SECO-LARM DR-116-1.0TQ Specifications

EV-7605-NYWQ (NTSC)
EV-7605-PYWQ (PAL)
Mini PTZ Camera
Manual




12x Optical zoom and 16x digital zoom
Up to 192x zoom
Up to 360°/sec pan/tilt motion
Outdoor or indoor use
 Up to 256 preset target views, each with
its own characteristics such as white
balance and auto exposure
 Up to 90° tilt, up to 180° with auto-flip
.
NOTE: Products with a model number that ends with “Q” or have a round green “Q” sticker represent RoHs compliant products.
ENFORCER Mini PTZ Camera
Table of Contents:
Introduction ..................................................... 2
Features and Functions .................................. 3
Parts List ......................................................... 4
Specifications .................................................. 4
Pan/Tilt Settings .............................................. 4
Dimensions ..................................................... 5
Safeguards and Precautions ........................... 6
Overview ......................................................... 7
Camera Address DIP Switch and
Communication Protocol Setup ...................... 7
Installation ....................................................... 8
Pre-operation Checklist ................................... 9
Understanding and Operating Preset
and Pattern Functions ................................... 10
Configuring Mini PTZ Camera with
Enforcer DR-1 Series DVR ........................... 11
Reserved Presets .......................................... 12
Configuration Defaults................................... 12
OSD Display .................................................. 13
Operating the OSD Menus ............................ 13
Menu Diagrams .......................................14~16
System Information Menu ............................. 17
Addr Setting Menu ........................................ 17
Motion Menu ........................................... 18~19
Pattern Menu ................................................ 19
Camera Menu ......................................... 20~21
Motion Detect Submenu ............................... 22
Focus Submenu ............................................ 23
Exposure Submenu ...................................... 24
Special Submenu .................................... 25~26
Cruise Setting Menu ..................................... 27
Password Menu ............................................ 27
Display Setup Menu ...................................... 28
Windows Blanking Menu .............................. 28
Alarms Setting Menu .................................... 28
Preset Label Menu ........................................ 29
Restore Factory Default Menu ...................... 29
Reboot System Menu ................................... 29
Preset Worksheet ......................................... 30
Installation Notes .......................................... 31
Troubleshooting ............................................ 32
Also Available from SECO-LARM................. 32
FCC Compliance Statement ......................... 32
Warranty ....................................................... 32
Introduction:
The ENFORCER Mini PTZ Camera is a compact full-featured PTZ (pan/tilt/zoom) CCTV camera. In as little
as one second, the camera can pan a full 360 degrees, tilt up to 90 degrees, or auto-flip 180 degrees. It also
features an optical zoom of up to 12x and a digital zoom of up to 16x, providing a clear view of the entire
protected premises. The 1/4” Interline Transfer CCD provides high-resolution, 600 TV Line images in light as
low as 0.2 Lux for color use and 0.04 Lux for black and white use. A small size and a wide range of
mounting brackets make the ENFORCER Mini PTZ Camera ideal for almost any installation.
The Mini PTZ Camera is controlled with a keyboard controller or a DVR that uses RS-485 for
communicating between the devices.
2
SECO-LARM U.S.A., Inc.
ENFORCER Mini PTZ Camera
Features and Functions:
Powerful and Flexible: The ENFORCER Mini PTZ Camera is equipped with a 1/4” CCD, a powerful Day
and Night function with mechanical ICR, up to 192x zoom (max. 12x optical zoom and 16x digital zoom),
multiple focus modes, and other fully programmable features.
Pan/Tilt Functionality: The camera features 360° endless pan motion and 90° tilt. It can be programmed
to automatically flip the image if it tilts under the unit. The pan/tilt function uses vector drive technology to
quickly move to the target while ensuring the view on the monitor flows smoothly.
On-Screen Display (OSD): The On-Screen Display shows camera status and settings together with the
preset target views.
A Wide Range of Programmable Options:
 Up to 256 preset target views, each with its own characteristics such as zoom and lens angle
 Up to four patterns for moving the camera as if it were controlled by a joystick
 Up to eight privacy masks which can be increased or decreased in size to cover certain areas to
protect privacy
 Frame scan between two preset positions
 Preset cruise for scanning between the first twenty presets
Reserved Presets: Certain camera characteristics can be specified by using reserved preset
configurations instead of individually configuring those characteristics.
Standard PTZ Control: Works with Pelco-D or Pelco-P compatible controllers via an RS-485 connection.
Auto-Flip: Vertically inverts the image if the camera tilts below its center.
Parking Action: Should no operator-activated or automated camera action occur during a specified time
(programmable from 15 to 250 seconds), the camera automatically moves to a pre-determined preset
