Y
P
O
EOS 70D (W)
Wi-Fi Function
Instruction Manual
C
E
INSTRUCTION
MANUAL
What You Can Do Using the Wireless LAN Functions
This camera’s wireless LAN functions let you perform a range of tasks
wirelessly, from sending images to Web services and other cameras to
controlling the camera remotely, simply by connecting to a Wi-Fi®
network or other device supporting this camera’s wireless LAN functions.
(1) Transfer images
between cameras
Exchange images
(2) Connect to a
smartphone
(6) View images using
a media player
Make images
viewable on a
smartphone
Shoot remotely
with a smartphone
C
Y
P
O
View images
(Canon Image Gateway)
(5) Send images to
a Web service
(3) Print images using
a Wi-Fi printer
Save and share images
Print images
(4) Operate the camera
remotely using EOS Utility
Remotely control the camera
CANON iMAGE GATEWAY Web services are not supported in certain countries
and areas. For information on countries and areas supporting CANON iMAGE
GATEWAY services, refer to the Canon Web site (http://canon.com/cig).
Settings for “Send images to a Web service” may not be performed from
a computer in certain countries and areas.
2
What You Can Do Using the Wireless LAN Functions
(1) z Transfer images between cameras (p.19)
Transfer images between this camera and other Canon cameras
with built-in wireless LAN functions.
(2) q Connect to a smartphone (p.31, 75)
View saved images or operate the camera from your smartphone.
Install the dedicated application “EOS Remote” on your smartphone
to use these functions.
(3) l Print images using a Wi-Fi printer (p.45, 87)
Connect the camera to a wireless LAN compatible printer supporting
PictBridge (Wireless LAN) to print images wirelessly.
(4) D Operate the camera remotely using EOS Utility (p.93)
Y
P
O
Connect the camera and a computer wirelessly and operate your
camera remotely using the provided software EOS Utility.
(5) w Send images to a Web service (p.103)
C
Upload your images to CANON iMAGE GATEWAY, an online photo
service for Canon users (free registration required), to share them
with family and friends.
(6)
View images using a media player (p.131)
Display images on the camera’s memory card on your TV set, by
using a media player supporting DLNA* via a wireless LAN.
* Digital Living Network Alliance
3
Wi-Fi Function Flowchart
Setup
Set up another Canon camera with
built-in wireless LAN functions
Install EOS Remote on a smartphone
Connection
method
q Connect to a smartphone
Connect the cameras directly via a
wireless LAN
• Camera access point mode*1
• Infrastructure mode*2
Now you
can...
z Transfer images between cameras
Transfer images between cameras
l Print images using a Wi-Fi printer
D Operate the camera remotely
using EOS Utility
Setup
Set up a Wi-Fi printer supporting
PictBridge (Wireless LAN)
Set up a wireless LAN and a
computer with EOS Utility installed
Connection
method
• Camera access point mode*1
• Infrastructure mode*2
• Infrastructure mode*2
• Ad hoc mode*3
Now you
can...
C
Y
P
O
• View images on the camera
• Shoot remotely
Play and print images
Operate the camera remotely using
EOS Utility
4
Wi-Fi Function Flowchart
• Set up devices supporting DLNA
and a wireless LAN access point
• Connect a media player to a TV set
Infrastructure mode*2
Infrastructure mode*2
• Send images to Web services
• Send Emails to your acquaintances
Setup
• Set up a computer with EOS Utility
installed and a wireless LAN access
point that can access the Internet
• Sign up as a CANON iMAGE
GATEWAY member
• Configure the camera for Web
service access
Connection
method
View images using a media
player
Now you
can...
w Send images to a Web service
C
Y
P
O
View images on the camera by
operating the media player
*1 Camera access point mode:
A simple wireless LAN mode where a camera and smartphone, or a camera and
printer can be directly connected via a wireless LAN.
*2 Infrastructure mode:
A wireless LAN mode that connects to each Wi-Fi device via a wireless LAN access
point. In this mode, communication to a distant Wi-Fi device can be established as
long as a wireless LAN access point is located nearby.
*3 Ad hoc mode:
A wireless LAN mode that connects directly to a computer with built-in wireless LAN
functions. When setting the computer’s wireless LAN functions to ad hoc mode, the
camera can be connected using the same operation as when set to infrastructure
mode.
CANON iMAGE GATEWAY Web services are not supported in certain
countries and areas. For information on countries and areas supporting
CANON iMAGE GATEWAY services, refer to the Canon Web site
(http://canon.com/cig).
Settings for “Send images to a Web service” may not be performed from
a computer in certain countries and areas.
5
Conventions Used in This Manual
In this manual, the term “wireless LAN” is used as a general term for
Wi-Fi and Canon’s original wireless communication functions.
The term “access point” indicates wireless LAN terminals (wireless
LAN access points or wireless LAN adapters) that relay wireless
LAN connection.
Brackets [ ] indicate buttons or icon names or other software
elements displayed on the computer screen. Brackets also indicate
camera menu items.
The ** (numbers) for “(p.**)” in this manual indicate reference page
numbers for more information.
Sections of this manual labeled with the following symbols contain
particular types of information as described below.
: Warnings to prevent potential problems during operation.
Y
P
O
: Additional information provided to supplement the content about
basic operations.
C
Microsoft and Windows are trademarks or registered trademarks of
Microsoft Corporation in the United States and/or other countries.
Macintosh and Mac OS are trademarks of Apple Inc., registered in the U.S.
and other countries.
Wi-Fi is a registered trademark of the Wi-Fi Alliance.
Wi-Fi Certified, WPA, WPA2, and the Wi-Fi Certified logo are trademarks of
the Wi-Fi Alliance.
WPS used on camera settings screens and in this manual stands for Wi-Fi
Protected Setup.
UPnP is a trademark of the UPnP Implementers Corporation.
All other trademarks are the property of their respective owners.
Note that Canon cannot be held liable for any loss or damage from erroneous
wireless LAN settings for using the camera. In addition, Canon cannot be held
liable for any other loss or damage caused by use of the camera.
6
Chapters
Introduction
1
2
3
4
5
6
7
8
9
10
11
12
13
14
2
Basic Settings for Wireless LAN Functions
11
Transferring Images Between Cameras
19
Connecting to a Smartphone - 1
31
Printing Images Using a Wi-Fi Printer - 1
45
Using a Wi-Fi Wireless LAN Access Point
55
Connecting to a Smartphone - 2
75
Printing Images Using a Wi-Fi Printer - 2
87
Remote Operation Using EOS Utility
93
C
Y
P
O
Sending Images to a Web Service
103
Viewing Images Using a Media Player
131
Using Quick Control to Connect to a Wireless LAN
139
Managing Settings
145
Troubleshooting Guide
151
Reference
169
7
Contents
Introduction
2
What You Can Do Using the Wireless LAN Functions ..................... 2
Wi-Fi Function Flowchart.................................................................. 4
Conventions Used in This Manual.................................................... 6
Chapters........................................................................................... 7
1
Basic Settings for Wireless LAN Functions
11
Registering a Nickname ................................................................. 12
Basic Operation and Settings ......................................................... 15
2
Transferring Images Between Cameras
19
Selecting the Connection Destination ............................................ 20
Y
P
O
Sending Images ............................................................................. 22
Reconnecting ................................................................................. 26
Registering Multiple Connection Settings....................................... 27
C
Changing Setting Names ............................................................... 28
3
Connecting to a Smartphone - 1
31
Preparation..................................................................................... 32
Using Camera Access Point Mode to Establish a Connection ....... 33
Operating the Camera Using a Smartphone .................................. 37
Reconnecting ................................................................................. 39
Specifying Viewable Images .......................................................... 40
Registering Multiple Connection Settings....................................... 43
4
Printing Images Using a Wi-Fi Printer - 1
45
Using Camera Access Point Mode to Establish a Connection ....... 46
Printing ........................................................................................... 50
Reconnecting ................................................................................. 51
Registering Multiple Connection Settings....................................... 52
8
Contents
5
Using a Wi-Fi Wireless LAN Access Point
55
Checking the Type of Access Point ................................................ 56
Easy Connection via WPS (PBC Mode) ......................................... 57
Easy Connection via WPS (PIN Mode)........................................... 62
Manual Connection by Searching Networks ................................... 67
6
Connecting to a Smartphone - 2
75
Using Infrastructure Mode to Establish a Connection..................... 76
Operating the Camera Using a Smartphone................................... 78
Reconnecting .................................................................................. 80
Specifying Viewable Images ........................................................... 81
Y
P
O
Registering Multiple Connection Settings ....................................... 84
7
Printing Images Using a Wi-Fi Printer - 2
87
Using Infrastructure Mode to Establish a Connection..................... 88
C
Printing............................................................................................ 90
Reconnecting .................................................................................. 91
Registering Multiple Connection Settings ....................................... 92
8
Remote Operation Using EOS Utility
93
Configuring EOS Utility Communication Settings ........................... 94
Using EOS Utility ............................................................................ 98
Reconnecting .................................................................................. 99
Registering Multiple Connection Settings ..................................... 100
9
Sending Images to a Web Service
103
Preparation ................................................................................... 104
Checking the Type of Access Point .............................................. 106
Easy Connection via WPS (PBC Mode) ....................................... 107
Easy Connection via WPS (PIN Mode)......................................... 111
9
Contents
Manual Connection by Searching Networks ................................ 115
Sending Images to a Web Service ............................................... 120
Reconnecting ............................................................................... 126
Registering Multiple Connection Settings..................................... 127
10
Viewing Images Using a Media Player
131
Configuring Media Player Communication Settings ..................... 132
Displaying Images on a TV set..................................................... 133
Reconnecting ............................................................................... 135
Registering Multiple Connection Settings..................................... 136
11
Using Quick Control to Connect to a Wireless LAN
Y
P
O
139
Connecting from Quick Control .................................................... 140
Connecting from a Playback Screen ............................................ 141
12
Managing Settings
C
145
Checking or Changing Settings.................................................... 146
Clearing Wireless LAN Settings ................................................... 149
13
Troubleshooting Guide
151
Responding to Error Messages .................................................... 152
Troubleshooting Guide ................................................................. 163
Wireless LAN Notes ..................................................................... 164
Checking Network Settings .......................................................... 166
14
Reference
169
Specifications ............................................................................... 170
Index............................................................................................. 171
10
Basic Settings for
Wireless LAN Functions
Y
P
O
This chapter describes settings necessary for using the
camera’s wireless LAN functions.
C
11
Registering a Nickname
First, set the camera’s nickname.
When the camera is connected to another device via a wireless LAN,
the nickname will be displayed on the device. Be sure to set a nickname
for your camera.
1
Select [Wi-Fi].
Under the [53] tab, select [Wi-Fi],
then press <0>.
[Enable].
2 Select
Press the <V> key to select
[Enable], then press <0>.
Y
P
O
X [Wi-Fi function] is now selectable.
C
[Wi-Fi function].
3 Select
Under the [53] tab, select [Wi-Fi
function], then press <0>.
X When this setting is selected for the
first time, a screen to register a
nickname is displayed. Select [OK]
and proceed on to step 4.
12
Registering a Nickname
a nickname.
4 Enter
For instructions on entering
characters, see “Virtual Keyboard
Operation” on the next page.
Up to 16 characters can be entered.
5 Finish.
When you are finished, press the
<M> button.
Select [OK] on the confirmation
screen, then press <0>. The
nickname is registered, and the [WiFi function] screen will appear.
C
Y
P
O
To change the nickname, press the
<B> button on the screen above,
then select [Edit nickname] on the
screen displayed.
13
Registering a Nickname
Virtual Keyboard Operation
Switching to other input areas
To switch between top and bottom
input areas, press the <Q> button.
Moving the cursor
To move the cursor, press the <U>
key in the top area.
Entering text
In the bottom input area, press the <V> or <U> key to select
characters and press <0> to enter them.
You can check how many characters you have entered, and how
many more can be entered, by referring to [*/*] on the upper right of
the screen.
Y
P
O
Switching to other input modes*
Select [
] at the lower right of the bottom area. Each time you
press <0>, the input mode changes. The input mode changes in
the following order: lower-case characters9numbers/symbols 1
9numbers/symbols 29upper-case characters.
C
* When [Touch control: Disable] is set, you can enter all characters on one
screen.
Deleting text
Press the <L> button to erase one character.
Finishing text entry
Press the <M> button to confirm what you have entered and
exit. If a confirmation screen is displayed, select [OK] to exit.
Canceling text entry
Press the <B> button to cancel text entry and exit. If a
confirmation screen is displayed, select [OK] to exit.
14
Basic Operation and Settings
Using the Camera While Wireless LAN Functions Are Active
When you want to prioritize wireless LAN functions, do not operate
the shutter button, Mode Dial, or playback button. Otherwise,
shooting or playback operation may be prioritized and wireless LAN
functions may be terminated during the process. Also, the
connection may be terminated when the LCD monitor is closed
facing inward.
When [Wi-Fi] in the [53] tab is set to [Enable], movie shooting is
disabled. Even if the camera is connected to a computer, printer,
GPS receiver, or other device via an interface cable, they cannot be
used (p.17).
Auto Power Off
C
Y
P
O
If necessary, set [Auto power off]
under the [52] tab to [Disable].
If the camera’s auto power off is
activated during the wireless LAN
connection, the wireless LAN function
will turn off. Wireless LAN connection
is restored when the camera wakes
up from auto power off.
[Wi-Fi] Under the [53] Tab
When the use of electronic devices
and wireless devices is prohibited,
such as on board airplanes or in
hospitals, set [Wi-Fi] to [Disable].
15
Basic Operation and Settings
[Wi-Fi] Settings and Connection Status
Settings and connection status for [Wi-Fi] under the [53] tab can be
checked on the camera’s LCD monitor and LCD panel.
Wi-Fi function
Wi-Fi function
Wi-Fi connection status
When [Wi-Fi] is set to
[Disable]
When [Wi-Fi] is set to
[Enable] but there is no
connection
Y
P
O
LCD monitor
LCD panel
Wi-Fi connection
Wi-Fi function
status
Wi-Fi function
C
(Off)
(Off)
(Off)
Connected
Data is being
transmitted
(IJ)
Waiting for connection/
Waiting for
reconnection
(Blinking)
Connection error
(Blinking)
(Blinking)
(Blinking)
(Blinking)
16
Basic Operation and Settings
Touch Control
You can operate wireless LAN functions by touching the screen as well.
For details, refer to “Using the Touch Screen” in the Camera Instruction
Manual.
C
Y
P
O
Connecting with an Interface Cable
When [53: Wi-Fi] is set to [Enable], interface cable connection is
disabled. Set it to [Disable] to connect the interface cable.
