Emerson CF220GLZ00 Owner`s manual

BP7360 JULIANNE
9/19/07
11:15 AM
Page 1
READ AND SAVE THESE INSTRUCTIONS
JULIANNE™
Ceiling Fan
Owner's Manual
Model Numbers
CF220GBZ00
CF220GLZ00
Gilded Bronze with
Dark Cherry/
Walnut Blades
Gilded Silver with
Natural Cherry/
Mahogany Blades
CF220AGW00
Aged Walnut with
Teak/Mahogany Blades
Net Weight:
Part No. F40BP73600001
33.7
Lbs.
Form No. BP7360-1
U.L. Model No.: CF220
BP7360 JULIANNE
9/19/07
11:15 AM
!
Page 2
WARNING
WARNING: To avoid fire, shock, and serious personal injury, follow these
instructions.
Safety Instructions
1. Read your owner’s manual carefully and keep it for future reference.
2. Before servicing or cleaning unit, switch power off at service panel and lock service
panel disconnecting means to prevent power from being switched on accidentally.
When the service disconnecting means cannot be locked, securely fasten a
warning device, such as a tag, to the service panel.
3. Be careful of the fan and blades when cleaning, painting, or working near the fan.
Always turn off the power to the ceiling fan before servicing.
4. Do not put anything into the fan blades while they are turning.
5. Do not operate reversing switch until fan blades have come to a complete stop.
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned off at the fuse box before
wiring, and do not operate fan without blades.
2. The installation is to be in accordance with the National Electrical Code, ANSI/NFPA
70-1999 and Local Codes. Use the National Electrical Code if Local Codes do not
exist. The ceiling fan must be grounded as a precaution against possible electrical
shock. Electrical installation should be made or approved by a licensed electrician.
3. The outlet box and joist must be securely mounted and capable of reliably
supporting at least 50 pounds. Use only U.L. outlet boxes listed as “Acceptable for
Fan Support”, and use the mounting screws provided with the outlet box. Most
outlet boxes commonly used for support of light fixtures are not
acceptable for fan support and may need to be replaced. Consult a qualified
electrician if in doubt.
4. The longer downrod furnished with the fan provides the minimum
recommended floor to fan blade clearance for a 9 foot ceiling. The 6” downrod
(supplied) must be used for an 8 foot ceiling.
5. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent
accidental contact with the fan blades.
6. Follow the recommended instructions for the proper method of wiring your ceiling
fan. If you do not know enough about electrical wiring, have your fan installed by a
licensed electrician.
NOTE: This fan is suitable for use with solid-state speed controls.
WARNING: To reduce the risk of fire or electric shock, this fan should only be used
with fan speed control Model No. UC7067RC, manufactured by Rhine Electric Co., Ltd.
WARNING: This product is designed to use only those parts supplied with this
product and/or any accessories designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or accessories not designated for use with
this product by Emerson Electric Co. could result in personal injury or
property damage.
WARNING: To reduce the risk of personal injury, do not bend the blade flange when
installing the blade flanges, balancing the blades or cleaning the fan. Do not insert
foreign objects in between rotating fan blades.
DATE CODE:
The date code of this fan may be found on the box, stamped in ink on a white label.
You should record this data above and keep it in a safe place for future use.
2
U.L. Model No.: CF220
BP7360 JULIANNE
9/19/07
11:15 AM
Page 3
This Manual Is Designed to Make it as Easy as Possible for You to
Assemble, Install, Operate and Maintain Your Ceiling Fan
Tools Needed for Assembly
Installed Wire Length
Up to 50 ft.
50-100 ft.
One Phillips head screwdriver
One wire stripper
One stepladder
Seven wire connectors (supplied)
Three 40-watt (maximum) Candelabra
bulbs
!
Wire Size A.W.G.
14
12
WARNING
Before assembling your ceiling fan, refer
to section on proper method of wiring
your fan (page 11). If you feel you do not
have enough wiring knowledge or
experience, have your fan installed by a
licensed electrician.
Materials
Wiring, outlet box and box connectors
must be of type required by the local code.
The minimum wire would be a 3-conductor
(2-wire with ground) of the following sizes:
Unpacking Instructions
For your convenience, check-off boxes are provided next to each step. As each
step is completed, place a check mark in the box. This will insure that all steps
have been completed and will be helpful in finding your place should you be
interrupted.
!
NOTE: If you are uncertain of part
description, refer to exploded view
illustration.
WARNING
Do not install or use fan if any part is
damaged or missing. Call Toll-Free:
a.
b.
c.
d.
e.
f.
g.
h.
Fan motor and housing assembly
One coupling cover
One ceiling cover
Five blade flanges
Five fan blades
One switch cup assembly
One hanger bracket
One hanger ball/downrod (18”)
assembly
i. One 6” downrod
j. One lower glass
k. One decorative ring/light fitter
assembly
l. One decorative cap
m. One finial nut
n. Three downrod scrolls
o. One scroll collar assembly
p. One Fan/Light Wall Control
(transmitter and receiver)
1-800-654-3545
!
WARNING
This product is designed to use only
those parts supplied with this product
and/or any accessories designated
specifically for use with this product by
Emerson Electric Co. Substitution of
parts or accessories not designated for
use with this product by Emerson Electric
Co. could result in personal injury or
property damage.
1. Open styrofoam unit containing fan.
Remove top half of styrofoam unit.