position or any pre-programmed pattern, frame scan, or other scan function.
Smart Power-Up: The camera automatically moves to a pre-determined preset position or any preprogrammed pattern, frame scan, or other scan function on power-up.
Window Blanking: Up to eight privacy masks can be created to cover certain areas or objects such as
windows or private houses. The masks can be adjusted for size. When the camera moves past such areas
or objects, the mask automatically covers them.
Semi/Auto Focus: The focus for each preset location is manually set, and the camera automatically uses
that focus when it moves to a preset location. During jog operations, the camera uses auto focus. The shift
between semi-auto and auto focus occurs automatically.
SECO-LARM U.S.A., Inc.
3
ENFORCER Mini PTZ Camera
Parts List:
1x Camera
1x Wall-mount bracket
1x Manual
1x Wire harness extension cord
4x Short screws (for attaching camera to bracket)
4x Long screws (for attaching bracket to wall)
4x Screw anchors
Specifications:
Type
CCD
Resolution
Video output format
Effective pixels
SSNR (Noise Reduction)
SSDR (Dynamic Range)
Day/Night
OSD Control
Protocols
Scanning system
Sync
Video output
Lens
Zoom
Minimum illumination
Gamma correction
S/N Ratio
DSS (Digital Slow Shutter)
Shutter control
Gain control
White balance
Operating voltage
Camera only
Power
Camera w/ fan
Consumption
Camera w/ fan and heater
IP Rating
Operating temperature
Dimensions
Cable length
Weight
EV-7605-NYWQ
EV-7605-PYWQ
Mini PTZ Camera
¼” Interline transfer
600TVL
NTSC
PAL
768x494 pixels
752x582 pixels
Low, middle, high, off
Off, on
Auto, Color, B/W (ICR)
RS-485
Pelco-D, Pelco-P (automatic)
2:1 Interlace
Internal/Line-Lock
1.0Vp-p Composite video, 75Ω
3.94~46.05mm
12x Optical / 16x Digital
Color: 0.2 Lux / B/W: 0.04 Lux
Default
52dB (AGC Off)
x2~x512
1/60~1/120,000 s
Off, Low, Middle, High, Manual
ATW, AWC, Indoor, Outdoor, Manual
24VAC
9W
10W
20W
IP66
-4°F~131°F (-20°C~55°C)
413/16”x7”x413/16” (122x180x122 mm)
31.5” (80cm)
42.3-oz (1.2kg)
Pan/Tilt Settings:
Range
Pan/Tilt Speed
Presets
Patterns
4
Pan
Tilt
Preset
Manual
Swing
360°
180°
Up to 360°/s
0.05~360°/s (proportional to zoom)
1~180°/s
Max. 256 presets (Label, camera image setting)
Max. 4 patterns
SECO-LARM U.S.A., Inc.
ENFORCER Mini PTZ Camera
Dimensions:
Camera
Side
Bottom
6”
(152mm)
7”
(180mm)
413/16”
(122mm)
Wall-Mount Bracket
Side
Bottom
31/8”
(80mm)
411/16”
(119mm)
61/2”
(166mm)
SECO-LARM U.S.A., Inc.
5
ENFORCER Mini PTZ Camera
Safeguards and Precautions:
Before Starting:
1. Please read this manual carefully and keep it for future reference.
2. Use the camera within given temperature and electrical limits.
3. Do not point the camera at the sun. Heat could damage the camera, even when not in use.
4. Do not expose the camera to rain or moisture.
5. Do not install the camera in dusty or humid environments.
6. Do not mount the camera in areas exposed to radiation, strong magnetic fields, or strong electrical
signals.
7. Do not open or disassemble the camera. There are no field-serviceable parts inside.
8. Do not drop the camera or subject it to strong vibrations.
9. This camera is VERY HEAVY. To prevent injury to the installer or the client, do not mount it on an
unstable or improperly supported surface. When mounting, only use brackets or other mounting devices
that are recommended in this manual.
Operation Precautions:
1. Only use regulated power supplies with voltage and minimum current output per the specifications of
this camera.
2. If the camera gets hot or starts smoking while in use, disconnect the power immediately and contact the
professional installer or dealer.
Cleaning Precautions:
1. Periodically clean the dust off the entire camera with a slightly damp (NOT WET) cloth. DO NOT USE
chemical cleaners.
2. Do not move the camera while cleaning, as this could change the angle of the view.
3. If the dome cover becomes dusty, carefully clean using a slightly damp (NOT WET) cloth. DO NOT USE
chemical cleaners. DO NOT SCRATCH the dome, as this will affect the quality of the video image.
6
SECO-LARM U.S.A., Inc.
ENFORCER Mini PTZ Camera
Overview:
Wall mount
bracket
Camera
DIP Switches
Lens
Turn counterclockwise to
remove
Dome
Camera Address DIP Switch and Communication Protocol Setup:
Before the Mini PTZ Camera is installed, first set up the DIP switches to configure the camera address. The
communication protocol is configured automatically by the camera.
1. Remove the clear dome of the Mini PTZ Camera by turning it counterclockwise by hand.
2. Look for the DIP switch block near the base of the black plastic dome that surrounds the camera. DO
NOT REMOVE THE BLACK PLASTIC DOME.
3. Set the camera address (8-pin DIP switch):
 The camera address is a number from 1 to 255. The factory default camera address is "1".
 Do not use "0" as a camera address.
 The address of a particular camera must match the address setting of the DVR or keyboard
controller.
 To get the camera address, add the total DIP switches that are in the ON position.
 Example: If DIP switches 1, 4, and 6 are ON then the camera address is 1+8+32=41.
:
8
7
6
5
4
3
2
1
OFF
ON
Value 128
64
32
16
8
SECO-LARM U.S.A., Inc.
4
2
1
7
ENFORCER Mini PTZ Camera
Installation:
1. Connect the camera to either the included wall mount or another optional bracket.
2. Run a 24VAC power supply wire, a video cable with a male BNC connector, and a data wire through the
wall to where the camera is to be mounted.
3. Connect the camera's video cable to the video cable coming from the wall. Do not cut the female BNC
connector of the camera's video cable as that will void the warranty.