When the camera is connected to a computer, printer, GPS receiver, or
any other devices via an interface cable, the settings for [Wi-Fi] cannot
be changed. Disconnect the interface cable and then configure settings.
Using an Eye-Fi Card
When [53: Wi-Fi] is set to [Enable], image transfer using an Eye-Fi card
is disabled.
17
MEMO
C
18
Y
P
O
Transferring Images
Between Cameras
Y
P
O
Images can be transferred between Canon cameras via
the built-in wireless LAN functions.
C
Wireless connection is possible for Canon cameras with built-in
wireless LAN functions marketed in 2012 or later. Note that the
camera cannot be connected to Canon camcorders, even if they
have built-in wireless LAN functions.
The camera cannot be connected to Canon cameras without
built-in wireless LAN functions, even if they support Eye-Fi
cards.
Still photos can be transferred only if their file format is JPEG.
Although movies can be transferred, some target cameras may
not be able to play them back depending on their functionality.
19
Selecting the Connection Destination
Register the target camera to connect to via a wireless LAN. The
camera can be connected to only one camera at a time.
1
Select [Wi-Fi function].
Under the [53] tab, set [Wi-Fi] to
[Enable], then select [Wi-Fi
function].
[z].
2 Select
Press the <V> or <U> key to
select [z] (Transfer imgs between
cameras), then press <0>.
Y
P
O
the connection on the target
3 Start
camera.
C
When the screen on the left is
displayed on the camera, start the
connection on the target camera as
well. For the operation procedure,
refer to the instruction manual of the
target camera.
When a connection is established,
the settings are automatically saved
and an image on the card is
displayed.
20
Selecting the Connection Destination
the images to send.
4 Select
Select images on the camera sending
the images (p.22).
Do not operate the camera receiving
the images.
C
Y
P
O
Note that GPS information is not displayed on the camera’s playback screen
even if GPS information is appended to the received image. Shooting
locations can be viewed on a virtual map, using the Map Utility software.
The connection settings are automatically saved/registered with the
nickname of the camera to which a connection was established.
Auto power off does not function when the camera is connected to
another camera.
21
Sending Images
Sending Images One by One
Selected images are sent one by one.
1
Select an image to send.
Press the <U> key to select an
image to send, then press <0>.
You can also press the <I>
button to select an image in the index
display. To return to the single-image
display, press the <u> button.
[Send img shown].
2 Select
To select a size at which to send the
image, select [Resize image] and
press <0>.
Press the <U> key to select [Send
img shown], then press <0>.
X The transfer progress screen is
displayed.
To send another image, repeat steps
1 and 2.
C
Y
P
O
connection.
3 Terminate
Press the <M> button to display
the confirmation screen. Press the
<U> key to select [OK], then press
<0> to terminate the connection.
X The [Wi-Fi function] screen will
reappear.
If playback or shooting operation is started during the connection, the
connection will be terminated.
RAW images cannot be sent.
22
Sending Images
Sending Selected Images
Multiple images can be selected and sent.
1
Press <0>.
[Send selected].
2 Select
To select a size at which to send the
images, select [Resize image] and
press <0>.
Press the <U> key to select [Send
selected], then press <0>.
Y
P
O
the images to send.
3 Select
Press the <U> key to select the
C
images to send, then press <0>.
X <X> is displayed on the upper left of
the image to send.
You can also press the <I>
button to select an image in the threeimage display. To return to the singleimage display, press the <u> button.
After selecting the images to send,
press the <Q> button.
23
Sending Images
the image size.
4 Reduce
Set it if necessary.
For the setting procedures, see the
next page.
the images.
5 Send
Press the <V> key to select [Send],
then press <0> to send the images.
X The transfer progress screen is
displayed.
To send another image, repeat steps
1 to 5.
Y
P
O
connection.
6 Terminate
Press the <M> button to display
the confirmation screen. Press the
<U> key to select [OK], then press
<0> to terminate the connection.
X The [Wi-Fi function] screen will
reappear.
C
If playback or shooting operation is started during the connection, the
connection will be terminated. Operations such as shooting cannot be
performed when data is being sent or received. When [Cancel] is
selected on the camera being used to send images, image transfer is
stopped so that shooting and other operations can be performed.
When sending a large number of images or large files (total size), make
sure that the battery is adequately charged so it does not run out during
the process.
RAW images cannot be sent.
You can select up to 50 files.
24
Sending Images
Reducing the Size of the Image to Send
When [Send selected] is selected, the confirmation screen for sending
images also lets you select the size at which to send them.
1
Select [Resize images to send].
On the confirmation screen for
sending images, press the <V> key
to select [Resize images to send],
then press <0>.
the image size.
2 Select
Press the <V> key to select an
image size, then press <0>.
Y
P
3O
C
Send the images.
Press the <V> key to select [Send],
then press <0> to send the images.
All images to be sent at the same time are resized except those that are
already smaller than the selected image size.
Movies cannot be resized.
[Resize:S2] and [Resize:S3] are enabled only for still photos shot with
the EOS 70D. Images shot with other cameras are sent without resizing.
The file size (total size) is based on the file sizes before resizing the
images.
25
Reconnecting
The camera can reconnect to another camera for which connection
settings have been registered.
1
Select [Wi-Fi function].
Under the [53] tab, set [Wi-Fi] to
[Enable], then select [Wi-Fi
function].
[z].
2 Select
Select [z] (Transfer imgs between
cameras) and press <0>.
Y
P
O
a connection.
3 Establish
Select [Connect] and press <0>.
C
On the confirmation screen, select [OK].
Perform the reconnection procedure
on the target camera as well.
X The images on the card are displayed
and the images to send can be selected.
When settings for multiple connection
destinations are registered, select
[Choose set.], select the connection
destination, then connect to the
destination.
By default, settings are named after
the nickname of the camera that was
connected to.
If Wi-Fi settings on the target camera are cleared (p.149), reconnection will
no longer be established. Select [Review/change settings] and change the
settings (p.148).
26
Registering Multiple Connection Settings
You can register up to three camera connection settings.
1
Select [Wi-Fi function].
Under the [53] tab, set [Wi-Fi] to
[Enable], then select [Wi-Fi
function].
[z].
2 Select
Select [z] (Transfer imgs between
cameras) and press <0>.
Y
P
O
[Choose set.].
3 Select
Select [Choose set.] and press
C
<0>.
[Unspecified].
4 Select
Select [Unspecified] and press
<0>.
X The connection settings screen is
displayed. Follow the procedures
displayed to complete the connection
settings.
The name of the setting can be changed later (p.28).
27
Changing Setting Names
The names displayed for reconnection settings can be changed after
the settings are completed.
1
Select [Wi-Fi function].
Under the [53] tab, set [Wi-Fi] to
[Enable], then select [Wi-Fi
function].
[z].
2 Select
Select [z] (Transfer imgs between
cameras) and press <0>.
Y
P
O
[Review/change settings].
3 Select
Select [Review/change settings]
C
and press <0>.
[Change settings name].
4 Select
Select [Change settings name] and
press <0>.
28
Changing Setting Names
the setting name.
5 Change
Change the name of the setting using
the virtual keyboard (p.14). Up to 30
characters can be entered.
When you are finished, press the
<M> button.
Select [OK] on the confirmation
screen and press <0> to complete
the change.
C
Y
P
O
29
MEMO
C
30
Y
P
O
Connecting to a
Smartphone - 1
Y
P
O
Connecting the camera to a smartphone lets you use
the smartphone to view, manage, and receive images
stored in the camera. You can also use the smartphone
to perform remote shooting. Note that movie shooting is
disabled.
C
31
Preparation
EOS Remote Installation Required
To communicate with a smartphone, the camera needs to be connected
to the smartphone using the dedicated application EOS Remote.
EOS Remote can be downloaded from the App Store or Google
Play. Install EOS Remote on the smartphone and then perform the
procedures to establish the connection.
To use EOS Remote, a smartphone on which iOS or Android
installed is necessary. For information on supported operating
system, refer to the download site of EOS Remote software.
C
32
Y
P
O
Using Camera Access Point Mode to Establish a Connection
The camera and smartphone can be directly connected via a wireless
LAN.
Because the camera acts as an access point, no other access point is
necessary, so you can establish communications easily even when you
are out.
To establish connection, operations on the smartphone are required.
For details, refer to the smartphone instruction manual.
1
Select [Wi-Fi function].
Under the [53] tab, set [Wi-Fi] to
[Enable], then select [Wi-Fi
function].
Y
P
O
[q].
2 Select
Select [q] (Connect to smartphone)
and press <0>.
C3
Select [Camera access point
mode].
Press the <V> key to select
[Camera access point mode], then
press <0>.
Select [OK] and press <0> to go to
the next screen.
[Easy connection].
4 Select
Press the <V> key to select [Easy
connection], then press <0>.
Select [OK] and press <0> to go to
the next screen.
For manual connection, see page 36.
33
Using Camera Access Point Mode to Establish a Connection
the smartphone to the
5 Connect
camera.
On the Wi-Fi settings menu of the
smartphone, select the SSID
(network name) displayed on the
camera’s LCD monitor.
For the password, enter the
encryption key displayed on the
camera’s LCD monitor.
X The next screen may be
automatically displayed even when
the operation on the smartphone is
not completed.
Y
P
O
EOS Remote on the
6 Start
smartphone.
When the Wi-Fi settings are
completed, start EOS Remote on the
smartphone.
C
[Camera Connection] on
7 Select
the smartphone.
Select [Camera Connection] on
EOS Remote.
the target camera on the
8 Select
smartphone.
Select the camera to connect to from
the [Detected Cameras] on EOS
Remote.
X Pairing starts.
34
Using Camera Access Point Mode to Establish a Connection
to the camera.
9 Connect
When pairing is completed, the
screen on the left is displayed. Press
the <U> key to select [OK], then
press <0>.
To specify viewable images (p.40),
press the <B> button.
Non-alphanumeric characters
are displayed as 8.
further settings.
10 Perform
To finish settings in this stage, press
C
the <V> key to select [OK], then
press <0> to go to step 11.
To change the name of the settings,
select [Settings name] and press
<0>.
X The virtual keyboard is displayed
(p.14). Up to 30 characters can be
entered for the name of the settings.
Y
P
O
the settings.
11 Save
Select [OK] and press <0> to save
the settings.
X The [qConnection] screen will be
displayed.
To return to the menu, press the
<M> button.
The settings for communicating with a smartphone are now complete.
35
Using Camera Access Point Mode to Establish a Connection
When [Manual connection] Is Selected
If you have selected [Manual connection] in step 4 on page 33, set
[SSID], [Channel setting], and [Encryption settings] on each screen
displayed.
1
Enter an SSID.
Enter any character using the virtual
keyboard (p.14).
When you are finished, press the
<M> button.
[Auto setting].
2 Select
Select [Auto setting] and press
<0>.
Select [OK] and press <0> to go to
the next screen.
To select manually, select [Manual
setting] and turn the <6> dial.
C
Y
P
O
[None].
3 Select
Select [None] and press <0>.
Select [OK] and press <0>. The
screen shown in step 5 on page 34
will appear.
For encryption, select [AES], then
enter any encryption key using the
virtual keyboard (p.14).
36
Operating the Camera Using a Smartphone
You can use a smartphone with EOS Remote installed to view images
stored in the camera and shoot remotely.
EOS Remote Main Screen
The main functions of EOS Remote are
described below. Touch the screen to
learn the operation procedures.
[Camera Image Viewing]
Images stored in the camera can be
viewed.
Images stored in the camera can be
saved on a smartphone.
Operations such as deletion can be
performed on images stored in the
camera.
Y
P
O
[Remote Shooting]
C
The camera’s Live View image can
be viewed using a smartphone.
Camera settings can be changed.
You can shoot using remote
operation.
(Settings button)
Use this button to access various
settings for EOS Remote.
When viewable images are specified (p.40), functions of EOS Remote
will be limited.
Shooting may not be possible when the camera is connected to a
smartphone.
When you perform remote shooting, set the Live View shooting/Movie
shooting switch to <A>.
37
Operating the Camera Using a Smartphone
Terminating the Connection
1
Select [Exit].
If the screen on the left is not
displayed, select [Wi-Fi function]
under the [53] tab.
Select [Exit] and press <0>.
[OK].
2 Select
Press the <U> key to select [OK],
then press <0> to terminate the
connection.
C
Y
P
O
JPEG and RAW images are resized and saved as JPEG images in the
most appropriate format for smartphones.
Although movies are included in the list, they cannot be saved.
If the camera’s auto power off is activated during the wireless LAN
connection, the wireless LAN function will turn off. Wireless LAN
connection is restored when the camera wakes up from auto power off.
When you establish a connection, deactivating the smartphone’s power
saving function is recommended.
38
Reconnecting
The camera can reconnect to a smartphone for which connection
settings have been registered.
1
Select [Wi-Fi function].
Under the [53] tab, set [Wi-Fi] to
[Enable], then select [Wi-Fi
function].
[q].
2 Select
Select [q] (Connect to smartphone)
and press <0>.
Y
P
O
a connection.
3 Establish
Select [Connect] and press <0>.
C
On the confirmation screen, select
[OK].
X The camera will reconnect to the
smartphone.
When settings for multiple connection
destinations are registered, select
[Choose set.], select the connection
destination, then connect to the
destination.
39
Specifying Viewable Images
You can specify images viewable from a smartphone by operating the
camera. Images can be specified during connection settings or after the
connection is terminated.
1
Select [Wi-Fi function].
Under the [53] tab, set [Wi-Fi] to
[Enable], then select [Wi-Fi
function].
[q].
2 Select
Select [q] (Connect to smartphone)
and press <0>.
Y
P
O
[Review/change settings].
3 Select
Select [Review/change settings]
C
and press <0>.
[Viewable imgs].
4 Select
Select [Viewable imgs] and press
<0>.
40
Specifying Viewable Images
an item.
5 Select
Press the <V> key to select an item,
then press <0>.
Select [OK] and press <0> to
display the setting screen.
[All images]
All images stored on the card become viewable.
[Images from past days]
Specify viewable images on the
shooting-date basis. Images shot up to
nine days ago can be specified.
Press the <V> key to select an item,
then press <0>.
When [Images shot in past days] is
selected, images shot up to the
specified number of days before the
current date become viewable. When
<r> is shown for the number of
days, turn the <5> dial to specify the
number of days, then press <0> to
confirm the selection.
Select [OK] and press <0> to
specify the viewable images.
C
Y
P
O
[Select by rating]
Specify viewable images depending on
whether a rating has been added (or not
added) or by the type of rating.
Press the <V> key to select a
rating, then press <0> to specify the
viewable images.
