Moffat MSF 615 Specifications

ELECTRIC OVEN
MSF 615
INSTRUCTION BOOKLET
Please read this instruction booklet before using the appliance
Keep this instruction book for future
reference and ensure it is passed on to any
new owner.
5
4
3
2
1
6
7
8
9
10
1.
2.
3.
4.
5.
Control Panel
Thermostat Control Knob
Oven Function Control Knob
Thermostat Control Light
Electronic Programmer
6. Grill
7. Oven light
8. Oven fan
9. Rating plate
10. Oven door
GB
Important Safety Information
You MUST read these warnings carefully before installing or using the oven. If you need
assistance, contact our Customer Care Department on 08705 950950
Installation
• This oven must be installed by qualified
personnel to the relevant British Standards.
• This oven is heavy. Take care when moving it.
• Remove all packaging, both inside and outside
the oven, before using the oven.
• Do not attempt to modify the oven in any way.
Child Safety
• This oven is designed to be operated by
adults. Do not allow children to play near or with
the oven.
• The oven gets hot when it is in use. Children
should be kept away until it has cooled.
During Use
• This oven is intended for domestic cooking
only. It is not designed for commercial or industrial
purposes.
• Never line any part of the oven with aluminium
foil.
• Do not allow heatproof cooking material, e.g.
roasting bags, to come into contact with oven
elements.
• Never place plastic or any other material which
may melt in or on the oven.
• Do not place sealed cans or aerosols inside
the oven. They may explode if they are heated.
• Do not hang towels, dishcloths or clothes
from the oven or its handle.
• Do not use this oven if it is in contact with water
and never operate it with wet hands.
• Take great care when heating fats and oils as
they will ignite if they become too hot.
• Always use oven gloves to remove and replace
food in the oven.
• Ensure that all control knobs are in the OFF
position when not in use.
• Do not leave cookware containing foodstuffs,
e.g. fat or oil in or on the oven in case it is
inadvertently switched ON.
• When using other electrical appliances, ensure
the cable does not come into contact with the
hot surfaces of the oven.
Maintenance and Cleaning
• Only clean this oven in accordance with the
instructions.
• The oven should be kept clean at all times. A
build-up of fats or other foodstuffs could result in
a fire, especially in the grill pan.
• Always allow the oven to cool down and
switch off the electrical supply before carrying
out any cleaning or maintenance work.
Service
• This oven should only be repaired or serviced
by an authorised Service Engineer and only
genuine approved spare parts should be used.
Environmental Information
• After installation, please dispose of the
packaging with due regard to safety and the
environment.
• When disposing of an old appliance, make it
unusable, by cutting off the cable. Remove any
door catches, to prevent small children being
trapped inside.
Guide to Use the instructions
The following symbols will be found in the
text to guide you throughout the Instructions:
Safety Instructions
Step by step instructions for an
operation
Hints and Tips
Environmental information
Controls
Oven Function Control Knob
Oven Light - The oven light will be on
without any cooking function.
Defrost Setting - This setting is intended
to assist in thawing of frozen food.
Fan Oven cooking - This allows you to
roast or roast and bake simoultaneously
using any shelf, without flavour
transference.
Grill - The heat comes from the top
element only
FO 2593
50
max
100
Thermostat Control Knob
150
Turn the thermostat control knob clockwise to
select temperatures between 50°C and 250°C
(MAX).
Thermostat Control Light
The thermostat control light will come on when
the thermostat control knob is turned. The light
will remain on until the correct temperature is
reached. It will then cycle on and off to show
the temperature is being maintained.
The Safety Thermostat
This oven is provided with a safety thermostat.
In case of malfunctioning of the main
thermostat, and consequent over-heating, the
safety device will stop the power supply to the
appliance. If this happens, call your local
Service Force Centre. Under no
circumstances should you attempt to repair the
appliance yourself.
200
FO 2595
Before the First Use
Remove all packaging, both inside
and outside the oven, before using the
appliance.
