Allied Telesis AT-8624T/2M Installation And Safety Manual

Add to my manuals
38 Pages

advertisement

Allied Telesis AT-8624T/2M Installation And Safety Manual | Manualzz

A5 Installation and Safety Guide Cover

AT-8600 Series Switch

Installation and Safety Guide

AT-8624T/2M

AT-8624PoE

AT-8648T/2SP

AT-8600 Series

Installation & Safety Guide

AT-8624T/2M

AT-8624PoE

AT-8648T/2SP

2 AT-8600 Series Switch

AT-8600 Installation & Safety Guide

Document Number C613-000083 REV D.

© 2006 Allied Telesis Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis Inc.

Allied Telesis Inc. reserves the right to change specifications and other information in this document without prior written notice. The information provided herein is subject to change without notice. In no event shall Allied

Telesis Inc. be liable for any incidental, special, indirect, or consequential damages whatsoever, including but not limited to lost profits, arising out of or related to this manual or the information contained herein, even if Allied Telesis

Inc. has been advised of, known, or should have known, the possibility of such damages.

All company names, logos, and product designs that are trademarks or registered trademarks are the property of their respective owners.

Installation & Safety Guide

Electrical Safety and Emission Compliance Statement

3

STANDARDS: This product meets the following standards:

Category

Electromagnetic Compliance

Immunity

Approval Agency and Requirement

UL60950-1

CAN/CSA-C22.2 No. 60950-1-03

EN60950-1

EN60825-1

FCC CFR47 Part 15 Class A

EN55022 Class A

EN61000-3-2

EN61000-3-3

VCCI Class A

AS/NZS CISPR22 Class A

EN55024

U.S. Federal Communications Commission

RADIATED ENERGY

Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Canadian Department of Communications

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing

Equipment Regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

4 AT-8600 Series Switch

Electrical Safety

IMPORTANT: This equipment must be installed in accordance with safety precautions (page

20

).

Elektrische Sicherheit

WICHTIG: Für die Installation dieses Gerätes ist die Einhaltung von

Sicherheitsvorkehrungen erforderlich (Seite

21 ).

Elektrisk sikkerhed

VIGTIGT: Dette udstyr skal installeres i overensstemmelse med sikkerhedsadvarslerne (side

23

).

Elektrische veiligheid

BELANGRIJK: Dit apparaat moet in overeenstemming met de veiligheidsvoorschriften worden geïnstalleerd (pagina

24 ).

Sécurité électrique

IMPORTANT: Cet équipement doit être utilisé conformément aux instructions de sécurité (page

25

).

Sähköturvallisuus

TÄRKEÄÄ: Tämä laite on asennettava turvaohjeiden mukaisesti (sivu

26

).

Sicurezza elettrica

IMPORTANTE: questa apparecchiatura deve essere installata rispettando le norme di sicurezza (pagina

28 ).

Elektrisk sikkerhet

VIKTIG: Dette utstyret skal installeres i samsvar med sikkerhetsregler

(side 29

).

Segurança eléctrica

IMPORTANTE: Este equipamento tem que ser instalado segundo as medidas de precaução de segurança (página

30 ).

Seguridad eléctrica

IMPORTANTE: La instalación de este equipo deberá llevarse a cabo cumpliendo con las precauciones de seguridad (página

31 ).

Elsäkerhet

OBS! Alla nödvändiga försiktighetsåtgärder måste vidtas när denna utrustning används (sida

33

).

EC Declaration of Conformity

EC Declaration of Conformity (page

35 ).

Installation & Safety Guide

Table of Contents

Electrical Safety and Emission Compliance Statement ............................................. 3

Models Covered By This Guide .................................................................................... 6

Package Contents ............................................................................................................. 6

Selecting a Site ................................................................................................................... 7

How to Install the Switch ............................................................................................... 8

How to Configure the Switch ..................................................................................... 11

LEDs on AT-8600 Series Switches .............................................................................. 14

Documentation and Tools CD-ROM ......................................................................... 19

Safety ................................................................................................................................. 20

Sicherheit .......................................................................................................................... 21

Sikkerhed .......................................................................................................................... 23

Veiligheid ........................................................................................................................... 24

Sécurité ............................................................................................................................. 25

Turvallisuus ....................................................................................................................... 26

Norme di Sicurezza ........................................................................................................ 28

Sikkerhet ........................................................................................................................... 29

Segurança .......................................................................................................................... 30

Seguridad .......................................................................................................................... 31

Säkerhet ............................................................................................................................ 33

EC Declaration of Conformity .................................................................................... 35

5

6

Models Covered By This Guide

AT-8600 Series Switch

This Installation & Safety Guide includes information on these models:

■ AT-8624T/2M 24-port 10BASE-T/100BASE-TX Layer 3 Fast Ethernet

Switch

■ AT-8624PoE 24-port 10BASE-T/100BASE-TX Layer 3 Fast Ethernet Switch

■ AT-8648T/2SP 48-port 10BASE-T/100BASE-TX Layer 3 Fast Ethernet

Switch

You can download Installation & Safety Guide updates from http:// www.alliedtelesis.com/support.

Package Contents

These items are included with each AT-8600 Series switch:

■ One AC power cord

■ One power cord retaining clip

■ One serial cable for connecting the switch to a terminal or PC

■ One 19 inch rack-mount kit

■ One AT-8600 Series Installation & Safety Guide (which includes statutory and safety information)

■ One AT-8600 Series Documentation and Tools CD-ROM (which includes the complete AT-8600 Series document set and utilities)

■ One warranty card

Contact your authorised distributor or reseller if any items are damaged or missing.

Installation & Safety Guide

Selecting a Site

You can install the switch in a standard 19-inch rack, on a level surface such as a desktop or bench, or against a wall using the optional wall-mount kit. How to install the switch using the 19-inch rack-mount kit is described below. .

When you install the switch, choose a site that:

■ allows adequate airflow around the switch and its vents.

■ is free of dust and moisture.

■ will maintain an ambient temperature range of 0 º C to 40º C

(32º F to 104º F) and a humidity range of 5% to 80% non-condensing.

■ has a reliable and earthed (grounded) power supply, preferably dedicated and filtered.

■ does not expose cabling to sources of electrical noise such as radio transmitters, broadband amplifiers, power lines, electric motors, and fluorescent fixtures.

■ allows easy access to the switch’s power and cable connections.

■ allows all related network devices to be connected to the switch without exceeding maximum cable length limitations as specified in the AT-8600

Series Hardware Reference.

■ ensures that when the switch is mounted in a rack, the switch is mounted evenly to prevent uneven mechanical loading of the rack.

