s
Spare parts list for Candy model
Supplier model number:HJA26017119
550m3/H
For whole cooker hood
B20-2201-004-P
1
B20-2201-006-P
2
3
B71-4301-007-B
4
B76-4301-001-B
B35-2201-038-0
5
B35-2501-014-0
6
B76-4308-004-B
7
B30-2201-079-0
8
B65-2201-081-0
9
B62-2201-087-0
10
B64-2501-108-0
11
B30-2201-078-0
12
B23-2201-012-P
13
B23-2201-010-P
14
B23-2201-008-P
15
B62-2301-070-0
16
B30-2502-015-0
17
18
19
20
21
22
23
24
25
26
27
For motor accessory :
120mm outlet adaptor
1
1
1
1
3
2
1
1
2
2
1
1
1
1
1
1
1
USD
USD
USD
USD
USD
USD
USD
USD
USD
USD
USD
USD
USD
USD
USD
USD
USD
3.5
3.5
23.09
3.00
2.10
1.1
18.25
0.45
0.2
0.75
2.00
0.45
1.00
0.25
0.25
0.85
0.6
For motor accessory(B76-4308-004-B)
1
B30-2201-068-0
2
B30-2301-013-0
3
B61-2301-015-0
4
B30-2301-014-0
5
B30-2201-022-0
6 B30-2301-012-0
For Mechanical switch
Upper Chimney (400MM height)
Lower Chimney (400MM height)
Hood body Assembly (S.S.)
Mechanical Push button set
Alumnium fitler (9×259.5×230.5)
Carbon filter
550m3/h motor accessories
Junction box base
Lamp conneter
Normal Light (NB01)
3µF capacitor
Junction box cover
Hanging Board
Lower chimney bracket
Upper chimney bracket
Cable (without plug)
1
USD
1
USD
Motor 550m3/h
1
USD
Impeller
1
USD
2
USD
1
USD
1
USD
1
USD
1
USD
Motor wiring holder
Plastic motor housing (Right)
Non-return valve
Plastic motor housing (Left)
0.2
1.55
13
1.6
0.35
1.55
For Mechanical switch(B76-4301-001-B)
1
B30-2201-090-0
Switch box cover
2
B60-2201-092-0
Push button switch
3
B30-2201-089-0
Switch box bottom
B62-2301-048-0 Switch wiring (950mm)
4
5
6
1
USD
Order per set, See above price
Baumatic
Spare parts list for Baumatic model F60.2SS-AR
Position Prefix
1
2
3
4
5
6
7
7-1
7-2
7-3
7-4
8
9
10
11
12
13
14
15
16
17
XAA
XAA
XAA
XAA
XAA
X
XAA
XAA
XAA
XAA
XAA
XAA
XAA
XAA
XAA
XAA
XAA
XAA
XAA
XAA
XAA
Supplier
Item code
MODEL
NUMBER
Description UK
B20-2201-004-P
B20-2201-006-P
B71-4301-001-B
B76-4201-002-B
B35-2201-038-0
ST2
B76-4308-004-B
B30-2301-013-0
B30-2301-012-0
B30-2301-014-0
B30-2201-022-0
B30-2201-079-0
B65-2201-081-0
B62-2201-087-0
B64-2501-108-0
B30-2201-078-0
B23-2201-012-P
B23-2201-010-P
B23-2201-008-P
B62-2301-070-0
B30-2502-015-0
F60.2SS-AR
F60.2SS-AR
F60.2SS-AR
F60.2SS-AR
F60.2SS-AR
F60.2SS-AR
F60.2SS-AR
F60.2SS-AR
F60.2SS-AR
F60.2SS-AR
F60.2SS-AR
F60.2SS-AR
F60.2SS-AR
F60.2SS-AR
F60.2SS-AR
F60.2SS-AR
F60.2SS-AR
F60.2SS-AR
F60.2SS-AR
F60.2SS-AR
F60.2SS-AR
Upper Chimney (400MM height)
Lower Chimney (400MM height)
Hood body Assembly (S.S.)
