ADJ Fusion Tri FX Bar Operating instructions

Fusion Tri FX Bar Introduction
Unpacking: Thank you for purchasing the Fusion Tri FX Bar by Ameri-
can DJ®. Every Fusion Tri FX Bar has been thoroughly tested and has
been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the
carton appears to be damaged, carefully inspect your fixture for any
damage and be sure all accessories necessary to operate the unit has
arrived intact. In the case damage has been found or parts are missing, please contact our toll free customer support number for further
instructions. Do not return this unit to your dealer without first contacting customer support.
Introduction: The Fusion Tri FX Bar is part of American DJ’s continu-
ing pursuit for creating high quality affordable intelligent fixtures. The
Fusion Tri FX Bar is a DMX intelligent LED display fixture. This unit
can be used as a stand alone, or in a Master/Slave configuration. The
unit three operating modes; sound active mode, show mode, and DMX
control mode. This fixture is a great piece for retail stores, displays,
mood, architectural, interior and exterior decoration, and clubs.
Customer Support: American DJ® provides a toll free customer sup-
port line, to provide set up help and to answer any question should you
encounter problems during your set up or initial operation. You may
also visit us on the web at www.americandj.com for any comments or
suggestions. Service Hours are Monday through Friday 8:00 a.m. to
4:30 p.m. Pacific Standard Time.
Voice:
(800) 322-6337
Fax: (323) 582-2941
E-mail: support@americandj.com
To purchase parts online visit http://parts.americandj.com
Warning! To prevent or reduce the risk of electrical shock or fire, do
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
User Instructions
attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact
American DJ®.
PLEASE recycle the shipping carton when ever possible.
Rev. 3/14
©American
DJ Supply® - www.americandj.com - Fusion Tri FX Bar - Page 2
Fusion Tri FX Bar General Instructions
To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual with the unit, for future reference.
Fusion Tri FX Bar •
•
•
•
•
•
•
•
Features
Electronic Dimming 0-100%
Built in Microphone
DMX-512 protocol
Eight DMX Channels
Optional 12 Degree Lenses
3 Operating Modes - Sound Active, Show Mode, or DMX Control
UC3 Remote Control Compatiable (Not Included)
Power Cord Daisy Chaining
Fusion Tri FX Bar Warranty Registration
The Fusion Tri FX Bar carries a 2 year (730 days) limited warranty.
Please fill out the enclosed warranty card to validate your purchase
and warranty. You may also register your product online at www.
americandj.com. All returned service items whether under warranty or
not, must be freight pre-paid and accompany a return authorization
(R.A.) number. If the unit is under warranty you must provide a copy
of your proof of purchase invoice. Please contact American DJ® customer support for a R.A. number.
©American
DJ Supply® - www.americandj.com - Fusion Tri FX Bar - Page 3
Fusion Tri FX Bar
Safety Precautions
•To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture
•Do not spill water or other liquids into or on to your unit.
•Be sure that the local power outlet match that of the required volt-
age for your unit.
•Do not attempt to operate this unit if the power cord hasbeen
frayed or broken. Do not attempt to remove or break off the ground
prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short.
•Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user serviceable parts inside.
•Never operate this unit when it’s cover is removed.
•Never plug this unit in to a dimmer pack
•Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall.
•Do not attempt to operate this unit, if it becomes damaged.
•This unit is intended for indoor use only, use of this product out`
doors voids all warranties.
•During long periods of non-use, disconnect the unit’s main power.
•Always mount this unit in safe and stable matter.
•Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them, paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 15 for cleaning details.
•Heat -The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.
•The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a marked change in performance.