7

8 AT-8600 Series Switch

How to Install the Switch

Warning All versions of this equipment must be earthed.

Prepare to install the switch

1.

Read the safety information

Read the safety information included in this Installation & Safety Guide. This

Installation & Safety Guide is also on the Documentation and Tools CD-ROM and you can download a copy from

http:// www.alliedtelesis.com

.

2.

Gather the tools and equipment you will need

You will need a Phillips #2 flat-head screwdriver and cage nuts to attach the brackets to your rack. These are not supplied.

3.

Choose a suitable operating location

Follow the guidelines described in “Selecting a Site” on page 7

to choose a suitable location.

You can install the switch either in a 19-inch rack, on a flat bench, or against a wall.

4.

Unpack the switch

Verify the package contents. If any items are damaged or missing, contact your authorised distributor or reseller.

5.

Install expansion modules (optional)

The only expansion module supported by the AT-8624T/2M is the AT-A46.

If you purchased expansion modules, install them now by following the instructions in the AT-A45/xx Series, AT-A46, and AT-A47 Expansion Modules

Installation Guide that comes with the modules. The AT-A46 expansion module is supported by AT-8000 Series switches as well as AT-8600 Series switches.

Hot swap of expansion modules is not supported on AT-8624T/2M switches. If you insert or remove a module when the switch is already powered on, you must restart the switch before the module can be used.

6.

Place the switch in its operating location

If installing the switch in a rack:

• Remove the rubber feet on the bottom of the switch with a flat-head screwdriver.

• Attach the two rack-mounting brackets to the switch with the screws provided in the rack-mount kit.

Installation & Safety Guide

• Mount the switch in the rack using standard screws (these are not provided).

9

7.

Install SFPs

For the AT-8648T/2SP, you may also need an optional SFP (Small Formfactor Pluggable module).

Do not look into the optical ports of SFP cables or transceivers. Invisible laser radiation may be emitted from disconnected fibres or connectors.

The SFP transceivers must be inserted the right way into the SFP 49 or SPF

50 slots. See the figure below.

Slide the transceiver into the SFP socket, and firmly press it until it engages.

To remove it, first release it by gently pulling the release lever, and then pull it out of the socket. Never force a transceiver into or out of a socket.

When an SFP is installed into one of the two SFP ports, that SFP port takes precedence over its corresponding 10/100/1000T port. When the SFP is removed, the 10/100/1000T port is once again active.

8.

Check the supply voltage and the switch’s rated voltage

AT-8600 Series switches are fitted with a universal main power supply that will function over the range 100–240 VAC and 50–60 Hz.

The specific power supply requirements for a particular model are clearly displayed on the rear or underside of the switch. If the supply is outside the accepted range for the switch, the switch may not operate or damage to the switch may result.

10 AT-8600 Series Switch

9.

Apply AC power to the switch

Plug the power cord into the AC power connector. This is on the switch’s rear panel, as shown in the below figures.

Figure 1: AT-8624T/2M front and rear panel with AC power inlet.

25 26

1 3 5 7 9 11

2 4 6 8 10 12

13 15 17 19 21 23

14 16 18 20 22 24

AT-8624T/2M

Layer 3 Fast Ethernet Switch

LINK

MODE

LINK

MODE

1

2

3

4

5 7 9 11 13 15 17 19 21 23

6 8 10 12 14 16 18 20 22 24

MODE

COL

100

FULL

ACT

RS-232

TERMINAL PORT

STATUS

FAULT

MASTER

RPS

PWR

Figure 2: AT-8624PoE front and rear panel with AC power inlet

25 26

1 3 5 7 9 11

2 4 6 8 10 12

13 15 17 19 21 23

14 16 18 20 22 24

100 LINK

FULL DUP

1

PD ON

3 5

ACT

7

10 LINK

HALF DUP

PD ERR

9 11

ACT

COL

MAX CURRENT

13 15 17 19 21 23

MODE

AT-8624POE

Layer 3 Fast Ethernet Switch

RS-232

TERMINAL PORT

STATUS

FAULT

MASTER

RPS

PWR

2 4 6 8 10 12 14 16 18 20 22 24

Figure 3: AT-8648T/2SP front and rear panel with AC power inlet

49

LINK

LINK 49R MODE

SFP

50

LINK

LINK 50R MODE

CLASS 1

LASER PRODUCT

DO NOT STARE

INTO BEAM

AT-8648T/2SP

Layer 3 Fast Ethernet Switch

STATUS

COL

SPD

FDX

ACT

MODE

FLT

MSTR

RPS

PWR

10. Check that the PWR LED on the switch’s front panel lights green

If the PWR (power) LED fails to light, refer to the AT-8600 Series Hardware

Reference for troubleshooting information.

11. Connect the data cables

Make sure each cable connection is secure. The switch will now perform basic Layer 2 switching functions.

Installation & Safety Guide

How to Configure the Switch

11

Some configuration is necessary to enable the switch’s advanced switching capabilities. This is achieved via the Command Line Interface (CLI). On the

AT-8624T/2M, you can also use the Graphical User Interface (GUI).

Using the CLI to configure a switch

1.

Connect a terminal or PC to the Terminal Port (ASYN0).

Using the supplied RS-232 DB9 serial straight-through cable, connect your terminal or PC to the RS-232 Terminal Port:

• For the AT-8624T/2M and AT-8624PoE, the RS-232 Terminal Port is on the front panel.

• For the AT-8648T/2SP, the RS-232 Terminal Port is on the back panel.

2.

Set the communication parameters.

Set the communication parameters on your terminal or terminal emulation program to:

• Bit rate: 9600

• Data bits: 8

• Parity: None

• Stop bits: 1

• Flow control: None

3.

Log in.

After the switch has booted, the login prompt appears. If the login prompt does not appear, press [Enter] two or three times.

When the switch boots for the first time it automatically creates an account with manager privileges. The account has the login name manager and the password is friend.

At the login prompt, enter the login name and password:

Login: manager

Password: friend

The switch’s command prompt appears. Now use the CLI to configure the switch.

12 AT-8600 Series Switch

4.

Change password and display help.

Change the password as soon as possible because a manager account left with the default password is a serious security risk. Remember the new password as there is no way to retrieve it if it is lost.

To change the account password, use the command: set password

To display a list of help topics, use the command: help

To display help on a specific topic, use the command: help topic

Alternatively, type a question mark (?) at the end of a partially completed command to see a list of valid options.

How to configure the switch is explained in detail in the AT-8600 Series Software

Reference.

Using the GUI to configure the

AT-8624T/2M

switch

This section describes how to establish a connection to the AT-8624T/2M switch through the GUI so you can configure it before installing it in your LAN.