Before first use, the oven should be heated
without food. During this time, an unpleasant
odour may be emitted. This is quite normal.
1. Set the time of day with the electronic
programmer (see relevant instructions).
2. Switch the oven function control knob
to fan cooking
.
3. Set the thermostat control knob to
MAX.
4. Open a window for ventilation.
5. Allow the oven to run empty for
approximately 45 minutes.
This procedure should be repeated with the grill
function for approximately 5-10 minutes.
Electronic programmer
4
1. Push button for selecting
a function
5
6
7
8
2. Decreasing control button “
3. Increasing control button “ ”
4. Display
5. “Cooking Duration” pilot lamp
6. “End of cooking” pilot lamp
7. “Minute minder” pilot lamp
2
1
3
The oven will work only if the time
of day has been set. Moreover, the
oven can also be operated without any
programme.
Setting the time of day
When the power supply is switched on, or after
a power failure, the “Time of day” pilot lamp
will flash on the display.
To set the correct time of day:
1. press button “ ” or “ ”.
2. After the setting is carried out, wait for 5
seconds: the “Time of day” pilot lamp
will go out and the display will show the
set time. The appliance is ready for use.
To reset the correct time of day:
1. press button
repeatedly to select the
“Time of day” function. The relevant pilot
lamp will start flashing. Then proceed as
described above.
The time of day can only be reset if no
or
automatic function (cook duration
end of cooking
) has been set.
“Cooking Duration”
function
This function allows the oven to automatically
switch off at the end of a programmed cooking
duration time. Place food in the oven, select a
cooking function and adjust the cooking temperature.
8. “Time of day” pilot lamp
”
Press button
repeatedly to select the
“Cooking Duration” function. The relevant
will start flashing. Then, proceed
pilot lamp
as follows:
To set the duration time:
1. press button “ ” or “ ”.
2. After the setting is carried out, wait for 5
seconds: the "Cooking Duration" pilot lamp
will come on and the display will revert
to the time of day.
3. When cooking time is over, the oven will
be switched off automatically and an
acoustic alarm will be heard, while the pilot
lamp will start flashing. Turn the oven
function and the thermostat control knob
to zero.
To switch off the acoustic alarm, press any
button. NOTE: when doing this operation,
the oven will be operated again, therefore,
remember to turn the oven function and
the thermostat control knob to zero at the
end of the cooking time.
To cancel the duration time:
repeatedly to select the
1. Press button
“Cooking Duration” function. The relevant
will flash and the display will
pilot lamp
show the remaining cooking time.
2. Press button “ ” until the display shows
“0:00”. After 5 seconds the pilot lamp will
go out and the display will revert to the time
of day.
“End of cooking” function
Thanks to this function, you can set the oven to
switch off automatically when a programmed
end of cooking time is over. Place food in the
oven, select a cooking function and adjust the
cooking temperature. Press button
repeatedly to select the “End of cooking”
function. The relevant pilot lamp
will start
flashing. Then, proceed as follows:
To set the End of cooking time:
1. press button “ ” or “ ”.
2. After the setting is carried out, wait for 5
seconds: the “End of cooking” pilot lamp
will come on and the display will revert
to the time of day.
3. When cooking time is over, the oven will
be switched off automatically and an
acoustic alarm will be heard, while the pilot
lamp will start flashing. Turn the oven
function and the thermostat control knob
to zero.
To switch off the acoustic alarm, press any
button. NOTE: when doing this operation,
the oven will be operated again, therefore,
remember to turn the oven function and
the thermostat control knob to zero when
cooking is over.
To cancel the End of cooking time:
1. Press button
repeatedly to select the
“End of cooking” function. The relevant
will flash and the display will
pilot lamp
show the programmed End of cooking
time.
2. Press button “ ” until the display shows
the current time of day. The programmer
will beep and the pilot lamp will go out.
“Cooking duration”
and
“End of cooking time”
combined
The functions “Cooking duration” and “End of
cooking time” can be used simultaneously to
set the oven to switch on and off automatically
at a later time.
