DVD-H1080
DVD-H1080R
DVD-H1080W
DVD Player
user manual
imagine the possibilities
Thanks you for purchasing this Samsung product.
To receive more complete service, please register
your product at
www.samsung.com/global/register
AK68-01754K(02)
precautions
1. Setting up
- Refer to the identification label located
on the rear of your player for its proper operating voltage.
- Install your player in a cabinet with adequate ventilation holes. (7~10cm) Do
not block ventilation holes on any of the
components for air circulation.
- Do not push the disc tray in by hand.
- Do not stack components.
- Be sure to turn all components off before
moving the player.
- Before connecting other components to this
player, be sure to turn them off.
- Be sure to remove the disc and turn off the
player after use, especially if you are not
going to use it for a long time.
- The mains plug is used as a disconnect
device and shall stay readily operable at
any time.
2. For your safety
- This product utilizes a laser. Use of controls or adjustments or performance of procedures other than those specified
herein may result in hazardous radiation
exposure.
- Do not open covers and do not repair yourself. Refer servicing to qualified personal.
3. Caution
- Your player is not intended for industrial
use but for domestic purposes. Use of this product is for personal use only.
- Apparatus shall not be exposed to dripping
or splashing and no objects filled with liquids,
such as vases, should be placed on the
apparatus.
- Exterior influences such as lightning and
static electricity can affect normal operation
of this player. If this occurs, turn the player
off and on again with the POWER button,
or disconnect and then reconnect the AC
power cord to the AC power outlet. The
player will operate normally.
_ precautions
- When condensation forms inside
the player due to sharp changes in temperature, the player may not operate
correctly. If this occurs, leave the player
at room temperature until the inside of the
player becomes dry and operational.
4. Disc
- Do not clean disc using record-cleaning
sprays, benzene, thinner, or other volatile
solvents that may cause damage to the disc
surface.
- Do not touch the disc’s signal surface. Hold
by the edges or by one edge and the hole
in the center.
- Wipe the dirt away gently; never wipe a
cloth back and forth over the disc.
5. Environmental info
- The battery used in this product contains chemicals that are harmful to the environ
ment.
- So, dispose of batteries in the proper man ner, according to federal, state, and local regulations.
The product unit accompanying this user manual
is licensed under certain intellectual property rights
of certain third parties. This license is limited to
private non-commercial use by end-user consumers for licensed contents. No rights are granted for commercial use. The license does not cover any
product unit other than this product unit and the
license does not extend to any unlicensed product
unit or process conforming to ISO/OUR 11172-3 or
ISO/OUR 13818-3 used or sold in combination with
this product unit. The license only covers the use of
this product unit to encode and/or decode audio files
conforming to the ISO/OUR 11172-3 or ISO/OUR
13818-3. No rights are granted under this license for
product features or functions that do not conform to
the ISO/OUR 11172-3 or ISO/OUR 13818-3.
CAUTION: USE OF ANY CONTROLS, ADJUSTMENTS, OR PROCEDURES OTHER
THAN SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
before you start table of content
Accessories
Remote Control
User’s Manual
Batteries for Remote
Control (AAA Size)
Video/Audio
Cable
The accessories which are not supplied are:
• Scart Cable
• Component Cable
• Coaxial Cable.
• HDMI-HDMI Cable.
• HDMI-DVI Cable.
Install Batteries in the Remote control
1. Open the battery cover on the back of the remote control.
2. Insert two AAA batteries.
Make sure that the
polarities (+ and -) are aligned correctly.
3. Replace the battery cover.
If remote control doesn’t operate
properly:
- Check the polarity + - of the battery (Dry-Cell)
- Check if the battery is drained.
- Check if remote control sensor is blocked by
obstacles.
- Check if there is any fluorescent lighting nearby.
- The rechargeable battery incorporated in this
product is not user replaceable.
- For information on its replacement, please contact your service provider.
Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Setup
General Features . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Disc Type and Characteristics . . . . . . . . . . . . . . . . 5
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Tour of the Remote Control. . . . . . . . . . . . . . . . . . . 7
Connections
Choosing a Connection . . . . . . . . . . . . . . . . . . . . . 8
Basic Functions
Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Using the Search and Skip Functions . . . . . . . . . 16
Using the Display Function . . . . . . . . . . . . . . . . . 16
Using the Disc and Title Menu . . . . . . . . . . . . . . . 17
Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Slow Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Advanced Functions
Adjusting the Aspect Ratio (EZ View). . . . . . . . . . 18
Selecting the Audio Language . . . . . . . . . . . . . . . 18
Selecting the Subtitle Language. . . . . . . . . . . . . . 19
Changing the Camera Angle. . . . . . . . . . . . . . . . . 19
Using the Bookmark Function. . . . . . . . . . . . . . . . 20
Using the Zoom Function . . . . . . . . . . . . . . . . . . . 20
Clips Menu for MP3/WMA/JPEG/MPEG4/
CD Audio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Folder Selection . . . . . . . . . . . . . . . . . . . . . . . . . . 21
MP3/WMA/CD Audio Playback. . . . . . . . . . . . . . . 21
MPEG4 Playback . . . . . . . . . . . . . . . . . . . . . . . . . 22
Playing media files Using the USB
Host Feature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
CD Ripping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Picture CD Playback. . . . . . . . . . . . . . . . . . . . . . . 25
Picture CD Playback for HD JPEG. . . . . . . . . . . . 26
Changing Setup Menu
Using the Setup Menu. . . . . . . . . . . . . . . . . . . . . . 27
Setting Up the Language Features. . . . . . . . . . . . 27
Setting Up the Audio Options. . . . . . . . . . . . . . . . 28
Setting Up the Display Options. . . . . . . . . . . . . . . 29
Setting Up the Parental Control . . . . . . . . . . . . . . 30
Setting Up the HDMI. . . . . . . . . . . . . . . . . . . . . . . 32
Reference
Firmware Upgrade. . . . . . . . . . . . . . . . . . . . . . . . . 35
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
English _
setup
General Features
Excellent Sound
Dolby Digital, a technology developed by Dolby
Laboratories, provides crystal clear sound reproduction.
Screen
Both regular and widescreen(16:9) pictures can be
viewed.
Slow Motion
An important scene can be viewed in slow motion.
1080p Playback
This player upconverts regular DVDs for playback
on 1080p TVs.
Parental Control (DVD)
The parental control allows users to set the level
necessary to prohibit children from viewing harmful
movies such as those with violence, adult subject
matter, etc.
Various On-Screen Menu Functions
You can select various languages (Audio/Subtitle)
and screen angles while enjoying movies.
Progressive Scan
Progressive scanning creates an improved picture
with double the scan lines of a conventional interlaced picture.
EZ VIEW (DVD)
Easy View enables picture adjustment to match
your TV's screen size (16:9 or 4:3).
Digital Photo Viewer (JPEG)
You can view Digital Photos on your TV.
Repeat
You can repeat a song or movie simply by pressing
the REPEAT button.
MP3/WMA
This unit can play discs created from MP3/WMA
files.
MPEG4
This unit can play MPEG4 formats within an avi file.
CD Ripping
This features lets you to copy audio files from disc
to USB device into MP3 format. (Only Audio CD
(CD DA)).
HDMI (High Definition Multimedia
Interface)
HDMI reduces picture noise by allowing a pure
digital video/audio signal path from the player to
your TV.
_ setup
Note
-Discs which cannot be played with this player.
• DVD-ROM
• DVD-RAM
• CD-ROM
• CDV
• CDI
• CVD
• CDGs play audio only, not graphics.
-Ability to play back may depend on recording
conditions.
• DVD-R, +R
• CD-RW
• DVD+RW, -RW (V mode)
-The unit may not play certain CD-R, CD-RW and DVD-R due to the disc type or recording
conditions.
COPY PROTECTION
Many DVD discs are encoded with copy protection.
Because of this, you should only connect your DVD
player directly to your TV, not to a VCR. Connecting
to a VCR results in a distorted picture from copyprotected DVD discs.
This product incorporates copyright protection technology that is protected by methods claims of
certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and other
rights owners. Use of this copyright protection
technology must be auzthorized by Macrovision
Corporation, and is intended for home and other
limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
PROGRESSIVE SCAN OUTPUTS
(576p,720p,1080p)
“CONSUMERS SHOULD NOTE THAT NOT ALL
HIGH DEFINITION TELEVISION SETS ARE
FULLY COMPATIBLE WITH THIS PRODUCT
AND MAY CAUSE ARTIFACTS TO BE
DISPLAYED IN THE PICTURE, IN CASE OF
576, 720, 1080 PROGRESSIVE SCAN PICTURE
PROBLEMS, IT IS RECOMMENDED THAT THE
USER SWITCH THE CONNECTION TO THE
‘STANDARD DEFINITION’ OUTPUT. IF THERE
ARE QUESTIONS REGARDING YOUR TV SET
COMPATIBILITY WITH THIS MODEL 576p,
720p, 1080p DVD PLAYER, PLEASE CONTACT
SAMSUNG'S CUSTOMER SERVICE CENTER.”
Disc Type and Characteristics
This DVD player is capable of playing the following types of discs with the corresponding logos:
Recording
Types
Disc
Size
Max. Playing Time
Characteristic
Audio
+
Video
12 Cm
Single-sided 240 min.
Double-sided 480 min
- DVD contains excellent sound and video due to
Dolby Digital and MPEG-2 system.
8 Cm
Single-sided 80 min.
Double-sided 160 min.
- Various screen and audio functions can be easily selected through the on-screen menu.
12 Cm
74 min.
8 Cm
20 min.
DVD
AUDIO-CD
Audio
Disc Markings
~
PAL
Play Region Number
PAL broadcast system in U.K, France,
Germany, etc.
Dolby Digital disc
STEREO
STEREO
DIGITAL
SOUND
Stereo disc
Digital Audio disc
- CD is recorded as a Digital Signal with better
audio quality, less distortion and less deterioration of audio quality over time.
Region Number
Both the DVD player and the discs are coded
by region. These regional codes must match
in order for the disc to play. If the codes do not
match, the disc will not play.
The Region Number for this player is
described on the bottom panel of the player.
DTS disc
MP3 disc
You must only insert one DVD disc at a time.
Inserting two or more discs will not allow to
play them back and it may cause damage to
the DVD player.
