ML-7300 Series
User’s Guide
Visit us at:
http://www.samsungprinter.com
P/N. JC68-00608A Rev.1.00
Copyright
The software described in this document is supplied under a license agreement.
The software may be used or copied only in accordance with the terms of this
agreement. It is against the law to copy the software on any medium except as
specifically allowed in the license agreement.
The purchaser may make only one copy of the software for backup purposes.
No part of this manual may be photocopied or transmitted in any form or by any
means, electronic or mechanical including photocopying, recording or information
storage and retrieval systems, for any purpose other than the purchaser’s personal
use, without the expressly written consent of Samsung Electronics Co., Ltd.
Information in this document is subject to change without notice and does not
represent a commitment on the part of Samsung Electronics Co., Ltd. Samsung
Electronics Co., Ltd. or its distributors can in no circumstances be held responsible
for any prejudice, whether direct or indirect, resulting from the use of the software
or the documentation.
August 2000
Trademark Notices
◆ Copyright 2000 SAMSUNG Electronics Co., Ltd. All rights reserved.
◆ All other brand or product names are trademarks or registered trademarks of their
respective companies or organizations.
◆ ML-7300 Series and Samsung logo are trademarks of Samsung Electronics Co., Ltd.
◆ Centronics is a registered trademark of Centronics Data Computer Corporation.
◆ HP, PCL, PCL 6 are registered trademarks of Hewlett-Packard Company.
◆ IBM, IBM PC, XT, AT, PS/2 are registered trademarks of International Business
Machines Corporation.
◆ Apple, AppleTalk, LocalTalk, LaserWriter, TrueType, Macintosh are registered
trademarks of Apple Computer Inc.
◆ Microsoft, MS-windows, MS-DOS are registered trademarks of Microsoft Corporation.
◆ CompuServe is a registered trademark of CompuServe Inc.
◆ TrueDoc
R
is a registered trademark of Bitstream Inc.
◆ Font Navigator is a registered trademark of Bitstream Inc.
TM
◆ PostScript is a registered trademark of Adobe Systems Inc.
Contents
1 Introduction
Safety Precautions - - - - - - - - - - - - - - - - - - - - -1.1
Features and Model Descriptions - - - - - - - - - - - -1.2
Printer Components - - - - - - - - - - - - - - - - - - - -1.3
2 Setting Up your Printer
STEP1:
STEP2:
STEP3:
SETP4:
STEP5:
STEP6:
STEP7:
Unpacking your printer - - - - - - - - - - - -2.1
Installing Toner Cartridge - - - - - - - - - - -2.3
Load Paper - - - - - - - - - - - - - - - - - - - -2.5
Connecting the Parallel Cable - - - - - - - - -2.8
Connecting the AC Power Cord - - - - - - -2.10
Testing the Printer! - - - - - - - - - - - - - -2.11
Setting Up the Printer Driver - - - - - - - -2.12
3 Using Operator Panel
Operator Panel Buttons - - - - - - - - - - - - - - - - - -3.1
Changing Printer Setting - - - - - - - - - - - - - - - - -3.3
Overview of Printer Menu - - - - - - - - - - - - - - - - -3.4
PRINTING MENU - - - - - - - - - - - - - - - - - - - - - -3.5
CONFIG MENU - - - - - - - - - - - - - - - - - - - - - - -3.9
JOB MENU - - - - - - - - - - - - - - - - - - - - - - - - -3.12
TEST MENU - - - - - - - - - - - - - - - - - - - - - - - -3.15
PCL MENU - - - - - - - - - - - - - - - - - - - - - - - - -3.15
I/O MENU - - - - - - - - - - - - - - - - - - - - - - - - - -3.17
PS3 MENU - - - - - - - - - - - - - - - - - - - - - - - - -3.17
NETWORK MENU - - - - - - - - - - - - - - - - - - - - -3.18
4 Print Media
Loading Paper - - - - - - - - - - - Using the Multi-Purpose Tray
- Using the Manual Feed - - - - Letterhead/Prepunched Paper
- Envelopes - - - - - - - - - - - Label - - - - - - - - - - - - - - Transparencies - - - - - - - -
1
-
-
-
-
-
-
-
-
-
-
-
-
-4.1
-4.1
-4.3
-4.4
-4.5
-4.7
-4.8
5 Printing Tasks
Using Features in the Printer Driver - - - - - - - - - - -5.1
Using the Printer Driver - - - - - - - - - - - - - - - - - -5.2
- Paper Tab - - - - - - - - - - - - - - - - - - - - - - - -5.2
- Graphic Tab - - - - - - - - - - - - - - - - - - - - - - -5.4
- Output Tab - - - - - - - - - - - - - - - - - - - - - - -5.6
- Printer Tab - - - - - - - - - - - - - - - - - - - - - - -5.8
- Overlay Tab - - - - - - - - - - - - - - - - - - - - - - -5.9
- Watermark Tab - - - - - - - - - - - - - - - - - - - -5.11
Printing Both Sides of Paper - - - - - - - - - - - - - -5.13
Printing Multiple Pages on One Sheet of Paper - - - -5.16
Printing Booklets - - - - - - - - - - - - - - - - - - - - -5.17
Printing on Different Paper for the First Page - - - -5.18
Fitting Your Document To a Selected Paper Size - - -5.19
Printing Posters - - - - - - - - - - - - - - - - - - - - - -5.20
6 Maintaining your Printer
Toner Cartridge - - - - - - - - - - - - - - - - - - - - - - -6.1
Cleaning the Printer - - - - - - - - - - - - - - - - - - - -6.4
Cleaning LSU - - - - - - - - - - - - - - - - - - - - - - - -6.6
7 Problem Solving
Clearing Paper Jams - - - - - - - - - - - - - - - - - - - -7.1
Error Messages - - - - - - - - - - - - - - - - - - - - - - -7.5
General Printing Problems - - - - - - - - - - - - - - - - -7.8
Poor Print Quality - - - - - - - - - - - - - - - - - - - - - -7.9
PS(PostScript) Problems - - - - - - - - - - - - - - - - -7.10
Network Problems - - - - - - - - - - - - - - - - - - - - -7.10
Macintosh Problems - - - - - - - - - - - - - - - - - - - -7.11
2
A Specifications
Printer Specifications - - - - - - - - - - - - - - - - - - -A.1
Paper Specifications - - - - - - - - - - - - - - - - - - - -A.4
B Macintosh User’s Guide
Setting Up Your Printer - - - - - - - - - - - - - - - - - -B.1
Installing Software
- - - - - - - - - - - - - - - - - - - -B.1
Printing with a Macintosh - - - - - - - - - - - - - - - - -B.5
C Using Windows PostScript Driver
Installing PS Driver - - - - - - - - - - - - - - - - - - - -C.1
D Using the Printer on a Network
About Sharing the Printer on a Network - - - - - - - -D.1
Setting Up a Locally Shared Printer
- - - - - - - - - -D.2
Setting Up a Network-Connected Printer
3
- - - - - - -D.3
E Installing Software from Diskettes
Making Installation Diskettes
- - - - - - - - - - - - - -E.1
Installing Software from Diskettes
- - - - - - - - - - -E.3
F Printer Options
Precautions - - - - - - - - - - - - - - - - - - - - - - - - -F.1
Preparations - - - - - - - - - - - - - - - - - - - - - - - - -F.2
Closing The Printer Cover - - - - - - - - - - - - - - - - -F.3
Understanding the Printer Control Board - - - - - - - -F.4
Printer Memory - - - - - - - - - - - - - - - - - - - - - - -F.5
Network Option Card
- - - - - - - - - - - - - - - - - - -F.8
Installing Serial/LocalTalk or Serial/IrDA option card F.12
Serial/LocalTalk - - - - - - - - - - - - - - - - - - - - - -F.14
Serial/IrDA - - - - - - - - - - - - - - - - - - - - - - - - -F.15
Optional Tray 2 - - - - - - - - - - - - - - - - - - - - - -F.17
G Using Your Printer in Linux
Linux Driver Installation - - - - - - - - - - - - - - - -G.1
INDEX
4
Environmental and Safety Consideration
Laser safety statement
The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR,
chapter 1 Subchapter J for Class I(1) laser products, and elsewhere is certified as a
Class I laser product conforming to the requirements of IEC 825.
Class I laser products are not considered to be hazardous. The laser system and printer
are designed so there is never any human access to laser radiation above a Class I level
during normal operation, user maintenance, or prescribed service condition.
CAUTION
Never operate or service the printer with the protective cover removed
from Laser/Scanner assembly. The reflected beam, although invisible,
can damage your eyes.
Class 1 Laser Statement Label
CLASS 1 LASER PRODUCT
LASER KLASSE 1
LUOKAN 1 LASERLAITE
APPAREIL’ A LASER DE
CLASSE 1
TO IEC 825
5
Environmental and Safety Consideration
Laser caution label
CAUTION
- INVISIBLE LASER RADIATION WHEN THIS COVER IS
OPEN. DO NOT OPEN THIS COVER.
VORSICHT
- UNSICHTBARE LASERSTRAHLUNG, WENN ABDECKUNG
GEÖFFNET. NICHT DEM STRAHL AUSSETZEN.
ATTENTION
- RAYONNEMENT LASER INVISIBLE EN CAS D’OUVERTURE.
DANGEREUSE AU FAISCEAU.
ATTENZIONE
-RADIAZIONE LASER INVISIBILE IN CASO DIAPERTURA.
EVITARE L’ESPOSIZIONE AL FASCIO.
PRECAUCION
-RADIACION LASER IVISIBLE CUANDO SE ABRE.
EVITAR EXPONERSE AL RAYO.
ADVARSEL
- USYNLIG LASERSTRÅLNING VED ÅBNING NÅR SIKKERHEDSBRYDERE
ER UDE AF FUNKTION UNDGÅ UDSAETTELSE FOR STRÅLNING.
ADVARSER
- USYNLIG LASERSTRÅLNING NÅR DEKSEL ÅPNES. STIRR IKKE INN I
STRÅLEN. UNNGÅ EKSPONERING FOR STRÅLEN.
VARNING
- OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPAND OCH
SPÄRREN ÅR URKOPPLAD. BETRAKTA EJ STRÅLEN STRÅLEN AR FARLIG.
VARO
- AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA
NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE ÄLÄ KATSO SÄTEESEEN.
6
Environmental and Safety Consideration
Ozone Safety
During normal operation, the Samsung ML-7300 Series printer
produces ozone. The ozone produced does not present a hazard
to the operator. However, it is advisable that the machine be
operated in a well ventilated area.
If you need additional information about ozone, please contact
your nearest Samsung dealer.
Power Saver
This printer contains advanced energy conservation technology
that reduces power consumption when it is not in active use.
When the printer does not receive data for an extended period of
time, power consumption is automatically lowered.
The energy star emblem does not represent EPA endorsement of
any product or service.
7
Environmental and Safety Consideration
FCC Compliance
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
•
•
•
•
Re-orient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Shielded interface cables and I/O cords must be used for this equipment to
comply with the relevant FCC regulations.
Changes or modifications not expressly approved in writing by Samsung may
void the user’s authority to operate this equipment.
IC COMPLIANCE NOTICE
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations of ICES-003.
Cet appareil numerigue de la Classe B respecte toutes les exigences du
Reglement ICES-003 sur le Materiel brouilleur du Canada.
8
Environmental and Safety Consideration
EC Declaration of Conformity
We,
SAMSUNG ELECTRONICS CO.,LTD
#259, Gong Dan-Dong, Gumi-City, Kyung Buk, Korea
declare sole responsibility that the
ML-7300, ML-7300N Laser Printer
meets the intent of Directive 89/336/EEC for Electromagnetic Compatibility and
Low Voltage Directive 73/23/EEC.
Compliance was demonstrated to the following specifications as listed in the official
journal of the European Communities:
Electro Magnetic Interference (EMI):
EN 55022 Radiated, Class B
EN 55022 Conducted, Class B
EN 61000-3-2 Power Harmonics
EN 61000-3-3 Voltage Fluctuations and Flicker
EN 55024
EN
EN
EN
EN
EN
EN
EN
- Electro Mangnetic Susceptibility (EMS)
61000-4-2 Electrostatic Discharge
61000-4-3 RF Electromagnetic Field
61000-4-4 Fast Transients
61000-4-5 Surges
61000-4-6 RF Common Mode
61000-4-8 Power Frequency Magnetic Field
61000-4-11 Voltage Dips and Interruptions
EN 60950-Safety
Safety information
Safety and Regulatory Listing for this printer.
PRODUCT SAFETY
USA & CANADA
Evaluated by UL according to UL 1950
and CSA C22.2 No. 950 for C-UL
EEC(Europe)
IEC 60950/EN 60950(TUV GS Certification)
CB
IEC 60950
LASER SAFETY
EEC(Europe)
USA
9
HD 194. & EN 60825
21 CFR, Chapter 1, Subchapter J(CDRH Certified)
Environmental and Safety Consideration
Replacing the fitted plug (UK Only)
Important
The mains lead for this machine is fitted with a standard (BS 1363) 13 amp
plug and 13 amp fuse. When you change or examine the fuse, you must re-fit
the correct 13 amp fuse. You then need to replace the fuse cover. If you have
lost the fuse cover, do not use the plug until you get another fuse cover from
the people who sold you the machine.
The 13 amp plug is the most widely used type in the UK. However, some buildings (mainly old ones) do not have normal 13 amp plug sockets. You need to
buy a suitable plug adaptor. Do not remove the moulded plug.
Warning
If you cut off the moulded plug, get rid of it
straight away. You cannot rewire the plug or
you may get an electric shock if you put it into a
socket.
Important warning: You must earth this machine.
The wires in the mains lead use the following colour code:
Green and Yellow
Blue
Brown
: Earth
: Neutral
: Live
If the wires in the mains lead do not match the colours marked in your plug, do
the following:
You must connect the blue wire to the pin which is marked with the letter ‘N’ or
coloured black.
You must connect the brown wire to the pin which is marked with the letter ‘L’
or coloured red.
You must have a 13 amp fuse in the plug, adaptor, or at the distribution board.
10
1
Introduction
Congratulations on the purchase of your
ML-7300 series printer! This chapter provides information
on the following topics:
◆ Safety Precautions
◆ Features and Model Descriptions
◆ Printer Components
Safety Precautions
Before using the printer, please read the instructions in this guide carefully
and put the guide in a safe place close to the printer, so that it is available
when you need it later. Please take the following precautions when using
and maintaining your printer.
●
Unplug the printer before cleaning it. Do Not use any liquid or aerosol
cleaners. Simply use a damp cloth. Refer to the page of this guide for
further details.
●
Do Not place the printer on an unstable surface or close to a radiator or
source of heat.
●
Take care not to block or cover the ventilation holes on the side of the
printer. Do Not insert any object in these holes.
●
Check that the electrical power source to which you wish to connect the
printer complies with the electrical specifications of this printer :
(100 ~ 240V) - Power cord may differ from one country to another.
●
Connect all your computer equipment, including the printer to a power
point with earthing device. Avoid plugging your printer into the same
power point as equipment likely to cause voltage variations, such as a
photocopying machine or an air conditioner.
●
Check regularly that the power cable is in good condition and is not
damaged in any way.
●
If you use an extension cord, check that total intensity of all equipment
connected to it does not exceed the maximum intensity allowed for the
extention cord. Check that the total intensity of the equipment connected
to the same power point does not exceed 15 amps.
●
Unless otherwise indicated in this guide, do not attempt to repair the
printer yourself. Should you detect a fault, return your printer to an
authorized service center or your dealer.