1.

Select a PC to use and identify its subnet.

You can browse to the switch from any PC that is running a supported operating system with a supported browser installed. JavaScript must be enabled. If you are using a toolbar or plug-in on your browser to block popups, disable it while using the GUI. The GUI displays detailed configuration options and information in pop-up windows.

2.

Connect the PC to the

switch.

Use an Ethernet cable to connect an Ethernet card on the PC to any one of the switch ports.

You can browse to the router through any VLAN, as long as you give that

VLAN an IP address. These instructions assume you are using vlan1. All switch ports belong to vlan1 by default.

3.

Access the

switch

’s command line interface.

Access the CLI from the PC, as described in the previous section, “Using the CLI to configure a switch”.

Installation & Safety Guide

4.

Enable IP.

enable ip

13

5.

Assign the vlan1 interface an IP address in the same subnet as the

PC.

add ip interface=vlan1 ip=ipaddress mask=mask

6.

Save the configuration and set the

switch

to use it on bootup.

create config=your-name.cfg

set config=your-name.cfg

7.

On the PC’s web browser, bypass the HTTP proxy server, if necessary.

8.

Point your web browser at IP address for vlan1.

9.

At the login prompt, enter the user name and password.

User Name: manager <the default>

Password: friend

The System Status page is displayed. Select options from the sidebar menu to configure and manage the switch.

For context-sensitive online help, click the Help button at the top of the sidebar menu or on any pop-up page.

14 AT-8600 Series Switch

LEDs on AT-8600 Series Switches

The following tables outline how the switch and expansion modules report faults and operational activities. Expansion modules are optional and can be purchased separately. Contact an authorised Allied Telesis distributer or reseller, or visit www.alliedtelesis.com for more information on purchasing expansion modules.

System LEDs

LED

FAULT

State

Off

Red

Description

Switch operation is normal.

The switch or management software is malfunctioning.

A switch fan has failed.

PWR

1 flash

3 flashes

4 flashes

5 flashes

Green

Off

The main PSU has failed and the RPS is now providing power.

The RPS Monitor is set to ON, and the RPS is not functioning, either because it has failed or has been switched off.

The RPS Monitor is set to ON, but the RPS is not connected.

7 flashes For the AT-8624T/2M and AT-8624PoE switches: An expansion module has been inserted or removed while the switch is powered on.

MASTER This LED is not supported and will never be lit.

RPS Green An optional redundant power supply is connected to the switch.

OFF There is no optional redundant power supply connected to the switch.

The switch is receiving power and the voltage is within the acceptable range.

The switch is not receiving power.

Note Use the Mode Select button to toggle the Mode LEDs to the desired state.

Toggling the Mode Selection button does not affect the normal operations of the switch.

Installation & Safety Guide 15

Link and Mode LEDs for the AT-8624T/2M switch

LED

LINK

Mode - COL

Mode - 100

Flashing Green

OFF

Green

Mode - FULL OFF

Mode - ACT

State

OFF

Green

OFF

Green

OFF

Flashing Green

Description

There is no link between the port and the end-node.

A valid link has been established between the port and the end-node.

No data collisions are occurring on the port.

Data collisions are occurring on the port.

The port is operating at 10 Mbps.

The port is operating at 100 Mbps.

The port is operating in half-duplex mode.

The port is operating in full-duplex mode.

There is no activity on the port.

There is activity on the port. It is transmitting and/or receiving data.

16 AT-8600 Series Switch

Link and Mode LEDs for the AT-8624PoE switch

LED

L/A Status

(Top LED)

State

OFF

Green

Flashing Green There is activity on the port. It is transmitting and/or receiving data at 100 Mbps.

Red

Flashing Red

The port is operating at 10 Mbps.

OFF

Description

There is no link between the port and the end-node.

The port is operating at 100 Mbps.

There is activity on the port. It is transmitting and/or receiving data at 10 Mbps.

Either DC Mode or PoE Mode.

Mode LEDs

(Bottom LED)

D/C Mode

OFF

PoE Mode

Green

Red

Flashing Red

OFF

Green

Red

Flashing Red

There is no link between the port and the end-node.

The port is operating in full duplex mode.

The port is operating in half-duplex mode.

The port is operating in half-duplex mode and data collisions are occurring on the port.

There is no powered device detected.

The end-node is a powered device and the port is providing power to it.

The port is experiencing a problem providing PoE to the end-node.

The port is connected to a powered device but providing power to it would exceed the maximum PoE power budget of the switch.

Installation & Safety Guide 17

Link and Mode LEDs for the AT-8648T/2SP switch

LED

LINK

Mode - COL

Mode - SPD

Mode - FDX

Mode - ACT

State

OFF

Green

Description

There is no link between the port and the end-node.

A valid link has been established between the port and the endnode.

OFF No data collisions are occurring on the port.

Flashing Green Data collisions are occurring on the port.

OFF

Green

OFF

The port is operating at 10 Mbps.

The port is operating at 100 Mbps.

Green

The port is operating in half-duplex mode.

The port is operating in full-duplex mode.

OFF There is no activity on the port

Flashing Green There is activity on the port.

18 AT-8600 Series Switch

SFP and 10/100/1000Base-T LEDs for the AT-8648T/2SP switch

LED

LINK

Mode - COL

Mode - SPD

Mode - FDX

Mode - ACT

State

OFF

Green

Description

There is no link between the port and the end-node.

A valid link has been established between the port and the endnode.

OFF No data collisions are occurring on the port.

Flashing Green Data collisions are occurring on the port.

OFF The port is operating at 10/100

Mbps.

Green

OFF

The port is operating at 1000

Mbps.

The port is operating in half-duplex mode.

Green The port is operating in full-duplex mode.

OFF There is no activity on the port

Flashing Green There is activity on the port.

Installation & Safety Guide

Documentation and Tools CD-ROM

19

The Documentation and Tools CD-ROM bundled with each switch contains the complete documentation set for AT-8600 Series switches and their expansion options, as well as tools to manage the switch.

The documentation and tools CD-ROM includes:

■ This Installation & Safety Guide, which also provides safety and statutory information for the AT-8600 Series switch and its expansion options.

■ The AT-8600 Series Hardware Reference, which provides detailed information on the switch unit and its hardware features.

■ The AT-8600 Series Software Reference, which provides detailed information on configuring the switch unit and its software.

■ The AT-A45/xx Series, AT-A46, and AT-A47 Expansion Modules Installation Guide, which outlines the procedure for installing expansion modules, and provides technical specifications for the modules.

■ AT-TFTP Server for Windows for downloading software releases.