DivX Certification
DivX, DivX Certified, and associated logos are trademarks of
DivXNetworks, Inc and are used under
license
English _
● setup
Disc Types
(Logos)
setup
Description
Front Panel Controls
1. STANDBY/ON (
)
When STANDBY/ON is pressed on, the indicator goes
out and the player is turned on.
2. STANDBY Indicator
When the unit is first plugged in, the indicator lights.
3. DISC TRAY
Place the disc here.
4.
5.
OPEN/CLOSE/Stop ( )
Press to open and close the disc tray, Stops disc play.
PLAY/PAUSE (
)
Begin or pause disc play.
Rear Panel
1. DIGITAL AUDIO OUT JACKS
- Use coaxial digital cable to connect to a compatible
Dolby Digital receiver.
- Use coaxial digital cable to connect to an A/V
Amplifier that contains a Dolby Digital, MPEG2 or
DTS decoder.
2. COMPONENT VIDEO OUT JACKS
- Use these jacks if you have a TV with Component
Video in jacks. These jacks provide PR, PB and Y
video.
- If P-SCAN Video Output is selected in Setup Menu,
progressive scan mode will work.
- If I-SCAN Video Output is selected in Setup Menu,
interlaced scan mode will work.
3. AUDIO OUT JACKS
- Connect to the Audio input jacks of your television or
audio/video receiver.
_ setup
4. VIDEO OUT JACK
- Use a video cable to connect to the Video input jack
on your television.
5. USB Host
- Connect digital still camera, MP3 player, memory
stick, Card reader, or another removable storage
devices.
6. HDMI OUT JACK
- Use the HDMI cable to connect this jack to the HDMI
jack on your television for the best quality picture.
- If an HDMI cable is connected to an HDMI-compatible TV, HDMI will be output automatically within 10
seconds.
Note
Tour of the Remote Control
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
1. DVD Power Button
Turns the power on or off.
2. REPEAT Button
Allows you to repeat play a title, chapter, track or disc
3. DISC MENU Button
Brings up the Disc menu.
4. Bookmark Button
)
5. SEARCH Buttons (
/
Allow you to search forward/backward through a disc.
6. STOP Button ( )
7. SUBTITLE (π) Button
8. MENU Button
Brings up the DVD player’s menu.
9. AUDIO (√) Button
Use this button to access various audio functions on a disc.
10. ENTER/π/†,√/® Buttons
This button functions as a toggle switch.
11. INFO Button
Displays the current disc mode.
12. OPEN/CLOSE ( ) Button
To open and close the disc tray.
13. REPEAT A-B Butoon
Allows you to repeat play a chosen section (A-B) on a
disc.
14. USB button
15. PAUSE Button ( )
Pause disc play.
16. PLAY Button (
)
Begin disc play.
17. SKIP Buttons (
)
/
Use to skip the title, chapter or track.
18. RETURN Button
Returns to a previous menu.
19. TITLE MENU (®) Button
Brings up the Title menu.
20. CANCEL Button
Use to remove menus or status displays from the
screen.
English _
● setup
- Consult your TV User’s Manual to find out if your TV supports Progressive Scan (P-SCAN). If Progressive Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in
the TV’s menu system.
- The HDMI output of this unit can be connected to a DVI jack on a TV or other device using a conversion adapter. In this case, it is necessary to use a TV or display with an HDCP-compatible DVI input.
- There may be no image output if the DVD player is connected to a TV or display that is not compatible
with the above format.
- Refer to the TV's instruction manual for detailed information regarding the HDMI terminal.
- See pages 29 ~ 30 to get more information on how to use the setup menu.
connections
Choosing a Connection
The following shows examples of connections commonly used to connect the DVD player with a TV and
other components.
Before Connecting the DVD Player
- Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.
- Refer to the user’s manual of the additional components you are connecting for more information on those
particular components.
Connecting to a TV (VIDEO CVBS)
1
Using video/audio cables, connect the VIDEO (yellow)/
AUDIO (red and white) OUT terminals on the rear of the
DVD player to the VIDEO (yellow)/AUDIO (red and white)
IN terminals of TV.
2
Turn on the DVD player and TV.
RED
WHITE
Audio
Cable
3
RED
WHITE
YELLOW
Video Cable
YELLOW
Press the input selector on your TV remote control until
the Video signal from the DVD player appears on the TV
screen.
Note
- Noise may be generated if the audio cable is too close to the power cable.
- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 13 to 14)
- The number and position of terminals can vary depending on your TV set. Please refer to the user's
manual of the TV.
- If there is one audio input terminal on the TV, connect it to the [AUDIO OUT][left] (white) terminal of the
DVD player.
_ connections
Connection to a TV (Interlace)
- Connecting to your TV using Component video cables.
- You will enjoy high quality and accurate color reproduction images. Component video separates the picture element into black and white(Y), blue(PB), red(PR) signals to present clear and clean images. (Audio
signals are delivered through the audio output.)
● Connections
1
Using component video cables (not included), connect the
COMPONENT VIDEO OUT terminal on the rear of the
DVD player to the COMPONENT IN terminal of TV.
2
Using the audio cables, connect the AUDIO (red and
white) OUT terminals on the rear of the DVD player to the
AUDIO (red and white) IN terminals of TV. Turn on the
DVD player and TV.
RED
3
Press the input selector on your TV remote control until
the Component signal from the DVD player appears on the
TV screen.
BLUE
GREEN
WHITE
RED
Audio Cable
Component cable
RED
WHITE
RED
BLUE
GREEN
4
Set the Video Output to I-SCAN in the Display Setup
menu. (See pages 29-30)
Note
- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 13 to 14)
- The component terminal of TV can be marked by “R-Y, B-Y, Y” or “Cr, Cb, Y” instead of “PR, PB, Y” depending on the manufacturer. The number and position of terminals can vary depending on the TV set.
Please refer to the user's manual of the TV.
English _
connections
Connection to a TV (Progressive)
1
Using component video cables (not included), connect the
COMPONENT VIDEO OUT terminal on the rear of the
DVD player to the COMPONENT IN terminal of TV.
2
Using the audio cables, connect the AUDIO (red and
white) OUT terminals on the rear of the DVD player to the
AUDIO (red and white) IN terminals of TV. Turn on the
DVD player and TV.
RED
3
Press the input selector on your TV remote control until
the Component signal from the DVD player appears on the
TV screen.
RED
BLUE
GREEN
WHITE
Audio Cable
RED
WHITE
RED BLUE
GREEN
Component cable
4
Set the Video Output to P-SCAN in the Display Setup
menu. (See pages 29-30)
To see the progressive video output,
-
Consult
TVsupporting
User’s Manual
to find out
You
need ayour
TV set
the progressive
scanif your TV supports Progressive Scan. If Progressive
Scan
supported,
follow
TV up
User’s
Manual regarding Progressive Scan settings in the TV’s
input
isfunction.
And you
havethe
to set
the TV
menu system.
- Depending on your TV, the connection method may differ from the illustration above.
Note
- What is "Progressive Scan"?
Progressive scan has twice as many scanning lines as the interlace output method has. Progressive
scanning method can provide better and clearer picture quality.
10_ connections
Connecting to a TV with DVI Jack
1
● Connections
Using an HDMI-DVI cable (not included), connect the
HDMI OUT terminal on the rear of the DVD player to the
DVI IN terminal of your TV.
2
Using the audio cables, connect the AUDIO (red and
white) OUT terminals on the rear of the DVD player to the
AUDIO (red and white) IN terminals of your TV.
Turn on the DVD player and TV.
RED
WHITE
Audio Cable
RED
WHITE
HDMI-DVI cable
3
Press the input selector on your TV remote control until
the DVI signal from the DVD player appears on your TV
screen.
Connecting to a TV with HDMI Jack
1
Using the HDMI-HDMI cable connect the HDMI OUT terminal on the rear of the DVD player to the HDMI IN terminal
of your TV.
2
Press the input selector on your TV remote control until
the HDMI signal from the DVD player appears on your TV
screen.
HDMI cable
HDMI VIDEO Specifications
- Depending on your TV, certain HDMI output resolutions may not work.
- Please refer to the user's manual of your TV.
- If HDMI or HDMI-DVI cable is plugged into TV, the DVD player’s output is set to HDMI/DVI within 10
‑seconds.
- If you set the HDMI output resolution 720p,1080p or 1080i, HDMI output provides better picture
‑quality.
- If you connect an HDMI cable between Samsung TV and this DVD player, you can operate this DVD player
using your TV remote control. This is only available with Samsung TVs that support Anynet+(HDMI-CEC).
(See page 32).
- If your TV has an
logo, then it will
Supports the Anynet+ Function.
English _11
connections
• HDMI (High Definition Multimedia Interface)
HDMI is an interface to enable the digital transmission
of video and audio data with just a single connector.
Using HDMI, the DVD player transmits a digital video
and audio signal and displays a vivid picture on a TV
having an HDMI input jack.
• HDMI connection description
HDMI connector - Both uncompressed video data and
digital audio data (LPCM or Bit Stream data).
- Though the player uses a HDMI cable, the player
outputs only a pure digital signal to the TV.
- If TV does not support HDCP (High-bandwidth
Digital content protection), snow noise appears on
the screen.
12_ connections
• Why does Samsung use HDMI?
Analog TVs require an analog video/audio signal.
However, when playing a DVD, the data transmitted
to a TV is digital. Therefore either a digital-to-analog
converter (in the DVD player) or an analog-to-digital
converter (in the TV) is required. During this conversion, the picture quality is degraded due to noise and
signal loss. DVI technology is superior because it
requires no D/A conversion and is a pure digital signal from the player to your TV.
• What is the HDCP?
HDCP (High-bandwidth Digital Content Protection)
is a system for protecting DVD content outputted
via DVI from being copied. It provides a secure
digital link between a video source (PC, DVD. etc)
and a display device (TV, projector . etc). Content is
encrypted at the source device to prevent unauthorized
Connection to an Audio System (2 Channel Amplifier)
1
Using the audio cables, connect the AUDIO (red and
white) OUT terminals on the rear of the DVD player to the
AUDIO (red and white) IN terminals of the Amplifier.
● Connections
2
Using the video signal cable(s), connect the VIDEO or
COMPONENT OUT terminals on the rear of the DVD
player to the VIDEO or COMPONENT IN terminal of your
TV as described on pages 8 to 11.
3
RED
Turn on the DVD player, TV, and Amplifier.