●
Systematically return your printer to an authorised service center or your
local dealer if one of the following situations occurs :
- The power cord or plug is damaged.
- A liquid has been spilled on and/or in the printer.
- The printer has fallen or been dropped or the bodywork is damaged in
any way.
- The printer is not operating correctly or you have noticed a significant
drop in the quality of the printing.
I NTRODUCTION
1.1
Features and Model Descriptions
Your new Printer
Your new Laser Printer is designed for use in an
office environment, providing such advantages as :
●
●
●
●
●
●
Printing on both sides of paper
High-quality, high-speed text and graphics printing
Vast choice of paper types and sizes
Full operating status and error messages on
operator panel display
On-screen feedback of the printing status
Various printer menus
Printer Information
ML-7300
●
The ML-7300 comes equipped with 16MB
RAM and one 500-sheet Tray1 as
standard.
ML-7300N
●
The ML-7300N is equipped with network
card (PortThru) as standard.
Install the network printer driver
(SyncThru) for network printing.
Main Features
This Laser Printer provides the following main features.
Built in Duplex function which allows printing on both
sides of the paper
● Printing speeds of 21PPM(Pages Per Minute) for
Letter-size paper
● High-quality printing at a maximum resolution of 1200 DPI
● Automatic paper feed with a capacity of up to 500 sheets
● Wide range of paper sizes and weights
● Expandable design
- 500-sheet universal paper Tray
- Memory(up to 208 MB)
- Connectors for optional RS-232C/LocalTalk Card and
Network Interface Card
- Connector for optional Infrared Adapter
●
1.2 I NTRODUCTION
Printer Components
Front View
The following illustration shows the front view of your printer and
indicates the various main elements.
Print prevention sensor
Top output bin
Multi-Purpose tray
(It prevents the printer
from printing when 250
sheets of paper are piled
up on the top output bin).
(100-sheet, with extension)
Operator panel
Power switch
Top cover
Tray1
(500-sheet, closed)
Paper level
indicator
LSU cleaner
(When the top
cover is opened)
Rear View
The following illustration shows the rear view of your printer
and indicates the various main elements.
Rear cover
Parallel interface
connector
Power
connector
I NTRODUCTION
1.3
2
Setting Up
Your Printer
This chapter provides step by step information
on setting up your printer.
Topics included in this chapter are:
• STEP 1: Unpacking Your Printer
• STEP 2: Installing Toner Cartridge
• STEP 3: Load Paper
• STEP 4: Connecting the Parallel Cable
• STEP 5: Connecting the AC Power Cord
• STEP 6: Testing the Printer!
• STEP 7: Setting Up the Printer Driver
Unpacking Your Printer
Items Supplied
When you start unpacking the box of your printer, you will find the following
items in addition to your printer.
Toner cartridge
Power cord*
CD-ROM Disk
This manual
Notes: • If you find that any of the above items are missing or damaged,
contact your local dealer.
• A printer cable is not included in the package items.
• Cable specifications
- The parallel cable should be compatible with the centronics®
parallel interface and IEEE standard 1284.
• * Power cord may differ from one country to another.
S ETTING U P Y OUR P RINTER
2.1
Unpacking Your Printer
Preparation
During the storage and transport of your printer, adhesive tape is used to block
some of the elements that may move or open unexpectedly and consequently
be damaged.
1 Before connecting up your printer
and starting to use it, you must
remove all the adhesive tapes,
as illustrated in the figure below.
2 Slide the tray out of the printer.
Remove the packaging material
from the tray.
2.2 S ETTING U P Y OUR P RINTER
Installing Toner Cartridge
To install a toner cartridge in your printer proceed as follows.
1 Remove the toner cartridge from
its packaging.
Notes: • Do not remove the cartridge
from its packaging until you
are ready to use it.
• Do not expose the cartridge
to light, it could damage the
cartridge permanently.
2 Open the top cover of the printer
by pressing the button on the
right side of the printer.
S ETTING U P Y OUR P RINTER
2.3
Installing Toner Cartridge
3 Rotate the cartridge and gently
shake it from side to side to
distribute the toner evenly inside
the cartridge.
4 Position the cartridge as shown
with the arrow pointing into the
printer. Slide the cartridge into the
printer as far as it will go.
5 Close the top cover.
Notes: If toner gets on your clothing, wipe it off with a dry cloth and wash clothing
in cold water. When printing text at 5% coverage, a toner cartridge lasts an
average of 10,000pages in simplex mode.
2.4 S ETTING U P Y OUR P RINTER
Load Paper
To load paper in the tray, proceed as follows.
1 Pull the Tray1 completely out of
the printer.
2 Squeeze the back of the rear
paper guide and slide it to the
desired paper size until it clicks
into place.
The paper sizes are indicated on
the bottom of the tray1.
Rear paper
guide
S ETTING U P Y OUR P RINTER
2.5
Load Paper
3 Lift the rear right guide and slide
it to match the width of the paper.
The paper sizes are indicated on
the bottom of the tray.
4 Squeeze the width guide and slide
it to the far right side of the tray.
Width guide
Rear right guide
Notes: If the tray is not properly adjusted, the printer might display an error
message or paper might jam.
5 Place the paper against the rear
paper guide as shown.
Paper Limit Line
Printing side(down)
Notes:
•
•
•
Do not fold or crease the paper.
Place the paper with the recommended print side face down.
Don’t exceed the paper limit line indicated on the tray.
2.6 S ETTING U P Y OUR P RINTER
Load Paper
6 Squeeze the width guide and slide
it to the left until it lightly rests
against the edge of the paper.
7 Make sure the paper is under
the tab on the tray.
8 Gently slide the tray back into the
printer. The printer automatically
senses the size of paper loaded
if the tray1 is adjusted correctly.
Notes: If jam 0 often occurs when 24lb
letter, legal or folio size paper is used,
push down the lever on the left side of the
tray as shown in the figure to ensure
proper paper feeding.
S ETTING U P Y OUR P RINTER
2.7
Connecting the Parallel Cable
To print from computer software, you need to connect your printer to your
computer with a parallel interface cable.
Cable Specifications (Not provided)
The parallel cable should be compatible with the Centronics R parallel interface
and IEEE standard 1284. If you purchase a parallel cable, ensure that it :
• Is compatible with Centronics interface.
• Supports bi-directional communications(IEEE standard 1284).
• Is shielded.
• Has the appropriate connector :
- 25 pin D-Sub connector on the computer side.
- Amphenol 36 connector on the printer side.
Connecting the Parallel Cable
To connect the printer to your computer use a parallel cable and
proceed as follows.
1 Check that both the printer and the computer to which it is to be connected
are powered off and disconnected from the power point.
2 Plug the appropriate end of the
parallel cable into the connector on
the rear of the printer.
2.8 S ETTING U P Y OUR P RINTER
Connecting the Parallel Cable
3 Push the clip at each end of the
connector down into the notches
on the plug as shown.
4 Plug the other end of the cable
into the appropriate parallel
connector on your computer and
tighten the screws.
MIDI/GAME
LINE
OUT
LINE
IN
PHONE LINE
S ETTING U P Y OUR P RINTER
2.9
Connecting the AC Power Cord
To connect the printer to a power point, proceed as follows.
1 Plug the appropriate end of the
supplied power cable to the
connector on the rear of the
printer.
2 Plug the other end into a suitable
power point.
• Power cord may differ from
one country to another.
3 Power the printer on by pressing
the power on/off button.
Result: You will hear some movement inside the printer.
The printer enters the Ready state.
2.10 S ETTING U P Y OUR P RINTER
Testing the Printer!
Print a configuration page to make sure the printer is operating correctly.
1 Make sure that the READY status message
appears on the display.
2 Press On Line.
Result: The OFFLINE message appears on the display
and the printer is off-line.
3 Press Menu > or < Menu to enter the menus.
4 Press Menu > or < Menu one or more times until
the TEST MENU message is displayed.
5 Press Item> or <Item one or more times until
the SELFTEST message is displayed.
6 Press Enter to print.
Notes: • The message ‘PRINTING PCL6’ appears and remains
on the display until the page prints.
• The printer returns to the Ready state after printing.
S ETTING U P Y OUR P RINTER
2.11
Setting Up the Printer Driver
The printer drivers provided on the CD must be installed to take full
advantage of the printer’s features.
Printer drivers access the printer features and allow the computer to
communicate with the printer.
If you install the printer driver using the CD, PCL 6 is installed.
The CD includes the following printer drivers.
• PCL 6
- You can use the PCL 6 driver in Windows 95, Windows 98, Windows NT 4.0
and Windows 2000.
The PCL6 driver supports Watermark, Overlay, N-Up and Poster printing.
• Postscript.
• Font Navigator.
• Linux Driver.
Notes: • You cannot use PostScript in Windows 3.1.
• PCL 6 is the combination of the PCL 5e driver and the new PCLXL printer
language.
2.12 S ETTING U P Y OUR P RINTER
Setting Up the Printer Driver
Installing the Driver
Hardware Requirements
To install and run the PCL printer driver, you must have the following minimum
hardware configuration.
• Windows 95 or Windows 98
- PC-compatible 486 computer or better.
- 32MB RAM
- 200MB available hard-disk space.
• Windows NT 4.0 or Windows 2000
- PC-compatible pentium 133MHz computer or better.
- 64MB RAM
- 650MB available hard-disk space.
• CD-ROM Drive.
Software Requirements
To install and run the printer driver, you must be running one of the
following platforms.
• Windows 95, Windows 98, Windows NT 4.0, Windows 2000.
• Macintosh System 7.5 or later.
Install Procedure
To install the printer driver on your hard disk, make backup copies of the print
driver CD. Keep the original CD in a safe place and use the copies.
Notes: I do not have a CD-ROM driver
If you have access to another computer with a CD-ROM drive, you can use
the Make diskette utility in Windows to create the disks you need for the
installation. Go to Appendix E, “Installing Software form Diskettes”
S ETTING U P Y OUR P RINTER
2.13
Setting Up the Printer Driver
Installing the Printer Software from the CD-ROM
S
00
SUNG ML-73
AM
1 Place the CD-ROM in the CD-ROM drive. Install will start
automatically.
If the CD-ROM drive does not automatically run:
Select Run from the Start menu, and type x:\cdsetup.exe
in the Open box (where x is the drive letter for the CD-ROM
drive), and then click OK.
Notes: If the New
Hardware Found box
appears during the
installation procedure,
click the x in the upper
right corner of the box,
or click Cancel.
2 When the opening screen appears, select the appropriate
language.
3 Click Install the Samsung Software-I on your PC.
4 Follow the instructions on the screen to complete
the installation.
2.14 S ETTING U P Y OUR P RINTER
Setting Up the Printer Driver
Notes: To Install Shared Win 95/98 Printer Driver from NT Server to Client PC
1 Select Sharing in Properties of the printer driver.
2 Select Windows 95 in Alternate Drivers.
3 Type D:\7300\XX\pcl\pcl6\win9x
(Where “D” is your CD-ROM drive letter and XX is the language code*,
i.e. eng for English).
Install
the network printer in the client PC.
4
* Refer to “language code” (page 2.17) for language codes.
Uninstalling the Printer Driver
An uninstall utility is supplied with the printer driver to enable you to
remove the driver and all associated files from your hard disk, if so required.
To uninstall the driver, proceed as follows.
Select Start ➔ Programs ➔ Samsung ML-7300 ➔ Samsung ML-7300
Driver uninstall from the windows task bar.
●
The PCL 6 driver is removed from your hard disk.
S ETTING U P Y OUR P RINTER
2.15
Setting Up the Printer Driver
Installing the Font Navigator (FontNav)
Font Navigator is a font manager for Windows 95/98, Windows NT(4.0)
and Windows 2000. It gives a quick and easy way to find fonts, install those
fonts, and view and print font samples.
S
00
SUNG ML-73
AM
1 Place the CD-ROM in the CD-ROM drive. Install will start
automatically.
If the CD-ROM drive does not automatically run:
Select Run from the Start menu, and type x:\cdsetup.exe
in the Open box (where x is the drive letter for the CD-ROM
drive), and then click OK.
Notes: If the New
Hardware Found box
appears during the
installation procedure,
click the x in the upper
right corner of the box,
or click Cancel.
2 When the opening screen appears, select the appropriate
language.
3 Click Install the Bonus Software on your PC.
4 Follow the instructions on the screen to complete
the installation.
2.16 S ETTING U P Y OUR P RINTER
Setting Up the Printer Driver
Language Codes
Codes
Language
Eng
English
Deu
German
Frn
French
Esn
Spanish
Ita
Italian
Kor
Korean
S ETTING U P Y OUR P RINTER
2.17
3 Using
Operator
Operator
Panel
This chapter describes how to use the printer’s operator
panel. It provides information on the following topics:
◆ Operator Panel Buttons
◆ Changing Printer Setting
◆ Overview of Printer Menu
◆ PRINTING MENU
◆ CONFIG MENU
◆ JOB MENU
◆ TEST MENU
◆ PCL MENU
◆ I/O MENU
◆ PS3 MENU
◆ NETWORK MENU
Operator Panel Buttons
LCD panel
The operator panel, on the front right side
of your printer, has a 2-line LCD(Liquid
Crystal Display) and five buttons.
Operator Panel
Display
Light Color
Light State
The Printer IS...
Green
On
Online
Off
Offline
Blinking
Processing information.
On
In Non-recoverable error state
• Solve the problems for the
error message, by going
through check lists and tests.
Blinking
In recoverable error state.
Orange
U SING O PERATOR PANEL
3.1
Operator Panel Buttons
Using Panel Buttons
Use the five operator panel buttons to open a menu, scroll through a list of values,
change printer settings, and respond to printer messages.
The following table describes the functions of each button.
Button
Function
On Line/Continue • Places the printer either online or offline.
• Allows the printer, to continue printing when the
printer is in recoverable error state.
Enter/Cancel
• Cancels the print job that the printer is processing
when the printer is online.
• Saves the selected value for that item when the
printer is offline.
Menu
• Cycles through the operator panel menus.
Item
• Cycles through the selected menu’s items.
Value
• Cycles through the selected menu item’s values.
Operator Panel Menus
A number of menus are available to make it easy for you to change printer settings.
Some menus are displayed only if a specific option is installed in the printer.
When you select a new setting from the operator panel, the asterisk(❊) moves
next to the selected setting to identify it as the current user default setting.
Notes: Changes made from a software application override the user default
settings made from the printer operator panel.
3.2 U SING O PERATOR PANEL
Changing Printer Setting
To change an operator panel setting, proceed as follows.
1 Make sure the ‘READY’ message appears on the display.
2 Press On Line.
Result: The ‘OFFLINE’ message appears on the display and the
printer is off-line.
3 Press Menu until the menu you need appears on the display.
4 Press Item until the menu item you need appears on the display.
5 Press Value until the setting you need appears on the display.
6 Press Enter to save the selection.
Result : An asterisk(❊) appears beside the current user default
setting for that menu item.
A value can be :
• A phrase or word that describes a setting.
• A numerical value that you can increase or decrease.
• An On or Off setting.
U SING O PERATOR PANEL
3.3
Overview of Printer Menu
PRINTING
MENU
CONFIG
MENU
JOB
MENU
TEST
MENU
PCL
MENU
PAPER
EMUL
FONTLIST
SWITCH
DEMOPAGE
TYPEFACE
COPIES
LOCKTRAY
ORIENT
PWR SAVE
TRAY
AUTOCONT
T-MARGIN
ECONO
L-MARGIN
JAM RECV
DUPLEX
TONERLOW
SRT MODE
TIMEOUT
DENSITY
PAP.TYPE
MENU CLR
SMET
DUP.TOP
DUP.LEFT
S-BIND
L-BIND
FUSER CLEAN
SELFTEST
MP SIZE
AUTO CR
WIDE A4
SYMBOL
LINES
PITCH
PT.SIZE
COURIER
QUALITY
Some menus are displayed only if a required option is installed.
