menu button. Move the joystick up or
down to select “SETUP” , then press the joystick to
enter.
!
2
Quick way to access the Size: Just press
“Scaling” in the cover on the remote control.
Move the joystick up or down to select “Scaling”,
then move the joystick left or right to select “Wide”
or “4:3”.
Position
Language
Scaling
Zoom/Panning
Image Lock
Miscellaneous
Move
Position
Language
Scaling
Zoom/Panning
Image Lock
Miscellaneous
Press the Menu button to exit.
Adjust
Press the Menu button. Move the joystick up or
down to select “SETUP”, then press the joystick to
enter.
!
Exit
Quick way to access the Zoom: Just press
“Zoom/Pan” in the cover on the remote control.
Position
Language
Scaling
Zoom/Panning
Image Lock
Miscellaneous
Move
2
Move
3
Adjust
English
Wide
1
Move the joystick up or down to select “Zoom/Panning”, then move the joystick left or right to enter.
English
Wide
Adjust
Position
Language
Scaling
Zoom/Panning
Image Lock
Miscellaneous
Move
Adjust
Exit
English
Wide
Exit
Exit
3
Move the joystick left or right to enlarge the image.
• The picture can be expanded 0 to 10 in Zoom
mode.
Zoom
Panning
Move
4
52
English
Wide
5
Adjust
Exit
Press the Menu button to exit.
53
Moving the Zoom Picture
Picture Quality Adjustment
Picture Automatic Adjustment On/Off
Preset:
• Press the RGB button to select the PC mode.
1
Press the Menu button. Move the joystick up or
down to select “SETUP”, then press the joystick to
enter.
!
Quick way to access the Panning : Just press
“Zoom/Pan” in the cover on the remote control.
Position
Language
Scaling
Zoom/Panning
Image Lock
Miscellaneous
Move
2
Move the joystick up or down to select “Zoom/Panning”, then move the joystick left or right to enter.
Move the joystick up or down to select “Panning”,
then move the joystick left or right to enter.
Adjust the position of screen by using the joystick
button.
• The Panning feature operates only when the picture is in Zoom mode.
• Press the RGB button to select the PC mode.
Exit
1
Press the Menu button. Move the joystick up or
down to select “SETUP”, then press the joystick to
enter.
!
Position
Language
Scaling
Zoom/Panning
Image Lock
Miscellaneous
Move
3
Adjust
Preset:
English
Wide
Adjust
Quick way to access the Auto Adjust: Just press
“Auto Adjust.” in the cover on the remote control.
Position
Language
Scaling
Zoom/Panning
Image Lock
Miscellaneous
Move
Move
Exit
2
Move the joystick up or down to select “Image
Lock”, then move the joystick left or right to enter.
Position
Language
Scaling
Zoom/Panning
Image Lock
Miscellaneous
4
54
Adjust
English
Wide
Exit
5
Adjust
Exit
3
Move the joystick up or down to select “Auto
Adjust”, then move the joystick left or right.
The message “Auto in progress” appears on the
screen and the picture adjustments are automatically
activated.
Auto Adjustment
Frequency
Phase
Move
Adjust
Exit
English
Wide
Move
Zoom
Panning
Adjust
English
Wide
Exit
4
Adjust
0
0
Exit
Press the Menu button to exit.
Press the Menu button to exit.
55
Frequency Adjustment
Fine Tuning (Phase)
Preset:
Preset:
• Press the RGB button to select the PC mode.
• Press the RGB button to select the PC mode.
1
Press the Menu button. Move the joystick up or
down to select “SETUP”, then press the joystick to
enter.
Position
Language
Scaling
Zoom/Panning
Image Lock
Miscellaneous
Move
2
Move the joystick up or down to select “Image
Lock”, then move the joystick left or right to enter.
Position
Language
Scaling
Zoom/Panning
Image Lock
Miscellaneous
Move
3
Remove picture noise (vertical stripes) on the screen
by moving the joystick left or right.
(If frequency is not set properly, vertical stripes
will appear on the screen.)
56
Adjust
Press the Menu button. Move the joystick up or
down to select “SETUP”, then press the joystick to
enter.
Exit
Position
Language
Scaling
Zoom/Panning
Image Lock
Miscellaneous
Move
2
English
Wide
Move the joystick up or down to select “Image
Lock”, then move the joystick left or right to enter.
Exit
Auto Adjustment
Frequency
Phase
Frequency
Press the Menu button to exit.
Adjust
English
Wide
0
0
Adjust
English
Wide
Exit
English
Wide
Exit
Move the joystick up or down to select “Phase”.