4. Connect the camera's RS-485 cable to the data wire cable coming from the wall.
5. Temporarily connect the camera to the power supply. Do not cut the AC power terminal of the
camera's power cable as that will void the warranty.
6. Hold the camera's bracket against the wall or ceiling where it is to be mounted, but do not mount yet.
While watching the monitor, operate the camera's pan and tilt functions to ensure that this mounting
location is correct. Use a pencil to mark the location of the screw holes in the mounting bracket.
7. Disconnect the power supply from the camera.
8. Mount the mounting bracket to the wall or ceiling using the included mounting screws. If the wall is
made of drywall, brick, or similar material, it may be necessary to use the included screw anchors.
9. Reconnect the camera's power supply.
10. Program the camera via the OSD (on-screen display) menus from the DVR or keyboard controller.
11. Do a final test of the video camera and monitor.
:
Basic Installation
24VAC Jack
Coaxial cable
RS-485 (+) (Purple)
RS-485 (-) (Yellow)
Multiple PTZ Camera Installation
DR-1 Series DVR
RS-485
#1
8
#2
#n
SECO-LARM U.S.A., Inc.
ENFORCER Mini PTZ Camera
Pre-Operation Checklist:
Before operating the Mini PTZ Camera, please note the following:
:
 Double-check that the cables are properly run between the controller and camera, and that all
connections are correct.
 Double-check that the camera address on the controller is the same as the address of the target
camera. The camera address can be found by looking at the camera address DIP switch settings
(see page 7) or through the ADDR SETTING menu in the OSD (see page 17).
 The Pelco protocol setting of the controller and the camera must be identical. The Pelco protocol setting
of the camera is automatically matched to the communication protocol of the controller or DVR.
 Make sure that the camera is rebooted after the camera address setup DIP switches are changed.
 Refer to the controller or DVR manual for information on configuring or operating those devices.
SECO-LARM U.S.A., Inc.
9
ENFORCER Mini PTZ Camera
Understanding and Operating Preset and Pattern Functions:
Standard Pelco-compatible controllers allow the camera operator to do several functions without going
through the full OSD menu, depending on the capabilities of the DVR to which the camera is connected.
:
The SECO-LARM series of DVRs allows operators to do the following via the "Dome Preset" menu:
 Set the camera to remember multiple specific preset locations.
 Tell the camera to go to a specific preset location.
 Run certain preset functions, including patterns, frame scan, or preset cruise functions.
 Change certain configuration patterns.
Programming the patterns, frame scan, preset cruise, and a detailed configuration of the PTZ camera
requires operators to use the OSD menu. See page 16 for more information.
This PTZ camera can be controlled by any DVR or keyboard controller which uses Pelco-compatible
protocols. When using non-SECO-LARM DVRs or when using keyboard controllers, the manuals for those
devices may include information on how to operate or program the PTZ camera.
To set or go to a preset location or use a preset function via a SECO-LARM DVR:
1. Press the "Dome" button. The lower left corner of the screen will change from "REC" to "DOME" to
show the camera is in the Dome Control menu.
2. Press the "1" button to go to the DOME PRESET menu.
3. Use the UP, DOWN, LEFT, and RIGHT buttons to highlight your selection and press ENTER to confirm
your selection.
Note: In most cases, only the GO function will work. Only the preset locations can be programmed via
the DOME PRESET menu. Other functions must be programmed using the OSD menu.
4. Use the UP and DOWN arrows to switch between YES and NO. Navigate to YES, and then press the
ENTER button.
See page 12 for a list of preset functions.
10
SECO-LARM U.S.A., Inc.
ENFORCER Mini PTZ Camera
Configuring Mini PTZ Camera with Enforcer DR-1 Series DVR:
:Step 1
Press Dome on the DVR front panel to access DVR
controls.
Step 2
Press 1 to access the DVR preset menu.
Step 3
Use the Up, Down, Left, Right, and Enter buttons
to make a selection.
Step 4
Go to Preset 95 to access Mini PTZ OSD settings.
This will bring up the SPEED DOME CAMERA menu as shown on page 18.
SECO-LARM U.S.A., Inc.
11
ENFORCER Mini PTZ Camera
Reserved Presets:
:
<Go Preset> [82]
Pan Preset> [83]
<Go
<Go Preset> [84~87]
<Go Preset> [88]
<Go Preset> [89]
<Go Preset> [90]
<Go Preset> [91]
<Go Preset> [92]
<Go Preset> [95]
<Go Preset> [98]
<Go Preset> [99]
Start Frame Scan function
Clear all Presets
Run Pattern function 1~4
Run Preset 1~10 Cruise function
Run Preset 11~20 Cruise function
Run Preset 21~30 Cruise function
Run Preset 31~40 Cruise function
Run 360° Random Interval Scan function
Enter into OSD menus
Run 360° Continuous Scan function
Run Preset Cruise function
Configuration Defaults:
:
12
Default Display Configuration
Preset Label
ON
Zoom
ON
P/T Deg
ON
Camera Title
OFF
Camera ID
OFF
Camera Info
OFF
Motion Alarm
OFF
Zoom Mag
OFF
Default Motion Configuration
Power Up
NONE
Park Time
15s
Park Action
NONE
Dome Speed
4
User Edit Data
Preset 1~81, 100~256
UNDEFINED
Frame Scan
UNDEFINED
Pattern 1~4
UNDEFINED
Default Camera Configuration
SSDR
ON
White Balance
ATW
Backlight
OFF
Motion Detect
OFF
Focus Mode
AUTO
Digital Zoom
OFF
Brightness
50
Iris
AUTO
AGC
HIGH
SSNR3
ON
SENS-UP
AUTO
Day/Night
AUTO
SECO-LARM U.S.A., Inc.
ENFORCER Mini PTZ Camera
OSD Display:
:
Camera Title
Action Title
CAMERA TITLE
PRESET 1
0/42
x1
Pan/Tilt Information
Zoom Information
Operating the OSD Menus:
For operating the OSD menus, please note the following:
:




