ENERGENIE ENERGENIE MIHO010 MiHome 1-Gang Light Dimmer Switch Operating instructions

MI|Home Dimmer
Quick Start Guide
The Dimmer is part of the MiHome home automation
range and allows you to achieve desired light levels. The
product can be controlled manually via the push button.
Used with a MiHome Gateway (MIHO001) registered to
a MiHome account, it can also be controlled remotely
via a mobile app or through a browser.
In the Box:
Dimmer, Screw Fittings, User Guide
Compatibility
We recommend incandescent & halogen bulbs which
are 250W max, or dimmable LED bulbs which are
maximum 50W in total and not exceeding 6 bulbs per
Dimmer. Not suitable for fluorescent, non-dimmable
LED and CFL bulbs or any light requiring line drivers.
Installation
This device operates at UK mains voltage levels,
therefore, we advise installation from a competent,
qualified person. It can fit into a 25mm metal pattress or
35mm dry lining pattress box, but not into a 4 lug box.
NOTE: Can only be used in a two way switching
configuration with a MiHome slave switch. Using any
other switch as a slave will damage the Dimmer.
IMPORTANT:
Applicable in England and Wales, where the installation
of this product falls under the scope of the Building
Regulations requirements for Part P, the installation
must be carried out by registered competent persons,
and work should be designed and installed, and
inspected, tested and certificated in accordance with
BS 7671.
Applicable in Scotland, where the installation of this
product falls under the Building (Scotland) Act, a
Warrant may be required and advice should be sought
from LABSS (Local Authority Building Standards
Scotland). We recommend that a competent qualified
person is used for all installations of this product.
6. Dimmer should now be visible in the device list (may
iiiitake a few seconds depending on network speed).
Pairing via a Browser
1. Log into your account at www.mihome4u.co.uk.
2. Ensure there is power to the dimmer, and the dimmer
iiiiis switched off.
3. Select “Pair New Device”, then click on the “Dimmer”
iiiiicon from the available options. Next click the “Pair
iiiiDevice” button.
4. Follow on-screen pairing instructions, pressing the
iiiidimmer button when required for at least 8 seconds
iiiiuntil the LED begins to flash, and then release.
5. The LED will flash rapidly for a few seconds to
iiiiindicate that the dimmer is being paired, the LED will
iiiigo off when this is complete.
6. Dimmer should now be visible in the device list (may
iiiitake a few seconds depending on network speed).
NOTE: A single press of the button while it is flashing
will take it out of pairing mode. The Dimmer can be
paired with up to 3 separate Gateways. Further attempts
to pair will overwrite previous pairings.
Reset
1. Resetting the dimmer will clear the memory of all
iiiipaired devices.
2. Ensure there is power to the dimmer, and the dimmer
iiiiis switched off.
3. To reset the dimmer, press and hold the button for 30
iiiiseconds, until the LED has returned to off.
iiiiDuring these 30 seconds, the LED sequence will be,
iiiiOff => Slow Flash => On => Quick Flash => Off.
Manual operation
A single short press of the button on the front of the
housing will simply toggle the Dimmer on or off at the
previous light level. Holding the button down will cycle
through the available light levels.
Pairing with the MiHome Gateway
In order to control your Dimmer from a mobile app.
or from a browser, it needs to first be paired with the
MiHome Gateway, as follows:
Disposal
The outer box of the packaging is 70% recycled material
from managed forests and is 100% recyclable. Do not
dispose of the Dimmer with regular household waste.
You must take electronic equipment to a local recycling
centre to be disposed of in line with current regulations.
Pairing via the App on your Smartphone
1. Log into your MiHome account on the MiHome App
2. Ensure there is power to the dimmer, and the dimmer
iiiiis switched off.
3. Select “Add new device” and then choose “Dimmer”.
4. Follow onscreen pairing instructions, pressing the
iiiidimmer button when required for at least 8 seconds
iiiiuntil the LED begins to flash, and then release.
5. The LED will flash rapidly for a few seconds to
iiiiindicate that the dimmer is being paired, the LED will
iiiigo off when this is complete.
Safety
You must only use the product in dry areas indoors, and
it must be protected from moisture and water. Do not
disassemble, other than as described in the installation
section of this user guide, as it does not contain any
parts to service. This device and associated software are
for use solely in domestic, commercial and light
industrial environments, and should not be used in
applications which require safety critical, or high risk
applications. For more information please see the full
user manual for this product.
Installation Example
Technical Specification
- Rating: 220 - 240V~ 50Hz, 1A, 250W max.
- Terminal Connections: L (Line in), L1 (Line out), Slave
(MiHome only)
- Radio: 433.92MHz ISM short range
- Range: Approx. 15-20m in closed; 30m in open area
- Operating temp. : -5°C to 40°C
- Storage temp. : -20°C to +60°C
- Mounting: 25mm metal pattress; 35mm dry lining
- Size (HxWxD): 85mm x 85mm x 28mm; Weight: 95g
- Protection class: IP20
Further Help
If you have any questions regarding your product or
you believe it to be faulty, please visit
www.mihome4u.co.uk/troubleshooting and/or
www.energenie4u.co.uk where you can download a
more comprehensive user manual, or contact us directly
on tel: 08000 469 466 or e-mail:
[email protected].
Simplified EU Declaration of Conformity
Hereby, Sandal Plc, T/a Energenie declares that the
radio equipment type MIHO010 Dimmer is in
compliance with the following Directives: 2014/53/EU
Radio Equipment Directive (Article 3.1 a & b, and 3.2),
2012/19/EU Waste Electrical and Electronic Equipment
(WEEE) Directive & 2011/65/EU Restriction of the Use of
Certain Hazardous Substances (RoHS) Directive Recast.
Copyright Notice
© 2018 Sandal Plc.
Quick Start Guide
Part no: MIHO010
Energenie and MiHome are brand names of Sandal Plc.
Registered Office: Claremont House, Deans Court, Bicester,
Oxon, OX26 6BW
Version: 1.0
March 2018
The full text of the EU declaration of conformity is
available within the full user manual which can be
downloaded at the following internet address:
www.energenie4u.co.uk
The Technical Construction File required is maintained
at the company headquarters at 5 Harold Close, The
Pinnacles, Harlow, Essex, England, CM19 5TH.
Warranty
If you do not install the product and use it in line with
this guide the warranty will become invalidated and we
will not be liable for any damage or loss whatsoever,
including indirect loss, damage to property or personal
injury. Your statutory rights are not affected.