Silver 58310101 12 Stitch Mini Sewing Machine Instruction manual

INSTRUCTIONS for the 12 stitch sewing machine
1.Package includes
Sewing machine Zipper foot
Extension table Invisible zipper leg
Needle Feeder (90/14)
Pedal Sewing accessories
Buttonhole foot Instructions
2.Stitch instructions
All 12 built-in stitches, including basic, decorative and blind hems. visible
zipper. Invisible zipper and buttonhole stitches allow you to sew a variety of
projects such as clothing, quilting, crafts, etc.
Point 7:
Buttonhole-Buttonhole lines on long side sidesFoot: Buttonhole foot
Point 8:
Buttonhole-Buttonhole lines on short side sidesFoot: Buttonhole foot
How to do a blind hem:1. Roll up the hem to the desired width and iron. Fold (as shown
in Fig. 1) against the right side of the fabric with the top edge of the hem extending
approximately 7mm (1/4") towards the right side of the folded fabric.
2. Start sewing slowly on the fold. making sure the needle lightly touches the folded top to
catch one or two threads of fabric
3. Unfold the fabric when the hem is finished and iron.
Needle
Size
90/14:
thick.
for
sewing
on
medium
weight
fabrics
up
to
2mm
Backstitch lever function:
Reinforced start 8 end seams for tear resistant. (Only available for basic straight stitches
1-4)
3.Thread the upper thread
1. Put a spool on the thread pin and pull the thread from the spool about 4 inches long.
2. Pass the thread through the tension disc through the gap.
3. Pass the thread from right to left through groove 2 of the take-up lever.
3.(Turn the handwheel counterclockwise to raise the lift lever) Then pass the thread from
right
to
left
through
the
hole
of
the
lift
lever.
5. Pass the thread from right to left through groove 4 of
Lifting lever.
6. Pass the thread through the hole of the needle bar from top to bottom.
7.(Turn the handwheel counterclockwise to raise the needle position at the top of the
presser foot.) Using the threader (included) to pass the thread through through the needle
hole from front to back, and pull the thread out about 4 inches long. (Make sure the thread
length is more than 4 inches before threading, otherwise the thread is hard to find)
4. Straighten the bottom thread
1. Using the presser foot to lift the presser foot.
2. Insert the lower bobbin and pull the thread
approximately 4 inches long. (Make sure the thread length is more than 4 inches before
threading. Otherwise, the thread is difficult to find.)
3. One hand holds the upper thread. Another hand turns the handwheel counterclockwise
so that the needle picks up the lower thread. (Be sure to turn the handwheel
counterclockwise, otherwise the lower thread will not be picked up.)
4. Pull the upper thread until you see that the lower thread comes out of the needle plate
hole with the upper thread. Then pull the lower thread to separate it from the upper thread.
3.Put
foot.
the
upper
thread
to
the
left
and
under
the
presser
6. Upper and lower thread
rear Set.
3.Place your fabric under the presser foot then put down your presser foot after
connecting the power supplies, you can start your sewing now.
3.Replacing the presser foot
1. Turn the handwheel counterclockwise to raise the needle position up from the presser
foot.
2. Using the presser foot to lift the presser foot. Lift the foot lock lever to release the
original presser foot (automatically detaches from the locking device).
Crowbar into locking device hole
4.Remove the presser foot lifter (the hole in the lock will match the new presser foot
holder).
5. Then raise the foot lock lever (the presser foot will automatically engage).
6. Lift the presser foot and it's done.
Tips: When to raise the needle/presser foot
1. Needle
Using the handwheel to control the needle. (as well as the lower thread)
Raise the needle before
a.Putting on/removing the fabric
b.Donning
c.Reinsert a new needle
Place the needle before
has. Sewing
2, presser foot
Using the presser foot lever to control the presser foot.
Raise the front presser foot
a.Putting on/removing the fabric
b.Donning
vs. Change the old presser foot
Lower the front presser foot
has. Sewing
b.Reinsert a new needle
Lower the presser foot after
a.Put the cloth
1. 3.Warning
Do not use as a toy. Children must be accompanied by a guardian when using.
2.Never operate the appliance if the machine's ventilation openings are blocked. Keep the
ventilation openings of the sewing machine and foot control free from accumulation of lint,
dust and loose fabrics,
3.Keep fingers away from all moving parts. Special attention is required around the
sewing machine needle.
4. Do not use bent needles.
5. Do not pull or push the fabric while sewing, this may deflect the needle and cause it to
break.
6. Please turn off the machine or unplug it when the machine is not working properly.
Please read all instructions before using this appliance and retain the instructions
for future reference.
IMPORTANT SAFETY INSTRUCTIONS
This sewing machine is intended for domestic use only:
Do not use outdoors
Powered by AC/DC adapter
The sewing machine should be turned off with the adapter unplugged when:
Thread the needle
Change the needle
Change the lower bobbin
Change of parts
Cleaning the machine
After each use
PRECAUTIONS
Never leave the sewing machine unattended in the presence of children. When
using the sewing machine, keep your hands away from the needle, hand
wheel, upper thread tension dial and pattern selection dial. To clean the sewing
machine, simply wipe it with a soft cloth. and never use harsh chemical
solutions.