To access the OSD menu from your DVR, go to Preset 95. For more information on DVR presets and
their functions for the ENFORCER Mini PTZ Camera, please see page 11, Reserved Presets.
Most commands are done on PELCO-compatible DVRs using the front panel buttons, including up,
down, right, and left arrows, or via a panel-mounted joystick. Such operations may also be possible
using the DVR’s remote control.
For many menu operations, the user must press the MODE or PLAY/STOP buttons. For most DVRs,
these are the buttons for iris open (MODE) and iris close (PLAY/STOP), but may be marked with other
words.
For ENFORCER DR-1 Series DVRs, the operations are done as follows:
– To navigate the menus, press the UP/DOWN/LEFT/RIGHT buttons.
– To enter a sub-menu (except for the CAMERA sub-menu), press the MODE or
RIGHT buttons.
– To enter a sub-menu in the CAMERA sub-menu, press the MODE button.
– To exit all menus (except for the CAMERA sub-menu), press the PLAY/STOP button.
PLAY/STOP and MODE
buttons
SECO-LARM U.S.A., Inc.
13
ENFORCER Mini PTZ Camera
Menu Diagram:
(see pg. 17)
:
SETUP MENU
SETTING
SYSTEM
INFORMATION
COM
ADDRESS
SOFTWARE VERSION
ADDR TYPE
ADDR SOFT
ADDR HARD
(see pg. 18)
ADDR SETTING
(see pg. 18)
FRAME SCAN
MOTION
(see pg. 19~20)
POWER UP
PARK TIME
PARK ACTION
PATTERN
(see pg. 20)
DOME SPEED
PATTERN NUMBER
PROGRAM PATTERN
CLEAR CURRENT PATTERN
CLEAR ALL PATTERNS
SSDR
WHITE BALANCE
CAMERA
BACKLIGHT
14
SETTING OPTIONS
HARD / SOFT
1~255
SET SCAN POSITION
CLEAR FRAME SCAN
FRAME SCAN SPEED: 1~32
NONE / AUTO SCAN / RANDOM SCAN / FRAME SCAN /
PRESET 1 / PRESET 8 / PATTERN 1 / PATTERN 2 /
PATTERN 3 / PATTERN 4 / CRUISE
15~250S
NONE / AUTO SCAN / RANDOM SCAN / FRAME SCAN /
PRESET 1 / PRESET 8 / PATTERN 1 / PATTERN 2 /
PATTERN 3 / PATTERN 4 / CRUISE / REPEAT LAST
1~8
1~4
ON: SSDR: 1~15
D-RANGE: NARROW / WIDE
OFF
ATW
MANUAL: RED: 0~1023
BLUE: 0~1023
AWC→SET
OUTDOOR
INDOOR
OFF
BLC: LEVEL: LOW / MIDDLE / HIGH
TOP: 0~68
BOTTOM: 32~100
LEFT: 0~70
RIGHT: 30~100
HLC: LEVEL: LOW / MIDDLE / HIGH
MASK TONE: 0~15
SECO-LARM U.S.A., Inc.
ENFORCER Mini PTZ Camera
Menu Diagram:
:
SETUP MENU
SETTING
SETTING OPTIONS
OFF
CAMERA –
MOTION DETECT
ON
MODE
ZOOM TRACK
ZOOM SPEED
D-ZOOM
CAMERA –
FOCUS
ZOOM POS INIT
USER PRESET
LENS INIT
BRIGHTNESS
IRIS
SHUTTER
CAMERA –
EXPOSURE
AGC
SSNR3
SENS-UP
SECO-LARM U.S.A., Inc.
AREA SELECT: AREA1~AREA8
AREA MODE: ON: TOP: 1~26
BOTTOM: 5~30
LEFT: 1~44
RIGHT: 5~48
OFF
SENSITIVITY: LOW / HIGH
SMART ZOOM: OFF
ON: START ZOOM: x1~x12
TARGET ZOOM: x1~x12
DWELL TIME: 5~60 SEC
AUTO: TELE / WIDE
ONE-PUSH: TELE / WIDE / NEAR / FAR
MANUAL: TELE / WIDE / NEAR / FAR
AUTO TRACK / TRACK / OFF
SLOW / MEDIUM / FAST
OFF
ON: LIMIT: x2~x16
OFF
AUTO
MANUAL: POS INIT: x1~x12
OFF
ON: PRESET NO: 1~128: TELE / WIDE / NEAR / FAR
PRESET SAVE
PRESET CLEAR
MANUAL
AUTO: DAY: 1~7
1~100
AUTO
MANUAL: IRIS F-NO: F1.6~F28, CLOSE
___
MANUAL: MANUAL: 1/60~1/120,000, x512~x2
A. FLK
ESC
OFF
LOW
MEDIUM
HIGH
MANUAL: AGC VAL: 5dB~41dB
OFF
ON: LEVEL: 1~32
___
OFF
AUTO: LIMIT: x2~x512
___
15
ENFORCER Mini PTZ Camera
Menu Diagram:
:
SETUP MENU
SETTING
DAY/NIGHT
DIS
SYNC
IMAGE ADJ
CAMERA –
SPECIAL
MONITOR
DISPLAY
SETTING OPTIONS
AUTO: DWELL TIME: 5~60 SEC
DURATION: SLOW / FAST
EXT
COLOR: BURST LEVEL: 0~100
B/W: BURST MODE: ON / OFF
OFF / ON
INT
H-REV: OFF / ON
V-REV: OFF / ON
SHARPNESS: ON: LEVEL: 1~31
OFF
CRT: PED LEVEL: 0~70
COLOR LEVEL: 1~100
LCD: GAMMA: 0.20~1.0
PED LEVEL: 0~70
COLOR LEVEL: 1~100
USER: GAMMA: 0.20~1.0
PED LEVEL: 0~70
COLOR LEVEL: 1~100
CAM TITLE: OFF
ON: Select camera title
CAM ID: OFF / ON
CAM INFO: OFF / ON
MOTION ALARM: OFF / ON
ZOOM MAG: OFF / ON
OSD COLOR: WHITE / YELLOW / GREEN / RED / BLUE
LANGUAGE: ENGLISH / KOREAN / JAPENESE /
SPANISH / FRENCH / PORTUGUESE
5~250 seconds
ON / OFF
OFF / ON
Modify password for OSD access
ON / OFF
ON / OFF
ON / OFF
1~8
Edit size and location of privacy window
OFF / ON
Clear selected privacy window
Reserved for future use
1~79
Set selected preset label
Clear selected preset label
DWELL TIME
PRESET (1~20)
ENABLE PASSWORD
PASSWORD
EDIT PASSWORD
PRESET LABEL
DISPLAY SETUP
ZOOM
P/T DEG
WINDOW NUMBER
EDIT WINDOW LOCATION
WINDOWS BLANKING
ENABLE WINDOW
CLEAR WINDOW
ALARMS SETTING
ALARM ACT (1~4)
PRESET
PRESET LABEL
SET PRESET LABEL
CLEAR PRESET LABEL
RESTORE FACTORY
Restores factory defaults (except CAMERA section)
DEFAULT
REBOOT SYSTEM
Reboot and go through start-up features
EXIT
Exit menu and save settings
CRUISE SETTING
16
SECO-LARM U.S.A., Inc.
ENFORCER Mini PTZ Camera
SYSTEM INFORMATION Menu:
From MAIN MENU
This menu shows the current configuration information of the Mini PTZ Camera. No information can be
programmed using this OSD menu.