Remove parts and check to see that
you have received the following parts:
3
U.L. Model No.: CF220
BP7360 JULIANNE
9/19/07
11:15 AM
Page 4
NOTE: Place the parts from the loose
parts bags in a small container to keep
them from being lost.
q. One loose parts bag containing:
1. Two 1-1/4” threaded studs
2. Two knurled knobs
3. Two lockwashers
4. Seven wire connectors
5. One clevis pin/hairpin clip
assembly
6. Eleven 1/4-20 x 13mm oval head
screws
7. Sixteen 10-24 x 8mm pan head
screws
8. Sixteen flat washers
9. Three 8-32 x 7mm pan head
screws
10. Two 1/8-27 nuts
11. One 1/8-27 lockwasher
12. One metal washer
13. One rubber washer
14. One hex wrench
2. Remove the fan motor and housing
assembly from the protective plastic
bag. Place the fan assembly into the
lower foam pad with the bottom of the
motor facing up.
The lower foam pad serves as a holder
for the fan during the first stages of
assembly.
A
D
C
B
G
F
E
H
I
J
K
L
M
N
P
Q
O
HI
LIGHT
MED
LOW
FAN OFF
EMERSON®
OFF
4
ON
U.L. Model No.: CF220
BP7360 JULIANNE
9/19/07
11:15 AM
Page 5
Electrical Requirements
Ceiling Fan Procedures
IMPORTANT: Your ceiling fan will not
function properly, and may be
damaged, if used with any wall dimmer
switch or control other than the
Emerson Electric Fan/Light Wall
Control supplied with the fan, or an
optional Emerson Electric SR100
Remote Control.
General
Your Emerson ceiling fan comes supplied
with a Fan/Light Wall Control which
consists of a wall control (transmitter) and
a remote control receiver mounted under
the ceiling cover. This system allows you
to regulate your ceiling fan speed and light
intensity.
Your new ceiling fan will require a
grounded electrical supply line of 120 volts
AC, 60 Hz, 15 amp circuit.
NOTE: An optional Emerson Electric
SR100 Remote Control may also be
used to control your ceiling fan.
The outlet box must be securely anchored
and capable of withstanding a load of at
least 50 pounds.
How to Assemble Your
Ceiling Fan
!
!
WARNING
Turning off wall switch is not sufficient.
To avoid possible electrical shock, be
sure electricity is turned off at the main
fuse or circuit breaker box before wiring.
All wiring must be in accordance with
National and Local codes and the ceiling
fan must be properly grounded as a
precaution against possible electrical
shock.
To reduce the risk of fire, electric shock,
or personal injury, mount fan to outlet box
marked “Acceptable for Fan Support”,
and use screws supplied with outlet box.
Most outlet boxes commonly used for
support of light fixtures are not
acceptable for fan support and may need
to be replaced. Consult a qualified
electrician if in doubt.
IMPORTANT: Before assembling your
ceiling fan, refer to sections “Setting
Operating Frequency of Wall Control
and Receiver” and “Installation of Wall
Control”, page 13. These sections
instruct you how to: a) Set the
operating frequency of the fan/light
wall control and the remote control
receiver; and b) Install the fan/light wall
control in the wall box. You will then be
ready to proceed with the assembly
and installation of your ceiling fan, as
follows:
If your fan is to replace an existing ceiling
light fixture, turn electricity off at the main
fuse or circuit breaker box at this time and
remove the existing light fixture.
!
WARNING
WARNING
Turning off wall switch is not sufficient.
To avoid possible electrical shock, be
sure electricity is turned off at the main
fuse or circuit breaker box before wiring.
All wiring must be in accordance with
National and Local codes and the ceiling
fan must be properly grounded as a
precaution against possible electrical
shock.
1. Mount the fan blades to the blade
flanges using three 10-24 x 8mm pan
head screws and three flat washers
(screws and washers supplied)
(Figure 1).
!
WARNING
To reduce the risk of personal injury, do
not bend the blade flange when installing
the blade flanges, balancing the blades or
cleaning the fan. Do not insert foreign
objects in between rotating fan blades.
5
U.L. Model No.: CF220
BP7360 JULIANNE
9/19/07
11:15 AM
Page 6
5. Gently snug all flange screws to the
motor hub, working around the hub in a
clockwise sequence. Next, securely
tighten all flange screws, again working
in a clockwise sequence. Failure to
follow this procedure could result in fan
wobble. This completes the blade
installation.
10-24 X 8mm PAN
HEAD SCREW (3)
FLAT WASHER (3)
FAN
BLADE
NOTE: If you wish to assemble your
ceiling fan without the lower light
installed, skip steps 6 and 7, and
proceed to install the switch cup
assembly in accordance with steps 8
and 9.
BLADE FLANGE
6. Remove the plastic plug from the
center hole in the switch cup assembly.
Pass the two light fitter wires through
the center hole, then screw the switch
cup assembly onto the light fitter
threaded nipple (Figure 3). Install a
lockwasher and 1/8-27 nut (supplied)
on the threaded nipple to secure the
switch cup assembly to the decorative
ring/light fitter assembly.
Figure 1
2. Remove and discard the four shipping
retainers securing the motor hub in the
motor housing.
NOTE: Take care not to scratch the fan
housing when installing the blade
assemblies.
3. Insert an 1/4-20 x 13mm oval head
screw (supplied) into each of the two
recessed holes in one of the blade
flanges.