1. With the “Cooking duration” function
(carry out the cooking duration setting as
described in the relevant chapter) set the
duration time. Then, press button : the
display will show the programmed setting.
2. With the “End of cooking time” function
(carry out the End of cooking setting as
described in the relevant chapter) set the
end of cooking time.
The relevant pilot lamps will come on and
the display will show the time of day. The
oven will switch on and off according to
the set programmes.
“Minute minder” function
The minute minder alarm will sound at the end
of a timed period, but THE OVEN WILL
REMAIN ON, if it is in use.
To set the minute minder:
1. Press button
repeatedly to select the
“Minute minder” function. The relevant pilot
lamp will start flashing.
2. Then, press button “ ” or “ ” (maximum:
2 hours, 30 minutes).
3. After the setting is carried out, wait for 5
seconds: the “Minute minder” pilot lamp
will come on.
4. At the end of the timed period, the pilot
lamp will start flashing and acoustic alarm
will be heard. To switch off the acoustic
alarm, press any button.
To cancel the minute minder:
1. Press button
repeatedly to select the
“Minute minder” function. The relevant pilot
lamp will flash and the display will show
the remaining time.
2. Press button “ ” until the display shows
“0:00”. After 5 seconds the pilot lamp will
go out and the display will revert to the time
of day.
How to switch off the display
1. Press two or three programmer push
buttons simoultaneously and keep them
pressed for about 5 seconds. The display
will switch off.
2. To switch on the display, press any button.
The display can be switched off only if
no other functions have been set.
Using the Oven
Always cook with the oven door
closed.
Stand clear when opening the drop
down oven door. Do not allow it to fall open support the door using the door handle, until
it is fully open.
The oven has four shelf levels, and is
supplied with two shelves. The shelf
positions are counted from the bottom of the
oven as shown in the diagram.
Do not place cookware directly on the oven
base.
Cleaning the Oven
Before cleaning always allow the
cooling fan to cool the cooker down
before switching off at the electricity supply.
Do not use steam cleaners.
The oven should be kept clean at all times. A buildup of fats or other foodstuffs could result in a fire,
especially in the grill pan.
Before using any cleaning materials on your oven,
check that they are suitable and that their use is
recommended by the manufacturer.
Cleaners that contain bleach and harsh abrasives
should NOT be used.
For external and internal cleaning, use a soft cloth
well wrung out in warm water to which a little liquid
detergent has been added.
To prevent damaging or weakening the door glass
panels avoid the use of the following: household
detergent and bleaches, impregnated pads
unsuitable for non-stick saucepans, "Brillo/Ajax"
pads or steel wool pads, chemical oven pads or
aerosols, rust removers, bath/sink stain removers.
Should the inner door glass become heavily soiled
it is recommended that a cleaning product such
as Hob Brite is used.
DO NOT clean the oven door while the glass
panels are warm. If this precaution is not
observed the glass panel may shatter.
If the door glass panel becomes chipped
or has deep scratches, it must be replaced to
prevent the possibility of the panel shattering.
Contact your local Service Force Centre.
4
3
2
1
Cooking Chart
The oven temperatures are intended as a guide only. It may be necessary to increase or
decrease the temperatures by 10 °C to suit
individual preferences and requirements.
NOTE: Shelf positions are counted from
bottom of the oven.
Food
Cooking
Shelf
Temp (°C) Position
Biscuits
Bread
Casseroles
Cakes:
- Small and queen
- Sponges
- Madeira
- Rich Fruit
- Christmas
- Meringues
Fish
Fruit Pies and Crumbles
Milk Puddings
Pastry:
- Choux
- Shortcrust
- Flaky
- Puff
Plate Tarts
Quiches/Flans
Scones
Roasting:
- Meat & Poultry
}
180-190
210-220
130-140
160-170
160-170
140-150
130-140
130-140
90-100
170-190
190-200
130-140
190-200
180
170-180
210-220
160-280
Shelf
positions
are not
critical
but
ensure
that oven
shelves
are
evenly
spaced
when
more
than one
is used.