■ How To notes, white papers, Visio Stencils, and information about related

Allied Telesis products.

■ MIBs supported by the switch

■ Adobe Acrobat Reader for viewing online documentation.

20 AT-8600 Series Switch

Safety

WARNING: In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

WARNING: Class 1 Laser product.

WARNING: Do not stare into the laser beam.

CAUTION: Use of controls or adjustments of performance or procedures other than those specified herein may result in hazardous radiation exposure.

ELECTRICAL NOTICES

WARNING: ELECTRIC SHOCK HAZARD

To prevent ELECTRIC shock, do not remove the cover. No user-serviceable parts inside. This unit contains HAZARDOUS VOLTAGES and should only be opened by a trained and qualified technician.

LIGHTNING DANGER

DANGER: DO NOT WORK on equipment or CABLES during periods of

LIGHTNING ACTIVITY.

CAUTION: POWER CORD IS USED AS A DISCONNECTION DEVICE. TO

DE-ENERGIZE EQUIPMENT, disconnect the power cord.

ELECTRICAL - TYPE CLASS 1 EQUIPMENT

THIS EQUIPMENT MUST BE EARTHED. Power plug must be connected to a properly wired earth ground socket outlet. An improperly wired socket outlet could place hazardous voltages on accessible metal parts.

PLUGGABLE EQUIPMENT, the socket outlet shall be installed near the equipment and shall be easily accessible.

CAUTION: Air vents must not be blocked and must have free access to the room ambient air for cooling.

OPERATING TEMPERATURE: This product is designed for a maximum ambient temperature of 40 degrees C.

ELECTRICAL - AC MAINS CIRCUIT OVERLOADING

When installing product, consideration must be given to the accumulative nameplate ratings when connecting the equipment to the AC supply wiring.

CAUTION: MECHANICAL LOADING - Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven loading.

Installation & Safety Guide

Lithium Battery - Should only be changed by authorised service personnel.

CAUTION: Danger of explosion if battery incorrectly replaced. Replace only with Lithium Battery, type CR2032, and dispose of in accordance with the manufacturer’s recommendations and all local codes.

21

ALL COUNTRIES: Install product in accordance with local and National

Electrical Codes.

WARNING: Only trained and qualified personnel are allowed to install or replace this equipment.

CAUTION: This unit does not contain serviceable components. Please return damaged units for servicing.

CAUTION: The AT-8624PoE Ethernet ports are only intended for installation in

Environment A as defined in IEEE 802.3af. All interconnected equipment must be contained in the same building including the interconnected equipment’s associated LAN connections.

CAUTION: The surface-mount fuses F1 to F24 on the Power over Ethernet daughterboard in the AT-8624PoE switch are 60V, max 2A fuses. These fuses are not field-replaceable, and should only be serviced by a trained Allied Telesis service technician.

Sicherheit

WARNUNG: Bei Verwendung zu Hause kann dieses Produkt Funkstörungen hervorrufen. In diesem Fall müßte der Anwender angemessene

Gegenmaßnahmen ergreifen.

WARNUNG Laserprodukt der Klasse 1.

WARNUNG Nicht direkt in den Strahl blicken.

ACHTUNG: GEFÄHRLICHE SPANNUNG

Das Gehäuse nicht öffnen. Das Gerät enthält keine vom Benutzer wartbaren

Teile. Das Gerät steht unter Hochspannung und darf nur von qualifiziertem technischem Personal geöffnet werden.

GEFAHR DURCH BLITZSCHLAG

GEFAHR: Keine Arbeiten am Gerät oder an den Kabeln während eines

Gewitters ausführen.

22 AT-8600 Series Switch

VORSICHT: DAS NETZKABEL DIENT ZUM TRENNEN DER

STROMVERSORGUNG. ZUR TRENNUNG VOM NETZ, KABEL AUS DER

STECKDOSE ZIEHEN.

GERÄTE DER KLASSE 1

DIESE GERÄTE MÜSSEN GEERDET SEIN. Der Netzstecker darf nur mit einer vorschriftsmäßig geerdeten Steckdose verbunden werden. Ein unvorschriftsmäßiger Anschluß kann die Metallteile des Gehauses unter gefährliche elektrische Spannungen setzen.

STECKBARES GERÄT: Die Anschlußbuchse sollte in der Nähe der Einrichtung angebracht werden und leicht zugänglich sein.”

VORSICHT

Die Entlüftungsöffnungen dürfen nicht versperrt sein und müssen zum Kühlen freien Zugang zur Raumluft haben.

BETRIEBSTEMPERATUR: Dieses Produkt wurde für den Betrieb in einer

Umgebungstemperatur von nicht mehr als 40° C entworfen.

NETZSICHERUNG

Bei der Installation muß der auf dem Typenschild angezeigte Nennwert des

Gerätes für den Anschluß an das Netz beachtet werden.

VORSICHT: RAHMENEINBAU

Die Geräte müssen so in den Rahmen montiert werden, daß keine Gefahren durch unebenen inbau des Rahmens verursacht werden.

Lithium-Batterie - Sollte nur von einem geschulten qualifizierten Techniker ausgetauscht werden.

VORSICHT: Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Nur mit einer gleichen Batterie oder einem gleichwertigen Batterietyp nach

Empfehlung des Herstellers ersetzen. Gebrauchte Batterien nach Anweisungen des Herstellers beseitigen.

ALLE LÄNDER: Installation muß örtlichen und nationalen elektrischen

Vorschriften entsprechen.

Maschinenlärminformations-Verordnung - 3. GPSGV, der höchste

Schalldruckpegel beträgt 70dB(A) oder weniger gemäss EN ISO 7779

Installation & Safety Guide

Sikkerhed

23

ADVARSEL: I et hjemligt miljø kunne dette produkt forårsage radio forstyrrelse.

Bliver det tilfældet, påkræves brugeren muligvis at tage tilstrækkelige foranstaltninger.

ADVARSEL Laserprodukt av klasse 1.

ADVARSEL Stirr ikke på strålen.

ELEKTRISKE FORHOLDSREGLER

ADVARSEL: RISIKO FOR ELEKTRISK STØD

For at forebygge ELEKTRISK stød, undlad at åbne apparatet. Der er ingen indre dele, der kan repareres af brugeren. Denne enhed indeholder LIVSFARLIGE

STRØMSPÆNDINGER og bør kun åbnes af en uddannet og kvalificeret tekniker.

FARE UNDER UVEJR

FARE: UNDLAD at arbejde på udstyr eller KABLER i perioder med

LYNAKTIVITET.