Mechanical Push button set
Alumnium filter (9×259.5×230.5)
Carbon filter (Pair)
550m3/h motor accessories
Plastic motor housing (Right)
Plastic motor housing (Left)
Impeller
Non-return valve
Junction box base
Lamp connecter
Normal Light (NB01)
3μF capacitor
Junction box cover
Hanging Board
Lower chimney bracket
Upper chimney bracket
Cable (without plug)
120mm outlet adaptor
Currency Price
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
3.50
3.50
13.60
3.00
2.10
18.25
1.55
1.55
1.60
0.35
0.45
0.20
0.75
2.00
0.45
1.00
0.25
0.25
0.85
0.60
F60.2-BL/SS
F70.2-BL/SS
F90.2-BL/SS
Cooker hood
User Manual for your Baumatic
F60.2-BL/SS 60 cm cooker hood
F70.2-BL/SS 70 cm cooker hood
F90.2-BL/SS 90 cm cooker hood
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference; for
you or any person not familiar with the operation of the appliance.
JW 08/08/13
2
Contents Page
Environmental note
4
IMPORTANT SAFETY INFORMATION
5–7
Specifications of your cooker hood
F60.2-BL/SS
F70.2-BL/SS
F90.2-BL/SS
Optional extras (all models)
8 – 11
8
9
10
11
Using your Baumatic cooker hood
Before first use
To use your cooker hood
11 - 12
11
11-12
Cleaning your Baumatic cooker hood
The grease filters
12 - 13
13
Maintenance
Removing and cleaning the grease filters
Changing a light bulb
Fitting the carbon filters
13 - 15
13
14
15
Installation
Electrical connection
Before beginning installation
Installing your cooker hood
Connecting to external ducting
Fitting the chimney
Completing the installation
16 - 24
16-17
17-18
18-20
21
21-23
24
Extraction mode or recirculation mode?
24
Troubleshooting
25 - 26
Contact details
27
3
ENVIRONMENTAL NOTE
Note: Before discarding an old appliance, switch off and
disconnect it from the power supply. Cut off and render any
plug useless. Cut the cable off directly behind the appliance to
prevent misuse. This should be undertaken by a competent
person.
CONFORMITY TO W.E.E.E. DIRECTIVE
4
IMPORTANT SAFETY INFORMATION
Your safety is of the utmost importance to Baumatic.
Please make sure that you read this instruction booklet
before attempting to install or use the appliance. If
you are unsure of any of the information contained in
this booklet, please contact the Baumatic Advice Line.
IMPORTANT: Any installation work must be
carried out by a qualified electrician or
competent person.
o The hood must be installed in accordance with the installation
instructions and all measurements followed.
o If the cooker hood is installed for use above a gas appliance then
the provision for ventilation must be in accordance with the Gas
Safety Codes of Practice BS.6172, BS.5440 & BS.6891 (Natural
Gas) and BS.5482 (LP Gas) 1994, the Gas Safety (Installation &
Use) Regulations, the Building Regulations issued by the
Department of the Environment, the Building Standards
(Scotland) (Consolidated) Regulations issued by the Scottish
Development Department.
o It is dangerous to alter the specifications or to modify this
product.
Do not tamper with it or attempt to modify the
appliance in any way.
o When installing the hood, ensure that the following
recommended distances are observed between the highest point
on the hob top (including the burners) and the bottom of the
cooker hood:
 Electric cookers:
 Gas cookers:
700 mm
700 mm
IMPORTANT: DO NOT SET YOUR COOKER HOOD LESS
THAN 700mm ABOVE YOUR COOKER.
o When installed between adjoining wall cabinets, the cabinets
must not overhang the hob.
5
o The edges of the cooker hood are sharp – be mindful of this as
you handle your appliance, especially during installation and
cleaning. DO NOT CLEAN IN BEHIND THE GREASE FILTERS!
o If the room where the cooker hood is to be used contains a fuel
burning appliance such as a central heating boiler then its flue
must be of the sealed or balanced flue type.
o If other types of flue or appliances are fitted, ensure that there is
an adequate supply of air in the room.
o When the hood is being used in its extractor function, ensure
that the ducting is fire retardant and that there are no bends
sharper than 90 degrees as this will reduce the efficiency of the
hood.
o Ensure the ducting for the extractor function has the same
diameter as the outlet hole all the way through.