WHITE
Audio Cable
RED
4
WHITE
2-Channel stereo amp
Press the input select button of the Amplifier to select
external input in order to hear sound from the DVD player.
Note
- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause
damage to the speakers or to your hearing.
- Please set the audio in the menu screen according to the Amplifier. (See pages 28 to 29)
- The position of terminals can vary depending on the Amplifier.
Please refer to the user's manual of the Amplifier.
English _13
connections
Connection to an Audio System (Dolby Digital, MPEG2 or DTS Amplifier)
1
If using a coaxial cable (not included), connect the
DIGITAL AUDIO OUT (COAXIAL) terminal on the rear
of the DVD player to the DIGITAL AUDIO IN (COAXIAL)
terminal of the Amplifier.
2
Using the video signal cable(s), connect the VIDEO, COMPONENT or HDMI OUT terminals on the rear of the
DVD player to the VIDEO, COMPONENT or DVI IN terminals of your TV as described on pages 8 to 11.
3
Coaxial Cable
Turn on the DVD player, TV, and Amplifier.
Dolby Digital or
DTS amp
4
Press the input select button of the Amplifier to select
external input in order to hear sound from the DVD player.
Refer to your Amplifier's user manual to set the Amplifier's
audio input.
Note
- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause
damage to the speakers or to your hearing.
- Please set the audio in the menu screen according to the Amplifier. (See pages 28 to 29)
- The position of terminals can vary depending on the Amplifier.
Please refer to the user's manual of the Amplifier.
14_ connections
basic functions
Playing a Disc
- If you connected an external Audio System, turn
on your Audio System and set it to the correct
Audio Input.
After plugging in the player, the first time you press the DVD
POWER button, this screen comes up: If you want to select
a language, Press the π/† buttons, and then press the
ENTER button. (This screen will only appear when you plug
in the player for the first time.)
If the language for the startup screen is not set, the settings may change whenever you turn the power on or off.
Therefore, make sure that you select the language you want
to use.
Once you select a menu language, you can change it by
) button on the front panel of the unit
pressing the (
for more than 5 seconds with no disc in the unit. Then the
SELECT MENU LANGUAGE window appears again where
you can reset your preferred language.
Select Menu Language
English
Français
Deutsch
Español
Italiano
Nederlands
Playback
1. Press the OPEN/CLOSE ( ) button. The STANDBY indicator light goes out and the tray opens.
2. Place a disc gently into the tray with the disc’s label facing up.
3. Press the PLAY ( ) button or OPEN/ CLOSE ( ) button to close the disc tray. When you stop disc play, the
player remembers where you stopped, so when you
press PLAY ( ) button again, it will pick up where you
left off.
) button during play.
5. Removing Disc
Press the OPEN/CLOSE (
) button.
6. Pausing Play
Press the PAUSE ( ) button on the remote control during
play.
- Screen stops, no sound.
To resume, press the PLAY ( ) button once again.
7. Slow Motion Play
) button to choose the play
Press the SEARCH ( /
speed between 1/2, 1/4 1/8 and 1/16 theofnormal speed
during PAUSE mode.
- No sound is heard during slow mode.
- Press the PLAY( ) button to resume normal play.
8. Step Motion Play (Except CD)
Press the SKIP ( ) button on the remote control
during PAUSE mode.
- Each time the button is pressed, a new frame will appear.
- No sound is heard during STEP mode.
- Press the PLAY ( ) button to resume normal play.
- You can only perform step motion play in the forward direction.
Note
- If the player is left in the stop mode for more
than one minute without any user interaction, a screen saver will be activated. Press the PLAY
( ) button to resume normal play.
- If the player is left in the stop mode for more than about 30 minutes, the power will automatically
shut off.(Automatic Power-Off Function)
- If the player is left for about 5 minutes in pause mode, it will stop.
- This (
) icon indicates an invalid button press.
English _15
● basic functions
Before Play
- Turn on your TV and set it to the correct Video
Input by pressing TV/VIDEO button on the TV
remote control.
4. Stopping Play
Press the STOP (
basic functions
Using the Search and Skip
Functions
During play, you can search quickly through a chapter or
track, and use the skip function to jump to the next selection.
Searching through a Chapter or
Track
During play, press the SEARCH ( or
remote control for more than 1 second.
DVD
2X, 4X, 64X, 128X
CD
2X, 4X, 8X
) button on the
Using the Display Function
When Playing a DVD/MPEG4
1. During play, press the INFO button on the remote control.
2. Press the π/† buttons to select the desired item.
3. Press the √/® buttons to make the desired setup and then press the ENTER button.
4. To make the screen disappear, press the INFO button again.
Note
To access the desired title when there is more
than one in the disc.
For example, if there is more than one movie
on a DVD, each movie will be identified.
Note
- The speed marked in this function may be different from the actual playback speed.
- No sound is hearing during search mode
(Except CD).
Most DVD discs are recorded in chapters so
that you can quickly find a specific passage
(similar to tracks on an audio CD).
Allows playback of the film from a desired
time. You must enter the starting time as a
reference.
The time search function does not operate
on some discs
Skipping Tracks
During play, press the SKIP (
or
) button.
- When playing a DVD, if you press the SKIP (
) button, it
Refers to the film's soundtrack language.
In the example, the soundtrack is played in
English 5.1CH.A DVD disc can have up to
eight different soundtracks.
moves to the next chapter. If you press the SKIP
(
) button, it moves to the beginning of the chapter. One
more press makes it move to the beginning of the previous
Refers to the subtitle languages available
in the disc. You will be able to choose the
subtitle languages or, if you prefer, turn them
off from the screen. A DVD disc can have up
to 32 different subtitles
chapter.
- When playing a CD in Menu Off mode, if you press the
SKIP (
) button, it moves to the next track. If you press
the SKIP (
) button, it moves to the beginning of the
track. One more press makes it move to the beginning of
the previous track.
EZ
The EZ View funtion is use for changing the
aspect ratio in DVD.
This button has function as shortcut. Press
enter to activate the Zoom function.
To access the desired Angle function.
Some DVD disc are have more than one
recorded angle.
16_ basic functions
Using the Disc and Title
Menu
Disc
Using the Disc Menu
1. During the playback of a DVD disc, press the DISC MENU
button on the remote control.
Note
- The disc menu may not work on certain disc
types.
- You can also use the Disc Menu, using the
DISC MENU button on the remote control.
Using the A-B Repeat function
1. Press the REPEAT A-B button on the remote control at
the point where you want repeat play to start (A).
2. Press the REPEAT A-B button on the remote control at
the point where you want the repeat play to stop (AB).
DVD
A
AB
Using the Title Menu
1. During the playback of a DVD disc, press the ® /TITLE
MENU button on the remote control.
2. Press the π/† buttons to select for navigation/change
selection, then press the ENTER button.
3. To make the screen disappear, press the RETURN button
again.
Note
- The disc menu may not work on certain disc
types.
- Title Menu will only be displayed if there are at
least two titles in the disc.
Repeat Play
Press the REPEAT button to change playback
mode.
When playing a DVD
- DVD repeats play by chapter or title.
- Chapter : repeats the chapter that is playing.
- Title : repeats the title that is playing.
- Disc : repeats the disc that is playing.
- Off
Off
Note
- A-B REPEAT allows you to set point (AB) directly
after point (A) has been set.
- The disc menu may not work on certain disc
types.
Slow Play
This feature allows you to slowly repeat scenes containing sports, dancing, musical instruments
being played etc., so you can study them more
closely.
When playing a DVD
1. During play, press the PAUSE ( ) button.
2. Press the SEARCH (
) button to choose the play
/
speed between 1/2, 1/4, 1/8 and 1/16 of normal during
PAUSE mode.
Chapter
Title
English _17
● basic functions
2. Press the π/† buttons for navigation/change selection,
then‑press ENTER button.
3. To make the screen disappear, press the RETURN or DISC
MENU button again.
Off
advanced functions
Adjusting the Aspect Ratio
(EZ View)
To play back using aspect ratio
(DVD)
1. During play, press the INFO button on the remote control.
2. Press the π/† buttons to select EZ icon. Press the √/® buttons, the screen size change when these button is pressed.
3. To make the screen disappear, press the INFO button again.
If you are using a 16:9 TV
For 16:9 aspect ratio discs
- Wide Screen
Displays the content of the DVD title in 16:9 aspect ratio.
- Screen Fit
The top and bottom portions of the screen are cut off.
When playing a 2.35:1 aspect ratio disc, the black bars at
the top and bottom of the screen will disappear. The picture
will look vertically stretched. (Depending on the type of
disc, the black bars may not disappear completely.)
- Zoom Fit
The top, bottom, left and right of the screen are cut off and
the central portion of the screen is enlarge
For 4:3 aspect ratio discs
- Normal Wide
Displays the content of the DVD title in 16:9 aspect ratio.
The picture will look horizontally stretched.
- Screen Fit
The top and bottom portions of the screen are cut off and
the full screen appears.
The picture will look vertically stretched.
- Zoom Fit
The top, bottom, left and right portions of the screen are
cut off and the central portion of the screen is enlarged.
- Vertical Fit
When a 4:3 DVD is viewed on a 16:9 TV, black bars will
appear at the left and right of the screen in order to prevent
the picture from looking horizontally stretched.
18_ advanced functions
If you are using a 4:3 TV
For 16:9 aspect ratio discs
- 4:3 Letter Box
Displays the content of the DVD title in 16:9 aspect ratio.
The black bars will appear at the top and bottom of the
screen.
- 4:3 Pan Scan
The left and right portions of the screen are cut off and the
central portion of the 16:9 screen is displayed.
- Screen Fit
The top and bottom portions of the screen are cut off and a
full screen appears. The picture will look vertically stretched.
- Zoom Fit
The top, bottom, left and right of the screen are cut off and
the central portion of the screen is enlarged.
For 4:3 aspect ratio discs
- Normal Screen
Displays the content of the DVD title in 4:3 aspect ratio.
- Screen Fit
The top and bottom portions of the screen are cut off and
the full screen appears. The picture will look vertically
stretched.
- Zoom Fit
The top, bottom, left and right portions of the screen are cut
off and the central portion of the screen is enlarged.
Note
This function may behave differently depending on
the type of disc.
Selecting the Audio
Language
You can select a desired audio language quickly and
easily with the √/AUDIO button.
Using the √/AUDIO button (DVD/
MPEG4)
1. Press the √/AUDIO button. The Audio changes when the button is pressed repeatedly. The audio languages are represented by abbreviations.