DECORATIVE RING/LIGHT
FITTER ASSEMBLY
4. Rotate the motor hub so that two
threaded holes line up with the two
notches in the switch cup plate
(Figure 2). Position the blade flange on
the motor hub so that the screws in the
blades flange align with the two
threaded holes in the motor hub.
Loosely tighten the screws at this time.
Repeat this procedure for the
remaining four blade assemblies.
WHITE WIRE
WHITE WIRE
BLUE
WIRE
BLACK WIRE
SWITCH CUP PLATE
SWITCH CUP
ASSEMBLY
1/8-27 NUT &
LOCKWASHER
LIGHT
FITTER
Figure 3
NOTCH
1/4-20 x 13mm OVAL HEAD
SCREWS (2)
BLADE
FLANGE
7. Connect the white wire from the light
fitter to the white wire in the switch cup
assembly (Figure 3). Connect the black
wire from the light fitter to the blue wire
in the switch cup.
MOTOR HUB
Figure 2
6
U.L. Model No.: CF220
BP7360 JULIANNE
9/19/07
11:15 AM
Page 7
8. Carefully rest the decorative ring/light
fitter/switch cup assembly on the fan
blades, then engage the connector of
the switch cup assembly with the motor
connector (Figure 4). The two
connectors are keyed and color-coded
and must be mated correctly (color-tocolor) before they can be engaged.
Make sure the connectors are engaged
properly.
SWITCH CUP
ASSEMBLY
8-32 x 7mm PAN
HEAD SCREWS (3)
SWITCH CUP ASSEMBLY
Figure 5
10. Position the top and bottom halves of
the styrofoam packaging side-by-side
on the floor with a six to eight inch gap
between the halves (Figure 6).
Carefully place the partially assembled ceiling fan on the styrofoam
halves, with the light fitter assembly
positioned in the gap and the fan
assembly resting on the decorative
ring.
SWITCH CUP
CONNECTOR
MOTOR
CONNECTOR
STYROFOAM
PACKAGING
Figure 4
PARTIALLY
ASSEMBLED FAN
8-32 x 7mm PAN
HEAD SCREW (2)
9. Partially install two 8-32 x 7mm pan
head screws (supplied) in the outer rim
of the switch cup plate (Figure 4).
Engage the L-slots in the switch cup
assembly with these screws; rotate the
switch cup and tighten the two screws.
Install another 8-32 x 7mm pan head
screw in the remaining hole in the
switch cup (Figure 5).
6" - 8"
GAP
Figure 6
CAUTION: Before installing and
tightening the screws, be sure there are
no wires pinched between the switch
cup plate and switch cup assembly.
7
U.L. Model No.: CF220
BP7360 JULIANNE
9/19/07
11:15 AM
Page 8
11. Remove the hanger ball by loosening
the setscrew in the hanger ball until
the ball falls freely down the downrod
(Figure 7). Remove the pin from the
downrod, then remove the hanger
ball. Retain the pin and hanger ball for
reinstallation in step 18.
!
WARNING
It is critical that the clevis pin in the motor
coupling is properly installed and the
setscrew securely tightened. Failure to
verify that the pin and setscrew are
properly installed (as shown in Figure 8)
could result in the fan falling.
PIN
DOWNROD
HAIRPIN
CLIP
HANGER
BALL
DOWNROD
SETSCREW
CLEVIS
PIN
MOTOR
COUPLING
Figure 7
NOTE: If you have an eight-foot ceiling,
you will have to use the 6” downrod
(supplied) in order to maintain the
necessary blade-to-floor clearance of
seven feet.
SETSCREW (2)
12. Unscrew the two upper setscrews
(Figure 8) until they clear the inside of
the motor coupling. Then separate,
untwist and unkink the three 80”
motor leads. Route the motor lead
wires through the downrod. Align the
clevis pin holes in the downrod with
the holes in the motor coupling. Install
the clevis pin and secure with the
hairpin clip (Figure 8). The clevis pin
must go through the holes in the
motor coupling and the holes in the
downrod. Be sure to push the straight
leg of the hairpin clip through the hole
near the end of the clevis pin until the
curved portion of the hairpin clip
snaps around the clevis pin. The
hairpin clip must be properly installed
to prevent the clevis pin from working
loose. Pull up on the downrod to
make sure the clevis pin is properly
installed.
Figure 8
13. Tighten the two upper setscrews
(Figure 8) securely while pulling up on
the downrod.
NOTE: The setscrews must be properly
installed as described above, or fan
wobble could result.
14. Make sure the grommet is properly
installed in the coupling cover, then
slide the coupling cover over the
downrod until it rests on the motor
housing (Figure 9).
NOTE: If you installed the 6” downrod,
the three downrod scrolls and scroll
retaining ring will not be installed.
Disregard steps 15 through 17;
proceed to step 18.
8
U.L. Model No.: CF220
BP7360 JULIANNE
9/19/07
11:15 AM
Page 9
!
SCROLL
COLLAR
SETSCREW
GROMMET
COUPLING
COVER
MOTOR
HOUSING
WARNING
It is critical that the pin in the hanger ball
is properly installed and the setscrew
securely tightened. Failure to verify that
the pin and setscrew are properly
installed could result in the fan falling.