o Keep young children from using, playing with or
tampering with the cooker hood. Older children
and infirm persons should be supervised if they are
using the cooker hood.
o Your cooker hood is for domestic use only.
o Please dispose of the packing material carefully – children are
especially vulnerable to it.
o Dirty oil is an even greater fire risk.
o Always put lids on pots and pans when cooking
on a gas cooker.
o The manufacturer refuses to accept any responsibility for
damages arising to the hood or it catching on fire, from a failure
to observe the fire safety advice contained in this instruction
booklet.
o Remember that when in extraction mode, your cooker hood is
removing air from your room. Ensure that proper ventilation
measures are being observed.
6
o Note: Your cooker hood is designed to remove cooking
odours from the room and not steam.
o Warning - Always ensure that the cooker
hood has been disconnected from the power
supply before carrying out any work on the
hood, including replacing light bulbs.
o Do not connect the ducting system of this appliance to any
existing ventilation system which is being used for any other
purpose.
o Do not install above a cooker with a high level grill.
o Never leave frying pans unattended during use as
overheated fats and oils might catch fire.
o The lights on this appliance should only be used during operation
of the cooker hood. They should not be left on permanently and
used as a lighting source.
o The cooker hood should not be exposed to a direct heat source
from the cooking device underneath it, i.e. a naked flame from a
gas burner or heat from electric hob zones without a pan on
them.
o Do not attempt to use the cooker hood if it is damaged in any
way. Never attempt to use it without the grease filters fitted or
if the filters are excessively greasy!
o Never flambé cook under this cooker hood.
THE MANUFACTURER DECLINES ALL
RESPONSIBILITY IN THE EVENT OF FAILURE TO
OBSERVE THE INSTRUCTIONS GIVEN HERE, FOR
INSTALLATION, MAINTENANCE AND SUITABLE
USE OF THE HOOD.
7
Specifications of your cooker hood
F60.2-BL/SS
PRODUCT
DIMENSIONS
Height: 638–1080mm*
Width: 600 mm
Depth: 500 mm
DIMENSIONS OF
CHIMNEY SECTION:
172 mm x 222 mm
Your stainless steel cooker hood is fitted with:
o
o
o
o
o
o
Integrated centrifugal motor
Push button control operation
3 Speeds
2 Washable metallic grease filters
2 lights
Extraction or recirculation
Extraction capacity:
550 m³/hr
Optional extra: Carbon filter
MODEL NUMBER CARBON FILTER REQUIRED
F60.2-BL/SS-AR
ST2
F60.2-BL/SS-AT
ST1
* If you are using the appliance in recirculation mode, then PLEASE
NOTE that some of the vent in the upper chimney section must be
exposed. You will have to take this into account when calculating the
minimum height of the cooker hood when installed.
8
F70.2-BL/SS
PRODUCT DIMENSIONS
Height: 638–1080mm*
Width: 700 mm
Depth: 500 mm
DIMENSIONS OF
CHIMNEY SECTION:
172 mm x 222 mm
Your stainless steel cooker hood is fitted with:
o
o
o
o
o
o
Integrated centrifugal motor
Push button control operation
3 Speeds
2 Washable metallic grease filters
2 lights
Extraction or recirculation
Extraction capacity:
550 m³/hr
Optional extra: Carbon filter
MODEL NUMBER CARBON FILTER REQUIRED
F70.2-BL/SS-AR
ST2
F70.2-BL/SS-AT
ST1
* If you are using the appliance in recirculation mode, then PLEASE
NOTE that some of the vent in the upper chimney section must be
exposed. You will have to take this into account when calculating the
minimum height of the cooker hood when installed.
9
F90.2-BL/SS
PRODUCT DIMENSIONS
Height: 638–1080mm*
Width: 900 mm
Depth: 500 mm
DIMENSIONS OF
CHIMNEY SECTION:
172 mm x 222 mm
Your stainless steel cooker hood is fitted with:
o
o
o
o
o
o
Integrated centrifugal motor
Push button control operation
3 Speeds
3 Washable metallic grease filters
2 lights
Extraction or recirculation
Extraction capacity:
550 m³/hr
Optional extra: Carbon filter
MODEL NUMBER CARBON FILTER REQUIRED
F90.2-BL/SS-AR
ST2
F90.2-BL/SS-AT
ST1
* If you are using the appliance in recirculation mode, then PLEASE
NOTE that some of the vent in the upper chimney section must be
exposed. You will have to take this into account when calculating the
minimum height of the cooker hood when installed.