ADVARSEL: DEN STRØMFØRENDE LEDNING BRUGES TIL AT AFBRYDE

STRØMMEN. SKAL STRØMMEN TIL APPARATET AFBRYDES, tages ledningen ud af stikket.

ELEKTRISK - KLASSE 1-UDSTYR

DETTE UDSTYR KRÆVER JORDFORBINDELSE. Stikket skal være forbundet med en korrekt installeret jordforbunden stikkontakt. En ukorrekt installeret stikkontakt kan sætte livsfarlig spænding til tilgængelige metaldele.

UDSTYR TIL STIKKONTAKT, stikkontakten bør installeres nær ved udstyret og skal være lettilgængelig.

ADVARSEL: Ventilationsåbninger må ikke blokeres og skal have fri adgang til den omgivende luft i rummet for afkøling.

BETJENINGSTEMPERATUR: Dette apparat er konstrueret til en omgivende temperatur på maksimum 40 grader C.

ELEKTRISK-OVERBELASTNING AF SPÆNDINGSKREDSLØBET

Ved installation af produktet, bør der tages hensyn til den kumulative kapacitet der angives på navneskiltet, når udstyret forbindes med vekselstrømsledningen.

ADVARSEL: MEKANISK OPSTILLING-Udstyret skal opstilles i stativet, på en sådan måde, at der kke opstår fare p.g.a. ujævn opstilling.

24 AT-8600 Series Switch

Lithium batteri - Bør kun udskiftes af uddannet og kvalificeret tekniker.

ADVARSEL : Eksplosionsfare, hvis batteriet udskiftes ukorrekt. Udskift kun med samme eller en tilsvarende type der anbefales af producenten. Kassér brugte batterier i overensstemmelse med producentens instruktioner.

ALLE LANDE: Installation af produktet skal ske i overensstemmelse med lokal og national lovgivning for elektriske installationer.

Veiligheid

WAARSCHUWING: Binnenshuis kan dit product radiostoring veroorzaken, in welk geval de gebruiker verplicht kan worden om gepaste maatregelen te nemen.

WAARSHUWING Klasse-1 laser produkt.

WAARCHUWING Neit in de straal staren.

WAARSCHUWINGEN MET BETREKKING TOT ELEKTRICITEIT

WAARSCHUWING: GEVAAR VOOR ELEKTRISCHE SCHOKKEN

Verwijder het deksel niet, teneinde ELEKTRISCHE schokken te voorkomen.

Binnenin bevinden zich geen onderdelen die door de gebruiker onderhouden kunnen worden. Dit toestel staat onder GEVAARLIJKE SPANNING en mag alleen worden geopend door een daartoe opgeleide en bevoegde technicus.

GEVAAR VOOR BLIKSEMINSLAG

GEVAAR: NIET aan toestellen of KABELS WERKEN bij BLIKSEM.

WAARSCHUWING: HET TOESTEL WORDT UITGESCHAKELD DOOR DE

STROOMKABEL TE ONTKOPPELEN.OM HET TOESTEL STROOMLOOS TE

MAKEN: de stroomkabel ontkoppelen.

ELEKTRISCHE TOESTELLEN VAN KLASSE 1

DIT TOESTEL MOET GEAARD WORDEN. De stekker moet aangesloten zijn op een juist geaarde contactdoos. Een onjuist geaarde contactdoos kan de metalen onderdelen waarmee de gebruiker eventueel in aanraking komt onder gevaarlijke spanning stellen.

AAN TE SLUITEN APPARATUUR, de contactdoos wordt in de nabijheid van de apparatuur geïnstalleerd en is gemakkelijk te bereiken.”

OPGELET: De ventilatiegaten mogen niet worden gesperd en moeten de omgevingslucht ongehinderd toelaten voor afkoeling.

Installation & Safety Guide 25

BEDRIJFSTEMPERATUUR: De omgevingstemperatuur voor dit produkt mag niet meer bedragen dan 40 graden Celsius.

ELEKTRISCH: OVERBELASTING VAN WISSELSTROOM HOOFDCIRCUIT

Tijdens de installatie van het produkt dient men rekening te houden met de gecombineerde waarden op de naamplaatjes bij het aansluiten van het toestel op de wisselstroom-voedingsdraden.

LOPGELET: MECHANISCH LADEN - De montage van het toestel in het rek dient zo uitgevoerd te worden dat geen gevaar ontstaat door een ongelijke lading.

Lithium batterij. Mag alleen worden vervangen door een daartoe opgeleide en bevoegde technicus.

OPGELET: Gevaar voor ontploffing indien de batterij verkeerd wordt vergangen.

Alleen vervangen door hetzelfde of een gelijkwaardig, door de fabrikant aanbevolen type.

ALLE LANDEN: het toestel installeren overeenkomstig de lokale en nationale elektrische voorschriften.

Sécurité

MISE EN GARDE : dans un environnement domestique, ce produit peut provoquer des interférences radioélectriques. Auquel cas, l’utilisateur devra prendre les mesures adéquates.

ATTENTION Producit laser di classe 1.

ATTENTION Ne pas fixer le faisceau des yeux.

INFORMATION SUR LES RISQUES ÉLECTRIQUES

AVERTISSEMENT: DANGER D’ÉLECTROCUTION

Pour éviter toute ÉLECTROCUTION, ne pas ôter le revêtement protecteur du matériel. Ce matériel ne contient aucun élément réparable par l’utilisateur. Il comprend des TENSIONS DANGEREUSES et ne doit être ouvert que par un technicien dûment qualifié.

DANGER DE FOUDRE

DANGER: NE PAS MANIER le matériel ou les CÂBLES lors d’activité orageuse.

ATTENTION: LE CORDON D’ALIMENTATION SERT DE MISE HORS

CIRCUIT. POUR COUPER L’ALIMENTATION DU MATÉRIEL, débrancher le cordon.

26 AT-8600 Series Switch

ÉQUIPEMENT DE CLASSE 1 ÉLECTRIQUE

CE MATÉRIEL DOIT ÊTRE MIS A LA TERRE. La prise de courant doit être branchée dans une prise femelle correctement mise à la terre car des tensions dangereuses risqueraient d’atteindre les pièces métalliques accessibles à l’utilisateur.

EQUIPEMENT POUR BRANCHEMENT ELECTRIQUE, la prise de sortie doit

être placée près de l’équipement et facilement accessible”.

ATTENTION: Ne pas bloquer les fentes d’aération, ceci empêcherait l’air ambiant de circuler librement pour le refroidissement.

TEMPÉRATURE DE FONCTIONNEMENT: Ce matériel est capable de tolérer une température ambiante maximum de ou 40 degrés Celsius.