SCROLL
RETAINING
SCREW
DOWNROD
SCROLL
DOWNROD
18. Place the ceiling cover over the
downrod. Then reinstall the hanger
ball (Figure 10) on the downrod as
follows. Route the three 80” motor
leads through the hanger ball and
slide the hanger ball over the
downrod. Position the pin through the
two holes in the downrod and align
the hanger ball so the pin is captured
in the groove in the top of the hanger
ball. Pull the hanger ball up tight
against the pin and securely tighten
the setscrew in the hanger ball. A
loose setscrew could create fan
wobble.
Figure 9
15. Unscrew the three scroll retaining
screws from the scroll collar. Using
the hex wrench (supplied), unscrew
the setscrew in the scroll collar until it
clears the inside of the collar. Slide
the collar over the downrod (Figure
9), and position the collar 7 or 8inches above the coupling cover, then
tighten the setscrew.
PIN
DOWNROD
16. Align one downrod scroll with one of
the slots in the scroll collar and secure
the scroll in place using a scroll
retaining screw (previously removed)
(Figure 9). Repeat this procedure for
the remaining two downrod scrolls.
HANGER BALL
SETSCREW
CEILING
COVER
Figure 10
19. The fan comes with blue, black and
white leads that are 80” long. Before
installing the fan, measure up
approximately 6 to 9-inches above top
of hanger ball/downrod assembly. Cut
off excess leads and strip back
insulation 1/2” from end of leads.
NOTE: The downrod scrolls must
properly mate with the slots in the
scroll collar to assure proper
alignment. Securely tighten the screws.
17. Loosen the setscrew and slide the
scroll collar down the downrod until
the decorative scrolls rest upon the
top of the motor housing (Figure 9).
Tighten the setscrew.
20. You have now completed the initial
assembly of your new ceiling fan. You
can now proceed with hanging and
wiring your fan.
9
U.L. Model No.: CF220
BP7360 JULIANNE
9/19/07
11:15 AM
Page 10
How to Hang
Your Ceiling Fan
!
!
WARNING
Hanger bracket must seat firmly
against outlet box. If the outlet box is
recessed, remove wall board until
bracket contacts box. If bracket
and/or outlet box are not securely
attached, the fan could wobble or
fall.
WARNING
The fan must be hung with at least 7'
of clearance from floor to blades
(Figure 11).
CEILING
OUTLET
BOX
TWO SCREWS
SUPPLIED
WITH
OUTLET BOX
HANGER
BRACKET
TAB
AT
LEAST
7'
Figure 12
2. Carefully lift the fan and seat the hanger
ball/downrod assembly on the hanger
bracket that was just attached to the
outlet box (Figure 13). Be sure the
groove in the ball is lined up with the tab
on the hanger bracket (Figure 12).
FLOOR
Figure 11
!
WARNING
!
The outlet box and joist must be
securely mounted and capable of
supporting at least 50 lbs. Use only a
U.L. outlet box listed as “Acceptable
for Fan Support”.
!
WARNING
Failure to seat tab in groove could
cause damage to electrical wires and
possible shock or fire hazard.
NOTE: CEILING COVER, SUPPLY WIRES AND FAN
WIRES OMITTED FOR CLARITY.
WARNING
To reduce the risk of fire, electric
shock, or personal injury, mount fan
to outlet box marked “Acceptable for
Fan Support”, and use screws
supplied with outlet box. Most outlet
boxes commonly used for support of
light fixtures are not acceptable for
fan support and may need to be
replaced. Consult a qualified
electrician if in doubt.
OUTLET
BOX
HANGER
BRACKET
HANGER BALL/
DOWNROD
ASSEMBLY
Figure 13
!
1. Securely attach the hanger bracket to
the outlet box using the two screws
supplied with the outlet box (Figure 12).
WARNING
To avoid possible fire or shock, do
not pinch wires between the hanger
ball/downrod assembly and hanger
bracket.
10
U.L. Model No.: CF220
BP7360 JULIANNE
9/19/07
11:15 AM
Page 11
How to Wire
Your Ceiling Fan
including ground, and that no bare wire
is visible at the wire connectors, except
for the ground wire.
2. Refer to Figures 14 and 15 and connect
the receiver wires to the supply wires
and the fan motor wires as follows:
a. Securely connect the green grounding
wires from the hanger ball and the
hanger bracket to the supply grounding
conductor (this may be a bare wire or a
wire with green insulation).
b. Securely connect the supply white
(neutral) wire to the receiver white
(AC IN N) wire.
c. Securely connect the supply black wire
(hot) wire to the receiver black (AC IN
L) wire.
d. Securely connect the fan motor white
wire to the receiver white (TO MOTOR
N) wire.
e. Securely connect the fan motor black
wire to the receiver red (TO MOTOR L)
wire.
f. Securely connect the fan motor blue
wire to the receiver blue (FOR
LIGHT) wire.
If you feel that you do not have enough
electrical
wiring
knowledge
or
experience, have your fan installed by a
licensed electrician.
!
WARNING
Turning off wall switch is not
sufficient.
To
avoid
possible
electrical shock, be sure electricity is
turned off at the main fuse box
before wiring. All wiring must be in
accordance with National and Local
codes and the ceiling fan must be
properly grounded as a precaution
against possible electrical shock.
CAUTION: To reduce the risk of
electrical shock, disconnect the
electrical supply circuit before
installing the fan, light kit or receiver.