10
Optional extras (all models)
DK5 1 Metre length Ducting Kit 125 mm Ø.
DK10 3 Metre length Ducting Kit 125 mm Ø with flat channelling
included.
o Available from the Baumatic Spares Department.
Using your Baumatic cooker hood
Before first use
IMPORTANT: THIS PROCESS MUST BE FOLLOWED BEFORE
THE COOKER HOOD IS USED FOR THE FIRST TIME.
o You should use a good quality stainless steel cleaner and polish
on ALL of the stainless steel areas of your cooker hood, before it
is used for the first time.
o This will help to leave a silicone water-resistant film to protect
the stainless steel surfaces.
To use your cooker hood
o A
= ON/OFF button
o B
= Speed selection buttons
= Low speed
= Medium speed
= High speed
o C
= Light on/off button
o Before operating the hood, make sure that it has been installed
by a suitably qualified person, as per the information contained
in Baumatic’s installation instructions.
11
o Find the control panel, which is located at the front right of the
canopy.
o There are several buttons on the control panel, which perform
separate functions.
IMPORTANT: IDEALLY YOU SHOULD SWITCH ON
YOUR HOOD TEN MINUTES BEFORE YOU START TO
COOK, OR AT THE VERY LEAST WHEN YOU BEGIN
COOKING. YOU SHOULD ALSO RUN YOUR HOOD FOR
TEN MINUTES AFTER YOU HAVE FINISHED COOKING.
Cleaning your Baumatic cooker hood
IMPORTANT:
BEFORE
CLEANING,
ALWAYS
ENSURE THAT YOU HAVE SWITCHED YOUR
COOKER HOOD OFF AT THE OMNI-POLAR
SWITCH, SET AT THE WALL FROM THE CABLE.
Cleaning
o Clean the external parts of your cooker hood with mild liquid
detergent and a new damp cloth.
o Never use abrasive powder, corrosive solvents or brushes.
o Never insert pointed objects into the motor’s protective grid.
o Only clean the control panel and grease filter grill with mild liquid
detergents and a new damp cloth.
o If you are using the appliance in recirculation mode, then be
sure to replace the carbon filters at the recommended intervals
(see section on “Fitting the carbon filter”). A build up of grease
could cause a fire hazard.
o Never attempt to clean the area above the grease filters.
12
The grease filters
o Your cooker hood is fitted with grease filters, which help to absorb
grease particles and protect your kitchen and furniture from greasy
residues.
o These metallic filters may become inflammable if you allow them to
get saturated with this greasy residue.
o To prevent this fire hazard, the filters should be cleaned regularly.
Depending on use, this should be done every 10-15 days or at least
once a month, using hot water and normal washing-up detergent.
o DO NOT WASH THE GREASE FILTERS IN A DISHWASHER.
Maintenance
Removing and cleaning the grease filters
o First remove the grease filters by pulling
down on the handle and pulling them away
from the cooker hood.
o Soak the grease filters in hot water and washing up liquid for about
an hour.
o Rinse them off thoroughly with hot water.
o Repeat the process if required.
o Refit the grease filters once they have dried.
o IMPORTANT: Let the grease filters dry
thoroughly before refitting them in the
cooker hood.
13
Changing a light bulb
IMPORTANT: BEFORE ATTEMPTING TO CHANGE
A LIGHT BULB, YOU MUST ENSURE THAT YOU
HAVE DISCONNECTED THE COOKER HOOD FROM
YOUR MAINS SUPPLY.
o Remove the grease filters (as described
on page 15).
o Prior to touching the light bulbs ensure they are cooled down.
o Find the bulb that requires replacement, you will find it located in
the light fixture which is inside the exposed section of the
canopy.
o Unscrew the light bulb that needs to be replaced and insert a
new E14 40W (max) bulb.
o IMPORTANT: Defective bulbs should be replaced immediately.
o If the lights still do not work, make sure that the lamps are fitted
properly into their housings before you call for technical
assistance.
o Refit the grease filters.