DVD
ENG DTS
5.1 CH
Press √/AUDIO button
at remote control repeatedly to select the desired
Audio on MPEG4 then
press the ENTER .
MPEG4
1/1 MP3 2CH
-A DVD disc can contain up to 8 audio languages.
-To have the same audio language come up
whenever you play a DVD;
Refer to “Using the Audio Language” on page 28.
- Possible warning messages that may appear if the
device (TV) that connected to the HDMI can't support RAW digital audio.
Selecting the Subtitle
Language
You can select a desired subtitle quickly and
easily with the π/SUBTITLE button.
Using the π/SUBTITLE button
(DVD/MPEG4)
Changing the Camera
Angle
When a DVD contains multiple angles of a particular
scene, you can use the ANGLE function.
Using the ANGLE function (DVD)
If the disc contains multiple angles, the ANGLE
appears on the screen.
1. During play, press the INFO button on the remote control.
icon.
2. Press the π/† buttons to select
3. Press the √/® buttons on the remote control to select the desired angle.
4. To make the screen disappear, press the INFO button again.
1. Press the π/SUBTITLE button. The subtitle languages are represented by abbreviations. The subtitle changes when
the button is pressed repeatedly.
DVD
English
Repeatedly Press π/
SUBTITLE button
on the remote control to
select the desired
subtitle language on
MPEG4 then press ENTER .
MPEG4
Note
- If the disc has only one angle, this feature won’t
work. Currently, very few discs have this feature.
- Depending on the disc, these functions may not
work.
Subtitle 1/5
English _19
● advanced functions
Note
-This function depends on audio languages encoded on the disc and may not work.
Note
- You have to change the desired subtitle in the Disc Menu, according to discs. Press the DISC
MENU button.
- This function depends on what subtitles are
encoded on the disc and may not work on all DVDs.
- A DVD disc can contain up to 32 subtitle
languages.
- To have the same subtitle language come up
whenever you play a DVD; Refer to “Using the
Subtitle Language” on page 28.
advanced functions
Using the Bookmark
Function
Using the Zoom Function
This feature lets you bookmark sections of a DVD so
you can quickly find them at a later time.
Using the Bookmark Function (DVD)
1. During play, press the Bookmark button on the remote con Using the Zoom Function (DVD)
1. During play, press the INFO button on the remote control.
icon, then press the
2. Press the π/† buttons to select
ENTER button to zoom in 2x, 3x, 4x.
3. To make the screen disappear, press the INFO button again.
trol.
2x
2. When You reach the scene you want to mark, press the ENTER button. Up to 12 scenes may be marked at a time.
Bookmark
Clear
Play
Bookmark
Bookmark
1
Clear
Play
TT:01 CH:05 Time 0:39:23
Clear
Play
Bookmark
1
Bookmark
TT:01 CH:05 Time 0:39:23
2
1
Clear
Play
TT:01 CH:05 Time 0:39:23
Play
Bookmark
Clear
2
1
Note
Clear
Play
- These functions may not Bookmark
Work Play
on certain
disc
Clear
types.
Bookmark
TT:01 CH:05 Time 0:39:23
1
3
2
TT:01 CH:05 Time 0:39:23
1
3
2
TT:01 CH:05 Time 0:39:23
Play
Recalling a Marked Scene
Clear
1. During play,press the Bookmark button on the remote
Bookmark
control.
2. Press the √/®/π/† buttons to select a marked scene.
Clear
Play
to skip to the
3. Press the PLAY ( ) buttonBookmark
1
marked scene.
TT:01 CH:05 Time 0:39:23
Clear
Play
Bookmark
1
CANCEL
2
TT:01 CH:05 Time 0:39:23
Clear
Play
Bookmark
Bookmark
Clearing a Bookmark
1
3
2
TT:01 CH:05 Time 0:39:23
Clear
Clear
Play
Play
Bookmark
1. During play,press the Bookmark button on the remote
1
control.
2. Press the √/®/π/† buttons to select a marked Clear
Play
scene.
Bookmark
3. Press the CANCEL button to
delete
a
bookmark
2
1
number.
TT:01 CH:05 Time 0:39:23
TT:01 CH:05 Time 0:39:23
Play
Clear
Bookmark
1
2
3
CANCEL
TT:01 CH:05 Time 0:39:23
Play
20_ advanced functions
Clear
Clips Menu for MP3/WMA/
JPEG/MPEG4/CD Audio
CD Audio or discs with MP3/WMA/JPEG/MPEG4
contain individual songs and/or pictures that will be
organized into folders on this unit as shown below.They
are similar to how you use your computer to put files
into different folders.
Open the disc tray.
Place the disc on the tray.
Close the tray.
The tray closes and this
screen displays.
Off
001/004
: Current Playback Mode : There are four modes.
They can be selected in order by pressing the REPEAT button.
- Off : Normal Playback.
- Track : Repeats the current track.
- Folder : Repeats the current folder.
- Random : Files in the disc will be played in random order.
-
: STOP icon
-
: PLAY file icon
: MP3 file icon
-
: WMA file icon
-
: JPEG file icon
-
: AVI file icon
: CD Audio file icon
-
: Folder icon
: Current Folder icon
Folder Selection
- To select the Parent Folder
Press the RETURN button to go to parent folder, or press
the π/† buttons to select “..” and press ENTER to go to
the parent folder.
MP3/WMA/CD Audio Playback
1. Open the disc tray. Place the disc on the tray. Close the tray.
- Only one kind of file is played back when a disc or a folder contains both MP3 and WMA files.
2. Press the π/† buttons to select a song file.
Press ENTER to begin playback of the song file.
Repeat/Random playback
Press the REPEAT button to change the playback mode. There
are four modes: Off, Track, Folder and Random.
- Off: Normal Playback
- Track: Repeats the current song file.
- Folder: Repeats the song files which have the same extension in the current folder.
- Random: Song files which have the same extension will be played in random order.
CD-R MP3/WMA file
When you record MP3 or WMA files on CD-R, please refer
to the following.
- Your MP3 or WMA files should be ISO 9660 or JOLIET format.
ISO 9660 format and Joliet MP3 or WMA files are compatible
with Microsoft's DOS and Windows, and with Apple's Mac.
This format is the most widely used.
- When naming your MP3 or WMA files, do not exceed 8
characters, and enter “.mp3, .wma” as the file extension.
General name format : Title.mp3. or Title.wma. When composing your title, make sure that you use 8 characters
or less, have no spaces in the name, and avoid the use of special characters including: (.,/,\,=,+).
- Use a decompression transfer rate of at least 128 Kbps when recording MP3 files.
Sound quality with MP3 files basically depends on the rate
of compression/decompression you choose. Getting CD
audio sound requires an analog/digital sampling rate, that is conversion to MP3 format, of at least 128 Kbps and up to
160 Kbps. However, choosing higher rates, like 192 Kbps
or more, only rarely give better sound quality. Conversely,
files with decompression rates below 128 Kbps will not be
played properly.
- Use a decompression transfer rate of at least 64Kbps when recording WMA files.
Sound quality with WMA files basically depends on the rate of
compression/decompression you choose.
Getting CD audio sound requires an analog/digital sampling rate, that is conversion to WMA format, of at least 64Kbps and up to 192Kbps. Conversely, files with decompression rates below 64Kbps or over 192Kbps will not be played properly.
- Do not try recording copyright protected MP3 files.
Certain "secured" files are encrypted and code protected to prevent illegal copying. These files are of the following types: Windows MediaTM (registered trade mark of Microsoft
Inc) and SDMITM (registered trade mark of The SDMI
Foundation). You cannot copy such files.
- Important:
The above recommendations cannot be taken as a guarantee that the DVD player will play MP3 recordings,
or as an assurance of sound quality. You should note that
certain technologies and methods for MP3 file recording on
CD-Rs prevent optimal playback of these files on your DVD
player (degraded sound quality and in some cases, inability
of the player to read the files).
- This unit can play a maximum of 500 files and 500 folders per disc.
To resume normal play, press the CANCEL button.
English _21
● advanced functions
-
-
advanced functions
MPEG4 Playback
MPEG4 Play Function
AVI files are used to contain the audio and video data.
Only AVI format files with the “.avi” extensions can be
played.
1. Open the disc tray. Place the disc on the tray.
Close the tray.
2. Press the π/† or √/® buttons to select an avi file
(DivX/XviD) andthenpress ENTER button.
001/005
Off
Repeat playback
Press the REPEAT button to change playback mode. There are
3 modes: - Off, Folder and Track.
- Folder : repeats the AVI files which have the same extension
in the current folder.
- Track : repeats the track that is playing.
MPEG4 Function Description
Function
Skip
or
(
(
Description
)
Search
or )
Reference
Page
During Play, press the
button, it moves
or
forward or backward 5
minutes.
-
During play, press the
) button
SEARCH ( or
and press again to search at
a faster speed. Allows you to
search at a faster speed in an
AVI file (2X, 4X, 8X)
-
DVD-RW & DVD+R
Format that support for DivX file :
- Basic DivX format DivX3.11 / 4.12/ 5.x
- Xvid (MPEG-4 compliant video codec) and DivX Pro
- File format : *.avi, *.div, *.divx.
This unit supports all resolutions up to maximum below.
DivX3.11 & DivX4 & Xvid
DivX5
Bit rate may fluctuate:
Device may skip decoding the high bit
rate portions and begin decoding again when bit
rate returns to normal
720 x 480 @30fps
720 x 576 @25fps
: Maximum bit rate
:4Mbps
Possible warning messages that may appear when trying to
play DivX/AVI files are :
1. No Authorization
- File with bad registration code.
2. Unsupported Codec
- Files with certain Codec Types, Versions
(ex. MP4, AFS and other proprietary codecs) are not
supported bythis player.
3. Unsupported Resolution
- Files containing resolutions higher than the player’s
specification are not supported.
This file is not supported
Slow Motion
Play
Allows you to search at a
slower sspeed in an AVI
file. (1/2X, 1/4X, 1/8X, and
1/16X)
P 15
ZOOM
2X/ 3X/ 4X/ Normal in order
P 20
OK
- These functions may not work depending on MPEG4 file.