©American
DJ Supply® - www.americandj.com - Fusion Tri FX Bar - Page 4
POWER
Fusion Tri FX Bar
Set Up
Fusion Tri FX Bar
Notice: Be sure to follow figures two and three when making your own
automatic voltage switch, which will auto sense the voltage when it
is plugged into the power source. With this switch there is no need
to worry about the correct power voltage, this unit can be plugged in
anywhere.
cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
DMX-512: DMX is short for Digital Multiplex. This is a universal proSOUND
REMOTE
CONTROL
INPUT
INPUT
OUTPUT
COMMON
1
REMOTE
CONTROL
SOUND
3
DMX -
Data Cable (DMX Cable) Requirements (For DMX Operation):
2
The Fusion Tri FX Bar can be controlled via DMX-512 protocol. The Fusion
Tri FX Bar eight channel DMX unit. The DMX address is set on the rear
panel of the Fusion Tri FX Bar. Your unit and your DMX controller require
a standard 3-pin XLR connector for data input and data output (Figure
1). If you are making your own cables, be sure to
use standard two conductor shielded cable (This
cable may be purchased at almost all pro sound
and lighting stores). Your cables should be made
with a male and female XLR connector on either
end of the cable. Also remember that DMX cable
must be daisy chained and can not be split.
Figure 1
©American DJ® - www.americandj.com - Fusion Tri FX Bar - Page 5
1
DMX512 OUT
3-PIN XLR
INPUT
2
1 Ground
DMX +
3
OUTPUT
3
DMX -
1
2
SOUND
XLR Female Socket
XLRINPUT
Male Socket
2 Cold
2 Cold
1 Ground
DMX512 IN
3-PIN XLR
REMOTE
CONTROL
INPUT
INPUT
3
Figure 2
OUTPUT
1
2
Termination redu
avoids signal tra
and interference.
to connect a DMX
120 Ohm 1/4 W)
and PIN 3 (DMX
XLR Pin Configuration
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
3 Hot
Figure 3
POWER
3-PIN XLR
Set Up
DMX512
DMX+,DMX-,COMMON
Power Supply: The American DJ® Fusion Tri FX Bar contains a
tocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a single
controller, as long as all fixtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several
DMX512
DMX fixtures try to use the shortest cable path
possible.
The order
DMX+,DMX-,COMMON
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address
COMMON 1
DMX +
to that unit, no matter where it is located in the
DMX
DMX512
OUT chain.
POWER
3 Hot
Pin 3 = Data True (positive)
POWER
POWER
Special Note: Line Termination. When longer runs of cable are
3
1
2
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
Termination reduces signal errors and
DMX512 IN
3-PIN XLR
3
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
Figure 4
5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR
connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures
may be implemented in a 3-pin XLR DMX line. When inserting standard
5-pin XLR connectors in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor
3-Pin XLR Female (Out)
5-Pin XLR Male (In)
Ground/Shield
Pin 1
Pin 1
Data Compliment (- signal)
Pin 2
Pin 2
Data True (+ signal)
Pin 3
Pin 3
Not Used
Do Not Use
Not Used
Do Not Use
©American
DJ Supply® - www.americandj.com - Fusion Tri FX Bar - Page 6
Fusion Tri FX Bar
System Menu
Fusion Tri FX Bar
System Menu
On-Board System Menu. The Fusion Tri FX Bar comes with an easy
to navigate system menu. This next section will detail the functions of
each command in the system menu. Please read the next section
thoroughly!
To access the main menu press the MENU button. Tap the UP or
DOWN buttons until you reach function you wish to change. When you
reach the function you wish to change press the ENTER button. When
a function is selected use the UP or DOWN buttons to change the function settings. Once your changes are made press the ENTER button,
and then press and hold the MENU button for at least three seconds
to confirm and lock the change into the system memory. If the MENU
button is not pressed and held within eight seconds the fixture will
automatically confirm and lock the change into the system memory. To
exit without making any changes press the MENU button.
ADDR - DMX Address Setting via control board 1. Tap the MENU button until “ADDR” is displayed, press ENTER.
2. “X” will now be displayed, “X” represents the displayed address.
Press the UP or DOWN buttons to find your desired address.