41
Specifying Viewable Images
[File number range] (Select range)
First image Last image
Select the first and last images from
images arranged by the file number to
specify the viewable images.
1 Press the <U> key to select the
first image to be set viewable.
2 Press <0> to display the image
selection screen.
Select an image using the <U>
key, <5> dial, or <6> dial.
You can also press the <I>
button to select an image in the index
display. To return to the single-image
display, press the <u> button.
3 Select an image and press <0> to
determine the selection.
4 Specify the last image to be set
viewable by the same operation.
Select an image shot later than the
image selected as the first image.
5 When the first and last images are
specified, press the <V> key to
select [OK], then press <0>.
C
42
Y
P
O
Registering Multiple Connection Settings
You can register up to three smartphone connection settings.
1
Select [Wi-Fi function].
Under the [53] tab, set [Wi-Fi] to
[Enable], then select [Wi-Fi
function].
[q].
2 Select
Select [q] (Connect to smartphone)
and press <0>.
Y
P
O
[Choose set.].
3 Select
Select [Choose set.] and press
C
<0>.
[Unspecified].
4 Select
Select [Unspecified] and press
<0>.
X The connection settings screen is
displayed. Follow the procedures
displayed to complete the connection
settings.
43
MEMO
C
44
Y
P
O
4
Printing Images Using
a Wi-Fi Printer - 1
Y
P
O
You can directly print images by connecting the camera
with a wireless LAN compatible printer supporting
PictBridge (Wireless LAN) via a wireless LAN.
C
Images can be printed by connecting this camera with a
printer by PictBridge via a wireless LAN. PictBridge is a
standard for easily printing images by directly connecting
digital cameras to printers and other devices supporting
the standard.
45
Using Camera Access Point Mode to Establish a Connection
The camera and a printer can be directly connected via a wireless LAN.
Because the camera acts as an access point, no other access point is
necessary, so you can print images easily no matter where you are.
To connect via a Wi-Fi access point, see “Using a Wi-Fi Wireless LAN
Access Point” (p.55).
1
Select [Wi-Fi function].
Under the [53] tab, set [Wi-Fi] to
[Enable], then select [Wi-Fi
function].
[l].
2 Select
Select [l] (Print from Wi-Fi printer)
Y
P
O
and press <0>.
C
[Camera access point
3 Select
mode].
Press the <V> key to select
[Camera access point mode], then
press <0>.
Select [OK] and press <0> to go to
the next screen.
[Easy connection].
4 Select
Press the <V> key to select [Easy
connection], then press <0>.
Select [OK] and press <0> to go to
the next screen.
For manual connection, see page 49.
46
Using Camera Access Point Mode to Establish a Connection
the printer’s Wi-Fi settings to
5 Set
connect to the camera.
On the Wi-Fi settings menu of the
printer to be used, select the SSID
(network name) displayed on the
camera’s LCD monitor.
For the password, enter the
encryption key displayed on the
camera’s LCD monitor.
For the printer operation procedure,
refer to the printer’s instruction
manual.
the printer to connect to.
6 Select
When a list of detected printers is
C
Y
P
O
displayed, select the printer to
connect to and press <0>.
X Some printers may make a beeping
sound.
When 16 or more printers are
detected or search takes over 3
minutes, you can select [Search
again].
47
Using Camera Access Point Mode to Establish a Connection
further settings.
7 Perform
To finish settings in this stage, press
the <V> key to select [OK], then
press <0> to go to step 8.
To change the name of the settings,
select [Settings name] and press
<0>.
X The virtual keyboard is displayed
(p.14). Up to 30 characters can be
entered for the name of the settings.
Y
P
O
the settings.
8 Save
Select [OK] and press <0> to save
the settings.
X The [lConnection] screen will be
C
displayed.
To return to the menu, press the
<M> button.
The settings for communicating with a printer are now complete.
48
Using Camera Access Point Mode to Establish a Connection
When [Manual connection] Is Selected
If you have selected [Manual connection] in step 4 on page 46, set
[SSID], [Channel setting], and [Encryption settings] on each screen
displayed.
1
Enter an SSID.
Enter any character using the virtual
keyboard (p.14).
When you are finished, press the
<M> button.
[Auto setting].
2 Select
Select [Auto setting] and press
C
<0>.
Select [OK] and press <0> to go to
the next screen.
To select manually, select [Manual
setting] and turn the <6> dial.
Y
P
O
[None].
3 Select
Select [None] and press <0>.
Select [OK] and press <0>. The
screen shown in step 5 on page 47
will be displayed.
For encryption, select [AES], then
enter any encryption key using the
virtual keyboard (p.14).
49
Printing
Play back an image.
Press the <x> button.
X An image is displayed and the <w>
icon appears on the upper left of the
screen indicating that the printer is
connected.
For further operations, refer to
“Printing Images” in the Camera
Instruction Manual. You can also
perform “Direct Printing of PrintOrdered Images”.
Terminating the Connection
1
Y
P
O
Select [Exit].
If the screen on the left is not
displayed, select [Wi-Fi function]
under the [53] tab.
Select [Exit] and press <0>.
C
[OK].
2 Select
Press the <U> key to select [OK],
then press <0> to terminate the
connection.
50
Reconnecting
The camera can reconnect to a printer for which connection settings
have been registered.
1
Select [Wi-Fi function].
Under the [53] tab, set [Wi-Fi] to
[Enable], then select [Wi-Fi
function].
[l].
2 Select
Select [l] (Print from Wi-Fi printer)
and press <0>.
Y
P
O
a connection.
3 Establish
Select [Connect] and press <0>.
C
On the confirmation screen, select
[OK].
X The camera will reconnect to the
printer.
When settings for multiple connection
destinations are registered, select
[Choose set.], select the connection
destination, then connect to the
destination.
51
Registering Multiple Connection Settings
You can register up to three printer connection settings.
1
Select [Wi-Fi function].
Under the [53] tab, set [Wi-Fi] to
[Enable], then select [Wi-Fi
function].
[l].
2 Select
Select [l] (Print from Wi-Fi printer)
and press <0>.
Y
P
O
[Choose set.].
3 Select
Select [Choose set.] and press
<0>.
C
[Unspecified].
4 Select
Select [Unspecified] and press
<0>.
X The connection settings screen is
displayed. Follow the procedures
displayed to complete the connection
settings.
52
MEMO
C
Y
P
O
53
MEMO
C
54
Y
P
O
Using a Wi-Fi Wireless
LAN Access Point
Y
P
O
Connecting to a Wi-Fi wireless LAN access point gives
you access to the following functions:
•
•
•
•
•
Connecting to a smartphone
Printing images using a Wi-Fi printer
Remote operation using EOS Utility
Sending images to a Web service*
Viewing images using a media player
C
* To send images to a Web service, skip the explanation in this chapter
and see page 103.
Connecting to a Smartphone
To use [q] (Connect to smartphone), the dedicated
application EOS Remote must be installed on the
smartphone in advance. EOS Remote can be downloaded
from the App Store or Google Play.
To use EOS Remote, a smartphone on which iOS or
Android installed is necessary. For information on
supported operating system, refer to the download site of
EOS Remote software.
55
Checking the Type of Access Point
When Wi-Fi Protected Setup (WPS) is supported
• p.57: Easy Connection via WPS (PBC Mode)
• p.62: Easy Connection via WPS (PIN Mode)
When WPS is not supported
• p.67: Manual Connection by Searching Networks
If you do not know if the access point you use is WPS-compatible, refer
to the access point instruction manual or other documentation.
C
Y
P
O
When connecting to a network that has a network administrator, ask the
administrator about the detailed setting procedures.
If the network you use filters by MAC address, register the MAC address of
the camera at the access point. The MAC address can be checked on the
[General sett.] screen (p.149).
56
Easy Connection via WPS (PBC Mode)
This is a connection mode available when using an access point
compatible with Wi-Fi Protected Setup (WPS). In pushbutton
connection mode (PBC mode), the camera and the access point can be
connected simply by pressing the WPS button on the access point.
Note that if multiple access points are active in the surrounding area, it
may be more difficult to establish a connection. In this case, try using
[WPS (PIN mode)] to establish a connection.
Check the position of the WPS button on the access point in advance.
It may take approx. one minute to establish a connection.
If stealth functions of the access point are enabled, connection
may be disabled. Deactivate stealth functions.
1
Select [Wi-Fi function].
Under the [53] tab, set [Wi-Fi] to
[Enable], then select [Wi-Fi
function].
Y
P
2O
C
Select an item.
Select either [q] [D] [l] or [
then press <0>.
],
57
Easy Connection via WPS (PBC Mode)
[Infrastructure mode].
3 Select
Displayed when [q] or [l] is
selected. Go to step 4 when selecting
[D] or [ ].
Press the <V> key to select
[Infrastructure mode], then press
<0>.
Select [OK] and press <0> to go to
the next screen.
[WPS (PBC mode)].
4 Select
Press the <V> key to select [WPS
(PBC mode)], then press <0>.
Select [OK] and press <0> to go to
the next screen.
Y
P
O
to the access point.
5 Connect
Press the access point’s WPS button.
C
For details about where the button is
located and how long to press it, refer
to the access point’s instruction
manual.
Select [OK] and press <0> to
establish a connection with the
access point.
X When a connection with the access
point is established, the [IP address
set.] screen is displayed.
the IP address.
6 SetPress
the <V> key to select the IP
address setting method, then press
<0>.
58
Easy Connection via WPS (PBC Mode)
[Auto setting]
Configures the settings available in [Manual setting] automatically.
However, this option can only be used in environments using DHCP
servers, or access points or routers with DHCP server functionality,
such that IP addresses and related settings are assigned and
configured automatically.
Select [OK] and press <0> to display the setting screen for the
communication method (p.60).
If an error is displayed even though the IP address and related
settings is set to be automatically assigned and configured, select
[Manual setting].
[Manual setting]
If [Auto setting] results in an error, enter the IP address manually.
Enter the IP address assigned to the camera when prompted for the IP
address.
Select [OK] and then select an item on the screen displayed. When
finished, press <0>.
When entering numbers, turn the <6>
dial to move the input position in the
upper area and turn the <5> dial to
select the number. Press <0> to enter
the selected number. When you have
finished entering information, press the
<M> button. A confirmation screen
is not displayed.
When you have completed setting all items, select [OK] and press
<0>. The setting screen for the communication method will be
displayed (p.60).
If you are not sure what to enter, see “Checking Network Settings”
(p.166), or ask the network administrator or another person
knowledgeable about the network.
C
Y
P
O
59
Easy Connection via WPS (PBC Mode)
Specifying Settings for the Communication Method
This section explains setting screens for the communication method of
each device and service that the camera is connected to. Read the
page that introduces the selected communication method.
Connecting to a Smartphone: Chapter 6 (p.75)
Y
P
O
Printing Images Using a Wi-Fi Printer: Chapter 7 (p.87)
C
60
Easy Connection via WPS (PBC Mode)
Remote Operation Using EOS Utility: Chapter 8 (p.93)
Windows 8/7/Vista Users
When operating the camera remotely using EOS Utility, perform the
operations as follows before performing the operations described on page
94 and after. If these operations are not performed, the Pairing Software
described on page 95 may not start.
Open the [C Drive] 9 [Program Files] 9 [Canon] 9 [EOS Utility] 9
[WFTPairing] folder (in this order), and then double-click the [WFT
FirewallSettings] icon. (The folder names above are examples. The
location of files differs according to the environment.) After performing this
operation, perform the operation described on page 94.
C
Y
P
O
Viewing Images Using a Media Player: Chapter 10 (p.131)
61
Easy Connection via WPS (PIN Mode)
This is a connection mode available when using an access point
compatible with Wi-Fi Protected Setup (WPS). In PIN code connection
mode (PIN mode), an 8-digit identification number specified on the
camera is set at the access point to establish a connection.
Even if there are multiple access points active in the surrounding area,
a relatively reliable connection can be established using this shared
identification number.
It may take approx. one minute to establish a connection.
If stealth functions of the access point are enabled, connection
may be disabled. Deactivate stealth functions.
1
Select [Wi-Fi function].
2
Select an item.
Under the [53] tab, set [Wi-Fi] to
[Enable], then select [Wi-Fi
function].
C
Y
P
O
Select either [q] [D] [l] or [
then press <0>.
],
[Infrastructure mode].
3 Select
Displayed when [q] or [l] is
selected. Go to step 4 when selecting
[D] or [ ].
Press the <V> key to select
[Infrastructure mode], then press
<0>.
Select [OK] and press <0> to go to
the next screen.
62
Easy Connection via WPS (PIN Mode)
[WPS (PIN mode)].
4 Select
Press the <V> key to select [WPS
(PIN mode)], then press <0>.
Select [OK] and press <0> to go to
the next screen.
the PIN code at the
5 Specify
access point.
At the access point, specify the 8-digit
PIN code displayed on the camera’s
LCD monitor.
For instructions on setting PIN codes
at the access point, refer to the
access point’s instruction manual.
After the PIN code is specified, select
[OK] and press <0>.
Y
P
6O
C
Connect to the access point.
Select [OK] and press <0> to
establish a connection with the
access point.
X When a connection with the access
point is established, the [IP address
set.] screen is displayed.
the IP address.
7 SetPress
the <V> key to select the IP
address setting method, then press
<0>.
63
Easy Connection via WPS (PIN Mode)
[Auto setting]
Configures the settings available in [Manual setting] automatically.
However, this option can only be used in environments using DHCP
servers, or access points or routers with DHCP server functionality,
such that IP addresses and related settings are assigned and
configured automatically.
Select [OK] and press <0> to display the setting screen for the
communication method (p.65).
If an error is displayed even though the IP address and related
settings is set to be automatically assigned and configured, select
[Manual setting].
[Manual setting]
If [Auto setting] results in an error, enter the IP address manually.
Enter the IP address assigned to the camera when prompted for the IP
address.
Select [OK] and then select an item on the screen displayed. When
finished, press <0>.
When entering numbers, turn the <6>
dial to move the input position in the
upper area and turn the <5> dial to
select the number. Press <0> to enter
the selected number. When you have
finished entering information, press the
<M> button. A confirmation screen
is not displayed.
When you have completed setting all items, select [OK] and press
<0>. The setting screen for the communication method will be
displayed (p.65).
If you are not sure what to enter, see “Checking Network Settings”
(p.166), or ask the network administrator or another person
knowledgeable about the network.
C
64
Y
P
O
Easy Connection via WPS (PIN Mode)
Specifying Settings for the Communication Method
This section explains setting screens for the communication method of
each device and service that the camera is connected to. Read the
page that introduces the selected communication method.