They are as follows.
NETWORK MENU
I/O MENU
PS 3 MENU
If the Network card(PortThru)
is installed in your printer
If the serial/LocalTalk option
card is installed in your printer
BAUDRATE
RESET NIC
NETWARE
FONTLIST
ROBU.XON
CFG NET
CFG NWAR
PS.ERROR
TCP/IP
AUTO
CFG TCP
EN_8023
DHCP
EN_II
CFG ADRS
EN_8022
IP BYTE
1, 2, 3, 4
EN_SNAP
SM BYTE
1, 2, 3, 4
3.4 U SING O PERATOR PANEL
UPDATE
BOOT SVR
GW BYTE
1, 2, 3, 4
SV-IP B1
BOOTP
SV-IP B3
RARP
SV-IP B4
LPD
FACTORY DEFAULT
APL TALK
PRINT NET CFG
SV-IP B2
PRINTING MENU
Use the PRINTING MENU to define all settings relating to printer input and
output, as well as the specific print materials you are using with your printer.
Item
PAPER
Values and Functions
If the TRAY menu is AUTO, MP, MANUAL
A4(country specific), LEGAL, Letter(country specific), EXE,
JIS B5, ISO B5, COM-10, MONARCH, DL, C5, POST A6, C6,
FOLIO, A5, STS, A6
If the TRAY menu is 1ST
A4(country specific), LEGAL, Letter(country specific), EXE,
JIS B5, ISO B5, FOLIO
If the TRAY menu is OPT
A4(country specific), LEGAL, Letter(country specific), EXE,
JIS B5, ISO B5, COM-10, MONARCH, DL, C5, FOLIO
If the DUPLEX menu is not OFF(SHORT or LONG)
A4(country specific), LEGAL, Letter(country specific), FOLIO
MP SIZE
If the DUPLEX menu is OFF
A4(country specific), LEGAL, Letter(country specific), EXE,
JIS B5,ISO B5, COM-10, MONARCH, DL, C5,
POST A6, C6, FOLIO, A5, STS, A6
If the DUPLEX menu is not OFF
(SHORT or LONG)
A4(country specific), LEGAL, Letter(country specific), FOLIO
Notes: The PAPER SIZE setting identifies the default formatting size for each tray.
It is important to select the correct paper size from the menu when using
trays.
U SING O PERATOR PANEL
3.5
PRINTING MENU
Item
COPIES
Values and Functions
1 to 999 (1; Factory Default)
The COPIES setting determines the number of copies
printed for each page. The printer does not automatically
collate the copies. For example, if you send three pages to
print and set Copies to 2, the printer prints page1, page 1,
page 2, page 2, page 3, page 3.
ORIENT
P : Portrait (Factory Default)
L : Landscape
The ORIENT setting determines how the
printing is oriented on the page.
P(Portrait) means the printing is parallel to the
short edge of the paper.
L(Landscape) means the printing is parallel to
the long edge of the paper.
Portrait
3.6 U SING O PERATOR PANEL
Landscape
PRINTING MENU
Item
TRAY
Values and Functions
AUTO(Factory Default)
1ST
MP
OPT(If the optional cassette is installed)
MANUAL
The TRAY setting identifies the default paper tray.
1ST means that the printer feeds print material from Tray
unless it is empty or opened.
MP means that the printer feeds print material
from Multi-Purpose tray unless it is empty or closed.
Use the MANUAL selection when manually feeding
envelopes or other print material through the
Multi-Purpose tray.
OPT is available only if the optional tray 2 is installed.
See ‘Optional Tray 2’ on page F.17.
Auto means that the printer feeds print material from the other
tray when one tray is empty. If you are using the same size
and type of print material in all the trays, the trays are
automatically linked.
T-MARGIN
0.0” ~ 9.9”
The T-MARGIN menu item lets you select the top margin of
the print materials.
U SING O PERATOR PANEL
3.7
PRINTING MENU
Item
L-MARGIN
Values and Functions
0.0”~ 9.9”
The L-MARGIN menu item lets you select the
left margin of the print materials.
DUPLEX
OFF (Factory Default)
LONG
SHORT
The printer can automatically print on both sides of paper.
Use the OFF selection when printing on one side of a
sheet of paper. For more information, see page 5.13.
Long
Short
AUTO CR
LF(Factory Default)
LF + CR
The AUTO CR setting determines if the printer
automatically performs carriage return after a line feed
control command.
WIDE A4
OFF (default)
ON
The WIDE A4 setting determines if the printer can print
80 columns in A4 size.
QUALITY
300
600 (Factory Default)
1200
QUALITY setting determines the print resolution while
printing the page.
3.8 U SING O PERATOR PANEL
CONFIG MENU
Use the CONFIG MENU to configure a variety of printer features.
Item
EMUL
Values and Functions
AUTO (Factory Default)
PCL
PS3
HEXDUMP
You can select the emulation for printing a document.
PWR SAVE
120
15
30 (Factory Default)
45
60
The PWR SAVE menu item lets you reduce power
usage when the printer is idle. The PWR SAVE setting
determines the length of time (in minutes) the printer
waits after a job is printed before it goes to a reduced
power state.
AUTOCONT
ON (Factory Default)
OFF
The AUTOCONT setting determines whether the printer
continues printing after it detects paper mismatch.
If an error occurs and AUTOCONT is set to OFF,
the printer stops and waits for operator intervention.
If the Continue button on the operator panel is pressed,
the printer continues printing regardless of paper mismatch. When AUTOCONT is set to ON, the printer automatically resumes processing.
U SING O PERATOR PANEL
3.9
CONFIG MENU
Item
ECONO
Values and Functions
OFF (Factory Default)
ON
The ECONO setting helps conserve the toner cartridge
by controlling how much toner the printer uses for a print
job.
Select OFF if toner conservation is not a concern.
But this setting may affect the print quality of your job.
JAM RECV
OFF (Factory Default)
ON
When JAM RECV is set to OFF, the printer does not
reprint a page that has been jammed.
When JAM RECV is set to ON, the printer keeps a
printed page until the printer signals that the page has
successfully exited the printer. The printer reprints the
jammed page.
TONERLOW
CONTINU (Factory Default)
STOP
This setting determines whether the printer can continue
printing after the printer detects that the toner is low.
If the toner is low and TONERLOW is set to ‘Stop’,
press the Continue button to print. In that case, replace the
toner cartridge or set the TONERLOW menu item to
CONTINU.
3.10 U SING O PERATOR PANEL
CONFIG MENU
Item
Values and Functions
SWITCH
ON (Factory Default)
(If the optional
OFF
tray 2 is installed)
The ON setting makes the printer supply the paper from
another Tray when a tray is empty.
In case of the OFF setting, an error message is
displayed.
LOCKTRAY
NONE (Factory Default)
(If the optional
1ST
tray 2 is installed
OPT
and the SWITCH
menu item is set to
ON)
MP
The tray set to LOCKTRAY doesn’t change.
For example, if LOCKTRAY is set to MP, the tray is not
switched to Multi-Purpose tray.
U SING O PERATOR PANEL
3.11
JOB MENU
Use the JOB MENU to define all settings relating to print quality,
as well as Menu clear.
Item
Values and Functions
SRT MODE
ENHANCE (Factory Default)
(Samsung
Resolution
Enhancement
Technology)
NORMAL
GRAY
Use the printer’s SRT(Samsung Resolution enhancement
Technology) setting to produce print with smooth angles,
curves, and edges.
ENHANCE : Better Text Image
GRAY : Better Photo Image
TIMEOUT
0~300
15(Factory Default)
The TIMEOUT Setting determines the amount of time
(in seconds) the printer waits before printing the last page
of a print job that does not end with a command to print
the page. When a print timeout occurs, the printer prints
the data in the print buffer.
0 : No timeout.
DENSITY
LIGHT
MEDIUM (Factory Default)
DARK
Lighten or darken the print on the page by changing the
DENSITY setting.
The MEDIUM setting usually produces the best results.
3.12 U SING O PERATOR PANEL
JOB MENU
Item
PAP.TYPE
Values and Functions
NORMAL (Factory Default)
THICK
WET
TRANSP.
The PAP.TYPE setting lets you specify the type of print
material installed in each tray.
Select NORMAL if the printer material is plain paper.
Select THICK if the printer material is thick paper, high
cotton paper or envelopes.
Select WET if printer material is thin paper(60g)
and the air is humid.
Select TRANSP. if printer material is transparencies.
This value can only be selected if MP or manual has been
selected from the Tray menu.
MENU CLR
When you select MENU CLR, the printer resets to the
factory default setting for each menu item.
SMET
ON (Factory Default)
(Samsung Memory
Enhancement
Technology)
OFF
This setting makes the printer process more data by
optimizing the memory.
If the value is set to ON, the complex data can be
processed.
U SING O PERATOR PANEL
3.13
JOB MENU
Item
DUP.TOP
Values and Functions
5.0 (Factory Default)
0~9.9mm (In increments of 0.1)
This item lets you select the top margin of the print
materials when the Duplex menu item is set to Long.
DUP.LEFT
5.0 (Factory Default)
0~9.9mm (In increments of 0.1)
This item lets you select the left margin of the print
materials when the Duplex menu item is set to Long.
S-BIND
0 (Factory Default)
0~22mm (In increments of 1)
This item lets you select the left margin for the binding
when short edge duplexing.
L-BIND
0 (Factory Default)
0~22mm (In increments of 1)
This item lets you select the left margin for the binding
when long edge duplexing.
FUSER CLEAN
Select ‘FUSER CLEAN’ if you notice random dirty spots on
the back side of the paper.
It cleans fuser contamination.
3.14 U SING O PERATOR PANEL
TEST MENU
Use the TEST MENU to print a variety of listings relating to available
printer resources, printer settings and print jobs.
Item
SELFTEST
Values and Functions
Select SELFTEST to print a configuration page. This menu
item lets you make sure the printer is operating correctly.
For more information, see page 2.11.
DEMOPAGE
Select DEMOPAGE to print the standard demonstration
page.
PCL MENU
Use the PCL MENU to change printer settings that only affect jobs
printed using the PCL emulation printer language.
Item
Values and Functions
FONTLIST
You can print a font sample list showing all
the fonts available for PCL emulation.
TYPEFACE
PCL 1 ~ PCL 54
PCL 1 (Factory Default)
SYMBOL
ROMAN 8
DESKTOP
.
.
PC8 (Factory Default)
List of symbol set name
A SYMBOL set is a set of alphabetic and numeric
characters, punctuation, and specific symbols used when
printing with a selected font.
In PCL emulation, a symbol set also defines which
character will be printed for each key on the keyboard (or
more specifically, for each code point).
U SING O PERATOR PANEL
3.15
PCL MENU
Item
LINES
Values and Functions
5 ~ 128
60 (Factory Default : USA, Canada)
64 (Factory Default : Others Country)
Use the LINES menu item to change the number of lines
that print on each page.
The setting can range from 5 to 128 lines per page.
The printer sets the amount of space between each line
based on the Lines, Paper size, and Orientation settings.
PITCH
0.44~99.99
10.00 (Factory Default)
If you chose a scalable monospaced font, you can select
the font pitch.
PITCH refers to the number of fixed - space characters
in a horizontal inch of type.
You can select from 0.44 to 99.99 characters per inch
in increments of 0.01 cpi.
PT.SIZE
You can select the character size for the font.
PITCH or PT.SIZE appears according to the value of
TYPEFACE.
COURIER
REGULAR (Factory Default)
DARK
3.16 U SING O PERATOR PANEL
I/O MENU
This menu is only available if the Serial/LocalTalk option card is installed in
your printer.
Item
Values and Functions
BAUDRATE
This setting lets you select the rate at which data is being
sent to or from your computer.
Setting the COM Port and printer setting at anything
higher that 19200 bps will create unexpected errors
in DOS mode.
300~115200
9600(Factory Default)
ROBU.XON
ON(Factory Default)
OFF
PS3 MENU
Item
FONT LIST
Values and Functions
Prints the font list showing all the fonts available for
PostScript.
PS.ERROR
ON
OFF (Factory Default)
Determines what action the printer should take when an
error occurs in PS interpreter. When set to OFF, the printer
does not print error information when an error occurs in PS
interpreter. When set to ON, the printer prints error information when an error occurs in PS interpreter.
U SING O PERATOR PANEL
3.17
NETWORK MENU
This menu is only available if the Network option card is installed in your
printer.
Menu
Item
Value
Enter/Cancel
On Line
On Line
Pressing Menu
Pressing
cycles forward or
On Line/Continue
backward
OFFLINE
3.18 U SING O PERATOR PANEL
NETWORK
MENU
Pressing Item cycles Pressing Value cycles
forward or backward forward or backward
RESET NIC
Pressing
Enter/Cancel
Pressing
On Line/Continue
The PortThru card is reset
CFG NET
NO
Select YES or NO
TCP/IP
ON
Select ON or OFF for enabling
CFG TCP
NO
Select YES or NO
LPD
ON
Select ON or OFF for LPD printing
APL TALK
ON
Select ON or OFF for enabling
NETWARE
ON
Select ON or OFF for IPX/SPX
CFG NWAR
NO
Select YES or NO
UPDATE
NO
Select YES or NO or for
upgrading
BOOT SVR
UNIX
Select Unix or Windows
FACTORY
DEFAULT
Select for Factory Default
settings
PRINT
NET CFG
Select for test printing
NETWORK MENU
Item
Values and Functions
RESET NIC
The PortThru card is reset.
CFG NET
YES
NO
This menu item lets you configure network settings.
TCP/IP
ON
OFF
This menu item lets you enable TCP/IP.
CFG TCP
YES
NO
This menu item lets you configure TCP/IP.
LPD
ON
OFF
This menu item lets you print using LPD.
DHCP
CFG ADRS
BOOTP
RARP
YES
NO
APL TALK
ON
OFF
You can configure the print server for TCP/IP
configuration parameters, DHCP, CFG ADRS, BOOTP, and
RARP. When you enable TCP/IP protocol, you have to select
one of the IP Address assignment methods, DHCP, CFG
ADRS, BOOTP, RARP. In case of DHCP, RARP, BOOTP, you
need to configure the server. In case of CFG ADRS, you
have to enter the IP address, Subnet mask, Default
Gateway manually.
When you set APL TALK to OFF, this PortThru can not be
detected by Macintosh systems.
NETWARE
ON
OFF
You can configure the printer server for IPX/SPX
configuration parameters, and FRAME. When you set it to
ON, you may select the Frame Type.
U SING O PERATOR PANEL
3.19
NETWORK MENU
Item
CFG NWAR
Values and Functions
YES
NO
This menu item lets you configure IPX/SPX configuration
parameters.
AUTO
EN-8023
EN-II
EN-8022
EN-SNAP
ON
OFF
UPDATE
YES
NO
These items are the frame type for IPX/SPX protocol.
You can select one of these. If you don’t set any value,
Auto(default value) which switches the frame types
automatically is used.
You need to set the server that provides the upgrade file.
You can set it to UNIX or WINDOWS. After setting the server
for update, you should reset the printer. The upgrade process
will be completed.
BOOT SVR
UNIX
WINDOWS
If you want to upgarde in UNIX System, please select UNIX.
You have to store the file to be upgraded in temporary
directory of UNIX system and configure MAC address,
IP address, the file name and the file path in bootptab file. If
you want to upgrade in WINDOWS System, please select
WINDOWS. You have to enter the IP address of Windows’s PC
that has the upgrade file.