1. Position the supply wires to the left side
of the outlet box (Figure 14); position
the fan wires to the right side. Partially
insert the remote control receiver (flat
side up) until one end rests on the
hanger ball as shown in Figure 14.
NOTE: Make all wiring connections
using wire connectors (supplied). Make
sure that all connections are tight,
Check to see that all connections are
tight, including ground, and that no
bare wire is visible at the wire
connectors, except for the ground
wire. Do not operate fan until blades
are in place. Noise and fan damage
could result.
SUPPLY WHITE WIRE
(NEUTRAL)
AC IN
SUPPLY BLACK
WIRE (HOT)
GROUND WIRE
WARNING
!
RECEIVER WHITE
WIRE
RECEIVER
BLACK WIRE
N
RECEIVER RED WIRE
ANTENNA
GREEN GROUND
WIRE FROM
HANGER BRACKET
Figure 14
1-1/4" THREADED
STUD (2)
RL
OTO
TO
M
GHT
TO MO
AC IN L
FOR LI
GREEN GROUND
WIRE FROM
HANGER BALL
TOR N
RECEIVER BLUE
WIRE
FAN
BLACK
WIRE
FAN BLUE WIRE
FAN WHITE WIRE
11
RECEIVER WHITE WIRE
U.L. Model No.: CF220
BP7360 JULIANNE
9/19/07
11:15 AM
Page 12
SW101 FAN/LIGHT WALL
CONTROL (SUPPLIED)
TO
120VOLT
SUPPLY
BLACK
BLACK
(HOT)
BLACK
HI
LIGHT
MED
LOW
FAN OFF
WHITE
EMERSON®
OFF
ON
WHITE
WHITE
GROUND
RED
TWO-CONDUCTOR
CABLE (WITH
GROUND)
BLUE
WHITE
BLACK
BLUE
WHITE
GREEN WIRE (GROUND)
FROM HANGER BALL AND
HANGER BRACKET
HANGER BALL
Figure 15
3. Push the wires and connectors up into
the outlet box while inserting the
receiver fully into the hanger bracket.
Position the antenna wire on top of the
receiver.
4. Screw the two 1-1/4” threaded studs
(supplied) into the tapped holes in the
hanger bracket (Figure 14).
5. Lift the ceiling cover up to the threaded
studs and turn until the studs protrude
through the holes in the ceiling cover
(Figure 16).
!
WARNING
To avoid possible fire or shock, make
sure that the electrical wires are
completely inside the outlet box and
not pinched between the ceiling
cover and the ceiling.
7. Screw in three 40-watt (maximum)
candelabra bulbs in the light fitter
sockets (Figure 17). Carefully place the
lower glass over the light fitter threaded
nipple. Be sure the glass is firmly
seated in the decorative ring, then
secure in place using a rubber washer,
metal washer, and nut (washers and
nut are supplied).
6. Secure the ceiling cover in place by
sliding lockwashers (supplied) over the
threaded studs and installing the two
knurled knobs (supplied). (Figure 16).
Tighten the knurled knobs securely
until the ceiling cover fits snugly against
the ceiling.
8. Place the decorative cap over the
threaded nipple and then screw on the
finial nut (Figure 17).
9. Your ceiling fan is now installed and
wired to be controlled by your fan/light
wall control.
CEILING
COVER
1-1/4"
THREADED
STUD
LOCKWASHER
(2)
KNURLED
KNOB (2)
Figure 16
12
U.L. Model No.: CF220
BP7360 JULIANNE
9/19/07
11:15 AM
Page 13
ANTENNA WIRE
DECORATIVE
RING
ON
4
CODE
SWITCH
RECEIVER
WALL CONTROL
LEVERS
3
3
2
2
1
1
40-WATT
(max.)
CANDELABRA
BULBS (3)
4
SOCKET
ON
RECEIVER
SWITCH LEVERS
THREADED
NIPPLE
LIGHT FITTER
1
ON
RUBBER
WASHER
3
CODE
SWITCH
4
WALL
CONTROL
METAL
WASHER
NUT
LOWER
GLASS
2
Figure 18
DECORATIVE
CAP
FINIAL NUT
Installation of Wall
Control
Figure 17
SINGLE-POLE INSTALLATION
Setting Operating
Frequency of Wall
Control and Receiver
(Figure 19)
HOT
FAN/LIGHT
WALL CONTROL
BLK
HI
LIGHT
MED
LOW
(Figure 18)
FAN OFF
EMERSON®
OFF
BLACK
ON
NEUTRAL
LOAD
BLACK
Your wall control and receiver have code
switches which must be set in one of 16
possible code combinations. The four
levers (numbered 1, 2, 3, and 4) on the
switches are factory-set in the ON (up)
position. Change the switch settings as
follows:
GROUND
REMOTE CONTROL
RECEIVER LOCATED
WITHIN THE CEILING
COVER
1. Slide the four switch levers in the wall
control to your choice of ON (up) or
down positions. Use a ball-point pen or
small screwdriver and slide the levers
firmly up or down.
Figure 19
1. Disconnect power at circuit breaker or
remove fuse.
2. Remove faceplate and screws from
existing wall control. Pull control out
from the wall box. Determine the “hot”
wire and the “load” wire and disconnect
these wires from control. Do not
attempt to disconnect any wires not
already connected to existing control.
2. In the receiver, slide the four switch
levers to the same positions as set in
the wall control. Make sure the levers
on both switches are in the same
positions, otherwise the fan will not
operate.