Connecting to a Smartphone: Chapter 6 (p.75)
Y
P
O
Printing Images Using a Wi-Fi Printer: Chapter 7 (p.87)
C
65
Easy Connection via WPS (PIN Mode)
Remote Operation Using EOS Utility: Chapter 8 (p.93)
Windows 8/7/Vista Users
When operating the camera remotely using EOS Utility, perform the
operations as follows before performing the operations described on page
94 and after. If these operations are not performed, the Pairing Software
described on page 95 may not start.
Open the [C Drive] 9 [Program Files] 9 [Canon] 9 [EOS Utility] 9
[WFTPairing] folder (in this order), and then double-click the [WFT
FirewallSettings] icon. (The folder names above are examples. The
location of files differs according to the environment.) After performing this
operation, perform the operation described on page 94.
C
Y
P
O
Viewing Images Using a Media Player: Chapter 10 (p.131)
66
Manual Connection by Searching Networks
Selecting the Wireless Network
When [Find network] is selected, a list of active access points nearby
is displayed, accompanied by information about them. Select the SSID
(or ESS-ID) of the access point to connect to.
1
Select [Wi-Fi function].
Under the [53] tab, set [Wi-Fi] to
[Enable], then select [Wi-Fi
function].
an item.
2 Select
Select either [q] [D] [l] or [
Y
P
O
],
then press <0>.
C3
Select [Infrastructure mode].
Displayed when [q] or [l] is
selected. Go to step 4 when selecting
[D] or [ ].
Press the <V> key to select
[Infrastructure mode], then press
<0>.
Select [OK] and press <0> to go to
the next screen.
[Find network].
4 Select
Press the <V> key to select [Find
network], then press <0>.
Select [OK] and press <0> to go to
the next screen.
67
Manual Connection by Searching Networks
(1)
(2) (3)
(4)
an access point.
5 Select
Press <0> to enable the selection of
an access point.
Press the <V> key to select an
access point, then press <0>.
Select [OK] and press <0> to go to
the next screen (p.69).
(1) Indicates whether the device is in infrastructure or ad hoc mode
(2) An icon is displayed if the access point is encrypted
(3) First characters of the SSID
(4) Channel used
Access Point Encryption
Y
P
O
This camera supports the following options for [Authentication] and
[Encryption settings]. Therefore, the encryption used by the access
point should be one of the following.
[Authentication]: Open system, Shared key, WPA-PSK, or WPA2PSK
[Encryption settings]: WEP, TKIP, or AES
C
[Enter connection] and [Search again]
To configure settings for the access point manually, select [Enter
connection] and press <0>. Enter the SSID using the virtual
keyboard and then configure settings following the instructions
displayed.
To search for access points again, select [Search again] and press
<0>.
68
Manual Connection by Searching Networks
Entering the Wireless LAN Encryption Key
Go to the next page when the [IP address set.] screen is displayed.
Set the encryption key specified for the access point. For details on the
specified encryption key, refer to the access point’s instruction manual.
Note that the screens displayed in steps 1 to 3 below vary depending on
the authentication and encryption specified for the access point.
1
2
C
3
The [Key index] screen is displayed
only if WEP encryption is used by the
access point.
Press the <V> key to select the key
index number specified for the access
point, then press <0>.
Select [OK] and press <0> to go to
the next screen.
Y
P
O
Press the <V> key to select the
format and the number of characters
used for the key, then press <0>.
Select [OK] and press <0> to go to
the next screen.
Enter the encryption key using the
virtual keyboard (p.14).
X The [IP address set.] screen (p.70)
will be displayed.
69
Manual Connection by Searching Networks
Setting the IP Address
Press the <V> key to select how the
IP address should be set, then press
<0>.
[Auto setting]
Configures the settings available in [Manual setting] automatically.
However, this option can only be used in environments using DHCP servers,
or access points or routers with DHCP server functionality, such that IP
addresses and related settings are assigned and configured automatically.
Select [OK] and press <0> to display the setting screen for the
communication method (p.71).
If an error is displayed even though the IP address and related
settings is set to be automatically assigned and configured, select
[Manual setting].
[Manual setting]
C
Y
P
O
If [Auto setting] results in an error, enter the IP address manually. Enter the
IP address assigned to the camera when prompted for the IP address.
Select [OK] and then select an item on the screen displayed. When
finished, press <0>.
When entering numbers, turn the <6>
dial to move the input position in the
upper area and turn the <5> dial to
select the number. Press <0> to enter
the selected number. When you have
finished entering information, press the
<M> button. A confirmation screen
is not displayed.
When you have completed setting all items, select [OK] and press
<0>. The setting screen for the communication method will be
displayed (p.71).
70
Manual Connection by Searching Networks
If you are not sure what to enter, see “Checking Network Settings”
(p.166), or ask the network administrator or another person
knowledgeable about the network.
Specifying Settings for the Communication Method
This section explains setting screens for the communication method of
each device and service that the camera is connected to. Read the
page that introduces the selected communication method.
Connecting to a Smartphone: Chapter 6 (p.75)
C
Y
P
O
Printing Images Using a Wi-Fi Printer: Chapter 7 (p.87)
71
Manual Connection by Searching Networks
Remote Operation Using EOS Utility: Chapter 8 (p.93)
Windows 8/7/Vista Users
When operating the camera remotely using EOS Utility, perform the
operations as follows before performing the operations described on page
94 and after. If these operations are not performed, the Pairing Software
described on page 95 may not start.
Open the [C Drive] 9 [Program Files] 9 [Canon] 9 [EOS Utility] 9
[WFTPairing] folder (in this order), and then double-click the [WFT
FirewallSettings] icon. (The folder names above are examples. The
location of files differs according to the environment.) After performing this
operation, perform the operation described on page 94.
C
Y
P
O
Viewing Images Using a Media Player: Chapter 10 (p.131)
72
MEMO
C
Y
P
O
73
MEMO
C
74
Y
P
O
Connecting to a
Smartphone - 2
Y
P
O
Connecting the camera to a smartphone lets you use
the smartphone to view, manage, and receive images
stored in the camera. You can also use the smartphone
to perform remote shooting. Note that movie shooting is
disabled.
C
These instructions should be followed only after the
smartphone is connected to an access point. For
information about settings and configuration, refer to the
documentation provided with each device or contact the
manufacturer.
75
Using Infrastructure Mode to Establish a Connection
These instructions are continued from Chapter 5.
To establish connection, operations on the smartphone are required.
For details, refer to the smartphone’s instruction manual.
To connect in the camera access point mode, see “Using Camera
Access Point Mode to Establish a Connection” (p.33).
1
Start EOS Remote on the
smartphone.
When the screen on the left is
displayed on the camera, start EOS
Remote on the smartphone.
[Camera Connection] on
2 Select
the smartphone.
Y
P
O
Select [Camera Connection] on
EOS Remote.
C
the camera to connect to
3 Select
on the smartphone.
Select the camera to connect to from
the [Detected Cameras] on EOS
Remote.
If multiple cameras are displayed,
identify the camera to connect to by
its MAC address displayed on the
camera’s LCD monitor.
The MAC address can also be
checked on the [General sett.]
screen (p.149).
X Pairing starts.
76
Using Infrastructure Mode to Establish a Connection
to the camera.
4 Connect
When pairing is completed, the
screen on the left is displayed. Press
the <U> key to select [OK], then
press <0>.
To specify viewable images (p.81),
press the <B> button.
Non-alphanumeric characters
are displayed as 8.
further settings.
5 Perform
To finish settings in this stage, press
C
the <V> key to select [OK], then
press <0> to go to step 6.
To change the name of the settings,
select [Settings name] and press
<0>.
X The virtual keyboard is displayed
(p.14). Up to 30 characters can be
entered for the name of the settings.
Y
P
O
the settings.
6 Save
Select [OK] and press <0> to save
the settings.
X The [qConnection] screen will be
displayed.
To return to the menu, press the
<M> button.
The settings for networking with the smartphone are now complete.
77
Operating the Camera Using a Smartphone
You can use a smartphone with EOS Remote installed to view images
stored in the camera and shoot remotely.
EOS Remote Main Screen
The main functions of EOS Remote are
described below. Touch the screen to
learn the operation procedures.
[Camera Image Viewing]
Images stored in the camera can be
viewed.
Images stored in the camera can be
saved on a smartphone.
Operations such as deletion can be
performed on images stored in the
camera.
Y
P
O
[Remote Shooting]
C
The camera’s Live View image can
be viewed using a smartphone.
Camera settings can be changed.
You can shoot using remote
operation.
(Settings button)
Use this button to access various
settings for EOS Remote.
When viewable images are specified (p.81), functions of EOS Remote
will be limited.
Shooting may not be possible when the camera is connected to a
smartphone.
When you perform remote shooting, set the Live View shooting/Movie
shooting switch to <A>.
78
Operating the Camera Using a Smartphone
Terminating the Connection
1
Select [Exit].
If the screen on the left is not
displayed, select [Wi-Fi function]
under the [53] tab.
Select [Exit] and press <0>.
[OK].
2 Select
Press the <U> key to select [OK],
then press <0> to terminate the
connection.
C
Y
P
O
JPEG and RAW images are resized and saved as JPEG images in the
most appropriate format for smartphones.
Although movies are included in the list, they cannot be saved.
If the camera’s auto power off is activated during the wireless LAN
connection, the wireless LAN function will turn off. Wireless LAN
connection is restored when the camera wakes up from auto power off.
When you establish a connection, deactivating the smartphone’s power
saving function is recommended.
79
Reconnecting
The camera can reconnect to a smartphone for which connection
settings have been registered.
1
Select [Wi-Fi function].
Under the [53] tab, set [Wi-Fi] to
[Enable], then select [Wi-Fi
function].
[q].
2 Select
Select [q] (Connect to smartphone)
and press <0>.
Y
P
O
a connection.
3 Establish
Select [Connect] and press <0>.
C
On the confirmation screen, select
[OK].
X The camera will reconnect to the
smartphone.
When settings for multiple connection
destinations are registered, select
[Choose set.], select the connection
destination, then connect to the
destination.
80
Specifying Viewable Images
You can specify images viewable from a smartphone by operating the
camera. Images can be specified during connection settings or after the
connection is terminated.
1
Select [Wi-Fi function].
Under the [53] tab, set [Wi-Fi] to
[Enable], then select [Wi-Fi
function].
[q].
2 Select
Select [q] (Connect to smartphone)
and press <0>.
Y
P
O
[Review/change settings].
3 Select
Select [Review/change settings]
C
and press <0>.
[Viewable imgs].
4 Select
Select [Viewable imgs] and press
<0>.
81
Specifying Viewable Images
an item.
5 Select
Press the <V> key to select an item,
then press <0>.
Select [OK] and press <0> to
display the setting screen.
[All images]
All images stored on the card become viewable.
[Images from past days]
Specify viewable images on the
shooting-date basis. Images shot up to
nine days ago can be specified.
Press the <V> key to select an item,
then press <0>.
When [Images shot in past days] is
selected, images shot up to the
specified number of days before the
current date become viewable. When
<r> is shown for the number of
days, turn the <5> dial to specify the
number of days, then press <0> to
confirm the selection.
Select [OK] and press <0> to
specify the viewable images.
C
Y
P
O
[Select by rating]
Specify viewable images depending on
whether a rating has been added (or not
added) or by the type of rating.
Press the <V> key to select a
rating, then press <0> to specify the
viewable images.
82
Specifying Viewable Images
[File number range] (Select range)
First image Last image
Select the first and last images from
images arranged by the file number to
specify the viewable images.
1 Press the <U> key to select the
first image to be set viewable.
2 Press <0> to display the image
selection screen.
Select an image using the <U>
key, <5> dial, or <6> dial.
You can also press the <I>
button to select an image in the index
display. To return to the single-image
display, press the <u> button.
3 Select an image, then press <0> to
determine the selection.
4 Specify the last image to be set
viewable by the same operation.
Select an image shot later than the
image selected as the first image.
5 When the first and last images are
specified, press the <V> key to
select [OK], then press <0>.
C
Y
P
O
83
Registering Multiple Connection Settings
You can register up to three smartphone connection settings.
1
Select [Wi-Fi function].
Under the [53] tab, set [Wi-Fi] to
[Enable], then select [Wi-Fi
function].
[q].
2 Select
Select [q] (Connect to smartphone)
and press <0>.
Y
P
O
[Choose set.].
3 Select
Select [Choose set.] and press
<0>.
C
[Unspecified].
4 Select
Select [Unspecified] and press
<0>.
X The connection settings screen is
displayed. Follow the procedures
displayed to complete the connection
settings.
84
MEMO
C
Y
P
O
85
MEMO
C
86
Y
P
O
7
Printing Images Using
a Wi-Fi Printer - 2
Y
P
O
You can directly print images by connecting the camera
with a wireless LAN compatible printer supporting
PictBridge (Wireless LAN) via a wireless LAN.
C
These instructions should be followed only after the
printer is connected to an access point. For information
about settings and configuration, refer to the
documentation provided with each device or contact the
manufacturer.
Images can be printed by connecting this camera with a
printer by PictBridge via a wireless LAN. PictBridge is a
standard for easily printing images by directly connecting
digital cameras to printers and other devices supporting
the standard.
87
Using Infrastructure Mode to Establish a Connection
These instructions are continued from Chapter 5.
To connect in camera access point mode, see “Using Camera Access
Point Mode to Establish a Connection” (p.46).
1
Select the printer to connect to.
When a list of detected printers is
displayed, select the printer to
connect to and press <0>.
X Some printers may make a beeping
sound.
When 16 or more printers are
detected or search takes over 3
minutes, you can select [Search
again].
Y
P
O
further settings.
2 Perform
To finish settings in this stage, press
the <V> key to select [OK], then
press <0> to go to step 3.
To change the name of the settings,
select [Settings name] and press
<0>.
X The virtual keyboard is displayed
(p.14). Up to 30 characters can be
entered for the name of the settings.
C
88
Using Infrastructure Mode to Establish a Connection
3
Save the settings.
Select [OK] and press <0> to save
the settings.
X The [lConnection] screen will be
displayed.
To return to the menu, press the
<M> button.
The settings for networking with the printer are now complete.
C
Y
P
O
89
Printing
Play back an image.
Press the <x> button.
X An image is displayed and the <w>
icon appears on the upper left of the
screen indicating that the printer is
connected.
For further operations, refer to
“Printing Images” in the Camera
Instruction Manual. You can also
perform “Direct Printing of PrintOrdered Images”.
Terminating the Connection
1
Y
P
O
Select [Exit].
If the screen on the left is not
displayed, select [Wi-Fi function]
under the [53] tab.
Select [Exit] and press <0>.
C
[OK].