Replacing The Oven Light
Grilling Chart
Cooking time depends on the thickness of
the meat and not on its weight.
Grilling must be carried out with
the oven door closed. The grill pan
handle must be removed from the pan.
Type of food
Mins per side
Bacon rashers
Chicken joints
Gammon rashers
Lamb chops
Pork chops
Sausages (turning as required)
Steaks (average thickness)
Rare
Medium
Well done
Toast
2-5
15 - 20
5-8
6 - 12
10 - 15
10 - 12
3-6
6 - 10
8 - 12
1 - 11/2
Disconnect the appliance
If the oven bulb needs replacing, it must comply
with the following specifications:
Electric power: 15W; Electric rate: 230-240V
(50 Hz); Resistant to temperatures of 300°C;
Connection type: E14.
These bulbs are available from your local
Service Force Centre. To replace the faulty
bulb:
1. Ensure the oven is isolated from the
electrical supply.
2. Turn the glass cover counterclockwise.
3. Remove the faulty bulb and replace with
the new one.
4. Refit the glass cover and restore the
electrical supply.
Something not working
If the appliance is not working correctly, please carry out the following checks, before contacting
your local Service Force Centre.
IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by
incorrect use or installation, a charge will be made even if the appliance is under guarantee.
SYMPTOM
The oven does not come on
SOLUTION
Check that both a cooking function and
temperature have been selected.
Check the appliance is wired in properly,
and the socket switch or the switch from the
mains supply to the oven are ON.
Check that the time of day has been set with
the electronic programmer.
The oven temperature light does not
come on
Select a temperature with the thermostat
control knob
Select a function with the oven function
control knob.
Select a function with the oven function
control knob
Check the light bulb, and replace it if
necessary (see above)
The oven light does not come on
It takes too much time to finish the dishes,
or they are cooked too fast.
The temperature may need adjusting
Refer to the contents of this booklet,
especially to the chapter “Using the Oven”.
Steam and condensation settle on the
food and the oven cavity.
Leave dishes inside the oven no longer than
15-20 minutes after the cooking is completed.
Service and Spare Parts
If you require spare parts or an engineer
contact your local Service Force Centre by
telephoning:
08705 929 929
Your call will be routed to the Service Centre
covering your post code area. The addresses
of Service Force Centres are detailed on the
following pages.
CUSTOMER CARE
For general enquiries concerning your Moffat
appliance and for further information on Moffat
products, contact our Customer Care
Department by letter or telephone as follows:
Customer Care Department
Moffat
55-77 High Street
Slough
Berkshire SL1 1DZ
Tel : 08705 950950
* calls to this number may be recorded for training purposes
Guarantee Conditions
We, Moffat, undertake that if, within 12 months
of the date of the purchase, this Moffat appliance
or any part thereof is proved to be defective by
any reason only of faulty workmanship or
materials, we will, at our option, repair or replace
the same FREE OF ANY CHARGE for labour,
materials or carriage on condition that:
* The appliance has been correctly installed
and used only on the gas and electricity supply
stated on the rating plate.
* The appliance has been used for normal
domestic purposes only, and in accordance
with the manufacturer's instructions.
* The appliance has not been serviced,
maintained, repaired, taken apart or tampered
with by any person not authorised by us.
* All service work under this guarantee must be
undertaken by a Moffat Service Force Centre.
* Any appliance or defective part replaced shall
become the Company's property.
* This guarantee is in addition to your statutory
and other legal rights.
Home visits are made between 8.30am and
5.30pm Monday to Friday. Visits may be
available outside these hours, in which case a
premium will be charged.
Exclusions
This guarantee does not cover:
* Damage or calls resulting from transportation,
improper use or neglect, the replacement of
any light bulbs or removable parts of glass or
plastic.
* Costs incurred for calls to put right an
appliance which is improperly installed or calls
to appliance outside the United Kingdom.