3. Press ENTER to confirm, and then press and hold the MENU button
for at least three seconds to assign.
SLND - This will let you set unit as a master or slave in a
master/slave configuration.
1. Tap the MENU button until “SLND” is displayed, press ENTER.
Either “MAST”, “SL 1” or “SL 2” will be displayed.
2. Tap the UP or DOWN buttons until your desired setting is displayed, press ENTER to confim.
NOTE: In a Master/Slave configuration you can make one fixture the
Master and then set the next fixture to “SL 2”, the fixtures will now
have contrast movement to each other.
SHND: SH 0 - SH 16 - Show modes 0 - 16 (Factory programs). You can run show mode with sound active mode off
©American
DJ Supply® - www.americandj.com - Fusion Tri FX Bar - Page 7
©American
DJ Supply® - www.americandj.com - Fusion Tri FX Bar - Page 8
Fusion Tri FX Bar
or on.
System Menu
Fusion Tri FX Bar
System Menu
three seconds to confirm.
1. Tap the MENU button until “SHND” is displayed, press ENTER.
2. “Sh X” will now be displayed, “X” representing a number between 116. Shows 1-16 are preset shows, while “Sh 0” is random show. Press
the UP or DOWN buttons to find your desired show.
3. Press ENTER, and then press and hold the MENU button for at least
3 seconds to confirm.
SOUN - In this mode you can run the unit in sound active
mode
1. Tap the MENU button until “SOUN” is displayed, press ENTER.
2. Either “ON” or “OFF” will now be displayed. Press the UP or DOWN
buttons to select one or the other.
DISP - This will “flip” the LED display
1. Tap the MENU button until “dISP” is displayed, press ENTER.
2. Either “dISP” or “dSIP” will now be displayed. Press the UP or DOWN
buttons to select one or the other.
3. Press ENTER, and then press and hold the MENU button for at least
three seconds to confirm.
MANU - With this function you can manually test the individual features.
1. Tap the MENU button until “MANU” is displayed, press ENTER.
3. When you have made your selection, press the ENTER, and then
press and hold the MENU button for at least 3 seconds to confirm.
2. Press the UP or DOWN buttons to find and manually test the individual features. Press ENTER when you have found the feature you
want to test.
BLND - This will control blackout
TEST - This function will run a self test program.
1. Tap the MENU button until “bLNd” is displayed, press ENTER.
1. Tap the MENU button until “TEST” is displayed, press ENTER.
2. Either “YES” or “NO” will now be displayed. Press the UP or DOWN
buttons to select one or the other.
2. The fixture will now run a self test.
3. Press ENTER, and then press and hold the MENU button for at least
three seconds to confirm.
LED - With this function the LED display will turn off after 2
minutes.
1. Tap the MENU button until “LED” is displayed, press ENTER.
2. Either “ON” or “OFF” will now be displayed. Press the UP or DOWN
buttons to select “ON” to keep the LED display on at all times, or “OFF”
to allow the LED display to turn off after 2 minutes. Press any button to
turn on the LED display again.
3. Press ENTER, and then press and hold the MENU button for at least
©American
DJ Supply® - www.americandj.com - Fusion Tri FX Bar - Page 9
FHRS - With this function you can display the running time
of the unit.
1. Tap the MENU button until “FHRS” is displayed, press ENTER.
2. The running time of the fixture will now be displayed. Press MENU
to exit.
VER - This will display the software version
1. Tap the MENU button until “VER” is displayed. Press the ENTER
button and the software vesion will be displayed.
2. Press the MENU button to leave this function.
©American
DJ Supply® - www.americandj.com - Fusion Tri FX Bar - Page 10
Fusion Tri FX Bar
Operation
Universal DMX Control: This function allows you to use a Elation®
universal DMX-512 controller to control the chases and patterns, dimmer and strobe. A DMX controller allows you to create unique programs tailored to your individual needs.