14
Fitting the carbon filters
If the appliance is being used to be used in recirculation mode then it
is necessary to fit carbon filters. This will help to absorb unpleasant
odours caused by cooking.
IMPORTANT: BEFORE ATTEMPTING TO FIT OR
REMOVE THE CARBON FILTERS, YOU MUST
ENSURE THAT YOU HAVE DISCONNECTED THE
RANGEHOOD FROM YOUR MAINS SUPPLY.
1) Remove the grease filters.
2) Press the carbon filter
against one end of the motor,
the fixing point is in the centre
of the carbon filter.
3) Turn the carbon filter
clockwise, until you feel it click
into place.
o Repeat this process for
the second carbon filter.
You need to place a
carbon filter at either end
of the motor.
o Refit the grease filters.
o The carbon filters should be replaced every 3 - 6 months or if
they show signs of damage.
15
Installation
IMPORTANT: Before installation and usage read
all the instructions and make sure that the
voltage (V) and the frequency (Hz) indicated on
the rating plate are exactly the same as the
voltage and frequency in your home. The rating
plate can be found behind the grease filter.
The manufacturer declines all responsibility in the event of the installer
failing to observe all the accident prevention regulations in force,
which are necessary for normal use and the regular operation of the
electric system.
Electrical connection
YOUR COOKER HOOD IS INTENDED FOR FITTED AND
PERMANENT INSTALLATION.
o The cooker hood’s power cable must be fitted upstream from the
electrical connection, using an omni-polar switch with a contact
distance of at least 3 mm. THE FUSE MUST BE RATED AT 3
AMPS.
WARNING: THIS APPLIANCE MUST BE EARTHED. It
should only be connected by a competent person, using
fixed wiring via a double pole switched fused spur outlet.
(UK ONLY).
We recommend that the appliance is connected by a qualified
electrician, who is a member of the N.I.C.E.I.C. and who will comply
with the I.E.E. and local regulations. The wires in the mains lead are
coloured in accordance with the following UK code:
Blue = Neutral, Brown = Live, Green/Yellow = Ground
If you only find two wires in the main’s lead (blue and brown),
then neither must be connected to the earth terminal.
16
o As the colours of the wires in the appliance’s mains lead may not
correspond with the coloured markings identifying the terminals in
your spur box, please proceed as follows:
o The blue wire must be connected to the
terminal marked “N” (neutral), or coloured
black.
o The brown wire must be connected to the
terminal marked “L” (live), or coloured red.
Before beginning installation
o Check that the product purchased is of a suitable size for the
chosen installation area. In addition check whether there is an
electrical socket available that will be accessible once the hood is
mounted. If the product is going to be used in extraction mode,
then there should also be space to connect a ducting hose to the
outside.
o Carry out all necessary masonry work prior to the fitting of the
cooker hood.
o Ensure that all electrical connections are carried out by a suitably
qualified person.
o Before commencing installation of the cooker hood the grease filters
should be removed.
o Check inside the product and insure that there is no transit
packaging or any other materials, such as packets of screws,
guarantees etc. These should be removed and kept for future use.
o If possible, disconnect and move freestanding or slot-in cookers
from their position, to provide easier access to the rear wall and
ceiling. If this is not possible, then a thick, protective covering
should be placed over the worktop, hob top or cooker. This will help
to protect these surfaces from damage and debris.
o Select a flat surface for assembling the cooker hood. Cover that
surface with a protective covering and place all cooker hood parts
and fittings on to it.
o Rawl plugs are provided to secure the hood to most types of walls
and ceilings. However a qualified technician must verify the
suitability of the materials, in accordance with the type of wall and
ceiling. The wall and ceiling must be strong enough to take the
weight of the hood.
17
o Do not tile, grout or silicone this appliance to the wall. This
appliance is designed to be surface mounted only.