SURCHARGE DES CIRCUITS PRINCIPAUX DE COURANT ALTERNATIF

ÉLECTRIQUE

Lors de l'installation du matériel, il faut prendre en compte la somme des puissances indiquées sur les étiquettes au moment de connecter le matériel à une source de courant alternatif.

ATTENTION : RÉPARTITION DE LA CHARGE MÉCANIQUE - Le montage du matériel dans le bâti doit être effectué de telle manière que la répartition de la charge mécanique ne pose aucun danger.

Pile en Lithium-Doit uniquement être remplacée par un technicien dûment qualifié

ATTENTION : Un danger d'explosion existe en cas de remplacement incorrect de la pile. Remplacer uniquement avec une pile du même type ou d'un type recommandé par le fabricant. Mettre au rebut lespiles usagées conformément aux instructions du fabricant).

POUR TOUS PAYS: Installer le matériel conformément aux normes électriques nationales et locales.

Turvallisuus

VAROITUS: Kotiolosuhteissa tämä laite voi aiheuttaa radioaaltojen häiröitä, missä tapauksessa laitteen käyttäjän on mahdollisesti ryhdyttävä tarpeellisiin toimenpiteisiin.

VAROITUS Luokan 1 Lasertuote.

VAROITUS Älä katso säteeseen.

Installation & Safety Guide 27

SÄHKÖÖN LIITTYVIÄ HUOMAUTUKSIA

VAROITUS: SÄHKÖISKUVAARA

Estääksesi SÄHKÖISKUN älä poista kantta. Sisällä ei ole käyttäjän huollettavissa olevia osia. Tämä laite sisältää VAARALLISIA JÄNNITTEITÄ ja sen voi avata vain koulutettu ja pätevä teknikko.

SALAMANISKUVAARA

HENGENVAARA: ÄLÄ TYÖSKENTELE laitteiden tai KAAPELEIDEN KANSSA

SALAMOINNIN AIKANA.

HUOMAUTUS: VIRTAJOHTOA KÄYTETÄÄN

VIRRANKATKAISULAITTEENA. VIRTA KATKAISTAAN irrottamalla virtajohto.

SÄHKÖ - TYYPPILUOKAN 1 LAITTEET

TÄMÄ LAITE TÄYTYY MAADOITTAA. Pistoke täytyy liittää kunnollisesti maadoitettuun pistorasiaan. Virheellisesti johdotettu pistorasia voi altistaa metalliosat vaarallisille jännitteille.

PISTORASIAAN KYTKETTÄVÄ LAITE; pistorasia on asennettava laitteen lähelle ja siihen on oltava esteetön pääsy.”

HUOMAUTUS: Ilmavaihtoreikiä ei pidä tukkia ja niillä täytyy olla vapaa yhteys ympäröivään huoneilmaan, jotta ilmanvaihto tapahtuisi.

KÄYTTÖLÄMPÖTILA: Tämä tuote on suunniteltu ympäröivän ilman maksimilämpötilalle 40°C.

SÄHKÖ-VAIHTORVIRTASÄHKÖPIIRIN YLIKUORMITUS

Tuotetta asennettaessa on otettava huomioon osien nimikilvissä osoitettu teho silloin kun osat liitetetään vaihtovirtaverkkoon.

HUOMAUTUS: MEKAANINEN KUORMITUS--Osien asennuksen alustaan tulee tapahtua siten, että epätasainen kuormitus ei aiheuta vaaraa.

Litiumparisto - Vaihdon voi suorittaa vain koulutettu ja pätevä teknikko.

Varoitus: Räjähdysvaara, jos paristo on vaihdettu väärin. Vaihda vain samaan tai vastaavaan tyyppiin, jota valmistaja suosittelee. Hävitä käytetyt paristot valmistajan ohjeiden mukaan.

KAIKKI MAAT: Asenna tuote paikallisten ja kansallisten sähköturvallisuusmääräysten mukaisesti.

28 AT-8600 Series Switch

Norme di Sicurezza

AVVERTENZA: in ambiente domestico questo prodotto potrebbe causare radio interferenza. In questo caso potrebbe richiedersi all’utente di prendere gli adeguati provvedimenti.

AVVERTENZA Prodotto laser di Classe 1.

AVERTENZA Non fissare il raggio con gli occhi.

AVVERTENZE ELETTRICHE

ATTENZIONE: PERICOLO DI SCOSSE ELETTRICHE

Per evitare SCOSSE ELETTRICHE non asportare il coperchio. Le componenti interne non sono riparabili dall’utente. Questa unità ha TENSIONI

PERICOLOSE e va aperta solamente da un tecnico specializzato e qualificato.

PERICOLO DI FULMINI

PERICOLO: NON LAVORARE sul dispositivo o sui CAVI durante

PRECIPITAZIONI TEMPORALESCHE.

ATTENZIONE: IL CAVO DI ALIMENTAZIONE È USATO COME

DISPOSITIVO DI DISATTIVAZIONE. PER TOGLIERE LA CORRENTE AL

DISPOSITIVO staccare il cavo di alimentazione.

ELETTRICITÀ - DISPOSITIVI DI CLASSE 1

QUESTO DISPOSITIVO DEVE AVERE LA MESSA A TERRA. La spina deve essere inserita in una presa di corrente specificamente dotata di messa a terra.

Una presa non cablata in maniera corretta rischia di scaricare una tensione pericolosa su parti metalliche accessibili.

APPARECCHIATURA COLLEGABILE, la presa va installata vicino all’apparecchio per risultare facilmente accessibile”.

ATTENZIONE: le prese d’aria non vanno ostruite e devono consentire il libero ricircolo dell’aria ambiente per il raffreddamento.

TEMPERATURA DI FUNZIONAMENTO: Questo prodotto è concepito per una temperatura ambientale massima di 40 gradi centigradi.

ELETTRICITÀ - SOVRACCARICO DEL CIRCUITO DI RETE A C.A.

Durante l'installazione ed il collegamento del dispositivo alla rete di alimentazione a corrente alternata, è necessario tenere in considerazione le capacità cumulative riportate sulla targhetta.

Installation & Safety Guide 29

ATTENZIONE: CARICAMENTO MECCANICO - Il montaggio del dispositivo sul supporto va effettuato in maniera tale da evitare qualsiasi potenziale condizione di pericolo eventualmente dovuta al montaggio irregolare.

Batteria al litio - Va sostituita solo da un tecnico specializzato e qualificato.

ATTENZIONE: l'errata sostituzione della batteria può causare pericolo di esplosioni. Sostituire solamente con lo stesso tipo o con uno equivalente raccomandato dal produttore. Eliminare le batterie usate secondo le istruzioni del produttore.