COM: Displays current serial baud rate, parity, data bits,
and stopped position of the camera.
ADDRESS: Displays the currently set address.
SOFTWARE VERSION: Displays the software version.
BACK: Return to previous menu.
EXIT: Exit OSD menus.
SYSTEM INFORMATION
COM
9600, N, 8, 1
ADDRESS
6
SOFTWARE VERSION V5.3.2
BACK
EXIT
ADDR SETTING Menu:
From MAIN MENU
This menu allows for setting the address via the DIP switches or via the Mini PTZ software.





ADDR TYPE: Set the address type.
– HARD: Set via hardware DIP switches.
– SOFT: Set via software.
ADDR SOFT: Set the soft address.
– 1~255
ADDR TYPE: Display the current DIP switch address.
BACK: Return to previous menu.
EXIT: Exit OSD menus.
SECO-LARM U.S.A., Inc.
ADDR SETTING
ADDR TYPE
HARD
ADDR SOFT
1
ADDR HARD
1
BACK
EXIT
17
ENFORCER Mini PTZ Camera
MOTION Menu:
From MAIN MENU
This menu allows for setting different Mini PTZ movement options such as frame scan, power up operation,
and park action.

FRAME SCAN: The camera will pan between two
positions at a given angle.
SET SCAN POSITION: Set left and right frame scan
positions.
CLEAR FRAME SCAN: Clear the frame scan
positions.
– FRAME SCAN SPEED: Set the frame scan speed.
 1~32
– BACK: Return to previous menu.
– EXIT: Exit OSD menus.
POWER UP: The camera will perform one of the below
actions.
– NONE: No action.
– AUTO SCAN: Continuous clockwise scan at given
tilt and zoom.
– RANDOM SCAN: Intermittent clockwise scan at
given tilt and zoom.
– FRAME SCAN: Continuous scan between two
positions.
– PRESET 1: Move to the Preset 1 position.
– PRESET 8: Move to the Preset 8 position.
– PATTERN 1: Perform the Pattern 1 action.
– PATTERN 2: Perform the Pattern 2 action.
– PATTERN 3: Perform the Pattern 3 action.
– PATTERN 4: Perform the Pattern 4 action.
– CRUISE: Perform the Cruise action between
Presets 1 through 20.
MOTION
FRAME SCAN
POWER UP
PARK TIME
PARK ACTION
DOME SPEED
BACK
EXIT
FRAME SCAN
SET SCAN POSITION
CLEAR FRAME SCAN
FRAME SCAN SPEED 16
BACK
EXIT
SET SCAN POSITION
LEFT LIMIT POSITION
IRIS OPEN TO CONTINUE
340/42
18
NONE
15S
NONE
4
X1
SECO-LARM U.S.A., Inc.
ENFORCER Mini PTZ Camera
MOTION Menu, continued:





PARK TIME: Idle time required before Park Action.
– 15~250 seconds
PARK ACTION: The camera will perform one of the below actions.
– NONE: No action.
– AUTO SCAN: Continuous clockwise scan at given tilt and zoom.
– RANDOM SCAN: Intermittent clockwise scan at given tilt and zoom.
– FRAME SCAN: Continuous scan between two positions.
– PRESET 1: Move to the Preset 1 position.
– PRESET 8: Move to the Preset 8 position.
– PATTERN 1: Perform the Pattern 1 action.
– PATTERN 2: Perform the Pattern 2 action.
– PATTERN 3: Perform the Pattern 3 action.
– PATTERN 4: Perform the Pattern 4 action.
– CRUISE: Perform the Cruise action between Presets 1 through 20.
– REPEAT LAST: Repeat the last action.
DOME SPEED: Speed at which the Power Up Action and Park Action will move.
– 1~8
BACK: Return to previous menu.
EXIT: Exit OSD menus.
PATTERN Menu:
From MAIN MENU
This menu allows for programming up to 4 unique patterns each with up to 100 actions including pan, tilt,
and zoom actions.





PATTERN NUMBER: Choose which pattern to set.
– 1~4
PROGRAM PATTERN: Program the chosen pattern
with up to 100 actions including pan tilt and zoom.
CLEAR CURRENT PATTERN: Clear the chosen
pattern.
CLEAR ALL PATTERNS: Clear all patterns.
BACK: Return to previous menu.
EXIT: Exit OSD menus.
PATTERNS
PATTERN NUMBER
1
PROGRAM PATTERN
CLEAR CURRENT PATTERN
CLEAR ALL PATTERNS
BACK
EXIT
PROGRAM PATTERN
MOVE THE CAMERA TO THE
STARTING POSITION
IRIS OPEN TO CONTINUE
340/42
SECO-LARM U.S.A., Inc.
X1
19
ENFORCER Mini PTZ Camera
CAMERA Menu:
From MAIN MENU
This menu allows for setting different camera options such as SSDR, white balance, backlight, motion
detection, and exposure settings. Use the MODE (IRIS OPEN) key to enter submenus in this menu.