FACTORY
DEFAULT
You can reconfigure the PortThru card to the factory default
value for each menu item. After selecting this menu, make
sure that you reset printer.
PRINT NET CFG
Select this menu item to print configuration pages.
3.20 U SING O PERATOR PANEL
NETWORK MENU
Resetting PortThru
To reset PortThru
1
2
3
4
Press On Line/Continue. OFFLINE appears on the display.
Press Menu until NETWORK MENU appears on the display.
Press Item until RESET NIC appears on the display.
Press Enter and READY appears on the display.
Configuring Network setting for PortThru
To configure network settings for PortThru.
1
2
3
4
5
6
Press On Line/Continue. OFFLINE appears on the display.
Press Menu until NETWORK MENU appears on the display.
Press Item until CFG NET appears on the display.
Press Value until YES appears on the display.
Press Enter and you can configure the following network settings now.
Skip this step if you don’t want to configure TCP/IP. Press Item until
TCP/IP appears on the display.
a Press Value until ON appears on the display.
b Press Enter and PortThru can use TCP/IP
for communicating.
c Press Item until CFG TCP appears on the display.
d Press Value until YES appears on the display.
e Press Enter and you can select the IP address assign
ment method.
f Press Item until the IP address assignment method
you want appears on the display.
g Select the YES by pressing the Value button.
h Press Enter.
i Skip this step if you don’t select CFG ADRS as the IP address
assignment method. Enter the IP address,
Subnet mask, Default gateway by using Item,
Value and Enter buttons.
U SING O PERATOR PANEL
3.21
NETWORK MENU
7
Skip this step if you don’t want to use LPD. LPD appears only if
TCP/IP is ON. Press Item until TCP/IP appears on the display.
a
b
c
d
e
8
Press Value until ON appears on the display.
Press Enter.
Press Item until LPD appears on the display.
Select the ON by pressing the Value button.
Press Enter and PortThru can print using LPD.
Skip this step if you don’t want to use AppleTalk protocol.
Press Item until APL TALK appears on the display.
a Take the ON by pressing the Value button.
b Press Enter and PortThru can communicate with AppleTalk
protocol.
9
Skip this step if you don’t want to use IPX/SPX protocol.
Press Item until NETWARE appears on the display.
a Press Value until ON appears on the display.
b Press Enter.
c Skip this step if you do not want to configure IPX/SPX. Press
Item until CFG NWAR appears on the display. Select the YES
by pressing the Value button, then Press Enter.
d Press Item until the frame type you want to use appears on
the display.
e Select the ON by pressing the Value button.
f Press Enter.
3.22 U SING O PERATOR PANEL
NETWORK MENU
Upgrading Firmware In Front Panel
To upgrade the firmware of your PortThru. This section is
explaination of upgrading the Firmware in abnormal case.
Generally, please use SyncThru for upgrading Firmware.
1 Press On Line/Continue. OFFLINE appears on the
display.
2 Press Menu until NETWORK MENU appears on the
display.
3 Press Item until UPDATE appears on the display.
4 Select YES by pressing the Value button.
5 Press Enter.
6 If Unix is the server that provides the upgrade file, go to
step 7. Otherwise go to step 8.
7 In case of Unix server:
a Press Item until BOOT SVR appears on the display.
b Press Value until UNIX appears on the display.
c Go to step 9.
8 In case of Windows server: This step should be taken after
executing the section Upgrading Firmware In Abnormal
Cases (see page 3.26).
a Press Item until BOOT SVR appears on the display.
b Press Value until WINDOWS appears on the display.
c Enter the IP address of the server to provide upgrade
file by using Item, Value and Enter button.
9 Please refer Upgrading the Firmware in UNIX Environment
or Upgrading the Firmware in Windows Environment. And
then Reset print and the firmware will be upgraded.
U SING O PERATOR PANEL
3.23
NETWORK MENU
Restoring Factory Defaults
To restore factory default settings to the printer.
1
Press On Line/Continue. OFFLINE appears on the display.
2
Press Menu until NETWORK MENU appears on the display.
3
Press Item until FACTORY DEFAULT appears on the display.
4
Press Enter.
5
Reset printer and all settings will be reset to factory defaults.
Printing Test Pages
You can use the Front Panel to print out important information
pages describing PortThru settings.
3.24 U SING O PERATOR PANEL
1
Press On Line/Continue. OFFLINE appears on the display.
2
Press Menu until NETWORK MENU appears on the display.
3
Press Item until PRINT NET CFG appears on the display.
4
Press Enter and the test pages will be printed out.
NETWORK MENU
Upgrading the Firmware in a Unix Environment
Setting Unix as BOOTP server
1
There must be a BOOTP server present in the network
environment in which the network printer is present.
2
On the BOOTP server the /etc/bootptab file must be created and an
entry for the boot parameters must be made in the file as follows:
(Please check with your system manual).
npc:\
:pc:\
:ht=ether:\
:ha=0000F0A12345:\
:sm=255.255.255.0:\
:gw=200.160.251.1:\
:lg=200.160.251.51:\
:sa=200.160.251.52:\
:hn:
:ip=200.460.251.18:\
:bf=”/test/Firmwareup”.\
:vm=rfc1048:
:ht=hardware type, ha=hardware add, image:download file name
Upgrading the Firmware
1
Set UPDATE to YES in the Network menu on the printer front panel.
2
Set BOOT SVR to UNIX.
3
Reset the printer.
4
It may take 3 minutes to reboot the printer.
Rebooting time depends on network traffic.
Notes: • Firmware upgrading requires Tftp protocol.
Check whether Tftp daemon is installed in advance.
• Setting IP Address Assignment Method to DHCP is
recommended in order to execute Firmware upgrading.
U SING O PERATOR PANEL
3.25
NETWORK MENU
Upgrading the Firmware in Abnormal Cases
Any error in the process of upgrading may result in disabling
PortThru. In this case, perform the following steps.
In SyncThru
1
Select the Upgrade Firmware menu item under the
Maintenance menu in SyncThru.
2
You can see the Choose the Upgrade Firmware File dialog box.
3
Check “Wait Printer Request” and “Set as Default Download”.
4
Select the Firmware file Name you downloaded and its path,
and then click Start.
5
You will see the message ”Please set the values through the
FRONT Panel to initiate FLASH Upgrade”. Click OK.
After this procedure, move to printer which you want to
update and do as following procedure.
In Front Panel of the printer
6
Press On Line. OFFLINE appears on the display.
7
Press Menu until NETWORK MENU appears on the display.
8
Press Item until UPDATE appears on the display.
9
Select YES by pressing the Value button.
10
Press Enter/Cancel.
11
Press Item until BOOT SVR appears on the display.
12
Press Value until WINDOWS appears on the display.
13
Press Enter/Cancel.
3.26 U SING O PERATOR PANEL
NETWORK MENU
14
Set the IP address of the WINDOWS pc running SyncThru
in step1. For example, if the IP address is 155.213.211.12,
follow these steps:
a Press Item until SV-IP B1 appears on the display.
b Press Value until 155 appears on the display.
c Press Enter/Cancel.
d Press Item until SV-IP B2 appears on the display.
e Press Value until 213 appears on the display.
f Press Enter/Cancel.
g Press Item until SV-IP B3 appears on the display.
h Press Value until 211 appears on the display.
i Press Enter/Cancel.
j Press Item until SV-IP B4 appears on the display.
k Press Value until 12 appears on the display.
l Press Enter/Cancel.
15
Reset printer and the firmware will be upgraded.
Notes: After the ”Completed. Network Card will start about 30secs
later” message is displayed on SyncThru, click OK.
It may take a few seconds to write the new file to Firmware.
Normally 30 seconds is sufficient.
U SING O PERATOR PANEL
3.27
4 Print Media
This chapter will help you understand what kind of paper
you can use with the ML-7300 series printer and how to
properly load paper in the different paper trays for the best
print quality.
Topics included in this chapter are:
◆ Loading Paper
- Using the Multi-Purpose Tray
- Using the Manual Feed.
- Letterhead/Prepunched Paper
- Envelopes
- Label
- Transparencies
Loading Paper
Using the Multi-Purpose Tray
Multi-Purpose tray provides a convenient way to print envelopes, transparencies,
or other type of media without having to unload the other tray.
To load paper in the Multi-Purpose tray, proceed as follows.
1
Pull the Multi-Purpose tray
towards you.
2
Slide the length guide out toward
you.
P RINT M EDIA
4.1
Loading Paper
3
Flex the sheets back and forth
to loosen them, then fan them.
Notes: • Do not fold or crease the paper.
• Place the paper with the recommended print side face up.
4
Place the paper against the side
of the Multi-Purpose tray with
the recommended print side face
up and the top edge going in
first toward the printer as
shown.
5
Adjust the paper guide to the
size of the paper inserted by
pushing the guide.
4.2 P RINT M EDIA
Loading Paper
Using the Manual Feed
The Manual Feed feature allows you to print from the Multi-Purpose tray onto
special media such as envelopes or letterhead.
If the Tray menu item is set to Manual, the printer will print only from the
Multi-Purpose tray.
Manual Feed can be selected through the software or printer driver too.
1 Select Manual as the paper source.
• Set the source item in the properties dialogue box to Manual.
• You can select Manual as the paper source by setting the Tray item
using the operator panel menu.
2 Print your document.
3 Place a sheet of paper in the
Multi-Purpose tray.
4 Press continue key when you are
prompted.
P RINT M EDIA
4.3
Loading Paper
Letterhead / Prepunched Paper
Special paper includes letterhead, prepunched, envelopes, labels,
and transparencies.
When printing letterhead and prepunched paper, it is important to load the trays
with the correct orientation.
For Multi-Purpose tray,
Load the paper with the side-to-beprinted facing up, and the top, short
edge toward the printer.
• Set the source item in the
properties dialogue box to
Manual or MP.
- To print continuously from
Multi-Purpose tray,
set the source item to MP.
- To print a sheet of paper from
Multi-Purpose tray,
set the source item to Manual.
Printing Side(up)
For ALL other trays,
Load paper with the side-to-beprinted facing down, and the top,
short edge toward you.
Printing Side(down)
4.4 P RINT M EDIA
Loading Paper
Envelopes
Many types of envelopes can be printed from the Multi-Purpose tray.
The types of envelopes are COM-10, MONARCH, DL, C5 and C6(60~90g/m2).
The printer will automatically feed up to 10 envelopes.
Printing performance depends on the construction of the envelope.
Printing information
• Set margins at least 0.6inch(15mm) from the edge of the envelope.
• Always test a few sample envelopes before purchasing large quantities.
• Select THICK paper for better quality.
Envelopes guidelines
For best performance, use envelopes made from 75g/m2(20lb bond) paper.
Do not use envelopes that :
• Are damaged in any way.
• Use metal claps, string ties, metal folding bars.
• Contain windows, holes, cutouts or embossing.
• Have exposed flap adhesive when the flap is in the sealed or closed
position. For envelope specifications, see page Appendix A.4.
Loading envelopes
1
Open the Multi-Purpose tray.
Pull out the extension.
P RINT M EDIA
4.5
Loading Paper
2
Load up to 10 envelopes in the
left side of Multi-Purpose tray
with the side-to-be printed
facing up, and the postage-end
toward the printer.
3
Adjust the guide to touch the
envelope stack without bending
the envelopes.
ng Samsu
4
Set the source item in the properties dialogue box to Manual or MP.
Notes: Do not use an envelope curled
down side, refer to the figure.
(Side View)
4.6 P RINT M EDIA
Loading Paper
Label
Labels automatically feed from the Multi-Purpose tray or the other trays.
Label guidelines
Make sure that labels meet the specifications for the tray you use.
• Use full label sheet. Partial sheets may cause labels to peel off during
printing, resulting in a paper jam.
• The adhesive material should be stable at 400OF(205OC), the printers
maximum temperature.
• Do not use labels that have the backing sheet exposed.
Notes: Do not print on both sides of labels.
Label orientation
• For Multi-Purpose tray, load the
labels with the side-to-be-printed
facing up, and the short edge
toward the printer. Print a stack of
25 labels from Multi-Purpose tray.
P RINT M EDIA
4.7
Loading Paper
Transparencies
Transparencies automatically feed from the Multi-Purpose tray or the other trays.
Some brand of transparencies may require manual feeding.
The Multi-Purpose tray is a tray that holds up to 25 sheets of A4 or Letter size paper.
Transparencies guidelines
• Use only transparencies recommended for use in laser printers.
• Place transparencies on a flat surface to cool after removing them from the
printer.
Transparencies orientation
• For Multi-Purpose tray, load the
transparencies with side-to-be-printed facing up, and the top toward the
printer.
Print a stack of 25 transparencies
from the Multi-Purpose tray.
Notes: • Because transparencies are heavier than paper,
do not load the trays to capacity.
• Remove each transparency from the output bin before
printing another.
4.8 P RINT M EDIA
Memo
Memo
P RINT M EDIA
4.9
5 Printing Tasks
This chapter explains your printing options and gives common
printing tasks.
Topics included in this chapter are:
◆ Using Features in the Printer Driver
- With Windows 95/98/NT 4.0/2000
◆ Using the Printer Driver
- Paper Tab
- Graphic Tab
- Output Tab
- Printer Tab
- Overlay Tab
- Watermark Tab
◆ Printing Both Sides of Paper
◆ Printing Multiple Pages on One Sheet of Paper (N-Up Printing)
◆ Printing Booklets
◆ Printing on Different Paper for the First Page
◆ Fitting Your Document To a Selected Paper Size
◆ Printing Posters
Using Features in the Printer Driver
When you print from a software application, many of the printer’s
features are available from the printer driver.
To change the settings from a software application, follow this procedure.
With Windows 95/98/NT 4.0/2000
1
Select Start-Settings-Printers from the Windows task bar.
2
Double-Click on the desired printer driver icon.
3
Select Printer-Properties.
4
Click on the appropriate tab.
5
Select the required options.
See page 5.9
See page 5.8
See page 5.6
See page 5.4
See page 5.11
See page 5.2
General
You can print a
test page and
view the driver
information.
Sharing
You can share the
printer.
Details
You can select the
printer port and spool
setting.
Notes: Changes made from a software application override the user default setting
made from the printer operator panel.
P RINTING TASKS
5.1
Using the Printer Driver
The features of the printer driver are organized under ten tabs :
Click on a tab at the top of the properties window to access one of the nine
dialog boxes.
Each tab of the properties box is described in this section.
Paper Tab
You can restore all the original settings of the PCL 6 printer
driver by clicking Defaults.
5.2 P RINTING TASKS
Using the Printer Driver
Copies
Use the Copies box to set the number of copies you
want to print.
Paper Orientation
Choose Portrait or Landscape to select the default
orientation of the printed page.
printable
area
œ
œ
Landscape
Portrait
Different Soruce for First Page
If the box is checked, this feature is enabled and the
dialog box allows you to select the desired paper
source for the First Page and Other Pages
independently.
If the box is empty, this feature is disabled.
Notes: The paper size for all pages of the print job
must be the same.
Paper Source
The source setting identifies the default paper tray.
Paper sizes
Use this setting to select the paper size.
Paper type
The Paper type setting lets you specify the type of
print material installed in each tray.
Important If you want to know more about each menu, click on the Help button.
The help screen gives detailed information about each menu.
P RINTING TASKS
5.3
Using the Printer Driver
Graphic Tab
The settings on the Graphic tab allow you to fine tune your image quality
and to balance print quality and print speed.
You can restore all the original settings of the PCL 6 printer
driver by clicking Defaults.