TUTTI I PAESI: installare il prodotto in conformità delle vigenti normative elettriche nazionali.

Sikkerhet

ADVARSEL: Hvis dette produktet benyttes til privat bruk, kan produktet forårsake radioforstyrrelse. Hvis dette skjer, må brukeren ta de nødvendige forholdsregler.

ADVARSEL Laserprodukt av klasse 1.

ADVARSAL Stirr ikke på strålen.

ELEKTRISITET

ADVARSEL: FARE FOR ELEKTRISK SJOKK

For å unngå ELEKTRISK sjokk, må dekslet ikke tas av. Det finnes ingen deler som brukeren kan reparere på innsiden. Denne enheten inneholder FARLIGE

SPENNINGER, og må kun åpnes av en faglig kvalifisert tekniker.

FARE FOR LYNNEDSLAG

FARE: ARBEID IKKE på utstyr eller KABLER i TORDENVÆR.

FORSIKTIG: STRØMLEDNINGEN BRUKES TIL Å FRAKOBLE UTSTYRET. FOR

Å DEAKTIVISERE UTSTYRET, må strømforsyningen kobles fra.

ELEKTRISK - TYPE 1- KLASSE UTSTYR

DETTE UTSTYRET MÅ JORDES. Strømkontakten må være tilkoplet en korrekt jordet kontakt. En kontakt som ikke er korrekt jordet kan føre til farlig spenninger i lett t ilgjengelige metalldeler.

UTSTYR FOR STIKKONTAKT. Stikkontakten skal monteres i nærheten av utstyret og skal være lett tilgjengelig.”

30 AT-8600 Series Switch

FORSIKTIG: Lufteventilene må ikke blokkeres, og må ha fri tilgang til luft med romtemperatur for avkjøling.

DRIFTSTEMPERATUR: Dette produktet er konstruert for bruk i maksimum romtemperatur på 40 grader celsius.

ELEKTRISK OVERBELASTNING PÅ AC HOVEDKRETSLØP

Når produktet installeres, må de samlede navneplateverdiene kontrolleres nøye når strøm påsettes.

FORSIKTIG: MEKANISK LASTNING Installering av utstyret på hyllen må utføres på en slik måte at ingen farlige situasjoner oppstår som en følge av ujevn lastning.

Litiumbatteri — Må kun byttes ut av en faglig kvalifisert tekniker.

FORSIKTIG: Eksplosjonsfare hvis batteriet feilinnsettes.Batteriet må bare erstattes med samme type eller en tilsvarende type som er anbefalt av fabrikanten. Batteriene må kasseres i samsvar med fabrikantens instruksjoner.

ALLE LAND: Produktet må installeres i samsvar med de lokale og nasjonale elektriske koder.

Segurança

AVISO: Num ambiente doméstico este produto pode causar interferência na radiorrecepção e, neste caso, pode ser necessário que o utente tome as medidas adequadas.

AVISO Produto laser de classe 1

AVISO Não olhe fixamente para o raio.

AVISOS SOBRE CARACTERÍSTICAS ELÉTRICAS

ATENÇÃO: PERIGO DE CHOQUE ELÉTRICO

Para evitar CHOQUE ELÉTRICO, não retire a tampa. Não contém peças que possam ser consertadas pelo usuário. Este aparelho contém VOLTAGENS

PERIGOSAS e só deve ser aberto por um técnico qualificado e treinado.

PERIGO DE CHOQUE CAUSADO POR RAIO

PERIGO: NÃO TRABALHE no equipamento ou nos CABOS durante períodos suscetíveis a QUEDAS DE RAIO.

CUIDADO: O CABO DE ALIMENTAÇÃO É UTILIZADO COMO UM

DISPOSITIVO DE DESCONEXÃO. PARA DESELETRIFICAR O

EQUIPAMENTO, desconecte o cabo de ALIMENTAÇÃO.

Installation & Safety Guide 31

ELÉTRICO - EQUIPAMENTOS DO TIPO CLASSE 1

DEVE SER FEITA LIGAÇÃO DE FIO TERRA PARA ESTE EQUIPAMENTO. O plugue de alimentação deve ser conectado a uma tomada com adequada ligação de fio terra. Tomadas sem adequada ligação de fio terra podem transmitir voltagens perigosas a peças metálicas expostas.

EQUIPAMENTO DE LIGAÇÃO, a tomada eléctrica deve estar instalada perto do equipamento e ser de fácil acesso.”

CUIDADO: As aberturas de ventilação não devem ser bloqueadas e devem ter acesso livre ao ar ambiente para arrefecimento adequado do aparelho.

TEMPERATURA DE FUNCIONAMENTO: Este produto foi projetado para uma temperatura ambiente máxima de 40 graus centígrados.

ELÉTRICO - SOBRECARGA DA REDE DE CORRENTE ALTERNADA (AC)

Antes de instalar o produto, verifique o efeito cumulativo da conexão de diversos aparelhos àrede de corrente alternada através das etiquetas que indicam potência ou amperagem.

CUIDADO: CARREGAMENTO - O equipamento deverá ser montado no suporte de montagem de forma tal que não cause perigo devido a carregamento não uniforme.

Bateria de lítio - Só deve ser trocada por técnico qualificado e treinado.

CUIDADO: Se a bateria não for devidamente instalada há perigo de explosão.

Substitua somente pelo mesmo tipo ou equivalente, conforme recomendado pelo fabricante. Descarte baterias usadas, de acordo com as instruções fornecidas pelo fabricante.

TODOS OS PAÍSES: Instale o produto de acordo com as normas nacionais e locais para instalações elétricas.

Seguridad

ADVERTENCIA: en un entorno doméstico, este producto puede causar radiointerferencias, en cuyo caso, puede requerirse del usuario que tome las medidas que sean convenientes al respecto.

¡ADVERTENCIA! Producto láser Clase 1.

¡ADVERTENCIA! No mirat fijamente el haz.

32 AT-8600 Series Switch

AVISOS ELECTRICOS

ADVERTENCIA: PELIGRO DE ELECTROCHOQUE

Para evitar un ELECTROCHOQUE, no quite la tapa. No hay ningún componente en el interior al cual puede prestar servicio el usuario. Esta unidad contiene VOLTAJES PELIGROSOS y sólo deberá abrirla un técnico entrenado y calificado.

PELIGRO DE RAYOS

PELIGRO: NO REALICE NINGUN TIPO DE TRABAJO O CONEXION en los equipos o en LOS CABLES durante TORMENTAS ELECTRICAS.