20
SSDR: Set dynamic range on or off.
ON: Turns SSDR on and enters SSDR sub-menu.
 SSDR
o 1~15
 D-RANGE
o NARROW: Set for low light level.
o WIDE: Set for high light level.
 RETURN : Return to the previous camera
menu.
– OFF
WHITE BAL: Adjust the color temperature and image
color.
– ATW: Set Automatic Tracking White Balance on.
MANUAL: Manually set the white balance.
 RED: Set the red gain.
o 0~1023
 BLUE: Set the blue gain.
o 0~1023
 RETURN : Return to the previous camera
menu.
– AWC→SET: Press Iris Open when the camera is
focused on a plain white sheet of paper.
– OUTDOOR: Set the white balance for an outdoor
environment.
– INDOOR: Set the white balance for an indoor
environment.
MAIN SETUP
SSDR
WHITE BAL
BACKLIGHT
MOTION DET
FOCUS
EXPOSURE
SPECIAL
RESET
EXIT
ON
ATW
OFF
OFF
SSDR SETUP
SSDR
-------x------- 8
D-RANGE
NARROW
RETURN
WHITE BAL MANUAL SETUP
RED
-------x-------529
BLUE
-------x-------532
RETURN
SECO-LARM U.S.A., Inc.
ENFORCER Mini PTZ Camera
CAMERA Menu, continued:



BACKLIGHT: Choose either Back Light Compensation
BLC SETUP
LEVEL
LOW
or High Light Compensation.
TOP
--x------------ 30
– OFF: Turn BLC and HLC off.
BOTTOM
------------x-- 75
BLC: Select an area to view clearly, even with a
LEFT
--x------------ 30
RIGHT
------------x-- 70
strong backlight.
RETURN
 LEVEL
o LOW
o MIDDLE
o HIGH
 TOP
o 0~68
HLC SETUP
LEVEL
MIDDLE
 BOTTOM
MASK TONE
-------x------- 7
o 32~100
RETURN
 LEFT
o 0~70
 RIGHT
o 30~100
 RETURN : Return to the previous camera
menu.
HLC: Improve the clarity of the picture by blocking a
strong backlight.
 LEVEL
o LOW
o MIDDLE
o HIGH
 MASK TONE: Adjust the color tone.
o 0~15
 RETURN
MOTION DET: Set motion detection options such as Area, Sensitivity, and Smart Zoom. See page 22
for more information.
FOCUS: Set focus options. See page 23 for more information.
EXPOSURE: Set exposure options such as Brightness, Iris, Shutter, and AGC. See page 24 for more
information.
SPECIAL: Set special options such as Day/Night and Image Reverse. See page 25~26 for more
information.
RESET: Reset the Camera OSD settings to factory default.
EXIT: Exit OSD menus.
SECO-LARM U.S.A., Inc.
21
ENFORCER Mini PTZ Camera
MOTION DET Submenu:
From Camera Menu
This menu allows for setting motion detection options such as area, sensitivity, and smart zoom. Use the
MODE (IRIS OPEN) key to enter submenus in this menu.





22
AREA SEL: Select one of up to eight motion detection
areas.
– AREA1~AREA8
AREA MODE: Turn on or off motion detection for each
selected area.
ON
 TOP
o 1~26
 BOTTOM
o 5~30
 LEFT
o 1~44
 RIGHT
o 5~48
– OFF
SENSITIVITY: Set the motion detection sensitivity.
– LOW
– HIGH
SMART ZOOM: Set if the Mini PTZ will zoom in to the
selected area when motion is detected.
– OFF
ON
 START ZOOM
o x1~x12
 TARGET ZOOM
o x1~x12
 DWELL TIME
o 5~60 SEC
RETURN : Return to the previous camera menu.
MD SETUP
AREA SEL
AREA MODE
SENSITIVITY
SMART ZOOM
RETURN
AREA1
ON
LOW
OFF
AREA SETUP
TOP
--x------------ 8
BOTTOM
----x---------- 14
LEFT
x-------------- 5
RIGHT
--x------------ 12
RETURN
SMART ZOOM SETUP
START ZOOM
X1
TARGET ZOOM
X5
DWELL TIME
5 SEC
RETURN
SECO-LARM U.S.A., Inc.
ENFORCER Mini PTZ Camera
FOCUS Submenu:
From Camera Menu
This menu allows for setting focus options such as zoom speed, digital zoom, and user presets. Use the
MODE (IRIS OPEN) key to enter submenus in this menu.








MODE: Set the camera focus mode.
AUTO: Set the focus automatically.
 TELE / WIDE
ONE-PUSH: Set the focus as the center of the
image.
 TELE / WIDE / NEAR / FAR
MANUAL: Set the focus manually.
 TELE / WIDE / NEAR / FAR
ZOOM TRACK: Set the focus to follow the zoom.
– AUTO TRACK
– TRACK
– OFF
ZOOM SPEED: Adjust the zoom speed.
– SLOW
– MEDIUM
– FAST
D-ZOOM: Set digital zoom on or off.
– OFF
ON
 LIMIT
o x2~x16
ZOOM POS INIT: Set the initial zoom position.
– OFF
– AUTO
MANUAL
 POS INIT
o x1~x12
USER PRESET: Set the focus for individual presets.
– OFF
ON
 PRESET NO
o 1~128
 TELE / WIDE / NEAR / FAR
LENS INIT: Set the lens to self-check on power-up.
– MANUAL
AUTO
 DAY
o 1~7
RETURN : Return to the previous camera menu.
SECO-LARM U.S.A., Inc.
FOCUS SETUP
MODE
AUTO
ZOOM TRACK AUTO TRACK
ZOOM SPEED
FAST
D-ZOOM
OFF
ZOOM POS INIT
OFF
USER PRESET
OFF
LENS INIT
MANUAL
RETURN
D-ZOOM LIMIT SETUP
LIMIT
X2
RETURN
ZOOM INIT POS SETUP
POS INIT
X1
RETURN
USER PRESET SETUP
PRESET NO
x---------PRESET SAVE
PRESET CLEAR
RETURN
1
23
ENFORCER Mini PTZ Camera
EXPOSURE Submenu:
From Camera Menu
This menu allows for setting exposure options such as brightness, auto iris, shutter speed, AGC, and
sens-up. Use the MODE (IRIS OPEN) key to enter submenus in this menu.