22_ advanced functions
CD-R AVI file
This unit can play the following video compression formats
within the AVI file format:
- DivX 3.11 contents
- DivX 4 contents (Based on MPEG-4 Simple Profile)
- DivX 5 contents (MPEG-4 simple profile plus additional fea
tures such as bi-directional frames. Qpel and GMC are also supported.)
- XviD MPEG-4 compliant Contents.
Note
- The resolution that can be supported by DVDH1080 model up to 720 x 480 @30 frames/720 x
576 @25 frames.
- This unit supports CD-R/RW written in MPEG4 in
accordance with the “ISO9660 format”.
You can enjoy the media files such as pictures, movies
and tunes saved in an MP3 player, USB memory or digital
camera in high audio by connecting the storage device to
the USB port of the DVD Player.
Using the USB HOST feature
1. Connect the USB device to the USB port on the rear of the
unit.
2. If there is partition on USB, Press the √/® button to select
the one of partitions from USB and Press ENTER.
Device
Disc
USB 1
3. Press the π/† buttons to select a file in
USB. Press ENTER to Open file.
0:00:00 0:00:00
001/003
Off
To prevent damage to the memory stored in the USB device,
perform safe removal before disconnecting the USB cable.
- Press the STOP ( ) button.
- Remove the USB cable.
Skip Forward/Back
During playback, press the ( / ) button.
• When there is more than one file, when you press the
button, the next file is selected
• When there is more than one file, when you press the
button, the previous file is selected
Fast playback
To play back the disc at a faster speed, press (
/
)
during playback.
• Each time you press either button, the playback speed will
change as follows : 2x ➞ 4x ➞ 8x.
Compatible Devices
1. USB devices that support USB Mass Storage v1.0.
(USB devices that operate as a removable disk in Windows (2000 or later) without additional driver installation.)
2. MP3 Player: Flash type MP3 player.
3. Digital camera: Cameras that support USB Mass Storage
v1.0.
•Cameras that operate as a removable disk in Windows (2000 or later) without additional driver installation.
4. USB Flash Drive: Devices that support USB2.0 or USB1.1
•You may experience a difference in playback quality when you connect a USB1.1 device.
5. USB card Reader: One slot USB card reader and Multi slot
USB card reader
•The USB card reader may not be supported dependent upon manufacturer.
• If you install multiple memory devices into a multi card
reader, you may experience problems.
6. If you use a USB extension cable, the USB device might not
be recognized.
0:00:00 0:00:00
001/003
Note
- Each time the USB button on the remote control
is pressed, a frame of the USB device selection
will appear.
- " Press USB to select device" appear at the top
left corner for a moment.
- USB MENU screen appears on the TV screen and
the saved file is played.
English _23
● advanced functions
Playing Media Files Using the
USB Host feature
Safe USB Removal
advanced functions
•
Supported Formats
Still
Picture
Music
Movie
File
Name
File
extension
Bit Rate
Version
Pixel
Sampling
Fequency
JPG
JPG .JPEG
-
-
640*480
44.1KHz
MP3
.MP3
80~384kbps
-
-
WMA
.WMA
56~128kbps
V8
-
44.1KHz
DivX
.AVI, .ASF
4Mbps
.DivX3.11~DivX5, Xvid
720*480
44.1KHz~48KHz
Note
- VCD & WMV Can't be played on this player.
• CBI (Control/Bulk/Interrupt) is not supported.
• Digital Cameras that use PTP protocol or require additional
program installation when connected to a PC are not
supported.
• A device using NTFS file system is not supported.
(Only FAT 16/32 (File Allocation Table 16/32) file system is
supported.)
• Some MP3 players, when connected to this product,may not
operate depending on the sector size of their file system
• The USB HOST function is not supported if a product that
transfers media files by its manufacturer-specific program is
connected.
• Does not operate with Janus enabled MTP(Media Transfer
Protocol) devices.
CD Ripping
This feature lets you to copy audio files from disc to USB
device into MP3 format.
1. Open the disc tray. Place The Audio CD(CD DA) disc on
the tray, and close the tray. Connect the USB device to the
USB port on the rear of the unit. Press ENTER to select the
DISC.
Bitrate 128kbps
Device USB 1
Select all
Start
4. Press the ® buttons to select menu ripping START, then
press the ENTER button.
Bitrate 128kbps
Device USB 1
Select all
Start
Ripping Menu contains 4 buttons :
- Bit rate, press ENTER to change 128kbps g192kbps g128kbps...
- Device selection, press ENTER to change between devices (max 4)
- Select - Unselect, press ENTER to change from Select all or Select none.
- Start ripping, press ENTER to start ripping process
5. Press the π/† buttons to START, then press the ENTER
button. File copy begins.
- To cancel the copying in progress, press the CANCEL button.
Off
Bitrate 128kbps
Device USB 1
DEVICE
DISC
Ripping...
USB 1
2. With the unit in stop mode, press the RETURN button to
display Ripping screen. 3. Press the π/† buttons to select the desired files, then
press the ENTER button to marked files to be copying. - To unmarked copying all files press ENTER button again.
24_ advanced functions
Cancel
TRACK01
Note
- To return to CDDA screen, press the RETURN
button again.
- When the CD ripping is in process the player will
automatically begin playing.
- Only Audio CD (CD DA) discs can be ripped.
- Because the speed is 2.6x of normal speed. User
is unable to play the CD DA through the ripping
process.
Picture CD Playback
1. Select the desired folder.
2. Press the π/† buttons to select a Picture file in the clips menu and then press the ENTER button.
MP3-JPEG Playback
Note
- MP3 and JPEG files have to be on the same disc.
Rotation
- Each time the √/® button is pressed,the picture rotates 90 degrees clockwise.
- Each time the π button is pressed, the picture will reverse to the upside down to show a mirror image.
- Each time the † button is pressed, the picture will reverse
to the right side to show a mirror image.
Slide show
- When you press the PLAY atJPEG file, itwill go to full screen mode and automatically slide show.
CD-R JPEG Disc
- Only files with the “.jpg” and “.JPG” extensions can be played.
- If the disc is not closed, it will take longer to start playing and not all of the recorded files may be played.
- Only CD-R discs with JPEG files in ISO 9660 or Joliet format can be played.
- The name of the JPEG file may not be longer than 8 characters and should contain no blank spaces or special characters (. / = +).
- Only a consecutively written multi-session disc can be played. If there is a blank segment in the multi-session disc, the disc can be played only up to the blank segment.
- A maximum of 3000 images can be stored on a single CD.
- Kodak Picture CDs are recommended.
- When playing a Kodak Picture CD, only the JPEG files in the pictures folder can be played.
- Kodak Picture CD: The JPEG files in the pictures folder can be played automatically.
- Konica Picture CD: If you want to see the Picture, select the JPEG files in the clips menu.
- Fuji Picture CD: If you want to see the Picture, select the JPEG files in the clips menu.
- QSS Picture CD: The unit may not play QSS Picture CD.
- If the number of files in 1 Disc is over 500, only 500 JPEG files can be played.
- If the number of folders in 1 Disc is over 500, only JPEG files in 500 folders can be played
Note
- Depending on the file size, the amount of time
between each picture may be different from the
set interval time.
- If you don’t press any button, the slide show will
start automatically in about 10 seconds by default.
English _25
● advanced functions
You can play JPEG using music as a backgound.
1. Press the π/† buttons to select an MP3 file in the clips menu and then press the ENTER button.
2. Press the π/† buttons to select a JPEG file in the clips menu and then press the ENTER button.
- Music willplay from the beginning
3. Press Stop button when you want to stop the
playback.
advanced functions
Picture CD Playback for
HD-JPEG
To enjoy HD-JPEG, HDMI must be connected and the
resolution should be to 720p/1080i/1080p. Please set the
HDMI as highest Resolution which your TV support.
1. Select the desired folder.
- Rotation
Press the √/® button to rotate the screen 90 degrees to the
left/right.
- Skip Picture
Press the
or
button to select previous or next picture.
- Slide Show
Press the PLAY ( ) button to start SLIDE function.
Press the STOP ( ) button to stop SLIDE function.
2. Press the π/† buttons to select a Picture file in the clips
menu and then press the ENTER button.
- Press the STOP ( ) button to return to the clips menu.
- When Playing a Kodak Picture CD, the unit displays
the Photo directly, not the clips menu.
Note
- To make the setup menu disappear, press the
MENU button.
26_ advanced functions
Note
- Depending on a file size, the amount of time
between each picture may be different.
- The image may be displayed at a smaller size
depending on the picture size when displaying
images in HD-JPEG mode.
- It is recomended to set the "BD Wise" to "Off".
In case of playback JPEG image file bigger than
720x480 pixel size.
changing setup menu
Using the Setup Menu
The Setup menu lets you customize your DVD player by
parental level, even adjust the player to the type of television
screen you have.
1. Press the MENU button on the remote control. Use the √/® buttons to select Setup, then press the † or ENTER button.
-- Language Setup Page --
Player Menu
ENG
Disc Menu
ENG
Audio
ENG
AUTO
Subtitle
DivX Subtitle
Western
If you set the player menu, disc menu, audio and subtitle
language in advance, they will come up automatically every
time you watch a movie.
Using the Player Menu Language
1. Press the MENU button.
2. Press the √/® buttons to select Language Setup Page, then press the † or ENTER button.
3. Press the π/† buttons to select Player Menu, then press the ® or ENTER button.
4. Press the √/® buttons to select the desired language, then press the ENTER button.
– The language is selected and the screen returns to the Language Setup menu.
– To make the setup menu disappear, press the MENU but ton.
❶ Language Setup Page: Setup of the Language.
❷ Audio Setup Page: Setup of the Audio Options.
❸ Display Setup Page:Setup of the Display Options. Use to
select which type of screen you want to watch and several
display options.
❹ Parental Page: Setup of the Parental Level. Allows users
to set the level necessary to prevent children from viewing
unsuitable movies such as those with violence, adult
subject matter, etc.
❺ HDMI Page:
2. Press the √/® buttons to access the different features. Press the † or ENTER button to access the sub features.
3. To make the setup screen disappear after setting up, press
the MENU button again.
Note
- On some discs, setup menu selections
may not work.
-- Language Setup Page --
Player Menu ENG
English
Français
Disc Menu
ENG
Audio
ENG
Deutsch
Español
Subtitle
AUTO
DivX Subtitle
Western Italiano
Nederlands
Using the Disc Menu Language
1. Press the MENU button.
2. Press the √/® buttons to select Language Setup Page, then press the † or ENTER button.
3. Press the π/† buttons to select Disc Menu, then press the ® or ENTER button.
4. Press the √/® buttons to select the desired language, then press the ENTER button.
– The language is selected and the screen returns to the Language Setup menu.