ATENCION: EL CABLE DE ALIMENTACION SE USA COMO UN

DISPOSITIVO DE DESCONEXION. PARA DESACTIVAR EL EQUIPO, desconecte el cable de alimentación.

ELECTRICO - EQUIPO DEL TIPO CLASE 1

ESTE EQUIPO TIENE QUE TENER CONEXION A TIERRA. El cable tiene que conectarse a un enchufe a tierra debidamente instalado. Un enchufe que no está correctamente instalado podría ocasionar tensiones peligrosas en las partes metálicas que están expuestas.

EQUIPO CONECTABLE, el tomacorriente se debe instalar cerca del equipo, en un lugar con acceso fácil”.

ATENCION: Las aberturas para ventilación no deberán bloquearse y deberán tener acceso libre al aire ambiental de la sala para su enfriamiento.

TEMPERATURA REQUERIDA PARA LA OPERACIÓN: Este producto está diseñado para una temperatura ambiental máxima de 40 grados C.

ELECTRICO - SOBRECARGA DEL CIRCUITO PRIMARIO DE CORRIENTE

ALTERNA

Al instalarse el producto deberán considerarse las potencias nominales acumulativas, cuando se conecta el equipo al cable de alimentación de corriente alterna.

ATENCION: CARGA MECANICA - El montaje del equipo en el bastidor debe realizarse de manera tal que no cause una condición peligrosa debido a la distribución desigual del peso.

Batería de litio - Sólo deberá ser cambiada por un técnico entrenado y calificado.

ATENCION: Peligro de explosión si la batería no se reemplaza en forma correcta. Reemplace sólo con el mismo tipo o equivalente que recomienda el fabricante. Deseche las baterías usadas según las instrucciones del fabricante.

PARA TODOS LOS PAÍSES: Monte el producto de acuerdo con los Códigos

Eléctricos locales y nacionales.

Installation & Safety Guide

Säkerhet

33

VARNING: Denna produkt kan ge upphov till radiostörningar i hemmet, vilket kan tvinga användaren till att vidtaga erforderliga åtgärder.

VARNING! Laserprodukt av klass 1.

VARNING! Laserstrålning när enheten är öppen.

TILLKÄNNAGIVANDEN BETRÄFFANDE ELEKTRICITETSRISK:

RISK FÖR ELEKTRISK STÖTFör att undvika ELEKTRISK stöt, ta ej av locket.

Det finns inga delar inuti som behöver underhållas. Denna apparat är under

HÖGSPÄNNING och får endast öppnas av en utbildad kvalificerad tekniker.

FARA FÖR BLIXTNEDSLAG

FARA: ARBETA EJ på utrustningen eller kablarna vid ÅSKVÄDER.

VARNING: NÄTKABELN ANVÄNDS SOM STRÖMBRYTARE FÖR ATT

KOPPLA FRÅN STRÖMMEN, dra ur nätkabeln.

ELEKTRISKT - TYP KLASS 1 UTRUSTNING

DENNA UTRUSTNING MÅSTE VARA JORDAD. Nätkabeln måste vara ansluten till ett ordentligt jordat uttag. Ett felaktigt uttag kan göra att närliggande metalldelar utsätts för högspänning. Apparaten skall anslutas till jordat uttag, när den ansluts till ett nätverk.

UTRUSTNING MED PLUGG. Uttaget skall installeras i utrustningens närhet och vara lättåtkomligt”.

VARNING: Luftventilerna får ej blockeras och måste ha fri tillgång till omgivande rumsluft för avsvalning.

DRIFTSTEMPERATUR: Denna produkt är konstruerad för rumstemperatur ej

överstigande 40 grader Celsius.

ELEKTRISKT - ÖVERBELASTNING AV VÄXELSTRÖMSNÄTET: När produkten installeras bör den sammanlagda effekten på namnplåten beaktas när apparaten ansluts till växelströmsnätet.

VARNING: MEKANISK BELASTNING: Utrustningen ska installeras i chassit på så sätt att fara inte uppstår p g a ojämn belastning.

34 AT-8600 Series Switch

Litium batteri - Får endast bytas av utbildade och kvalificerade tekniker.

VARNING: Risk för explosion om felaktigt batteri används. Byt endast mot samma eller likvärdig typ batteri, rekommenderat av tillverkaren. Kassera använda batterier i enlighet med tillverkarens instruktioner.

ALLA LÄNDER: Installera produkten i enlighet med lokala och statliga bestämmelser för elektrisk utrustning.

Installation & Safety Guide

EC Declaration of Conformity

35

We:

ALLIED TELESIS LABS LIMITED

27 NAZARETH AVENUE

CHRISTCHURCH 8024

NEW ZEALAND

Declare under our sole legal responsibility that the following product meets the safety, protection and conformity requirements of council directives 73/23/EEC as amended by 93/68/EEC, and 89/336/EEC as amended by 93/68/EEC, 92/31/

EEC and 91/263/EEC, on the approximation of the laws of member states relating to electromagnetic compatibility and electrical safety.

AT-8600 SERIES SWITCHES

to which this declaration relates are in conformity with the following relevant harmonized standards, the reference numbers of which have been published in the Official journal of the European community.

EN55022: 1998

Incl A1:2000 and A2:2003

EN55024: 1998

Incl A1:2001 and A2:2003

EN60950-1: 2001

EN60825-1: 1994

Incl A1:2002 and A2:2001

EN61000-3-2: 2000

EN61000-3-3: 1995

Incl A1:2001

Information Technology Equipment—Radio disturbance

Information Technology Equipment—Immunity characteristics—

Limits and methods of measurement.

Information Technology Equipment including electrical business equipment—General Requirements.

Safety of Laser Products - part 1: Equipment classification, requirements and user’s guide.

Electromagnetic compatibility (EMC) - part 3-2: Limits for harmonic current emissions (equipment input current up to and including 16A per phase).

Electromagnetic compatibility (EMC) - part 3-3: Limitation of voltage fluctuations and flicker in low-voltage supply systems for equipment with rated current up to 16A.

Name: John Shields

On behalf of the Manufacturer

Signature:

Position: Hardware and Services Manager

Date: 2nd November 2005

A5 Installation and Safety Guide Cover

AT-8600 Series Switch

Installation and Safety Guide

AT-8624T/2M

AT-8624PoE

AT-8648T/2SP

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Key Features

  • Managed L3 SNMP 2, RMON 1, RMON 2, RMON 3, RMON 9, Telnet, SNMP 3, HTTP
  • Basic switching RJ-45 Ethernet ports quantity: 48
  • MAC address table: 8000 entries
  • 1U Stackable

Related manuals