2 Select
Press the <U> key to select [OK],
then press <0> to terminate the
connection.
90
Reconnecting
The camera can reconnect to a printer for which connection settings
have been registered.
1
Select [Wi-Fi function].
Under the [53] tab, set [Wi-Fi] to
[Enable], then select [Wi-Fi
function].
[l].
2 Select
Select [l] (Print from Wi-Fi printer)
and press <0>.
Y
P
O
a connection.
3 Establish
Select [Connect] and press <0>.
C
On the confirmation screen, select
[OK].
X The camera will reconnect to the
printer.
When settings for multiple connection
destinations are registered, select
[Choose set.], select the connection
destination, then connect to the
destination.
91
Registering Multiple Connection Settings
You can register up to three printer connection settings.
1
Select [Wi-Fi function].
Under the [53] tab, set [Wi-Fi] to
[Enable], then select [Wi-Fi
function].
[l].
2 Select
Select [l] (Print from Wi-Fi printer)
and press <0>.
Y
P
O
[Choose set.].
3 Select
Select [Choose set.] and press
<0>.
C
[Unspecified].
4 Select
Select [Unspecified] and press
<0>.
X The connection settings screen is
displayed. Follow the procedures
displayed to complete the connection
settings.
92
Remote Operation
Using EOS Utility
Y
P
O
You can perform remote operation using EOS Utility via
a wireless LAN. In addition to remote shooting, various
camera operations are available because a wireless
LAN is used instead of an interface cable. Note that
movie shooting is disabled.
C
These instructions should be followed only after the
computer with EOS Utility installed is connected to an
access point. For information about settings and
configuration, refer to the documentation provided with
each device or contact the manufacturer.
Settings may be disabled when an older version of software is
used. Use the software installed from the CD provided with this
camera.
93
Configuring EOS Utility Communication Settings
These instructions are continued from Chapter 5.
With EOS Utility, you can use the provided Pairing Software to establish
a connection between the camera and a computer.
Pairing Software is installed automatically during “easy installation” of
the software provided with the camera. If it is not installed, install it on
the computer to be connected to the camera in advance.
The configuration procedure is as follows, using Windows 7 as an
example.
1
Select [OK].
First, the pairing screen is displayed.
Press the <U> key to select [OK],
then press <0>. The following
message is displayed.
“******” represents the last six digits of
the MAC address of the camera to be
connected.
C
94
Y
P
O
Configuring EOS Utility Communication Settings
software.
2 StartStartthethepairing
pairing software on the
computer. Normally, it is installed in
the same location as EOS Utility.
X After the pairing software starts up, an
icon is displayed on the task bar.
X When the camera is detected, a
message is displayed.
the pairing software
3 Double-click
icon.
Y
P
O
X Detected cameras are listed.
C4
Cameras that have already been
connected are not included in the list.
Click [Connect].
If multiple cameras are displayed,
identify the camera to connect to by
its MAC address displayed on the
camera’s LCD monitor.
The MAC address can also be
checked on the [General sett.]
screen (p.149).
95
Configuring EOS Utility Communication Settings
[OK].
5 Select
When the camera detects the
computer on which you clicked
[Connect] in step 4, the screen on
the left is displayed.
Press the <U> key to select [OK],
then press <0>.
further settings.
6 Perform
To finish settings in this stage, press
the <V> key to select [OK], then
press <0> to go to step 7.
To change the name of the settings,
select [Settings name] and press
<0>.
X The virtual keyboard is displayed
(p.14). Up to 30 characters can be
entered for the name of the settings.
C
Y
P
O
the settings.
7 Save
Select [OK] and press <0> to save
the settings.
X The [DConnection] screen is
displayed.
To return to the menu, press the
<M> button.
The EOS Utility network settings are now complete.
96
Configuring EOS Utility Communication Settings
There is no need to complete pairing again if you will continue using
a particular camera and computer together after pairing without
changing the settings.
To reconnect to the same computer, simply turn on the camera and
start the pairing software. The connection between the camera and
computer will be established automatically.
You can add the pairing software to the software launched on your
computer at startup. In EOS Utility, select [Preferences] and the
[Basic Settings] tab, then append [Add WFT Pairing Software to
the Startup folder] (for Macintosh, [Register WFT Paring Software
in Login Options]) with a checkmark.
C
Y
P
O
In Remote Live View shooting, the rate of image transmission is slower as
compared to connection via an interface cable. Therefore, the motion of
moving subjects cannot be displayed smoothly.
If the camera’s auto power off is activated during the wireless LAN
connection, the wireless LAN function will turn off. Wireless LAN connection
is restored when the camera wakes up from auto power off.
97
Using EOS Utility
For EOS Utility instructions, refer to the EOS Utility instruction manual
(CD-ROM). In addition to remote shooting, various camera operations
are available. Note that movie shooting is disabled.
C
Y
P
O
Terminating the Connection
1
Select [Exit].
If the screen on the left is not
displayed, select [Wi-Fi function]
under the [53] tab.
Select [Exit] and press <0>.
[OK].
2 Select
Press the <U> key to select [OK],
then press <0> to terminate the
connection.
98
Reconnecting
The camera can reconnect to a computer for which connection settings
have been registered.
1
Select [Wi-Fi function].
Under the [53] tab, set [Wi-Fi] to
[Enable], then select [Wi-Fi
function].
[D].
2 Select
Select [D] (Remote control (EOS
Utility)) and press <0>.
Y
P
O
a connection.
3 Establish
Select [Connect] and press <0>.
C
On the confirmation screen, select
[OK].
X The camera will reconnect to the
computer.
When settings for multiple connection
destinations are registered, select
[Choose set.], select the connection
destination, then connect to the
destination.
99
Registering Multiple Connection Settings
You can register up to three EOS Utility connection settings.
1
Select [Wi-Fi function].
Under the [53] tab, set [Wi-Fi] to
[Enable], then select [Wi-Fi
function].
[D].
2 Select
Select [D] (Remote control (EOS
Utility)) and press <0>.
Y
P
O
[Choose set.].
3 Select
Select [Choose set.] and press
<0>.
C
[Unspecified].
4 Select
Select [Unspecified] and press
<0>.
X The connection settings screen is
displayed. Follow the procedures
displayed to complete the connection
settings.
100
MEMO
C
Y
P
O
101
MEMO
C
102
Y
P
O
Sending Images to
a Web Service
Y
P
O
You can register various Web services on the camera
and send images stored in the camera to them.
C
CANON iMAGE GATEWAY Web services are not supported in
certain countries and areas. For information on countries and
areas supporting CANON iMAGE GATEWAY services, refer to
the Canon Web site (http://canon.com/cig).
Settings for “Send images to a Web service” may not be
performed from a computer in certain countries and areas.
103
Preparation
Signing Up as a CANON iMAGE GATEWAY Member
To send images to Web services, you need to sign up as a CANON
iMAGE GATEWAY member (free of charge).
Once you are a CANON iMAGE GATEWAY member, you can publish
photos you took in online albums and use a range of services. This Web
site also serves as a bridge to send images wirelessly from the camera
or for sending links to the online albums. Connect to the Internet from a
computer or other device, access the CANON iMAGE GATEWAY site
for the area you live in from the Canon Web site (http://canon.com/cig)
and register as a member by following the instructions.
If you also intend to use Web services other than CANON iMAGE
GATEWAY, you must have an account with the services you intend to
use. For details, consult each individual Web service’s Web site.
Y
P
O
Configuring Settings to Use Web Services
Start EOS Utility on the computer, log in to CANON iMAGE GATEWAY,
then configure the camera’s settings to enable access to Web services.
For details, refer to the EOS Utility instruction manual (CD-ROM).
C
To use CANON iMAGE GATEWAY, you must be able to connect to the
Internet. (An account with an internet service provider is necessary,
browser software needs to be installed, and a line connection must be
completed.)
For information on browser (e.g. Microsoft Internet Explorer) versions
and settings required to access CANON iMAGE GATEWAY, check
CANON iMAGE GATEWAY.
Fees to connect to your provider and communication fees to access your
provider’s access point are charged separately.
104
Preparation
The general procedure for sending images to a Web service is as follows.
1
Prepare a computer on which EOS Utility has been
installed.
Use the software CD-ROM provided with the camera to install EOS
Utility.
2 Access Canon Web site from the computer and sign up
as a CANON iMAGE GATEWAY member (free of charge).
If you are already a member, proceed to step 3.
3 Connect the camera and computer with an interface
cable.
Before connection, set [53: Wi-Fi] to [Disable].
4 Start EOS Utility on the computer, log in to CANON
Y
P
O
iMAGE GATEWAY, then configure the camera’s settings
to enable access to Web services.
For details, refer to the EOS Utility instruction manual (CD-ROM).
C
5 Connect to the wireless LAN access point from the camera
(p.106).
Disconnect the interface cable in advance.
6 Send images to a Web service registered on the camera
(p.120).
You can share images with your family and friends by sending
images from the camera to a Web service registered on the camera
or by sending links to the online albums.
Information about countries and areas where CANON iMAGE
GATEWAY service is provided is available at Canon’s Web site
(http://canon.com/cig).
When the camera is connected to a computer as described in “Remote
Operation Using EOS Utility” (p.93), settings can be configured without
using any interface cable.
The camera’s Wi-Fi functions are compatible with the following Web
services (as of August 2013):
CANON iMAGE GATEWAY, Facebook, Twitter, YouTube, Flickr, and Email.
105
Checking the Type of Access Point
When Wi-Fi Protected Setup (WPS) is supported
• p.107: Easy Connection via WPS (PBC Mode)
• p.111: Easy Connection via WPS (PIN Mode)
When WPS is not supported
• p.115: Manual Connection by Searching Networks
If you do not know if the access point you use is WPS-compatible, refer
to the access point instruction manual or other documentation.
C
Y
P
O
When connecting to a network that has a network administrator, ask the
administrator about the detailed setting procedures.
If the network you use filters by MAC address, register the MAC address of
the camera at the access point. The MAC address can be checked on the
[General sett.] screen (p.149).
106
Easy Connection via WPS (PBC Mode)
This is a connection mode available when using an access point
compatible with Wi-Fi Protected Setup (WPS). In pushbutton
connection mode (PBC mode), the camera and the access point can be
connected simply by pressing the WPS button on the access point.
Note that if multiple access points are active in the surrounding area, it
may be more difficult to establish a connection. In this case, try using
[WPS (PIN mode)] to establish a connection.
Check the position of the WPS button on the access point in advance.
It may take approx. one minute to establish a connection.
If stealth functions of the access point are enabled, connection
may be disabled. Deactivate stealth functions.
1
Select [Wi-Fi function].
Under the [53] tab, set [Wi-Fi] to
[Enable], then select [Wi-Fi
function].
Y
P
2O
C
Select [w].
Select [w] (Upload to Web service)
and press <0>.
107
Easy Connection via WPS (PBC Mode)
a Web service.
3 Select
Select a Web service to connect to,
then press <0>.
The contents and ordering of the list of items
displayed will vary depending on settings.
The Web service to connect to can be
changed later (p.126).
X When the [Send to] screen (p.125) is
displayed, select a destination and go
to step 4.
[WPS (PBC mode)].
4 Select
Press the <V> key to select [WPS
(PBC mode)], then press <0>.
Select [OK] and press <0> to go to
the next screen.
C
5
Y
P
O
Connect to the access point.
Press the access point’s WPS button.
For details about where the button is
located and how long to press it, refer to
the access point’s instruction manual.
Select [OK] and press <0> to
establish a connection with the
access point.
X When a connection with the access
point is established, the [IP address
set.] screen is displayed.
the IP address.
6 SetPress
the <V> key to select how the
IP address should be set, then press
<0>.
108
Easy Connection via WPS (PBC Mode)
[Auto setting]
Configures the settings available in [Manual setting] automatically.
However, this option can only be used in environments using DHCP
servers ,or access points or routers with DHCP server functionality,
such that IP addresses and related settings are assigned and
configured automatically.
Select [OK] and press <0> to go to the next screen.
If an error is displayed even though the IP address and related
settings is set to be automatically assigned and configured, select
[Manual setting].
[Manual setting]
If [Auto setting] results in an error, enter the IP address manually.
Enter the IP address assigned to the camera when prompted for the IP
address.
Select [OK] and then select an item on the screen displayed. When
finished, press <0>.
When entering numbers, turn the <6>
dial to move the input position in the
upper area and turn the <5> dial to
select the number. Press <0> to enter
the selected number. When you have
finished entering information, press the
<M> button. A confirmation screen
is not displayed.
When you have completed setting all
items, select [OK] and press <0> to go to the next screen.
If you are not sure what to enter, see “Checking Network Settings”
(p.166), or ask the network administrator or another person
knowledgeable about the network.
C
Y
P
O
109
Easy Connection via WPS (PBC Mode)
further settings.
7 Perform
To finish settings in this stage, press
the <V> key to select [OK], then
press <0> to go to step 8.
To change the name of the settings,
select [Settings name] and press
<0>.
X The virtual keyboard is displayed
(p.14). Up to 30 characters can be
entered for the name of the settings.
the settings.
8 Save
Select [OK] and press <0> to save
Y
P
O
the settings.
X Images on the card are displayed.
C
images to send.
9 Select
Select and send the images. For
information on how to send images,
see page 120.
The settings for networking with Web services are now complete.
110
Easy Connection via WPS (PIN Mode)
This is a connection mode available when using an access point
compatible with Wi-Fi Protected Setup (WPS). In PIN code connection
mode (PIN mode), an 8-digit identification number specified on the
camera is set at the access point to establish a connection.
Even if there are multiple access points active in the surrounding area,
a relatively reliable connection can be established using this shared
identification number.
It may take approx. one minute to establish a connection.
If stealth functions of the access point are enabled, connection
may be disabled. Deactivate stealth functions.
1
Select [Wi-Fi function].
Under the [53] tab, set [Wi-Fi] to
[Enable], then select [Wi-Fi
function].
Y
P
2O
C
Select [w].
Select [w] (Upload to Web service)
and press <0>.
a Web service.
3 Select
Select a Web service to connect to
and press <0>.
The contents and ordering of the list
of items displayed will vary depending
on settings.
The Web service to connect to can be
changed later (p.126).
X When the [Send to] screen (p.125) is
displayed, select a destination and go
to step 4.
111
Easy Connection via WPS (PIN Mode)
[WPS (PIN mode)].
4 Select
Press the <V> key to select [WPS
(PIN mode)], then press <0>.
Select [OK] and press <0> to go to
the next screen.
the PIN code at the
5 Specify
access point.
At the access point, specify the 8-digit
PIN code displayed on the camera’s
LCD monitor.