1. The Fusion Tri FX Bar is a 8 DMX channel unit. See page 13 for a detailed description of the DMX traits.
2. To control your fixture in DMX mode, follow the set-up procedures
on pages 5-6 as well as the set-up specifications that are
included with your DMX controller.
3. Use the controller’s faders to control the various DMX fixture traits.
4. This will allow you to create your own programs.
5. Follow the instructions on page 8 to set the DMX address.
6. For longer cable runs (more than a 100 feet) use a terminator on the last fixture.
7. For help operating in DMX mode consult the manual included with your DMX controller.
Master-Slave Operation: This function will allow you to link up to 16
units together and operate without a controller. In Master-Slave operation one unit will act as the controlling unit and the others will react to
the controlling units programs. Any unit can act as a Master or as a
Slave.
1. Using standard XLR microphone cables, daisy chain your units together via the XLR connector on the rear of the units. Remem-
ber the Male XLR connector is the input and the Female XLR connector is the output. The first unit in the chain (master) will use the female XLR connector only - The last unit in the chain will use the male XLR connector only. For longer cable runs we suggest a terminator at the last fixture.
2. On the Master unit find your desired show or choose sound act- tive mode and set that by pressiing the ENTER button.
3. On the slave units tap the MENU button until “SLND” is display-
ed, and Press ENTER.
4. The slave units will now follow the Master unit.
5. The optional UC3 Controller (not included) may be used to con-
trol different functions including blackout.
©American
DJ Supply® - www.americandj.com - Fusion Tri FX Bar - Page 11
Fusion Tri FX Bar
Operation
Sound Active Mode: This mode allows a single unit or several units
linked together, to run to the beat of the music.
1. Tap the MENU button until “SOUN” is displayed, and press ENTER.
2. Tap the UP or DOWN buttons until “ON” is displayed and press ENTER, and then press and hold the MENU button to confirm.
3. The optional UC3 Controller (not included) may be used to con-
trol different functions including blackout.
Show Mode: This mode allows a single unit or several units linked
together, to run your desired factory show.
1. Tap the MENU button until “SHND” is displayed, and press ENTER.
2. Tap the UP or DOWN buttons until you find your desired show, and press ENTER, and then press and hold the MENU button to confirm.
3. The optional UC3 Controller (not included) may be used to con-
trol different functions including blackout.
Fusion Tri FX Bar
Power Cord Daisy Chaining
With this feature you can connect the fixtures to one another
using the IEC input and output sockets. The quantity that can be
connected is 19 fixtures maximum. After 19 fixtures you will need
to use a new power outlet. They must be the same fixtures. DO
NOT mix fixtures.
Fusion Tri FX Bar
UC3 Control
Stand By
Blackout the unit
Function
1. LED Sound strobe
Select show
2. Spot Sound strobe
1-16
Mode
©American
Sound (LED OFF)
LED ON
DJ Supply® - www.americandj.com - Fusion Tri FX Bar - Page 12
Fusion Tri FX Bar
Channel
1
2
3
4
©American
Value
DMX Channels & Functions
Function
0-9
10 - 19
20 - 29
30 - 39
40 - 49
50 - 59
60 - 69
70 - 79
80 - 89
90 - 99
100 - 109
110 - 119
120 - 129
130 - 139
140 - 149
150 - 159
160 - 169
170 - 179
180 - 249
250 - 255
CHASES & STROBE
OFF
CHASE 1
CHASE 2
CHASE 3
CHASE 4
CHASE 5
CHASE 6
CHASE 7
CHASE 8
CHASE 9
CHASE 10
CHASE 11
CHASE 12
CHASE 13
CHASE 14
CHASE 15
CHASE 16
CHASE 17
STROBING SLOW - FAST
ON
0-9
10 - 49
50 - 89
90 - 129
130 - 169
170 - 209
210 - 249
250 - 255
TRI LED PINSPOT 1
OFF
COLOR 1
COLOR 2
COLOR 3
COLOR 4
COLOR 5
COLOR 6
COLOR 7
0 - 255
RED LED 0% - 100%
0-9
10 - 49
50 - 89
90 - 129
TRI LED PINSPOT 2
OFF
COLOR 1
COLOR 2
COLOR 3
DJ Supply® - www.americandj.com - Fusion Tri FX Bar - Page 13