3. Before installing wall control, place wall
control in “OFF” mode by pushing
“ON/OFF” switch to the “OFF” position.
13
U.L. Model No.: CF220
11:15 AM
Page 14
3. Before installing wall control, place wall
control in “OFF” mode by pushing
“ON/OFF” switch to the “OFF” position.
WARNING
!
Do not connect any neutral (white)
wire to this control. Incorrect wiring
will damage this control.
Do not connect any neutral (white)
wire to this control. Incorrect wiring
will damage this control.
4. Connect one black wire of wall control
to the “hot” wire. Securely connect
wires with wire connectors supplied
(Figure 20).
4. Install a wall control in the wall box
containing the “hot” wire first. Connect
the black wire of the wall control to the
“hot” wire. Securely connect wires with
wire connectors supplied.
5. Connect one black wire of wall switch
to the “load” (black) wire in wall box.
Securely connect wires with wire
connector supplied.
6. Screw wall control into wall box and
install decorator style faceplate
(included). Leave wall control in “OFF”
mode until fan installation is completed.
5. Connect one black wire of the wall
control to both remaining traveler wires
in the wall box and secure with wire
connector supplied.
7. Refer to page 5 and complete the
ceiling fan installation.
K
BL
HI
LIGHT
MED
LOW
NOTE: Retrofit 3-way installations are
likely to include two traveler wires
between the two wall boxes. In new
construction, only one traveler wire Is
required.
HOT
TO
120V
AC SOURCE
TO
LOAD
3-WAY WIRlNG DIAGRAM:
NEW CONSTRUCTION
FAN OFF
EMERSON ®
ON
BL
GR
OFF
K
AC
Figure 20
OU
ND
FAN/LIGHT
WALL
CONTROL
WARNING
!
HOT
HI
LIGHT
MED
LOW
WALL
BOX
FAN OFF
EMERSON®
OFF
ON
FAN/LIGHT
WALL
CONTROL
TRAVELER
WIRE
NEUTRAL
REMOTE CONTROL
RECEIVER LOCATED
WITHIN THE CEILING
COVER
(On fan controlled by two different wall
controls) (See Figures 21 and 22.)
1. Disconnect power at circuit breaker or
remove fuse.
LIGHT
OFF
BLACK
3-WAY INSTALLATION
HI
MED
LOW
FAN OFF
EMERSON ®
ON
BLK
9/19/07
BLK
BP7360 JULIANNE
LOAD
BLACK
GROUND
Figure 21
6. Place wall control into wall box. Screw
in place and install decorator style
faceplate (included).
2. At all wall box locations remove
faceplates and screws from existing
controls. Pull controls out from wall
boxes and determine which wall box
contains the “hot” lead and which wall
box contains the “load” wire. Also,
identify traveler wires which are
common to both wall boxes.
Disconnect wires from existing controls
only. Do not attempt to disconnect any
wires not already connected to existing
controls.
7. Next, install the other wall control into
the wall box containing the load wire.
Connect the black wire of the wall
control to the traveler wire(s) already
connected to the black wire (in the
other wall box). Secure with wire
connectors supplied.
8. Connect one black wire of the wall
control to the “load” (black) wire and
secure with wire connector supplied.
14
U.L. Model No.: CF220
BP7360 JULIANNE
9.
9/19/07
11:15 AM
Page 15
Place the second wall control into the
wall box. Screw in place and install
decorator style faceplate (included).
Leave switch in “OFF” mode until fan
installation is completed.
4. To set the level of light brightness,
press and hold the LIGHT button. The
light brightness will continue to
increase then decrease while the
button is held down. When the light is
at the desired brightness, release the
button.
5. To turn the light on and off, press and
release the LIGHT button. The light will
turn on at the light level previously set
(see step 4).
6. If airflow is desired in the opposite
direction, turn the fan off and wait for
the blades to stop turning. Then slide
the reversing switch to the opposite
position (Figure 24) and turn the fan on
again. The blades will turn in the
opposite direction and reverse the
airflow.
10. Refer to page 5 and complete the
ceiling fan installation .
STANDARD WIRING FOR EXISTING
3-WAY CONTROL
HOT
EXISTING
WALL CONTROL
BLK
BLACK
HOT
BLK
LOAD
BLK
BLK
TRAVELER WIRES
BLK
HI
HI
LIGHT
LIGHT
MED
MED
LOW
LOW
FAN OFF
FAN OFF
FAN/LIGHT
WALL CONTROL
OFF
ON
ON
TRAVELER WIRES
BLACK
EMERSON ®
EMERSON ®
OFF
LOAD
Figure 22
HI
LIGHT
Operating Your
Ceiling Fan
IMPORTANT
Fan installation must be completed,
including the installation of the fan
blades, before testing of the remote
control.
Your Fan/Light Wall Control (Figure 23)
has full control of your fan and light.
However, airflow direction is controlled by
a slide switch on the switch housing.
1. Restore electrical power to the outlet
box by turning the electricity on at the
service panel.
NOTE: Make sure that the ON/OFF slide
switch on the Fan/Light Wall Control is
in the ON position.
2. To set the desired fan speed, press the
HI, MED, or LOW buttons to operate
your fan on high, medium, or low speed
(Figure 23).
3. To turn your fan off, press the OFF
button.