For instructions on setting PIN codes
at the access point, refer to the
access point’s instruction manual.
After the PIN code is specified, select
[OK] and press <0>.
C
Y
P
O
to the access point.
6 Connect
Select [OK] and press <0> to
establish a connection with the
access point.
X When a connection with the access
point is established, the [IP address
set.] screen is displayed.
the IP address.
7 SetPress
the <V> key to select how the
IP address should be set, then press
<0>.
112
Easy Connection via WPS (PIN Mode)
[Auto setting]
Configures the settings available in [Manual setting] automatically.
However, this option can only be used in environments using DHCP
servers, or access points or routers with DHCP server functionality,
such that IP addresses and related settings are assigned and
configured automatically.
Select [OK] and press <0> to go to the next screen.
If an error is displayed even though the IP address and related
settings is set to be automatically assigned and configured, select
[Manual setting].
[Manual setting]
If [Auto setting] results in an error, enter the IP address manually.
Enter the IP address assigned to the camera when prompted for the IP
address.
Select [OK] and then select an item on the screen displayed. When
finished, press <0>.
When entering numbers, turn the <6>
dial to move the input position in the
upper area and turn the <5> dial to
select the number. Press <0> to enter
the selected number. When you have
finished entering information, press the
<M> button. A confirmation screen
is not displayed.
When you have completed setting all
items, select [OK] and press <0> to go to the next screen.
If you are not sure what to enter, see “Checking Network Settings”
(p.166), or ask the network administrator or another person
knowledgeable about the network.
C
Y
P
O
113
Easy Connection via WPS (PIN Mode)
further settings.
8 Perform
To finish settings in this stage, press
the <V> key to select [OK], then
press <0> to go to step 9.
To change the name of the settings,
select [Settings name] and press
<0>.
X The virtual keyboard is displayed
(p.14). Up to 30 characters can be
entered for the name of the settings.
the settings.
9 Save
Select [OK] and press <0> to save
Y
P
O
the settings.
X Images on the card are displayed.
C
images to send.
10 Select
Select and send the images. For
information on how to send images,
see page 120.
The settings for networking with Web services are now complete.
114
Manual Connection by Searching Networks
Selecting the Wireless Network
When [Find network] is selected, a list of active access points nearby
is displayed, accompanied by information about them. Select the SSID
(or ESS-ID) of the access point to connect to.
1
Select [Wi-Fi function].
Under the [53] tab, set [Wi-Fi] to
[Enable], then select [Wi-Fi
function].
[w].
2 Select
Select [w] (Upload to Web service)
Y
P
O
and press <0>.
C3
Select a Web service.
Select a Web service to connect to
and press <0>.
The contents and ordering of the list
of items displayed will vary depending
on settings.
The Web service to connect to can be
changed later (p.126).
When the [Send to] screen (p.125) is
displayed, select a destination and go
to step 4.
115
Manual Connection by Searching Networks
[Find network].
4 Select
Press the <V> key to select [Find
network], then press <0>.
Select [OK] and press <0> to go to
the next screen.
(1)
(2) (3)
(4)
an access point.
5 Select
Press <0> to enable the selection of
an access point.
Press the <V> key to select an
access point, then press <0>.
Select [OK] and press <0> to go to
the next screen (p.117).
Y
P
O
(1) Indicates that the device is in infrastructure mode
(2) An icon is displayed if the access point is encrypted
(3) First characters of the SSID
(4) Channel used
C
Access Point Encryption
This camera supports the following options for [Authentication] and
[Encryption settings]. Therefore, the encryption used by the access
point should be one of the following.
[Authentication]: Open system, Shared key, WPA-PSK, or WPA2PSK
[Encryption settings]: WEP, TKIP, or AES
[Enter connection] and [Search again]
To configure settings for the access point manually, select [Enter
connection] and press <0>. Enter the SSID using the virtual
keyboard and then configure settings following the instructions
displayed.
To search for access points again, select [Search again] and press
<0>.
116
Manual Connection by Searching Networks
Entering the Wireless LAN Encryption Key
Go to the next page when the [IP address set.] screen is displayed.
Set the encryption key specified for the access point. For details on the
specified encryption key, refer to the access point’s instruction manual.
Note that the screens displayed in steps 1 to 3 below vary depending on
the authentication and encryption specified for the access point.
1
2
C
3
The [Key index] screen is displayed
only if WEP encryption is used by the
access point.
Press the <V> key to select the key
index number specified for the access
point, then press <0>.
Select [OK] and press <0> to go to
the next screen.
Y
P
O
Press the <V> key to select the
format and the number of characters
used for the key, then press <0>.
Select [OK] and press <0> to go to
the next screen.
Enter the encryption key using the
virtual keyboard (p.14).
X The [IP address set.] screen (p.118)
will be displayed.
117
Manual Connection by Searching Networks
Setting the IP Address
Press the <V> key to select how the
IP address should be set, then press
<0>.
[Auto setting]
Configures the settings available in [Manual setting] automatically.
However, this option can only be used in environments using DHCP
servers, or access points or routers with DHCP server functionality,
such that IP addresses and related settings are assigned and
configured automatically.
Select [OK] and press <0> to go to the next screen (p.119).
If an error is displayed even though the IP address and related
settings is set to be automatically assigned and configured, select
[Manual setting].
[Manual setting]
C
Y
P
O
If [Auto setting] results in an error, enter the IP address manually.
Enter the IP address assigned to the camera when prompted for the IP
address.
Select [OK] and then select an item on the screen displayed. When
finished, press <0>.
When entering numbers, turn the <6>
dial to move the input position in the
upper area and turn the <5> dial to
select the number. Press <0> to enter
the selected number. When you have
finished entering information, press the
<M> button. A confirmation screen
is not displayed.
When you have completed setting all items, select [OK] and press
<0> to go to the next screen (p.119).
118
Manual Connection by Searching Networks
If you are not sure what to enter, see “Checking Network Settings”
(p.166), or ask the network administrator or another person
knowledgeable about the network.
Connecting to a Web Service
1
Perform further settings.
To finish settings in this stage, press
the <V> key to select [OK], then
press <0> to go to step 2.
To change the name of the settings,
select [Settings name] and press
<0>.
X The virtual keyboard is displayed
(p.14). Up to 30 characters can be
entered for the name of the settings.
C2
Y
P
O
Save the settings.
Select [OK] and press <0> to save
the settings.
X Images on the card are displayed.
images to send.
3 Select
Select and send the images. For
information on how to send images,
see page 120.
The settings for networking with Web services are now complete.
119
Sending Images to a Web Service
You can share movies and still photos you shot by sending them to a Web
service registered on the camera such as CANON iMAGE GATEWAY.
Sent images are saved in an online album on CANON iMAGE
GATEWAY and a link to the album is sent to each Web service. It is also
possible to send images to Web services directly depending on the
selected Web service and settings.
Sending Images One by One
Selected images are sent one by one.
1
Select an image to send.
Press the <U> key to select an
image to send, then press <0>.
You can also press the <I>
button to select an image in the index
display. To return to the single-image
display, press the <u> button.
C
Y
P
O
[Send img shown].
2 Select
To select a size at which to send the
image, select [Resize image] and
press <0>.
Press the <U> key to select [Send
img shown], then press <0>.
X The transfer progress screen is
displayed.
On the screen to complete the
process for sending the image, select
[OK] and press <0> to terminate the
connection.
A send error message may not be displayed in the following cases, even
when sending fails due to there being no space on the Web server that the
image was sent to:
• When the image has been reduced in size and sent
• When the image has been sent directly to a Web service other than
CANON iMAGE GATEWAY
120
Sending Images to a Web Service
A [Terms of use] screen is displayed
when sending images to certain Web
services. Thoroughly read the terms
of use, press the <U> key to select
[I Agree], then press <0>.
The screen can be scrolled up and
down by pressing the <V> key.
C
Y
P
O
If playback or shooting operation is started during the connection, the
connection will be terminated.
When accessing CANON iMAGE GATEWAY from a computer, you can
check the uploading history to registered Web services.
121
Sending Images to a Web Service
Sending Selected Images
Multiple images can be selected and sent.
1
Press <0>.
[Send selected].
2 Select
To select a size at which to send the
images, select [Resize image] and
press <0>.
Press the <U> key to select [Send
selected], then press <0>.
Y
P
O
the images to send.
3 Select
Press the <U> key to select
C
images to send, then press <0>.
X <X> is displayed on the upper left of
the images to send.
You can also press the <I>
button to select an image on the
three-image display. To return to the
single-image display, press the <u>
button.
After selecting the images to send,
press the <Q> button.
122
Sending Images to a Web Service
the image size.
4 Reduce
Set it if necessary.
For the setting procedures, see the
next page.
When YouTube is selected as the
destination, [Resize images to send]
is not displayed.
the images.
5 Send
Press the <V> key to select [Send],
then press <0>.
X The transfer progress screen is
C
displayed.
On the screen to complete the
process for sending images, select
[OK] and press <0> to terminate the
connection.
A [Terms of use] screen is displayed
when sending images to certain Web
services. Thoroughly read the terms
of use, press the <U> key to select
[I Agree], then press <0>.
The screen can be scrolled up and
down by pressing the <V> key.
Y
P
O
When sending a large number of images or large files, make sure that the
battery is adequately charged so it does not run out during the process.
If playback or shooting operation is started during the connection, the
connection will be terminated.
You can select up to 50 files at a time. Also, you can select up to 10 files
at a time to YouTube.
To confirm the limits for file size and movie playback time, check the
destination Web site.
When accessing CANON iMAGE GATEWAY from a computer, you can
check the upload history for registered Web services.
The file size (total size) is based on the file sizes before resizing the images.
123
Sending Images to a Web Service
Reducing the Size of the Image to Send
When [Send selected] is selected, the confirmation screen for sending
images also lets you select the size at which to send them.
1
Select [Resize images to send].
On the confirmation screen for
sending images, press the <V> key
to select [Resize images to send],
then press <0>.
the image size.
2 Select
Press the <V> key to select an
image size, then press <0>.
C
Y
P
O
the images.
3 Send
Press the <V> key to select [Send],
then press <0> to send the images.
All images to be sent at the same time are resized except those that are
already smaller than the selected image size.
Movies cannot be resized.
[Resize:S2] and [Resize:S3] are enabled only for still photos shot with
the EOS 70D. Images shot with other cameras are sent without resizing.
124
Sending Images to a Web Service
Selecting a Destination
You can send links to posted images to registered destinations.
To register Email destinations and settings for sending Emails, you
must use a computer. For more information, refer to the EOS Utility
Instruction Manual (CD-ROM).
When [
] (Email) is selected on the
[Upload to Web service] screen, the
[Send to] screen is displayed.
Select the destination from the list of
registered destinations and press
<0>.
The procedure for sending images is
the same as the procedure for
sending images to other Web
services.
C
Y
P
O
125
Reconnecting
The camera can reconnect to a Web service for which connection
settings have been registered. The connection to the access point only
has to be established once. You do not need to establish a new
connection for each Web service.
1
Select [Wi-Fi function].
Under the [53] tab, set [Wi-Fi] to
[Enable], then select [Wi-Fi
function].
[w].
2 Select
Select [w] (Upload to Web service)
and press <0>.
C
Y
P
O
a Web service.
3 Select
Select a Web service and press
<0>.
X When the [Send to] screen (p.125) is
displayed, select a destination and go
to step 4.
a connection.
4 Establish
Select [Connect] and press <0>.
On the confirmation screen, select [OK].
X The camera will reconnect to the Web
service.
When settings for multiple connection
destinations are registered, select
[Choose set.], select the connection
destination, then connect to the
destination.
126
Registering Multiple Connection Settings
You can register up to three Web service connection settings.
1
Select [Wi-Fi function].
Under the [53] tab, set [Wi-Fi] to
[Enable], then select [Wi-Fi
function].
[w].
2 Select
Select [w] (Upload to Web service)
and press <0>.
Y
P
O
a Web service.
3 Select
Select a Web service and press
C
<0>.
X When the [Send to] screen (p.125) is
displayed, select a destination and go
to step 4.
[Choose set.].
4 Select
Select [Choose set.] and press
<0>.
127
Registering Multiple Connection Settings
[Unspecified].
5 Select
Select [Unspecified] and press
<0>.
X The connection settings screen is
displayed. Follow the procedures
displayed to complete the connection
settings.
C
128
Y
P
O
MEMO
C
Y
P
O
129
MEMO
C
130
Y
P
O
Viewing Images Using
a Media Player
Y
P
O
Images on a card in the camera can be viewed on a TV
set via a wireless LAN.
C
This function requires a DLNA*-compatible TV set,
game machine, smartphone, or other media player. In
this manual, the term “media player” is used to refer to
any such device.
* DLNA: Digital Living Network Alliance
These instructions should be followed only after the
DLNA-compatible TV set or other device used is
connected to an access point. For information about
settings and configuration, refer to the documentation
provided with each device or contact the manufacturer.
131
Configuring Media Player Communication Settings
These instructions are continued from Chapter 5.
1
Perform further settings.
To finish settings in this stage, press
the <V> key to select [OK], then
press <0> to go to step 2.
To change the name of the settings,
select [Settings name] and press
<0>.
X The virtual keyboard is displayed
(p.14). Up to 30 characters can be
entered for the name of the settings.
Y
P
O
the settings.
2 Save
Select [OK] and press <0> to save
the settings.
X The [
Connection] screen is
displayed.
C
To return to the menu, press the
<M> button.
The settings for networking with the media player are now complete.
132
Displaying Images on a TV set
Images on the card in the camera can be displayed on a TV set using a
media player. Note that RAW images and movies cannot be displayed.
The following operations must be performed on the media player. For
details, refer to the media player’s instruction manual.
1
Display the media player settings
screen on your TV set.
Using the media player functions,
display the <
EOS 70D> (media
player) icon on the TV set.
A different icon may be displayed
depending on the media player. In
that case, locate the icon labeled
EOS 70D.
EOS 70D
Y
P
O
Select the <
EOS 70D> icon on
2 the
media player.
C
Selecting the <
EOS 70D> icon
will display an icon of the card. After
you select this icon, you can select
folders and images.
Select an image to display it at a
larger size on the TV set. For details,
refer to the media player’s instruction
manual.
IMG_0001.JPG
04/24/2013
EOS 70D
SD
04/24/2013
100CANON
04/24/2013
1-100
04/24/2013
IMG_0002.JPG
IMG_0003.JPG
133
Displaying Images on a TV set
Terminating the Connection
1
Select [Exit].
If the screen on the left is not
displayed, select [Wi-Fi function]
under the [53] tab.
Select [Exit] and press <0>.
[OK].