5.4 P RINTING TASKS
Using the Printer Driver
Resolution
Select from the available setting to set the maximum
resolution for your print jobs.
SRT Mode
Some printed characters or images can appear to have
jagged or uneven edges. Set this Samsung Resolution
enhancement Technology (SRT) option to improve the
print quality of your text and image and to make the
characters and images appear smoother.
Notes: SRT Mode is disabled when 1200 dpi settings are
selected.
Toner Save Mode
This determines the amount of toner to be used while
printing a page. The printer uses 50% less toner when
Toner Save Mode is selected.
Graphic Mode
This setting allows you to change the Graphic Mode.
Halftoning
This setting lets you fine-tune the way colors in graphic
images are converted to gray dot patterns.
Important If you want to know more about each menu, click on the Help button.
The help screen gives detailed information about each menu.
P RINTING TASKS
5.5
Using the Printer Driver
Output Tab
You can restore all the original settings of the PCL 6 printer
driver by clicking Defaults.
5.6 P RINTING TASKS
Using the Printer Driver
Pages per Sheet(Multiple Images)
Use the Pages per Sheet setting to print
multiple pages on a single sheet of paper.
• You can fit 1, 2, 4, 6, 9 or 16 pages
on a single sheet of paper.
For example, 2 means two page images are
printed on one page.
• The print page borders setting determines
whether a border is printed around each
page image.
Duplex
Use the Duplex box when you want to print on
both sides of the paper. See page 5.13.
Important If you want to know more about each menu, click on the Help button.
The help screen gives detailed information about each menu.
P RINTING TASKS
5.7
Using the Printer Driver
Printer Tab
Printer Memory
Select the value of the printer
memory installed in the printer.
After adding more memory, set
the value of the printer memory.
Important If you want to know more about each menu, click on the Help button.
The help screen gives detailed information about each menu.
5.8 P RINTING TASKS
Using the Printer Driver
Overlay Tab
An overlay is text and/or images stored in the computer HDD as a special file
format that can be printed on any document you choose.
Overlays are often used to take the place of preprinted forms
and letterhead paper.
P RINTING TASKS
5.9
Using the Printer Driver
Overlay List
The file is now shown in the Overlay List
box and is available for printing.
Select the overlay from the Overlay List
box.
Create Overlay
To use a page overlay, you must create a
new page overlay containing your logo or
image.
Load Overlay
If you have stored the overlay file you
want to use into an external source, you
can also load the file when you access this
Load Overlay window.
Important If you want to know more about each menu, click on the Help button.
The help screen gives detailed information about each menu.
5.10 P RINTING TASKS
Using the Printer Driver
Watermark Tab
A Watermark is text that is superimposed on your final output.
Usually in a lighter gray you can create a watermark with your own text.
P RINTING TASKS
5.11
Using the Printer Driver
Message
You can select a watermark from the
message list.
Edit
Use this dialog box to enter the text
and layout of your watermark.
You can set the watermark’s font, size
and darkness, as well as the angle and
position on the page.
The preview area shows the effect of
your settings.
Important: If you want to know more about each menu, click on the Help button.
The help screen gives detailed information about each menu.
5.12 P RINTING TASKS
Printing Both Sides of Paper
The printer can automatically print on both sides of paper by setting the
Printing Menu or Output tab of the Samsung ML-7300 PCL 6 Driver.
Notes: • Do not print on both sides of labels, transparencies, envelopes, or paper
heavier than 24lb. Damage to printer and paper jamming might result.
• For duplex printing, it is recommended to print less than 1,500 pages a day
to keep a good image quiality.
Place the paper against the left side of the Tray (See page 5.15).
1
2
3
4
Open the document to be printed in the appropriate application.
Click on the Print button.
Click on Properties.
Click on the Output tab.
Result: The Output tab is displayed.
5
Set the Duplex item to Short Edge or Long Edge,
and select the source item.
Long Edge
Short Edge
P RINTING TASKS
5.13
Printing Both Sides of Paper
Menu Setting
If you use a driver which does not have a properties box.
you can select ‘DUPLEX’ by using the control panel menu.
1
2
Make sure the READY message appears on the display.
Press On Line.
Result: The ‘OFFLINE’ message appears on the display and the printer is off-line.
3
4
5
Press Menu until you see PRINTING MENU.
6
Press Enter to save the selection.
Press Item until you see DUPLEX.
Press Value until the setting you need appears on the display
(For more information, see page 3.8).
Result: An asterisk(❊) appears beside the current user default
setting for that menu item.
Notes: Settings in the printer driver and software
application override operator panel settings.
5.14 P RINTING TASKS
Printing Both Sides of Paper
Paper Orientation for Printing both sides of Paper
The printer prints the second sides of paper first, so paper such as letterhead
and preprinted paper needs to be oriented as illustrated in the figure below.
For Multi-Purpose tray
Load the first side facing down and
the top toward you.
• Set the source item in the
properties dialogue box to
Manual or MP.
- To print continuously from
Multi-Purpose tray, set the source
item to MP.
Multi-Purpose Tray
- To print a sheet of paper from
Multi-Purpose tray,
set the source item to Manual.
For all other Trays
Load the first side facing up and
the top toward the printer.
Tray
P RINTING TASKS
5.15
Printing Multiple Pages on
One Sheet of Paper
1
2
3
4
(N-Up Printing)
You can select the number of pages you want to print on a
single sheet of paper. If you choose to print more than one
page per sheet, the pages will appear decreased in size and
arranged on the sheet. You can specify up to 16 pages.
1 When you change the print settings from your software
application, access the printer properties. See page 5.1 to
access the printer properties.
œ 4 pages per sheet
From the Paper tab, select the paper orientation, source,
size and type.
1
4
2 Click the Output tab, and choose Multiple Pages per
5
2
6
3
Side in the Type drop-down list. Then select the number of
pages you want to print per sheet (1, 2, 4, 6, 9 or 16) in
the Pages per Sheet drop-down list.
3 Click Print Page Borders if you want to print a border
œ 6 pages per sheet
around each page on the sheet. Print Page Borders is
enabled only if Pages per Sheet is 2, 4, 6, 9, or 16.
4 Click OK, then start printing.
5.16 P RINTING TASKS
Printing Booklets
Booklet printing feature allows you to print your document as
a 2-sided (duplex) job and arrange the pages so that the
paper can be folded in half after printing to produce a booklet.
9
8
1 When you change the print settings from your software
œ
Portrait orientation
application, access the printer properties. See page 5.1 to
access the printer properties.
From the Paper tab, select the paper orientation, source,
size and type.
1
97
œ
Notes: For booklet printing, only four paper sizes are
supported: Letter, A4, Legal, and Executive.
Landscape orientation
2 Click the Output tab, then choose Booklet Printing from
the Type drop-down list.
When you select Booklet Printing, the Duplex option
automatically changes to Short Edge. This setting is
required to format the printed pages correctly.
6
3
8
1
œ 8-page document
8
9
3 Print the document.
4 Fold and staple the pages.
P RINTING TASKS
5.17
Printing on Different Paper for the First Page
1 When you change the print settings from your software
application, access the printer properties. See page 5.1 to
access the printer properties.
2 Click the Paper tab, and click Different Source for First
Page.
If the box is checked, this feature is enabled and the dialog
box allows you to select the desired paper source for the
First Page and Other Pages independently. If the box is
empty, this feature is disabled.
3 Click OK, then start printing.
Notes: The paper size for all pages of the print job must
be the same.
5.18 P RINTING TASKS
Fitting Your Document To a Selected Paper Size
A
This printer feature allows you to scale your print job to any
selected paper size regardless of the digital document size.
This can be useful when you want to check fine details on a
small document.
1 When you change the print settings from your software
application, access the printer properties. See page 5.1 to
access the printer properties.
2 Click the Output tab, and select Fit to Page in the Type
drop-down list.
3 You’ll see the Application page size and be prompted to
select the Fit to Paper Size. Select the correct size from
the drop-down list.
4 Click OK, then start printing.
P RINTING TASKS
5.19
Printing Posters
This feature allows you to print a single-page document onto
4, 9, or 16 sheets of paper, which can be pasted together to
form one poster-size document.
1 When you change the print settings from your software
application, access the printer properties. See page 5.1 to
access the printer properties.
From the Paper tab, select the paper orientation, source,
size and type.
œ
Poster printing
with 2x2 style
5.20 P RINTING TASKS
2 Click the Output tab, and select Poster in the Type
drop-down list.
Printing Poster
3 To determine the scaling factor, select the Style; 2x2, 3x3,
4x4 or Custom.
For example, if you select 2x2, the output will be
automatically stretched to cover 4 physical pages.
If you select Custom, you can adjust the scaling factor
manually. For example, if you specify 150%, the image will
be printed across 4 pages with 150% scaled.
➛ Custom (150%)
➛ 2 x 2
4 You may specify an overlap in pixel to make it easier to
reconstruct the resulting poster.
25 pixels
25 pixels
œ Overlap=0
œ Overlap=25
5 Click OK, then start printing.
P RINTING TASKS
5.21
6 Maintaining
Your Printer
This chapter provides suggestions for high-quality
and economical printing and information for
maintaining the toner cartridge and the printer.
Topics included in this chapter are:
◆ Toner Cartridge
◆ Cleaning the Printer
◆ Cleaning LSU
Toner Cartridge
Toner cartridge storage
Do not remove the toner cartridge from its package
until you are ready to use it.
Notes: To prevent damage to toner cartridge,
do not expose it to light.
Toner cartridge life
The life of the toner cartridge depends on the amount
of toner that print jobs require.
When printing text at 5% coverage, a Samsung toner
cartridge lasts an average of 10,000 pages in simplex
mode, depending on which toner cartridge is installed.
This assumes that print DENSITY and ECONO menu
items are set to default.
Distributing the Toner
When toner is low, faded or light area might appear
on a printed page.
You might be able to temporarily improve print quality
by distributing the toner.
M AINTAINING Y OUR P RINTER
6.1
Toner Cartridge
Redistributing Toner
When toner is low, faded or light areas may appear on a printed page.
You may be able to temporarily improve print quality by redistributing the
toner. The following procedures may allow you to finish the current print job
before replacing the toner cartridge.
1
Open the top cover by pushing
the button on the side of the
printer.
2 Remove the toner cartridge
from the printer.
CAUTIONS:
• Avoid reaching too far into
the printer. The fusing area
may be hot.
• To prevent damage to the
toner cartridge, do not
expose it to light for more
than a few minutes.
6.2 M AINTAINING Y OUR P RINTER
Toner Cartridge
3
Gently shake the toner cartridge
from side to side 5 or 6 times to
redistribute the toner.
Notes: If the toner gets on your
clothing, wipe it off with a dry cloth
and wash clothing in cold water.
Hot water sets toner into
fabric.
4
Reinsert the toner cartridge into
the printer. Be sure that the
toner cartridge is firmly in its
place.
5
Firmly close the cover.
If the print remains light
Remove the old cartridge and
install a new toner cartridge.
See “Installing Toner Cartridge”
on page 2.3.
M AINTAINING Y OUR P RINTER
6.3
Cleaning the Printer
To maintain print quality, you should clean the
• Never use alcohol or solvent based cleaning
as they may damage the printer casing and
• Never use a hard-bristled brush or abrasive
printer.
agents to clean the printer
components.
pad.
To clean your printer, proceed as follows.
1
Check that the printer is powered off and disconnected from the
power point.
2
Remove the paper from
Multi-Purpose tray.
3
Open the top cover and remove
the toner cartridge.
6.4 M AINTAINING Y OUR P RINTER
Cleaning the Printer
4
Use a soft cloth to remove any
dust.
5
If the outer casing or the paper feed guides are dirty, clean them with
a soft, clean cloth, slightly dampened with a gentle detergent.
6
Clean the inside of the printer with a damp cloth.
7
Replace the toner cartridge, close the top cover, plug in the power
cord, and turn the printer on.
Notes: While cleaning the printer, be careful not to touch the transfer
roller(the black, rubber roller, located underneath the toner cartridge).
Skin oils on the roller can cause print quality problems.
M AINTAINING Y OUR P RINTER
6.5
Cleaning LSU
To obtain high quality from your printer, clean the LSU(Laser Scanning Unit)
when characters have lines running through them.
1 Open the top cover and remove the toner cartridge.
2 Pull up on the LSU cleaner and put it on the LSU.
3
Slide the LSU cleaner
horizontally across a track on
the top of the LSU.
Notes: For more information on using method, see
attached label on the inside of the top cover.
6.6 M AINTAINING Y OUR P RINTER
Memo
Memo
M AINTAINING Y OUR P RINTER
6.7
7 Problem Solving
This chapter gives helpful information for
what to do if you encounter a printer error. It
provides information on the following topics:
◆ Clearing Paper Jams
◆ Error Messages
◆ General Printing Problems
◆ Poor Print Quality
◆ PS(PostScript) Problems
◆ Network Problems
◆ Macintosh Problems
Clearing Paper Jams
If the printer’s operator panel displays a paper jam message, look for paper in
the locations indicated in the figure below, then perform the procedure for
clearing the paper jam.
Notes: Be very careful not to tear the paper, when clearing paper jams.
If a small piece of paper is left in the printer, it could cause additional jams.
Paper Jam Locations
P ROBLEM S OLVING
7.1
Clearing Paper Jams
Problem
‘PAPER JAM0’
message appears
on the LCD
Solution
1
Slide the tray out
of the printer, and
remove any damaged paper from
the tray.
Notes : If the edge of the paper is visible in the
feed area, slowly pull the paper down
and out of the printer.
2 Make sure the
paper is below
the tab on the
guide.
3 Replace the tray.
4 Open and close the top cover to clear the
paper jam message.
7.2 P ROBLEM S OLVING
Clearing Paper Jams
Problem
Solution
‘PAPER JAM1’ or
‘PAPER JAM2’
messages appear
on the LCD
Check 1
• Open and close the top cover.
The paper comes out of the printer.
Check 2 (JAM 1)
• Open the top cover and
remove the toner
cartridge.
• Slowly pull the paper
out of the printer.
Do not tear the paper.
• Replace the toner
cartridge, and close the
top cover.
Check 3 (JAM 2)
• Open the rear cover.
• Grasp both sides of the
paper, and slowly pull
the paper out of the
printer.
Check 4
• Open and close the top cover to clear the paper
jam message.
Notes: The paper jam locations for both sides printing are different
from those of normal printing. Refer to page 7.1.
P ROBLEM S OLVING
7.3
Clearing Paper Jams
Problem
‘DUPLEX JAM 1’ or
‘DUPLEX JAM 2’
messages appear
on the LCD
Solution
Check 1
(DUPLEX JAM 1)
• Open the rear cover.
• Grasp both sides of
the paper, and slowly
pull the paper out of
the printer.
Check 2 (DUPLEX JAM 2)
• Pull the tray completely out
of the printer.
• Pull down the metal plate
inside of the printer.
• Slowly pull the paper
out of the printer.
7.4 P ROBLEM S OLVING
Error Messages
The following table explains messages that might display on the printer
operator panel.
Message
Meaning and Requried Action
A cover is open.
• Close the cover.
The Toner cartridge is not installed properly, or is not
SAMSUNG-approved cartridge. Open the top cover and
install the cartridge properly. If the proplem persists,
please contact your service representative.
The printer is running out of toner.
Purchase a new cartridge and replace the toner
cartridge.
The toner is low. The TonerLow menu item is set to STOP.
• Purchase a new cartridge and replace the toner cartridge.
• Set the Toner Low menu item to CONTINU.
• Press the Continue button.
The printer detects a paper jam. Open the cover and
remove the jammed paper, refer to page 7.2
for more information.