MED
LOW
FAN OFF
EMERSON®
OFF
ON
Figure 23
REVERSING
SWITCH
Figure 24
15
U.L. Model No.: CF220
BP7360 JULIANNE
9/19/07
11:15 AM
Page 16
Maintenance
Accessories
IMPORTANT CARE INSTRUCTIONS
for your Ceiling Fan
1. Downrod Extension Kits (see store or
catalog).
Periodic cleaning of your new ceiling fan is
the only maintenance that is needed.
2. Ceiling Fan Controls (see store or
catalog).
When cleaning, use only a soft brush or
lint free cloth to avoid scratching the finish.
!
The use of any other control not
specifically approved for this fan
could result in fire, shock and
personal injury.
Abrasive cleaning agents are not required
and should be avoided to prevent damage
to finish.
!
WARNING
WARNING
!
Do not use water when cleaning your
ceiling fan. It could damage the
motor or the blades and create the
possibility of an electrical shock.
WARNING
This product is designed to use only
those parts supplied with this
product and/or any accessories
designated specifically for use with
this product by Emerson Electric Co.
Substitution of parts or accessories
not designated for use with this
product by Emerson Electric Co.
could result in personal injury or
property damage.
INSTRUCTION TO THE USER
(if device contains a digital device)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This equipment has been certified to comply with the limits for a Class B computing device,
pursuant to FCC Rules. In order to maintain compliance with FCC regulations, shielded
cables must be used with this equipment. Operation with non-approved equipment or
unshielded cables is likely to result in interference to radio and TV reception. The user is
cautioned that changes and modifications made to the equipment without the approval of
manufacturer could void the user’s authority to operate this equipment.
This Class B digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations.
16
U.L. Model No.: CF220
BP7360 JULIANNE
9/19/07
11:15 AM
Page 17
WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX
!
OR CIRCUIT BREAKER BEFORE TROUBLE SHOOTING YOUR FAN.
Trouble Shooting
TROUBLE
1. Fan will not
start.
PROBABLE CAUSE
1. Fuse or circuit breaker
blown.
2. Loose power line
connections to the fan.
3. Fan/Light Wall Control is OFF.
4. Code switches in remote
control receiver and Fan/Light
Wall Control are not set in the
same position.
2. Fan sounds
noisy.
1. Blades not attached to fan.
2. Screws securing fan blade
flanges to motor are loose.
3. Screws holding blades to
flanges are loose.
SUGGESTED REMEDY
1. Check main and branch
circuit fuses or circuit breakers.
! WARNING: Make sure
main power is turned off.
2. Check line power connections
to fan.
3. Turn ON Fan/Light Wall Control.
4. Check that both code switches
are set in the same positions.
1. Attach blades to fan before
operating.
2. Check to make sure the screws
which attach the blade flanges
to the motor are tight.
3. Tighten screws securely.
WARNING: Make sure main
power is turned off.
4. Loose screws in motor housing. 4. Check to make sure all screws
in motor housing are snug
(not over-tight)
!
3. Fan wobbles
excessively.
1. Setscrews in motor coupling are 1. Raise coupling cover and tighten
not tightened securely.
setscrews securely.
2. Setscrew in the hanger ball/
2. Tighten the setscrew in the
downrod assembly is loose.
hanger ball/downrod assembly.
3. Screws securing fan blade
3. Check to be sure screws which
flanges to motor are loose.
attach the fan blade flanges
to the motor are tight.
4. Fan blade flanges not seated
4. Check to be sure that the
properly.
screws securing the fan
blade flanges seat firmly.
5. Hanger bracket and/or ceiling
5. Tighten the hanger bracket
outlet box is not securely
screws to the outlet box, and/or
fastened.
secure outlet box.
6. Fan blades out of balance.
6. Interchanging an adjacent (side
by-side) blade pair can
redistribute the weight and result
in smoother operation.
Or use supplied balancing kit to
balance blades.
17
U.L. Model No.: CF220
BP7360 JULIANNE
9/19/07
11:15 AM
Page 18
Repair Parts
1
2
3
5
18
21
22
4
19
7
6
8
20
23
9
10
11
14
15
25
30
29
12
13
24
35
27
HI
LIGHT
MED
LOW
34
FAN OFF
EMERSON®
OFF
26
ON
28
33
16
17
14
31
32
Before discarding packaging material, be certain all parts have been removed.
HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION:
• PART NUMBER
• NAME OF ITEM
• PART DESCRIPTION
• MODEL NUMBER
The model number of your Fan will be found on a label attached to the top housing.
For repair parts, phone 1-800-654-3545.
18
U.L. Model No.: CF220
BP7360 JULIANNE
9/19/07
11:15 AM
Page 19
Repair Parts Listing
Key
No.
*
1
2
3
*
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
*
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
—
Description
Hanger Pack, Consisting of:
Hanger Bracket
Hanger Ball
Downrod
Parts Bag, Containing:
Wire Connector (7)
Threaded Stud,
8-32 x 1-1/4” (2)
Knurled Knob (2)
Lockwasher (2)
Hairpin Clip
Clevis Pin
Screw, Pan Head,
10-24 x 8mm (16)
Washer, Flat (16)
Screw, Oval Head,
1/4-20 x 13mm (11)
Screw, Pan Head,
8-32 x 7mm (4)
Nut, 1/8-27 (2)
Lockwasher
Washer, Rubber
Washer, Flat
Wrench, Hex
Cover, Ceiling
Scroll, Decorative (3)
Collar Assembly, Scroll
Collar, Scroll
Screw, Scroll Retaining (3)
Cover, Coupling
Housing, Switch
Harness, Wiring
Fitter Assembly, Light
Ring Assembly, Decorative
Glass, Lower
Flange Set (full set for one fan)
Blade Set (full set for one fan)
Cap, Decorative
Nut, Finial
Downrod, 6”
Wall Control, Fan Light
Receiver, Remote Control
Owner's Manual
Model No.