1
2
24
BRIGHTNESS: Adjust the brightness of the image.
– 1~100
IRIS: Set the iris control.
– AUTO
– MANUAL
 IRIS F-NO
o F1.6~F28, CLOSE
SHUTTER1: Set the shutter control.
– ___
– MANUAL
 MANUAL
o 1/60~1/120,000, x512~x2
– A.FLK
AGC2: Adjust the automatic gain control.
– OFF
– LOW
– MEDIUM
– HIGH
– MANUAL
 AGC VAL
o 5dB~41dB
SSNR3: Adjust the noise reduction level.
– OFF
– ON
 LEVEL
o 1~32
SENS-UP: Adjust the digital slow shutter level.
– OFF
– AUTO
 LIMIT
o x2~x512
RETURN : Return to the previous camera menu.
EXPOSURE SETUP
BRIGHTNESS -------x------- 1
IRIS
AUTO
SHUTTER
_ _ _
AGC
HIGH
SSNR3
ON
SENS-UP
AUTO
RETURN
If SHUTTER set to MANUAL or A.FLK then SENS-UP is
preset to OFF.
If AGC is set to OFF or MANUAL then SSNR3 and
SENS-UP are preset at OFF.
SENS-UP LIMIT SETUP
LIMIT
X2
RETURN
IRIS MANUAL SETUP
IRIS F-No
F1.6
RETURN
SHUTTER MANUAL SETUP
MANUAL
1/60
RETURN
GAIN MANUAL SETUP
AGC VAL
5dB
RETURN
SSNR3 LEVEL SETUP
LEVEL
-------x------RETURN
1
SECO-LARM U.S.A., Inc.
ENFORCER Mini PTZ Camera
SPECIAL Submenu:
From Camera Menu
This menu allows for setting options such as Day/Night, image reverse, and monitor settings. Use the
MODE (IRIS OPEN) key to enter submenus in this menu.



DAY/NIGHT: Set the Day/Night mode.
AUTO: The image will automatically switch from
color to B/W mode when the ambient light is low.
 DWELL TIME
o 5~60 SEC
 DURATION
o SLOW
o FAST
– EXT: Not used.
COLOR: The image will always display in color.
 BURST LEVEL
o 0~100
B/W: The image will always display in B/W.
 BURST MODE
o ON
o OFF
DIS: Set digital image stabilization on or off.
– OFF
– ON
SYNC
– INT: Not adjustable.
IMAGE ADJ: Set horizontal and vertical reverse, as well
as image sharpness.
– H-REV: Reverse the image horizontally.
 OFF
 ON
– V-REV: Reverse the image vertically.
 OFF
 ON
SHARPNESS: Set the image sharpness level.
 ON
o LEVEL
 1~31
 OFF
SECO-LARM U.S.A., Inc.
SPECIAL SETUP
DAY/NIGHT
AUTO
DIS
OFF
SYNC
INT
IMAGE ADJ
MONITOR
CRT
DISPLAY
RETURN
DAY/NIGHT AUTO SETUP
DWELL TIME
5 SEC
DURATION
SLOW
RETURN
BURST LEVEL SETUP
BURST LEVEL -------x------- 50
RETURN
BURST MODE SETUP
BURST MODE
RETURN
IMAGE SETUP
H-REV
V-REV
SHARPNESS
RETURN
ON
OFF
OFF
ON
SHARPNESS LEVEL SETUP
LEVEL
-------x------- 16
RETURN
25
ENFORCER Mini PTZ Camera
SPECIAL Menu, continued:

26
MONITOR: Set the image to perform better on specific
CRT MONITOR SETUP
PED LEVEL
----x---------- 17
monitor types.
COLOR LEVEL -------x------- 50
CRT: Choose for CRT monitors.
RETURN
 PED LEVEL: Adjust the brightness level.
o 0~70
 COLOR LEVEL: Adjust the color level.
o 1~100
LCD: Choose for LCD monitors.
 GAMMA: Adjust the gray value level.
o 0.20~1.0
 PED LEVEL: Adjust the brightness level.
LCD MONITOR SETUP
GAMMA
0.45
o 0~70
PED
LEVEL
----x---------17
 COLOR LEVEL: Adjust the color level.
COLOR LEVEL -------x------- 50
o 1~100
RETURN
USER
 GAMMA: Adjust the gray value level.
o 0.20~1.0
 PED LEVEL: Adjust the brightness level.
o 0~70
 COLOR LEVEL: Adjust the color level.
o 1~100
USER MONITOR SETUP
DISPLAY: Set the camera OSD display options.
GAMMA
0.55
PED LEVEL
----x---------- 17
– CAM TITLE: Set the camera title.
COLOR LEVEL -------x------- 50
 OFF
RETURN
ON
– CAM ID: Not used.
 OFF
 ON
– CAM INFO: Not used.
 OFF
 ON
DISPLAY SETUP
– MOTION ALARM: Set the motion detection info
CAM TITLE
OFF
CAM ID
OFF
display.
CAM INFO
OFF
 OFF
MOTION ALARM
OFF
ZOOM MAG
OFF
 ON
OSD COLOR
WHITE
– ZOOM MAG: Set the zoom magnification level
LANGUAGE
ENGLISH
display.
RETURN
 OFF
 ON
– OSD COLOR: Set the camera sub-menu OSD color.
 WHITE / YELLOW / GREEN / RED / BLUE
– LANGUAGE: Set the camera sub-menu OSD language.
 ENGLISH / KOREAN / JAPANESE / SPANISH / FRENCH / PORTUGUESE
RETURN : Return to the previous camera menu.
SECO-LARM U.S.A., Inc.
ENFORCER Mini PTZ Camera
CRUISE SETTING Menu:
From MAIN MENU
This menu allows for setting the dwell time and active presets for the Preset Cruise.