– To make the setup menu disappear, press the MENU but ton.
-- Language Setup Page -Player Menu
Disc Menu
Audio
Subtitle
DivX Subtitle
ENG
English
ENG
Français
ENG
Deutsch
Español
AUTO
Western Italiano
Nederlands
Cesky
English _27
● changing setup menu
allowing you to select various language preferences, set up a
Setting Up the Language
Features
changing setup menu
Using the Audio Language
Using the DivX Subtitle Language
1. Press the MENU button.
2. Press the √/® buttons to select Language Setup Page, then press the † or ENTER button.
3. Press the π/† buttons to select Audio, then press the ® or ENTER button.
4. Press the √/® buttons to select the desired language, then press the ENTER button.
– Select “Original” if you want the default soundtrack
language to be the original language the disc is recorded in.
– If the selected language is not recorded on the disc, the
original pre-recorded language is selected.
– The language is selected and the screen returns to the Language Setup menu.
– To make the setup menu disappear, press the MENU but
ton.
1. Press the MENU button.
2. Press the √/® buttons to select Language Setup Page, then press the † or ENTER button.
3. Press the π/† buttons to select DIvX Subtitle, then press the ® or ENTER button.
4. Press the √/® buttons to select the desired language, then press the ENTER button.
– The language is selected and the screen returns to the setup menu.
– To make the setup menu disappear, press the MENU but
ton.
-- Language Setup Page --
Player Menu ENG
English
Français
Disc Menu
ENG
Audio
ENG
Deutsch
Español
Subtitle
AUTO
DivX Subtitle
Western Italiano
Nederlands
Cesky
Using the Subtitle Language
1. Press the MENU button.
2. Press the √/® buttons to select Language Setup Page, then press the † or ENTER button.
3. Press the π/† buttons to select Subtitle, then press the ® or ENTER button.
4. Press the √/® buttons to select the desired language, then press the ENTER button.
– Select “Automatic” if you want the subtitle language to be the same as the language selected as the audio
language.
– Some discs may not contain the language you select ; in that case the disc will use its original language setting.
– The language is selected and the screen returns to the setup menu.
– To make the setup menu disappear, press the MENU but
ton.
-- Language Setup Page --
Player Menu
ENG
Automatic
English
Disc Menu
ENG
Audio
ENG
Français
Deutsch
Subtitle
AUTO
Español
DivX Subtitle
Western Italiano
Nederlands
28_ changing setup menu
-- Language Setup Page --
Player Menu
ENG
Western
Disc Menu
ENG
Central
Audio
ENG
Cyrillic
Subtitle
AUTO
Greek
DivX Subtitle
Western Turkish
Arabic
Hebrew
Setting Up the Audio options
Audio Options allow you to setup the audio device and sound
status settings depending on the audio system in use.
1. Press the MENU button.
2. Press the √/® buttons to select Audio Setup Page, then press the † or ENTER button.
3. Press the π/† buttons to select the desired item, then press the ® or ENTER button.
– To make the setup menu disappear, press the MENU but
ton.
-- Audio Setup Page --
Dolby Digital Out
PCM
MPEG2 Digital Output
PCM
Dynamic Compression
On PCM Down Sampling
On
Power On Music
On
-- Audio Setup Page --
Dolby Digital Out
PCM PCM
MPEG2 Digital Output
PCM Bitstream
Dynamic Compression
On PCM Down Sampling
On
Power On Music
On
❶ Dolby Digital Out
- PCM : Converts to PCM(2CH) audio.
- Bit stream : Outputs Dolby Digital via digital output.
Select Bit stream when connecting to a
Dolby Digital Decoder.
Note
- When playing discs that have MPEG Audio in
bit stream selection, the coaxial may not have any
audio output. This depends on the AV receiver.
❸ Dynamic Compression
- On : To select dynamic compression. This is useful for watching movies late at night, as it balances the loud and quiet portions of a disc.
- Off : To select the standard range.
❹ PCM Down Sampling
- On : Select this when the Amplifier connected to the player is not 96KHz compatible.
In this case, the 96KHz signals will be down converted to 48KHZ.
- Off : Select this when the Amplifier is connected to the player if it is 96KHz compatible. In this case, all signals will be output without any changes.
❺ Power music on
This menu is used to activate or deactivate the opening
sound when you turn on the DVD player.
- On : To turn On Start up music.
- Off : To turn Off Start up music.
Note
- Even when PCM Down sampling is Off.
- Some discs will only output down sampled audio through the digital outputs.
- To make the setup menu disappear, press the
MENU button.
HDMI
- If your TV is not compatible with compressed multi channel
formats (Dolby Digital, DTS, MPEG), you should set Digital
Audio to PCM.
- If your TV is not compatible with LPCM sampling rates over
48k Hz, you should set PCM Down sampling to on.
“DTS” and “DTS Digital Out” are trademarks of
Digital Theater Systems, Inc.
Setting Up the display options
Display options enable you to set various video functions of
the player.
1. Press the MENU button.
2. Press the √/® buttons to select Display Setup Page, then press the † or ENTER button.
3. Press the π/† buttons to select the desired item, then press the ® or ENTER button.
– To make the setup menu disappear, press the MENU but
ton.
-- Display Setup Page --
TV Aspect
Wide
Screen Message
On
Video Output
I-Scan
Black Level
Off
TV System
PAL
DivX VOD
❶ TV Aspect
Depending on a type of television you have, you may
want to adjust the screen setting (aspect ratio).
- 4:3 Pan&Scan : Select this for conventional size TVs
when you want to see the central portion of the 16:9
screen. (Extreme left and right side of movie picture
will be cut off.)
- 4:3 Letter Box : Select when you want to see the total
16:9 ratio screen DVD supplies, even though you
have a TV with a 4:3 ratio screen. Black bars will
appear at the top and bottom of the screen.
- 16:9 Wide : You can view the full 16:9 picture on your
wide screen TV.
-- Display Setup
TV Aspect
Screen Message
Video Output
Black Level
TV System DivX VOD
Page --
Wide 4:3 Pan&Scan
4:3 Letter Box
On
16:9 Wide
I-Scan
Off
PAL
❷ Screen Messages
Use to turn on-screen messages On or Off.
English _29
● changing setup menu
❷ MPEG2 Digital Output
- PCM : Converts to PCM (2CH) audio.
- Bit stream : Converts to MPEG-2 Digital Bit stream (5.1CH). Select Bit stream when using the Digital Audio Output.
Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol
are trademarks of Dolby Laboratories.
changing setup menu
❸ Video Output
Select Video Output.
To make the setup menu disappear, press OK.
- I-SCAN : Select when you want to use Video and
Component Interlace Out.
- P-SCAN : Select when you want to use Component
Progressive Out or HDMI.
❹ Black Level
Adjusts the brightness of the screen (On or
Off). It does not function in PAL mode.
❺ TV System
- NTSC : In case of using NTSC disc.
• If your TV system only has PAL-Video input, you must choose “PAL”. When you
choose “PAL”, Interlace output format is
PAL 60 Hz output.
• If your TV system only has NTSC, input you must choose “NTSC ”.
• If you set up the NTSC TV, HDMI output frame rate is 60 Hz.
• If your TV system only has NTSC-Video
input, you must choose “NTSC”. format is PAL 60 Hz output.
• If your TV system only has PAL input, you
must choose “PAL ”.
• If you set up the PAL TV, HDMI output frame rate is 50 Hz
-- Display Setup
TV Aspect
Screen Message
Video Output
Black Level
TV System DivX VOD
Note
- Consult your TV User's Manual to find out if your
TV supports Progressive Scan. If Progressive
Scan is supported, follow the TV User's Manual
regarding Progressive Scan settings in the Tv's
menu system.
- If Video Output is set incorrectly, the screen may
be blocked.
Setting Up the parental
control
- PAL : In case of using PAL disc.
DivX(R) Video On Demand
Your registration code is :
JGXJM B JF
http://www.divx.com/vod
Setting Up the Rating Level
The Parental Control function works in conjunction with DVDs
that have been assigned a rating, which helps you control the
types of DVDs that your family watches. There are up to 8
rating levels on a disc.
1. Press the MENU button.
2. Press the √/® buttons to select Parental Page, then press
the † or ENTER button.
Page --
Wide
On
I-Scan
Off
PAL
PAL
NTSC
-- Parental Page --
Parental
Password
3. Press the π/† buttons to select the Parental, then press the ® or ENTER button.
4. Press the π/† buttons to select the Rating Level you want, then press the ENTER button.
e.g) Setting up in KID SAFE
❻ DivX VOD
Select DivX VOD, then ® or ENTER button
Press OK to see the DivX Registration Number.
-- Display Setup
TV Aspect
Screen Message
Video Output
Black Level
TV System DivX VOD
30_ changing setup menu
Page --
Wide
On
I-Scan
Off
PAL
-- Parental Page --
Parental
Password
OK
2
3
4
5
6
7
8
G
PG
PG 13
PGR
R
NC 17
ADULT
Note
- To make the setup menu disappear, press the
MENU button.
For example, if you select the Kids Safe level,
discs that contain level 2 or higher will not play.
3. Press the π/† buttons to select the Password, then press the ® or ENTER button.
-- Parental Page --
Parental
Password
4. Select Change, then press ENTER button.
Password
0
1
2
3
4
5
6
7
8
9
-- Parental Page --
Parental
Password
Note
❶ KID SAFE
❷ G (General Audiences) : All Ages Admitted
❸ PG (Parental Guidance suggested) : Some material may not be suitable for young children.
❹ PG 13 (PG-13 Parents strongly cautioned) : Some material may be inappropriate for children
under 13.
❺ PGR (Parental Guidance Recommended) :
These are not necessarily unsuitable for children, but viewer discretion is advised, and parents and guardians are encouraged to supervise
younger viewers.
❻ R (Restricted) : Under 17 requires accompanying adult
❼ NC17 (NC-17) : No one 17 and under admitted.
❽ ADULT
Change
5. Fill in the blank box by pressing the √/®/π/† buttons to
enter your old password.
Old Password
New Password
Confirm Password
0
1
2
3
4
5
6
7
8
9
6. Please change password to other than 0000 to activate
parental control function. Enter your new password. Reenter the new password again.