2 Select
Press the <U> key to select [OK],
then press <0> to terminate the
connection.
C
Y
P
O
When the Live View image is displayed on the camera, or during HDR
mode, HDR Backlight Control shooting, Handheld Night Scene or Multi Shot
Noise Reduction shooting, images may not be played back properly on the
media player.
Information overlay and details displayed on the TV set vary depending
on the media player. Note that depending on the media player, image
information may not be displayed, or the vertical image may be played
back in horizontal orientation.
Icons with labels such as “1-100” contain images grouped by file number
in the selected folder (***CANON).
Date information shown for images is based on Exif information added to
the images.
Date information shown for cards or folders may be the current date set
on the camera, in some cases.
If the camera’s auto power off is activated while searching for a wireless
LAN connection, the wireless LAN function will turn off. Wireless LAN
connection is restored when the camera wakes up from auto power off.
134
Reconnecting
The camera can reconnect to a media player for which connection
settings have been registered.
1
Select [Wi-Fi function].
Under the [53] tab, set [Wi-Fi] to
[Enable], then select [Wi-Fi
function].
[
2 Select
Select [
].
] (View images on DLNA
devices) and press <0>.
Y
P
O
a connection.
3 Establish
Select [Connect] and press <0>.
C
On the confirmation screen, select
[OK].
X The camera will reconnect to the
media player.
When settings for multiple connection
destinations are registered, select
[Choose set.], select the connection
destination, then connect to the
destination.
135
Registering Multiple Connection Settings
You can register up to three media player connection settings.
1
Select [Wi-Fi function].
Under the [53] tab, set [Wi-Fi] to
[Enable], then select [Wi-Fi
function].
[
2 Select
Select [
].
] (View images on DLNA
devices) and press <0>.
Y
P
O
[Choose set.].
3 Select
Select [Choose set.] and press
<0>.
C
[Unspecified].
4 Select
Select [Unspecified] and press
<0>.
X The connection settings screen is
displayed. Follow the procedures
displayed to complete the connection
settings.
136
MEMO
C
Y
P
O
137
MEMO
C
138
Y
P
O
Using Quick Control to
Connect to a Wireless LAN
Y
P
O
Quick Control or Quick Control during playback lets you
connect to a wireless LAN using registered connection
destination settings.
C
Connection destination settings cannot be set using Quick Control.
Set connection destination settings from the menu screen.
139
Connecting from Quick Control
You can use Quick Control to access Wi-Fi functions for which
connection destination settings have been registered. Three functions
are available in Quick Control: [q] (Connect to smartphone), [D]
(Remote control (EOS Utility)), and [ ] (View images on DLNA
devices).
Set the Mode Dial to the Creative Zone before using these functions.
1
Select [
].
Press the <Q> button to display
Quick Control.
Select [
] (Wi-Fi function) and
press <0>.
This cannot be selected if [Wi-Fi]
under the [53] tab is set to [Disable].
X During connection, the screen on the
left is displayed. To change the
connection destination, select [OK],
press <0> to terminate the
connection, then configure settings.
C
Y
P
O
the item to connect to.
2 Select
Select the item to connect to and
press <0>.
Items for which connection
destination settings have not been
registered are grayed out.
a connection.
3 Establish
Select [Connect] and press <0>.
When settings for multiple connection
destinations are registered, select
[Choose set.], select the connection
destination, then connect to the
destination.
140
Connecting from a Playback Screen
You can also use Quick Control during playback to access Wi-Fi
functions for which connection destination settings have been
registered. From Quick Control during playback, two functions can be
used: [z] (Transfer images between cameras) and [w] (Upload to
Web service).
1
Press the <Q> button.
While an image is displayed, press
the <Q> button.
X Quick Control items will be displayed.
[k].
2 Select
Select [k] (Wi-Fi function) and press
Y
P
O
<0>.
This cannot be selected if [Wi-Fi]
under the [53] tab is set to [Disable].
C
X During connection, the screen on the
left is displayed. Select [OK], press
<0> to terminate the connection,
then configure settings.
141
Connecting from a Playback Screen
the item to connect to.
3 Select
Select the item to connect to and
press <0>.
Items for which connection
destination settings have not been
registered are grayed out.
X When you select [w] (Upload to Web
service), a screen to select a Web
service is displayed. Select the item
to connect to and press <0>.
X When the [Send to] screen (p.125) is
displayed, select a destination and go
to step 4.
Y
P
O
a connection.
4 Establish
Select [Connect] and press <0>.
X The images on the card are displayed
and the images to send can be
selected.
C
When settings for multiple connection
destinations are registered, select
[Choose set.], select the connection
destination, then connect to the
destination.
142
MEMO
C
Y
P
O
143
MEMO
C
144
Y
P
O
Managing Settings
C
Y
P
O
145
Checking or Changing Settings
Check the network settings as follows.
1
Select [Wi-Fi function].
Under the [53] tab, set [Wi-Fi] to
[Enable], then select [Wi-Fi
function].
the item to check settings
2 Select
for.
Press the <V> or <U> key to
select an item, then press <0>.
When you select [w], a screen to
select a Web service is displayed.
The same settings are displayed for
any item selected.
During Connection
C
Y
P
O
If [Wi-Fi function] is selected during
connection, the screen on the left is
displayed.
Select [Confirm set.] and press
<0> to display the settings.
146
Checking or Changing Settings
When the Connection Has Been Terminated
Select the connection destination,
select [Review/change settings],
then press <0>.
Select [Confirm set.] and press
<0> to display the settings.
C
Y
P
O
147
Checking or Changing Settings
Changing Settings
To change settings, select [Change
set.] on the [Review/change
settings] screen shown on page 147.
X A screen for setting connection is
displayed. Configure connection
settings again following the
procedures.
Changing Setting Names
To change the name of the settings,
select [Change settings name] on
the [Review/change settings]
screen shown on page 147.
X Enter the name of the settings using
the virtual keyboard (p.14).
C
148
Y
P
O
Clearing Wireless LAN Settings
All wireless LAN settings can be deleted by the procedure described
below. By deleting the wireless LAN settings, you can prevent them
from being exposed when you lend or give your camera to other people.
1
Select [Wi-Fi function].
Under the [53] tab, set [Wi-Fi] to
[Enable], then select [Wi-Fi
function].
the <B> button.
2 Press
X The general settings screen is
displayed.
Y
P
3O
C
Select [Clear Wi-Fi settings].
Press the <V> key to select [Clear
Wi-Fi settings], then press <0>.
[OK].
4 Select
Select [OK] and press <0>.
X Settings for [Wi-Fi function] are
cleared and the menu screen will
reappear.
Performing [54: Clear all camera settings] does not clear settings for
[Wi-Fi function].
149
MEMO
C
150
Y
P
O
Troubleshooting Guide
C
Y
P
O
Transfer speed in ad hoc mode may become extremely slow when
the camera is used with certain types of computer. For more
information, contact your dealer or nearest Canon Service Center.
151
Responding to Error Messages
When <k> or <l> on the LCD panel blinks, display the error
content following one of the procedures below. Then, eliminate the
cause of the error referring to the examples shown in this chapter.
Select [53: Wi-Fi function] 9 [General sett.] 9 [Error details],
then press <0>.
Select [53: Wi-Fi function] and press <0>.
Click the error number in the following chart to jump to the
corresponding page.
11 (p.153)
12 (p.153)
21 (p.153)
22 (p.154)
23 (p.155)
61 (p.156)
62 (p.156)
63 (p.157)
64 (p.157)
66 (p.158)
67 (p.158)
68 (p.158)
69 (p.159)
101 (p.159)
102 (p.159)
103 (p.160)
104 (p.160)
106 (p.160)
107 (p.160)
108 (p.161)
109 (p.161)
121 (p.161)
122 (p.161)
123 (p.161)
124 (p.161)
126 (p.162)
127 (p.162)
91 (p.159)
141 (p.162)
152
C
Y
P
O
65 (p.157)
105 (p.160)
125 (p.162)
Responding to Error Messages
11: Connection target not found
In the case of [q], is EOS Remote running?
X Establish a connection using EOS Remote (p.37, 78).
In the case of [l], is the power of the printer on?
X Turn on the printer.
In the case of [D], is the pairing software running?
X Start the pairing software and follow the instructions to re-establish
the connection (p.95).
Are the camera and the access point set to use the same
encryption key for authentication?
X This error occurs if the encryption keys do not match when the
authentication method for encryption is set to [Open system].
The setting is case-sensitive, so check upper- and lower-case
characters. Make sure that the correct encryption key for
authentication is entered on the camera (p.69, 117).
Y
P
O
12: Connection target not found
C
Is the power of the target device and access point on?
X Turn on the target device and access point.
21: No address assigned by DHCP server
What to check on the camera
On the camera, IP address is set to [Auto assign]. Is this the
correct setting?
X If no DHCP server is used, configure settings after setting the IP
address to [Manual setting] on the camera (p.59, 64, 70, 109, 113,
118).
What to check on the DHCP server
Is the power of the DHCP server on?
X Turn on the DHCP server.
Are there enough addresses for assignment by the DHCP server?
X Increase the number of addresses assigned by the DHCP server.
X Remove devices assigned addresses by the DHCP server from
the network to reduce the number of addresses in use.
153
Responding to Error Messages
Is the DHCP server working correctly?
X Check the DHCP server settings to make sure it is working
correctly as a DHCP server.
X If applicable, ask your network administrator to ensure the DHCP
server is available.
Responding to Error Messages 21 - 23
Also check the following points when responding to errors numbered 21 - 23.
Are the camera and the access point set to use the same encryption
key for authentication?
X This error occurs if the encryption keys do not match when the authentication
method for encryption is set to [Open system]. The setting is case-sensitive,
so check upper- and lower-case characters. Make sure that the correct
encryption key for authentication is entered on the camera (p.69, 117).
Y
P
O
22: No response from DNS server
What to check on the camera
On the camera, does the DNS server’s IP address setting
match the server’s actual address?
X Set the IP address to [Manual setting]. Then, on the camera, set
the IP address that matches the address of the DNS server used
(p.109, 113, 118, 166).
C
What to check on the DNS server
Is the power of the DNS server on?
X Turn on the DNS server.
Are the DNS server settings for IP addresses and the
corresponding names correct?
X On the DNS server, make sure IP addresses and the
corresponding names are entered correctly.
Is the DNS server working correctly?
X Check the DNS server settings to make sure the server is working
correctly as a DNS server.
X If applicable, ask your network administrator to ensure that the
DNS server is available.
154
Responding to Error Messages
What to check on the network as a whole
Does your network include a router or similar device that
serves as a gateway?
X If applicable, ask your network administrator for the network
gateway address and enter it on the camera (p.59, 64, 70, 109,
113, 118, 166).
X Make sure that the gateway address setting is correctly entered on
all network devices, including the camera.
23: Duplicate IP address
What to check on the camera
Is another device on the camera network using the same IP
address as the camera?
X Change the camera’s IP address to avoid using the same address
as another device on the network. Otherwise, change the IP
address of the device that has a duplicate address.
X If the camera’s IP address is set to [Manual setting] in network
environments using a DHCP server, change the setting to [Auto
setting] (p.59, 64, 70, 109, 113, 118).
C
Y
P
O
155
Responding to Error Messages
61: Selected SSID wireless LAN network not found
Are any obstacles blocking the line of sight between the
camera and the antenna of the access point?
X Move the antenna of the access point to a position clearly visible
from the point of view of the camera (p.164).
What to check on the camera
Does the SSID set on the camera match that of the access
point?
X Check the SSID at the access point, then set the same SSID on
the camera (p.68, 116).
What to check at the access point
Is the access point turned on?
X Turn on the power of the access point.
If filtering by MAC address is effective, is the MAC address of
the camera used registered at the access point?
X Register the MAC address of the camera used at the access point.
The MAC address can be checked on the [General sett.] screen
(p.149).
C
Y
P
O
62: No response from wireless LAN terminal
What to check on the wireless LAN terminal
Is there a wireless LAN terminal for ad hoc communication
nearby?
X Set up a wireless LAN terminal for ad hoc communication near the
camera.
156
Responding to Error Messages
63: Wireless LAN authentication failed
X
X
X
X
Are the camera and the access point set to use the same
authentication method?
The camera supports the following authentication methods: [Open
system], [Shared key], [WPA-PSK], and [WPA2-PSK] (p.68, 116).
When using an AirPort for communication in infrastructure mode,
[Open system] is not supported. Configure a [Shared key] on the
camera (p.68, 116).
Are the camera and the access point set to use the same
encryption key for authentication?
The setting is case-sensitive, so check upper- and lower-case
characters. Make sure that the correct encryption key for
authentication is entered on the camera and the access point
(p.69, 117).
If filtering by MAC address is effective, is the MAC address of
the camera used registered at the access point?
Register the MAC address at the camera used at the access point. The
MAC address can be checked on the [General sett.] screen (p.149).
C
Y
P
O
64: Cannot connect to wireless LAN terminal
Are the camera and the access point set to use the same
encryption method?
X The camera supports the following encryption methods: [WEP],
[TKIP], and [AES] (p.68, 116).
If filtering by MAC address is effective, is the MAC address of
the camera used registered at the access point?
X Register the MAC address of the camera used at the access point. The
MAC address can be checked on the [General sett.] screen (p.149).
65: Wireless LAN connection lost
Are any obstacles blocking the line of sight between the
camera and the antenna of the access point?
X Move the antenna of the access point to a position clearly visible
from the point of view of the camera (p.164).
157
Responding to Error Messages
The wireless LAN connection was lost, for some reason, and
the connection cannot be restored.
X The following are possible reasons: excessive access to the
access point from other device, a microwave oven or similar
appliance in use nearby (interfering with IEEE 802.11b/g/n (2.4
GHz band)), or influence of rain or high humidity (p.164).
66: Incorrect wireless LAN encryption key
Are the camera and the access point set to use the same
encryption key for authentication?
X The setting is case-sensitive, so check upper- and lower-case
characters. Make sure that the correct encryption key for
authentication is entered on the camera and the access point
(p.69, 117).
Y
P
O
67: Incorrect wireless LAN encryption method
Are the camera and the access point set to use the same
encryption method?
X The camera supports the following encryption methods: [WEP],
[TKIP], and [AES] (p.68, 116).
If filtering by MAC address is effective, is the MAC address of
the camera used registered at the access point?
X Register the MAC address of the camera used at the access point.
The MAC address can be checked on the [General sett.] screen
(p.149).
C
68: Cannot connect to wireless LAN terminal. Retry from
the beginning.
Did you hold down the access point’s WPS (Wi-Fi Protected
Setup) button for the specified period of time?