DWELL TIME: Set the amount of time the camera will
remain at each preset.
– 5~250 SEC
PRESET 1~20: Set presets to include in the preset
cruise.
– ON
– OFF
BACK: Return to previous menu.
CRUISE SETTING
DWELL TIME (SECS)
PRESET1
PRESET2
PRESET3
PRESET4
PRESET5
PRESET6
PRESET7
PRESET8
PRESET9
PRESET10
8
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
CRUISE SETTING
PRESET11
ON
PRESET12
ON
PRESET13
ON
PRESET14
ON
PRESET15
ON
PRESET16
ON
PRESET17
ON
PRESET18
ON
PRESET19
ON
PRESET20
ON
BACK
PASSWORD Menu:
From MAIN MENU
This menus allows for setting a password to limit access to the OSD.



ENABLE PASSWORD: Enable OSD password.
– OFF
– ON
EDIT PASSWORD: Set OSD password.
BACK: Return to previous menu.
EXIT: Exit OSD menus.
SECO-LARM U.S.A., Inc.
PASSWORD
ENABLE PASSWORD
EDIT PASSWORD
BACK
EXIT
OFF
27
ENFORCER Mini PTZ Camera
DISPLAY SETUP Menu:
From MAIN MENU
This menu allows for setting display options such as preset labels, zoom information, and pan/tilt
information.





PRESET LABEL: Set preset labels on or off.
– ON
– OFF
ZOOM: Set zoom information on or off.
– ON
– OFF
P/T DEG: Set pan/tilt information on or off.
– ON
– OFF
BACK: Return to previous menu.
EXIT: Exit OSD menus.
DISPLAY SETUP
PRESET LABEL
ON
ZOOM
ON
P/T DEG
ON
BACK
EXIT
WINDOWS BLANKING Menu:
From MAIN MENU
This menus allows for setting the windows blanking or privacy window options.




WINDOW NUMBER: Select which privacy window to
set.
– 1~8
EDIT WINDOW LOCATION: Center the cursor over the
area to be blocked.
ENABLE WINDOW: Enable the selected privacy
window.
– OFF
– ON
CLEAR WINDOW: Clear the selected privacy window.
BACK: Return to previous menu.
EXIT: Exit OSD menus.
WINDOWS BLANKING
WINDOW NUMBER
1
EDIT WINDOW LOCATION
ENABLE WINDOW
OFF
CLEAR WINDOW
BACK
EXIT
EDIT WINDOW LOCATION
IRIS OPEN TO CONTINUE
W
340/42
X1
ALARMS SETTING Menu:
From MAIN MENU
This menu is reserved for future use.
28
SECO-LARM U.S.A., Inc.
ENFORCER Mini PTZ Camera
PRESET LABEL Menu:
From MAIN MENU
This menu allows for setting preset labels to be displayed on the main screen.



PRESET: Select which preset to name.
– 1~79
SET PRESET LABEL: Set the selected preset label.
CLEAR PRESET LABEL: Clear the selected preset
label.
BACK: Return to previous menu.
EXIT: Exit OSD menus.
PRESET LABEL
PRESET
1
SET PRESET LABEL
CLEAR PRESET LABEL
BACK
EXIT
PRESET LABEL
0123456789 YZ yz
ABCDEFGHIJKLMNOPQRSTUVWX
abcdefghijklmnopqrstuvwx
OK
SPACE
CANCEL
BACKSPACE
RESTORE FACTORY DEFAULT:
Restore all settings back to factory default (except for Camera sub-menu options).
REBOOT SYSTEM:
Reboot the camera and run through the start-up features.
EXIT:
Exit OSD menus.
SECO-LARM U.S.A., Inc.
29
ENFORCER Mini PTZ Camera
Preset Worksheet:
Preset #
Example: 1
30
Preset Scene (pan/tilt zoom)
Main office (19/57 x1)
SECO-LARM U.S.A., Inc.
ENFORCER Mini PTZ Camera
Installation Notes:
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
SECO-LARM U.S.A., Inc.
31
ENFORCER Mini PTZ Camera
Also Available from SECO-LARM:
Ceiling
Bracket
Pole-Mounting
Bracket
Corner-Mounting
Bracket
Flush-Mount
Bracket
DR-1 Series
Digital Video Recorder
EV-7100CEILM
EV-7100POLEM
EV-7100CORNM
EV-7100FLUSM
DR-116-1.0TQ
Data
Distributor
RS-232 to RS-485
Converter
Passive
Video Balun
Passive
Video/Power/Data Balun
AC Power
Supply
RD-304-D1Q
EVA-RS1
EB-P501-01Q
EB-P101-20VQ
EVP-1SA8P16UL
IMPORTANT: Users and installers of this product are responsible for ensuring that use of this product complies with all
national, state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM will not
be held responsible for the use of this product in violation of any current laws or statutes.
WARNING: Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or
electric shock. Do not open the case of this device, as there are no user-serviceable components inside.
FCC COMPLAINCE STATEMENT: Information to the user: This equipment has been tested and found to comply
with the limits for a class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the interference at his or her own
expense.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal
service for a period of three (3) years from the date of sale to the original consumer customer. SECO-LARM’s obligation is
limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect,
repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that
such equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential
personal or property damages of any kind to the purchaser or anyone else.
NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the
SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to
change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2014 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in
part, without the written permission of SECO-LARM.
SECO-LARM® U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Phone: (949) 261-2999 | (800) 662-0800
32
PISCN4
Website: www.seco-larm.com
MiEV-7605-NYWQ_1404.doc
Email: sales@seco-larm.com
SECO-LARM U.S.A., Inc.