Old Password
New Password
Confirm Password
Changing the Password
1. Press the MENU button.
2. Press the √/® buttons to select Parental Page, then press the † or ENTER button.
0
1
2
3
4
5
6
7
8
9
Note
- If you have forgotten your password, see "Forgot
Password" in the Troubleshooting Guide.
-- Parental Page --
Parental
Password
English _31
● changing setup menu
5. Fill in the blank box by pressing the √/®/π/†buttons to
enter your pasword. By default, password is set to 0000.
changing setup menu
Setting Up the HDMI
-- HDMI Page --
This Setting is used when the unit is connected by HDMI to
Display devices (TV, Projector, etc.).
1. Press the MENU button.
2. Press the √/® buttons to select HDMI Page, then press the † or ENTER button.
3. Press the π/† buttons to select HDMI, then press the ® or ENTER button.
- Auto : Auto resolution setting
HDMI
Auto
Anynet +(HDMI-CEC)
On
Picture Quality
BD Wise
Off
4. Set the Anynet+(HDMI-CEC) to “On”on your DVD Player., then press the ® or ENTER button.
- 480p/576p : 720 x 480, 720 x 576
-- HDMI Page --
- 720p : 1280 x 720
HDMI
Auto
Anynet +(HDMI-CEC)
On
- 1080i : 1920 x 1080
Picture Quality
BD Wise
- 1080p : 1920 x 1080
-- HDMI Page --
HDMI
Anynet +(HDMI-CEC)
Picture Quality
BD Wise
Auto Auto
On 576p
720p
1080i
Off
1080p
On
Off
Off
5.Set theAnynet+ function onyour SamsungTV.(Seeyour TV instruction manual for more information.).
• When you press Anynet+ button on the TV remote
control, the OSD to the right will appear.
DVP
Note
- The resolutions available for HDMI output depend
on the connected TV or projector. For details, see
the user's manual of your TV or projector.
- When the resolution is changed during playback,
it may take a few seconds for a normal image to
appear.
- If you have HDMI connected, better picture quality
will be provided when the output resolution is set
to 720p, 1080i or 1080p.
Setting Up Anynet+(HDMI-CEC)
View TV
®
Select Device
®
Record
®
Menu on Device
®
Device Operation
®
Receiver
®
: Off
Setup
Move
Exit
®
ENTER
You can operate the DVD Player by using the TV remote
control. These are buttons that can be used to operate
the DVD Player: , , , , , ,
Anynet+ is a function that can be used to operate this DVD
Player using a Samsung TV remote control. This is done by
connecting the DVD player to a SAMSUNG TV using an HDMI
Cable. (see pages 11-12) This is only available with SAMSUNG
TVs that support Anynet+.
and buttons, buttons.
1. Press the MENU button.
2. Press the √/® buttons to select HDMI Page, then press the † or ENTER button.
3. Press the π/† buttons to select Anynet+(HDMI-CEC), then
press the ® or ENTER button.
- Device Operation : Same as INFO button on the DVD
32_ changing setup menu
- Select Device : Use this option to select device which
you want to connect to your TV.
- Menu on Device : Same as MENU button on the DVD
Player remote control.
Player remote control.
Setting Up BD Wise
When the player is connected to a SAMSUNG TV which
supports “BD Wise”,you can enjoy optimized Picture Quality by
setting the “BD Wise” function as “On”.
1. Press the MENU button.
2. Press the √/® buttons to select HDMI Page, then press the † or ENTER button.
3. Press the π/† buttons to select BD Wise, then
press the ® or ENTER button. Press the π/† buttons to select On, then press the ENTER button.
-- HDMI Page --
Setting Up Picture Quality
1. Press the MENU button.
2. Press the √/® buttons to select HDMI Page, then press the † or ENTER button.
3. Press the π/† buttons to select Picture Quality, then
press the ® or ENTER button.
HDMI
Auto
Anynet +(HDMI-CEC)
On
Picture Quality
BD Wise
Off
-- HDMI Page --
-- HDMI Page --
HDMI
Auto
Anynet +(HDMI-CEC)
On
Auto
Anynet +(HDMI-CEC)
On
Picture Quality
BD Wise
Picture Quality
BD Wise
HDMI
On
Off
On
Off
-- HDMI Page --
-- Picture Quality Page --
Brightness
Level 3
Contrast
Level 3
Color Saturation
Level 3
Note
- Brightness : Level 1 ~ Level 5
- Contrast : Level 1 ~ Level 5
- Color Saturation : Level 1 ~ Level 5
BD Wise
Anynet +(HDMI-CEC)
On
Picture Quality
BD Wise
4. Press the π/† buttons to select Picture Quality Page, then
press the ® or ENTER button.
-- Picture Quality Page --
Brightness
Level 3 Level
Contrast
Level 3 Level
Level
Color Saturation
Level 3
Level
Level
HDMI
On
Note
- This option can be changed only when TV support BD Wise.
How to turn Off the BD Wise
1
2
3
4
5
If you wish to change to other resolution when “BD Wise On”,
Please choose a method between these two as follows :
Method 1
1. Press the MENU button.
2. Press the √/® buttons to select HDMI Page, then press the † or ENTER button.
3. Press the π/† buttons to select HDMI, then
press the ® or ENTER button. Press the π/† buttons to select resolution you wish to use, then press the ENTER
button.
English _33
● changing setup menu
Note
- While watching TV, your TV screen will change to
the play screen when you press the PLAY button
of the DVD player.
- If you play a DVD when the TV power is off, the
TV will power On.
- If you turn the TV off, the DVD player will power
off automatically.
- If you change from HDMI to other sources
(Composite, Component, ... etc) while a DVD
Player will stop playing.
changing setup menu
-- HDMI Page --
HDMI
Auto Auto
On BD Wise
576p
720p
On
1080i
1080p
Anynet +(HDMI-CEC)
Picture Quality
BD Wise
- Please choose “Yes” to continue, otherwise choose “No” to keep current setting.
Do you want to turn off BD Wise Mode
and change to selected Resolution?
No
Yes
Method 2
1. Press the MENU button.
2. Press the √/® buttons to select HDMI Page, then press the † or ENTER button.
3. Press the π/† buttons to select BD Wise, then
press the ® or ENTER button. Press the π/† buttons to select Off, then press the ENTER button.
- The HDMI resolution will be changed to maximum resolution supported by your TV.
-- HDMI Page --
HDMI
BD Wise
Anynet +(HDMI-CEC)
On
Picture Quality
BD Wise
On
-- HDMI Page --
HDMI
BD Wise
Anynet +(HDMI-CEC)
On
Picture Quality
BD Wise
On
-- HDMI Page --
HDMI
Auto
Anynet +(HDMI-CEC)
On
Picture Quality
BD Wise
34_ changing setup menu
Off
On
Off
Note
• It is recomended to set the "BD Wise" to "Off".
In case of playback JPEG image file bigger than
720x480 pixel size.
reference
Firmware upgrade
Introduction
the performance of this unit to the latest status, through
Samsung Internet Site (www.samsung.com).
Because the specially new mpeg4 codec continues and it is
appearing. What improvements are made depends on the
upgrade software you are using as well as the software that
your DVD-player contained before the upgrade.
How to make an upgrade disc
Write the downloaded file onto a blank CD-R or CD-RW disc,
using the following settings :
1. You have to download a new file through Download Center
of Samsung Internet Site (www.samsung.com).
2. Write the file to Disc using CD-RW of your computer.
Firmware upgrade
menu starts
- During the firmware upgrade process, the tray will open.
Please remove the disc and wait for about 2 minutes.
- If the DVD player was successfully updated, the disc tray will close and the unit will turn off and on.When the unit turns on, the Select Menu Language screen will appear.
3. Press the π/† buttons to select the desired language, and then press the ENTER button.
Select Menu Language
English
Français
Deutsch
Español
Italiano
Note
- File system CD-ROM
- Character set ISO 9660
- Finalized, single session
- Write speed low
Nederlands
Upgrade procedure
1. Open the disc tray of your DVD-Player.
Place the burned disc on the tray. Close the tray.
The Firmware upgrade screen will appear.
Note
- If the “Select Menu Language” doesn’t appear,
please contact Samsung Customer Service.
- Do not press any button or unplug the power cord
during the upgrade.
- The upgrade procedure may change, refer to the
web site (www.samsung.com).
Upgrade file detected
Curent version: 07.01.03.08.H1080XAA
Update version: 07.02.03.09.H1080XAA
Upgrade ?
Press Play to start
Firmware upgrade
menu appears
2. Press enter or play upgrade
- Press any other button on the remote control to cancel the upgrade and eject the dics (eg.π etc).appear.
Upgrade file detected
Curent version: 07.01.03.08.H1080XAA
Update version: 07.02.03.09.H1080XAA
Upgrade ?
Press Play to start
File copying
Firmware upgrade
starts
English _35
● reference
Samsung will often support the software upgrade to improve
Upgrade file detected
Curent version: 07.01.03.08.H1080XAA
Update version: 07.02.03.09.H1080XAA
Upgrade ?
Press Play to start
Upgrade
reference
Troubleshooting
Before requesting service (troubleshooting), please check the following.
Problem
Action
Page
No operations can be
performed with the
remote control.
• Check the batteries in the remote control.They may need replacing.
• Operate the remote control at a distance of no more than 20 feet.
• Remove batteries and hold down one or more buttons for several
minutes to drain the microprocessor inside the remote control to reset
it. Reinstall batteries and try to operate the remote control again.
P3
Disc does not play.
• Ensure that the disc is installed with the label side facing up.
• Check the region number of the DVD.
P5
The
icon appears
on screen.
• The features or action cannot be completed at this time because:
1. The DVD’s software restricts it.
2. The DVD’s software doesn’t support the feature (e.g., angles).
3. The feature is not available at the moment.
4. You’ve requested a title or chapter number or search time that is out of
range.
Disc Menu doesn’t
appear
• Check if the disc has a Menu
Play mode differs
from the Setup Menu
selection.
• Some of the functions selected in the Setup Menu may not work
properly if the disc is not encoded with the corresponding function.
P27~33
The screen ratio
cannot be changed.
Ŗ6JG5ETGGP4CVKQKUſZGFQP[QWT&8&U
P29~30
No audio.
• Make sure you have selected the correct Digital Output in the Audio
Options Menu.