Fusion Tri FX Bar
Channel
4
5
6
7
8
©American
Value
130 - 169
170 - 209
210 - 249
250 - 255
0 - 255
0-9
10 - 49
50 - 89
90 - 129
130 - 169
170 - 209
210 - 249
250 - 255
0 - 255
0-9
10 - 49
50 - 89
90 - 129
130 - 169
170 - 209
210 - 249
250 - 255
DMX Channels & Functions
Function
TRI LED PINSPOT 2
COLOR 4
COLOR 5
COLOR 6
COLOR 7
GREEN LED 0% - 100%
TRI LED PINSPOT 3
OFF
COLOR 1
COLOR 2
COLOR 3
COLOR 4
COLOR 5
COLOR 6
COLOR 7
BLUE LED 0% - 100%
TRI LED PINSPOT 4
OFF
COLOR 1
COLOR 2
COLOR 3
COLOR 4
COLOR 5
COLOR 6
COLOR 7
DJ Supply® - www.americandj.com - Fusion Tri FX Bar - Page 14
Fusion Tri FX Bar
12 Degree Lens
To switch to the 12 Degree lens, simply unscrew and remove the
phillips screws located above and below the lenses. After the screws
have been removed, remove frame that holds the lens in place.
Remove the lens and install the 12 Degree lens. Put the lens frame
back into place, and replace the phillips screws to secure the frame
and lens.
Fusion Tri FX Bar
Fuse Replacement
Locate and remove the unit’s power cord. Once the cord has been
removed located the fuse holder located inside the power socket.
Insert a flat-head screw driver into the power socket and gently pry out
the fuse holder. Remove the bad fuse and replace with a new one. The
fuse holder has å built-in socket for a spare fuse be sure not to confuse
the spare fuse with active fuse.
Fusion Tri FX Bar
Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be carried out periodically to optimize light
output.
1. Use a soft cloth to wipe down the outside casing.
Cleaning frequency depends on the environment in which the fixture
operates (i.e. smoke, fog residue, dust, dew).
Fusion Tri FX Bar
Trouble Shooting
Listed below are a few common problems the user may encounter,
with solutions.
Unit not responding to DMX:
1. Check that the DMX cables are connected properly and are wired correctly (pin 3 is “hot”; on some other DMX devices pin 2 may be ‘hot’). Also, check that all cables are connected to the right connectors; it does matter which way the inputs and outputs are connected.
Unit does not respond to sound:
1. Quiet or high pitched sounds will not activate the unit.
©American
DJ Supply® - www.americandj.com - Fusion Tri FX Bar - Page 15
Fusion Tri FX Bar
Warranty
MANUFACTURER’S LIMITED WARRANTY
A. American DJ, Inc. hereby warrants, to the original purchaser, American DJ and American
Audio products to be free of manufacturing defects in material and workmanship for a prescribed
period from the date of purchase (see specific warranty period on reverse). This warranty shall be
valid only if the product is purchased within the United States of America, including possessions
and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought.
B.
For warranty service you must obtain a Return Authorization number (RA#) before
sending back the product. Contact American DJ, Inc. Service Department at 800-322-6337. Send
the product only to the American DJ, Inc. factory. All shipping charges must be pre-paid. If the
requested repairs or service (including parts replacement) are within the terms of this warranty,
American DJ, Inc. will pay return shipping charges only to a designated point within the United
States. If the entire instrument is sent, it must be shipped in it’s original package. No accessories
should be shipped with the product. If any accessories are shipped with the product, American DJ,
Inc. shall have no liability whatsoever for loss of or damage to any such accessories, nor for the
safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is
modified in any manner which American DJ, Inc. concludes, after inspection, affects the reliability
of the product; if the product has been repaired or serviced by anyone other than the American DJ,
Inc. factory unless prior written authorization was issued to purchaser by American DJ, Inc.; if the
product is damaged because not properly maintained as set forth in the instruction manual.