CF220AGW00
761655-56
—
—
—
763047-2
—
Part Numbers
Model No.
CF220GLZ00
761655-55
—
—
—
763047-1
—
Model No.
CF220GBZ00
761655-54
—
—
—
763047
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
763025-AGW
763026-AGW
763027-AGW
—
—
763029-AGW
763036-AGW
763037
763038
763040-AGW
763039
763032-AGW
762635-15
763044-AGW
763045-AGW
761631-69
762348-1
762670
BP7360-1
—
—
—
—
—
—
763025-GLZ
763026-GLZ
763027-GLZ
—
—
763029-GLZ
763036-GLZ
763037
763038
763040-GLZ
763039
763032-GLZ
762635-14
763044-GLZ
763045-GLZ
761631-67
762348-1
762670
BP7360-1
—
—
—
—
—
—
763025-GBZ
763026-GBZ
763027-GBZ
—
—
763029-GBZ
763036-GBZ
763037
763038
763040-GBZ
763039
763032-GBZ
762635-13
763044-GBZ
763045-GBZ
761631-65
762348-1
762670
BP7360-1
19
U.L. Model No.: CF220
BP7360 JULIANNE
9/19/07
11:15 AM
Page 20
LIMITED WARRANTY
What The Warranty Covers:
This warranty covers the motor and the other components and accessories of your Emerson Electric Co. ceiling
fan against all defects in workmanship and materials. You must be the original purchaser or user of the product
to be covered.
What The Period Of Coverage Is:
As it applies to the motor, this warranty will last for a lifetime of your ceiling fan. All other components and
accessories are covered by this warranty for one year from the date you purchased your ceiling fan. ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, MADE WITH
RESPECT TO COMPONENTS AND ACCESSORIES IS ALSO LIMITED TO ONE YEAR.
What Will Emerson Electric Co. Do To Correct Problems:
Emerson Electric Co. will replace a defective Emerson Air Comfort Ceiling Fan motor, blade, component or other
accessory at no charge to you. If repair of the motor or blades is not practical or possible within a reasonable
time and no replacement can be provided, Emerson Electric Co. will refund the actual purchase price of your fan.
We will ship the repaired product or replacement to you at no charge, but you are responsible for all costs or
removal, reinstallation and shipping of the product to Emerson Electric Co.
How Can You Get Service:
YOU MUST HAVE PROOF OF YOUR PURCHASE OF THE CEILING FAN TO OBTAIN LIMITED WARRANTY
SERVICE. KEEP YOUR RECEIPT OR OTHER PROOF OF PURCHASE. You can return the product to our factory
or to your nearest authorized service center.
• To return the product to the factory, obtain a return authorization and service identification tag by writing to
Air Comfort Products, Division of Emerson Electric Co., 8100 W. Florissant Ave., St. Louis, MO 63136.
Include all model numbers shown on the product with your request.
• To return the product to an authorized service center, call 1-800-654-3545 for the address of the nearest
authorized service center.
You will be responsible for all insurance, freight or other transportation charges to our factory or authorized
service center. Your Emerson Air Comfort Ceiling Fan should be properly packed to avoid damage in transit
since we will not be responsible for any such damage.
What Is Not Covered:
The glass globes and light bulbs of your ceiling fan are not covered by this warranty. This warranty also does
not cover any defects, malfunctions or failures caused by:
• Repairs by persons not authorized by Emerson Electric Co.,
• Use of parts or accessories not authorized by Emerson Electric Co.,
• Mishandling, improper installation, modifications or damage to your ceiling fan while in your possession, or
• Unreasonable use, misuse, abuse, including failing to do reasonable and necessary maintenance, and normal
wear and tear.
• Additionally, this warranty and any implied warranty of merchantability or fitness for a particular purpose are
voided when:
• The original purchaser or user ceases to own the product, or
• The fan is moved from its original point of installation.
This warranty is only valid within the 50 states of the United States and the District of Columbia. No other
written or oral warranties apply, and no employee, agent, dealer or other person is authorized to give any
warranties on behalf of Emerson Electric Co.
REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE UNDER THIS
WARRANTY AND EMERSON ELECTRIC CO. IS NOT RESPONSIBLE FOR DAMAGES OF ANY KIND, INCLUDING
INCIDENTAL AND CONSEQUENTIAL DAMAGES. Incidental damages include but are not limited to such
damages as loss of time and loss of use. Consequential damages include but are not limited to the cost of
repairing or replacing other property which was damaged if this product does not work properly.
How State Law Relates To The Warranty:
Some states do not allow the exclusion or limitation of incidental or consequential damages so the above
exclusion or limitation may not apply to you. This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
Air Comfort Products
DIVISION OF EMERSON ELECTRIC CO.
8100 W. Florissant ¥ St. Louis, MO 63136
Part No. F40BP73600001
Printed in China 09/07
Form No. BP7360-1
U.L. Model No.: CF220