P28~29
The screen is blocked
• Press the
button (on the front panel) for more than 5 seconds with no disc
inside. All settings will revert to the factory settings
Forgot password
• Press the
button (on the panel) for more than 5 seconds with no disc inside.
All settings including the password will revert to the factory settings. Don't use
this unless absolutely necessary.
+H[QWGZRGTKGPEGQVJGT
problems.
Ŗ)QVQVJGEQPVGPVUCPFſPFVJGUGEVKQPQHVJGKPUVTWEVKQPDQQMVJCV
EQPVCKPUVJGGZRNCPCVKQPUTGICTFKPIVJGEWTTGPVRTQDNGOCPFHQNNQYVJG
procedure once again.
• If the problem still cannot be solved, please contact your nearest
authorized service center.
The picture is noisy or
distorted
• Make sure that the disc is not dirty or scratched.
• Clean the disc.
No HDMI output.
• Check the Video output is HDMI enabled.
• Check the connection between the TV and the HDMI jack of DVD player.
• See if the TV supports this 480p/576p/720p/1080i/1080p DVD player
P11~12
Abnormal HDMI output
screen.
• If snow noise appears on the screen, it means that TV does not support
HDCP (High-bandwidth Digital Content Protection).
P11~12
HDMI output Jitter
• Check your TV system setup correctly.
• The screen Jitter phenomenon may occur when frame rate is converted
HTQO*\VQ*\HQT2KR*&/+
*KIJ&GſPKVKQP/WNVKOG
dia Interface) Output.
• Please refer to the user’s manual of your TV.
P32~33
36_ reference
P15
P30~31
P2
Specifications
General
Power Requirements
AC 110-240V ~ 50/60 Hz
Power Consumption
8W
Weight
+5°C to +35°C
Operating Humidity Range
10 % to 75 %
DVD
(DIGITAL VERSATILE DISC)
Disc
Video
Output
Reading Speed : 3.49 ~ 4.06 m/sec.
Approx. Play Time
(Single Sided, Single Layer Disc) : 135 min.
CD : 12Cm
(COMPACT DISC)
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min.
CD : 8Cm
(COMPACT DISC)
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 20 min.
Composite Video
1 channel : 1.0 Vp-p (75 Ω load)
Component Video
Y : 1.0 Vp-p (75 Ω load)
Pr : 0.70 Vp-p (75 Ω load)
Pb : 0.70 Vp-p (75 Ω load)
HDMI
Audio
Output
264.5mm (W) X 248mm (D) X 50.5mm (H)
Operating Temperature Range
Maximun Output Level
Digital Audio Output
*Frequency Response
● reference
Dimensions
0.976 Kg
480p/576p. 720p. 1080i. 1080p
2Vrms
Coaxial terminal (S/PDIF)
20Hz~20kHz
*: Nominal specification
Note
- Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
- Weight and dimensions are approximate.
English _37
UNITED KINGDOM
This Samsung product is warranted for the period of
twelve (12) months from the original date of
purchase, against defective materials and
workmanship. In the event that warranty service is
required, you should return the product to the retailer
from whom it was purchased.
However, Samsung Authorised Dealers and
Authorised Service Centres in other EC Countries will
comply with the warranty on the terms issued to
purchasers in the country concerned.
In case of difficulty, details of our Authorised Service
Centres are available from:
Samsung Electronics U.K. Ltd.
Customer Care Centre PO Box 17243 Edinburgh,
EH11 4YB United Kingdom
United Kingdom
Tel : 0845 SAMSUNG (7267864)
Fax : 0845 650 8080
Web : www.samsung.com
EIRE
Tel : 0818 717 100
Fax : +44 (0)131 202 0630
Web : www.samsung.com
„ WARRANTY CONDITIONS
1. The warranty is only valid if, when warranty service
is required, the warranty card is fully and properly
completed and is presented with the original invoice
or sales slip or confirmation, and the serial number
on the product has not been defaced.
2. Samsung’s obligations are limited to the repair or,
at its discretion, replacement of the product or the
defective part.
3. Warranty repairs must be carried out by Authorised
Samsung Dealers or Authorised Service Centres.
No re-imbursement will be made for repairs carried
out by non Samsung Dealers and, any such repair
work and damage to the products caused by such
repair work will not be covered by this warranty.
EIRE
4. This product is not considered to be defective
in materials nor workmanship by reason that it
requires adaptation in order to conform to national
or local technical or safety standards in force in
any Country other than the one for which the
product was originally designed and manufactured.
This warranty will not cover, and no re-imbursement will be made for such adaptation nor any
damage which may result.
5. This warranty covers none of the following:
a) Periodic check ups, maintenance and repair or
replacement of parts due to normal wear and
tear.
b) Cost relating to transport, removal or installation
of the product.
c) Misuse, including the faiure to use this product
for its normal purposes or incorrect installation.
d) Damage caused by Lightning, Water, Fire, Acts
of God, War, Public Disturbances, incorrect
mains voltage, improper ventilation or any other
cause beyond the control of Samsung.
6. This warranty is valid for any person who legally
acquired possession of the product during the
warranty period.
7. The consumers statutory rights in any applicable
national legislation whether against the retailer
arising from the purchase contract or otherwise
are not affected by this warranty. Unless there is
national legislation to the contrary, the rights under
this warranty are the consumers sole rights and
Samsung, its subsidiaries and distributors shall not
be liable for indirect or consequential loss or any
damage to records, compact discs, videos or audio
taper or any other related equipment or material.
SAMSUNG ELECTRONICS (U.K.) LTD.
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.
Region
North America
Latin America
Country
CANADA
MEXICO
U.S.A
ARGENTINE
BRAZIL
CHILE
NICARAGUA
HONDURAS
COSTA RICA
ECUADOR
EL SALVADOR
GUATEMALA
JAMAICA
PANAMA
PUERTO RICO
REP. DOMINICA
TRINIDAD & TOBAGO
VENEZUELA
COLOMBIA
BELGIUM
CZECH REPUBLIC
DENMARK
FINLAND
FRANCE
Europe
CIS
Asia Pacific
Middle East &
Africa
GERMANY
HUNGARY
ITALIA
LUXEMBURG
NETHERLANDS
NORWAY
POLAND
PORTUGAL
SLOVAKIA
SPAIN
SWEDEN
U.K
EIRE
AUSTRIA
SWITZERLAND
RUSSIA
KAZAKHSTAN
UZBEKISTAN
KYRGYZSTAN
TADJIKISTAN
UKRAINE
LITHUANIA
LATVIA
ESTONIA
AUSTRALIA
NEW ZEALAND
CHINA
HONG KONG
INDIA
INDONESIA
JAPAN
MALAYSIA
PHILIPPINES
SINGAPORE
THAILAND
TAIWAN
VIETNAM
TURKEY
SOUTH AFRICA
U.A.E
Contact Center 1-800-SAMSUNG(726-7864)
01-800-SAMSUNG(726-7864)
1-800-SAMSUNG(726-7864)
0800-333-3733
0800-124-421, 4004-0000
800-SAMSUNG(726-7864)
00-1800-5077267
800-7919267
0-800-507-7267
1-800-10-7267
800-6225
1-800-299-0013
1-800-234-7267
800-7267
1-800-682-3180
1-800-751-2676
1-800-SAMSUNG(726-7864)
0-800-100-5303
01-8000112112
02 201 2418
800-726-786 (800 - SAMSUNG)
70 70 19 70
030-6227 515
3260 SAMSUNG (€ 0,15/Min)
08 25 08 65 65 (€ 0,15/Min)
01805 - SAMSUNG(726-7864 € 0,14/Min)
06-80-SAMSUNG(726-7864)
800-SAMSUNG(726-7864)
02 261 03 710
0900-SAMSUNG (726-7864 € 0,10/Min)
815-56 480
0 801 801 881, 022-607-93-33
80820-SAMSUNG(726-7864)
0800-SAMSUNG(726-7864)
902-1-SAMSU(72678)
0771-400 200
0845 SAMSUNG (7267864)
0818 717 100
0800-SAMSUNG(726-7864)
0800-SAMSUNG(726-7864)
8-800-555-55-55
8-10-800-500-55-500
8-10-800-500-55-500
00-800-500-55-500
8-10-800-500-55-500
8-800-502-0000
8-800-77777
8000-7267
800-7267
1300 362 603
0800 SAMSUNG (0800 726 786)
800-810-5858, 400-810-5858, 010-6475 1880
3698-4698
3030 8282, 1800 110011, 1-800-3000-8282
0800-112-8888
0120-327-527
1800-88-9999
1800-10-SAMSUNG(726-7864)
1800-SAMSUNG(726-7864)
1800-29-3232, 02-689-3232
0800-329-999
1 800 588 889
444 77 11
0860-SAMSUNG(726-7864 )
800-SAMSUNG (726-7864), 8000-4726
Web Site
www.samsung.com/ca
www.samsung.com/mx
www.samsung.com/us
www.samsung.com/ar
www.samsung.com/br
www.samsung.com/cl
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com.co
www.samsung.com/be
www.samsung.com/cz
www.samsung.com/dk
www.samsung.com/fi
www.samsung.com/fr
www.samsung.de
www.samsung.com/hu
www.samsung.com/it
www.samsung.com/lu
www.samsung.com/nl
www.samsung.com/no
www.samsung.com/pl
www.samsung.com/pt
www.samsung.com/sk
www.samsung.com/es
www.samsung.com/se
www.samsung.com/uk
www.samsung.com/ie
www.samsung.com/at
www.samsung.com/ch
www.samsung.ru
www.samsung.com/kz_ru
www.samsung.com/kz_ru
www.samsung.ua
www.samsung.lt
www.samsung.com/lv
www.samsung.ee
www.samsung.com/au
www.samsung.com/nz
www.samsung.com/cn
www.samsung.com/hk
www.samsung.com/in
www.samsung.com/id
www.samsung.com/jp
www.samsung.com/my
www.samsung.com/ph
www.samsung.com/sg
www.samsung.com/th
www.samsung.com/tw
www.samsung.com/vn
www.samsung.com/tr
www.samsung.com/za
www.samsung.com/ae
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger,
headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible
harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of
waste and recycle them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for
details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its
electronic accessories should not be mixed with other commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
of with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb
indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66. If
batteries are not properly disposed of, these substances can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste
and recycle them through your local, free battery return system.
AK68-01754K(02)