Remove picture noise (vertical stripes) on the screen
by moving the joystick left or right.
(If phase is not set properly, the picture may be
blurry.)
Exit
Auto Adjustment
Frequency
Phase
Move
Phase
50
4
Adjust
Position
Language
Scaling
Zoom/Panning
Image Lock
Miscellaneous
Move
3
Move
4
Adjust
1
Adjust
0
0
Exit
50
Press the Menu button to exit.
57
Information
Power Saver (PC mode only)
Preset:
This monitor has a built-in power management system called Power Saver. This power management
system saves energy by switching your monitor into a low-power mode when it has not been used for a
certain amount of time. This power management system operates with a VESA DPMS compliant video
card installed in your computer. You use a software utility installed on your computer to set up this feature. See the table below for details.
• Press the RGB button to select the PC mode.
1
Press the Menu button. Move the joystick up or
down to select “SETUP”, then press the joystick to
enter.
Position
Language
Scaling
Zoom/Panning
Image Lock
Miscellaneous
Move
2
Move the joystick up or down to select “Miscellaneous”, then move the joystick left or right to
enter.
Adjust
Position
Language
Scaling
Zoom/Panning
Image Lock
Miscellaneous
Move
3
English
Wide
Table 1. Power-saving modes
English
Wide
Adjust
Exit
Power-saving Function Mode
Normal
Operation
Standby Mode
Suspend Mode
Position A1
Horizontal Sync
Active
Inactive
Active
Inactive
Vertical Sync
Active
Active
Inactive
Inactive
Video
Active
Blanked
Blanked
Blanked
Power
Green
Red Blinking
Red Blinking
Red Blinking
(1 sec Interval)
(1 sec Interval)
(1 sec Interval)
State
Exit
Indicator
Power-off Mode
Position A2
Notes:
Move the joystick up or down to select “Information”, then move the joystick left or right to enter.
• This monitor automatically returns to normal operation when horizontal and vertical sync return.
• This occurs when moving the computer’s mouse or pressing a key on the keyboard.
Information
Key Lock
Move
Resolution
Frequency
• For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.
Off
Adjust
Horizontal
640
31.5KHz
Exit
Vertical
480
60Hz
Exit
4
58
Press the Menu button to exit.
59
P
L
A
S
M
A
D
I
S
P
L
A
Y
P
A
N
E
L
Function Description
Selecting a Menu Language . .
Setting the Multi Control . . . . .
Using the Key Lock . . . . . . . .
Setting up Your Remote Control
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.62
.63
.64
.65
Selecting a Menu Language
1
Press the Menu button. Move the joystick up or
down to select “SETUP”, then press the joystick
to enter.
SETUP
Language
Color Tone
Key Lock
Move
2
Move the joystick left or right to select the appropriate language: English, Spanish, or French.
Setting the Color Tone
English
Normal
Off
Adjust
1
Press the Menu button. Move the joystick up or
down to select “SETUP”, then press the joystick
to enter.
Exit
SETUP
Language
Color Tone
Key Lock
Move
2
3
Adjust
Move the joystick up or down to select “Color Tone”.
Language
Color Tone
Key Lock
3
Exit
SETUP
Move
Press the Menu button to exit.
English
Normal
Off
English
Normal
Off
Adjust
Exit
Move the joystick left or right to select the Color
Tone : Normal, Warm1, Warm2, Cool1, Cool2.
Warm1
4
Press the Menu button to exit.
Note
• In the PC mode, you can’t adjust the Color Tone.
62
63
Using the Key Lock
Setting up Your Remote Control
When Key Lock is set to ON, the buttons (SOURCE, MENU, VOLUME, SELECT , MUTE, POWER) on
the front of the PDP will not operate. However, these buttons will operate when setting Key Lock OFF .
1
Press the Menu button. Move the joystick up or
down to select “SETUP”, then press the joystick
to enter.
SETUP
Language
Color Tone
Key Lock
This PDP's remote control can operate almost any VCR, cable box, or DVD. After it has been set up
properly, your remote control can operate in four different modes :Monitor, VCR, Cable, or DVD.
Pressing the corresponding button on the remote control allows you to switch between these modes,
and control whichever piece of equipment you choose.
Note:The remote control may not be compatible with all DVD Players, VCRs, and Cable boxes.
English
Normal
Off
Setting Up the Remote to Operate Your VCR, Cable box, or DVD player
Move
Move the joystick up or down to select “Key Lock”,
then move the joystick left or right to select
“On” or “Off”.
2
Adjust
Exit
1
Turn off your VCR. (or Cable box, DVD player.)
2
Press the MODE button and make sure that the VCR
(or Cable box, DVD) LED is illuminated.