The printer detects a paper jam while printing both
sides of paper.
• Open the cover and remove the jammed paper.
Load the paper to clear the message.
P ROBLEM S OLVING
7.5
Error Messages
Message
Meaning and Requried Action
The requested paper size does not correspond
with the loaded paper size in the displayed tray.
Press Continue key.
Load the paper into the Multi-Purpose tray.
An internal error has occurred.
• Turn the printer off, and then turn the printer on.
• Contact your local dealer or after-sales service.
Data which was too complex was sent to the
printer.
• If this message persists, expand the memory.
The program in the memory has been damaged
in someway.
• Contact your local dealer.
7.6 P ROBLEM S OLVING
Error Messages
Meaning and Requried Action
Message
The printer detects a serial interface error.
●
Set the same Baudrate.
There is not enough memory in the printer.
●
You might want to add more memory to the
●
printer.
Check that the SMET menu item is set to ON.
The 1ST TRAY is open.
Close the 1ST TRAY to clear the message.
The OPT TRAY is open.
Close the OPT TRAY to clear the message.
The 1ST TRAY is open, but you can print
through MP TRAY.
Close the 1ST TRAY to clear the message.
The OPT TRAY is open, but you can print through
1ST tray or MP tray.
Close the OPT TRAY to clear the message.
P ROBLEM S OLVING
7.7
General Printing Problems
Problem
Solution
The power does not
• Check the power cord connections.
turn on.
• Check that the power supplied to the printer is
steady and meets printer specifications.
The printer does not
operate by pressing
the button on the
operator panel.
• Turn the printer off, and then turn the
It cannot print from
1 Select START ➔ Settings ➔ Printers from
software applications.
printer on.
Windows task bar (See page 5.1).
2 Click on the PCL 6 or PS printer icon.
3 Select File ➔ Default Printer.
The printed data is
not sent to the
printer.
• Check the printer cable connections
The test page is
• Check that all trays are properly loaded,
not printed.
(See page 2.8).
• Check the printer port on your computer.
adjusted, and installed in the printer.
• Check that all covers are correctly closed.
7.8 P ROBLEM S OLVING
Poor Print Quality
Problem
Solution
The vertical lines are
printed on the page.
Print is too light.
• Distribute the toner in toner cartridge (See page 6.1).
There are toner
• Print a few more pages to see if the problem
speckles.
• Adjust the ‘Density’ menu item setting (See page 3.12).
• Clean the inside of the printer (See page 6.4).
will correct itself.
• Clean the inside of the printer (See page 6.4).
• Check the paper type and quality.
The printer
• Check the paper type and quality.
drops letters.
• Check the printers environment.
• Install a new toner cartridge.
• Check the printer cable connections.
Dirty spots on the
• Heavy printing may lead to toner accumulationg
back side of paper
on the pressure foller of the fuser assembly. The
accumulated toner may melt and transfer onto
the back side of the paper.
of fuser ass’y
contamination.
• Select ‘FUSER CLEAN’ in the JOB MENU.
• Selecting ‘FUSER CLEAN’ will rotate the motor
for about 10 seconds and print one page of a
specified pattern for fuser cleaning and then stop.
P ROBLEM S OLVING
7.9
PS(PostScript) Problems
Problem
The Error messages
(This job contains
binary data...) are
printed.
The Optional Tray2 is
not selected in PS
Solution
1
2
3
4
Open the Properties of PS driver.
Click on PostScript.
Click on the Advanced button.
The pure binary data is not supported.
Choose the others.
1 Open the PS driver Properties.
2 Set ‘Optional Tray 2’ item of Device Option to
installed.
driver.
Network Problems
Problem
You cannot see any of
DHCP server, BOOTP
Solution
There are two methods.
• On the printer front panel, you can set IP
server or RARP server,
address in Network Menu. You can find the
when you want to set IP
following menu.
address to print server.
”NETWORK MENU ➜ CFG NET ➜ TCP/IP ➜
CFG TCP ➜ CFG ADRS”
7.10 P ROBLEM S OLVING
Macintosh Problems
Problem
Solution
The printer driver
icon does not appear
in the Chooser
dialogue box.
• LaserWriter 8.x driver should be installed in Mac
OS. Check that it is in the Extensions
folder under the System folder. If not, install
LaserWriter 8.x driver.
• Make sure that you use the standard cable.
• Make sure that the printer is connected to the
proper network.
Check AppleTalk in the Control
Panel on the Apple menu.
Your printer name
does not appear in
the Chooser dialogue
box.
• Make sure that the printer is turned on and
‘READY’ appears in the display.
• Check that the LocalTalk cable is
completely plugged into both the printer and your
Macintosh computer.
• Make sure that AppleTalk in Chooser is active.
The printer driver
does not automatically
setup the printer
when you click Auto
Setup in the Printer
Setup window.
• Reinstall the printer software.
See ‘Installing Software’ on page Appendix B.1.
P ROBLEM S OLVING
7.11
Appendix
A Specifications
This appendix provides information on the following
topics:
◆ Printer Specifications
◆ Paper Specifications
Printer Specifications
Controller
Characteristic
CPU
Description
Power PC, 100MHZ
Emulations
• Default: PCL 6, PS 3
• 16MB Standard
Memory
• Max up to 208MB
Interface
• IEEE 1284 B type
• Option:
Serial RS-232C/LocalTalk
Serial RS-232C/IrDA
Infrared Adapter Connector
Network
Font
45 Scalable font, 1 Bitmap
N/W Card
• Ethernet 10/100 base Tx
- SNMP in MIB
- TCP/IP
- Netware, Windows, Unix, Mac
Device Driver
PCL: Windows 95/98/NT 4.0/2000
*PostScript 3 Emulation
IPS-PRINT_Printer language Emulation© Copyright
1995-2000, Oak Technology, Inc., All rights reserved
S PECIFICATIONS
A.1
Printer Specifications
Enginge
Characteristic
Description
Speed
21 PPM (Letter size)
Resolution
1200 DPI + SRT
Imaging
Eletrophotography
Toning/Fusing
Non-mag monocomponent/contact
WarmUp time
Less than 70 secs
FPOT
Less than 12 secs
Size(WDH)
427 ✕ 449 ✕ 301(W ✕ D ✕ H)mm
Weight
Less than 16.5kg
Power Rating
AC 100 ~ 127 V (USA, Canada)
AC 220 ~ 240 V (Others), 50/60 Hz
Power Consumption
350W Printing Avg/ Max 34W printing sleep
Noise Level
Printing:
52dB
Standby: 36dB
Sleep: Background noise
Toner Cartridge
10,000 pages Avg at 5% coverage
In duplex mode, less than 10,000 pages
Cable
Characteristic
A.2 S PECIFICATIONS
Description
Parallel
IEEE 1284
Serial
RS-232C
LocalTalk(RS-422)
IrDA
RS-232C
IrDA
Printer Specifications
Paper Handling
Characteristic
Description
Input Capacity
500 sheets - Tray 1
Optional Input
500 sheets(40 envelopes) - Optional Tray 2
Output Capacity
250 sheets Facedown
MP Tray
100 sheets(10 envelopes)
Type of Media
• Tray 1 : A4, LTR, Folio, Legal, Exec,
ISO B5, JIS B5 (16~24lbs)
• Multi-Purpose Tray :
A4, LTR, Folio, Legal, Exec,
Statement, ISO B5, JIS B5, A5,
A6, OHP, Label, COM-10, MON,
DL, C5, C6
• Tray 2 : A4, LTR, Folio, Legal : (16 - 24 lbs)
COM-10, MON, DL, C5 : (20 lbs)
Duplexing
• Paper : A4, LTR, Folio, Legal : (20 - 24 lbs)
Environment
Characteristic
Temperature
Description
Operating: 10 OC ~ 30 OC
Storage: 0 OC ~ 35 OC
Humidity
Operating: 30% ~ 80%
Storage: 10% ~ 90%
Others
Characteristic
Control Panel
Package Weight
Description
●
8 ✕ 2 LCD
●
LCD Display angle adjusting
●
Backlighting
●
Paper: 3 kg
●
Plastic: 0,7 kg
S PECIFICATIONS
A.3
Paper Specifications
Acceptable paper size for all trays
The following table gives details about the print material you can load
into each of the printer trays.
Paper size
Tray1
Optional
Tray2
Multi-Purpose
Tray
A4
210 ✕ 297 (8.3✕11.7”)
●
●
●
●
LETTER
216 ✕ 279 (8.5✕11”)
●
●
●
●
FOLIO(LEGAL 13”)
216 ✕ 330 (8.5✕13”)
●
●
●
●
LEGAL(LEGAL 14”)
216 ✕ 356 (8.5✕14”)
●
●
●
●
EXECUTIVE
191 ✕ 267 (7.3✕10.5”)
●
●
●
STATEMENT
140 ✕ 216 (5.5✕8.5”)
ISO B5
176 ✕ 250 (6.9✕9.9”)
●
●
●
JIS B5
182 ✕ 257 (7.2✕10”)
●
●
●
A5
148 ✕ 210 (5.8✕8.2”)
●
A6
105 ✕ 148
●
ENVELOPE
- COM-10
- MONARCH
- DL
- C5
- C6
105 ✕ 241(4.12✕9.5”)
98 ✕ 191(3.87✕7.5”)
110 ✕ 220(4.33✕8.66”)
162 ✕ 229(6.38✕9.01”)
114 ✕ 162(4.49✕6.38”)
TRANSPARENCY
- A4
- LETTER
210 ✕ 297
216 ✕ 279(8.5✕11”)
●
●
LABEL
- A4
- LETTER
210 ✕ 297
216 ✕ 279(8.5✕11”)
●
●
Paper
●
●
●
●
●
PAPER CAPACITY
- CUT SHEET
- ENVELOPE
- LABEL
- TRANSPARENCY
A.4 S PECIFICATIONS
●
●
●
●
●
●
A6(INTERNATIONAL 100 ✕ 148
POST CARD)
PAPER WEIGHT
- CUT SHEET
- ENVELOPE
Duplex
16-24lb
16-24lb
16-20lb
16-43lb
16-24lb
500
(20lb)
500(20lb)
40(20lb)
100
10
25
25
20-24lb
Paper Specifications
Supported Types of Paper
The printer supports the following types of paper :
•
•
•
•
Plain
Letterhead
Bond
Rough
•
•
•
•
Prepunched
Preprinted
Color
Recycled
• Transparency
• Labels
• Card Stock
Guidelines for Using Paper
Make sure the paper is good quality
Labels
To avoid damaging the printer, use only labels recommended for use in
laser printers.
• The adhesive material should be stable at 400OF(205OC), the printer’s
maximum temperature.
Transparencies
To avoid damaging the printer, use only transparencies recommended
for use in laser printers.
• Transparencies used in the printer must be able to withstand
400OF(205OC), the printers maximum temperature.
S PECIFICATIONS
A.5
Appendix
B
Macintosh User’s
Guide
You can use the printer to print a document from a Macintosh
via a Serial LocalTalk interface or an optional network interface.
Topics included in this appendix are:
◆ Setting Up Your Printer
◆ Installing Software
◆ Printing with a Macintosh
Setting Up Your Printer
Installing Serial/LocalTalk Option Card
For instructions on installing the Printer Options,
see appendix F, “Installing Serial/LocalTalk or
Serial/IrDA option card”.
Installing Network Printer Card - PortThru (for Network Printing only)
For instructions on installing the Printer Options,
see appendix F, “Network Option Card”.
Installing Software
The following system requirements are necessary in
order to connect a Macintosh computer to the
printer.
• Mac OS 7.5 or higher
• Macintosh LaserWriter 8.x printer driver
• ML-7300 PostScript PPD
Installing LaserWriter Printer Driver
The LaserWriter 8 printer driver is standard to the
Mac OS 7.5 and higher.
Check the Macintosh Chooser to assure that it is
installed.
If it isn’t, use the Mac OS help system for
information about installing it.
M ACINTOSH U SER ’ S G UIDE
B.1
Installing Software
Installing the PS Driver
Make sure the ‘READY’ message appears on the
operator panel display.
1 If necessary, press the power button on the
Macintosh computer.
2 Insert ML-7300 CD.
3 Select the correct language and double-click the
Installer icon.
Then follow the instructions on the screen.
4 From the Apple menu, choose Control Panel,
then double-click AppleTalk.
The AppleTalk dialog box appears.
5 From the Connect Via drop-down list,
select Printer Port if connecting with a LocalTalk
cable, or select Ethernet
if using a network connection.
B.2 M ACINTOSH U SER ’ S G UIDE
Installing Software
Notes: If the computer is connected to a network,
selecting Printer Port will disconnect
communication with the network. If you select
LocalTalk, the Samsung ML-7300 printer
appears in the Chooser box.
6
From Chooser on the Apple menu,
select LaserWriter 8.x icon. The name of your
printer appears in the right pane of the window.
The name by default will be Samsung 010001
(Samsung followed by DDP address in
Hexadecimal).
M ACINTOSH U SER ’ S G UIDE
B.3
Installing Software
7 Click on your printer name.
8 Click the Create button if it appears.
The installation is completed. You don’t need
to proceed with the following steps.
Notes: These steps appear with some driver
versions.
9 Click on the Setup button.
10 Select Auto Setup button. The Samsung
ML-7300 file is installed automatically and
the Samsung ML-7300 printer icon appears
on the desktop.
Important: If Auto Setup fails,
click ‘Select PPD’ and choose
Samsung ML-7300 file.
11 Make sure the Samsung ML-7300 file is
installed correctly. Click on the OK button,
then close Chooser.
Notes: Keep the original CD-ROM in a safe place.
B.4 M ACINTOSH U SER ’ S G UIDE
Printing with a Macintosh
Printing from Macintosh
1 Start the necessary application and open the
document you want to print.
2 From Chooser in the Apple menu, select
LaserWriter 8, then your printer name.
3 From the File menu, select Page Setup. The
Page Setup dialog box appears.
4 After making any necessary changes to the
page setup, click OK.
See page Appendix B.6 for more information
about Page Setup.
5 From File, select Print to open the Print
dialog box.
6 Make any necessary changes to the print
settings, then click Print.
See page Appendix B.8 for more information
about Print settings.
7 Your printer starts printing.
M ACINTOSH U SER ’ S G UIDE
B.5
Printing with a Macintosh
The Page Setup Dialog Box
When you select Page Setup from the File menu of your
application, a dialog box will appear.
Notes: The Page Setup dialog box may differ depending
on the application and LaserWriter version you are
using.
Page Setup Features
Paper
: Select the paper size you want to use.
Layout
: Sets the number of pages to be printed on each sheet.
Reduce or Enlarge
: To print a reduced or enlarged copy of your document,
type a percentage of reduction or enlargement.
Orientation
: To set up your document so that it is oriented for
Portrait (tall) or Landscape (wide) printing, click one of
these icons.
B.6 M ACINTOSH U SER ’ S G UIDE
Printing with a Macintosh
To display additional LaserWriter settings, click the Options
button. The window as shown below appears.
Visual Effects
Flip Horizontal
: To print a mirror image of the document,
click this check box.
Flip Vertical
: To print the document upside down,
click this check box.
Invert Image
: To print white area of the document as black and black
area as white, click this check box.
Printer Options
Substitute Fonts
: To let the printer substitute fonts during printing,
click this check box.
Smooth text
: To improve printed bitmapped fonts,
click this check box.
Smooth Graphics
: To improve printed graphic images by smoothing jagged
edges, click this check box.
Precision Bitmap Alignment
: To print improved bitmapped images, click this check box.
Larger Print Area (Fewer Downloadable Fonts)
: To print on more of the page, click this check box.