Installing your cooker hood
IMPORTANT: YOU WILL HAVE TO DECIDE BEFORE
INSTALLING YOUR COOKER HOOD WHETHER TO USE
IT IN EXTRACTION MODE OR RECIRCULATION
MODE. PLEASE TURN TO PAGE 28 NOW TO
UNDERSTAND THE DIFFERENCES BETWEEN THESE
TWO MODES.
o We recommend that at least two people install this hood.
o All images are for reference only. There may be some differences
in general appearance to your hood, however the methods of
installation will be the same.
IMPORTANT: YOUR COOKER HOOD SHOULD BE CONNECTED TO
YOUR MAINS SUPPLY AFTER THE REST OF THE INSTALLATION
PROCESS HAS BEEN COMPLETED.
1) Remove the metal grease filters.
2) Position the hood against the wall
that you are intending to install it on and
mark the position of the support holes
that are to be drilled (as shown in the
figure below).
18
2a) The support screw holes
are indicated by figure A in
this
drawing
and
the
anchoring screw holes are
indicated by figure B.
3) Using a drill bit, make holes in the
wall on the positions that you have
marked in step 2.
4) Insert rawl plugs into all of the holes that you have
drilled.
5) Fasten the support screws
halfway in, leaving them 10 mm
out of the wall.
19
6) Hang the hood onto the support
screws.
7) Fully tighten the support screws (A) and then screw the anchoring
screws (B) through the relevant holes in the cooker hood. Fully
tighten the anchoring screws into the wall.
20
Connecting to external ducting
Important: To get the optimum performance from your appliance,
150mm ducting should be used.
8) Connect a 150 mm ducting hose to
the opening at the top of the
motor/hood. (Please note that the
ducting hose is not supplied with the
appliance).
o If you choose to use 125mm ducting,
then please fit the reducer adaptor
(supplied).
o The other end of the ducting hose should be connected to a
discharge outlet that is suitable for cooking vapours. It should
have a cross section of at least 150 cm².
o The maximum distance between the coupling and your discharge
outlet should be 3 metres, with one 90 degree bend. For each
additional 90 degree bend, the maximum distance is reduced by
a further metre.
Fitting the chimney
9) Take the two chimney sections
(C) and (D).
o Rest the bottom of chimney
section (C) on the top of the
hood. You should take care to
position the tabs on the
chimney section into the rear
of the hood.
o Mark the side measurement of
both sides of the chimney
section (C) on the wall with a
pencil.
21
10) Lift chimney section (D) upwards until it reaches the ceiling. You
must ensure that it is perpendicular to the hood.
o Mark the side measurements of both sides of chimney section
(D) on the wall with a pencil and then remove chimney section
(D).
11) Take the flat bracket (E) and place it between the two pencil
marks that you made in step 9
o Keeping the bracket in contact with the wall, use a pencil to
mark on the wall the anchoring holes that are cut out of the
bracket.
22
12) Using a 6 mm drill bit, drill out two holes on the pencil markings
that you made in step 11. Insert rawl plugs into the holes and then
use a screwdriver to secure the fixing bracket to the wall.
o Refit chimney section (C) to the hood and fix it onto the hood
using the two screws that are supplied.
o Secure the top of chimney section (C) to the flat bracket, using
the screws provided.
o Slide chimney section (D) inside of chimney section (C). Then
secure the L shaped bracket to the wall, using the same method
as you have just used to secure the lower bracket.
13) Lift chimney section (D) up to the ceiling and secure it to the L
shaped bracket using the screws provided.
23
Completing the installation
o If you are setting the appliance to recirculation mode, then you
should now fit the two carbon filters. See the “Fitting the carbon
filters” section on page 15.
o The electrical connection must correspond to the electrical
requirement noted on the rating plate, which is placed inside the
cooker hood. The appliance should now be connected to the
electrical supply. See page 16 - 17 for detailed information on
the electrical connection.
o Use a stainless steel cleaner and polish on the stainless steel
sections of the appliance.
o Refit the grease filters and then switch on the mains
supply to the appliance. Check that the appliance is
operating correctly by selecting each speed and
switching the light bulbs on and off.
Extraction mode or recirculation mode?
What is the difference between extraction and recirculation
modes?
o To get optimum performance from your cooker, the air will be
taken out of the room via external ducting.
o Unfortunately if you live in a flat or the hood is too far from an
outside wall, this may not be possible. The only alternative is to
recirculate the air.
o In recirculation mode stale air is taken via the grease filter, and
passed through a charcoal filter for purification. The air then reenters the kitchen via an opening in the hood.