D.
This is not a service contract, and this warranty does not include maintenance, cleaning
or periodic check-up. During the period specified above, American DJ, Inc. will replace defective
parts at its expense with new or refurbished parts, and will absorb all expenses for warranty service
and repair labor by reason of defects in material or workmanship. The sole responsibility of American DJ, Inc. under this warranty shall be limited to the repair of the product, or replacement thereof,
including parts, at the sole discretion of American DJ. All products covered by this warranty were
manufactured after January 1, 1990, and bear identifying marks to that effect.
E.
American DJ, Inc. reserves the right to make changes in design and/or improvements
upon its products without any obligation to include these changes in any products theretofore manufactured. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above. Except to the extent prohibited by applicable law, all
implied warranties made by American DJ, Inc. in connection with this product, including warranties
of merchantability or fitness, are limited in duration to the warranty period set forth above. And no
warranties, whether expressed or implied, including warranties of merchantability or fitness, shall
apply to this product after said period has expired. The consumer’s and/or Dealer’s sole remedy
shall be such repair or replacement as is expressly provided above; and under no circumstances
shall American DJ, Inc. be liable for any loss or damage, direct or consequential, arising out of the
use of, or inability to use, this product. This warranty is the only written warranty applicable to American DJ and American Audio Products and supersedes all prior warranties and written descriptions of warranty terms and
conditions heretofore published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
• All American Audio Products = 1-year (365 day) Limited Warranty (except V-Plus Series Amplifiers)
• All American Audio V-Plus Series Amplifiers = 3-year (1095 day) Limited Warranty
• American DJ Lighting and American DJ Branded Products = 1-year (365 day) Limited Warranty
(Such as: Special Effect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble
Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands etc. excluding Laser Products, lamps,
and Star Tec Series)
• American DJ Laser Products and Star Tec Products = 90-Day Limited Warranty
• American DJ L.E.D. Products = 2-year (730 day) Limited Warranty (excluding motors which have a
1-year (365 day Limited Warranty)
©American DJ Supply® - www.americandj.com - Fusion Tri FX Bar - Page 16
Fusion Tri FX Bar
©American
Notes
DJ Supply® - www.americandj.com - Fusion Tri FX Bar - Page 17
Fusion Tri FX Bar
©American
Notes
DJ Supply® - www.americandj.com - Fusion Tri FX Bar - Page 18
Fusion Tri FX Bar
Specifications
Model: Fusion Tri FX Bar
SPECIFICATIONS:
Voltage: 100V~240V 50/60Hz
LEDs:
135 LEDs Total (45 Red, 45 Green,
and 45 Blue
Power Consumption:
32W
Fuse:7 Amp
Power Cord Daisy Chain:19 Fixtures Max.
Weight: 9lbs./ 3.7Kgs.
Dimensions w/ Bracket: 21.25” (L) x 5.75” (W) x 10.5” (H)
538 x 143 x 263mm
DMX Channels:
8
Working Position: Any safe working position
Warranty:
2 Year (730 days)
Auto Sensing Voltage: This fixture contains a automatic volt-
age switch, which will auto sense the voltage when it is plugged
into the power source.
Please Note: Specifications and improvements in the design of
this unit and this manual are subject to change without any prior
written notice.
©American
DJ Supply® - www.americandj.com - Fusion Tri FX Bar -l Page 19
©American DJ Supply
American DJ World Headquarters:
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.americandj.com / E-mail: info@americandj.com
American DJ Europe
Junostraat 2
6468 EW Kerkrade
Netherlands
service@adjgroup.eu / www.americandj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99