Unlimited Downloadable Fonts In a Document
: To use a large numberof Fonts in a document,
click this check box.
M ACINTOSH U SER ’ S G UIDE
B.7
Printing with a Macintosh
The Print Dialog Box
When you select Print from the File menu of your
application, you will see the dialogue box as shown below.
Notes: The Page Setup dialog box may differ depending
on the application and LaserWriter version
you are using.
Print Features
Copies
: Type the number of copies to be printed
Pages
: To print all your pages, click All.To print only some
pages, type the first page number in the From box
and type the last page number in the To box.
Paper Source
: Use these buttons and menus to select the paper
source you want to use.
Destination
: Use these buttons to send your document to the
printer or to save it as a PostScript file.
B.8 M ACINTOSH U SER ’ S G UIDE
Printing with a Macintosh
To display additional printer settings, click the Options
button. The window as shown below appears.
Print Options Features
Cover Page
: Prints a cover page as the first or last page of the
document, or turns off the printing of a cover page.
Print
: Sets a document for printing in black and white, in
color, or shades of gray, or using ColorSync
matching or PostScript matching.
Print Profile
: Sets a document to be printed using the color
characteristics of a specific printer.
PostScript™ Errors
: Provides options for reporting PostScript errors
that occur during printing.
Choose Resolution
: Selects print resolution.
Duplex
: Sets binding direction for duplex printing,
or turns off duplex printing.
M ACINTOSH U SER ’ S G UIDE
B.9
Appendix
C
Using Windows
PostScript Driver
If you want to use the PostScript driver provided with your
system CD-ROM or diskettes to print a document, use the
information in this Appendix.
Topics included in this Appendix are:
• Installing PS Driver
Installing PS Driver
Important: • You must have the CD(or diskette) for “windows 95”
or Windows 98” available for use.
• You cannot use PS in Windows 3.1.
PPDs, in combination with the PostScript driver, access the
printer features and allow the computer to communicate
with the printer. An installation program for the PPDs is
provided on the ML-7300 CD-ROM.
Notes:
• Installing the PostScript printer driver may require
the use of the operating system files on the original
CD-ROM or diskette that came with your system.
• If you have a PostScript level 3 driver and want to
use it, you must install the PostScript level 3 PPD
which is also provided on the ML-7300 CD-ROM.
1 Before installing PPD files, make sure that the printer and
the PC are properly connected with parallel or optional
network interface. For information on:
• Connecting with parallel interface, see page 2.8.
• Connecting with an optional network interface,
see Appendix F, “Network Option Card”.
2 Insert the CD-ROM shipped with your printer into your
CD-ROM drive.
If the CD-ROM drive does not automatically run:
Select Run from the Start menu, and type
x:\cdsetup.exe in the Open box (where x is the
drive letter for the CD-ROM drive), then click OK.
U SING W INDOWS P OST S CRIPT D RIVER
C.1
Installing PS Driver
3 When the opening screen appears,
select the appropriate language.
4 Click Install the Samsung Software-II on your
PC (PostScript).
5 Click on HaveDisk, click Browse, then choose:
• for Windows 9x, x:\Eng(or the desired language
code. See page 2.17)\ps\Win95_98\level 2.
• for Windows NT 4.0, x:\Eng(or the desired language
code. See page 2.17)\ps\WinNT\level 2.
• for Windows 2000, x:\Eng(or the desired language
code. See page 2.17)\ps\Win2000.
where x is the drive letter for the CD-ROM drive,
then click OK.
6 Follow the instructions on the screen to complete the
installation.
C.2 U SING W INDOWS P OST S CRIPT D RIVER
Installing PS Driver
Selecting the Default Printer
1 Start Windows on your pc.
2 Select Start ➔ Settings ➔ Printers from the
Windows 95 task bar.
3 Double click the SAMSUNG ML-7300 PS
printer icon.
4 Select File ➔ Default Printer.
5 Print the document on your Samsung ML-7300 PS.
To set the PS driver features, proceed as follows
1 Double-click on the PS driver icon.
2 Select Printer ➔ Properties.
3 Select the required options.
U SING W INDOWS P OST S CRIPT D RIVER
C.3
Appendix
D
Using the Printer
on a Network
If you work in a networked environment, the printer can be
shared by other users on the network. ML-7300N printer is
a network printer and can be connected to the network via
direct attachment to an external print server.
This appendix provides information on the following topics:
◆ About sharing the Printer on a Network
◆ Setting Up a Locally Shared Printer
◆ Setting Up a Network-Connected Printer
About Sharing the Printer on a Network
If you work in a networked environment,
you can connect the ML-7300 series printer to your
network.
Locally Shared
You can connect the printer directly to a selected
computer (called the “host computer”) on the
network. The printer can then be shared by other
users on the network through a Windows 9x, 2000
or NT 4.0 network printer connection.
Network-Connect
If an option network card was installed on your
printer (see page Appendix F.8 for information on
installing the network option card in your printer)
or if you have ML-7300N printer, the printer can be
connected to the network via direct attachment to
an external print server.
Printing Across a Network
Whether the printer is locally connected or network
connected, you need to install the ML-7300 series
printer software on each computer that will print
documents to the ML-7300 series printer.
U SING
THE
P RINTER
ON A
N ETWORK
D.1
Setting Up a Locally Shared Printer
Setting Up Host Computer
1 Start Windows.
2 From the Start menu, select Control Panel,
and double-click on the Network icon.
3 Check the File and Print Sharing box, then click OK.
Close the window.
4 Click Start and select Printers from Settings,
then double-click your printer name.
5 Select Properties in the Printers menu.
6 Click the Sharing tab, then check the Shared As box. Fill
in the Shared Name field, then click OK.
Setting Up Client PC
1 Right-click Start, and select Explorer.
2 Open your network folder in the left column.
3 Right-click the shared name, and select Capture
Printer Port.
4 Select the port you want, check the Reconnect
at log on box, then click OK.
5 From the Start menu, select Settings, then Printers.
6 Double-click your printer icon.
7 From the Printers menu, select Properties.
8 Press the Details tab, select the printer port,
then click OK.
D.2 U SING
THE
P RINTER
ON A
N ETWORK
Setting Up a Network-Connected Printer
To use the ML-7300 Series printer as a Network printer,
you must install an optional network card in your printer.
See page F.8 for information on installing the network card.
If you have an ML-7300N printer, you do not need to install
the network card. The Samsung ML-7300N printer is shipped
with the network card.
After the network card is installed, you must set up
your printer as a network printer using the documentation and
Samsung SyncThru software provided with the network card.
U SING
THE
P RINTER
ON A
N ETWORK
D.3
Appendix
E
Installing
Software from
Diskettes
If you need to install the printer software on a system
that does not have a CD-ROM drive, use the instructions in
this appendix to create the software diskettes and install
the printer software from the diskettes.
This appendix provides information on the following topics:
◆ Making Installation Diskettes
◆ Installing Software from Diskettes
Making Installation Diskettes
If you do not have a CD-ROM drive and if you have access
to another computer with a CD-ROM drive, you can copy
software installation files from the your printer software
CD-ROM onto floppy diskettes, then use the diskettes
instead of the CD-ROM to install the software.
You can make the installation diskettes for PCL 6 driver,
PostScript Driver. Make sure that you have several
formatted diskettes ready, then follow these steps:
1 Insert the ML-7300 CD-ROM into the CD-ROM drive.
Install will start automatically.
If the CD-ROM drive does not automatically run:
Select Run from the Start menu, and type
x:\cdsetup.exe in the Open box (where x is the drive
letter for the CD-ROM drive), then click OK.
2 When the opening screen appears,
select the appropriate language.
3 Click Make your own Diskette set of software.
I NSTALLING S OFTWARE
FROM
D ISKETTES
E.1
Making Installation Diskettes
4 The Copy to Floppy dialog box appears.
Select the desired components you want to copy to the
diskette from the Select box. You can select PCL Printer
Driver, PostScript Driver.
Select the floppy disk drive you will use to
insert the diskette.
Select the
floppy drive you
will use.
Shows the
number of disks
required to copy
the selected
component.
Select the
component you
want to copy.
Shows the
path of the
selected
component.
5 Click Copy all disk images.
If you want to copy a portion of the selected component,
select the disk you want to copy in the Disk Images
window, then click Copy selected disk image.
6 When prompted, insert a blank, formatted diskette into
the floppy drive, and click Yes to copy the first diskette.
For multiple diskettes, when the first diskette is finished,
you are prompted to insert disk 2.
Make sure you label each diskette in order as you create it:
PCL Printer Driver, disk 1 of 2, etc.
E.2 I NSTALLING S OFTWARE
FROM
D ISKETTES
Making Installation Diskettes
7 If you have more than one disk, insert the next disk and
click Yes. Repeat this step for a third disk if necessary.
8 When the diskettes have finished copying, click Close in
the Copy to Floppy dialog box. Then click Exit in the
SAMSUNG PRINTER SETUP dialog box.
Installing Software from Diskettes
The instructions to install PCL Printer Driver, PostScript
Driver are same. Take the following steps:
1 Insert the first diskette (if the selected software diskettes
are more than one) which contains the desired
installation software; PCL Printer Driver, PostScript Driver.
2 From the Start menu, select Run.
3 Type A:\setup.exe in the Open box and click OK.
(if your floppy drive is not A, substitute the correct
letter).
4 Follow the on-screen instructions to complete the
installation.
I NSTALLING S OFTWARE
FROM
D ISKETTES
E.3
Appendix
F
Printer Options
Your printer is a full-featured laser printer that has been
optimized to meet most of your printing needs. Recognizing
that each user may have different requirements, however,
Samsung makes several options available to enhance the
printer’s capabilities.
This appendix provides information on the following topics:
◆ Precautions
◆ Preparations
◆ Closing The Printer Cover
◆ Understanding the Printer Control Board
◆ Printer Memory
◆ Network Option Card
(Installed in ML-7300N already)
◆ Installing Serial/LocalTalk or
Serial/IrDA option card
◆ Serial/LocalTalk
◆ Serial/IrDA
◆ Optional Tray 2
Precautions
Disconnect The Power Cord
Never remove the printer control board while the printer is
plugged in.
To avoid the possibility of electrical shock, always disconnect the
power cord when installing or removing ANY internal or external
printer option.
Discharge Static Electricity
The control board and internal printer options
(SIMM, Network interface) are sensitive to static electricity.
Before installing or removing an internal option,
discharge static electricity from your body by touching
something metal, such as the metal back plate on any device
plugged into a grounded power source.
If you walk round before finishing the installation, discharge any
static electricity again.
P RINTER O PTIONS
F.1
Preparations
Complete the following steps before you install the printer options.
1 Unplug the printer power cord.
2 Disconnect all cables from the back of the printer.
3
Remove the printer cover.
a Open the rear cover.
b Remove the two screws from
the back of the printer.
Save the screws.
c Grasp the cover
(as illustrated) and pull it
firmly toward the rear of the
printer until it stops.
d Remove the cover from the
printer.
e Remove the five screws from
the metal plate covering the
control board.
f Remove the plate.
F.2 P RINTER O PTIONS
Closing The Printer Cover
When you have finished installing an Option, follow these steps.
1 Close the metal plate and tighten
all the screws.
2 Set the bottom of the cover onto
the printer. Make sure the bottom
tabs on the cover fit into the
corresponding slots in the printer.
Rotate the cover up towards the
printer. Slide the cover toward the
front of the printer until it clicks
into place.
3 Gently tighten all the screws.
4
Reconnect any interface cables and the power cord.
P RINTER O PTIONS
F.3
Understanding the Printer Control Board
If the printer cover is opened,
you can see the printer control board as below.
ROM SIMM
Connector
Network Card
Connector
Printer Memory
Connector
F.4 P RINTER O PTIONS
Serial/LocalTalk
or Serial/IrDA
Connector
Printer Memory
The printer memory option increases the printer’s
dynamic random access memory (DRAM).
Your printer was shipped with 16MB of standard printer Memory.
You can install two printer memory options in your printer. Printer memory upgrade
options available are 4, 8, 16, 32, 64 and 128MB.
Notes: Your machine recognizes only half of 8MB, 32MB and 128MB SIMMs
if installed in the slot CN 4.
DRAM SIMM Features for Upgrade
- Speed(Access Time): 50nS
- Refresh Time: 1K(1024 cycles/16 ms) / 2K(2048 cycles/32 ms)
- The Method of refresh is CAS-befor-RAS refresh
- Mode: EDO Type
- Single +5V +/-10% power supply
- The SDRAM does not support
1 Before you install the printer memory option, follow steps under
‘Preparations’ on page F.2.
Notes: The printer memory option is easily damaged by static electricity.
Touch something metal before you touch the memory option.
2
Remove two screws and remove the metal plate in the direction
of the arrow.
Memory
Connector
CN 3
CN 4
CN 5
CN 4: This slot recognizes only half of 8MB,
32MB and 128MB SIMMs if they are installed.
P RINTER O PTIONS
F.5
Printer Memory
3 Unpack the memory option.
Notes: Avoid touching the connection
points along the edge.
Save the packaging.
4 Hold the memory option with the
connection points pointing toward
the connector and position the
notch as shown. Insert the
memory option all the way into
the connector at a 30 O
angle, and rotate it left until it
snaps into place.
5 Make sure both metal clips on the
connector are fastened, and the
two pins on each of the
connectors are pushed through
the holes on the memory option.
6 Continue with ‘Closing the Printer
Cover’ on page F.3.
7 Set the printer memory item on
the printer tab of the properties
dialogue box to the value of the
added printer memory.
F.6 P RINTER O PTIONS
Notch
Connection points
Printer Memory
Removing the Printer Memory Option
Complete the following steps if you need to remove a printer memory
option before you install a new one.
1 Push the metal clips at each end
of the connector away from
memory option.
2
3
Rotate the memory option right
to a 30 O angle and gently pull it
out of the connector as shown.
Place the printer memory option in its original packaging.
Notes: If you did not save the packaging, wrap the memory option in
paper and store it in a box.
P RINTER O PTIONS
F.7
Network Option Card
Overview
This chapter describes the proper preparations for network
printing. It contains the following information:
•
•
•
•
Package Contents
Installing Procedure
Connecting a Printer to the Network
Powering Up
Package Contents
When unpacking the network printer card,
you should find the following items.
Items Supplied
Network Printer Card
(PortThru)
Network Management
S/W User’s Guide
CD-ROM(SyncThru)
For ML-7300 Series
Network Brackets
Notes: Before installing the PortThru card to your printer,
you should attach one of the brackets above by using two
screws provided according to the type of your printer model.
You can check it with the picture of page F.9 which shows the
attached bracket to the PortThru card for ML-7300 Series.
F.8 P RINTER O PTIONS
Network Option Card
Installing Procedure
The network option card lets you connect the printer to a local area
network(LAN).You can install one network option card in your printer.
Card Connector Points
RJ-45 Port(Ethernet
10/100 Base T network)
1 Before you install the network option card, follow steps
under ‘preparations’ on page F.2.
2 Locate the card connector
on the printer control board.
Network card
connector
P RINTER O PTIONS
F.9
Network Option Card
3
Remove the two screws from the
metal plate covering the opening
for cable connector.
Remove the plate.
4 Unpack the option card.
5 Align the connector on the card
with the connector on the printer
control board. Push the card firmly
into the connector until it is
completely in place.
Result: The two connectors should fit
snugly together.
6
Gently tighten the screws to secure the card to the system board.
7
Continue with ‘Closing the Printer Cover’ on page F.3.
8
Install the network printer driver(called SyncThru) provided on
the CD-ROM. See Network Management Software User’s Guide for
installation.