X Hold down the WPS button for the period of time instructed by the
access point’s instruction manual.
Are you trying to establish a connection near the access point?
X Try establishing the connection when both devices are within reach
of each other.
158
Responding to Error Messages
69: Multiple wireless LAN terminals have been found.
Cannot connect. Retry from the beginning.
Connection is in progress by other access points in Pushbutton
Connection mode (PBC mode) of Wi-Fi Protected Setup (WPS).
X Wait a while before trying to establish the connection, or try to
establish a connection in PIN code connection mode (PIN mode)
(p.62, 111).
91: Other error
A problem other than error number 11 to 69 occurred.
X Turn off and on the camera’s power switch.
101: Could not establish connection
Y
P
O
Has the procedure to establish a connection between
cameras been performed on the other camera as well?
X Perform the procedure to establish a connection between cameras
on the other camera as well.
X When reconnecting cameras for which connection settings have
been registered, perform the reconnection procedure on both
cameras.
Is connection being attempted by multiple cameras?
X The camera can be connected to only one camera at a time.
Confirm that no other camera is attempting to establish a
connection nearby and retry connection.
C
102: Could not send files
Does the card in the camera to receive data have sufficient space?
X Check the card in the camera to receive data. Replace the card or
make sufficient space available, then try sending the data to the
camera again.
Is the card in the camera to receive data locked?
X Check the card in the camera to receive data. Release the lock,
then try sending the data to the camera again.
159
Responding to Error Messages
Check if the folder number of the camera to receive data is
999 and the file number 9999.
X Folder or file names cannot be created automatically. Replace the
card in the camera to receive data, then try sending the data again.
Is the card working properly?
X Replace the card in the camera to receive data, then try sending
the data again.
103: Could not receive files
Is the camera to receive data ready to receive data?
X Check the battery of the camera to receive data and connection
status, then try sending the data again.
104: Could not receive files. Card full
Y
P
O
Does the card in the camera to receive data have sufficient space?
X Check the card in the camera to receive data. Replace the card or
make sufficient space available, then try sending the data again.
C
105: Could not receive files. Card’s write protect switch is
set to lock
Is the card in the camera to receive data locked?
X Check the card in the camera to receive data. Release the lock,
then try sending the data again.
106: Could not receive files. Folder and file number have
reached maximum value
Check if the folder number of the camera to receive data is
999 and the file number 9999.
X Folder or file names cannot be created automatically. Replace the
card in the camera to receive data, then try sending the data again.
107: Could not receive files. Card cannot be accessed
Is the card working properly?
X Replace the card in the camera to receive data, then try sending
the data again.
160
Responding to Error Messages
108: Disconnected
Has the target camera terminated the connection?
X Check the connection status and connect the cameras again.
109: An error has occurred
A problem other than those described in errors 101 through
108 occurred during the connection between cameras.
X Connect the cameras again.
121: Not enough free space on server
The target Web server does not have enough free space.
X Delete unnecessary images on the Web server, check the free
space on the Web server, then try sending the data again.
Y
P
O
122: Connect to a computer, and correct the settings for
the Web service with the provided software
Web service setting operation may be failed.
X Connect the camera and computer using an interface cable and
reconfigure Web service settings using EOS Utility (p.105).
C
123: Cannot log in to Web service. Connect to a computer
and correct the settings with the provided software.
Is the camera’s registration information or Web service
registered on the camera deleted on CANON iMAGE
GATEWAY?
X Connect the camera and computer using an interface cable and
reconfigure Web service settings using EOS Utility (p.105).
124: Invalid SSL certificate. Connect to a computer and
correct the settings with the provided software.
The root certificate has expired or is invalid.
X Connect the camera and computer using an interface cable and
reconfigure Web service settings using EOS Utility (p.105).
161
Responding to Error Messages
125: Check the network settings
Is the network connected?
X Check the connection status of the network.
126: Could not connect to server
CANON iMAGE GATEWAY is under maintenance or load is
concentrated temporarily.
X Try connecting to the Web service again later.
127: An error has occurred
A problem other than error 121 to 126 occurred during the
connection to the Web service.
X Try connecting to the Web service again.
Y
P
O
141: Printer is busy. Try connecting again.
Is the printer performing a printing process?
X Connect to the printer again after the printing process is finished.
C
Is another camera connected to the printer?
X Connect to the printer again after the connection between the
printer and the other camera has been terminated.
162
Troubleshooting Guide
If a problem occurs with the camera, first refer to this Troubleshooting
Guide. If this Troubleshooting Guide does not resolve the problem,
contact your dealer or nearest Canon Service Center.
A computer, printer, GPS receiver, or other device
cannot be used with a cable connection.
Set [53: Wi-Fi] to [Disable]. If [Wi-Fi] is set to [Enable], even
when the camera is connected to a computer, printer, GPS
receiver, or other device via an interface cable, the device cannot
be used (p.17).
[Wi-Fi] cannot be set to [Enable].
[53: Wi-Fi] cannot be set to [Enable] if the camera is connected to
a computer, printer, GPS receiver, or other device via an interface
cable (p.17).
If [Multiple exposure] is set to [Enable], multiple exposure
shooting is given priority and the Wi-Fi function cannot be used.
Even when [53: Wi-Fi] is set to [Enable], [53: Wi-Fi function] will
be grayed out and the function is not available.
C
Y
P
O
163
Wireless LAN Notes
If the transmission rate drops, the connection is lost, or other problems
occur when using the camera with a wireless LAN, try the following
corrective actions.
Access Point and Antenna Installation Location
When using indoors, install the device in the same room that you
are shooting.
Install the device higher than the camera.
Install the device where people or objects do not come between it
and the camera.
Install the device as close to the camera as possible. In particular,
note that during outdoor use in poor weather, rain may absorb
radio waves and disrupt the connection.
Nearby Electronic Devices
Y
P
O
If the transmission rate of a wireless LAN drops because of the
influence of the following electronic devices, stop using them or
establish a connection further away from them.
The camera communicates over wireless LANs via IEEE 802.11b/
g/n using radio waves in the 2.4 GHz band. For this reason, the
wireless LAN transmission rate may drop if there are microwave
ovens, cordless telephones, microphones, or similar devices
operating on the same frequency band nearby.
If a Wi-Fi device on the same frequency band as the camera is
used nearby, the transmission rate of the wireless LAN may drop.
C
Notes for Using Multiple Cameras
When connecting multiple cameras to one access point, make
sure that the cameras’ IP addresses are different.
When multiple cameras are connected to one access point, the
transmission rate drops.
When there are multiple IEEE 802.11b/g/n (2.4 GHz band) access
points, leave a gap of four channels between each wireless LAN
channel to reduce radio wave interference. For example, use
channels 1, 6, and 11, channels 2 and 7, or channels 3 and 8.
164
Wireless LAN Notes
Security
Wireless LAN radio waves can be easily intercepted. For this
reason, we recommend activating encrypted communication in the
access point settings.
Connecting with an Interface Cable
When [53: Wi-Fi] is set to [Enable], interface cable connection is
disabled. Set it to [Disable] and then connect an interface cable.
When the camera is connected to a computer, printer, or any other
device via an interface cable, settings for [Wi-Fi] cannot be
changed. Disconnect the interface cable before changing any
settings.
Using an Eye-Fi Card
Y
P
O
When [53: Wi-Fi] is set to [Enable], image transfer using an EyeFi card is disabled.
Movie Shooting
C
Movie shooting is disabled when [53: Wi-Fi] is set to [Enable].
165
Checking Network Settings
Windows
Click the Windows [Start] button 9 [All Programs] 9 [Accessories]
9 [Command Prompt]. Type ipconfig/all and press the <Enter> key.
The IP address assigned to the computer is displayed, as well as the
subnet mask, gateway, and DNS server information.
To avoid using the same IP address for the computer and other devices
on the network, change the rightmost number when configuring the IP
address assigned to the camera in the processes described in pages
59, 64, 70, 109, 113, and 118.
Example: 192.168.1.10
Macintosh
Y
P
O
In Mac OS X, open the [Terminal] application, enter ifconfig -a, and
press the <Return> key. The IP address assigned to the computer is
indicated in the [en0] item by [inet], in the format “***.***.***.***”.
To avoid using the same IP address for the computer and other devices
on the network, change the rightmost number when configuring the IP
address assigned to the camera in the processes described in pages
59, 64, 70, 109, 113, and 118.
C
* For information about the [Terminal] application, refer to the Mac OS X help.
Example: 192.168.1.10
166
MEMO
C
Y
P
O
167
MEMO
C
168
Y
P
O
Reference
C
Y
P
O
169
Specifications
9Wireless LAN
Standards compliance:
Transmission method:
Transmission range:
Transmission frequency
(central frequency):
Connection method:
Security:
9Network Functions
Transfer images
between cameras:
IEEE 802.11b/g/n
DS-SS modulation (IEEE 802.11b)
OFDM modulation (IEEE 802.11g/n)
Approx. 30 m/98.4 ft.
* With no obstructions between the transmitting and
receiving antennas and no radio interference
* With a large, high-performance antenna attached to
the wireless LAN access point
Frequency
Channels
2412 to 2462 MHz
1 to 11 ch
Infrastructure mode*, ad hoc mode, camera access
point mode
* Wi-Fi Protected Setup supported
Authentication method: Open system, Shared key,
WPA-PSK, WPA2-PSK
Encryption: WEP, TKIP, AES
C
Y
P
O
Transferring one image
Transferring selected images
Transferring resized images
Connection to smartphones: Images can be viewed, controlled, and received using
a smartphone.
Remote control of the camera using a smartphone
Remote operation
Remote control functions and image viewing functions
using EOS Utility:
of EOS Utility can be used via a wireless LAN.
Print from Wi-Fi printers: Images to be printed can be sent to a printer
supporting Wi-Fi.
Send images to
Images in the camera or links to images can be sent to
a Web service:
registered Web services.
View images using
Images can be viewed using a DLNA-compatible
a media player:
media player.
All preceding specifications are based on Canon testing standards.
170
Index
A
M
Access point encryption ..........68, 116
MAC address........ 56, 76, 94, 95, 106
Android......................................32, 55
Media player................................. 131
Auto power off.................................15
C
N
Nickname ....................................... 12
Cable...............................................17
P
Camera access point mode ......33, 46
PictBridge ................................. 45, 87
CANON iMAGE GATEWAY ..........104
PIN code connection mode .... 62, 111
Changing setting names .........28, 148
Printing ..................................... 45, 87
Changing settings .........................148
Pushbutton connection
Checking settings..........................146
mode ...................................... 57, 107
Y
P
O
Clearing wireless LAN settings .....149
Connecting to a smartphone.....31, 75
D
C
DLNA ........................................3, 131
E
Q
Quick Control................................ 139
R
Reconnecting ........ 26, 39, 51, 80, 91,
99, 126, 135
Email .............................................125
Reducing the image size ........ 25, 124
EOS Remote.................32, 37, 55, 78
Registering devices ..... 27, 43, 52, 84,
92, 100, 127,
EOS Utility.......................................93
136
Eye-Fi card......................................17
I
Infrastructure mode.............58, 62, 67
iOS ............................................32, 55
IP address...58, 63, 70, 108, 112, 118
K
Remote operation........................... 93
Remote shooting ................ 37, 78, 98
S
Sending images...................... 22, 120
Stealth functions ....... 57, 62, 107, 111
Keyboard.........................................14
171
Index
T
Touch control ..................................17
Transferring images between
cameras ..........................................19
Troubleshooting Guide .................151
V
Viewable images.......................40, 81
Viewing images.............................131
W
Wi-Fi printer ..............................45, 87
Wireless LAN access point .....56, 106
Wireless LAN notes ......................164
WPS
C
(Wi-Fi Protected Setup) ..........56, 106
172
Y
P
O
MEMO
C
Y
P
O
CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan
U.S.A.
CANON U.S.A. INC.
http://www.usa.canon.com/eos
http://www.usa.canon.com/support
For all inquires concerning this product, call toll free in the U.S.
1-800-OK-CANON
CANADA
CANON CANADA INC. HEADQUARTERS
6390 Dixie Road, Mississauga, Ontario L5T 1P7, Canada
CANON CANADA INC. MONTREAL BRANCH
5990, Côte-de-Liesse, Montréal Québec H4T 1V7, Canada
CANON CANADA INC. CALGARY OFFICE
2828, 16th Street, N.E. Calgary, Alberta T2E 7K7, Canada
For all inquiries concerning this product, call toll free in Canada
1-800-OK-CANON
EUROPE,
AFRICA &
MIDDLE EAST
CANON EUROPA N.V.
Bovenkerkerweg 59, 1185 XB Amstelveen, The Netherlands
CANON FRANCE S.A.S.
17, Quai du Président Paul Doumer, 92414 Courbevoie Cedex, France
CANON UK LTD.
Woodhatch Reigate, Surrey RH2 8BF, United Kingdom
CANON DEUTSCHLAND GmbH
Europark Fichtenhain A10, 47807 Krefeld, Germany
CANON ITALIA S.p.A.
Via Milano 8, 20097 San Donato Milanese, (MI), Italy
CANON Schweiz A.G.
Industriestrasse 12, 8305 Dietlikon, Switzerland
Canon GmbH
Zetschegasse 11, A-1230 Vienna, Austria
CANON España, S.A.
Av. De Europa, 6 Alcobendas 28108 Madrid, Spain
CANON Portugal S.A.
Rua Alfredo da Silva,14 Alfragide 2610-016 Amadora, Portugal
C
Y
P
O
CENTRAL &
SOUTH AMERICA
CANON LATIN AMERICA, INC.
http://www.cla.canon.com
ASIA
CANON (China) Co., LTD.
15F Jinbao Building No.89 Jinbao Street, Dongcheng District, Beijing 100005, China
CANON HONGKONG CO., LTD.
19/F., The Metropolis Tower, 10 Metropolis Drive, Hunghom, Kowloon, Hong Kong
CANON SINGAPORE PTE. LTD.
1 Harbour Front Avenue, #04-01 Keppel Bay Tower, Singapore 098632
CANON KOREA CONSUMER IMAGING INC.
Canon BS Tower 5F, #168-12 Samseong-dong, Gangnam-gu, Seoul, Korea
OCEANIA
CANON AUSTRALIA PTY. LTD.
1 Thomas Holt Drive, North Ryde, Sydney N.S.W. 2113, Australia
CANON NEW ZEALAND LTD.
Akoranga Business Park, Akoranga Drive, Northcote, Auckland, New Zealand
JAPAN
CANON MARKETING JAPAN INC.
16-6, Kohnan 2-chome, Minato-ku, Tokyo 108-8011, Japan
CPY-E059-001
© CANON INC. 2013