What is a charcoal filter and do I need one?
o All cooker hoods have grease filters but if you are using your
cooker hood in recirculation mode, then charcoal filters must be
fitted in addition to the grease filters.
o IMPORTANT: If you are using the appliance in recirculation
mode, then PLEASE NOTE that some of the vent in the upper
chimney section must be exposed. You will have to take this into
account when calculating the minimum height of the cooker hood
when installed.
24
Troubleshooting
IMPORTANT: If your cooker hood appears not to be operating
properly, before contacting the Baumatic Customer Care
Department, please refer to the checklist below.
My cooker hood will not start.
o Check that the hood is connected to the electricity supply
o Check that the fan speed control is set correctly.
My cooker hood is not working effectively.
o The fan speed is not set high enough
o The grease filters are dirty and require cleaning.
o The kitchen is not well ventilated enough.
o If the hood is set up for recirculation mode, check that the
carbon filters do not need replacing.
o If the hood is set up for extraction mode, check that the ducting
hose and discharge outlet are not blocked.
My cooker hood has switched off during operation.
o The safety cut-out device has been tripped.
o Turn off the hob and then wait for the safety cut-out device to
reset.
o IMPORTANT: If you have installed your cooker hood too low,
the safety cut-out device will frequently trip. Your cooker hood
may become damaged if the safety cut-out device is tripped
frequently.
25
IMPORTANT: If your appliance appears not to be
operating correctly, then you should disconnect it
from your mains supply and then contact
Baumatic Customer Care on telephone number
(0118) 933 6911.
DO NOT ATTEMPT TO REPAIR THE APPLIANCE
YOURSELF.
Please note that if an engineer is asked to attend whilst the product is
under guarantee and finds that the problem is not the result of an
appliance fault, then you may be liable for the cost of the call out
charge.
The appliance must be accessible for the engineer to perform
any necessary repair. If your appliance is installed in such a
way that an engineer is concerned that damage will be caused
to the appliance or your kitchen, then they will not complete a
repair.
This includes situations where appliances have been tiled in,
sealed in with sealant, have wooden obstructions placed in
front of the appliance - like plinths, or any installation other
than the one specified by Baumatic Ltd. has been completed.
Please refer to the conditions of guarantee that appear on the
warranty card that you receive with the appliance.
IMPORTANT: Baumatic Ltd. operates a policy of continuous
improvement and reserves the right to adjust and modify its
products without prior notification.
26
United Kingdom
Baumatic Ltd.,
Baumatic Buildings,
6 Bennet Road,
Reading, Berkshire
RG2 0QX
United Kingdom
Sales Telephone
(0118) 933 6900
Sales Fax
(0118) 931 0035
Customer Care Telephone
(0118) 933 6911
Customer Care Fax
(0118) 986 9124
Spares Telephone
(01235) 437244
Advice Line Telephone
(0118) 933 6933
E-mail:
sales@baumatic.co.uk
customercare@baumatic.co.uk
spares@baumatic.co.uk
technical@baumatic.co.uk
Czech Republic/Slovakia
Baumatic s.r.o.
Lípová 665/1
460 01 Liberec 4
Czech Republic
Panenská 34
811 03 Bratislava - Staré Mesto
Slovakia
+420 483 577 200 (CZ)
+421 255 640 618 (SK)
www.baumatic.cz
www.baumatic.sk
Germany
Kundendienst & Ersatzteile
Deutschland 0049(0)180-5888975
Oesterreich +43 (0) 820 / 420423
www.baumatic.de
Website:
www.baumatic.co.uk
Italy
Baumatic Italia S.R.L.
Via Galvani N.3
35011 Campodarsego (PD)
Facebook:
www.facebook.com/baumatic.uk
+3904 9920 2297
www.baumatic.it
Republic of Ireland
Holland
Baumatic Benelux B.V.
Dukdalfweg 15d
1332 BH ALMERE
Nederland
Service Telephone
1-890 812 724
Spares Telephone
091 756 771
+31(0)36 549 1553/1555
www.baumatic.nl
27
28