F.10 P RINTER O PTIONS
Network Option Card
Connecting a Printer to the Network
Use standard network cabling that is used for other network components.
Make sure the printer is turned off before connecting the network cable to the port.
Attach the twisted-pair network cable to the RJ-45 port (10/100 Base T) on the card.
Powering Up
1 Connect the printer power cable into a properly grounded electrical outlet.
2 Turn on the printer.
top green
LED
bottom
green LED
Notes:
• The top green LED comes on when the cable is connected to the port on
the Network Printer Card.
• After booting, the bottom green LED should blink irregularly and the top
green LED should come on continuously. If the bottom green LED blinks
regularly, turn on your printer again.
P RINTER O PTIONS
F.11
Installing Serial/LocalTalk
or Serial/IrDA option card
1
Before you install the Serial/LocalTalk or Serial/IrDA option card,
follow steps under ‘Preparations’ on page F.2.
2
Locate the Serial/LocalTalk or Serial/IrDA connector on the printer
control board.
3
Remove the single screw that
fastens the metal plate covering
the cable connector opening.
4
Remove the plate.
5
Insert the Serial/LocalTalk or
Serial/IrDA option card into the
option card slot.
F.12 P RINTER O PTION
Installing Serial/LocalTark or Serial/IrDA option card
6
Align the connector on the card
with the connector on the printer
control board.
7
Push the card firmly into the connector until it is completely in place.
Notes: The two connectors should fit snugly together.
8
Gently tighten the screws to secure the card to the system board.
9
Continue with ‘Closing the Printer Cover’ on page F.3.
P RINTER O PTION
F.13
Serial/LocalTalk
Connecting the LocalTalk Cable
Connect the printer to your Macintosh using a LocalTalk cable.
Notes : A LocalTalk cable is not included.
It must be purchased separately.
Please contact your Macintosh dealer.
F.14 P RINTER O PTION
Serial/IrDA
You can use an infrared adapter to print remotely from an IrDA-Compatible
computer equipped with an infrared port.
The infrared port is compliant with the specifications established by the
Infrared Data Association(IrDA).
The infrared port operates transmitting data at speeds up to 115.200
bits per second.
Connecting the Infrared Apapter
1
Make sure the printer power
cord is unplugged.
2 Locate the infrared port
on the back of your printer.
3 Plug the adapter cable into the
infrared port.
4 Reconnect the power cord.
Result: The green light on the infrared adapter comes on
when the printer is plugged in.
P RINTER O PTION
F.15
Serial/IrDA
Using the Infrared Apapter
1 To print with an infrared port, you should install an infrared port driver
on your computer.
● If you do not have the driver, please ask your PC manufacturer.
● You can download the infrared driver for Windows 95 from the internet
with no charge (http://www.microsoft.com).
2 Aim the computer infrared port at the infrared port on the back
of the printer.
3 Aim the infrared port on your computer within 15 degrees of
either side of the line as shown.
4 The printer must be within 3 feet(1 meter) of the computer.
5 Make sure the printer is in ready state.
6 Send the print job from the computer.
F.16 P RINTER O PTION
Optional Tray 2
You can install an Optional Tray 2 Complete the following steps beforeyou
install the Optional Tray 2.
●
●
Unplug the printer power cord.
Disconnect all cables from the back of the printer.
1 Carefully place the printer on
top of the Optional Tray 2 unit.
●
Make sure the connector is
properly inserted.
2 Reconnect all cables to the back of the printer.
3 Reconnect the power cord to the printer.
4 Make sure the ‘READY’ message appears on
the operator panel display.
P RINTER O PTION
F.17
Optional Tray 2
Loading the plain Paper into the Optional Tray 2
Your printer has an optional cassette that can hold up to 500 sheets of
paper or 40 envelopes.
To load paper in the Optional Tray 2, proceed as follows.
1 Pull the tray completely
out of the printer.
Notes: To load the envelope into the
tray, lift the lever on the left
side of the tray.
2 Press down on the bottom plate
to lock it into position.
F.18 P RINTER O PTION
Optional Tray 2
3 Squeeze and lift the length
guide and slide it to the desired
paper size until it clicks into
place.
4 Lift the width guide on the paper
guide to the desired paper size
until it clicks into place.
The paper size is indicated on the
bottom of the Optional Tray 2.
5 Squeeze the width guide and slide
it to the right side of the Tray.
6 Place the paper against the left
of the rear paper guide.
P RINTER O PTION
F.19
Optional Tray 2
Notes:
●
●
Do not fold or crease the paper.
This mark indicates the height of
paper loaded.
7 Squeeze the width guide and
slide it to the right and left until
it touches the edge
of the paper.
Notes: The printer may pull paper from tray 1 first.
To change this, see ‘Paper Source Selection’ on page F.22.
F.20 P RINTER O PTION
Optional Tray 2
Loading the envelopes into the Optional Tray 2
1 Lift the lever
on the left
side of the
Tray.
3 Lift the width guide and
slide it to the envelope
size indicated
on the bottom.
4 Lift the length guide and
slide it to the envelope
size indicated
on the
bottom.
2 Press down on
the bottom plate
to lock it into
position.
5 Place the envelopes
against the left side of
the Tray. Squeeze the
envelope guide lever
and slide it to the left
until it touches the edge
of the envelopes.
6 Squeeze the width
guide and slide it
to the right and
left until it touches
the edge of the
envelopes.
P RINTER O PTION
F.21
Optional Tray 2
Paper Source Selection
Use PCL driver to select the tray you wish to print.
1 Select Start ➔ Settings ➔ Printers from the windows task bar.
2 Click on the Samsung ML-7300 PCL 6 icon.
3 Select Files ➔ Properties.
4 Click on the Paper tab.
5 Set the source item to Default Value or Optional Tray 2.
Click
Notes: Settings in the printer driver and software application override
operator panel settings.
F.22 P RINTER O PTION
Optional Tray 2
You can select a paper source by setting the TRAY item using the control
panel menu.
If you do not use printer driver. To Select Optional Tray 2 as the default setting:
1 Press On Line.
Result: The OFFLINE message appears on
the display and the printer is off-line.
2 Press the Menu > or < buttons one
or more times until ‘Printing Menu’ is
displayed.
3 Press the Item < or > buttons one or
more times until ‘Tray’ appears on the
display.
4 Press the Value + or - buttons one or more
times to select ‘OPT’.
5 Press the Enter button.
●
An asterisk(❊) appears beside the
current user default setting for that
menu item.
P RINTER O PTION
F.23
Appendix
G
Using your
Printer in Linux
You can use Samsung ML-7300 Series printer in Linux
environment.
This appendix provides information on the following topic:
• Linux Driver Installation
Linux Driver Installation
This Linux driver is designed for Samsung ML-7300 Series
printer and supports Linux Red Hat 6.0 or higher and Intel
Linux. If your Linux version is not included, this driver might
not work properly.
• Install Setup Script file configuration
a. /cdrom/linux/install.sh
b. /cdrom/linux/ssprt.db
c. /cdrom/linux/readme.txt
Installation
To install the driver, open the x terminal screen and take the
following steps:
1. Mount the CD-ROM
drive.
Notes: To mount the CD-ROM drive, you must be a super
user or must be authorized to mount the CD-ROM by the
super user. If you fail to mount the CD-ROM drive, ask the
system administrator.
To mount the CD-ROM drive:
1 Insert the Samsung ML-7300 Series CD-ROM into the
CD-ROM drive.
2 Mount the CD-ROM drive under a directory like /mnt in
order to access the files on the CD-ROM:
>mount -t iso9660 /dev/cdrom /mnt/cdrom
2. Install setup script.
For details on installing the setup script, refer to the
/cdrom/linux/readme.txt file.
Add the driver to the printer list by typing in:
/cdrom/linux>install.sh (or)
/cdrom/linux>./install.sh (if the path of the current
working directory is not determined).
U SING Y OUR P RINTER
IN
L INUX
G.1
Linux Driver Installation
3. Set up the printer filter.
To set up:
1 Run printtool at x terminal.
2 To add the printer driver, click the Add button.
3 In the Add a Printer Entry window, decide the printer
type you will use. Select Local Printer if you have a PCconnected printer.
4 Click the OK button.
5 If the Info button appears, ignore it, then click the OK
button.
6 The Edit xxxx Entry window opens (where xxxx is the
printer type you have selected at step 3).
If you are not an advanced user, do not change the
Names/Spool Directory/File Limit in Kb/Printer
Device option.
7 Click the Select button in the Input Filter to access
filter setup.
8 Select Samsung Printer PCL 5e Compatible for the
Printer Type item. Then select the default resolution and
paper size.
9 To save the setting, press the OK button.
10 In the Edit xxxx Entry window, press the OK button to
complete the printer driver installation.
11 You can find that the printer driver is added to the
driver window. Select Quit from the PrintTool menu.
G.2 U SING Y OUR P RINTER
IN
L INUX
Memo
U SING Y OUR P RINTER
IN
L INUX
G.3
INDEX
Numeric
D
16MB RAM . . . . . . . . . . . . . .1.2
21PPM . . . . . . . . . . . . . . . . .1.2
500-Sheet Tray . . . . . . . . . . .1.3
DEMOPAGE . . . . . . . . . . . . .3.15
DENSITY . . . . . . . . . . . . . . .3.12
Duplex . . . . . . . . . . . . .5.7, 5.13
Duplex JAM . . . . . . . . . . . . . .7.5
A
E
Adhesive tape . . . . . . . . . . . .2.2
AUTO CR . . . . . . . . . . . . . . .3.8
AUTOCONT . . . . . . . . . . . . . .3.9
envelopes, print . . . . . . . . . .4.5
error messages . . . . . . . . . . .7.5
Ethernet 10/100 Base T . . . . .F.11
B
F
BAUDRATE
. . . . . . . . . . . . .3.17
Folio . . . . . . . . . . . . . . . . . .2.7
Font Navigator . . . . . . . . . . .2.16
Front view . . . . . . . . . . . . . .1.3
C
CD . . . . . . . . . . . . . . . . . . .2.12
CONFIG MENU . . . . . . . . . . . .3.9
EMUL
PWR SAVE
AUTOCONT
ECONO
JAM RECV
TONERLOW
SWITCH
LOCKTRAY
Copies . . . . . . . . . . . . . . . . .5.3
COURIER . . . . . . . . . . . . . .3.16
COVER OPEN . . . . . . . . . . . . .7.5
I
I NDEX
G
graphic mode . . . . . . . . . . . .5.5
graphic tab . . . . . . . . . . . . . .5.4
H
halftone, setting . . . . . . . . . .5.5
hardware requirements . . . . .2.13
INDEX
I
N
infrared adapter . . . . . . . . . .F.15
I/O MENU . . . . . . . . . . . . . .3.17
network interface
install network card . . . . . . .F.8
set up a locally shared printerD.1
network menu . . . . . . . . .3.18
network problem . . . . . . . .7.10
J
JOB MENU
. . . . . . . . . . . . .3.12
L
Label, printing . . . . . . . . . . . .4.7
Landscape . . . . . . . . . . . . . .5.3
Linux . . . . . . . . . . . . . . . . .G.1
LocalTalk . . . . . . . . . . . . . . .F.12
LSU cleaner . . . . . . . . . . . . .6.6
O
option
closing cover . . . . . . . . . . .F.3
memory SIMM . . . . . . . . . .F.5
nwtwork option card . . . . . .F.8
Optional Tray 2 . . . . . . . . .F.17
preparations . . . . . . . . . . . .F.2
serial/IrDA . . . . . . . . . . . .F.15
serial/LocalTalk . . . . . . . . .F.14
orientation . . . . . . . . . . . .5.3
overlay tab . . . . . . . . . . . . . .5.9
M
Macintosh . . . . . . . . . . . . . .B.1
Macintosh Problems . . . . . . .7.11
manual feed
loading paper . . . . . . . . . . .4.3
paper source setting . . . . . .5.3
memory, option . . . . . . . . . . .F.5
menu botton . . . . . . . . . . . . .3.2
MP size . . . . . . . . . . . . . . . .3.5
multiple images . . . . . . . . . . .5.7
multi-purpose tray
loading paper . . . . . . . . . . .4.1
paper soruce setting . . . . . .5.3
P
paper
acceptable size and capacities A.4
guidelines . . . . . . . . . . . . .A.5
specifications . . . . . . . . . . .A.4
supported type . . . . . . . . . .A.5
paper orientation, setting . . . .5.3
paper source, setting . . . . . . .5.3
paper tray
change paper size in tray . . .5.3
load paper . . . . . . . . . . . . .2.5
optional tray 2 . . . . . . . . .F.17
I NDEX
II
INDEX
P
(continued)
paper type, setting . . . . . . . .5.3
parallel, connection . . . . . . . .2.8
PCL 6, Properties
graphic tab . . . . . . . . . . . .5.4
output tab . . . . . . . . . . . . .5.6
overlay tab . . . . . . . . . . . .5.9
paper tab . . . . . . . . . . . . .5.2
printer tab . . . . . . . . . . . .5.8
watermark tab . . . . . . . . .5.11
postscript emulation . . . . . . . .C.2
install PPD file for Macintosh .B.1
power saver . . . . . . . . . . . . .3.9
power switch . . . . . . . . . . . .2.10
print quality problem, solving . .7.9
printer control board . . . . . . . .F.4
printer driver . . . . . . . . . . .2.12
pcl 6
postscript . . . . . . . . . . . . .C.1
font navigator . . . . . . . . .2.16
linux driver . . . . . . . . . . . .G.1
printer memory connector . . . .F.4
printer menu . . . . . . . . . . . .3.4
printer tab . . . . . . . . . . . . . .5.8
printing menu . . . . . . . . . . . .3.5
printing problem . . . . . . . . . .7.8
PS3 menu . . . . . . . . . . . . . .3.17
Q
quality, problems . . . . . . . . . .7.9
III I NDEX
R
rear paper guide . . . . . . . . . .2.5
rear right guide . . . . . . . . . . .2.6
rear view . . . . . . . . . . . . . . .1.3
REDAY status message . . . . . .3.3
resolution . . . . . . . . . . . . . . .5.5
ROM SIMM connector . . . . . . .F.4
S
SELFTEST . . . . . . . . . . . . . .2.11
Serial/LocalTalk connector . . . .F.4
Serial/LocalTalk option card . .F.12
setting up . . . . . . . . . . . . . .2.12
software requirements . . . . .2.13
specifications
paper . . . . . . . . . . . . . . . .A.4
controller . . . . . . . . . . . . .A.1
enginge . . . . . . . . . . . . . .A.2
paper handling . . . . . . . . . .A.3
environment . . . . . . . . . . .A.3
package weight . . . . . . . . .A.3
SRT mode . . . . . . . . . . . . . .5.5
INDEX
T
V
test menu . . . . . . . . . . . . . .3.15
testing the printer . . . . . . . .2.11
toner cartridge
distributing . . . . . . . . . . . .6.1
install . . . . . . . . . . . . . . . .2.3
life expectancy . . . . . . . . . .6.1
recycle . . . . . . . . . . . . . . .6.1
redistribute toner . . . . . . . .6.2
save toner . . . . . . . . . . . . .5.5
storage . . . . . . . . . . . . . . .6.1
top cover . . . . . . . . . . . . . . .1.3
top output bin . . . . . . . . . . . .1.3
transparencies . . . . . . . . . . .4.8
value button . . . . . . . . . . . . .3.1
W
watermark tab . . . . . . . . . . .5.11
width guide . . . . . . . . . . . . .2.5
U
uninstall utility . . . . . . . . . .2.15
unpacking your printer . . . . . .2.1
I NDEX
IV