OT Systems ET1111 Series Fast Ethernet Media Converter Quick Installation Guide

ET1111 series (short version)
Industrial Grade Microtype 10/100Base-TX to 100Base-FX Ethernet Media Converter
This quick start guide describes how to install and use the Industrial Media Converter. This is the Media Converter of
choice for harsh environments constrained by space.
Physical Description
The 100Base-FX connections, Terminal Block and Power Inputs
Model Number:
ET1111-X-MT
Top Panel
Top panel－The fiber port(s) for 100Base-FX connections
The 100Base-FX Connections
The TX (transmit) port of device I is connected to the RX (receive) port of device
II, and the RX (receive) port of device I to the TX (transmit) port of device II.
X value:
A for Multimode fiber
B for Singlemode fiber
FIBER
TX
RX
Connector
SC Optical Connector
SC Optical Connector
X value:
G for Multimode fiber
H for Singlemode fiber
FIBER
TX
RX
Connector
ST Optical Connector
ST Optical Connector
The WDM 100Base-FX Connections
Only one single-mode optical fiber is required to transmit and receive data.
X value:
C and D for Multimode fiber
H and F for Singlemode fiber
FIBER
Connector
SC Optical Connector
X value:
I and J for Multimode fiber
K and L for Singlemode fiber
FIBER
Bottom Panel
Connector
ST Optical Connector
Bottom panel－Ethernet Port and Power Input
Ethernet Port
RJ45 Connector
*There will be no “TX” and
NETWORK
“RX” in single fiber condition.
Power Input Assignment
12VDC
1
1 GND
2 12V
Terminal Block
V2.6
ET1111 series (short version)
Industrial Grade Microtype 10/100Base-TX to 100Base-FX Ethernet Media Converter
Interface
The 10/100Base-TX Connections
Pin
The following lists the pinouts of 10/100Base-TX ports.
Regular Ports
Uplink Port
1
Output Transmit Data +
Input Receive Data +
2
Output Transmit Data -
Input Receive Data -
3
Input Receive Data +
Output Transmit Data +
4
NC
NC
5
NC
NC
6
Input Receive Data -
Output Transmit Data -
7
NC
NC
8
NC
NC
.
The Port Status LEDs, dimension drawing for the Micro unit
LED
State
Indication
Green
Power on.
Off
Power off.
PWR
Green
100Base-FX
FX SPD
Off
Steady
FX LINK
Flashing
10Base-FX
A valid network connection established
Transmitting or receiving data.
ACT Stands for Activity.
Yellow
100Base-TX
Off
10Base-TX
SPD
Steady
A valid network connection established
Flashing
Transmitting or receiving data.
ACT Stands for Activity.
LINK/ACT
Functional Description
•
•
•
•
•
•
•
•
•
Converts 10/100Base-TX to 100Base-FX
Full/Half duplex, Auto-Negotiation
Singlemode or Multimode fiber operation
Single or Dual-core fiber with SC or ST connectors
MDI/MDI-X Auto-Crossover supported
Sleek Microtype design, fits within most camera housing
Plug-and-Play
12VDC Terminal Block Power inputs
-10°C to 60°C (14°F to 140°F) operating temperature.
Assembly, Startup, and Dismantling
Installation
• Installation: Mount the Micro-type unit onto a fixture, or camera housings, e.g. a plank, (either on the wall or on
a flat surface) with at least 2 screws piercing through the holes on the mounting frame to secure it in position.
• Startup: Connect the supply voltage to start up the Media Converter via the terminal block.
• Dismantling: Locate and remove the securing screws. Usually, but not limited to, at least 2 screws.
Manual Earth Green manual is available on our website www.ot-systems.com
2
V2.6