* Appliances found to be in use within a
commercial or similar environment, plus those
which are the subject to rental agreements.
* Products of Moffat manufacture which are not
marketed by Moffat.
European Guarantee
If you should move to another country within
Europe then your guarantee moves with you to
your new home subject to the following
qualifications:
* The guarantee starts from the date you first
purchased your product.
* The guarantee is for the same period and to
the same extent for labour and parts as exist in
the new contry of use for this brand or range of
products.
* This guarantee relates to you and cannot be
transferred to another user.
* Your new home is within the European
Community (EC) or European Free Trade
Area.
* The product is installed and used in
accordance with our instructions and is only
used domestically, i.e. a normal household
The electrical supply complies with the
specification given in the rating label.
* The product is installed taking into account
regulations in your new country.
Before you move, please contact your nearest
Customer Care centre, listed below, to give
them details of your new home. They will then
ensure that the local Service Organisation is
aware of your move and able to look after you
and your appliances.
France Senlis
+33 (0) 3 44 62 20 13
Germany Nürnberg +49 (0) 800 234 7378
Italy
Pordenone +39 (0) 800117511
Sweden Stockholm +46 (0) 20 78 77 50
UK
Slough
+44 (0) 1753 219898
Technical Data
Electrical Connection
Heating element ratings
The oven is designed to be connected to 230240V (50Hz) electricity supply.
The oven has an easily accessible terminal
block which is marked as follows:
Letter L
Live terminal
Letter N
Neutral terminal
or E
Earth terminal
Fan cooking element
Grill element
Oven Fan
Oven Light
Cooling Fan
Total Rating
2,080
1,830
25
15
20
2,150
W
W
W
W
W
W
THIS OVEN MUST BE EARTHED
Dimensions of the oven cavity
Height
Width
Depth
Oven capacity:
325 mm.
440 mm.
400 mm.
55 litres
Moffat
MSF 615
A
0,79 kW/h
0,78 kW/h
53,0
43 min.
41 min.
1130 cm2
The cable used to connect the oven to
the electrical supply must comply to the
specifications given below.
It is necessary that you install a double pole
Connection
via
Min. size Cable / flex Fuse
Cable/flex type
13 A socket
outlet
2.5 mm2
3 core
butyl
insulated
2.5 mm2
PVC/PVC
twin and
earth
13 A spur box
This appliance
complies with the
following E.E.C.
Directives:
• 73/23 - 90/683
(Low Voltage
Directives)
• 93/68 (General
Directive);
• 89/336
(Electromagnetical
Compatibility
Directive)
and subsequent
modifications.
Cooker
Control
Circuit
13 A
min.
13 A
switch between the oven and the electricity
supply (mains), with a minimum gap of 3mm
between the switch contacts and of a type
suitable for the required load in compliance
with the current rules.
The switch must not break the yellow and
green earth cable at any point.
Important
After installation and connecting, the cable
must be placed so that it cannot at any point
reach a temperature of more than 60°C above
the ambient temperature.
Before the oven is connected, check that the
main fuse and the domestic installation can
support the load and that the power supply is
properly earthed.
The manufacturer declines any
responsibility should these safety
measures not be carried out.
Building In
Please ensure that when the oven is
installed it is easily accessible for the
engineer in the event of a breakdown.
The surround or cabinet into which the oven
will be built must comply with these
specifications:
the dimensions must be as shown in the
relevant diagrams;
the materials must withstand a temperature increase of at least 60°C the above
temperature;
proper arrangements must be made for a
continuous supply of air to the oven to
prevent the oven overheating.
Securing The Oven
To The Cabinet
1. Fit the oven into the cabinet recess,
2. Open the oven door
3. Secure the oven to the kitchen cabinet with
four wood screws, which fit the holes
provided in the oven frame.
356xx-xxx stripped
Grafiche MDM - Forlì
Dimensions of the oven and recess required
are given in the relevant diagrams.
10/03