3
Press the Set button on your PDP's remote control.
4
Using the number buttons on your remote control,
enter three digits of the VCR (or Cable box, DVD)
code listed on page 64 of this manual for your
brand of VCR (or Cable box, DVD player). Make
sure you enter three digits of the code, even if the
first digit is a "0".
(If more than one code is listed, try the first one.)
5
Press the Power button on the remote control.
Your VCR (or Cable box, DVD player) should turn
on if your remote is set up correctly. If your VCR (or
Cable box, DVD player) does not turn on after set
up, repeat steps 2, 3, and 4, but try one of the other
codes listed for your brand of VCR (or Cable box,
DVD player).
If no other codes are listed, try each code, 000
through 089 (or Cable box: 0000 through 077,
DVD player: 000 through 008).
SETUP
Language
Color Tone
Key Lock
Move
English
Normal
On
Adjust
Exit
S.Sel
3
Press the Menu button to exit.
Notes
• When your remote control is in “VCR” mode, the VCR control buttons (Stop, REW, Play/Pause, FF)
still operate your VCR.
64
• When your remote control is in “Cable box” or “DVD” mode, the VCR control buttons (Stop, REW,
Play/Pause, FF) still operate your VCR.
65
Remote Control Codes
VCR Codes
P
L
A
S
M
A
D
I
S
P
L
A
Y
P
A
N
E
L
Cable Box Codes
Appendix
Troubleshooting............................................................................68
Care and Maintenance ................................................................69
Specifications ..............................................................................70
DVD Codes
66
Care and Maintenance
Troubleshooting
Before you call a service technician, please scan this list of problems and possible solutions. It may save you
time and money.
With proper care, your PDP will give you many years of service. Please follow these guidelines to get
the maximum performance from your PDP.
Identifying Problems
Problem
Possible Solution
•
•
•
•
Do not put the PDP near extremely hot, cold, humid or dusty places.
Do not put the PDP near appliances that create magnetic fields.
Keep the ventilation openings clear.
Do not place the PDP on a rough and slanted surface, such as cloth or paper.
Poor picture.
Check all wire connections.
The power indicator is
blinking amber.
The monitor is using its power management system.
Check the power management utility on your computer.
Your Remote control does not
operate the monitor.
Press the “Mode” button to put your remote control in the
“Monitor” mode.
• Never open the cabinet or touch the parts inside.
• Wipe your PDP with a clean, dry cloth. Never use water, cleaning fluids, wax, or chemicals.
• Do not put heavy objects on top of the cabinet.
The monitor won’t turn on.
Make sure the wall outlet is working.
Temperature
Liquids
• Do not place liquids near or on the PDP.
Cabinet
68
There is no screen image.
Check to see that both the monitor and the source are plugged
in and turned on.
The image is too light or
too dark.
Adjust the Brightness or Contrast settings.
The image is too large or
too small.
Adjust the Size settings.
The message "Check Temp"
blinks on the screen and then
the picture switches OFF.
The PDP is overheated. Power off the PDP and let it cool for a
while.
The message "Check Fan”
blinks on the screen and then
the picture switches OFF.
The cooling fan of the PDP may have a problem. Contact an
authorized service center.
• If your PDP is suddenly moved from a cold to a warm place, unplug the power cord for at least two
hours so that moisture that may have formed inside the unit can dry completely.
69
Specifications
Memo
Exterior design and product specifications are subject to change without prior notice to improve the
performance of this product.
This PDP applies to Class B digital device.
(Note: Class B system is for home use.)
This PDP has been registered for residential use in terms of EMI. So it can be used in all areas as well
as residential areas.
SPL4225
Model
Dimensions
Display
Remote Control
Weight
Display
Remote Control
Voltage
Power Consumption
Number of Pixels
1038.8 (W) X 89 (D) X 635 (H) mm ; 40.90 (W) X 3.50 (D) X 25.00(H) inches
54 (W) X 31.5 (D) X 220 (H) mm ; 2.13 (W) X 1.24 (D) X 8.66 (H) inches
32kg ; 70.55lbs
150g (including batteries) ; 0.33lbs
100-240V~, 50/60Hz, 4A
310 Watts
852(H) x 480(V)
Screen Size
106 Cm/42 inches
AUDIO input
VIDEO / S-VIDEO
COMPONENT 1
COMPONENT 2
PC (RGB)
AUDIO output
7W + 7W (8 Ω)
VIDEO input
VIDEO
S-VIDEO
COMPONENT 1 - 480i / 480p
COMPONENT 2 - 480p/720p/1080i
RGB : D-SUB 15P
70
71